Skip to contentSkip to conversation

mt312: add attach-time setting to invert lnb-voltage (Matthias Schwarzott)

PATCH Eduard Huguet 2 participants 6 messages Apr 14, 2008 – Apr 27, 2008 Media (V4L/DVB)

lore
Share & tools
lore
#0 lore raw
Quoted 47 lines

---------- Missatge reenviat ----------
From: Matthias Schwarzott <[email protected]>
To: [email protected]
Date: Sat, 12 Apr 2008 17:04:50 +0200
Subject: [linux-dvb] [patch 5/5] mt312: add attach-time setting to invert lnb-voltage
Add a setting to config struct for inversion of lnb-voltage. Needed for support of Avermedia A700 cards.

Index: v4l-dvb/linux/drivers/media/dvb/frontends/mt312.c
===================================================================

linux/drivers/media/dvb/frontends/mt312.c +6 -1
@@ -422,11 +422,16 @@ static int mt312_set_voltage(struct dvb_
  {
        struct mt312_state *state = fe->demodulator_priv;
        const u8 volt_tab[3] = { 0x00, 0x40, 0x00 };
+       u8 val;
 
        if (v > SEC_VOLTAGE_OFF)
                return -EINVAL;
 
-       return mt312_writereg(state, DISEQC_MODE, volt_tab[v]);
+       val = volt_tab[v];
+       if (state->config->voltage_inverted)
+               val ^= 0x40;
+
+       return mt312_writereg(state, DISEQC_MODE, val);
  }
 
  static int mt312_read_status(struct dvb_frontend *fe, fe_status_t *s)

Index: v4l-dvb/linux/drivers/media/dvb/frontends/mt312.h
===================================================================

linux/drivers/media/dvb/frontends/mt312.h +3 -0
@@ -31,6 +31,9 @@
  struct mt312_config {
        /* the demodulator's i2c address */
        u8 demod_address;
+
+       /* inverted voltage setting */
+       int voltage_inverted:1;
  };
 
  #if defined(CONFIG_DVB_MT312) || (defined(CONFIG_DVB_MT312_MODULE) &&
Quoted 3 lines

defined(MODULE))
--

Thanks for the patches. ¿Is your lastest unified diff on your page (a700_full_20080412.diff) equivalent to these patches or must they be applied separately?

I'll try to some tests tonight, if you have made some progress. By the way, ¿could you tell me if it's better to use use_frontend=0 or 1 for saa7134-dvb module? I think that this changes the driver used for frontend, but I'm not sure.

Regards,
Eduard

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#1 lore raw

Re: [linux-dvb] a700 support (was: [patch 5/5] mt312: add attach-time setting to invert lnb-voltage (Matthias Schwarzott))

Quoted 45 lines · Eduard Huguet
Quoted 45 lines

---------- Missatge reenviat ----------
From: Matthias Schwarzott <[email protected]>
To: [email protected]
Date: Sat, 12 Apr 2008 17:04:50 +0200
Subject: [linux-dvb] [patch 5/5] mt312: add attach-time setting to invert lnb-voltage
Add a setting to config struct for inversion of lnb-voltage. Needed for support of Avermedia A700 cards.

Index: v4l-dvb/linux/drivers/media/dvb/frontends/mt312.c
===================================================================

linux/drivers/media/dvb/frontends/mt312.c +6 -1
@@ -422,11 +422,16 @@ static int mt312_set_voltage(struct dvb_
  {
        struct mt312_state *state = fe->demodulator_priv;
        const u8 volt_tab[3] = { 0x00, 0x40, 0x00 };
+       u8 val;
 
        if (v > SEC_VOLTAGE_OFF)
                return -EINVAL;
 
-       return mt312_writereg(state, DISEQC_MODE, volt_tab[v]);
+       val = volt_tab[v];
+       if (state->config->voltage_inverted)
+               val ^= 0x40;
+
+       return mt312_writereg(state, DISEQC_MODE, val);
  }
 
  static int mt312_read_status(struct dvb_frontend *fe, fe_status_t *s)

