FPGA Manager - Partial Reconfiguration support for Xilinx Zynq-7000
Hi,
I asked the question on Xilinx forums about 1 months ago but didn't get any response [1]. I hope that someone on this list may guide me.
I am creating Linux based images for Zynq-7000 devices by using Petalinux 2018.3 which is a set of build tools provided by Xilinx. For FPGA management, FPGA Manager is included by default. However it doesn't support partial reconfiguration for Zynq-7000 devices as stated [2]. I tested and verified that it doesn't work. I assumed that /drivers/fpga/zynq-fpga.c is the source code, checked it and noticed some comments about partial reconfig. AFAIK previous driver used by Xilinx before FPGA Manager whose source code file is xilinx_devcfg.c supported partial reconfig. So I don't think that there is a hardware limitation since the previous solution was working on the same device. So I wonder why the newest method is less capable than the older one. I need partial reconfig support for the newest petalinux version. What should I do?
a) Compile old xilinx_devcfg.c driver for Petalinux 2018.3 and disable FPGA Manager.
b) Somehow patch FPGA Manager
c) Wait (how long?) Xilinx to solve this issue
Two names are listed as MODULE_AUTHOR of zynq-fpga.c: Moritz Fischer and Michal Simek. I don't know whether they are subscribed to this list or not.
[1]: https://forums.xilinx.com/t5/Embedded-Linux/Partial-Reconfiguration-support-in-Petalinux-2018-3-for-Zynq/td-p/934057
[2]: https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18841645/Solution+Zynq+PL+Programming+With+FPGA+Manager
Best,
Alper
Hi,
Quoted 10 lines · Alper Yazar
Hi,
I asked the question on Xilinx forums about 1 months ago but didn't get any response [1]. I hope that someone on this list may guide me.
I am creating Linux based images for Zynq-7000 devices by using Petalinux 2018.3 which is a set of build tools provided by Xilinx. For FPGA management, FPGA Manager is included by default. However it doesn't support partial reconfiguration for Zynq-7000 devices as stated [2]. I tested and verified that it doesn't work. I assumed that /drivers/fpga/zynq-fpga.c is the source code, checked it and noticed some comments about partial reconfig. AFAIK previous driver used by Xilinx before FPGA Manager whose source code file is
xilinx_devcfg.csupported partial reconfig. So I don't think that there is a hardware limitation since the previous solution was working on the same device. So I wonder why the newest method is less capable than the older one. I need partial reconfig support for the newest petalinux version. What should I do?a) Compile old
xilinx_devcfg.cdriver for Petalinux 2018.3 and disable FPGA Manager.b) Somehow patch FPGA Manager
Quoted 7 lines
c) Wait (how long?) Xilinx to solve this issue
Two names are listed as
MODULE_AUTHORofzynq-fpga.c: Moritz Fischer and Michal Simek. I don't know whether they are subscribed to this list or not.[1]: https://forums.xilinx.com/t5/Embedded-Linux/Partial-Reconfiguration-support-in-Petalinux-2018-3-for-Zynq/td-p/934057
[2]: https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18841645/Solution+Zynq+PL+Programming+With+FPGA+Manager
Nava: Can you please check if partial reconfiguration is still working? I see code in the driver.
Alper: Can you please use u-boot and check that your bitstreams are correct?
Also will be good to have some logs to see what it is happening.
Thanks,
Michal
Quoted 24 lines · Michal Simek
Hi,
Quoted 10 lines · Alper Yazar
Hi,
I asked the question on Xilinx forums about 1 months ago but didn't get any response [1]. I hope that someone on this list may guide me.
I am creating Linux based images for Zynq-7000 devices by using Petalinux 2018.3 which is a set of build tools provided by Xilinx. For FPGA management, FPGA Manager is included by default. However it doesn't support partial reconfiguration for Zynq-7000 devices as stated [2]. I tested and verified that it doesn't work. I assumed that /drivers/fpga/zynq-fpga.c is the source code, checked it and noticed some comments about partial reconfig. AFAIK previous driver used by Xilinx before FPGA Manager whose source code file is
xilinx_devcfg.csupported partial reconfig. So I don't think that there is a hardware limitation since the previous solution was working on the same device. So I wonder why the newest method is less capable than the older one. I need partial reconfig support for the newest petalinux version. What should I do?a) Compile old
xilinx_devcfg.cdriver for Petalinux 2018.3 and disable FPGA Manager.b) Somehow patch FPGA Manager
Quoted 7 lines
c) Wait (how long?) Xilinx to solve this issue
Two names are listed as
MODULE_AUTHORofzynq-fpga.c: Moritz Fischer and Michal Simek. I don't know whether they are subscribed to this list or not.[1]: https://forums.xilinx.com/t5/Embedded-Linux/Partial-Reconfiguration-support-in-Petalinux-2018-3-for-Zynq/td-p/934057
[2]: https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18841645/Solution+Zynq+PL+Programming+With+FPGA+ManagerNava: Can you please check if partial reconfiguration is still working? I see code in the driver.
