arm: pmu-overflow-interrupt: Increase count values
PATCH 1/1 arm: pmu-overflow-interrupt: Increase count values
On some hardware, some pmu-overflow-interrupt failures can be observed. Although the even counter overflows, the interrupt is not seen as expected. This happens in the subtest after "promote to 64-b" comment. After analysis, the PMU overflow interrupt actually hits, ie. kvm_pmu_perf_overflow() gets called and KVM_REQ_IRQ_PENDING is set, as expected. However the PMCR.E is reset by the handle_exit path, at kvm_pmu_handle_pmcr() before the next guest entry and kvm_pmu_flush_hwstate/kvm_pmu_update_state subsequent call. There, since the enable bit has been reset, kvm_pmu_update_state() does not inject the interrupt into the guest.
This does not seem to be a KVM bug but rather an unfortunate scenario where the test disables the PMCR.E too closely to the advent of the overflow interrupt.
Since it looks like a benign and inlikely case, let's resize the number of iterations to prevent the PMCR enable bit from being resetted at the same time as the actual overflow event.
COUNT_INT is introduced, arbitrarily set to 1000 iterations and is used in this test.
--- arm/pmu.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)
arm/pmu.c +8 -7
@@ -66,6 +66,7 @@#define PRE_OVERFLOW_64 0xFFFFFFFFFFFFFFF0ULL#define COUNT 250#define MARGIN 100 +#define COUNT_INT 1000/* * PRE_OVERFLOW2 is set so that 1st @COUNT iterations do not * produce 32b overflow and 2nd @COUNT iterations do. To accommodate
@@ -978,13 +979,13 @@ static void test_overflow_interrupt(bool overflow_at_64bits)/* interrupts are disabled (PMINTENSET_EL1 == 0) */ -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);report (expect_interrupts (0 ),"no overflow interrupt after preset" );set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);isb (); -for (i =0 ; i <100 ; i++) +for (i =0 ; i <COUNT_INT ; i++)write_sysreg (0x2 , pmswinc_el0);isb ();
@@ -1002,15 +1003,15 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_sysreg (ALL_SET_32 , pmintenset_el1);isb (); -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);isb (); -for (i =0 ; i <100 ; i++) +for (i =0 ; i <COUNT_INT ; i++)write_sysreg (0x3 , pmswinc_el0); -mem_access_loop (addr,200 , pmu.pmcr_ro); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro);report_info ("overflow=0x%lx" ,read_sysreg (pmovsclr_el0));report (expect_interrupts (0x3 ),"overflow interrupts expected on #0 and #1" );
@@ -1029,7 +1030,7 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_regn_el0 (pmevtyper,1 ,CHAIN |PMEVTYPER_EXCLUDE_EL0 );write_regn_el0 (pmevcntr,0 , pre_overflow);isb (); -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);report (expect_interrupts (0x1 ),"expect overflow interrupt" );/* overflow on odd counter */
@@ -1037,7 +1038,7 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_regn_el0 (pmevcntr,0 , pre_overflow);write_regn_el0 (pmevcntr,1 , all_set);isb (); -mem_access_loop (addr,400 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);if (overflow_at_64bits) {report (expect_interrupts (0x1 ),"expect overflow interrupt on even counter" );
Signature · 1 line
2.41.0
Hi Eric,
Quoted 11 lines · Eric Auger
On some hardware, some pmu-overflow-interrupt failures can be observed. Although the even counter overflows, the interrupt is not seen as expected. This happens in the subtest after "promote to 64-b" comment. After analysis, the PMU overflow interrupt actually hits, ie.
kvm_pmu_perf_overflow()gets called andKVM_REQ_IRQ_PENDINGis set, as expected. However the PMCR.E is reset by thehandle_exitpath, atkvm_pmu_handle_pmcr()before the next guest entry and kvm_pmu_flush_hwstate/kvm_pmu_update_state subsequent call. There, since the enable bit has been reset,kvm_pmu_update_state()does not inject the interrupt into the guest.
Quoted 3 lines
This does not seem to be a KVM bug but rather an unfortunate scenario where the test disables the PMCR.E too closely to the advent of the overflow interrupt.
If I understand correctly, the KVM PMU, after receiving the hardware PMUIRQ and before injecting the interrupt, checks that the PMU is enabled according to the pseudocode for the function CheckForPMUOverflow(). CheckForPMUOverflow() returns false because PMCR_EL1.E is 0, so the KVM PMU decides not to inject the interrupt.
Is that correct?
Changing the number of SW_INCR events might not be optimal - for example, COUNT_INT > 100 might hide an error that otherwise would have been triggered if the number of events were 100. Not very likely, but still a possibility.
Another approach would be to wait for a set amount of time for the CPU to take the interrupt. There's something similar in timer.c::{test_timer_tval(), timer_do_wfi()}.
Thanks,
Alex
Quoted 82 lines
Since it looks like a benign and inlikely case, let's resize the number of iterations to prevent the PMCR enable bit from being resetted at the same time as the actual overflow event.