Index: v4l-dvb/linux/drivers/media/dvb/frontends/mt312.h
===================================================================

linux/drivers/media/dvb/frontends/mt312.h +3 -0
@@ -31,6 +31,9 @@
  struct mt312_config {
        /* the demodulator's i2c address */
        u8 demod_address;
+
+       /* inverted voltage setting */
+       int voltage_inverted:1;
  };
 
Quoted 7 lines
Quoted 3 lines
linux/drivers/media/dvb/frontends/mt312.h +0 -0
  #if defined(CONFIG_DVB_MT312) || (defined(CONFIG_DVB_MT312_MODULE) &&

defined(MODULE))
--

Thanks for the patches. ¿Is your lastest unified diff on your page (a700_full_20080412.diff) equivalent to these patches or must they be applied separately?

Another 2 weeks later. These patches already have been applied at hg level. So now the new remaining full patch (a700_full_20080427.diff) is to be applied on top.

It contains a zl10036 driver and the changes to the glue code in saa7134-dvb. zl10036 works most of the time here, but I am not fully happy with its current design.

Open issues:
* Should set_params routine be kept spiltted as it is?
* Is bandwidth handling sane?
Now calc the needed bw by symbolrate and add 3MHz.
Datasheet suggests to start at max setting and decrease as possible after the lock is established (using freq. offset info from demod).
* The used gain values are found by try and error and do not work for all transponders here.
The most difficult transponder here was RTL - and that now works for me with exactly these gain settings (rfg=0, ba=1, bg=1).

Quoted 5 lines

I'll try to some tests tonight, if you have made some progress. By the way, ¿could you tell me if it's better to use use_frontend=0 or 1 for saa7134-dvb module? I think that this changes the driver used for frontend, but I'm not sure.

use_frontend is intended to be used for choosing between dvb-s and dvb-t or similar if the frontend offers both exclusively. I abused this parameter to choose between the two driver for zl10313 demod. This is no longer used, so forget about this parameter.

Regards
Matthias

linux/drivers/media/dvb/frontends/Kconfig +7 -0
Index: v4l-dvb/linux/drivers/media/dvb/frontends/Kconfig
===================================================================
@@ -368,6 +368,13 @@ config DVB_TUNER_QT1010
 	help
 	  A driver for the silicon tuner QT1010 from Quantek.
 
+config DVB_ZL10036
+	tristate "Zarlink ZL10036 silicon tuner"
+	depends on DVB_CORE && I2C
+	default m if DVB_FE_CUSTOMISE
+	help
+	  A DVB-S silicon tuner module. Say Y when you want to support this tuner.
+
 config DVB_TUNER_MT2060
 	tristate "Microtune MT2060 silicon IF tuner"
 	depends on I2C
linux/drivers/media/dvb/frontends/Makefile +1 -0
Index: v4l-dvb/linux/drivers/media/dvb/frontends/Makefile
===================================================================
@@ -25,6 +25,7 @@ obj-$(CONFIG_DVB_TDA1004X) += tda1004x.o
 obj-$(CONFIG_DVB_SP887X) += sp887x.o
 obj-$(CONFIG_DVB_NXT6000) += nxt6000.o
 obj-$(CONFIG_DVB_MT352) += mt352.o
+obj-$(CONFIG_DVB_ZL10036) += zl10036.o
 obj-$(CONFIG_DVB_ZL10353) += zl10353.o
 obj-$(CONFIG_DVB_CX22702) += cx22702.o
 obj-$(CONFIG_DVB_DRX397XD) += drx397xD.o
linux/drivers/media/dvb/frontends/zl10036.c new file +700 -0