Quoted 7 lines
Alper: Can you please use u-boot and check that your bitstreams are correct?
Also will be good to have some logs to see what it is happening.Thanks,
Michal
Hi Michal,
Sorry for late response. We checked U-boot and it worked without any problem. Our bitstreams are based on the Xilinx example project on partial reconfiguration.
1. Loading full bitstream using U-boot (successful):
Zynq> fatload mmc 0 0x4000000 top.bit
reading top.bit
4045663 bytes read in 235 ms (16.4 MiB/s)
Zynq> fpga loadb 0 0x4000000 4045663
design filename = "top;UserID=0XFFFFFFFF;Version=2018.3"
part number = "7z020clg484"
date = "2019/01/30"
time = "00:54:18"
bytes in bitstream = 4045564
zynq_align_dma_buffer: Align buffer at 4000063 to 3ffff80(swap 1)
2. Loading partial bitstream using U-boot (successful):
Zynq> fatload mmc 0 0x4000000 S_knight_top_partial.bit
reading S_knight_top_partial.bit
1238420 bytes read in 81 ms (14.6 MiB/s)
Zynq> fpga loadbp 0 0x4000000 1238420
design filename = "top;UserID=0XFFFFFFFF;PARTIAL=TRUE;Version=2018.3"
part number = "7z020clg484"
date = "2019/01/30"
time = "00:54:40"
bytes in bitstream = 1238308
zynq_align_dma_buffer: Align buffer at 4000070 to 3ffff80(swap 1)
Both of them worked fine.
3. Loading full bitstream on Petalinux 2018.3 (successful):
root@project4:~# mkdir -p /lib/firmware
root@project4:~# cd /mnt
root@project4:/mnt# cp top.bit.bin /lib/firmware
root@project4:/mnt# echo top.bit.bin >/sys/class/fpga_manager/fpga0/firmware
fpga_manager fpga0: writing top.bit.bin to Xilinx Zynq FPGA Manager
4. Loading partial bitstream on Petalinux 2018.3 (NOT successful):
root@project4:/mnt# cp S_knight_top_partial.bit.bin /lib/firmware
root@project4:/mnt# echo S_knight_top_partial.bit.bin >/sys/class/fpga_manager/fpga0/firmware
fpga_manager fpga0: writing S_knight_top_partial.bit.bin to Xilinx Zynq FPGA Manager
--- Wait few seconds ---
fpga_manager fpga0: Error after writing image data to FPGA
-sh: echo: write error: Connection timed out
We also checked fpga-mgr.h and saw the definiton: "#define FPGA_MGR_PARTIAL_RECONFIG BIT(0)". For partial bitstream trials we also tried setting this bit to 1 by "echo 1 > /sys/class/fpga_manager/fpga0/flags" command but this didn't affect the result.
Since FPGA manager uses BIN file we convert BIT to BIN using SDK. U-boot works with BIT files. Is it possible that this conversion cause the problem? How should we convert BIT to BIN file?
Best,
Alper
Hi Alper Yazar,
Please look at the below wiki link to generate .bin form .bit file.
https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18841645/Solution+Zynq+PL+Programming+With+FPGA+Manager#SolutionZynqPLProgrammingWithFPGAManager-Generating.binfrom.bitfileusingBootgen
Regards,
Navakishore.
Quoted 156 lines
-----Original Message-----
From: Alper Yazar [mailto:[email protected]]
Sent: Sunday, May 5, 2019 2:11 PM
To: Michal Simek <[email protected]>; [email protected]; Nava kishore Manne <[email protected]>
Cc: Ronan Keryell <[email protected]>
Subject: Re: FPGA Manager - Partial Reconfiguration support for Xilinx Zynq- 7000Quoted 6 lines · Michal Simek
Hi,
Quoted 3 lines · Alper Yazar
Hi,
I asked the question on Xilinx forums about 1 months ago but didn't get any
response [1]. I hope that someone on this list may guide me.
Quoted 2 lines
Quoted 2 lines
I am creating Linux based images for Zynq-7000 devices by using Petalinux
2018.3 which is a set of build tools provided by Xilinx. For FPGA management, FPGA Manager is included by default. However it doesn't support partial reconfiguration for Zynq-7000 devices as stated [2]. I tested and verified that it doesn't work. I assumed that /drivers/fpga/zynq-fpga.c is the source code, checked it and noticed some comments about partial reconfig. AFAIK previous driver used by Xilinx before FPGA Manager whose source code file is
xilinx_devcfg.csupported partial reconfig. So I don't think that there is a hardware limitation since the previous solution was working on the same device. So I wonder why the newest method is less capable than the older one. I need partial reconfig support for the newest petalinux version. What should I do?Quoted 2 lines
Quoted 2 lines
a) Compile old
xilinx_devcfg.cdriver for Petalinux 2018.3 and disable FPGAManager.