COUNT_INTis introduced, arbitrarily set to 1000 iterations and is used in this test.Reported-by Jan Richter <[email protected]>Signed-off-by Eric Auger <[email protected]>--- arm/pmu.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)arm/pmu.c +8
-7@@ -66,6 +66,7 @@#define PRE_OVERFLOW_64 0xFFFFFFFFFFFFFFF0ULL#define COUNT 250#define MARGIN 100 +#define COUNT_INT 1000/* * PRE_OVERFLOW2 is set so that 1st @COUNT iterations do not * produce 32b overflow and 2nd @COUNT iterations do. To accommodate @@ -978,13 +979,13 @@ static void test_overflow_interrupt(bool overflow_at_64bits)/* interrupts are disabled (PMINTENSET_EL1 == 0) */ -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);report (expect_interrupts (0 ),"no overflow interrupt after preset" );set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);isb (); -for (i =0 ; i <100 ; i++) +for (i =0 ; i <COUNT_INT ; i++)write_sysreg (0x2 , pmswinc_el0);isb ();@@ -1002,15 +1003,15 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_sysreg (ALL_SET_32 , pmintenset_el1);isb (); -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);isb (); -for (i =0 ; i <100 ; i++) +for (i =0 ; i <COUNT_INT ; i++)write_sysreg (0x3 , pmswinc_el0); -mem_access_loop (addr,200 , pmu.pmcr_ro); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro);report_info ("overflow=0x%lx" ,read_sysreg (pmovsclr_el0));report (expect_interrupts (0x3 ),"overflow interrupts expected on #0 and #1" );@@ -1029,7 +1030,7 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_regn_el0 (pmevtyper,1 ,CHAIN |PMEVTYPER_EXCLUDE_EL0 );write_regn_el0 (pmevcntr,0 , pre_overflow);isb (); -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);report (expect_interrupts (0x1 ),"expect overflow interrupt" );/* overflow on odd counter */ @@ -1037,7 +1038,7 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_regn_el0 (pmevcntr,0 , pre_overflow);write_regn_el0 (pmevcntr,1 , all_set);isb (); -mem_access_loop (addr,400 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);if (overflow_at_64bits) {report (expect_interrupts (0x1 ),"expect overflow interrupt on even counter" );Signature · 1 line
2.41.0
Hi Alexandru,
Quoted 17 lines · Alexandru Elisei
Hi Eric,
Quoted 11 lines · Eric Auger
On some hardware, some pmu-overflow-interrupt failures can be observed. Although the even counter overflows, the interrupt is not seen as expected. This happens in the subtest after "promote to 64-b" comment. After analysis, the PMU overflow interrupt actually hits, ie.
kvm_pmu_perf_overflow()gets called andKVM_REQ_IRQ_PENDINGis set, as expected. However the PMCR.E is reset by thehandle_exitpath, atkvm_pmu_handle_pmcr()before the next guest entry and kvm_pmu_flush_hwstate/kvm_pmu_update_state subsequent call. There, since the enable bit has been reset,kvm_pmu_update_state()does not inject the interrupt into the guest.Quoted 3 lines
This does not seem to be a KVM bug but rather an unfortunate scenario where the test disables the PMCR.E too closely to the advent of the overflow interrupt.
Quoted 7 lines
If I understand correctly, the KVM PMU, after receiving the hardware PMUIRQ and before injecting the interrupt, checks that the PMU is enabled according to the pseudocode for the function
CheckForPMUOverflow().CheckForPMUOverflow()returns false because PMCR_EL1.E is 0, so the KVM PMU decides not to inject the interrupt.Is that correct?
Yes that's correct
Quoted 4 lines
Changing the number of
SW_INCRevents might not be optimal - for example,COUNT_INT> 100 might hide an error that otherwise would have been triggered if the number of events were 100. Not very likely, but still a possibility.
I also changed the COUNT for SW_INCR events to unify the code. However this is not strictly necessary to fix the issue I encounter. I can revert that change if you prefer.
Quoted 4 lines
Another approach would be to wait for a set amount of time for the CPU to take the interrupt. There's something similar in timer.c::{test_timer_tval(),
timer_do_wfi()}.
you're right. However this would urge me to have a separate asm code that loops with wfi after doing the mem_access loop. I am not sure this is worth the candle here?
Thanks!
Eric
Quoted 85 lines
Thanks,
AlexQuoted 81 lines
Since it looks like a benign and inlikely case, let's resize the number of iterations to prevent the PMCR enable bit from being resetted at the same time as the actual overflow event.
