OMAP3 EHCI USB HS mode performance issue
Hi All,
I am using OMAP3 based board, running git based kernel 2..6.28, and enabled "EHCI HCD (USB 2.0) support", PHY mode.
EHCI HS performance is measured using Catalyst, USB analyzer. I supposed to get 480 Mbits/s(theoritically), but getting around 80 Mbits/s for write and around 128 Mbits/s for read. Please suggest me some method/option to increase HS USB EHCI performance.
Thanks in advance
Regards
Ganeshan
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 4 lines
I am using OMAP3 based board, running git based kernel 2..6.28, and enabled "EHCI HCD (USB 2.0) support", PHY mode.
EHCI HS performance is measured using Catalyst, USB analyzer.
Are you doing bulk transfer to a pen drive to measure performance? If so then try using any USB hard disk. Which OMAP3 board are you using?
Ajay
Quoted 11 lines
I supposed to get 480
Mbits/s(theoritically), but getting around 80 Mbits/s for write and around 128 Mbits/s for read. Please suggest me some method/option to increase HS USB EHCI performance.Thanks in advance
Regards
Ganeshan
Quoted 4 lines
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Ajay,
I am transfering 100MB file to pen drive. I have tried with pen drive with different manufacturer (Tanscend, SanDisk, Kingston). I am using OMAP35x EVM.
Thanks & Regards
Ganeshan
----- Original Message ----
From: "Gupta, Ajay Kumar" <[email protected]>
To: Ganeshan N <[email protected]>; "[email protected]" <[email protected]>
Sent: Wednesday, February 4, 2009 10:02:15 AM
Subject: RE: OMAP3 EHCI USB HS mode performance issue
Quoted 4 lines
I am using OMAP3 based board, running git based kernel 2..6.28, and enabled "EHCI HCD (USB 2.0) support", PHY mode.
EHCI HS performance is measured using Catalyst, USB analyzer.
Are you doing bulk transfer to a pen drive to measure performance? If so then try using any USB hard disk. Which OMAP3 board are you using?
Ajay
Quoted 11 lines
I supposed to get 480
Mbits/s(theoritically), but getting around 80 Mbits/s for write and around 128 Mbits/s for read. Please suggest me some method/option to increase HS USB EHCI performance.Thanks in advance
Regards
Ganeshan
Quoted 4 lines
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 2 lines
I am transfering 100MB file to pen drive. I have tried with pen drive with different manufacturer (Tanscend, SanDisk, Kingston). I am using OMAP35x EVM.
We have observed lower throughput with pen drive so it's better if you take the performance numbers from any USB hard disk.
I think you are using OMAP35x EVM with Mistral daughter card. With Mistral DC, I am getting a read/write throughput of ~160Mbps on EHCI with USB HDD and CPUIDLE=off.
Regards,
Ajay
Quoted 4 lines
Thanks & Regards
Ganeshan
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Ajay,
Thanks a lot for your valuable inputs. I will keep you posted with my observations on this after testing with USB hard disk.
Thanks & Regards
Ganeshan
----- Original Message ----
From: "Gupta, Ajay Kumar" <[email protected]>
To: Ganeshan N <[email protected]>; "[email protected]" <[email protected]>
Sent: Wednesday, February 4, 2009 11:13:36 AM
Subject: RE: OMAP3 EHCI USB HS mode performance issue
Quoted 2 lines
I am transfering 100MB file to pen drive. I have tried with pen drive with different manufacturer (Tanscend, SanDisk, Kingston). I am using OMAP35x EVM.
We have observed lower throughput with pen drive so it's better if you take the performance numbers from any USB hard disk.
I think you are using OMAP35x EVM with Mistral daughter card. With Mistral DC, I am getting a read/write throughput of ~160Mbps on EHCI with USB HDD and CPUIDLE=off.
Regards,
Ajay
Quoted 4 lines
Thanks & Regards
Ganeshan
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html