Skip to contentSkip to conversation

i2c: mv64xxx: Allow continuing after read

RFC In review Sam Edwards 1 participant 1 message Mar 20, 2024

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

RFC v2 4/5 i2c: mv64xxx: Allow continuing after read

The current FSM does not check the send_stop flag when completing a read message; it just assumes any read message is always the end of the transfer. This means subsequent messages go unprocessed, with no error code to indicate otherwise.

Fixing this requires that the FSM check the send_stop flag and issue the SEND_RESTART action instead of stop, but there are only two RCV_* variants, one for receive-and-continue and one for receive-and-stop. We could add another variant, however, the new FSM from the previous patch makes it pretty clear that the RCV_* variants aren't really full actions in their own respect, since they both implement the same observable functionality as another action, just with an added read from the data register first.

Therefore, convert the receive actions to a flag that can be set, allowing any action to have an "...and also read" variant. The FSM can then just use the plain SEND_RESTART action, but OR-in the flag, to represent "read a byte, finish this message, go to the next message."

---
 drivers/i2c/busses/i2c-mv64xxx.c | 47 +++++++++++---------------------
 1 file changed, 16 insertions(+), 31 deletions(-)
drivers/i2c/busses/i2c-mv64xxx.c +16 -31
index 3ae74160001d..6a205cca603a 100644
@@ -116,9 +116,9 @@ enum mv64xxx_i2c_action {
 	MV64XXX_I2C_ACTION_SEND_ADDR_1,
 	MV64XXX_I2C_ACTION_SEND_ADDR_2,
 	MV64XXX_I2C_ACTION_SEND_DATA,
-	MV64XXX_I2C_ACTION_RCV_DATA,
-	MV64XXX_I2C_ACTION_RCV_DATA_STOP,
 	MV64XXX_I2C_ACTION_SEND_STOP,
+
+	MV64XXX_I2C_ACTION_RECEIVE = 0x80,
 };
 
 struct mv64xxx_i2c_regs {
@@ -395,16 +395,15 @@ mv64xxx_i2c_fsm(struct mv64xxx_i2c_data *drv_data, u32 status)
 
 	case MV64XXX_I2C_STATE_READ:
 		if (drv_data->bytes_left == 0) {
-			if (prev_state == MV64XXX_I2C_STATE_READ)
-				drv_data->action = MV64XXX_I2C_ACTION_RCV_DATA_STOP;
-			else
+			if (drv_data->send_stop || drv_data->aborting) {
 				drv_data->action = MV64XXX_I2C_ACTION_SEND_STOP;
-			drv_data->state = MV64XXX_I2C_STATE_IDLE;
+				drv_data->state = MV64XXX_I2C_STATE_IDLE;
+			} else {
+				drv_data->action = MV64XXX_I2C_ACTION_SEND_RESTART;
+				drv_data->state = MV64XXX_I2C_STATE_RESTART;
+			}
 		} else {
-			if (prev_state == MV64XXX_I2C_STATE_READ)
-				drv_data->action = MV64XXX_I2C_ACTION_RCV_DATA;
-			else
-				drv_data->action = MV64XXX_I2C_ACTION_CONTINUE;
+			drv_data->action = MV64XXX_I2C_ACTION_CONTINUE;
 
 			/*
 			 * bytes_left counts the remaining read actions to send
@@ -419,6 +418,8 @@ mv64xxx_i2c_fsm(struct mv64xxx_i2c_data *drv_data, u32 status)
 			if (drv_data->bytes_left == 0)
 				drv_data->cntl_bits &= ~MV64XXX_I2C_REG_CONTROL_ACK;
 		}
+		if (prev_state == MV64XXX_I2C_STATE_READ)
+			drv_data->action |= MV64XXX_I2C_ACTION_RECEIVE;
 		break;
 
 	case MV64XXX_I2C_STATE_WRITE:
@@ -457,6 +458,11 @@ static void mv64xxx_i2c_send_start(struct mv64xxx_i2c_data *drv_data)
 static void
 mv64xxx_i2c_do_action(struct mv64xxx_i2c_data *drv_data)
 {
+	if (drv_data->action & MV64XXX_I2C_ACTION_RECEIVE)
+		drv_data->msg->buf[drv_data->byte_posn++] =
+			readl(drv_data->reg_base + drv_data->reg_offsets.data);
+	drv_data->action &= ~MV64XXX_I2C_ACTION_RECEIVE;
+
 	switch(drv_data->action) {
 	case MV64XXX_I2C_ACTION_SEND_RESTART:
 		/* We should only get here if we have further messages */
@@ -503,27 +509,6 @@ mv64xxx_i2c_do_action(struct mv64xxx_i2c_data *drv_data)
 			drv_data->reg_base + drv_data->reg_offsets.control);
 		break;
 
-	case MV64XXX_I2C_ACTION_RCV_DATA:
-		drv_data->msg->buf[drv_data->byte_posn++] =
-			readl(drv_data->reg_base + drv_data->reg_offsets.data);
-		writel(drv_data->cntl_bits,
-			drv_data->reg_base + drv_data->reg_offsets.control);
-		break;
-
-	case MV64XXX_I2C_ACTION_RCV_DATA_STOP:
-		drv_data->msg->buf[drv_data->byte_posn++] =
-			readl(drv_data->reg_base + drv_data->reg_offsets.data);
-		if (!drv_data->atomic)
-			drv_data->cntl_bits &= ~MV64XXX_I2C_REG_CONTROL_INTEN;
-		writel(drv_data->cntl_bits | MV64XXX_I2C_REG_CONTROL_STOP,
-			drv_data->reg_base + drv_data->reg_offsets.control);
-		drv_data->block = 0;
-		if (drv_data->errata_delay)
-			udelay(5);
-
-		wake_up(&drv_data->waitq);
-		break;
-
 	case MV64XXX_I2C_ACTION_INVALID:
 	default:
 		dev_err(&drv_data->adapter.dev,
Signature · 1 line
2.43.2