COUNT_INTis introduced, arbitrarily set to 1000 iterations and is used in this test.Reported-by Jan Richter <[email protected]>Signed-off-by Eric Auger <[email protected]>--- arm/pmu.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)arm/pmu.c +8
-7@@ -66,6 +66,7 @@#define PRE_OVERFLOW_64 0xFFFFFFFFFFFFFFF0ULL#define COUNT 250#define MARGIN 100 +#define COUNT_INT 1000/* * PRE_OVERFLOW2 is set so that 1st @COUNT iterations do not * produce 32b overflow and 2nd @COUNT iterations do. To accommodate @@ -978,13 +979,13 @@ static void test_overflow_interrupt(bool overflow_at_64bits)/* interrupts are disabled (PMINTENSET_EL1 == 0) */ -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);report (expect_interrupts (0 ),"no overflow interrupt after preset" );set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);isb (); -for (i =0 ; i <100 ; i++) +for (i =0 ; i <COUNT_INT ; i++)write_sysreg (0x2 , pmswinc_el0);isb ();@@ -1002,15 +1003,15 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_sysreg (ALL_SET_32 , pmintenset_el1);isb (); -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);isb (); -for (i =0 ; i <100 ; i++) +for (i =0 ; i <COUNT_INT ; i++)write_sysreg (0x3 , pmswinc_el0); -mem_access_loop (addr,200 , pmu.pmcr_ro); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro);report_info ("overflow=0x%lx" ,read_sysreg (pmovsclr_el0));report (expect_interrupts (0x3 ),"overflow interrupts expected on #0 and #1" );@@ -1029,7 +1030,7 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_regn_el0 (pmevtyper,1 ,CHAIN |PMEVTYPER_EXCLUDE_EL0 );write_regn_el0 (pmevcntr,0 , pre_overflow);isb (); -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);report (expect_interrupts (0x1 ),"expect overflow interrupt" );/* overflow on odd counter */ @@ -1037,7 +1038,7 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_regn_el0 (pmevcntr,0 , pre_overflow);write_regn_el0 (pmevcntr,1 , all_set);isb (); -mem_access_loop (addr,400 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);if (overflow_at_64bits) {report (expect_interrupts (0x1 ),"expect overflow interrupt on even counter" );Signature · 1 line
2.41.0
Quoted 28 lines · Eric Auger
Hi Alexandru,
Quoted 17 lines · Alexandru Elisei
Hi Eric,
Quoted 11 lines · Eric Auger
On some hardware, some pmu-overflow-interrupt failures can be observed. Although the even counter overflows, the interrupt is not seen as expected. This happens in the subtest after "promote to 64-b" comment. After analysis, the PMU overflow interrupt actually hits, ie.
kvm_pmu_perf_overflow()gets called andKVM_REQ_IRQ_PENDINGis set, as expected. However the PMCR.E is reset by thehandle_exitpath, atkvm_pmu_handle_pmcr()before the next guest entry and kvm_pmu_flush_hwstate/kvm_pmu_update_state subsequent call. There, since the enable bit has been reset,kvm_pmu_update_state()does not inject the interrupt into the guest.Quoted 3 lines
This does not seem to be a KVM bug but rather an unfortunate scenario where the test disables the PMCR.E too closely to the advent of the overflow interrupt.
Quoted 7 lines
If I understand correctly, the KVM PMU, after receiving the hardware PMUIRQ and before injecting the interrupt, checks that the PMU is enabled according to the pseudocode for the function
CheckForPMUOverflow().CheckForPMUOverflow()returns false because PMCR_EL1.E is 0, so the KVM PMU decides not to inject the interrupt.Is that correct?
Quoted 8 lines
Yes that's correct
Quoted 4 lines
Changing the number of
SW_INCRevents might not be optimal - for example,COUNT_INT> 100 might hide an error that otherwise would have been triggered if the number of events were 100. Not very likely, but still a possibility.I also changed the COUNT for
SW_INCRevents to unify the code. However this is not strictly necessary to fix the issue I encounter. I can revert that change if you prefer.
I don't understand how that would solve the problem. As I see it, the problem is that PMCR_EL1.E is cleared too fast after the PMU asserts the interrupt on overflow, not the time it takes to get to the overflow condition (i.e, the number of iterations mem_access_loop() does).
Quoted 7 lines
Quoted 4 lines
Another approach would be to wait for a set amount of time for the CPU to take the interrupt. There's something similar in timer.c::{test_timer_tval(),
timer_do_wfi()}.you're right. However this would urge me to have a separate asm code that loops with wfi after doing the
mem_accessloop. I am not sure this is worth the candle here?
I think plain C would work, I was thinking something like this:
arm/pmu.c +17 -0
@@ -979,6 +979,23 @@ static void test_overflow_interrupt(bool overflow_at_64bits)/* interrupts are disabled (PMINTENSET_EL1 == 0) */ mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); + +if (!expect_interrupts (0 )) { +for (i =0 ; i <10 ; i++) { +local_irq_disable (); +if (expect_interrupts (0 )) { +local_irq_enable (); +break ; + } +report_info ("waiting for interrupt..." ); +wfi (); +local_irq_enable (); +if (expect_interrupts (0 )) +break ; +mdelay (100 ); + } + } +report (expect_interrupts (0 ),"no overflow interrupt after preset" );set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);
Can be cleaned up by moving it to separate function, etc. Has the downside that it may performs extra memory accesses in expect_interrupts(). Your choice.
By the way, pmu_stats is not declared volatile, which means that the compiler is free to optimize accesses to the struct by caching previously read values in registers. Have you tried declaring it as volatile, in case that fixes the issues you were seeing?
If you do decide to go with the above suggestion, I strongly suggest pmu_stats is declared as volatile, otherwise the compiler will likely end up not reading from memory on every iteration.
Thanks,
Alex
Quoted 90 lines
Thanks!
Eric
Quoted 85 lines
Thanks,
AlexQuoted 81 lines
Since it looks like a benign and inlikely case, let's resize the number of iterations to prevent the PMCR enable bit from being resetted at the same time as the actual overflow event.
