Skip to contentSkip to conversation

iProc I2C slave mode and NIC mode

PATCH Applied Ray Jui 3 participants 16 messages Apr 3, 2019 – Apr 4, 2019

Subsystems (3)
lore
Share & tools
lore

Ray Jui

author
#0 lore raw

v6 cover iProc I2C slave mode and NIC mode

This patch series adds the following support to the iProc I2C driver:
- Increase maximum read transfer size to 255 bytes
- I2C slave mode
- Polling mode
- NIC I2C mode

This patch series is based on kernel v5.1-rc3 and available at:
https://github.com/Broadcom/arm64-linux.git
branch: i2c-slave-v6

Changes from v5:
- Address various comments from Wolfram
- Rebase to v5.1-rc3

Changes from v4:
- Add more detailed explanations in the device tree binding document changes, to address Rob's review comments

Changes from v3:
- Various minor fixes on commit messages and commits
- Rebased to v5.0-rc3

Changes from v2:
- Address Ray's review comments.

Changes from v1:
- Rebased to Linux v5.0.0-rc2

Michael Cheng (1):
i2c: iproc: Add support for more master error status

Ray Jui (1):
dt-bindings: i2c: iproc: make 'interrupts' optional

Rayagonda Kokatanur (5):
i2c: iproc: add polling support
i2c: iproc: use wrapper for read/write access
dt-bindings: i2c: iproc: add "brcm,iproc-nic-i2c" compatible string
i2c: iproc: add NIC I2C support
arm64: dts: Stingray: Add NIC i2c device node

Shreesha Rajashekar (2):
i2c: iproc: Extend I2C read up to 255 bytes
i2c: iproc: Add slave mode support

 .../bindings/i2c/brcm,iproc-i2c.txt           |  17 +-
 .../boot/dts/broadcom/stingray/stingray.dtsi  |  18 +
 drivers/i2c/busses/Kconfig                    |   1 +
 drivers/i2c/busses/i2c-bcm-iproc.c            | 758 +++++++++++++++---
 4 files changed, 662 insertions(+), 132 deletions(-)
Signature · 1 line
2.17.1
author
#1 lore raw

PATCH v6 1/9 i2c: iproc: Extend I2C read up to 255 bytes

From: Shreesha Rajashekar <[email protected]>

Add support to allow I2C master read transfer up to 255 bytes.

---
 drivers/i2c/busses/i2c-bcm-iproc.c | 96 +++++++++++++++++++++++-------
 1 file changed, 74 insertions(+), 22 deletions(-)
drivers/i2c/busses/i2c-bcm-iproc.c +74 -22
index 4c8c3bc4669c..4c31f4e178b6 100644
@@ -80,6 +80,10 @@
 
 #define I2C_TIMEOUT_MSEC             50000
 #define M_TX_RX_FIFO_SIZE            64
+#define M_RX_FIFO_MAX_THLD_VALUE     (M_TX_RX_FIFO_SIZE - 1)
+
+#define M_RX_MAX_READ_LEN            255
+#define M_RX_FIFO_THLD_VALUE         50
 
 enum bus_speed_index {
 	I2C_SPD_100K = 0,
@@ -102,17 +106,39 @@ struct bcm_iproc_i2c_dev {
 
 	/* bytes that have been transferred */
 	unsigned int tx_bytes;
+	/* bytes that have been read */
+	unsigned int rx_bytes;
+	unsigned int thld_bytes;
 };
 
 /*
  * Can be expanded in the future if more interrupt status bits are utilized
  */
-#define ISR_MASK (BIT(IS_M_START_BUSY_SHIFT) | BIT(IS_M_TX_UNDERRUN_SHIFT))
+#define ISR_MASK (BIT(IS_M_START_BUSY_SHIFT) | BIT(IS_M_TX_UNDERRUN_SHIFT)\
+		| BIT(IS_M_RX_THLD_SHIFT))
+
+static void bcm_iproc_i2c_read_valid_bytes(struct bcm_iproc_i2c_dev *iproc_i2c)
+{
+	struct i2c_msg *msg = iproc_i2c->msg;
+
+	/* Read valid data from RX FIFO */
+	while (iproc_i2c->rx_bytes < msg->len) {
+		if (!((readl(iproc_i2c->base + M_FIFO_CTRL_OFFSET) >> M_FIFO_RX_CNT_SHIFT)
+		      & M_FIFO_RX_CNT_MASK))
+			break;
+
+		msg->buf[iproc_i2c->rx_bytes] =
+			(readl(iproc_i2c->base + M_RX_OFFSET) >>
+			M_RX_DATA_SHIFT) & M_RX_DATA_MASK;
+		iproc_i2c->rx_bytes++;
+	}
+}
 
 static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
 {
 	struct bcm_iproc_i2c_dev *iproc_i2c = data;
 	u32 status = readl(iproc_i2c->base + IS_OFFSET);
+	u32 tmp;
 
 	status &= ISR_MASK;
 
@@ -136,8 +162,6 @@ static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
 
 			/* mark the last byte */
 			if (idx == msg->len - 1) {
-				u32 tmp;
-
 				val |= BIT(M_TX_WR_STATUS_SHIFT);
 
 				/*
@@ -156,6 +180,32 @@ static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
 		iproc_i2c->tx_bytes += tx_bytes;
 	}
 
+	if (status & BIT(IS_M_RX_THLD_SHIFT)) {
+		struct i2c_msg *msg = iproc_i2c->msg;
+		u32 bytes_left;
+
+		bcm_iproc_i2c_read_valid_bytes(iproc_i2c);
+		bytes_left = msg->len - iproc_i2c->rx_bytes;
+		if (bytes_left == 0) {
+			/* finished reading all data, disable rx thld event */
+			tmp = readl(iproc_i2c->base + IE_OFFSET);
+			tmp &= ~BIT(IS_M_RX_THLD_SHIFT);
+			writel(tmp, iproc_i2c->base + IE_OFFSET);
+		} else if (bytes_left < iproc_i2c->thld_bytes) {
+			/* set bytes left as threshold */
+			tmp = readl(iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+			tmp &= ~(M_FIFO_RX_THLD_MASK << M_FIFO_RX_THLD_SHIFT);
+			tmp |= (bytes_left << M_FIFO_RX_THLD_SHIFT);
+			writel(tmp, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+			iproc_i2c->thld_bytes = bytes_left;
+		}
+		/*
+		 * bytes_left >= iproc_i2c->thld_bytes,
+		 * hence no need to change the THRESHOLD SET.
+		 * It will remain as iproc_i2c->thld_bytes itself
+		 */
+	}
+
 	if (status & BIT(IS_M_START_BUSY_SHIFT)) {
 		iproc_i2c->xfer_is_done = 1;
 		complete(&iproc_i2c->done);
@@ -253,7 +303,7 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
 {
 	int ret, i;
 	u8 addr;
-	u32 val;
+	u32 val, tmp, val_intr_en;
 	unsigned int tx_bytes;
 	unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT_MSEC);
 
@@ -298,7 +348,7 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
 	 * transaction is done, i.e., the internal start_busy bit, transitions
 	 * from 1 to 0.
 	 */
-	val = BIT(IE_M_START_BUSY_SHIFT);
+	val_intr_en = BIT(IE_M_START_BUSY_SHIFT);
 
 	/*
 	 * If TX data size is larger than the TX FIFO, need to enable TX
@@ -307,9 +357,7 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
 	 */
 	if (!(msg->flags & I2C_M_RD) &&
 	    msg->len > iproc_i2c->tx_bytes)
-		val |= BIT(IE_M_TX_UNDERRUN_SHIFT);
-
-	writel(val, iproc_i2c->base + IE_OFFSET);
+		val_intr_en |= BIT(IE_M_TX_UNDERRUN_SHIFT);
 
