net: phy: aquantia: report Aquantia-specific settings and features
Subsystems (3)
Heiner Kallweit
maintainerv2 cover net: phy: aquantia: report Aquantia-specific settings and features
This series detects and reports quite some Aquantia-specific settings and features.
v2:
- propagate timeout in patch 2
Heiner Kallweit (3):
net: phy: aquantia: print remote capabilities if link partner is
Aquantia PHY
net: phy: aquantia: report PHY details like firmware version
net: phy: aquantia: inform about proprietary 1000Base-T2 mode being in
use
drivers/net/phy/aquantia_main.c | 123 ++++++++++++++++++++++++++++++++ 1 file changed, 123 insertions(+)
Signature · 1 line
2.21.0
Heiner Kallweit
maintainerPATCH v2 1/3 net: phy: aquantia: print remote capabilities if link partner is Aquantia PHY
If both link partners are Aquantia PHY's then additional information is exchanged as part of the auto-negotiation. Report remote capabilities if link partner is Aquantia PHY.
--- drivers/net/phy/aquantia_main.c | 49 +++++++++++++++++++++++++++++++++ 1 file changed, 49 insertions(+)
drivers/net/phy/aquantia_main.c +49 -0
@@ -58,6 +58,16 @@#define MDIO_AN_RX_LP_STAT1 0xe820#define MDIO_AN_RX_LP_STAT1_1000BASET_FULL BIT(15)#define MDIO_AN_RX_LP_STAT1_1000BASET_HALF BIT(14) +#define MDIO_AN_RX_LP_STAT1_SHORT_REACH BIT(13) +#define MDIO_AN_RX_LP_STAT1_AQRATE_DOWNSHIFT BIT(12) +#define MDIO_AN_RX_LP_STAT1_AQ_PHY BIT(2) + +#define MDIO_AN_RX_LP_STAT4 0xe823 +#define MDIO_AN_RX_LP_STAT4_FW_MAJOR GENMASK(15, 8) +#define MDIO_AN_RX_LP_STAT4_FW_MINOR GENMASK(7, 0) + +#define MDIO_AN_RX_VEND_STAT3 0xe832 +#define MDIO_AN_RX_VEND_STAT3_AFR BIT(0)/* Vendor specific 1, MDIO_MMD_VEND1 */ #define VEND1_GLOBAL_INT_STD_STATUS 0xfc00
@@ -376,6 +386,43 @@ static int aqcs109_config_init(struct phy_device *phydev)return aqr107_set_downshift (phydev,MDIO_AN_VEND_PROV_DOWNSHIFT_DFLT ); } +static void aqr107_link_change_notify (struct phy_device *phydev) +{ +u8 fw_major, fw_minor; +bool downshift, short_reach, afr; +int val; + +if (phydev->state !=PHY_RUNNING || phydev->autoneg ==AUTONEG_DISABLE ) +return ; + + val =phy_read_mmd (phydev,MDIO_MMD_AN ,MDIO_AN_RX_LP_STAT1 ); +/* call failed or link partner is no Aquantia PHY */ +if (val <0 || !(val &MDIO_AN_RX_LP_STAT1_AQ_PHY )) +return ; + + short_reach = val &MDIO_AN_RX_LP_STAT1_SHORT_REACH ; + downshift = val &MDIO_AN_RX_LP_STAT1_AQRATE_DOWNSHIFT ; + + val =phy_read_mmd (phydev,MDIO_MMD_AN ,MDIO_AN_RX_LP_STAT4 ); +if (val <0 ) +return ; + + fw_major =FIELD_GET (MDIO_AN_RX_LP_STAT4_FW_MAJOR , val); + fw_minor =FIELD_GET (MDIO_AN_RX_LP_STAT4_FW_MINOR , val); + + val =phy_read_mmd (phydev,MDIO_MMD_AN ,MDIO_AN_RX_VEND_STAT3 ); +if (val <0 ) +return ; + + afr = val &MDIO_AN_RX_VEND_STAT3_AFR ; + +phydev_dbg (phydev,"Link partner is Aquantia PHY, FW %u.%u%s%s%s\n" , + fw_major, fw_minor, + short_reach ?", short reach mode" :"" , + downshift ?", fast-retrain downshift advertised" :"" , + afr ?", fast reframe advertised" :"" ); +} +static struct phy_driver aqr_driver[] = { {PHY_ID_MATCH_MODEL (PHY_ID_AQ1202 ),