700 lines not on this page · raw message

linux/drivers/media/dvb/frontends/zl10036.h new file +67 -0

67 lines not on this page · raw message

linux/drivers/media/video/saa7134/Kconfig +2 -0
Index: v4l-dvb/linux/drivers/media/video/saa7134/Kconfig
===================================================================
@@ -38,6 +38,8 @@ config VIDEO_SAA7134_DVB
 	select DVB_TDA827X if !DVB_FE_CUSTOMISE
 	select DVB_ISL6421 if !DVB_FE_CUSTOMISE
 	select TUNER_SIMPLE if !DVB_FE_CUSTOMISE
+	select DVB_ZL10036 if !DVB_FE_CUSTOMISE
+	select DVB_MT312 if !DVB_FE_CUSTOMISE
 	---help---
 	  This adds support for DVB cards based on the
 	  Philips saa7134 chip.
linux/drivers/media/video/saa7134/saa7134-cards.c +17 -7
Index: v4l-dvb/linux/drivers/media/video/saa7134/saa7134-cards.c
===================================================================
@@ -4261,8 +4261,7 @@ struct saa7134_board saa7134_boards[] = 
 		.radio_type     = UNSET,
 		.tuner_addr     = ADDR_UNSET,
 		.radio_addr     = ADDR_UNSET,
-		/* no DVB support for now */
-		/* .mpeg           = SAA7134_MPEG_DVB, */
+		.mpeg           = SAA7134_MPEG_DVB,
 		.inputs         = { {
 			.name = name_comp,
 			.vmux = 1,
@@ -4281,8 +4280,7 @@ struct saa7134_board saa7134_boards[] = 
 		.radio_type     = UNSET,
 		.tuner_addr     = ADDR_UNSET,
 		.radio_addr     = ADDR_UNSET,
-		/* no DVB support for now */
-		/* .mpeg           = SAA7134_MPEG_DVB, */
+		.mpeg           = SAA7134_MPEG_DVB,
 		.inputs         = { {
 			.name = name_comp,
 			.vmux = 1,
@@ -5676,12 +5674,24 @@ int saa7134_board_init1(struct saa7134_d
 		break;
 	case SAA7134_BOARD_AVERMEDIA_A700_PRO:
 	case SAA7134_BOARD_AVERMEDIA_A700_HYBRID:
+#if 0
+		/* power-up tuner chip */
+		saa_andorl(SAA7134_GPIO_GPMODE0 >> 2,   0xffffffff, 0xffffffff);
+		saa_andorl(SAA7134_GPIO_GPSTATUS0 >> 2, 0xffffffff, 0xffffffff);
+		msleep(1);
+#endif
+#if 1
 		/* write windows gpio values */
 		saa_andorl(SAA7134_GPIO_GPMODE0 >> 2,   0x80040100, 0x80040100);
 		saa_andorl(SAA7134_GPIO_GPSTATUS0 >> 2, 0x80040100, 0x00040100);
-		printk("%s: %s: hybrid analog/dvb card\n"
-		       "%s: Sorry, only the analog inputs are supported for now.\n",
-			dev->name, card(dev).name, dev->name);
+#endif
+#if 0
+		/* reset demod */
+		saa7134_set_gpio(dev, 23, 1);
+		msleep(100);
+		saa7134_set_gpio(dev, 23, 3); // back to tristate = input mode
+		msleep(100);
+#endif
 		break;
 	}
 	return 0;
linux/drivers/media/video/saa7134/saa7134-dvb.c +26 -0
Index: v4l-dvb/linux/drivers/media/video/saa7134/saa7134-dvb.c
===================================================================
@@ -49,6 +49,9 @@
 #include "lnbp21.h"
 #include "tuner-simple.h"
 
+#include "zl10036.h"
+#include "mt312.h"
+
 MODULE_AUTHOR("Gerd Knorr <[email protected]> [SuSE Labs]");
 MODULE_LICENSE("GPL");
 
@@ -933,6 +936,17 @@ static struct nxt200x_config kworldatsc1
 	.demod_address    = 0x0a,
 };
 