COUNT_INTis introduced, arbitrarily set to 1000 iterations and is used in this test.Reported-by Jan Richter <[email protected]>Signed-off-by Eric Auger <[email protected]>--- arm/pmu.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)arm/pmu.c +8
-7@@ -66,6 +66,7 @@#define PRE_OVERFLOW_64 0xFFFFFFFFFFFFFFF0ULL#define COUNT 250#define MARGIN 100 +#define COUNT_INT 1000/* * PRE_OVERFLOW2 is set so that 1st @COUNT iterations do not * produce 32b overflow and 2nd @COUNT iterations do. To accommodate @@ -978,13 +979,13 @@ static void test_overflow_interrupt(bool overflow_at_64bits)/* interrupts are disabled (PMINTENSET_EL1 == 0) */ -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);report (expect_interrupts (0 ),"no overflow interrupt after preset" );set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);isb (); -for (i =0 ; i <100 ; i++) +for (i =0 ; i <COUNT_INT ; i++)write_sysreg (0x2 , pmswinc_el0);isb ();@@ -1002,15 +1003,15 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_sysreg (ALL_SET_32 , pmintenset_el1);isb (); -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);isb (); -for (i =0 ; i <100 ; i++) +for (i =0 ; i <COUNT_INT ; i++)write_sysreg (0x3 , pmswinc_el0); -mem_access_loop (addr,200 , pmu.pmcr_ro); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro);report_info ("overflow=0x%lx" ,read_sysreg (pmovsclr_el0));report (expect_interrupts (0x3 ),"overflow interrupts expected on #0 and #1" );@@ -1029,7 +1030,7 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_regn_el0 (pmevtyper,1 ,CHAIN |PMEVTYPER_EXCLUDE_EL0 );write_regn_el0 (pmevcntr,0 , pre_overflow);isb (); -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);report (expect_interrupts (0x1 ),"expect overflow interrupt" );/* overflow on odd counter */ @@ -1037,7 +1038,7 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_regn_el0 (pmevcntr,0 , pre_overflow);write_regn_el0 (pmevcntr,1 , all_set);isb (); -mem_access_loop (addr,400 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);if (overflow_at_64bits) {report (expect_interrupts (0x1 ),"expect overflow interrupt on even counter" );Signature · 1 line
2.41.0
Quoted 32 lines · Alexandru Elisei
Quoted 31 lines · Eric Auger
Hi Alexandru,
Quoted 17 lines · Alexandru Elisei
Hi Eric,
Quoted 11 lines · Eric Auger
On some hardware, some pmu-overflow-interrupt failures can be observed. Although the even counter overflows, the interrupt is not seen as expected. This happens in the subtest after "promote to 64-b" comment. After analysis, the PMU overflow interrupt actually hits, ie.
kvm_pmu_perf_overflow()gets called andKVM_REQ_IRQ_PENDINGis set, as expected. However the PMCR.E is reset by thehandle_exitpath, atkvm_pmu_handle_pmcr()before the next guest entry and kvm_pmu_flush_hwstate/kvm_pmu_update_state subsequent call. There, since the enable bit has been reset,kvm_pmu_update_state()does not inject the interrupt into the guest.Quoted 3 lines
This does not seem to be a KVM bug but rather an unfortunate scenario where the test disables the PMCR.E too closely to the advent of the overflow interrupt.
Quoted 7 lines
If I understand correctly, the KVM PMU, after receiving the hardware PMUIRQ and before injecting the interrupt, checks that the PMU is enabled according to the pseudocode for the function
CheckForPMUOverflow().CheckForPMUOverflow()returns false because PMCR_EL1.E is 0, so the KVM PMU decides not to inject the interrupt.Is that correct?
Yes that's correct
Quoted 3 lines
Changing the number of
SW_INCRevents might not be optimal - for example,COUNT_INT> 100 might hide an error that otherwise would have been triggered if the number of events were 100. Not very likely, but still a possibility.
Quoted 7 lines
Quoted 3 lines
I also changed the COUNT for
SW_INCRevents to unify the code. However this is not strictly necessary to fix the issue I encounter. I can revert that change if you prefer.I don't understand how that would solve the problem. As I see it, the problem is that PMCR_EL1.E is cleared too fast after the PMU asserts the interrupt on overflow, not the time it takes to get to the overflow condition (i.e, the number of iterations
mem_access_loop()does).
sorry I did not make my point clear. Indeed wrt SW_INCR overflow testing I do not intend to fix any issue by this change. I just intended to use the same number of iterations as for mem_access. So I will revert that change.
Quoted 14 lines
Quoted 7 lines
Quoted 4 lines
Another approach would be to wait for a set amount of time for the CPU to take the interrupt. There's something similar in timer.c::{test_timer_tval(),
timer_do_wfi()}.you're right. However this would urge me to have a separate asm code that loops with wfi after doing the
mem_accessloop. I am not sure this is worth the candle here?I think plain C would work, I was thinking something like this:
arm/pmu.c +0
-0
arm/pmu.c static void test_overflow_interrupt(bool overflow_at_64bits) · line 981
Quoted 3 lines
arm/pmu.c +0
-0@@ -979,6 +979,23 @@ static void test_overflow_interrupt(bool overflow_at_64bits)/* interrupts are disabled (PMINTENSET_EL1 == 0) */ mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);
Currently PMCR_E is reset by mem_access_loop() (at msr pmcr_el0, xzr\n"). so if we want to introduce a delay between the overflow interrupt and the PMCR.E disable, we need to either add extra MEM_ACCESS or do wfi within mem_access_loop()
Or we do something like what you suggest below and reset the PMCR_E afterwards with the downside to add extra code execution accounted by the PMU. I would prefer to avoid that since the purpose of having the asm code was to "master" what we measure.