@@ -430,6 +477,7 @@ static struct phy_driver aqr_driver[] = { .read_status = aqr107_read_status, .get_tunable = aqr107_get_tunable, .set_tunable = aqr107_set_tunable, + .link_change_notify = aqr107_link_change_notify, }, { PHY_ID_MATCH_MODEL(PHY_ID_AQCS109),
@@ -444,6 +492,7 @@ static struct phy_driver aqr_driver[] = { .read_status = aqr107_read_status, .get_tunable = aqr107_get_tunable, .set_tunable = aqr107_set_tunable, + .link_change_notify = aqr107_link_change_notify, }, { PHY_ID_MATCH_MODEL(PHY_ID_AQR405),
Signature · 1 line
2.21.0
Heiner Kallweit
maintainerPATCH v2 2/3 net: phy: aquantia: report PHY details like firmware version
In reply to Heiner KallweitAdd reporting firmware details. These details are available only once the firmware has finished initializing the chip. This can take some time and we need to poll for init completion.
v2:
- Propagate timeout in aqr107_wait_reset_complete(). Don't bail out completely on timeout because chip may be functional even w/o firmware image.
--- drivers/net/phy/aquantia_main.c | 62 +++++++++++++++++++++++++++++++++ 1 file changed, 62 insertions(+)
drivers/net/phy/aquantia_main.c +62 -0
@@ -70,6 +70,14 @@#define MDIO_AN_RX_VEND_STAT3_AFR BIT(0)/* Vendor specific 1, MDIO_MMD_VEND1 */ +#define VEND1_GLOBAL_FW_ID 0x0020 +#define VEND1_GLOBAL_FW_ID_MAJOR GENMASK(15, 8) +#define VEND1_GLOBAL_FW_ID_MINOR GENMASK(7, 0) + +#define VEND1_GLOBAL_RSVD_STAT1 0xc885 +#define VEND1_GLOBAL_RSVD_STAT1_FW_BUILD_ID GENMASK(7, 4) +#define VEND1_GLOBAL_RSVD_STAT1_PROV_ID GENMASK(3, 0) +#define VEND1_GLOBAL_INT_STD_STATUS 0xfc00#define VEND1_GLOBAL_INT_VEND_STATUS 0xfc01
@@ -349,14 +357,64 @@ static int aqr107_set_tunable(struct phy_device *phydev, } } +/* If we configure settings whilst firmware is still initializing the chip, +* then these settings may be overwritten. Therefore make sure chip +* initialization has completed. Use presence of the firmware ID as +* indicator for initialization having completed. +* The chip also provides a "reset completed" bit, but it's cleared after +* read. Therefore function would time out if called again. +*/ +static int aqr107_wait_reset_complete (struct phy_device *phydev) +{ +int val, retries =100 ; + +do { + val =phy_read_mmd (phydev,MDIO_MMD_VEND1 ,VEND1_GLOBAL_FW_ID ); +if (val <0 ) +return val; +msleep (20 ); + }while (!val && --retries); + +return val ?0 : -ETIMEDOUT ; +} + +static void aqr107_chip_info (struct phy_device *phydev) +{ +u8 fw_major, fw_minor, build_id, prov_id; +int val; + + val =phy_read_mmd (phydev,MDIO_MMD_VEND1 ,VEND1_GLOBAL_FW_ID ); +if (val <0 ) +return ; + + fw_major =FIELD_GET (VEND1_GLOBAL_FW_ID_MAJOR , val); + fw_minor =FIELD_GET (VEND1_GLOBAL_FW_ID_MINOR , val); + + val =phy_read_mmd (phydev,MDIO_MMD_VEND1 ,VEND1_GLOBAL_RSVD_STAT1 ); +if (val <0 ) +return ; + + build_id =FIELD_GET (VEND1_GLOBAL_RSVD_STAT1_FW_BUILD_ID , val); + prov_id =FIELD_GET (VEND1_GLOBAL_RSVD_STAT1_PROV_ID , val); + +phydev_dbg (phydev,"FW %u.