Sama7g5 Evaluation Kit support
v2 cover Sama7g5 Evaluation Kit support
Hello,
This series adds support for sama7g5 SoC DT and the sama7g5ek board. I kept the original incremental development for this board, with each commit's author and designated change, for traceability and for easier reviewing.
The series starts from a basic devicetree and ends with a fully functional board including SD-Card/MMC, i2c eeproms, ethernet.
Thanks,
Eugen
Changes in v2:
- fixed compatible for i2c eeprom, mac was not read correctly in latest u-boot version
- fixed some checkpatch warnings and some spacing
Claudiu Beznea (20):
board: atmel: sama7g5ek: add SYS_MALLOC_F_LEN to SYS_INIT_SP_ADDR
configs: sama7g5ek: set malloc pool to 68K
configs: sama7g5ek: enable pll driver
ARM: dts: sama7g5: move clock frequencies for xtals in board file
ARM: dts: sama7g5: add slow rc and main rc oscillators
ARM: dts: sama7g5: add u-boot,dm-pre-reloc bindings for xtals
ARM: dts: sama7g5: add slow clock bindings
ARM: dts: sama7g5: add PMC bindings
ARM: dts: sama7g5: switch to PMC bindings
configs: sama7g5: enable CONFIG_CPU
ARM: dts: sama7g5: add CPU bindings
configs: sama7g5: use PIT64B
ARM: dts: sama7g5: enable autoboot
ARM: dts: sama7g5: add pit64b support
configs: sama7g5ek: enable mii command
ARM: dts: sama7g5: add GMAC0
ARM: dts: sama7g5: add GMAC1
board: atmel: sama7g5ek: increase arp timeout and retry count
configs: sama7g5ek: enable support for KSZ9131
configs: sama7g5ek: enable CCF
Eugen Hristev (13):
ARM: dts: sama7g5: add initial DT for sama7g5 SoC
board: atmel: sama7g5ek: add initial support for sama7g5ek
ARM: dts: at91: sama7g5: add pinctrl node
ARM: dts: at91: sama7g5ek: add pinctrl for sdmmc1 and flx3
ARM: dts: at91: sama7g5: add assigned clocks for sdmmc1
ARM: dts: at91: sama7g5: add node for sdmmc0
ARM: dts: at91: sama7g5ek: enable sdmmc0 with pinctrl
board: atmel: sama7g5ek: clean-up header bootcommand
configs: sama7g5: add mmc config for sdmmc0
ARM: dts: at91: sama7g5: add flexcom1 and i2c subnode
ARM: dts: sama7g5ek: add i2c1 bus and eeproms
board: atmel: sama7g5ek: add support for MAC address retreival
configs: sama7g5ek: add i2c and eeprom
Nicolas Ferre (1):
ARM: dts: sama7g5ek: fix TXC pin configuration
arch/arm/dts/Makefile | 3 + arch/arm/dts/sama7g5.dtsi | 170 ++++++++++++++++++++++++ arch/arm/dts/sama7g5ek-u-boot.dtsi | 65 ++++++++++ arch/arm/dts/sama7g5ek.dts | 202 +++++++++++++++++++++++++++++ arch/arm/mach-at91/Kconfig | 8 ++ board/atmel/sama7g5ek/Kconfig | 15 +++ board/atmel/sama7g5ek/MAINTAINERS | 8 ++ board/atmel/sama7g5ek/Makefile | 7 + board/atmel/sama7g5ek/sama7g5ek.c | 76 +++++++++++ configs/sama7g5ek_mmc1_defconfig | 70 ++++++++++ configs/sama7g5ek_mmc_defconfig | 70 ++++++++++ include/configs/sama7g5ek.h | 45 +++++++ 12 files changed, 739 insertions(+) create mode 100644 arch/arm/dts/sama7g5.dtsi create mode 100644 arch/arm/dts/sama7g5ek-u-boot.dtsi create mode 100644 arch/arm/dts/sama7g5ek.dts create mode 100644 board/atmel/sama7g5ek/Kconfig create mode 100644 board/atmel/sama7g5ek/MAINTAINERS create mode 100644 board/atmel/sama7g5ek/Makefile create mode 100644 board/atmel/sama7g5ek/sama7g5ek.c create mode 100644 configs/sama7g5ek_mmc1_defconfig create mode 100644 configs/sama7g5ek_mmc_defconfig create mode 100644 include/configs/sama7g5ek.h