+/* ------------------------------------------------------------------ */
+
+static struct mt312_config avertv_a700_mt312 = {
+	.demod_address = 0x0e,
+	.voltage_inverted = 1,
+};
+
+static struct zl10036_config avertv_a700_tuner = {
+	.tuner_address = 0x60,
+};
+
 /* ==================================================================
  * Core code
  */
@@ -1242,6 +1256,18 @@ static int dvb_init(struct saa7134_dev *
 			fe->ops.enable_high_lnb_voltage = md8800_set_high_voltage;
 		}
 		break;
+	case SAA7134_BOARD_AVERMEDIA_A700_PRO:
+	case SAA7134_BOARD_AVERMEDIA_A700_HYBRID:
+		dev->dvb.frontend = dvb_attach(vp310_mt312_attach,
+			&avertv_a700_mt312, &dev->i2c_adap);
+		if (dev->dvb.frontend) {
+			if (dvb_attach(zl10036_attach, dev->dvb.frontend,
+					&avertv_a700_tuner, &dev->i2c_adap) == NULL) {
+				wprintk("%s: No zl10036 found!\n",
+					__FUNCTION__);
+			}
+		}
+		break;
 	default:
 		wprintk("Huh? unknown DVB card?\n");
 		break;

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#2 lore raw

Re: [linux-dvb] a700 support (was: [patch 5/5] mt312: add attach-time setting to invert lnb-voltage (Matthias Schwarzott))

Thank you very much, Matthias. I was going to try the patch right now, however I'm finding that it doesn't apply clean to the current HG tree. This is what I'm getting:

patching file linux/drivers/media/dvb/frontends/Kconfig Hunk #1 FAILED at 368.
1 out of 1 hunk FAILED -- saving rejects to file linux/drivers/media/dvb/frontends/Kconfig.rej patching file linux/drivers/media/dvb/frontends/Makefile Hunk #1 succeeded at 23 (offset -2 lines).
patching file linux/drivers/media/dvb/frontends/zl10036.c patching file linux/drivers/media/dvb/frontends/zl10036.h patching file linux/drivers/media/video/saa7134/Kconfig patching file linux/drivers/media/video/saa7134/saa7134-cards.c Hunk #3 succeeded at 5716 (offset 42 lines).
patching file linux/drivers/media/video/saa7134/saa7134-dvb.c

I've tried to manually patch Kconfig by adding the rejected lines, but I suppose there must something I'm doing wrong: apparently it compiles fine, but saa7134-dvb is not loaded and the frontend is not being created for the card (although the card is detected and the video0 device for analog is there).

I'll apreciate any hints you could give me, I'm impatient to test this. Plus, I'm seing lately some cross posted messages regarding the chips on this cards, so maybe there's some hope for it :D

Best regards,
Eduard

2008/4/27 Matthias Schwarzott <[email protected]>:

Quoted 97 lines · Eduard Huguet
Quoted 5 lines
Quoted 5 lines

---------- Missatge reenviat ----------
From: Matthias Schwarzott <[email protected]>
To: [email protected]
Date: Sat, 12 Apr 2008 17:04:50 +0200
Subject: [linux-dvb] [patch 5/5] mt312: add attach-time setting to

invert

Quoted 26 lines
Quoted 26 lines

lnb-voltage
Add a setting to config struct for inversion of lnb-voltage. Needed for support of Avermedia A700 cards.

Index: v4l-dvb/linux/drivers/media/dvb/frontends/mt312.c
===================================================================

linux/drivers/media/dvb/frontends/mt312.c +6 -1
@@ -422,11 +422,16 @@ static int mt312_set_voltage(struct dvb_
  {
        struct mt312_state *state = fe->demodulator_priv;
        const u8 volt_tab[3] = { 0x00, 0x40, 0x00 };
+       u8 val;
 
        if (v > SEC_VOLTAGE_OFF)
                return -EINVAL;
 
-       return mt312_writereg(state, DISEQC_MODE, volt_tab[v]);
+       val = volt_tab[v];
+       if (state->config->voltage_inverted)
+               val ^= 0x40;
+
+       return mt312_writereg(state, DISEQC_MODE, val);
  }
 
Quoted 1 line

linux/drivers/media/dvb/frontends/mt312.c static int mt312_set_voltage(struct dvb_ · line 437

Quoted 1 line
linux/drivers/media/dvb/frontends/mt312.c +0 -0
  static int mt312_read_status(struct dvb_frontend *fe, fe_status_t

*s)