Quoted 21 lines
arm/pmu.c +17
-0+ +if (!expect_interrupts (0 )) { +for (i =0 ; i <10 ; i++) { +local_irq_disable (); +if (expect_interrupts (0 )) { +local_irq_enable (); +break ; + } +report_info ("waiting for interrupt..." ); +wfi (); +local_irq_enable (); +if (expect_interrupts (0 )) +break ; +mdelay (100 ); + } + } +report (expect_interrupts (0 ),"no overflow interrupt after preset" );set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);
Quoted 7 lines
Can be cleaned up by moving it to separate function, etc. Has the downside that it may performs extra memory accesses in
expect_interrupts(). Your choice.By the way,
pmu_statsis not declared volatile, which means that the compiler is free to optimize accesses to the struct by caching previously read values in registers. Have you tried declaring it as volatile, in case that fixes the issues you were seeing?
In my case it won't fix the issue because the stats match what happens but your suggestion makes total sense in general.
I will add that.
Eric
Quoted 94 lines
If you do decide to go with the above suggestion, I strongly suggest
pmu_statsis declared as volatile, otherwise the compiler will likely end up not reading from memory on every iteration.Thanks,
AlexQuoted 87 lines
Thanks!
Eric
Quoted 84 lines
Thanks,
AlexQuoted 81 lines
Since it looks like a benign and inlikely case, let's resize the number of iterations to prevent the PMCR enable bit from being resetted at the same time as the actual overflow event.
COUNT_INTis introduced, arbitrarily set to 1000 iterations and is used in this test.Reported-by Jan Richter <[email protected]>Signed-off-by Eric Auger <[email protected]>--- arm/pmu.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)arm/pmu.c +8
-7@@ -66,6 +66,7 @@#define PRE_OVERFLOW_64 0xFFFFFFFFFFFFFFF0ULL#define COUNT 250#define MARGIN 100 +#define COUNT_INT 1000/* * PRE_OVERFLOW2 is set so that 1st @COUNT iterations do not * produce 32b overflow and 2nd @COUNT iterations do. To accommodate @@ -978,13 +979,13 @@ static void test_overflow_interrupt(bool overflow_at_64bits)/* interrupts are disabled (PMINTENSET_EL1 == 0) */ -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);report (expect_interrupts (0 ),"no overflow interrupt after preset" );set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);isb (); -for (i =0 ; i <100 ; i++) +for (i =0 ; i <COUNT_INT ; i++)write_sysreg (0x2 , pmswinc_el0);isb ();@@ -1002,15 +1003,15 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_sysreg (ALL_SET_32 , pmintenset_el1);isb (); -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);isb (); -for (i =0 ; i <100 ; i++) +for (i =0 ; i <COUNT_INT ; i++)write_sysreg (0x3 , pmswinc_el0); -mem_access_loop (addr,200 , pmu.pmcr_ro); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro);report_info ("overflow=0x%lx" ,read_sysreg (pmovsclr_el0));report (expect_interrupts (0x3 ),"overflow interrupts expected on #0 and #1" );@@ -1029,7 +1030,7 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_regn_el0 (pmevtyper,1 ,CHAIN |PMEVTYPER_EXCLUDE_EL0 );write_regn_el0 (pmevcntr,0 , pre_overflow);isb (); -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);report (expect_interrupts (0x1 ),"expect overflow interrupt" );/* overflow on odd counter */ @@ -1037,7 +1038,7 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_regn_el0 (pmevcntr,0 , pre_overflow);write_regn_el0 (pmevcntr,1 , all_set);isb (); -mem_access_loop (addr,400 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);if (overflow_at_64bits) {report (expect_interrupts (0x1 ),"expect overflow interrupt on even counter" );Signature · 1 line
2.41.0
Hi,
Quoted 63 lines · Eric Auger
Quoted 32 lines · Alexandru Elisei
Quoted 31 lines · Eric Auger
Hi Alexandru,
Quoted 17 lines · Alexandru Elisei
Hi Eric,
Quoted 11 lines · Eric Auger
On some hardware, some pmu-overflow-interrupt failures can be observed. Although the even counter overflows, the interrupt is not seen as expected. This happens in the subtest after "promote to 64-b" comment. After analysis, the PMU overflow interrupt actually hits, ie.
kvm_pmu_perf_overflow()gets called andKVM_REQ_IRQ_PENDINGis set, as expected. However the PMCR.E is reset by thehandle_exitpath, atkvm_pmu_handle_pmcr()before the next guest entry and kvm_pmu_flush_hwstate/kvm_pmu_update_state subsequent call. There, since the enable bit has been reset,kvm_pmu_update_state()does not inject the interrupt into the guest.Quoted 3 lines
This does not seem to be a KVM bug but rather an unfortunate scenario where the test disables the PMCR.E too closely to the advent of the overflow interrupt.
Quoted 7 lines
If I understand correctly, the KVM PMU, after receiving the hardware PMUIRQ and before injecting the interrupt, checks that the PMU is enabled according to the pseudocode for the function
CheckForPMUOverflow().CheckForPMUOverflow()returns false because PMCR_EL1.E is 0, so the KVM PMU decides not to inject the interrupt.Is that correct?