Signature · 1 line
2.25.1
PATCH v2 1/34 ARM: dts: sama7g5: add initial DT for sama7g5 SoC
Add initial basic devicetree for sama7g5 SoC
--- arch/arm/dts/sama7g5.dtsi | 65 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 65 insertions(+) create mode 100644 arch/arm/dts/sama7g5.dtsi
arch/arm/dts/sama7g5.dtsi new file +65 -0
@@ -0,0 +1,65 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * sama7g5.dtsi - Device Tree Include file for SAMA7G5 SoC. + * + * Copyright (C) 2020 Microchip Technology Inc. and its subsidiaries + * + * Author: Eugen Hristev <[email protected]> + * Author: Claudiu Beznea <[email protected]> + * + */ + +#include "skeleton.dtsi" + +/ { + model = "Microchip SAMA7G5 family SoC"; + compatible = "microchip,sama7g5"; + + clocks { + slow_xtal: slow_xtal { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + }; + + main_xtal: main_xtal { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + }; + + mck: mck { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <200000000>; + }; + }; + + ahb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + + apb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + + sdmmc1: sdio-host at e1208000 { + compatible = "microchip,sama7g5-sdhci"; + reg = <0xe1208000 0x300>; + clocks = <&mck>, <&mck>, <&mck>; + clock-names = "hclock", "multclk", "baseclk"; + status = "disabled"; + }; + + uart0: serial at e1824200 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xe1824200 0x200>; + clocks = <&mck>; + clock-names = "usart"; + status = "disabled"; + }; + }; + }; +};
Signature · 1 line
2.25.1
PATCH v2 2/34 board: atmel: sama7g5ek: add initial support for sama7g5ek
In reply to Eugen HristevAdd initial support for sama7g5 evaluation kit board.
--- arch/arm/dts/Makefile | 3 ++ arch/arm/dts/sama7g5ek-u-boot.dtsi | 33 +++++++++++++++ arch/arm/dts/sama7g5ek.dts | 39 +++++++++++++++++ arch/arm/mach-at91/Kconfig | 8 ++++ board/atmel/sama7g5ek/Kconfig | 15 +++++++ board/atmel/sama7g5ek/MAINTAINERS | 7 +++ board/atmel/sama7g5ek/Makefile | 7 +++ board/atmel/sama7g5ek/sama7g5ek.c | 68 ++++++++++++++++++++++++++++++ configs/sama7g5ek_mmc1_defconfig | 59 ++++++++++++++++++++++++++ include/configs/sama7g5ek.h | 46 ++++++++++++++++++++ 10 files changed, 285 insertions(+) create mode 100644 arch/arm/dts/sama7g5ek-u-boot.dtsi create mode 100644 arch/arm/dts/sama7g5ek.dts create mode 100644 board/atmel/sama7g5ek/Kconfig create mode 100644 board/atmel/sama7g5ek/MAINTAINERS create mode 100644 board/atmel/sama7g5ek/Makefile create mode 100644 board/atmel/sama7g5ek/sama7g5ek.c create mode 100644 configs/sama7g5ek_mmc1_defconfig create mode 100644 include/configs/sama7g5ek.h
arch/arm/dts/Makefile +3 -0
@@ -891,6 +891,9 @@ dtb-$(CONFIG_TARGET_OMAP4_SDP4430) += \ dtb-$(CONFIG_TARGET_OMAP5_UEVM) += \ omap5-uevm.dtb +dtb-$(CONFIG_TARGET_SAMA7G5EK) += \ + sama7g5ek.dtb + dtb-$(CONFIG_TARGET_SAMA5D2_PTC_EK) += \ at91-sama5d2_ptc_ek.dtb
arch/arm/dts/sama7g5ek-u-boot.dtsi new file +33 -0