Quoted 6 lines
Quoted 6 lines
b) Somehow patch FPGA Manager
c) Wait (how long?) Xilinx to solve this issue
Two names are listed as
MODULE_AUTHORofzynq-fpga.c: Moritz Fischerand Michal Simek. I don't know whether they are subscribed to this list or not.
Quoted 12 lines
Quoted 8 lines
[1]:
https://forums.xilinx.com/t5/Embedded-Linux/Partial-Reconfiguration-s
upport-in-Petalinux-2018-3-for-Zynq/td-p/934057
[2]:
https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18841645/Soluti
on+Zynq+PL+Programming+With+FPGA+ManagerNava: Can you please check if partial reconfiguration is still working? I see code in the driver.
Quoted 7 lines
Alper: Can you please use u-boot and check that your bitstreams are correct?
Also will be good to have some logs to see what it is happening.Thanks,
MichalHi Michal,
Sorry for late response. We checked U-boot and it worked without any problem. Our bitstreams are based on the Xilinx example project on partial reconfiguration.
1. Loading full bitstream using U-boot (successful):
Zynq> fatload mmc 0
0x4000000top.bitreading top.bit
4045663 bytes read in 235 ms (16.4 MiB/s)
Zynq> fpga loadb 0
0x40000004045663design filename = "top;UserID=0XFFFFFFFF;Version=2018.3"
part number = "7z020clg484"
date = "2019/01/30"
time = "00:54:18"
bytes in bitstream = 4045564
zynq_align_dma_buffer: Align buffer at 4000063 to 3ffff80(swap 1)2. Loading partial bitstream using U-boot (successful):
Zynq> fatload mmc 0
0x4000000S_knight_top_partial.bitreading S_knight_top_partial.bit
1238420 bytes read in 81 ms (14.6 MiB/s)
Zynq> fpga loadbp 0
0x40000001238420design filename = "top;UserID=0XFFFFFFFF;PARTIAL=TRUE;Version=2018.3"
part number = "7z020clg484"
date = "2019/01/30"
time = "00:54:40"
bytes in bitstream = 1238308
zynq_align_dma_buffer: Align buffer at 4000070 to 3ffff80(swap 1)Both of them worked fine.
3. Loading full bitstream on Petalinux 2018.3 (successful):
root@project4:~# mkdir -p /lib/firmwareroot@project4:~# cd /mntroot@project4:/mnt# cp top.bit.bin /lib/firmwareroot@project4:/mnt# echo top.bit.binQuoted 1 line
/sys/class/fpga_manager/fpga0/firmware
fpga_managerfpga0: writing top.bit.bin to Xilinx Zynq FPGA Manager4. Loading partial bitstream on Petalinux 2018.3 (NOT successful):
root@project4:/mnt# cp S_knight_top_partial.bit.bin /lib/firmwareroot@project4:/mnt# echo S_knight_top_partial.bit.binQuoted 1 line
/sys/class/fpga_manager/fpga0/firmware
fpga_managerfpga0: writing S_knight_top_partial.bit.bin to Xilinx Zynq FPGA Manager--- Wait few seconds ---
fpga_managerfpga0: Error after writing image data to FPGA-sh: echo: write error: Connection timed out
We also checked
fpga-mgr.hand saw the definiton: "#defineFPGA_MGR_PARTIAL_RECONFIGBIT(0)". For partial bitstream trials we
also tried setting this bit to 1 by "echo 1 >/sys/class/fpga_manager/fpga0/flags" command but this didn't affect the result.Since FPGA manager uses BIN file we convert BIT to BIN using SDK. U-boot works with BIT files. Is it possible that this conversion cause the problem? How should we convert BIT to BIN file?
Best,
Alper
Hi again,
It looks like partial reconfiguration for Zynq-7000 working since Petalinux 2019.1.
Best,
Alper
Quoted 156 lines
Hi Alper Yazar,
Please look at the below wiki link to generate .bin form .bit file.
https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18841645/Solution+Zynq+PL+Programming+With+FPGA+Manager#SolutionZynqPLProgrammingWithFPGAManager-Generating.binfrom.bitfileusingBootgenRegards,
Navakishore.Quoted 148 lines
-----Original Message-----
From: Alper Yazar [mailto:[email protected]]
Sent: Sunday, May 5, 2019 2:11 PM
To: Michal Simek <[email protected]>; [email protected]; Nava kishore Manne <[email protected]>
Cc: Ronan Keryell <[email protected]>
Subject: Re: FPGA Manager - Partial Reconfiguration support for Xilinx Zynq- 7000Quoted 6 lines · Michal Simek
Hi,
Quoted 3 lines · Alper Yazar
Hi,
I asked the question on Xilinx forums about 1 months ago but didn't get any
response [1]. I hope that someone on this list may guide me.