%u, Build %u, Provisioning %u\n" , + fw_major, fw_minor, build_id, prov_id); +} +static int aqr107_config_init (struct phy_device *phydev) { +int ret; +/* Check that the PHY interface type is compatible */ if (phydev->interface !=PHY_INTERFACE_MODE_SGMII && phydev->interface !=PHY_INTERFACE_MODE_2500BASEX && phydev->interface !=PHY_INTERFACE_MODE_10GKR )return -ENODEV ; + ret =aqr107_wait_reset_complete (phydev); +if (!ret) +aqr107_chip_info (phydev); +/* ensure that a latched downshift event is cleared */ aqr107_read_downshift_event (phydev);
@@ -372,6 +430,10 @@ static int aqcs109_config_init(struct phy_device *phydev) phydev->interface != PHY_INTERFACE_MODE_2500BASEX)return -ENODEV ; + ret =aqr107_wait_reset_complete (phydev); +if (!ret) +aqr107_chip_info (phydev); +/* AQCS109 belongs to a chip family partially supporting 10G and 5G. * PMA speed ability bits are the same for all members of the family, * AQCS109 however supports speeds up to 2.5G only.
Signature · 1 line
2.21.0
Heiner Kallweit
maintainerPATCH v2 3/3 net: phy: aquantia: inform about proprietary 1000Base-T2 mode being in use
In reply to Heiner KallweitThe AQCS109 supports a proprietary 2-pair 1Gbps mode. The standard registers don't allow to tell between 1000BaseT and 1000BaseT2. Add reporting this proprietary mode based on a vendor register.
--- drivers/net/phy/aquantia_main.c | 14 +++++++++++++- 1 file changed, 13 insertions(+), 1 deletion(-)
drivers/net/phy/aquantia_main.c +13 -1
@@ -78,6 +78,10 @@#define VEND1_GLOBAL_RSVD_STAT1_FW_BUILD_ID GENMASK(7, 4)#define VEND1_GLOBAL_RSVD_STAT1_PROV_ID GENMASK(3, 0) +#define VEND1_GLOBAL_RSVD_STAT9 0xc88d +#define VEND1_GLOBAL_RSVD_STAT9_MODE GENMASK(7, 0) +#define VEND1_GLOBAL_RSVD_STAT9_1000BT2 0x23 +#define VEND1_GLOBAL_INT_STD_STATUS 0xfc00#define VEND1_GLOBAL_INT_VEND_STATUS 0xfc01
@@ -448,7 +452,7 @@ static void aqr107_link_change_notify(struct phy_device *phydev) {u8 fw_major, fw_minor;bool downshift, short_reach, afr; -int val; +int mode, val;if (phydev->state !=PHY_RUNNING || phydev->autoneg ==AUTONEG_DISABLE )return ;
@@ -479,6 +483,14 @@ static void aqr107_link_change_notify(struct phy_device *phydev) short_reach ?", short reach mode" :"" , downshift ?", fast-retrain downshift advertised" :"" , afr ? ", fast reframe advertised" : ""); + + val =phy_read_mmd (phydev,MDIO_MMD_VEND1 ,VEND1_GLOBAL_RSVD_STAT9 ); +if (val <0 ) +return ; + + mode =FIELD_GET (VEND1_GLOBAL_RSVD_STAT9_MODE , val); +if (mode ==VEND1_GLOBAL_RSVD_STAT9_1000BT2 ) +phydev_info (phydev,"Aquantia 1000Base-T2 mode active\n" ); }static struct phy_driver aqr_driver[] = {
Signature · 1 line
2.21.0
David Miller
maintainerFrom: Heiner Kallweit <[email protected]>
Date: Sun, 24 Mar 2019 11:02:57 +0100
Quoted 5 lines
This series detects and reports quite some Aquantia-specific settings and features.
v2:
- propagate timeout in patch 2
Series applied, thanks Heiner.