 	/*
 	 * Now we can activate the transfer. For a read operation, specify the
@@ -317,11 +365,27 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
 	 */
 	val = BIT(M_CMD_START_BUSY_SHIFT);
 	if (msg->flags & I2C_M_RD) {
+		iproc_i2c->rx_bytes = 0;
+		if (msg->len > M_RX_FIFO_MAX_THLD_VALUE)
+			iproc_i2c->thld_bytes = M_RX_FIFO_THLD_VALUE;
+		else
+			iproc_i2c->thld_bytes = msg->len;
+
+		/* set threshold value */
+		tmp = readl(iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+		tmp &= ~(M_FIFO_RX_THLD_MASK << M_FIFO_RX_THLD_SHIFT);
+		tmp |= iproc_i2c->thld_bytes << M_FIFO_RX_THLD_SHIFT;
+		writel(tmp, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+
+		/* enable the RX threshold interrupt */
+		val_intr_en |= BIT(IE_M_RX_THLD_SHIFT);
+
 		val |= (M_CMD_PROTOCOL_BLK_RD << M_CMD_PROTOCOL_SHIFT) |
 		       (msg->len << M_CMD_RD_CNT_SHIFT);
 	} else {
 		val |= (M_CMD_PROTOCOL_BLK_WR << M_CMD_PROTOCOL_SHIFT);
 	}
+	writel(val_intr_en, iproc_i2c->base + IE_OFFSET);
 	writel(val, iproc_i2c->base + M_CMD_OFFSET);
 
 	time_left = wait_for_completion_timeout(&iproc_i2c->done, time_left);
@@ -353,17 +417,6 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
 		return ret;
 	}
 
-	/*
-	 * For a read operation, we now need to load the data from FIFO
-	 * into the memory buffer
-	 */
-	if (msg->flags & I2C_M_RD) {
-		for (i = 0; i < msg->len; i++) {
-			msg->buf[i] = (readl(iproc_i2c->base + M_RX_OFFSET) >>
-				      M_RX_DATA_SHIFT) & M_RX_DATA_MASK;
-		}
-	}
-
 	return 0;
 }
 
@@ -395,9 +448,8 @@ static const struct i2c_algorithm bcm_iproc_algo = {
 	.functionality = bcm_iproc_i2c_functionality,
 };
 
-static const struct i2c_adapter_quirks bcm_iproc_i2c_quirks = {
-	/* need to reserve one byte in the FIFO for the slave address */
-	.max_read_len = M_TX_RX_FIFO_SIZE - 1,
+static struct i2c_adapter_quirks bcm_iproc_i2c_quirks = {
+	.max_read_len = M_RX_MAX_READ_LEN,
 };
 
 static int bcm_iproc_i2c_cfg_speed(struct bcm_iproc_i2c_dev *iproc_i2c)
Signature · 1 line
2.17.1
author
#2 lore raw

PATCH v6 2/9 i2c: iproc: Add slave mode support

In reply to Ray Jui

From: Shreesha Rajashekar <[email protected]>

Add slave mode support to the iProc I2C driver.

---
 drivers/i2c/busses/Kconfig         |   1 +
 drivers/i2c/busses/i2c-bcm-iproc.c | 304 ++++++++++++++++++++++++++++-
 2 files changed, 299 insertions(+), 6 deletions(-)
drivers/i2c/busses/Kconfig +1 -0
index f8979abb9a19..a425198c9fc1 100644
@@ -425,6 +425,7 @@ config I2C_BCM_IPROC
 	tristate "Broadcom iProc I2C controller"
 	depends on ARCH_BCM_IPROC || COMPILE_TEST
 	default ARCH_BCM_IPROC
+	select I2C_SLAVE
 	help
 	  If you say yes to this option, support will be included for the
 	  Broadcom iProc I2C controller.
drivers/i2c/busses/i2c-bcm-iproc.c +298 -6

402 lines not on this page · raw message

Signature · 1 line
2.17.1
author
#3 lore raw

PATCH v6 3/9 i2c: iproc: Add support for more master error status

In reply to Ray Jui

From: Michael Cheng <[email protected]>

Add support for more master error status including FIFO underrun and RX FIFO full

---
 drivers/i2c/busses/i2c-bcm-iproc.c | 10 ++++++++++
 1 file changed, 10 insertions(+)
drivers/i2c/busses/i2c-bcm-iproc.c +10 -0
index 915c1b5aafd8..d64876cfa11c 100644
@@ -73,6 +73,8 @@
 #define M_CMD_STATUS_NACK_ADDR       0x2
 #define M_CMD_STATUS_NACK_DATA       0x3
 #define M_CMD_STATUS_TIMEOUT         0x4
+#define M_CMD_STATUS_FIFO_UNDERRUN   0x5
+#define M_CMD_STATUS_RX_FIFO_FULL    0x6
 #define M_CMD_PROTOCOL_SHIFT         9
 #define M_CMD_PROTOCOL_MASK          0xf
 #define M_CMD_PROTOCOL_BLK_WR        0x7
@@ -536,6 +538,14 @@ static int bcm_iproc_i2c_check_status(struct bcm_iproc_i2c_dev *iproc_i2c,
 		dev_dbg(iproc_i2c->device, "bus timeout\n");
 		return -ETIMEDOUT;
 
+	case M_CMD_STATUS_FIFO_UNDERRUN:
+		dev_dbg(iproc_i2c->device, "FIFO under-run\n");
+		return -ENXIO;
+
+	case M_CMD_STATUS_RX_FIFO_FULL:
+		dev_dbg(iproc_i2c->device, "RX FIFO full\n");
+		return -ETIMEDOUT;
+
 	default:
 		dev_dbg(iproc_i2c->device, "unknown error code=%d\n", val);
 
Signature · 1 line
2.17.1
author
#4 lore raw

PATCH v6 4/9 dt-bindings: i2c: iproc: make 'interrupts' optional

In reply to Ray Jui

Update the binding document to make the 'interrupts' property optional. For certain revisions of the I2C controller (e.g., iProc NIC I2C), I2C interrupt is unwired to the interrupt controller. In such case, this 'interrupts' property should be left unspecified, and driver will fall back to polling mode

---
 .../devicetree/bindings/i2c/brcm,iproc-i2c.txt        | 11 ++++++++---
 1 file changed, 8 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt +8 -3
index 81f982ccca31..7a32bf81bfa9 100644
@@ -9,9 +9,6 @@ Required properties:
     Define the base and range of the I/O address space that contain the iProc
     I2C controller registers
 
-- interrupts:
-    Should contain the I2C interrupt
-
 - clock-frequency:
     This is the I2C bus clock. Need to be either 100000 or 400000
 
@@ -21,6 +18,14 @@ Required properties:
 - #size-cells:
     Always 0
 
+Optional properties:
+
+- interrupts:
+    Should contain the I2C interrupt. For certain revisions of the I2C
+    controller, I2C interrupt is unwired to the interrupt controller. In such
+    case, this property should be left unspecified, and driver will fall back
+    to polling mode
+
 Example:
 	i2c0: i2c@18008000 {
 		compatible = "brcm,iproc-i2c";
Signature · 1 line
2.17.1
author
#5 lore raw

PATCH v6 5/9 i2c: iproc: add polling support

In reply to Ray Jui

From: Rayagonda Kokatanur <[email protected]>

Add polling support to the iProc I2C driver. Polling mode is activated when the driver fails to obtain an interrupt ID from device tree

---
 drivers/i2c/busses/i2c-bcm-iproc.c | 298 ++++++++++++++++++-----------
 1 file changed, 181 insertions(+), 117 deletions(-)
drivers/i2c/busses/i2c-bcm-iproc.c +181 -117
index d64876cfa11c..be8cd14f5ef6 100644
@@ -371,95 +371,115 @@ static void bcm_iproc_i2c_read_valid_bytes(struct bcm_iproc_i2c_dev *iproc_i2c)
 	}
 }
 
-static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
+static void bcm_iproc_i2c_send(struct bcm_iproc_i2c_dev *iproc_i2c)
 {
-	struct bcm_iproc_i2c_dev *iproc_i2c = data;
-	u32 status = readl(iproc_i2c->base + IS_OFFSET);
-	u32 tmp;
-
-
-	bool ret;
-	u32 sl_status = status & ISR_MASK_SLAVE;
-
-	if (sl_status) {
-		ret = bcm_iproc_i2c_slave_isr(iproc_i2c, sl_status);
-		if (ret)
-			return IRQ_HANDLED;
-		else
-			return IRQ_NONE;
-	}
+	struct i2c_msg *msg = iproc_i2c->msg;
+	unsigned int tx_bytes = msg->len - iproc_i2c->tx_bytes;
+	unsigned int i;
+	u32 val;
 
-	status &= ISR_MASK;
+	/* can only fill up to the FIFO size */
+	tx_bytes = min_t(unsigned int, tx_bytes, M_TX_RX_FIFO_SIZE);
+	for (i = 0; i < tx_bytes; i++) {
+		/* start from where we left over */
+		unsigned int idx = iproc_i2c->tx_bytes + i;
 