Quoted 1 line
Quoted 1 line
I am creating Linux based images for Zynq-7000 devices by using Petalinux
2018.3 which is a set of build tools provided by Xilinx. For FPGA management, FPGA Manager is included by default. However it doesn't support partial reconfiguration for Zynq-7000 devices as stated [2]. I tested and verified that it doesn't work. I assumed that /drivers/fpga/zynq-fpga.c is the source code, checked it and noticed some comments about partial reconfig. AFAIK previous driver used by Xilinx before FPGA Manager whose source code file is
xilinx_devcfg.csupported partial reconfig. So I don't think that there is a hardware limitation since the previous solution was working on the same device. So I wonder why the newest method is less capable than the older one. I need partial reconfig support for the newest petalinux version. What should I do?Quoted 1 line
Quoted 1 line
a) Compile old
xilinx_devcfg.cdriver for Petalinux 2018.3 and disable FPGAManager.
Quoted 5 lines
Quoted 5 lines
b) Somehow patch FPGA Manager
c) Wait (how long?) Xilinx to solve this issue
Two names are listed as
MODULE_AUTHORofzynq-fpga.c: Moritz Fischerand Michal Simek. I don't know whether they are subscribed to this list or not.
Quoted 10 lines
Quoted 7 lines
[1]:
https://forums.xilinx.com/t5/Embedded-Linux/Partial-Reconfiguration-s
upport-in-Petalinux-2018-3-for-Zynq/td-p/934057
[2]:
https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18841645/Soluti
on+Zynq+PL+Programming+With+FPGA+ManagerNava: Can you please check if partial reconfiguration is still working? I see code in the driver.
Quoted 7 lines
Alper: Can you please use u-boot and check that your bitstreams are correct?
Also will be good to have some logs to see what it is happening.Thanks,
MichalHi Michal,
Sorry for late response. We checked U-boot and it worked without any problem. Our bitstreams are based on the Xilinx example project on partial reconfiguration.
1. Loading full bitstream using U-boot (successful):
Zynq> fatload mmc 0
0x4000000top.bitreading top.bit
4045663 bytes read in 235 ms (16.4 MiB/s)
Zynq> fpga loadb 0
0x40000004045663design filename = "top;UserID=0XFFFFFFFF;Version=2018.3" part number = "7z020clg484" date = "2019/01/30" time = "00:54:18" bytes in bitstream = 4045564
zynq_align_dma_buffer: Align buffer at 4000063 to 3ffff80(swap 1)2. Loading partial bitstream using U-boot (successful):
Zynq> fatload mmc 0
0x4000000S_knight_top_partial.bitreading S_knight_top_partial.bit
1238420 bytes read in 81 ms (14.6 MiB/s)
Zynq> fpga loadbp 0
0x40000001238420design filename = "top;UserID=0XFFFFFFFF;PARTIAL=TRUE;Version=2018.3" part number = "7z020clg484" date = "2019/01/30" time = "00:54:40" bytes in bitstream = 1238308
zynq_align_dma_buffer: Align buffer at 4000070 to 3ffff80(swap 1)Both of them worked fine.
3. Loading full bitstream on Petalinux 2018.3 (successful):
root@project4:~# mkdir -p /lib/firmwareroot@project4:~# cd /mntroot@project4:/mnt# cp top.bit.bin /lib/firmwareroot@project4:/mnt# echo top.bit.binQuoted 1 line
/sys/class/fpga_manager/fpga0/firmware
fpga_managerfpga0: writing top.bit.bin to Xilinx Zynq FPGA Manager4. Loading partial bitstream on Petalinux 2018.3 (NOT successful):
root@project4:/mnt# cp S_knight_top_partial.bit.bin /lib/firmwareroot@project4:/mnt# echo S_knight_top_partial.bit.binQuoted 1 line
/sys/class/fpga_manager/fpga0/firmware
fpga_managerfpga0: writing S_knight_top_partial.bit.bin to Xilinx Zynq FPGA Manager--- Wait few seconds ---
fpga_managerfpga0: Error after writing image data to FPGA-sh: echo: write error: Connection timed out
We also checked
fpga-mgr.hand saw the definiton: "#defineFPGA_MGR_PARTIAL_RECONFIGBIT(0)". For partial bitstream trials we
also tried setting this bit to 1 by "echo 1 >/sys/class/fpga_manager/fpga0/flags" command but this didn't affect the result.Since FPGA manager uses BIN file we convert BIT to BIN using SDK. U-boot works with BIT files. Is it possible that this conversion cause the problem? How should we convert BIT to BIN file?
Best,
Alper