Bluetooth: btmtksdio: Fix kernel oops in btmtksdio_interrupt
Subsystems (2)
PATCH RESEND 1/5 Bluetooth: btmtksdio: Fix kernel oops in btmtksdio_interrupt
From: Yake Yang <[email protected]>
Fix the following kernel oops in btmtksdio_interrrupt
[ 14.339134] btmtksdio_interrupt+0x28/0x54 [ 14.339139] process_sdio_pending_irqs+0x68/0x1a0 [ 14.339144] sdio_irq_work+0x40/0x70 [ 14.339154] process_one_work+0x184/0x39c [ 14.339160] worker_thread+0x228/0x3e8 [ 14.339168] kthread+0x148/0x3ac [ 14.339176] ret_from_fork+0x10/0x30
That happened because hdev->power_on is already called before sdio_set_drvdata which btmtksdio_interrupt handler relies on is not properly set up.
The details are shown as the below: hci_register_dev would run queue_work(hdev->req_workqueue, &hdev->power_on) as WQ_HIGHPRI workqueue_struct to complete the power-on sequeunce and thus hci_power_on may run before sdio_set_drvdata is done in btmtksdio_probe.
The hci_dev_do_open in hci_power_on would initialize the device and enable the interrupt and thus it is possible that btmtksdio_interrupt is being called right before sdio_set_drvdata is filled out.
When btmtksdio_interrupt is being called and sdio_set_drvdata is not filled , the kernel oops is going to happen because btmtksdio_interrupt access an uninitialized pointer.
--- drivers/bluetooth/btmtksdio.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/bluetooth/btmtksdio.c +2 -2
@@ -1281,6 +1281,8 @@ static int btmtksdio_probe(struct sdio_func *func, hdev->manufacturer =70 ;set_bit (HCI_QUIRK_NON_PERSISTENT_SETUP , &hdev->quirks); +sdio_set_drvdata (func, bdev); + err =hci_register_dev (hdev);if (err <0 ) {dev_err (&func->dev,"Can't register HCI device\n" );
@@ -1288,8 +1290,6 @@ static int btmtksdio_probe(struct sdio_func *func,return err; } -sdio_set_drvdata (func, bdev); -/* pm_runtime_enable would be done after the firmware is being * downloaded because the core layer probably already enables * runtime PM for this func such as the case host->caps &
Signature · 1 line
2.25.1
PATCH RESEND 2/5 Bluetooth: mt7921s: Set HCI_QUIRK_VALID_LE_STATES
From: Yake Yang <[email protected]>
The patch set HCI_QUIRK_VALID_LE_STATES to be consistent with the btusb for MT7921 and is required for the likes of experimental LE simultaneous roles.
--- drivers/bluetooth/btmtksdio.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/bluetooth/btmtksdio.c +3 -0
@@ -1070,6 +1070,9 @@ static int btmtksdio_setup(struct hci_dev *hdev) } } +/* Valid LE States quirk for MediaTek 7921 */ +set_bit (HCI_QUIRK_VALID_LE_STATES , &hdev->quirks); +break ;case 0x7663 :case 0x7668 :
Signature · 1 line
2.25.1
PATCH RESEND 3/5 Bluetooth: mt7921s: Add .get_data_path_id
In reply to [email protected]From: Yake Yang <[email protected]>
Add .get_data_path_id to fetch data_path_id for MT7921 to support HFP offload use case.
This is a preliminary patch to add the WBS support to the MT7921 driver.
--- drivers/bluetooth/btmtksdio.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-)
drivers/bluetooth/btmtksdio.c +14 -1
@@ -936,6 +936,13 @@ static int btmtksdio_mtk_reg_write(struct hci_dev *hdev, u32 reg, u32 val, u32 mreturn err; } +static int btmtksdio_get_data_path_id (struct hci_dev *hdev,__u8 *data_path_id) +{ +/* uses 1 as data path id for all the usecases */ + *data_path_id =1 ; +return 0 ; +} +static int btmtksdio_sco_setting (struct hci_dev *hdev) {const struct btmtk_sco sco_setting = {
@@ -968,7 +975,13 @@ static int btmtksdio_sco_setting(struct hci_dev *hdev)return err; val |=0x00000101 ; -return btmtksdio_mtk_reg_write (hdev,MT7921_PINMUX_1 , val, ~0 ); + err =btmtksdio_mtk_reg_write (hdev,MT7921_PINMUX_1 , val, ~0 ); +if (err <0 ) +return err; + + hdev->get_data_path_id = btmtksdio_get_data_path_id; + +return err; }static int btmtksdio_reset_setting (struct hci_dev *hdev)
Signature · 1 line
2.25.1
PATCH RESEND 4/5 Bluetooth: mt7921s: Add .btmtk_get_codec_config_data
In reply to [email protected]From: Yake Yang <[email protected]>
add .btmtk_get_codec_config_data to get codec configuration data.