@@ -0,0 +1,33 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * sama7g5ek-u-boot.dts - Device Tree file for SAMA7G5 SoC u-boot properties. + * + * Copyright (C) 2020 Microchip Technology Inc. and its subsidiaries + * + * Author: Eugen Hristev <[email protected]> + * Author: Claudiu Beznea <[email protected]> + * + */ + +/ { + chosen { + u-boot,dm-pre-reloc; + }; + + ahb { + u-boot,dm-pre-reloc; + + apb { + u-boot,dm-pre-reloc; + }; + }; +}; + +&uart0 { + u-boot,dm-pre-reloc; +}; + +&mck { + u-boot,dm-pre-reloc; +}; +
arch/arm/dts/sama7g5ek.dts new file +39 -0
@@ -0,0 +1,39 @@ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +/* + * sama7g5ek.dts - Device Tree file for SAMA7G5 EK + * SAMA7G5 Evaluation Kit + * + * Copyright (c) 2020, Microchip Technology Inc. + * 2020, Eugen Hristev <[email protected]> + * 2020, Claudiu Beznea <[email protected]> + */ +/dts-v1/; +#include "sama7g5.dtsi" +#include "sama7g5-pinfunc.h" + +/ { + model = "Microchip SAMA7G5 Evaluation Kit"; + compatible = "microchip,sama7g5ek", "microchip,sama7g54", "microchip,sama7g5", "microchip,sama7"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + ahb { + + apb { + sdmmc1: sdio-host at e1208000 { + bus-width = <4>; + status = "okay"; + }; + + uart0: serial at e1824200 { + status = "okay"; + }; + }; + }; +};
arch/arm/mach-at91/Kconfig +8 -0
@@ -265,6 +265,13 @@ config TARGET_CORVUS select SUPPORT_SPL imply CMD_DM +config TARGET_SAMA7G5EK + bool "SAMA7G5 EK board" + select SAMA7G5 + select BOARD_EARLY_INIT_F + select BOARD_LATE_INIT + + config TARGET_TAURUS bool "Support taurus" select AT91SAM9G20
@@ -327,6 +334,7 @@ source "board/atmel/at91sam9n12ek/Kconfig" source "board/atmel/at91sam9rlek/Kconfig" source "board/atmel/at91sam9x5ek/Kconfig" source "board/atmel/sam9x60ek/Kconfig" +source "board/atmel/sama7g5ek/Kconfig" source "board/atmel/sama5d2_ptc_ek/Kconfig" source "board/atmel/sama5d2_xplained/Kconfig" source "board/atmel/sama5d27_som1_ek/Kconfig"
board/atmel/sama7g5ek/Kconfig new file +15 -0
@@ -0,0 +1,15 @@ +if TARGET_SAMA7G5EK + +config SYS_BOARD + default "sama7g5ek" + +config SYS_VENDOR + default "atmel" + +config SYS_SOC + default "at91" + +config SYS_CONFIG_NAME + default "sama7g5ek" + +endif
board/atmel/sama7g5ek/MAINTAINERS new file +7 -0
@@ -0,0 +1,7 @@ +SAMA7G5 EK BOARD +M: Eugen Hristev <[email protected]> +S: Maintained +F: board/atmel/sama7g5ek.c +F: include/configs/sama7g5ek.h +F: configs/sama7g5ek_mmc1_defconfig +
board/atmel/sama7g5ek/Makefile new file +7 -0
@@ -0,0 +1,7 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2020 Microchip Technology Inc. +# Eugen Hristev <[email protected]> +# + +obj-y += sama7g5ek.o
board/atmel/sama7g5ek/sama7g5ek.c new file +68 -0
68 lines not on this page · raw message
configs/sama7g5ek_mmc1_defconfig new file +59 -0
59 lines not on this page · raw message
include/configs/sama7g5ek.h new file +46 -0
46 lines not on this page · raw message
Signature · 1 line
2.25.1
PATCH v2 3/34 board: atmel: sama7g5ek: add SYS_MALLOC_F_LEN to SYS_INIT_SP_ADDR
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Heap base address is computed based on SYS_INIT_SP_ADDR by subtracting the SYS_MALLOC_F_LEN value in board_init_f_init_reserve().