-	if (!status)
-		return IRQ_NONE;
+		val = msg->buf[idx];
 
-	/* TX FIFO is empty and we have more data to send */
-	if (status & BIT(IS_M_TX_UNDERRUN_SHIFT)) {
-		struct i2c_msg *msg = iproc_i2c->msg;
-		unsigned int tx_bytes = msg->len - iproc_i2c->tx_bytes;
-		unsigned int i;
-		u32 val;
-
-		/* can only fill up to the FIFO size */
-		tx_bytes = min_t(unsigned int, tx_bytes, M_TX_RX_FIFO_SIZE);
-		for (i = 0; i < tx_bytes; i++) {
-			/* start from where we left over */
-			unsigned int idx = iproc_i2c->tx_bytes + i;
+		/* mark the last byte */
+		if (idx == msg->len - 1) {
+			val |= BIT(M_TX_WR_STATUS_SHIFT);
 
-			val = msg->buf[idx];
-
-			/* mark the last byte */
-			if (idx == msg->len - 1) {
-				val |= BIT(M_TX_WR_STATUS_SHIFT);
+			if (iproc_i2c->irq) {
+				u32 tmp;
 
 				/*
-				 * Since this is the last byte, we should
-				 * now disable TX FIFO underrun interrupt
+				 * Since this is the last byte, we should now
+				 * disable TX FIFO underrun interrupt
 				 */
 				tmp = readl(iproc_i2c->base + IE_OFFSET);
 				tmp &= ~BIT(IE_M_TX_UNDERRUN_SHIFT);
 				writel(tmp, iproc_i2c->base + IE_OFFSET);
 			}
-
-			/* load data into TX FIFO */
-			writel(val, iproc_i2c->base + M_TX_OFFSET);
 		}
-		/* update number of transferred bytes */
-		iproc_i2c->tx_bytes += tx_bytes;
+
+		/* load data into TX FIFO */
+		writel(val, iproc_i2c->base + M_TX_OFFSET);
 	}
 
-	if (status & BIT(IS_M_RX_THLD_SHIFT)) {
-		struct i2c_msg *msg = iproc_i2c->msg;
-		u32 bytes_left;
+	/* update number of transferred bytes */
+	iproc_i2c->tx_bytes += tx_bytes;
+}
 
-		bcm_iproc_i2c_read_valid_bytes(iproc_i2c);
-		bytes_left = msg->len - iproc_i2c->rx_bytes;
-		if (bytes_left == 0) {
+static void bcm_iproc_i2c_read(struct bcm_iproc_i2c_dev *iproc_i2c)
+{
+	struct i2c_msg *msg = iproc_i2c->msg;
+	u32 bytes_left, val;
+
+	bcm_iproc_i2c_read_valid_bytes(iproc_i2c);
+	bytes_left = msg->len - iproc_i2c->rx_bytes;
+	if (bytes_left == 0) {
+		if (iproc_i2c->irq) {
 			/* finished reading all data, disable rx thld event */
-			tmp = readl(iproc_i2c->base + IE_OFFSET);
-			tmp &= ~BIT(IS_M_RX_THLD_SHIFT);
-			writel(tmp, iproc_i2c->base + IE_OFFSET);
-		} else if (bytes_left < iproc_i2c->thld_bytes) {
-			/* set bytes left as threshold */
-			tmp = readl(iproc_i2c->base + M_FIFO_CTRL_OFFSET);
-			tmp &= ~(M_FIFO_RX_THLD_MASK << M_FIFO_RX_THLD_SHIFT);
-			tmp |= (bytes_left << M_FIFO_RX_THLD_SHIFT);
-			writel(tmp, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
-			iproc_i2c->thld_bytes = bytes_left;
+			val = readl(iproc_i2c->base + IE_OFFSET);
+			val &= ~BIT(IS_M_RX_THLD_SHIFT);
+			writel(val, iproc_i2c->base + IE_OFFSET);
 		}
-		/*
-		 * bytes_left >= iproc_i2c->thld_bytes,
-		 * hence no need to change the THRESHOLD SET.
-		 * It will remain as iproc_i2c->thld_bytes itself
-		 */
+	} else if (bytes_left < iproc_i2c->thld_bytes) {
+		/* set bytes left as threshold */
+		val = readl(iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+		val &= ~(M_FIFO_RX_THLD_MASK << M_FIFO_RX_THLD_SHIFT);
+		val |= (bytes_left << M_FIFO_RX_THLD_SHIFT);
+		writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+		iproc_i2c->thld_bytes = bytes_left;
 	}
+	/*
+	 * bytes_left >= iproc_i2c->thld_bytes,
+	 * hence no need to change the THRESHOLD SET.
+	 * It will remain as iproc_i2c->thld_bytes itself
+	 */
+}
 
+static void bcm_iproc_i2c_process_m_event(struct bcm_iproc_i2c_dev *iproc_i2c,
+					  u32 status)
+{
+	/* TX FIFO is empty and we have more data to send */
+	if (status & BIT(IS_M_TX_UNDERRUN_SHIFT))
+		bcm_iproc_i2c_send(iproc_i2c);
+
+	/* RX FIFO threshold is reached and data needs to be read out */
+	if (status & BIT(IS_M_RX_THLD_SHIFT))
+		bcm_iproc_i2c_read(iproc_i2c);
+
+	/* transfer is done */
 	if (status & BIT(IS_M_START_BUSY_SHIFT)) {
 		iproc_i2c->xfer_is_done = 1;
-		complete(&iproc_i2c->done);
+		if (iproc_i2c->irq)
+			complete(&iproc_i2c->done);
+	}
+}
+
+static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
+{
+	struct bcm_iproc_i2c_dev *iproc_i2c = data;
+	u32 status = readl(iproc_i2c->base + IS_OFFSET);
+	bool ret;
+	u32 sl_status = status & ISR_MASK_SLAVE;
+
+	if (sl_status) {
+		ret = bcm_iproc_i2c_slave_isr(iproc_i2c, sl_status);
+		if (ret)
+			return IRQ_HANDLED;
+		else
+			return IRQ_NONE;
 	}
 
+	status &= ISR_MASK;
+	if (!status)
+		return IRQ_NONE;
+
+	/* process all master based events */
+	bcm_iproc_i2c_process_m_event(iproc_i2c, status);
 	writel(status, iproc_i2c->base + IS_OFFSET);
 
 	return IRQ_HANDLED;
@@ -558,14 +578,71 @@ static int bcm_iproc_i2c_check_status(struct bcm_iproc_i2c_dev *iproc_i2c,
 	}
 }
 
+static int bcm_iproc_i2c_xfer_wait(struct bcm_iproc_i2c_dev *iproc_i2c,
+				   struct i2c_msg *msg,
+				   u32 cmd)
+{
+	unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT_MSEC);
+	u32 val, status;
+	int ret;
+
+	writel(cmd, iproc_i2c->base + M_CMD_OFFSET);
+
+	if (iproc_i2c->irq) {
+		time_left = wait_for_completion_timeout(&iproc_i2c->done,
+							time_left);
+		/* disable all interrupts */
+		writel(0, iproc_i2c->base + IE_OFFSET);
+		/* read it back to flush the write */
+		readl(iproc_i2c->base + IE_OFFSET);
+		/* make sure the interrupt handler isn't running */
+		synchronize_irq(iproc_i2c->irq);
+
+	} else { /* polling mode */
+		unsigned long timeout = jiffies + time_left;
+
+		do {
+			status = readl(iproc_i2c->base + IS_OFFSET) & ISR_MASK;
+			bcm_iproc_i2c_process_m_event(iproc_i2c, status);
+			writel(status, iproc_i2c->base + IS_OFFSET);
+
+			if (time_after(jiffies, timeout)) {
+				time_left = 0;
+				break;
+			}
+
+			cpu_relax();
+			cond_resched();
+		} while (!iproc_i2c->xfer_is_done);
+	}
+
+	if (!time_left && !iproc_i2c->xfer_is_done) {
+		dev_err(iproc_i2c->device, "transaction timed out\n");
+
+		/* flush both TX/RX FIFOs */
+		val = BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT);
+		writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+		return -ETIMEDOUT;
+	}
+
+	ret = bcm_iproc_i2c_check_status(iproc_i2c, msg);
+	if (ret) {
+		/* flush both TX/RX FIFOs */
+		val = BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT);
+		writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+		return ret;
+	}
+
+	return 0;
+}
+
 static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
 					 struct i2c_msg *msg)
 {
-	int ret, i;
+	int i;
 	u8 addr;
 	u32 val, tmp, val_intr_en;
 	unsigned int tx_bytes;
-	unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT_MSEC);
 