In HFP offload usecase, controllers need to be set codec details before opening SCO. This callback function is used to fetch vendor specific codec config data.
This is a preliminary patch to add the WBS support to the MT7921 driver.
--- drivers/bluetooth/btmtksdio.c | 50 +++++++++++++++++++++++++++++++++++ 1 file changed, 50 insertions(+)
drivers/bluetooth/btmtksdio.c +50 -0
@@ -943,6 +943,55 @@ static int btmtksdio_get_data_path_id(struct hci_dev *hdev, __u8 *data_path_id)return 0 ; } +static int btmtksdio_get_codec_config_data (struct hci_dev *hdev, +__u8 link,struct bt_codec *codec, +__u8 *ven_len,__u8 **ven_data) +{ +int err =0 ; + +if (!ven_data || !ven_len) +return -EINVAL ; + + *ven_len =0 ; + *ven_data =NULL ; + +if (link !=ESCO_LINK ) { +bt_dev_err (hdev,"Invalid link type(%u)" , link); +return -EINVAL ; + } + + *ven_data =kmalloc (sizeof (__u8),GFP_KERNEL ); +if (!ven_data) { + err = -ENOMEM ; + goto error; + } + +/* supports only CVSD and mSBC offload codecs */ +switch (codec->id) { +case 0x02 : + **ven_data =0x00 ; +break ; +case 0x05 : + **ven_data =0x01 ; +break ; +default : + err = -EINVAL ; +bt_dev_err (hdev,"Invalid codec id(%u)" , codec->id); + goto error; + } +/* codec and its capabilities are pre-defined to ids +* preset id = 0x00 represents CVSD codec with sampling rate 8K +* preset id = 0x01 represents mSBC codec with sampling rate 16K +*/ + *ven_len =sizeof (__u8); +return err; + +error: +kfree (*ven_data); + *ven_data =NULL ; +return err; +} +static int btmtksdio_sco_setting (struct hci_dev *hdev) {const struct btmtk_sco sco_setting = {
@@ -980,6 +1029,7 @@ static int btmtksdio_sco_setting(struct hci_dev *hdev)return err; hdev->get_data_path_id = btmtksdio_get_data_path_id; + hdev->get_codec_config_data = btmtksdio_get_codec_config_data;return err; }
Signature · 1 line
2.25.1
PATCH RESEND 5/5 Bluetooth: mt7921s: Add WBS support
In reply to [email protected]From: Yake Yang <[email protected]>
It is time to add wide band speech (WBS) support.
--- drivers/bluetooth/btmtksdio.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/bluetooth/btmtksdio.c +3 -0
@@ -1123,6 +1123,9 @@ static int btmtksdio_setup(struct hci_dev *hdev)return err; } +/* Enable WBS with mSBC codec */ +set_bit (HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED , &hdev->quirks); +/* Enable GPIO reset mechanism */ if (bdev->reset) { err =btmtksdio_reset_setting (hdev);
Signature · 1 line
2.25.1
This is automated email and please do not reply to this email!
Dear submitter,
Thank you for submitting the patches to the linux bluetooth mailing list. This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=623609
---Test result---
Test Summary:
CheckPatch PASS 8.10 seconds GitLint PASS 4.93 seconds SubjectPrefix PASS 4.21 seconds BuildKernel PASS 33.61 seconds BuildKernel32 PASS 30.33 seconds Incremental Build with patchesPASS 66.22 seconds TestRunner: Setup PASS 530.30 seconds TestRunner: l2cap-tester PASS 17.09 seconds TestRunner: bnep-tester PASS 6.59 seconds TestRunner: mgmt-tester PASS 112.55 seconds TestRunner: rfcomm-tester PASS 8.57 seconds TestRunner: sco-tester PASS 8.52 seconds TestRunner: smp-tester PASS 8.35 seconds TestRunner: userchan-tester PASS 7.19 seconds
---
Regards,
Linux Bluetooth