Skip to contentSkip to conversation

Revert "Bluetooth: btusb: mediatek: reset the controller before downloading the fw"

PATCH In review Geoffrey D. Bennett 2 participants 2 messages Mar 8, 2025

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 Revert "Bluetooth: btusb: mediatek: reset the controller before downloading the fw"

This reverts commit ccfc8948d7e4d93cab341a99774b24586717d89a.

The MediaTek Bluetooth controller reset that was added is causing Focusrite USB audio devices to fail to initialise when connected during boot on kernels 6.11 and newer.

The issue was reported by three users, with Scarlett 2nd Gen 6i6 and 3rd Gen Solo and 4i4 audio interfaces. Two of the reporters confirmed they have an MT7922.

The issue causes the interface to not work when connected at boot time, with errors like this observed in dmesg:

usb 3-4: parse_audio_format_rates_v2v3(): unable to find clock source (clock -110) usb 3-4: uac_clock_source_is_valid(): cannot get clock validity for id 41 usb 3-4: clock source 41 is not valid, cannot use

The problem only occurs when both devices and kernel modules are present and loaded during system boot, so it can be worked around by connecting the audio interface after booting.

Fixes ccfc8948d7e4 ("Bluetooth: btusb: mediatek: reset the controller before downloading the fw")
---
 drivers/bluetooth/btmtk.c | 10 ----------
 1 file changed, 10 deletions(-)
drivers/bluetooth/btmtk.c +0 -10
index 68846c5bd4f7..4390fd571dbd 100644
@@ -1330,13 +1330,6 @@ int btmtk_usb_setup(struct hci_dev *hdev)
 		break;
 	case 0x7922:
 	case 0x7925:
-		/* Reset the device to ensure it's in the initial state before
-		 * downloading the firmware to ensure.
-		 */
-
-		if (!test_bit(BTMTK_FIRMWARE_LOADED, &btmtk_data->flags))
-			btmtk_usb_subsys_reset(hdev, dev_id);
-		fallthrough;
 	case 0x7961:
 		btmtk_fw_get_filename(fw_bin_name, sizeof(fw_bin_name), dev_id,
 				      fw_version, fw_flavor);
@@ -1345,12 +1338,9 @@ int btmtk_usb_setup(struct hci_dev *hdev)
 						btmtk_usb_hci_wmt_sync);
 		if (err < 0) {
 			bt_dev_err(hdev, "Failed to set up firmware (%d)", err);
-			clear_bit(BTMTK_FIRMWARE_LOADED, &btmtk_data->flags);
 			return err;
 		}
 
-		set_bit(BTMTK_FIRMWARE_LOADED, &btmtk_data->flags);
-
 		/* It's Device EndPoint Reset Option Register */
 		err = btmtk_usb_uhw_reg_write(hdev, MTK_EP_RST_OPT,
 					      MTK_EP_RST_IN_OUT_OPT);

--
2.45.0

#1 lore raw

This is an automated email and please do not reply to this email.

Dear Submitter,

Thank you for submitting the patches to the linux bluetooth mailing list.
While preparing the CI tests, the patches you submitted couldn't be applied to the current HEAD of the repository.

----- Output -----

error: patch failed: drivers/bluetooth/btmtk.c:1328
error: drivers/bluetooth/btmtk.c: patch does not apply
hint: Use 'git am --show-current-patch' to see the failed patch

Please resolve the issue and submit the patches again.

---
Regards,
Linux Bluetooth