 	/* check if bus is busy */
 	if (!!(readl(iproc_i2c->base + M_CMD_OFFSET) &
@@ -600,7 +677,9 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
 	}
 
 	/* mark as incomplete before starting the transaction */
-	reinit_completion(&iproc_i2c->done);
+	if (iproc_i2c->irq)
+		reinit_completion(&iproc_i2c->done);
+
 	iproc_i2c->xfer_is_done = 0;
 
 	/*
@@ -645,39 +724,11 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
 	} else {
 		val |= (M_CMD_PROTOCOL_BLK_WR << M_CMD_PROTOCOL_SHIFT);
 	}
-	writel(val_intr_en, iproc_i2c->base + IE_OFFSET);
-	writel(val, iproc_i2c->base + M_CMD_OFFSET);
 
-	time_left = wait_for_completion_timeout(&iproc_i2c->done, time_left);
+	if (iproc_i2c->irq)
+		writel(val_intr_en, iproc_i2c->base + IE_OFFSET);
 
-	/* disable all interrupts */
-	writel(0, iproc_i2c->base + IE_OFFSET);
-	/* read it back to flush the write */
-	readl(iproc_i2c->base + IE_OFFSET);
-
-	/* make sure the interrupt handler isn't running */
-	synchronize_irq(iproc_i2c->irq);
-
-	if (!time_left && !iproc_i2c->xfer_is_done) {
-		dev_err(iproc_i2c->device, "transaction timed out\n");
-
-		/* flush FIFOs */
-		val = (1 << M_FIFO_RX_FLUSH_SHIFT) |
-		      (1 << M_FIFO_TX_FLUSH_SHIFT);
-		writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
-		return -ETIMEDOUT;
-	}
-
-	ret = bcm_iproc_i2c_check_status(iproc_i2c, msg);
-	if (ret) {
-		/* flush both TX/RX FIFOs */
-		val = (1 << M_FIFO_RX_FLUSH_SHIFT) |
-		      (1 << M_FIFO_TX_FLUSH_SHIFT);
-		writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
-		return ret;
-	}
-
-	return 0;
+	return bcm_iproc_i2c_xfer_wait(iproc_i2c, msg, val);
 }
 
 static int bcm_iproc_i2c_xfer(struct i2c_adapter *adapter,
@@ -779,17 +830,20 @@ static int bcm_iproc_i2c_probe(struct platform_device *pdev)
 		return ret;
 
 	irq = platform_get_irq(pdev, 0);
-	if (irq <= 0) {
-		dev_err(iproc_i2c->device, "no irq resource\n");
-		return irq;
-	}
-	iproc_i2c->irq = irq;
+	if (irq > 0) {
+		ret = devm_request_irq(iproc_i2c->device, irq,
+				       bcm_iproc_i2c_isr, 0, pdev->name,
+				       iproc_i2c);
+		if (ret < 0) {
+			dev_err(iproc_i2c->device,
+				"unable to request irq %i\n", irq);
+			return ret;
+		}
 
-	ret = devm_request_irq(iproc_i2c->device, irq, bcm_iproc_i2c_isr, 0,
-			       pdev->name, iproc_i2c);
-	if (ret < 0) {
-		dev_err(iproc_i2c->device, "unable to request irq %i\n", irq);
-		return ret;
+		iproc_i2c->irq = irq;
+	} else {
+		dev_warn(iproc_i2c->device,
+			 "no irq resource, falling back to poll mode\n");
 	}
 
 	bcm_iproc_i2c_enable_disable(iproc_i2c, true);
@@ -809,10 +863,15 @@ static int bcm_iproc_i2c_remove(struct platform_device *pdev)
 {
 	struct bcm_iproc_i2c_dev *iproc_i2c = platform_get_drvdata(pdev);
 
-	/* make sure there's no pending interrupt when we remove the adapter */
-	writel(0, iproc_i2c->base + IE_OFFSET);
-	readl(iproc_i2c->base + IE_OFFSET);
-	synchronize_irq(iproc_i2c->irq);
+	if (iproc_i2c->irq) {
+		/*
+		 * Make sure there's no pending interrupt when we remove the
+		 * adapter
+		 */
+		writel(0, iproc_i2c->base + IE_OFFSET);
+		readl(iproc_i2c->base + IE_OFFSET);
+		synchronize_irq(iproc_i2c->irq);
+	}
 
 	i2c_del_adapter(&iproc_i2c->adapter);
 	bcm_iproc_i2c_enable_disable(iproc_i2c, false);
@@ -826,10 +885,15 @@ static int bcm_iproc_i2c_suspend(struct device *dev)
 {
 	struct bcm_iproc_i2c_dev *iproc_i2c = dev_get_drvdata(dev);
 
-	/* make sure there's no pending interrupt when we go into suspend */
-	writel(0, iproc_i2c->base + IE_OFFSET);
-	readl(iproc_i2c->base + IE_OFFSET);
-	synchronize_irq(iproc_i2c->irq);
+	if (iproc_i2c->irq) {
+		/*
+		 * Make sure there's no pending interrupt when we go into
+		 * suspend
+		 */
+		writel(0, iproc_i2c->base + IE_OFFSET);
+		readl(iproc_i2c->base + IE_OFFSET);
+		synchronize_irq(iproc_i2c->irq);
+	}
 
 	/* now disable the controller */
 	bcm_iproc_i2c_enable_disable(iproc_i2c, false);
Signature · 1 line
2.17.1
author
#6 lore raw

PATCH v6 6/9 i2c: iproc: use wrapper for read/write access

In reply to Ray Jui

From: Rayagonda Kokatanur <[email protected]>

Use the following wrapper for read/write access of iProc i2c registers:
u32 iproc_i2c_rd_reg(struct bcm_iproc_i2c_dev *iproc_i2c,

                     u32 offset)
void iproc_i2c_wr_reg(struct bcm_iproc_i2c_dev *iproc_i2c, u32 offset,
                      u32 val)

This preps the driver for support of indirect register access required by certain SoCs with this iProc I2C block integrated

---
 drivers/i2c/busses/i2c-bcm-iproc.c | 140 ++++++++++++++++-------------
 1 file changed, 77 insertions(+), 63 deletions(-)
drivers/i2c/busses/i2c-bcm-iproc.c +77 -63
index be8cd14f5ef6..dba1a9d925b2 100644
@@ -212,6 +212,18 @@ static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave);
 static void bcm_iproc_i2c_enable_disable(struct bcm_iproc_i2c_dev *iproc_i2c,
 					 bool enable);
 
+static inline u32 iproc_i2c_rd_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
+				   u32 offset)
+{
+	return readl(iproc_i2c->base + offset);
+}
+
+static inline void iproc_i2c_wr_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
+				    u32 offset, u32 val)
+{
+	writel(val, iproc_i2c->base + offset);
+}
+
 static void bcm_iproc_i2c_slave_init(
 	struct bcm_iproc_i2c_dev *iproc_i2c, bool need_reset)
 {
@@ -219,37 +231,37 @@ static void bcm_iproc_i2c_slave_init(
 
 	if (need_reset) {
 		/* put controller in reset */
-		val = readl(iproc_i2c->base + CFG_OFFSET);
+		val = iproc_i2c_rd_reg(iproc_i2c, CFG_OFFSET);
 		val |= BIT(CFG_RESET_SHIFT);
-		writel(val, iproc_i2c->base + CFG_OFFSET);
+		iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
 
 		/* wait 100 usec per spec */
 		udelay(100);
 
 		/* bring controller out of reset */
 		val &= ~(BIT(CFG_RESET_SHIFT));
-		writel(val, iproc_i2c->base + CFG_OFFSET);
+		iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
 	}
 
 	/* flush TX/RX FIFOs */
 	val = (BIT(S_FIFO_RX_FLUSH_SHIFT) | BIT(S_FIFO_TX_FLUSH_SHIFT));
-	writel(val, iproc_i2c->base + S_FIFO_CTRL_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, S_FIFO_CTRL_OFFSET, val);
 
