Remove --no-replay
PATCH 1/1 Remove --no-replay
The --no-replay feature is considered to be a security weakness, which was also highlighed during the OpenVPN 2.4 security audit [0]. This option was added to the DeprecatedOptions[1] list and has been reported as deprecated since OpenVPN 2.4.
Now we remove it.
URL: [0] https://community.openvpn.net/openvpn/wiki/QuarkslabAndCryptographyEngineerAudits#OVPN-03-3:Insecureconfigurationoptions:--no-replay
URL: [1] https://community.openvpn.net/openvpn/wiki/DeprecatedOptions#Option:--no-replay
--- Changes.rst | 5 ++++ doc/man-sections/link-options.rst | 3 +-- doc/man-sections/server-options.rst | 2 +- src/openvpn/crypto.c | 21 ++-------------- src/openvpn/crypto.h | 5 +--- src/openvpn/init.c | 38 +++++++++-------------------- src/openvpn/options.c | 25 +------------------ src/openvpn/options.h | 1 - src/openvpn/ssl.c | 13 ++++------ src/openvpn/ssl_common.h | 1 - 10 files changed, 27 insertions(+), 87 deletions(-)
Changes.rst +5 -0
@@ -34,6 +34,11 @@ https://community.openvpn.net/openvpn/wiki/DeprecatedOptions With the improved and matured data channel cipher negotiation, the use of ``ncp-disable`` should not be necessary anymore. +- ``-no-replay`` has been removed + This has been listed as a deprecated option since OpenVPN 2.4 and + adds a security weakness. This was also highlighted during the + `OpenVPN 2.4 security audit <https://community.openvpn.net/openvpn/wiki/QuarkslabAndCryptographyEngineerAudits#OVPN-03-3:Insecureconfigurationoptions:--no-replay>`_. + Overview of changes in 2.4 ==========================
doc/man-sections/link-options.rst +1 -2
@@ -311,8 +311,7 @@ the local and the remote host. order they were received to the TCP/IP protocol stack, provided they satisfy several constraints. - (a) The packet cannot be a replay (unless ``--no-replay`` is - specified, which disables replay protection altogether). + (a) The packet cannot be a replay. (b) If a packet arrives out of order, it will only be accepted if the difference between its sequence number and the highest sequence
doc/man-sections/server-options.rst +1 -1
@@ -398,7 +398,7 @@ fast hardware. SSL/TLS authentication must be used in this mode. Options that will be compared for compatibility include ``dev-type``, ``link-mtu``, ``tun-mtu``, ``proto``, ``ifconfig``, ``comp-lzo``, ``fragment``, ``keydir``, ``cipher``, - ``auth``, ``keysize``, ``secret``, ``no-replay``, + ``auth``, ``keysize``, ``secret``, ``no-iv``, ``tls-auth``, ``key-method``, ``tls-server`` and ``tls-client``.
src/openvpn/crypto.c +2 -19
@@ -340,7 +340,7 @@ crypto_check_replay(struct crypto_options *opt,if (!(opt->flags &CO_MUTE_REPLAY_WARNINGS )) {msg (D_REPLAY_ERRORS ,"%s: bad packet ID (may be a replay): %s -- " -"see the man page entry for --no-replay and --replay-window for " +"see the man page entry for --replay-window for " "more info or silence this warning with --mute-replay-warnings" , error_prefix,packet_id_net_print (pin, true, gc)); }
@@ -697,15 +697,9 @@ openvpn_decrypt(struct buffer *buf, struct buffer work,void crypto_adjust_frame_parameters (struct frame *frame,const struct key_type *kt, -bool packet_id,bool packet_id_long_form) { -unsigned int crypto_overhead =0 ; - -if (packet_id) - { - crypto_overhead +=packet_id_size (packet_id_long_form); - } +unsigned int crypto_overhead =packet_id_size (packet_id_long_form);if (kt->cipher) {
@@ -1013,17 +1007,6 @@ fixup_key(struct key *key, const struct key_type *kt)gc_free (&gc); } -void -check_replay_consistency (const struct key_type *kt,bool packet_id) -{ -ASSERT (kt); - -if (!packet_id && (cipher_kt_mode_ofb_cfb (kt->cipher) - ||cipher_kt_mode_aead (kt->cipher))) - { -msg (M_FATAL ,"--no-replay cannot be used with a CFB, OFB or AEAD mode cipher" ); - } -}/* * Generate a random key. If key_type is provided, make