Yes that's correct
Quoted 3 lines
Changing the number of
SW_INCRevents might not be optimal - for example,COUNT_INT> 100 might hide an error that otherwise would have been triggered if the number of events were 100. Not very likely, but still a possibility.Quoted 7 lines
Quoted 3 lines
I also changed the COUNT for
SW_INCRevents to unify the code. However this is not strictly necessary to fix the issue I encounter. I can revert that change if you prefer.I don't understand how that would solve the problem. As I see it, the problem is that PMCR_EL1.E is cleared too fast after the PMU asserts the interrupt on overflow, not the time it takes to get to the overflow condition (i.e, the number of iterations
mem_access_loop()does).sorry I did not make my point clear. Indeed wrt
SW_INCRoverflow testing I do not intend to fix any issue by this change. I just intended to use the same number of iterations as formem_access. So I will revert that change.Quoted 16 lines
Quoted 7 lines
Quoted 4 lines
Another approach would be to wait for a set amount of time for the CPU to take the interrupt. There's something similar in timer.c::{test_timer_tval(),
timer_do_wfi()}.you're right. However this would urge me to have a separate asm code that loops with wfi after doing the
mem_accessloop. I am not sure this is worth the candle here?I think plain C would work, I was thinking something like this:
arm/pmu.c +0
-0@@ -979,6 +979,23 @@ static void test_overflow_interrupt(bool overflow_at_64bits)/* interrupts are disabled (PMINTENSET_EL1 == 0) */
Quoted 5 lines
arm/pmu.c static void test_overflow_interrupt(bool overflow_at_64bits) · line 981
Quoted 1 line
arm/pmu.c +0
-0mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);Currently
PMCR_Eis reset bymem_access_loop()(at msrpmcr_el0, xzr\n"). so if we want to introduce a delay between the overflow interrupt and the PMCR.E disable, we need to either add extraMEM_ACCESSor do wfi withinmem_access_loop()
Sorry, missed that.
Quoted 4 lines
Or we do something like what you suggest below and reset the
PMCR_Eafterwards with the downside to add extra code execution accounted by the PMU. I would prefer to avoid that since the purpose of having the asm code was to "master" what we measure.
Just an idea, we could re-enable the PMU in the C function right after the mem_loop(), which will get trapped and KVM will probably inject the interrupt because according to CheckForPMUOverflow() the PMUIRQ should be asserted. This is just a theory, haven't tested this and haven't looked at the KVM code.
I still think we should have the wait loop after re-enabling the PMU, just so the test is architecturally compliant (i.e., interrupts are not delivered instantaneously after the device asserts the interrupt to the GIC), but that could be left as an exercise for another patch.
Thanks,
Alex
Quoted 129 lines
Quoted 21 lines
arm/pmu.c +17
-0+ +if (!expect_interrupts (0 )) { +for (i =0 ; i <10 ; i++) { +local_irq_disable (); +if (expect_interrupts (0 )) { +local_irq_enable (); +break ; + } +report_info ("waiting for interrupt..." ); +wfi (); +local_irq_enable (); +if (expect_interrupts (0 )) +break ; +mdelay (100 ); + } + } +report (expect_interrupts (0 ),"no overflow interrupt after preset" );set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);Quoted 7 lines
Can be cleaned up by moving it to separate function, etc. Has the downside that it may performs extra memory accesses in
expect_interrupts(). Your choice.By the way,
pmu_statsis not declared volatile, which means that the compiler is free to optimize accesses to the struct by caching previously read values in registers. Have you tried declaring it as volatile, in case that fixes the issues you were seeing?In my case it won't fix the issue because the stats match what happens but your suggestion makes total sense in general.
I will add that.
Eric
Quoted 94 lines
If you do decide to go with the above suggestion, I strongly suggest
pmu_statsis declared as volatile, otherwise the compiler will likely end up not reading from memory on every iteration.Thanks,
AlexQuoted 87 lines
Thanks!
Eric
Quoted 84 lines
Thanks,
AlexQuoted 81 lines
Since it looks like a benign and inlikely case, let's resize the number of iterations to prevent the PMCR enable bit from being resetted at the same time as the actual overflow event.