 	/* Maximum slave stretch time */
-	val = readl(iproc_i2c->base + TIM_CFG_OFFSET);
+	val = iproc_i2c_rd_reg(iproc_i2c, TIM_CFG_OFFSET);
 	val &= ~(TIM_RAND_SLAVE_STRETCH_MASK << TIM_RAND_SLAVE_STRETCH_SHIFT);
 	val |= (SLAVE_CLOCK_STRETCH_TIME << TIM_RAND_SLAVE_STRETCH_SHIFT);
-	writel(val, iproc_i2c->base + TIM_CFG_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, TIM_CFG_OFFSET, val);
 
 	/* Configure the slave address */
-	val = readl(iproc_i2c->base + S_CFG_SMBUS_ADDR_OFFSET);
+	val = iproc_i2c_rd_reg(iproc_i2c, S_CFG_SMBUS_ADDR_OFFSET);
 	val |= BIT(S_CFG_EN_NIC_SMB_ADDR3_SHIFT);
 	val &= ~(S_CFG_NIC_SMB_ADDR3_MASK << S_CFG_NIC_SMB_ADDR3_SHIFT);
 	val |= (iproc_i2c->slave->addr << S_CFG_NIC_SMB_ADDR3_SHIFT);
-	writel(val, iproc_i2c->base + S_CFG_SMBUS_ADDR_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, S_CFG_SMBUS_ADDR_OFFSET, val);
 
 	/* clear all pending slave interrupts */
-	writel(ISR_MASK_SLAVE, iproc_i2c->base + IS_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, ISR_MASK_SLAVE);
 
 	/* Enable interrupt register for any READ event */
 	val = BIT(IE_S_RD_EVENT_SHIFT);
@@ -257,7 +269,7 @@ static void bcm_iproc_i2c_slave_init(
 	val |= BIT(IE_S_RX_EVENT_SHIFT);
 	/* Enable interrupt register for the Slave BUSY command */
 	val |= BIT(IE_S_START_BUSY_SHIFT);
-	writel(val, iproc_i2c->base + IE_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
 
 	iproc_i2c->xfer_dir = I2C_SLAVE_DIR_NONE;
 }
@@ -267,7 +279,7 @@ static void bcm_iproc_i2c_check_slave_status(
 {
 	u32 val;
 
-	val = readl(iproc_i2c->base + S_CMD_OFFSET);
+	val = iproc_i2c_rd_reg(iproc_i2c, S_CMD_OFFSET);
 	val = (val >> S_CMD_STATUS_SHIFT) & S_CMD_STATUS_MASK;
 
 	if (val == S_CMD_STATUS_TIMEOUT) {
@@ -290,7 +302,7 @@ static bool bcm_iproc_i2c_slave_isr(struct bcm_iproc_i2c_dev *iproc_i2c,
 
 	/* Start of transaction. check address and populate the direction */
 	if (iproc_i2c->xfer_dir == I2C_SLAVE_DIR_NONE) {
-		tmp = readl(iproc_i2c->base + S_RX_OFFSET);
+		tmp = iproc_i2c_rd_reg(iproc_i2c, S_RX_OFFSET);
 		rd_status = (tmp >> S_RX_STATUS_SHIFT) & S_RX_STATUS_MASK;
 		/* This condition checks whether the request is a new request */
 		if (((rd_status == I2C_SLAVE_RX_START) &&
@@ -316,16 +328,16 @@ static bool bcm_iproc_i2c_slave_isr(struct bcm_iproc_i2c_dev *iproc_i2c,
 		(iproc_i2c->xfer_dir == I2C_SLAVE_DIR_WRITE)) {
 		i2c_slave_event(iproc_i2c->slave,
 			I2C_SLAVE_READ_PROCESSED, &value);
-		writel(value, iproc_i2c->base + S_TX_OFFSET);
+		iproc_i2c_wr_reg(iproc_i2c, S_TX_OFFSET, value);
 
 		val = BIT(S_CMD_START_BUSY_SHIFT);
-		writel(val, iproc_i2c->base + S_CMD_OFFSET);
+		iproc_i2c_wr_reg(iproc_i2c, S_CMD_OFFSET, val);
 	}
 
 	/* write request from master */
 	if ((status & BIT(IS_S_RX_EVENT_SHIFT)) &&
 		(iproc_i2c->xfer_dir == I2C_SLAVE_DIR_READ)) {
-		val = readl(iproc_i2c->base + S_RX_OFFSET);
+		val = iproc_i2c_rd_reg(iproc_i2c, S_RX_OFFSET);
 		/* Its a write request by Master to Slave.
 		 * We read data present in receive FIFO
 		 */
@@ -348,7 +360,7 @@ static bool bcm_iproc_i2c_slave_isr(struct bcm_iproc_i2c_dev *iproc_i2c,
 	}
 
 	/* clear interrupt status */
-	writel(status, iproc_i2c->base + IS_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, status);
 
 	bcm_iproc_i2c_check_slave_status(iproc_i2c);
 	return true;
@@ -360,12 +372,12 @@ static void bcm_iproc_i2c_read_valid_bytes(struct bcm_iproc_i2c_dev *iproc_i2c)
 
 	/* Read valid data from RX FIFO */
 	while (iproc_i2c->rx_bytes < msg->len) {
-		if (!((readl(iproc_i2c->base + M_FIFO_CTRL_OFFSET) >> M_FIFO_RX_CNT_SHIFT)
+		if (!((iproc_i2c_rd_reg(iproc_i2c, M_FIFO_CTRL_OFFSET) >> M_FIFO_RX_CNT_SHIFT)
 		      & M_FIFO_RX_CNT_MASK))
 			break;
 
 		msg->buf[iproc_i2c->rx_bytes] =
-			(readl(iproc_i2c->base + M_RX_OFFSET) >>
+			(iproc_i2c_rd_reg(iproc_i2c, M_RX_OFFSET) >>
 			M_RX_DATA_SHIFT) & M_RX_DATA_MASK;
 		iproc_i2c->rx_bytes++;
 	}
@@ -397,14 +409,15 @@ static void bcm_iproc_i2c_send(struct bcm_iproc_i2c_dev *iproc_i2c)
 				 * Since this is the last byte, we should now
 				 * disable TX FIFO underrun interrupt
 				 */
-				tmp = readl(iproc_i2c->base + IE_OFFSET);
+				tmp = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
 				tmp &= ~BIT(IE_M_TX_UNDERRUN_SHIFT);
-				writel(tmp, iproc_i2c->base + IE_OFFSET);
+				iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET,
+						 tmp);
 			}
 		}
 
 		/* load data into TX FIFO */
-		writel(val, iproc_i2c->base + M_TX_OFFSET);
+		iproc_i2c_wr_reg(iproc_i2c, M_TX_OFFSET, val);
 	}
 
 	/* update number of transferred bytes */
@@ -421,16 +434,16 @@ static void bcm_iproc_i2c_read(struct bcm_iproc_i2c_dev *iproc_i2c)
 	if (bytes_left == 0) {
 		if (iproc_i2c->irq) {
 			/* finished reading all data, disable rx thld event */
-			val = readl(iproc_i2c->base + IE_OFFSET);
+			val = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
 			val &= ~BIT(IS_M_RX_THLD_SHIFT);
-			writel(val, iproc_i2c->base + IE_OFFSET);
+			iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
 		}
 	} else if (bytes_left < iproc_i2c->thld_bytes) {
 		/* set bytes left as threshold */
-		val = readl(iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+		val = iproc_i2c_rd_reg(iproc_i2c, M_FIFO_CTRL_OFFSET);
 		val &= ~(M_FIFO_RX_THLD_MASK << M_FIFO_RX_THLD_SHIFT);
 		val |= (bytes_left << M_FIFO_RX_THLD_SHIFT);
-		writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+		iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, val);
 		iproc_i2c->thld_bytes = bytes_left;
 	}
 	/*
@@ -462,7 +475,7 @@ static void bcm_iproc_i2c_process_m_event(struct bcm_iproc_i2c_dev *iproc_i2c,
 static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
 {
 	struct bcm_iproc_i2c_dev *iproc_i2c = data;
-	u32 status = readl(iproc_i2c->base + IS_OFFSET);
+	u32 status = iproc_i2c_rd_reg(iproc_i2c, IS_OFFSET);
 	bool ret;
 	u32 sl_status = status & ISR_MASK_SLAVE;
 