src/openvpn/crypto.h +1 -4
@@ -40,7 +40,7 @@* HMAC at all. * - \b Ciphertext \b IV. The IV size depends on the \c \-\-cipher option. * - \b Packet \b ID, a 32-bit incrementing packet counter that provides replay -* protection (if not disabled by \c \-\-no-replay). +* protection. * - \b Timestamp, a 32-bit timestamp of the current time. * - \b Payload, the plain text network packet to be encrypted (unless * encryption is disabled by using \c \-\-cipher \c none). The payload might
@@ -280,8 +280,6 @@ int write_key_file(const int nkeys, const char *filename);void generate_key_random (struct key *key,const struct key_type *kt); -void check_replay_consistency (const struct key_type *kt,bool packet_id); -bool check_key (struct key *key,const struct key_type *kt);void fixup_key (struct key *key,const struct key_type *kt);
@@ -414,7 +412,6 @@ bool crypto_check_replay(struct crypto_options *opt,/** Calculate crypto overhead and adjust frame to account for that */ void crypto_adjust_frame_parameters (struct frame *frame,const struct key_type *kt, -bool packet_id,bool packet_id_long_form);/** Return the worst-case OpenVPN crypto overhead (in bytes) */
src/openvpn/init.c +11 -27
@@ -2599,17 +2599,14 @@ do_init_crypto_static(struct context *c, const unsigned int flags) }/* Initialize packet ID tracking */ -if (options->replay) - { -packet_id_init (&c->c2.crypto_options.packet_id, - options->replay_window, - options->replay_time, -"STATIC" ,0 ); - c->c2.crypto_options.pid_persist = &c->c1.pid_persist; - c->c2.crypto_options.flags |=CO_PACKET_ID_LONG_FORM ; -packet_id_persist_load_obj (&c->c1.pid_persist, - &c->c2.crypto_options.packet_id); - } +packet_id_init (&c->c2.crypto_options.packet_id, + options->replay_window, + options->replay_time, +"STATIC" ,0 ); + c->c2.crypto_options.pid_persist = &c->c1.pid_persist; + c->c2.crypto_options.flags |=CO_PACKET_ID_LONG_FORM ; +packet_id_persist_load_obj (&c->c1.pid_persist, + &c->c2.crypto_options.packet_id);if (!key_ctx_bi_defined (&c->c1.ks.static_key)) {
@@ -2633,11 +2630,7 @@ do_init_crypto_static(struct context *c, const unsigned int flags) c->c2.crypto_options.key_ctx_bi = c->c1.ks.static_key;/* Compute MTU parameters */ -crypto_adjust_frame_parameters (&c->c2.frame, &c->c1.ks.key_type, - options->replay, true); - -/* Sanity check on sequence number, and cipher mode options */ -check_replay_consistency (&c->c1.ks.key_type, options->replay); +crypto_adjust_frame_parameters (&c->c2.frame, &c->c1.ks.key_type, true); }/*
@@ -2816,9 +2809,6 @@ do_init_crypto_tls(struct context *c, const unsigned int flags)return ; } -/* Sanity check on sequence number, and cipher mode options */ -check_replay_consistency (&c->c1.ks.key_type, options->replay); -/* In short form, unique datagram identifier is 32 bits, in long form 64 bits */ packet_id_long_form =cipher_kt_mode_ofb_cfb (c->c1.ks.key_type.cipher);
@@ -2831,7 +2821,7 @@ do_init_crypto_tls(struct context *c, const unsigned int flags)else {crypto_adjust_frame_parameters (&c->c2.frame, &c->c1.ks.key_type, - options->replay, packet_id_long_form); + packet_id_long_form); }tls_adjust_frame_parameters (&c->c2.frame);
@@ -2853,7 +2843,6 @@ do_init_crypto_tls(struct context *c, const unsigned int flags) to.key_type = c->c1.ks.key_type; to.server = options->tls_server; to.key_method = options->key_method; - to.replay = options->replay; to.replay_window = options->replay_window; to.replay_time = options->replay_time; to.tcp_mode =link_socket_proto_connection_oriented (options->ce.proto);