--- include/configs/sama7g5ek.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
include/configs/sama7g5ek.h +2 -1
@@ -20,7 +20,8 @@#define CONFIG_SYS_INIT_SP_ADDR 0x218000#else #define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE) + (CONFIG_SYS_SDRAM_BASE + 16 * 1024 + CONFIG_SYS_MALLOC_F_LEN - \ + GENERATED_GBL_DATA_SIZE)#endif #define CONFIG_SYS_LOAD_ADDR 0x62000000/* load address */
Signature · 1 line
2.25.1
PATCH v2 4/34 configs: sama7g5ek: set malloc pool to 68K
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Set malloc pool to 68K for sama7g5ek.
--- configs/sama7g5ek_mmc1_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/sama7g5ek_mmc1_defconfig +1 -0
@@ -3,6 +3,7 @@ CONFIG_ARCH_AT91=y CONFIG_SYS_TEXT_BASE=0x66f00000 CONFIG_TARGET_SAMA7G5EK=y CONFIG_NR_DRAM_BANKS=1 +CONFIG_SYS_MALLOC_F_LEN=0x11000 CONFIG_ENV_SIZE=0x4000 CONFIG_DM_GPIO=y CONFIG_DEBUG_UART_BOARD_INIT=y
Signature · 1 line
2.25.1
PATCH v2 5/34 configs: sama7g5ek: enable pll driver
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Enable PLL driver for SAMA7G5.
--- configs/sama7g5ek_mmc1_defconfig | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
configs/sama7g5ek_mmc1_defconfig +2 -1
@@ -5,7 +5,6 @@ CONFIG_TARGET_SAMA7G5EK=y CONFIG_NR_DRAM_BANKS=1 CONFIG_SYS_MALLOC_F_LEN=0x11000 CONFIG_ENV_SIZE=0x4000 -CONFIG_DM_GPIO=y CONFIG_DEBUG_UART_BOARD_INIT=y CONFIG_DEBUG_UART_BASE=0xe1824200 CONFIG_DEBUG_UART_CLOCK=200000000
@@ -42,6 +41,8 @@ CONFIG_CLK=y CONFIG_CLK_AT91=y CONFIG_AT91_UTMI=y CONFIG_AT91_GENERIC_CLK=y +CONFIG_AT91_SAM9X60_PLL=y +CONFIG_DM_GPIO=y CONFIG_ATMEL_PIO4=y CONFIG_DM_I2C=y CONFIG_DM_MMC=y
Signature · 1 line
2.25.1
PATCH v2 6/34 ARM: dts: sama7g5: move clock frequencies for xtals in board file
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Move clock frequencies for crystals on board specific files.
--- arch/arm/dts/sama7g5.dtsi | 2 -- arch/arm/dts/sama7g5ek.dts | 10 ++++++++++ 2 files changed, 10 insertions(+), 2 deletions(-)
arch/arm/dts/sama7g5.dtsi +0 -2
@@ -19,13 +19,11 @@ slow_xtal: slow_xtal { compatible = "fixed-clock"; #clock-cells = <0>; - clock-frequency = <0>; }; main_xtal: main_xtal { compatible = "fixed-clock"; #clock-cells = <0>; - clock-frequency = <0>; }; mck: mck {
arch/arm/dts/sama7g5ek.dts +10 -0
@@ -23,6 +23,16 @@ stdout-path = "serial0:115200n8"; }; + clocks { + slow_xtal: slow_xtal { + clock-frequency = <32768>; + }; + + main_xtal: main_xtal { + clock-frequency = <24000000>; + }; + }; + ahb { apb {
Signature · 1 line
2.25.1
PATCH v2 7/34 ARM: dts: sama7g5: add slow rc and main rc oscillators
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Add slow rc and main rc oscillators to dtsi.
--- arch/arm/dts/sama7g5.dtsi | 12 ++++++++++++ arch/arm/dts/sama7g5ek-u-boot.dtsi | 8 ++++++++ 2 files changed, 20 insertions(+)
arch/arm/dts/sama7g5.dtsi +12 -0
@@ -16,6 +16,18 @@ compatible = "microchip,sama7g5"; clocks { + slow_rc_osc: slow_rc_osc { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <18500>; + }; + + main_rc: main_rc { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <12000000>; + }; + slow_xtal: slow_xtal { compatible = "fixed-clock"; #clock-cells = <0>;
arch/arm/dts/sama7g5ek-u-boot.dtsi +8 -0
@@ -23,6 +23,14 @@ }; }; +&main_rc { + u-boot,dm-pre-reloc; +}; + +&slow_rc_osc { + u-boot,dm-pre-reloc; +}; + &uart0 { u-boot,dm-pre-reloc; };
Signature · 1 line
2.25.1
PATCH v3 7/34 ARM: dts: sama7g5: add slow rc and main rc oscillators
From: Claudiu Beznea <[email protected]>
Add slow rc and main rc oscillators to dtsi.