Quoted 13 lines
Quoted 13 lines

Index: v4l-dvb/linux/drivers/media/dvb/frontends/mt312.h
===================================================================

linux/drivers/media/dvb/frontends/mt312.h +3 -0
@@ -31,6 +31,9 @@
  struct mt312_config {
        /* the demodulator's i2c address */
        u8 demod_address;
+
+       /* inverted voltage setting */
+       int voltage_inverted:1;
  };
 
Quoted 1 line

linux/drivers/media/dvb/frontends/mt312.h line 39

Quoted 1 line
linux/drivers/media/dvb/frontends/mt312.h +0 -0
  #if defined(CONFIG_DVB_MT312) || (defined(CONFIG_DVB_MT312_MODULE)

&&

Quoted 6 lines
Quoted 2 lines

defined(MODULE))
--

Thanks for the patches. ¿Is your lastest unified diff on your page (a700_full_20080412.diff) equivalent to these patches or must they be applied separately?

Another 2 weeks later. These patches already have been applied at hg level. So
now the new remaining full patch (a700_full_20080427.diff) is to be applied
on top.

It contains a zl10036 driver and the changes to the glue code in saa7134-dvb.
zl10036 works most of the time here, but I am not fully happy with its current
design.

Open issues:
* Should set_params routine be kept spiltted as it is?
* Is bandwidth handling sane?
Now calc the needed bw by symbolrate and add 3MHz.
Datasheet suggests to start at max setting and decrease as possible after the
lock is established (using freq. offset info from demod).
* The used gain values are found by try and error and do not work for all transponders here.
The most difficult transponder here was RTL - and that now works for me with
exactly these gain settings (rfg=0, ba=1, bg=1).

Quoted 2 lines

I'll try to some tests tonight, if you have made some progress. By the

way,

Quoted 2 lines

¿could you tell me if it's better to use use_frontend=0 or 1 for saa7134-dvb module? I think that this changes the driver used for

frontend,

Quoted 1 line

but I'm not sure.

use_frontend is intended to be used for choosing between dvb-s and dvb-t or
similar if the frontend offers both exclusively. I abused this parameter to
choose between the two driver for zl10313 demod. This is no longer used, so
forget about this parameter.

Quoted 3 lines

Regards
Matthias

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#3 lore raw

Re: [linux-dvb] a700 support (was: [patch 5/5] mt312: add attach-time setting to invert lnb-voltage (Matthias Schwarzott))

Quoted 17 lines · Eduard Huguet

Thank you very much, Matthias. I was going to try the patch right now, however I'm finding that it doesn't apply clean to the current HG tree. This is what I'm getting:

patching file linux/drivers/media/dvb/frontends/Kconfig Hunk #1 FAILED at 368.
1 out of 1 hunk FAILED -- saving rejects to file linux/drivers/media/dvb/frontends/Kconfig.rej patching file linux/drivers/media/dvb/frontends/Makefile Hunk #1 succeeded at 23 (offset -2 lines).
patching file linux/drivers/media/dvb/frontends/zl10036.c patching file linux/drivers/media/dvb/frontends/zl10036.h patching file linux/drivers/media/video/saa7134/Kconfig patching file linux/drivers/media/video/saa7134/saa7134-cards.c Hunk #3 succeeded at 5716 (offset 42 lines).
patching file linux/drivers/media/video/saa7134/saa7134-dvb.c

Quoted 6 lines

I've tried to manually patch Kconfig by adding the rejected lines, but I suppose there must something I'm doing wrong: apparently it compiles fine, but saa7134-dvb is not loaded and the frontend is not being created for the card (although the card is detected and the video0 device for analog is there).

This reject is caused by the massive movement of the hybrid tuner drivers to another directory.
I solved the reject, and re-uploaded the patch.
Here it does still work.

Regards
Matthias

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#4 lore raw

Re: [linux-dvb] a700 support (was: [patch 5/5] mt312: add attach-time setting to invert lnb-voltage (Matthias Schwarzott))

Thanks! I'll try it later and let you know the results.