@@ -480,7 +493,7 @@ static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
 
 	/* process all master based events */
 	bcm_iproc_i2c_process_m_event(iproc_i2c, status);
-	writel(status, iproc_i2c->base + IS_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, status);
 
 	return IRQ_HANDLED;
 }
@@ -490,29 +503,29 @@ static int bcm_iproc_i2c_init(struct bcm_iproc_i2c_dev *iproc_i2c)
 	u32 val;
 
 	/* put controller in reset */
-	val = readl(iproc_i2c->base + CFG_OFFSET);
+	val = iproc_i2c_rd_reg(iproc_i2c, CFG_OFFSET);
 	val |= BIT(CFG_RESET_SHIFT);
 	val &= ~(BIT(CFG_EN_SHIFT));
-	writel(val, iproc_i2c->base + CFG_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
 
 	/* wait 100 usec per spec */
 	udelay(100);
 
 	/* bring controller out of reset */
 	val &= ~(BIT(CFG_RESET_SHIFT));
-	writel(val, iproc_i2c->base + CFG_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
 
 	/* flush TX/RX FIFOs and set RX FIFO threshold to zero */
 	val = (BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT));
-	writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, val);
 	/* disable all interrupts */
-	val = readl(iproc_i2c->base + IE_OFFSET);
+	val = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
 	val &= ~(IE_M_ALL_INTERRUPT_MASK <<
 			IE_M_ALL_INTERRUPT_SHIFT);
-	writel(val, iproc_i2c->base + IE_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
 
 	/* clear all pending interrupts */
-	writel(0xffffffff, iproc_i2c->base + IS_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, 0xffffffff);
 
 	return 0;
 }
@@ -522,12 +535,12 @@ static void bcm_iproc_i2c_enable_disable(struct bcm_iproc_i2c_dev *iproc_i2c,
 {
 	u32 val;
 
-	val = readl(iproc_i2c->base + CFG_OFFSET);
+	val = iproc_i2c_rd_reg(iproc_i2c, CFG_OFFSET);
 	if (enable)
 		val |= BIT(CFG_EN_SHIFT);
 	else
 		val &= ~BIT(CFG_EN_SHIFT);
-	writel(val, iproc_i2c->base + CFG_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
 }
 
 static int bcm_iproc_i2c_check_status(struct bcm_iproc_i2c_dev *iproc_i2c,
@@ -535,7 +548,7 @@ static int bcm_iproc_i2c_check_status(struct bcm_iproc_i2c_dev *iproc_i2c,
 {
 	u32 val;
 
-	val = readl(iproc_i2c->base + M_CMD_OFFSET);
+	val = iproc_i2c_rd_reg(iproc_i2c, M_CMD_OFFSET);
 	val = (val >> M_CMD_STATUS_SHIFT) & M_CMD_STATUS_MASK;
 
 	switch (val) {
@@ -586,15 +599,15 @@ static int bcm_iproc_i2c_xfer_wait(struct bcm_iproc_i2c_dev *iproc_i2c,
 	u32 val, status;
 	int ret;
 
-	writel(cmd, iproc_i2c->base + M_CMD_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, M_CMD_OFFSET, cmd);
 
 	if (iproc_i2c->irq) {
 		time_left = wait_for_completion_timeout(&iproc_i2c->done,
 							time_left);
 		/* disable all interrupts */
-		writel(0, iproc_i2c->base + IE_OFFSET);
+		iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, 0);
 		/* read it back to flush the write */
-		readl(iproc_i2c->base + IE_OFFSET);
+		iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
 		/* make sure the interrupt handler isn't running */
 		synchronize_irq(iproc_i2c->irq);
 
@@ -602,9 +615,10 @@ static int bcm_iproc_i2c_xfer_wait(struct bcm_iproc_i2c_dev *iproc_i2c,
 		unsigned long timeout = jiffies + time_left;
 
 		do {
-			status = readl(iproc_i2c->base + IS_OFFSET) & ISR_MASK;
+			status = iproc_i2c_rd_reg(iproc_i2c,
+						  IS_OFFSET) & ISR_MASK;
 			bcm_iproc_i2c_process_m_event(iproc_i2c, status);
-			writel(status, iproc_i2c->base + IS_OFFSET);
+			iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, status);
 
 			if (time_after(jiffies, timeout)) {
 				time_left = 0;
@@ -621,7 +635,7 @@ static int bcm_iproc_i2c_xfer_wait(struct bcm_iproc_i2c_dev *iproc_i2c,
 
 		/* flush both TX/RX FIFOs */
 		val = BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT);
-		writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+		iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, val);
 		return -ETIMEDOUT;
 	}
 
@@ -629,7 +643,7 @@ static int bcm_iproc_i2c_xfer_wait(struct bcm_iproc_i2c_dev *iproc_i2c,
 	if (ret) {
 		/* flush both TX/RX FIFOs */
 		val = BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT);
-		writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+		iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, val);
 		return ret;
 	}
 
@@ -645,8 +659,8 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
 	unsigned int tx_bytes;
 
 	/* check if bus is busy */
-	if (!!(readl(iproc_i2c->base + M_CMD_OFFSET) &
-	       BIT(M_CMD_START_BUSY_SHIFT))) {
+	if (!!(iproc_i2c_rd_reg(iproc_i2c,
+				M_CMD_OFFSET) & BIT(M_CMD_START_BUSY_SHIFT))) {
 		dev_warn(iproc_i2c->device, "bus is busy\n");
 		return -EBUSY;
 	}
@@ -655,7 +669,7 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
 
 	/* format and load slave address into the TX FIFO */
 	addr = i2c_8bit_addr_from_msg(msg);
-	writel(addr, iproc_i2c->base + M_TX_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, M_TX_OFFSET, addr);
 
 	/*
 	 * For a write transaction, load data into the TX FIFO. Only allow
@@ -671,7 +685,7 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
 			if (i == msg->len - 1)
 				val |= 1 << M_TX_WR_STATUS_SHIFT;
 
-			writel(val, iproc_i2c->base + M_TX_OFFSET);
+			iproc_i2c_wr_reg(iproc_i2c, M_TX_OFFSET, val);
 		}
 		iproc_i2c->tx_bytes = tx_bytes;
 	}
@@ -711,10 +725,10 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
 			iproc_i2c->thld_bytes = msg->len;
 
 		/* set threshold value */
-		tmp = readl(iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+		tmp = iproc_i2c_rd_reg(iproc_i2c, M_FIFO_CTRL_OFFSET);
 		tmp &= ~(M_FIFO_RX_THLD_MASK << M_FIFO_RX_THLD_SHIFT);
 		tmp |= iproc_i2c->thld_bytes << M_FIFO_RX_THLD_SHIFT;
-		writel(tmp, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+		iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, tmp);
 
 		/* enable the RX threshold interrupt */
 		val_intr_en |= BIT(IE_M_RX_THLD_SHIFT);
@@ -726,7 +740,7 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
 	}
 
 	if (iproc_i2c->irq)
-		writel(val_intr_en, iproc_i2c->base + IE_OFFSET);
+		iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val_intr_en);
 
 	return bcm_iproc_i2c_xfer_wait(iproc_i2c, msg, val);
 }
@@ -790,10 +804,10 @@ static int bcm_iproc_i2c_cfg_speed(struct bcm_iproc_i2c_dev *iproc_i2c)
 	}
 
 	iproc_i2c->bus_speed = bus_speed;
-	val = readl(iproc_i2c->base + TIM_CFG_OFFSET);
+	val = iproc_i2c_rd_reg(iproc_i2c, TIM_CFG_OFFSET);
 	val &= ~(1 << TIM_CFG_MODE_400_SHIFT);
 	val |= (bus_speed == 400000) << TIM_CFG_MODE_400_SHIFT;
-	writel(val, iproc_i2c->base + TIM_CFG_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, TIM_CFG_OFFSET, val);
 
 	dev_info(iproc_i2c->device, "bus set to %u Hz\n", bus_speed);
 
@@ -868,8 +882,8 @@ static int bcm_iproc_i2c_remove(struct platform_device *pdev)
 		 * Make sure there's no pending interrupt when we remove the
 		 * adapter
 		 */
-		writel(0, iproc_i2c->base + IE_OFFSET);
-		readl(iproc_i2c->base + IE_OFFSET);
+		iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, 0);
+		iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
 		synchronize_irq(iproc_i2c->irq);
 	}
 