@@ -2987,7 +2976,7 @@ do_init_crypto_tls(struct context *c, const unsigned int flags) to.tls_wrap.opt.pid_persist = &c->c1.pid_persist; to.tls_wrap.opt.flags |=CO_PACKET_ID_LONG_FORM ;crypto_adjust_frame_parameters (&to.frame, &c->c1.ks.tls_auth_key_type, - true, true); + true); }/* TLS handshake encryption (--tls-crypt) */
@@ -3279,11 +3268,6 @@ do_option_warnings(struct context *c) }#endif /* if P2MP */ -if (!o->replay) - { -msg (M_WARN ,"WARNING: You have disabled Replay Protection (--no-replay) which may make " PACKAGE_NAME " less secure" ); - } -if (o->tls_server) {warn_on_use_of_common_subnets (&c->net_ctx);
src/openvpn/options.c +1 -24
@@ -555,7 +555,6 @@ static const char usage_message[] =#ifndef ENABLE_CRYPTO_MBEDTLS "--engine [name] : Enable OpenSSL hardware crypto engine functionality.\n"#endif -"--no-replay : (DEPRECATED) Disable replay protection.\n" "--mute-replay-warnings : Silence the output of replay warnings to log file.\n" "--replay-window n [t] : Use a replay protection sliding window of size n\n" " and a time window of t seconds.\n"
@@ -880,7 +879,6 @@ init_options(struct options *o, const bool init_gc) o->authname ="SHA1" ; o->prng_hash ="SHA1" ; o->prng_nonce_secret_len =16 ; - o->replay = true; o->replay_window =DEFAULT_SEQ_BACKTRACK ; o->replay_time =DEFAULT_TIME_BACKTRACK ; o->key_direction =KEY_DIRECTION_BIDIRECTIONAL ;
@@ -1709,7 +1707,6 @@ show_settings(const struct options *o)#ifndef ENABLE_CRYPTO_MBEDTLS SHOW_BOOL (engine);#endif /* ENABLE_CRYPTO_MBEDTLS */ -SHOW_BOOL (replay);SHOW_BOOL (mute_replay_warnings);SHOW_INT (replay_window);SHOW_INT (replay_time);
@@ -2526,16 +2523,6 @@ options_postprocess_verify_ce(const struct options *options, const struct connecmsg (M_WARN ,"WARNING: --keysize is DEPRECATED and will be removed in OpenVPN 2.6" ); } -/* -* Check consistency of replay options -*/ -if (!options->replay - && (options->replay_window != defaults.replay_window - || options->replay_time != defaults.replay_time)) - { -msg (M_USAGE ,"--replay-window doesn't make sense when replay protection is disabled with --no-replay" ); - } -/* * SSL/TLS mode sanity checks. */
@@ -3629,7 +3616,7 @@ calc_options_string_link_mtu(const struct options *o, const struct frame *frame)init_key_type (&fake_kt, o->ciphername, o->authname, o->keysize, true, false);frame_remove_from_extra_frame (&fake_frame,crypto_max_overhead ()); -crypto_adjust_frame_parameters (&fake_frame, &fake_kt, o->replay, +crypto_adjust_frame_parameters (&fake_frame, &fake_kt,cipher_kt_mode_ofb_cfb (fake_kt.cipher));frame_finalize (&fake_frame, o->ce.link_mtu_defined, o->ce.link_mtu, o->ce.tun_mtu_defined, o->ce.tun_mtu);
@@ -3673,7 +3660,6 @@ calc_options_string_link_mtu(const struct options *o, const struct frame *frame)* --auth * --keysize * --secret -* --no-replay * * SSL Options: *
@@ -3802,10 +3788,6 @@ options_string(const struct options *o, {buf_printf (&out,",secret" ); } -if (!o->replay) - { -buf_printf (&out,",no-replay" ); - }#ifdef ENABLE_PREDICTION_RESISTANCE if (o->use_prediction_resistance)
@@ -7958,11 +7940,6 @@ add_option(struct options *options, } } } -else if (streq (p[0 ],"no-replay" ) && !p[1 ]) - { -VERIFY_PERMISSION (OPT_P_GENERAL ); - options->replay = false; - }else if (streq (p[0 ],"replay-window" ) && !p[3 ]) {VERIFY_PERMISSION (OPT_P_GENERAL );
src/openvpn/options.h +0 -1
@@ -514,7 +514,6 @@ struct optionsconst char *prng_hash;int prng_nonce_secret_len;const char *engine; -bool replay;bool mute_replay_warnings;int replay_window;int replay_time;
src/openvpn/ssl.c +5 -8