COUNT_INTis introduced, arbitrarily set to 1000 iterations and is used in this test.Reported-by Jan Richter <[email protected]>Signed-off-by Eric Auger <[email protected]>--- arm/pmu.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)arm/pmu.c +8
-7@@ -66,6 +66,7 @@#define PRE_OVERFLOW_64 0xFFFFFFFFFFFFFFF0ULL#define COUNT 250#define MARGIN 100 +#define COUNT_INT 1000/* * PRE_OVERFLOW2 is set so that 1st @COUNT iterations do not * produce 32b overflow and 2nd @COUNT iterations do. To accommodate @@ -978,13 +979,13 @@ static void test_overflow_interrupt(bool overflow_at_64bits)/* interrupts are disabled (PMINTENSET_EL1 == 0) */ -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);report (expect_interrupts (0 ),"no overflow interrupt after preset" );set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);isb (); -for (i =0 ; i <100 ; i++) +for (i =0 ; i <COUNT_INT ; i++)write_sysreg (0x2 , pmswinc_el0);isb ();@@ -1002,15 +1003,15 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_sysreg (ALL_SET_32 , pmintenset_el1);isb (); -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);isb (); -for (i =0 ; i <100 ; i++) +for (i =0 ; i <COUNT_INT ; i++)write_sysreg (0x3 , pmswinc_el0); -mem_access_loop (addr,200 , pmu.pmcr_ro); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro);report_info ("overflow=0x%lx" ,read_sysreg (pmovsclr_el0));report (expect_interrupts (0x3 ),"overflow interrupts expected on #0 and #1" );@@ -1029,7 +1030,7 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_regn_el0 (pmevtyper,1 ,CHAIN |PMEVTYPER_EXCLUDE_EL0 );write_regn_el0 (pmevcntr,0 , pre_overflow);isb (); -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);report (expect_interrupts (0x1 ),"expect overflow interrupt" );/* overflow on odd counter */ @@ -1037,7 +1038,7 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_regn_el0 (pmevcntr,0 , pre_overflow);write_regn_el0 (pmevcntr,1 , all_set);isb (); -mem_access_loop (addr,400 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);if (overflow_at_64bits) {report (expect_interrupts (0x1 ),"expect overflow interrupt on even counter" );Signature · 1 line
2.41.0
Hi Alexandru,
Quoted 74 lines · Alexandru Elisei
Hi,
Quoted 60 lines · Eric Auger
Quoted 32 lines · Alexandru Elisei
Quoted 31 lines · Eric Auger
Hi Alexandru,
Quoted 17 lines · Alexandru Elisei
Hi Eric,
Quoted 11 lines · Eric Auger
On some hardware, some pmu-overflow-interrupt failures can be observed. Although the even counter overflows, the interrupt is not seen as expected. This happens in the subtest after "promote to 64-b" comment. After analysis, the PMU overflow interrupt actually hits, ie.
kvm_pmu_perf_overflow()gets called andKVM_REQ_IRQ_PENDINGis set, as expected. However the PMCR.E is reset by thehandle_exitpath, atkvm_pmu_handle_pmcr()before the next guest entry and kvm_pmu_flush_hwstate/kvm_pmu_update_state subsequent call. There, since the enable bit has been reset,kvm_pmu_update_state()does not inject the interrupt into the guest.Quoted 3 lines
This does not seem to be a KVM bug but rather an unfortunate scenario where the test disables the PMCR.E too closely to the advent of the overflow interrupt.
Quoted 7 lines
If I understand correctly, the KVM PMU, after receiving the hardware PMUIRQ and before injecting the interrupt, checks that the PMU is enabled according to the pseudocode for the function
CheckForPMUOverflow().CheckForPMUOverflow()returns false because PMCR_EL1.E is 0, so the KVM PMU decides not to inject the interrupt.Is that correct?
Yes that's correct
Quoted 3 lines
Changing the number of
SW_INCRevents might not be optimal - for example,COUNT_INT> 100 might hide an error that otherwise would have been triggered if the number of events were 100. Not very likely, but still a possibility.Quoted 7 lines
Quoted 3 lines
I also changed the COUNT for
SW_INCRevents to unify the code. However this is not strictly necessary to fix the issue I encounter. I can revert that change if you prefer.I don't understand how that would solve the problem. As I see it, the problem is that PMCR_EL1.E is cleared too fast after the PMU asserts the interrupt on overflow, not the time it takes to get to the overflow condition (i.e, the number of iterations
mem_access_loop()does).sorry I did not make my point clear. Indeed wrt
SW_INCRoverflow testing I do not intend to fix any issue by this change. I just intended to use the same number of iterations as formem_access. So I will revert that change.Quoted 15 lines
Quoted 6 lines
Quoted 3 lines
Another approach would be to wait for a set amount of time for the CPU to take the interrupt. There's something similar in timer.c::{test_timer_tval(),
timer_do_wfi()}.you're right. However this would urge me to have a separate asm code that loops with wfi after doing the
mem_accessloop. I am not sure this is worth the candle here?I think plain C would work, I was thinking something like this:
arm/pmu.c +0
-0@@ -979,6 +979,23 @@ static void test_overflow_interrupt(bool overflow_at_64bits)/* interrupts are disabled (PMINTENSET_EL1 == 0) */ Quoted 5 lines
arm/pmu.c static void test_overflow_interrupt(bool overflow_at_64bits) · line 981
Quoted 1 line
arm/pmu.c +0
-0mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);Currently
PMCR_Eis reset bymem_access_loop()(at msrpmcr_el0, xzr\n"). so if we want to introduce a delay between the overflow interrupt and the PMCR.E disable, we need to either add extraMEM_ACCESSor do wfi withinmem_access_loop()Sorry, missed that.
Quoted 4 lines
Or we do something like what you suggest below and reset the
PMCR_Eafterwards with the downside to add extra code execution accounted by the PMU. I would prefer to avoid that since the purpose of having the asm code was to "master" what we measure.
Quoted 5 lines
Just an idea, we could re-enable the PMU in the C function right after the
mem_loop(), which will get trapped and KVM will probably inject the interrupt because according toCheckForPMUOverflow()the PMUIRQ should be asserted. This is just a theory, haven't tested this and haven't looked at the KVM code.