@@ -890,8 +904,8 @@ static int bcm_iproc_i2c_suspend(struct device *dev)
 		 * Make sure there's no pending interrupt when we go into
 		 * suspend
 		 */
-		writel(0, iproc_i2c->base + IE_OFFSET);
-		readl(iproc_i2c->base + IE_OFFSET);
+		iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, 0);
+		iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
 		synchronize_irq(iproc_i2c->irq);
 	}
 
@@ -916,10 +930,10 @@ static int bcm_iproc_i2c_resume(struct device *dev)
 		return ret;
 
 	/* configure to the desired bus speed */
-	val = readl(iproc_i2c->base + TIM_CFG_OFFSET);
+	val = iproc_i2c_rd_reg(iproc_i2c, TIM_CFG_OFFSET);
 	val &= ~(1 << TIM_CFG_MODE_400_SHIFT);
 	val |= (iproc_i2c->bus_speed == 400000) << TIM_CFG_MODE_400_SHIFT;
-	writel(val, iproc_i2c->base + TIM_CFG_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, TIM_CFG_OFFSET, val);
 
 	bcm_iproc_i2c_enable_disable(iproc_i2c, true);
 
@@ -963,15 +977,15 @@ static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave)
 	iproc_i2c->slave = NULL;
 
 	/* disable all slave interrupts */
-	tmp = readl(iproc_i2c->base + IE_OFFSET);
+	tmp = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
 	tmp &= ~(IE_S_ALL_INTERRUPT_MASK <<
 			IE_S_ALL_INTERRUPT_SHIFT);
-	writel(tmp, iproc_i2c->base + IE_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, tmp);
 
 	/* Erase the slave address programmed */
-	tmp = readl(iproc_i2c->base + S_CFG_SMBUS_ADDR_OFFSET);
+	tmp = iproc_i2c_rd_reg(iproc_i2c, S_CFG_SMBUS_ADDR_OFFSET);
 	tmp &= ~BIT(S_CFG_EN_NIC_SMB_ADDR3_SHIFT);
-	writel(tmp, iproc_i2c->base + S_CFG_SMBUS_ADDR_OFFSET);
+	iproc_i2c_wr_reg(iproc_i2c, S_CFG_SMBUS_ADDR_OFFSET, tmp);
 
 	return 0;
 }
Signature · 1 line
2.17.1
author
#7 lore raw

PATCH v6 7/9 dt-bindings: i2c: iproc: add "brcm,iproc-nic-i2c" compatible string

In reply to Ray Jui

From: Rayagonda Kokatanur <[email protected]>

Update iProc I2C binding document to add new compatible string "brcm,iproc-nic-i2c". Optional property "brcm,ape-hsls-addr-mask" is also added that allows configuration of the host view into the APE's address for "brcm,iproc-nic-i2c"

---
 Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt +5 -1
index 7a32bf81bfa9..d12cc33cca6c 100644
@@ -3,7 +3,7 @@ Broadcom iProc I2C controller
 Required properties:
 
 - compatible:
-    Must be "brcm,iproc-i2c"
+    Must be "brcm,iproc-i2c" or "brcm,iproc-nic-i2c"
 
 - reg:
     Define the base and range of the I/O address space that contain the iProc
@@ -26,6 +26,10 @@ Optional properties:
     case, this property should be left unspecified, and driver will fall back
     to polling mode
 
+- brcm,ape-hsls-addr-mask:
+    Required for "brcm,iproc-nic-i2c". Host view of address mask into the
+    'APE' co-processor. Value must be unsigned, 32-bit
+
 Example:
 	i2c0: i2c@18008000 {
 		compatible = "brcm,iproc-i2c";
Signature · 1 line
2.17.1
author
#8 lore raw

PATCH v6 8/9 i2c: iproc: add NIC I2C support

In reply to Ray Jui

From: Rayagonda Kokatanur <[email protected]>

Add NIC I2C support to the iProc I2C driver. Access to the NIC I2C base registers requires going through the IDM wrapper to map into the NIC's address space

---
 drivers/i2c/busses/i2c-bcm-iproc.c | 80 ++++++++++++++++++++++++++++--
 1 file changed, 75 insertions(+), 5 deletions(-)
drivers/i2c/busses/i2c-bcm-iproc.c +75 -5
index dba1a9d925b2..562942d0c05c 100644
@@ -17,9 +17,11 @@
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 
+#define IDM_CTRL_DIRECT_OFFSET       0x00
 #define CFG_OFFSET                   0x00
 #define CFG_RESET_SHIFT              31
 #define CFG_EN_SHIFT                 30
@@ -174,11 +176,23 @@ enum bus_speed_index {
 	I2C_SPD_400K,
 };
 
+enum bcm_iproc_i2c_type {
+	IPROC_I2C,
+	IPROC_I2C_NIC
+};
+
 struct bcm_iproc_i2c_dev {
 	struct device *device;
+	enum bcm_iproc_i2c_type type;
 	int irq;
 
 	void __iomem *base;
+	void __iomem *idm_base;
+
+	u32 ape_addr_mask;
+
+	/* lock for indirect access through IDM */
+	spinlock_t idm_lock;
 
 	struct i2c_adapter adapter;
 	unsigned int bus_speed;
@@ -215,13 +229,33 @@ static void bcm_iproc_i2c_enable_disable(struct bcm_iproc_i2c_dev *iproc_i2c,
 static inline u32 iproc_i2c_rd_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
 				   u32 offset)
 {
-	return readl(iproc_i2c->base + offset);
+	u32 val;
+
+	if (iproc_i2c->idm_base) {
+		spin_lock(&iproc_i2c->idm_lock);
+		writel(iproc_i2c->ape_addr_mask,
+		       iproc_i2c->idm_base + IDM_CTRL_DIRECT_OFFSET);
+		val = readl(iproc_i2c->base + offset);
+		spin_unlock(&iproc_i2c->idm_lock);
+	} else {
+		val = readl(iproc_i2c->base + offset);
+	}
+
+	return val;
 }
 
 static inline void iproc_i2c_wr_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
 				    u32 offset, u32 val)
 {
-	writel(val, iproc_i2c->base + offset);
+	if (iproc_i2c->idm_base) {
+		spin_lock(&iproc_i2c->idm_lock);
+		writel(iproc_i2c->ape_addr_mask,
+		       iproc_i2c->idm_base + IDM_CTRL_DIRECT_OFFSET);
+		writel(val, iproc_i2c->base + offset);
+		spin_unlock(&iproc_i2c->idm_lock);
+	} else {
+		writel(val, iproc_i2c->base + offset);
+	}
 }
 
 static void bcm_iproc_i2c_slave_init(
@@ -765,10 +799,15 @@ static int bcm_iproc_i2c_xfer(struct i2c_adapter *adapter,
 
 static uint32_t bcm_iproc_i2c_functionality(struct i2c_adapter *adap)
 {
-	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_SLAVE;
+	u32 val = I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+
+	if (adap->algo->reg_slave)
+		val |= I2C_FUNC_SLAVE;
+
+	return val;
 }
 
-static const struct i2c_algorithm bcm_iproc_algo = {
+static struct i2c_algorithm bcm_iproc_algo = {
 	.master_xfer = bcm_iproc_i2c_xfer,
 	.functionality = bcm_iproc_i2c_functionality,
 	.reg_slave = bcm_iproc_i2c_reg_slave,
@@ -828,6 +867,8 @@ static int bcm_iproc_i2c_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, iproc_i2c);
 	iproc_i2c->device = &pdev->dev;
+	iproc_i2c->type =
+		(enum bcm_iproc_i2c_type)of_device_get_match_data(&pdev->dev);
 	init_completion(&iproc_i2c->done);
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -835,6 +876,29 @@ static int bcm_iproc_i2c_probe(struct platform_device *pdev)
 	if (IS_ERR(iproc_i2c->base))
 		return PTR_ERR(iproc_i2c->base);
 