@@ -952,12 +952,9 @@ key_state_init(struct tls_session *session, struct key_state *ks)reliable_set_timeout (ks->send_reliable, session->opt->packet_timeout);/* init packet ID tracker */ -if (session->opt->replay) - { -packet_id_init (&ks->crypto_options.packet_id, - session->opt->replay_window, session->opt->replay_time,"SSL" , - ks->key_id); - } +packet_id_init (&ks->crypto_options.packet_id, + session->opt->replay_window, session->opt->replay_time,"SSL" , + ks->key_id); ks->crypto_options.pid_persist =NULL ;
@@ -2006,7 +2003,7 @@ tls_session_update_crypto_params(struct tls_session *session,/* Update frame parameters: undo worst-case overhead, add actual overhead */ frame_remove_from_extra_frame (frame,crypto_max_overhead ());crypto_adjust_frame_parameters (frame, &session->opt->key_type, - options->replay, packet_id_long_form); + packet_id_long_form);frame_finalize (frame, options->ce.link_mtu_defined, options->ce.link_mtu, options->ce.tun_mtu_defined, options->ce.tun_mtu);frame_init_mssfix (frame, options);
@@ -2023,7 +2020,7 @@ tls_session_update_crypto_params(struct tls_session *session, {frame_remove_from_extra_frame (frame_fragment,crypto_max_overhead ());crypto_adjust_frame_parameters (frame_fragment, &session->opt->key_type, - options->replay, packet_id_long_form); + packet_id_long_form);frame_set_mtu_dynamic (frame_fragment, options->ce.fragment,SET_MTU_UPPER_BOUND );frame_print (frame_fragment,D_MTU_INFO ,"Fragmentation MTU parms" ); }
src/openvpn/ssl_common.h +0 -1
@@ -263,7 +263,6 @@ struct tls_options/* from command line */ int key_method; -bool replay;bool single_session;#ifdef ENABLE_OCC bool disable_occ;
Signature · 1 line
2.26.0
Am 17.07.20 um 19:10 schrieb David Sommerseth:
Quoted 4 lines
The --no-replay feature is considered to be a security weakness, which was also highlighed during the OpenVPN 2.4 security audit [0]. This option was added to the DeprecatedOptions[1] list and has been reported as deprecated since OpenVPN 2.4.
As a side note, removing this feature weakens the ability to use OpenVPN is a pure tunnel without crypto (--auth none, --cipher none and no-replay) since this removes the ability to disable replay proctection when no authentication is enabled. (replay protection without auth is silly as a attacker can just fake the replay id too.)
Am 26.07.20 um 02:01 schrieb Arne Schwabe:
Quoted 6 lines
Am 17.07.20 um 19:10 schrieb David Sommerseth:
Quoted 4 lines
The --no-replay feature is considered to be a security weakness, which was also highlighed during the OpenVPN 2.4 security audit [0]. This option was added to the DeprecatedOptions[1] list and has been reported as deprecated since OpenVPN 2.4.
Quoted 7 lines
As a side note, removing this feature weakens the ability to use OpenVPN is a pure tunnel without crypto (--auth none, --cipher none and no-replay) since this removes the ability to disable replay proctection when no authentication is enabled. (replay protection without auth is silly as a attacker can just fake the replay id too.)
Acked-by Arne Schwabe
I given that a bit of a thought. But we need to decide if we to support unencrypted transport only session or not in future. If we do not want to support them, then applying this patch is fine, otherwise we should restrict disabling no-replay to --auth none and also --auth none to --cipher none basically:
--cipher != none => auth none and no-replay forbidden
--cipher == none => allows auth none and also no-replay
--cipher none and auth none, warn if no-replay is used that it does not prevent replay attacks. But do not fail since we would break a lot of setups.