Regards,
Eduard

2008/4/27 Matthias Schwarzott <[email protected]>:

Quoted 26 lines · Eduard Huguet
Quoted 17 lines

Thank you very much, Matthias. I was going to try the patch right now, however I'm finding that it doesn't apply clean to the current HG tree. This is what I'm getting:

patching file linux/drivers/media/dvb/frontends/Kconfig Hunk #1 FAILED at 368.
1 out of 1 hunk FAILED -- saving rejects to file linux/drivers/media/dvb/frontends/Kconfig.rej patching file linux/drivers/media/dvb/frontends/Makefile Hunk #1 succeeded at 23 (offset -2 lines).
patching file linux/drivers/media/dvb/frontends/zl10036.c patching file linux/drivers/media/dvb/frontends/zl10036.h patching file linux/drivers/media/video/saa7134/Kconfig patching file linux/drivers/media/video/saa7134/saa7134-cards.c Hunk #3 succeeded at 5716 (offset 42 lines).
patching file linux/drivers/media/video/saa7134/saa7134-dvb.c

Quoted 2 lines

I've tried to manually patch Kconfig by adding the rejected lines, but I suppose there must something I'm doing wrong: apparently it compiles

fine,

Quoted 1 line

but saa7134-dvb is not loaded and the frontend is not being created for

the

Quoted 3 lines

card (although the card is detected and the video0 device for analog is there).

Quoted 9 lines

This reject is caused by the massive movement of the hybrid tuner drivers to
another directory.
I solved the reject, and re-uploaded the patch.
Here it does still work.

Regards
Matthias

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#5 lore raw

Re: [linux-dvb] a700 support (was: [patch 5/5] mt312: add attach-time setting to invert lnb-voltage (Matthias Schwarzott))

Well, still no luck. I'm unable to discover any channel from Astra 19.2 neither from dvbscan nor Kaffeine. For the sake of any possible diagnostics, here you have the dmesg output for the "modprobe saa7134 i2c_scan=1" command:

[40824.395017] Linux video capture interface: v2.00
[40824.427006] saa7130/34: v4l2 driver version 0.2.14 loaded
[40824.428056] saa7133[0]: found at 0000:00:09.0, rev: 209, irq: 23,
latency: 64, mmio: 0xf7ffa800
[40824.428097] saa7133[0]: subsystem: 1461:a7a1, board: Avermedia DVB-S Pro
A700 [card=140,autodetected]
[40824.428151] saa7133[0]: board init: gpio is 6f300
[40824.564594] saa7133[0]: i2c eeprom 00: 61 14 a1 a7 ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.564680] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.564741] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.564882] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.565080] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.565128] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.565173] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.565226] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.565277] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.565325] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.565374] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.565418] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.565463] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.565507] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.565578] saa7133[0]: i2c eeprom e0: 00 01 81 af ea b5 ff ff ff ff ff
ff ff ff ff ff
[40824.565630] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[40824.572529] saa7133[0]: i2c scan: found device @ 0x1c  [???]
[40824.588514] saa7133[0]: i2c scan: found device @ 0xa0  [eeprom]
[40824.619181] saa7133[0]: registered device video0 [v4l2]
[40824.620182] saa7133[0]: registered device vbi0
[40824.745393] mt312: R(126): 05
[40824.785660] mt312: R(20): 03
[40824.785694] mt312: W(20): 40
[40824.806192] mt312: R(20): 43
[40824.806227] mt312: W(20): 00
[40824.808187] zl10036_attach: tuner initialization (Zarlink ZL10036
addr=0x60) ok
[40824.808213] DVB: registering new adapter (saa7133[0])
[40824.808232] DVB: registering frontend 0 (Zarlink ZL10313 DVB-S)...
[40824.809840] mt312: W(127): 8c
[40824.812347] mt312: W(21): 80
[40824.814217] mt312: W(86): 14 12 03 02 01 00 00 00
[40824.817178] mt312: W(20): 80
[40824.819187] mt312: W(84): 80 b0
[40824.823540] mt312: W(84): 00
[40824.825158] mt312: W(85): 00
[40824.827162] mt312: W(34): b6 73
[40824.829161] mt312: W(49): 32
[40824.831146] mt312: W(96): 33
[40824.834197] mt312: W(51): 8c 98
[40824.836583] mt312: W(57): 69
[40824.838884] mt312: W(21): 80
[40824.841869] mt312: W(20): 00
[40824.844860] mt312: W(84): 0d
[40824.851210] mt312: R(127): 8c
[40824.851262] mt312: W(127): 0c
[40824.856840] mt312: R(20): 03
[40824.856884] mt312: W(20): 40
[40824.868466] mt312: R(20): 43