+	if (iproc_i2c->type == IPROC_I2C_NIC) {
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+		iproc_i2c->idm_base = devm_ioremap_resource(iproc_i2c->device,
+							    res);
+		if (IS_ERR(iproc_i2c->idm_base))
+			return PTR_ERR(iproc_i2c->idm_base);
+
+		ret = of_property_read_u32(iproc_i2c->device->of_node,
+					   "brcm,ape-hsls-addr-mask",
+					   &iproc_i2c->ape_addr_mask);
+		if (ret < 0) {
+			dev_err(iproc_i2c->device,
+				"'brcm,ape-hsls-addr-mask' missing\n");
+			return -EINVAL;
+		}
+
+		spin_lock_init(&iproc_i2c->idm_lock);
+
+		/* no slave support */
+		bcm_iproc_algo.reg_slave = NULL;
+		bcm_iproc_algo.unreg_slave = NULL;
+	}
+
 	ret = bcm_iproc_i2c_init(iproc_i2c);
 	if (ret)
 		return ret;
@@ -991,7 +1055,13 @@ static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave)
 }
 
 static const struct of_device_id bcm_iproc_i2c_of_match[] = {
-	{ .compatible = "brcm,iproc-i2c" },
+	{
+		.compatible = "brcm,iproc-i2c",
+		.data = (int *)IPROC_I2C,
+	}, {
+		.compatible = "brcm,iproc-nic-i2c",
+		.data = (int *)IPROC_I2C_NIC,
+	},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, bcm_iproc_i2c_of_match);
Signature · 1 line
2.17.1
author
#9 lore raw

PATCH v6 9/9 arm64: dts: Stingray: Add NIC i2c device node

In reply to Ray Jui

From: Rayagonda Kokatanur <[email protected]>

Add NIC i2c device node.

---
 .../boot/dts/broadcom/stingray/stingray.dtsi   | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi +18 -0
index 35c4670c00d1..69306fbd14b4 100644
@@ -612,4 +612,22 @@
 			status = "disabled";
 		};
 	};
+
+	nic-hsls {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0  0x0 0x7fffffff>;
+
+		nic_i2c0: i2c@60826100 {
+			compatible = "brcm,iproc-nic-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x60826100 0x100>,
+			      <0x60e00408 0x1000>;
+			brcm,ape-hsls-addr-mask = <0x03400000>;
+			clock-frequency = <100000>;
+			status = "disabled";
+		};
+	};
 };
Signature · 1 line
2.17.1
#11 lore raw
In reply to Ray Jui
Quoted 6 lines · Ray Jui

This patch series adds the following support to the iProc I2C driver:
- Increase maximum read transfer size to 255 bytes
- I2C slave mode
- Polling mode
- NIC I2C mode

Quoted 6 lines

This patch series is based on kernel v5.1-rc3 and available at:
https://github.com/Broadcom/arm64-linux.git
branch: i2c-slave-v6

Changes from v5:
- Address various comments from Wolfram

In the future, please write in detail what you changed. I review so many patches that I can't recall all my comments on every patch.

That being said, all patches applied to for-next, thanks!

Can be fixed incrementally, my code checkers complain about:

CPPCHECK
drivers/i2c/busses/i2c-bcm-iproc.c:720:14: warning: Shifting signed 32-bit value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]

    val |= 1 << M_TX_WR_STATUS_SHIFT;
             ^
drivers/i2c/busses/i2c-bcm-iproc.c:847:13: warning: Shifting signed 32-bit value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]
 val &= ~(1 << TIM_CFG_MODE_400_SHIFT);
            ^

drivers/i2c/busses/i2c-bcm-iproc.c:998:13: warning: Shifting signed 32-bit value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]
val &= ~(1 << TIM_CFG_MODE_400_SHIFT);

author
#12 lore raw

Hi Wolfram,

Quoted 11 lines · Wolfram Sang
Quoted 10 lines · Ray Jui

This patch series adds the following support to the iProc I2C driver:
- Increase maximum read transfer size to 255 bytes
- I2C slave mode
- Polling mode
- NIC I2C mode

This patch series is based on kernel v5.1-rc3 and available at:
https://github.com/Broadcom/arm64-linux.git
branch: i2c-slave-v6

Quoted 6 lines
Quoted 2 lines

Changes from v5:
- Address various comments from Wolfram

In the future, please write in detail what you changed. I review so many patches that I can't recall all my comments on every patch.

Sure will do next time.

Quoted 2 lines

That being said, all patches applied to for-next, thanks!

Thanks!

Quoted 4 lines

Can be fixed incrementally, my code checkers complain about:

CPPCHECK
drivers/i2c/busses/i2c-bcm-iproc.c:720:14: warning: Shifting signed 32-bit value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]

Quoted 8 lines
    val |= 1 << M_TX_WR_STATUS_SHIFT;
             ^
drivers/i2c/busses/i2c-bcm-iproc.c:847:13: warning: Shifting signed 32-bit value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]
 val &= ~(1 << TIM_CFG_MODE_400_SHIFT);
            ^

drivers/i2c/busses/i2c-bcm-iproc.c:998:13: warning: Shifting signed 32-bit value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]
val &= ~(1 << TIM_CFG_MODE_400_SHIFT);

I'll submit an incremental patch to fix the above warnings. I think we can convert all '1 << XXX' syntax in this driver to 'BIT(XXX)'. It will fix all of the above warnings and make the code more readable.

Thanks,

Ray

#13 lore raw
In reply to Wolfram Sang
Quoted 11 lines · Wolfram Sang
Quoted 10 lines · Ray Jui

This patch series adds the following support to the iProc I2C driver:
- Increase maximum read transfer size to 255 bytes
- I2C slave mode
- Polling mode
- NIC I2C mode

This patch series is based on kernel v5.1-rc3 and available at:
https://github.com/Broadcom/arm64-linux.git
branch: i2c-slave-v6

Quoted 7 lines
Quoted 2 lines

Changes from v5:
- Address various comments from Wolfram

In the future, please write in detail what you changed. I review so many patches that I can't recall all my comments on every patch.

That being said, all patches applied to for-next, thanks!

OK, I will drop patch #9 from my queue then, thanks.

Quoted 19 lines

Can be fixed incrementally, my code checkers complain about:

CPPCHECK
drivers/i2c/busses/i2c-bcm-iproc.c:720:14: warning: Shifting signed 32-bit value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]

    val |= 1 << M_TX_WR_STATUS_SHIFT;
             ^
drivers/i2c/busses/i2c-bcm-iproc.c:847:13: warning: Shifting signed 32-bit value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]
 val &= ~(1 << TIM_CFG_MODE_400_SHIFT);
            ^

drivers/i2c/busses/i2c-bcm-iproc.c:998:13: warning: Shifting signed 32-bit value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]
val &= ~(1 << TIM_CFG_MODE_400_SHIFT);

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Signature · 1 line
Florian
#14 lore raw
Quoted 15 lines · Florian Fainelli
Quoted 14 lines · Wolfram Sang
Quoted 12 lines · Ray Jui

This patch series adds the following support to the iProc I2C driver:
- Increase maximum read transfer size to 255 bytes
- I2C slave mode
- Polling mode
- NIC I2C mode

This patch series is based on kernel v5.1-rc3 and available at:
https://github.com/Broadcom/arm64-linux.git
branch: i2c-slave-v6

Changes from v5:
- Address various comments from Wolfram

Quoted 6 lines
Quoted 4 lines

In the future, please write in detail what you changed. I review so many patches that I can't recall all my comments on every patch.

That being said, all patches applied to for-next, thanks!

OK, I will drop patch #9 from my queue then, thanks.

Sorry, I meant patches 1-8 applied, assuming patch 9 was already taken. I usually don't pick up DTS patches, so I'd be happy if you could keep #9 in your tree.

#15 lore raw
Quoted 19 lines · Wolfram Sang
Quoted 18 lines · Florian Fainelli
Quoted 17 lines · Wolfram Sang
Quoted 6 lines · Ray Jui

This patch series adds the following support to the iProc I2C driver:
- Increase maximum read transfer size to 255 bytes
- I2C slave mode
- Polling mode
- NIC I2C mode

Quoted 6 lines

This patch series is based on kernel v5.1-rc3 and available at:
https://github.com/Broadcom/arm64-linux.git
branch: i2c-slave-v6

Changes from v5:
- Address various comments from Wolfram

In the future, please write in detail what you changed. I review so many patches that I can't recall all my comments on every patch.

Quoted 7 lines
Quoted 3 lines
Quoted 1 line

That being said, all patches applied to for-next, thanks!

OK, I will drop patch #9 from my queue then, thanks.

Sorry, I meant patches 1-8 applied, assuming patch 9 was already taken. I usually don't pick up DTS patches, so I'd be happy if you could keep #9 in your tree.

Now applied and pushed out, not a problem, thanks!

Signature · 1 line
Florian