Hi,
Quoted 21 lines · Arne Schwabe
Am 26.07.20 um 02:01 schrieb Arne Schwabe:
Quoted 6 lines
Am 17.07.20 um 19:10 schrieb David Sommerseth:
Quoted 4 lines
The --no-replay feature is considered to be a security weakness, which was also highlighed during the OpenVPN 2.4 security audit [0]. This option was added to the DeprecatedOptions[1] list and has been reported as deprecated since OpenVPN 2.4.
Quoted 7 lines
As a side note, removing this feature weakens the ability to use OpenVPN is a pure tunnel without crypto (--auth none, --cipher none and no-replay) since this removes the ability to disable replay proctection when no authentication is enabled. (replay protection without auth is silly as a attacker can just fake the replay id too.)
Acked-by Arne SchwabeI given that a bit of a thought. But we need to decide if we to support unencrypted transport only session or not in future. If we do not want to support them, then applying this patch is fine, otherwise we should restrict disabling no-replay to --auth none and also --auth none to --cipher none basically:
Quoted 7 lines
--cipher != none => auth none and no-replay forbidden
--cipher == none => allows auth none and also no-replay
--cipher none and auth none, warn if no-replay is used that it does not prevent replay attacks. But do not fail since we would break a lot of setups.
I work for the ministry of oversimplification and I think that removing user knobs is simply a good thing.
Following the logic provided by Arne, how about removing the --no-reply knob and making this mechanism automatic?
* if cipher != none -> replay prevention is always enabled;
* if cipher == none && auth == none -> replay prevention is disabled.
[allowing or disabling auth=none should be tackled saparately imho]
Regards,
Signature · 1 line
Antonio Quartulli
Hi,
Quoted 33 lines · Antonio Quartulli
Quoted 21 lines · Arne Schwabe
Am 26.07.20 um 02:01 schrieb Arne Schwabe:
Quoted 6 lines
Am 17.07.20 um 19:10 schrieb David Sommerseth:
Quoted 4 lines
The --no-replay feature is considered to be a security weakness, which was also highlighed during the OpenVPN 2.4 security audit [0]. This option was added to the DeprecatedOptions[1] list and has been reported as deprecated since OpenVPN 2.4.
Quoted 7 lines
As a side note, removing this feature weakens the ability to use OpenVPN is a pure tunnel without crypto (--auth none, --cipher none and no-replay) since this removes the ability to disable replay proctection when no authentication is enabled. (replay protection without auth is silly as a attacker can just fake the replay id too.)
Acked-by Arne SchwabeI given that a bit of a thought. But we need to decide if we to support unencrypted transport only session or not in future. If we do not want to support them, then applying this patch is fine, otherwise we should restrict disabling no-replay to --auth none and also --auth none to --cipher none basically:
Quoted 7 lines
--cipher != none => auth none and no-replay forbidden
--cipher == none => allows auth none and also no-replay
--cipher none and auth none, warn if no-replay is used that it does not prevent replay attacks. But do not fail since we would break a lot of setups.
I work for the ministry of oversimplification and I think that removing user knobs is simply a good thing.
Quoted 8 lines
Following the logic provided by Arne, how about removing the --no-reply knob and making this mechanism automatic?
* if cipher != none -> replay prevention is always enabled;
* if cipher == none && auth == none -> replay prevention is disabled.[allowing or disabling auth=none should be tackled saparately imho]
Before getting into solutions, let me state a few facts:
1. Replay protection only really works when authentication is enabled.
2. Our AEAD modes all require replay protection.
3. Automatically disabling replay protection will cause a config backward compatibility break.
Given 1, if we were to couple allowing --no-replay to some crypto settings, I would say it should be coupled to --auth none.
Given 2, how clear is our timeline on sunsetting non-AEAD ciphers? That would automatically sunset --no-replay. (I've lost track a bit...)
Point 3 should not really be a problem, because --no-replay has been deprecated since 2.4 (2017), and is an edge use-case anyway. But it should be a conscious decision.
So, unless we're about to sunset non-AEAD ciphers soon (which would automatically solve the issue), I would suggest a small variation to Antonio's approach:
Remove the option, and:
* if auth != none -> replay prevention is always enabled;
* if auth == none -> replay prevention is disabled.