I have also "debug=1" for mt312 module, as you might see. I don't know if this can be also helpful, but this is the dmesg output when scanning channels from within Kaffeine:

[41068.542974] mt312: QPSK_STAT_H: 0x10, QPSK_STAT_L: 0x8a, FEC_STATUS: 0x30
[41068.547076] mt312: R(4): 10 8a 30
[41068.547118] mt312: QPSK_STAT_H: 0x10, QPSK_STAT_L: 0x8a, FEC_STATUS: 0x30
[41068.547138] mt312: mt312_set_frontend: Freq 1951000
[41068.549810] mt312: R(20): 83
[41068.549839] mt312: W(20): c0
[41068.568762] mt312: R(20): c3
[41068.568786] mt312: W(20): 80
[41068.574794] mt312: R(20): 87
[41068.574829] mt312: W(20): 80
[41068.577740] mt312: W(23): 16 00 48 40 01
[41068.579730] mt312: W(21): 40
[41068.634835] mt312: R(4): 10 8a 30
[41068.634865] mt312: QPSK_STAT_H: 0x10, QPSK_STAT_L: 0x8a, FEC_STATUS: 0x30
[41068.634880] mt312: mt312_set_frontend: Freq 1951000
[41068.636842] mt312: R(20): 83
[41068.636867] mt312: W(20): c0
[41068.657785] mt312: R(20): c3
[41068.657811] mt312: W(20): 80
[41068.661987] mt312: R(20): 83
[41068.662012] mt312: W(20): 80
[41068.663782] mt312: W(23): 16 00 48 40 01
[41068.666772] mt312: W(21): 40
[41068.671506] mt312: R(4): 10 07 30
[41068.671543] mt312: QPSK_STAT_H: 0x10, QPSK_STAT_L: 0x07, FEC_STATUS: 0x30
[41068.721382] mt312: R(4): 10 8a 30
[41068.721412] mt312: QPSK_STAT_H: 0x10, QPSK_STAT_L: 0x8a, FEC_STATUS: 0x30
[41068.721432] mt312: mt312_set_frontend: Freq 1951000
[41068.723378] mt312: R(20): 87
[41068.723399] mt312: W(20): c0
[41068.741311] mt312: R(20): c7
[41068.741336] mt312: W(20): 80
[41068.745296] mt312: R(20): 87
[41068.745316] mt312: W(20): 80
[41068.747442] mt312: W(23): 16 00 08 40 01
[41068.750296] mt312: W(21): 40
[41068.774971] mt312: R(4): 10 8a 30
[41068.775007] mt312: QPSK_STAT_H: 0x10, QPSK_STAT_L: 0x8a, FEC_STATUS: 0x30
[41068.805141] mt312: R(4): 10 8a 30
[41068.805175] mt312: QPSK_STAT_H: 0x10, QPSK_STAT_L: 0x8a, FEC_STATUS: 0x30
[41068.805191] mt312: mt312_set_frontend: Freq 1951000
[41068.807384] mt312: R(20): 83
[41068.807409] mt312: W(20): c0
[41068.828329] mt312: R(20): c3
[41068.828361] mt312: W(20): 80
[41068.834074] mt312: R(20): 87
[41068.834094] mt312: W(20): 80
[41068.836412] mt312: W(23): 16 00 08 40 01
[41068.839063] mt312: W(21): 40
[41068.844286] mt312: R(108): 95 df fe
[41068.844312] mt312: agc=00002577 err_db=-2
[41068.849075] mt312: R(9): 3e 09
[41068.857257] mt312: R(4): 10 8a 30
[41068.857287] mt312: QPSK_STAT_H: 0x10, QPSK_STAT_L: 0x8a, FEC_STATUS: 0x30
[41068.877974] mt312: R(4): 10 8a 30
[41068.878004] mt312: QPSK_STAT_H: 0x10, QPSK_STAT_L: 0x8a, FEC_STATUS: 0x30
[41068.894433] mt312: R(4): 10 8a 30
[41068.894463] mt312: QPSK_STAT_H: 0x10, QPSK_STAT_L: 0x8a, FEC_STATUS: 0x30
[41068.894479] mt312: mt312_set_frontend: Freq 1951000
[41068.896915] mt312: R(20): 83
[41068.896934] mt312: W(20): c0
[41068.916112] mt312: R(20): c7
[41068.916147] mt312: W(20): 80
[41068.920088] mt312: R(20): 87
[41068.920112] mt312: W(20): 80
[41068.922532] mt312: W(23): 16 00 48 40 01
[41068.925082] mt312: W(21): 40
[41068.979682] mt312: R(4): 10 8a 30
[41068.979716] mt312: QPSK_STAT_H: 0x10, QPSK_STAT_L: 0x8a, FEC_STATUS: 0x30
[41068.979736] mt312: mt312_set_frontend: Freq 1951000
[41068.981682] mt312: R(20): 83
[41068.981702] mt312: W(20): c0
[41069.003880] mt312: R(20): c3
[41069.003906] mt312: W(20): 80
[41069.008863] mt312: R(20): 83
[41069.008883] mt312: W(20): 80
[41069.012801] mt312: W(23): 16 00 48 40 01
[41069.015847] mt312: W(21): 40
[41069.021725] mt312: R(4): 10 07 30
[41069.021756] mt312: QPSK_STAT_H: 0x10, QPSK_STAT_L: 0x07, FEC_STATUS: 0x30
[41069.071296] mt312: R(4): 10 8a 30
[41069.071331] mt312: QPSK_STAT_H: 0x10, QPSK_STAT_L: 0x8a, FEC_STATUS: 0x30