Yes it does but you still need to leave time for the guest to aknowledge the interrupt, with intrusiveness wrt counting.
Adding traces or even adding the volatile pmu_stats change the timings and sometimes the error cannot be encountered anymore. Adding the wait loop would probably be nicer but it also disturbs the PMU counting so I am inclined to keep things simple and just increase the mem_access_loop count to let the IRQ being processed by KVM with PMU enable bit still set. This does not change the functionality of the test and this fixes failures on Amberwing.
Thanks
Eric
Quoted 136 lines
I still think we should have the wait loop after re-enabling the PMU, just so the test is architecturally compliant (i.e., interrupts are not delivered instantaneously after the device asserts the interrupt to the GIC), but that could be left as an exercise for another patch.
Thanks,
AlexQuoted 127 lines
Quoted 21 lines
arm/pmu.c +17
-0+ +if (!expect_interrupts (0 )) { +for (i =0 ; i <10 ; i++) { +local_irq_disable (); +if (expect_interrupts (0 )) { +local_irq_enable (); +break ; + } +report_info ("waiting for interrupt..." ); +wfi (); +local_irq_enable (); +if (expect_interrupts (0 )) +break ; +mdelay (100 ); + } + } +report (expect_interrupts (0 ),"no overflow interrupt after preset" );set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);Quoted 7 lines
Can be cleaned up by moving it to separate function, etc. Has the downside that it may performs extra memory accesses in
expect_interrupts(). Your choice.By the way,
pmu_statsis not declared volatile, which means that the compiler is free to optimize accesses to the struct by caching previously read values in registers. Have you tried declaring it as volatile, in case that fixes the issues you were seeing?In my case it won't fix the issue because the stats match what happens but your suggestion makes total sense in general.
I will add that.
Eric
Quoted 93 lines
If you do decide to go with the above suggestion, I strongly suggest
pmu_statsis declared as volatile, otherwise the compiler will likely end up not reading from memory on every iteration.Thanks,
AlexQuoted 87 lines
Thanks!
Eric
Quoted 84 lines
Thanks,
AlexQuoted 81 lines
Since it looks like a benign and inlikely case, let's resize the number of iterations to prevent the PMCR enable bit from being resetted at the same time as the actual overflow event.
COUNT_INTis introduced, arbitrarily set to 1000 iterations and is used in this test.Reported-by Jan Richter <[email protected]>Signed-off-by Eric Auger <[email protected]>--- arm/pmu.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)arm/pmu.c +8
-7@@ -66,6 +66,7 @@#define PRE_OVERFLOW_64 0xFFFFFFFFFFFFFFF0ULL#define COUNT 250#define MARGIN 100 +#define COUNT_INT 1000/* * PRE_OVERFLOW2 is set so that 1st @COUNT iterations do not * produce 32b overflow and 2nd @COUNT iterations do. To accommodate @@ -978,13 +979,13 @@ static void test_overflow_interrupt(bool overflow_at_64bits)/* interrupts are disabled (PMINTENSET_EL1 == 0) */ -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);report (expect_interrupts (0 ),"no overflow interrupt after preset" );set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);isb (); -for (i =0 ; i <100 ; i++) +for (i =0 ; i <COUNT_INT ; i++)write_sysreg (0x2 , pmswinc_el0);isb ();@@ -1002,15 +1003,15 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_sysreg (ALL_SET_32 , pmintenset_el1);isb (); -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);set_pmcr (pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);isb (); -for (i =0 ; i <100 ; i++) +for (i =0 ; i <COUNT_INT ; i++)write_sysreg (0x3 , pmswinc_el0); -mem_access_loop (addr,200 , pmu.pmcr_ro); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro);report_info ("overflow=0x%lx" ,read_sysreg (pmovsclr_el0));report (expect_interrupts (0x3 ),"overflow interrupts expected on #0 and #1" );@@ -1029,7 +1030,7 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_regn_el0 (pmevtyper,1 ,CHAIN |PMEVTYPER_EXCLUDE_EL0 );write_regn_el0 (pmevcntr,0 , pre_overflow);isb (); -mem_access_loop (addr,200 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);report (expect_interrupts (0x1 ),"expect overflow interrupt" );/* overflow on odd counter */ @@ -1037,7 +1038,7 @@ static void test_overflow_interrupt(bool overflow_at_64bits)write_regn_el0 (pmevcntr,0 , pre_overflow);write_regn_el0 (pmevcntr,1 , all_set);isb (); -mem_access_loop (addr,400 , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp); +mem_access_loop (addr,COUNT_INT , pmu.pmcr_ro |PMU_PMCR_E | pmcr_lp);if (overflow_at_64bits) {report (expect_interrupts (0x1 ),"expect overflow interrupt on even counter" );Signature · 1 line
2.41.0
Quoted 3 lines · Eric Auger
On 11/7/23 15:05, Alexandru Elisei wrote:
...
Quoted 9 lines
Quoted 4 lines
By the way,
pmu_statsis not declared volatile, which means that the compiler is free to optimize accesses to the struct by caching previously read values in registers. Have you tried declaring it as volatile, in case that fixes the issues you were seeing?In my case it won't fix the issue because the stats match what happens but your suggestion makes total sense in general.
I will add that.
We also have READ/WRITE_ONCE() in lib/linux/compiler.h
Thanks,
drew