(Of course, considering that auth != none for AEAD cipher modes, even when --auth none is set.)
-Steffan
Quoted 4 lines
Given 2, how clear is our timeline on sunsetting non-AEAD ciphers? That would automatically sunset --no-replay. (I've lost track a bit...)
Heated debate as that is equal to drop compatibility completely with OpenVPN 2.3. We have already a heated debate if dropping 2.3 config compatibility is possible or not (e.g. you need to add ciphers to data-ciphers to still to connect to a 2.3 peer).
Arne
On 16/05/2021 19:14, Arne Schwabe wrote:
First of all, I do like Steffan's proposal:
Quoted 3 lines
Remove the option, and:
* if auth != none -> replay prevention is always enabled;
* if auth == none -> replay prevention is disabled.
And with "remove the option", if it exists in a config, it should be considered a NOOP.
Then on compatibility ...
Quoted 7 lines
Quoted 2 lines
Given 2, how clear is our timeline on sunsetting non-AEAD ciphers? That would automatically sunset --no-replay. (I've lost track a bit...)
Heated debate as that is equal to drop compatibility completely with OpenVPN 2.3. We have already a heated debate if dropping 2.3 config compatibility is possible or not (e.g. you need to add ciphers to data-ciphers to still to connect to a 2.3 peer).
Just to be clear, since I have been involved in several of these discussions. I consider 2.3 dead. I care about 2.4 and upwards, based on the agreement we had long time ago about which versions we want to support [0]. 2.3 is now in git-only support and we have only promised that support level until end of June (essentially ~6 more weeks).
[0] <https://community.openvpn.net/openvpn/wiki/SupportedVersions>
For me, I care only about 2.4 and newer at this point. If someone desperately need to support 2.3 clients, it is not our task to provide such support. If someone need a 2.6 client to connect to a 2.3 server, that is also not our task to provide. If 2.3 is so badly needed, you cannot expect to blend in 2.6 without issues.
We cannot be held hostage due to our users incapability to upgrade, even when related to hardware. Our current support time is quite reasonable, where we go from full -> old stable -> git-only -> unsupported which takes about 2.5 year. If a site cares about their VPN setup, that is more than long enough time to plan and deploy an upgrade. *And* it is the distributor itself who must carry the main support burden if they decide to support versions not supported by the upstream project. So for LTS distributions, it is the LTS distribution providing the packages which defines when their LTS distribution goes EOL - and they support the packages they provide in that LTS distribution.
That said, we can strive to support older versions, but we should not spend lots of time and energy supporting it just for the sake of supporting it.
What I do care about is that _client_ configuration files targetted for _2.4_ clients can connect to 2.4 and newer servers without modifying the configuration files. But I am at the same time willing to accept that DCO will change that game. Also, if a site has deployed a server configuration for 2.5 or 2.6 explicitly and have accordingly scoped their client configuration for the same version, supporting older clients should _not_ be expected to work. But for existing 2.4 servers, we should not break configurations on 2.4 or newer clients. So basically, 2.4/2.5/2.6 should be able to work out-of-the-box without any changes, regardless of versions.
However, if connecting to a *DCO enabled host*, updating client configurations *is* acceptable *because* that is a completely new technology which is not targetting everything 2.4 supports by design *and* _not_ making use of DCO will still work.
For sites wanting to support both DCO and non-DCO, we could consider looking into ensuring that connection-blocks can be used where the server side will have an openvpn server running with DCO and another one without DCO. This means adding DCO on an already existing server could be done using a different port or IP address (--local). Unless we want ovpn-dco to be able to be a simple and passive forwarder of both control and data channel packets if the configuration is not DCO compliant.
The challenge is that cipher/auth settings cannot be in a connection block, which means the current behaviour in 2.4 need to be preserved, unless we can push settings (NCP and related). It is also acceptable to me that clients may ignore local cipher/auth settings which can be pushed from the server.