The output was indeed longer, I've shortened it a bit because it's the same output again and again.

Best regards,
Eduard

2008/4/27 Eduard Huguet <[email protected]>:

Quoted 49 lines

Thanks! I'll try it later and let you know the results.

Regards,
Eduard

2008/4/27 Matthias Schwarzott <[email protected]>:

Quoted 38 lines · Eduard Huguet
Quoted 2 lines

Thank you very much, Matthias. I was going to try the patch right now, however I'm finding that it doesn't apply clean to the current HG

tree.

Quoted 15 lines

This is what I'm getting:

patching file linux/drivers/media/dvb/frontends/Kconfig Hunk #1 FAILED at 368.
1 out of 1 hunk FAILED -- saving rejects to file linux/drivers/media/dvb/frontends/Kconfig.rej patching file linux/drivers/media/dvb/frontends/Makefile Hunk #1 succeeded at 23 (offset -2 lines).
patching file linux/drivers/media/dvb/frontends/zl10036.c patching file linux/drivers/media/dvb/frontends/zl10036.h patching file linux/drivers/media/video/saa7134/Kconfig patching file linux/drivers/media/video/saa7134/saa7134-cards.c Hunk #3 succeeded at 5716 (offset 42 lines).
patching file linux/drivers/media/video/saa7134/saa7134-dvb.c

Quoted 1 line

I've tried to manually patch Kconfig by adding the rejected lines, but

I

Quoted 1 line

suppose there must something I'm doing wrong: apparently it compiles

fine,

Quoted 1 line

but saa7134-dvb is not loaded and the frontend is not being created

for the

Quoted 1 line

card (although the card is detected and the video0 device for analog

is

Quoted 2 lines

there).

This reject is caused by the massive movement of the hybrid tuner drivers to
another directory.
I solved the reject, and re-uploaded the patch.
Here it does still work.

Regards
Matthias

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb