Skip to contentSkip to conversation

U-Boot DM device tree and Linux device tree - what are the differences and why?

DISCUSSION Rudolf J Streif 2 participants 4 messages May 18, 2020 – May 19, 2020

lore
Share & tools
lore
#0 lore raw

I have a custom board that is similar to the i.MX6UL 14x14. One difference is that it has an eMMC rather than a SD card. Most recently I upgraded from u-boot 2019.07 to u-boot 2020.01 and now u-boot cannot detect the eMMC anymore.

For the 2019.07 version I did use CONFIG_FSL_ESDHC=y without CONFIG_DM_MMC. That does not work anymore. Compilation fails with "CONFIG_SYS_FSL_ESDHC_ADDR undefined". What has changed here and why?

Then I tried using CONFIG_FSL_USDHC=y and CONFIG_DM_MMC=y. I simply used the device tree from the Linux kernel which works just fine for the kernel. But it does not work for u-boot. It's hard to understand why. Why would the u-boot device tree be different than the kernel device tree? If that is even the issue.

It's an eMMC with 8-bit bus. Here are the definitions that work perfectly well for the Linux kernel:

&usdhc2 {
??? pinctrl-names = "default";
??? pinctrl-0 = <&pinctrl_usdhc2>;
??? bus-width = <8>;
??? max-frequency = <200000000>;
??? vmmc-supply = <&sw2_reg>;
??? mmc-ddr-1_8v;
??? cap-mmc-highspeed;
??? non-removable;
??? keep-power-in-suspend;
??? status = "okay";
};

??? ??? pinctrl_usdhc2: usdhc2grp {
??? ??? ??? fsl,pins = <
??? ??? ??? ??? MX6UL_PAD_NAND_RE_B__USDHC2_CLK??? ??? 0x1b0d9 /* eMMC_CLK */
??? ??? ??? ??? MX6UL_PAD_NAND_WE_B__USDHC2_CMD??? ??? 0x1b0d9 /* eMMC_CMD */
??? ??? ??? ??? MX6UL_PAD_NAND_ALE__USDHC2_RESET_B??? 0x1b0d9 /* eMMC_RST */ ??? ??? ??? ??? MX6UL_PAD_NAND_DATA00__USDHC2_DATA0??? 0x1b0d9 /* eMMC_DAT0 */
??? ??? ??? ??? MX6UL_PAD_NAND_DATA01__USDHC2_DATA1??? 0x1b0d9 /* eMMC_DAT1 */
??? ??? ??? ??? MX6UL_PAD_NAND_DATA02__USDHC2_DATA2??? 0x1b0d9 /* eMMC_DAT2 */
??? ??? ??? ??? MX6UL_PAD_NAND_DATA03__USDHC2_DATA3??? 0x1b0d9 /* eMMC_DAT3 */
??? ??? ??? ??? MX6UL_PAD_NAND_DATA04__USDHC2_DATA4??? 0x1b0d9 /* eMMC_DAT4 */
??? ??? ??? ??? MX6UL_PAD_NAND_DATA05__USDHC2_DATA5??? 0x1b0d9 /* eMMC_DAT5 */
??? ??? ??? ??? MX6UL_PAD_NAND_DATA06__USDHC2_DATA6??? 0x1b0d9 /* eMMC_DAT6 */
??? ??? ??? ??? MX6UL_PAD_NAND_DATA07__USDHC2_DATA7??? 0x1b0d9 /* eMMC_DAT7 */
??? ??? ??? >;
??? ??? };

Every time the eMMC is probed e.g 'mmc dev 1' it takes about a second and then the response is 'MMC: no card present'.

I appreciate the help.

Thank you,
Rudi

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200518/94fe42d0/attachment.sig>

#1 lore raw

I solved the problem with u-boot not recognizing the eMMC. The device tree is working now for u-boot.

However, i.MX6 is using SPL which is loaded into OCRAM. If I flash SPL and u-boot to a boot partition on the eMMC the boot ROM loads SPL just fine but then SPL cannot load u-boot from eMMC:

Trying to boot from MMC1
MMC: no card present
spl: mmc init failed with error: -123
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

If I enable CONFIG_SPL_DM=y and CONFIG_SPL_DM_MMC=y then I am getting this undefined reference (and a whole slew of other related to DM):

common/built-in.o:(.u_boot_list_2_uclass_2_usb_hub+0x8): undefined reference to `dm_scan_fdt_dev'

Even if I get this to link then the next question of course is if it will fit into the 68k OCRAM that the SoC has (the whole device tree infrastructure has a rather large footprint). It is hard to follow why the DM now is essentially enforced for storage media but does not seem to be tested with SPL.

Once again, I appreciate any pointer to a possible solution.

Rudi

Quoted 65 lines · Rudolf J Streif

I have a custom board that is similar to the i.MX6UL 14x14. One difference is that it has an eMMC rather than a SD card. Most recently I upgraded from u-boot 2019.07 to u-boot 2020.01 and now u-boot cannot detect the eMMC anymore.

For the 2019.07 version I did use CONFIG_FSL_ESDHC=y without CONFIG_DM_MMC. That does not work anymore. Compilation fails with "CONFIG_SYS_FSL_ESDHC_ADDR undefined". What has changed here and why?

Then I tried using CONFIG_FSL_USDHC=y and CONFIG_DM_MMC=y. I simply used the device tree from the Linux kernel which works just fine for the kernel. But it does not work for u-boot. It's hard to understand why. Why would the u-boot device tree be different than the kernel device tree? If that is even the issue.

It's an eMMC with 8-bit bus. Here are the definitions that work perfectly well for the Linux kernel:

&usdhc2 {
??? pinctrl-names = "default";
??? pinctrl-0 = <&pinctrl_usdhc2>;
??? bus-width = <8>;
??? max-frequency = <200000000>;
??? vmmc-supply = <&sw2_reg>;
??? mmc-ddr-1_8v;
??? cap-mmc-highspeed;
??? non-removable;
??? keep-power-in-suspend;
??? status = "okay";
};

??? ??? pinctrl_usdhc2: usdhc2grp {
??? ??? ??? fsl,pins = <
??? ??? ??? ??? MX6UL_PAD_NAND_RE_B__USDHC2_CLK??? ??? 0x1b0d9 /* eMMC_CLK */
??? ??? ??? ??? MX6UL_PAD_NAND_WE_B__USDHC2_CMD??? ??? 0x1b0d9 /* eMMC_CMD */
??? ??? ??? ??? MX6UL_PAD_NAND_ALE__USDHC2_RESET_B??? 0x1b0d9 /* eMMC_RST */ ??? ??? ??? ??? MX6UL_PAD_NAND_DATA00__USDHC2_DATA0??? 0x1b0d9 /* eMMC_DAT0 */
??? ??? ??? ??? MX6UL_PAD_NAND_DATA01__USDHC2_DATA1??? 0x1b0d9 /* eMMC_DAT1 */
??? ??? ??? ??? MX6UL_PAD_NAND_DATA02__USDHC2_DATA2??? 0x1b0d9 /* eMMC_DAT2 */
??? ??? ??? ??? MX6UL_PAD_NAND_DATA03__USDHC2_DATA3??? 0x1b0d9 /* eMMC_DAT3 */
??? ??? ??? ??? MX6UL_PAD_NAND_DATA04__USDHC2_DATA4??? 0x1b0d9 /* eMMC_DAT4 */
??? ??? ??? ??? MX6UL_PAD_NAND_DATA05__USDHC2_DATA5??? 0x1b0d9 /* eMMC_DAT5 */
??? ??? ??? ??? MX6UL_PAD_NAND_DATA06__USDHC2_DATA6??? 0x1b0d9 /* eMMC_DAT6 */
??? ??? ??? ??? MX6UL_PAD_NAND_DATA07__USDHC2_DATA7??? 0x1b0d9 /* eMMC_DAT7 */
??? ??? ??? >;
??? ??? };

Every time the eMMC is probed e.g 'mmc dev 1' it takes about a second and then the response is 'MMC: no card present'.

I appreciate the help.

Thank you,
Rudi

Signature · 12 lines
-----
Rudolf J Streif
CEO/CTO ibeeto
+1.855.442.3386 x700

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200518/f5732b0e/attachment.sig>
#2 lore raw

Hi Rudolf,

Quoted 17 lines · Rudolf J Streif

I solved the problem with u-boot not recognizing the eMMC. The device tree is working now for u-boot.

However, i.MX6 is using SPL which is loaded into OCRAM. If I flash SPL and u-boot to a boot partition on the eMMC the boot ROM loads SPL just fine but then SPL cannot load u-boot from eMMC:

Trying to boot from MMC1
MMC: no card present
spl: mmc init failed with error: -123
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

If I enable CONFIG_SPL_DM=y and CONFIG_SPL_DM_MMC=y then I am getting this undefined reference (and a whole slew of other related to DM):

Quoted 8 lines

common/built-in.o:(.u_boot_list_2_uclass_2_usb_hub+0x8): undefined reference to `dm_scan_fdt_dev'

Even if I get this to link then the next question of course is if it will fit into the 68k OCRAM that the SoC has (the whole device tree infrastructure has a rather large footprint). It is hard to follow why the DM now is essentially enforced for storage media but does not seem to be tested with SPL.

I had a similar issue on a pico-imx6ul board. I preferred to put the MMC initialization code in SPL rather than relying on DM as in SPL we are very tight in memory.

Please see this commit:
https://gitlab.denx.de/u-boot/u-boot/-/commit/9b8d9ec41a6f161d53d32bf71f79332236b44ba1

#3 lore raw

Hi Fabio

Quoted 28 lines · Fabio Estevam

Hi Rudolf,

Quoted 16 lines · Rudolf J Streif

I solved the problem with u-boot not recognizing the eMMC. The device tree is working now for u-boot.

However, i.MX6 is using SPL which is loaded into OCRAM. If I flash SPL and u-boot to a boot partition on the eMMC the boot ROM loads SPL just fine but then SPL cannot load u-boot from eMMC:

Trying to boot from MMC1
MMC: no card present
spl: mmc init failed with error: -123
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

If I enable CONFIG_SPL_DM=y and CONFIG_SPL_DM_MMC=y then I am getting this undefined reference (and a whole slew of other related to DM):

Quoted 8 lines

common/built-in.o:(.u_boot_list_2_uclass_2_usb_hub+0x8): undefined reference to `dm_scan_fdt_dev'

Even if I get this to link then the next question of course is if it will fit into the 68k OCRAM that the SoC has (the whole device tree infrastructure has a rather large footprint). It is hard to follow why the DM now is essentially enforced for storage media but does not seem to be tested with SPL.

Quoted 6 lines

I had a similar issue on a pico-imx6ul board. I preferred to put the MMC initialization code in SPL rather than relying on DM as in SPL we are very tight in memory.

Please see this commit:
https://gitlab.denx.de/u-boot/u-boot/-/commit/9b8d9ec41a6f161d53d32bf71f79332236b44ba1

Thank you so much. You pointed me into the right direction. I was able to find a solution for my board.

Much appreciated.

Rudi

Signature · 13 lines
-----
Rudolf J Streif
CEO/CTO ibeeto
+1.855.442.3386 x700


-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200519/21d9fa26/attachment.sig>