But I also do know NCP is a bit tricky with the current DCO implementation, where this needs to be settled on a DCO supported cipher before connecting. Maybe we should consider a similar approach to OpenVPN 3, where the tun/DCO interface is setup *after* the connection to the server has been established with the PUSH_REPLY received and pass UDP/TCP socket to ovpn-dco at that point *if* the server side cipher/auth/compression is compliant with DCO? (Otherwise, use a tun interface)
Signature · 4 lines
kind regards, David Sommerseth OpenVPN Inc
Am 17.05.21 um 01:58 schrieb David Sommerseth:
Quoted 10 lines · Arne Schwabe
First of all, I do like Steffan's proposal:
Quoted 3 lines
Remove the option, and:
* if auth != none -> replay prevention is always enabled;
* if auth == none -> replay prevention is disabled.And with "remove the option", if it exists in a config, it should be considered a NOOP.
If I am not mistaken no-replay changes the wire-format so we cannot ignore it when present. I vaguely remember that the packet id does not get added to cbc mode packets if no-replay is active.
Quoted 16 lines
Then on compatibility ...
Quoted 7 lines
Quoted 2 lines
Given 2, how clear is our timeline on sunsetting non-AEAD ciphers? That would automatically sunset --no-replay. (I've lost track a bit...)
Heated debate as that is equal to drop compatibility completely with OpenVPN 2.3. We have already a heated debate if dropping 2.3 config compatibility is possible or not (e.g. you need to add ciphers to data-ciphers to still to connect to a 2.3 peer).
Just to be clear, since I have been involved in several of these discussions. I consider 2.3 dead. I care about 2.4 and upwards, based on the agreement we had long time ago about which versions we want to support [0]. 2.3 is now in git-only support and we have only promised that support level until end of June (essentially ~6 more weeks).
Quoted 7 lines
[0] <https://community.openvpn.net/openvpn/wiki/SupportedVersions>
For me, I care only about 2.4 and newer at this point. If someone desperately need to support 2.3 clients, it is not our task to provide such support. If someone need a 2.6 client to connect to a 2.3 server, that is also not our task to provide. If 2.3 is so badly needed, you cannot expect to blend in 2.6 without issues.
That is always easy to say if you don't have to deal with the users.
Quoted 11 lines
What I do care about is that _client_ configuration files targetted for _2.4_ clients can connect to 2.4 and newer servers without modifying the configuration files. But I am at the same time willing to accept that DCO will change that game. Also, if a site has deployed a server configuration for 2.5 or 2.6 explicitly and have accordingly scoped their client configuration for the same version, supporting older clients should _not_ be expected to work. But for existing 2.4 servers, we should not break configurations on 2.4 or newer clients. So basically, 2.4/2.5/2.6 should be able to work out-of-the-box without any changes, regardless of versions.
Quoted 4 lines
However, if connecting to a *DCO enabled host*, updating client configurations *is* acceptable *because* that is a completely new technology which is not targetting everything 2.4 supports by design *and* _not_ making use of DCO will still work.
I think people that upgrade their clients should also able to benefit from DCO. And in most setups distributing new configuration files is not so easy. So if extra steps are needed to enable DCO, most people will simply not use DCO or worse, end up with a setup that doesn't work anymore if they switch to ovpn-dco-win.
Quoted 8 lines
For sites wanting to support both DCO and non-DCO, we could consider looking into ensuring that connection-blocks can be used where the server side will have an openvpn server running with DCO and another one without DCO. This means adding DCO on an already existing server could be done using a different port or IP address (--local). Unless we want ovpn-dco to be able to be a simple and passive forwarder of both control and data channel packets if the configuration is not DCO compliant.
This whole discussion is mute if you don't want support 2.3 anyway as the problem does not exist if you want to support 2.4+ only.
Quoted 9 lines
But I also do know NCP is a bit tricky with the current DCO implementation, where this needs to be settled on a DCO supported cipher before connecting. Maybe we should consider a similar approach to OpenVPN 3, where the tun/DCO interface is setup *after* the connection to the server has been established with the
PUSH_REPLYreceived and pass UDP/TCP socket to ovpn-dco at that point *if* the server side cipher/auth/compression is compliant with DCO? (Otherwise, use a tun interface)
OpenVPN 2.x can also work without pull. Most importantly the server needs to open the interface before any connection. And I think also OpenVPN3 breaks apart when you put persist-tun into the mix. Furthermore under Windows with ovpn-dco-win this approach does not work at all anyway.
Arne