---
Changes in v3:
- adapt slow rc frequency to real value: 32 kHz
arch/arm/dts/sama7g5.dtsi | 12 ++++++++++++ arch/arm/dts/sama7g5ek-u-boot.dtsi | 8 ++++++++ 2 files changed, 20 insertions(+)
arch/arm/dts/sama7g5.dtsi +12 -0
@@ -16,6 +16,18 @@ compatible = "microchip,sama7g5"; clocks { + slow_rc_osc: slow_rc_osc { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32000>; + }; + + main_rc: main_rc { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <12000000>; + }; + slow_xtal: slow_xtal { compatible = "fixed-clock"; #clock-cells = <0>;
arch/arm/dts/sama7g5ek-u-boot.dtsi +8 -0
@@ -23,6 +23,14 @@ }; }; +&main_rc { + u-boot,dm-pre-reloc; +}; + +&slow_rc_osc { + u-boot,dm-pre-reloc; +}; + &uart0 { u-boot,dm-pre-reloc; };
Signature · 1 line
2.25.1
PATCH v2 8/34 ARM: dts: sama7g5: add u-boot, dm-pre-reloc bindings for xtals
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Add dm-pre-reloc DT binding property for cristals.
--- arch/arm/dts/sama7g5ek-u-boot.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+)
arch/arm/dts/sama7g5ek-u-boot.dtsi +8 -0
@@ -27,10 +27,18 @@ u-boot,dm-pre-reloc; }; +&main_xtal { + u-boot,dm-pre-reloc; +}; + &slow_rc_osc { u-boot,dm-pre-reloc; }; +&slow_xtal { + u-boot,dm-pre-reloc; +}; + &uart0 { u-boot,dm-pre-reloc; };
Signature · 1 line
2.25.1
PATCH v2 9/34 ARM: dts: sama7g5: add slow clock bindings
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Add DT bindings for slow clock driver.
--- arch/arm/dts/sama7g5.dtsi | 7 +++++++ 1 file changed, 7 insertions(+)
arch/arm/dts/sama7g5.dtsi +7 -0
@@ -55,6 +55,13 @@ #address-cells = <1>; #size-cells = <1>; + clk32: sckc at e001d050 { + compatible = "microchip,sam9x60-sckc"; + reg = <0xe001d050 0x4>; + clocks = <&slow_rc_osc>, <&slow_xtal>; + #clock-cells = <1>; + }; + sdmmc1: sdio-host at e1208000 { compatible = "microchip,sama7g5-sdhci"; reg = <0xe1208000 0x300>;
Signature · 1 line
2.25.1
PATCH v2 10/34 ARM: dts: sama7g5: add PMC bindings
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Add DT bindings for PMC driver.
--- arch/arm/dts/sama7g5.dtsi | 9 +++++++++ arch/arm/dts/sama7g5ek-u-boot.dtsi | 4 ++++ 2 files changed, 13 insertions(+)
arch/arm/dts/sama7g5.dtsi +9 -0
@@ -55,6 +55,15 @@ #address-cells = <1>; #size-cells = <1>; + pmc: pmc at e0018000 { + compatible = "microchip,sama7g5-pmc"; + reg = <0xe0018000 0x200>; + #clock-cells = <2>; + clocks = <&clk32 1>, <&clk32 0>, <&main_xtal>, <&main_rc>; + clock-names = "td_slck", "md_slck", "main_xtal", "main_rc"; + status = "okay"; + }; + clk32: sckc at e001d050 { compatible = "microchip,sam9x60-sckc"; reg = <0xe001d050 0x4>;
arch/arm/dts/sama7g5ek-u-boot.dtsi +4 -0
@@ -31,6 +31,10 @@ u-boot,dm-pre-reloc; }; +&pmc { + u-boot,dm-pre-reloc; +}; + &slow_rc_osc { u-boot,dm-pre-reloc; };
Signature · 1 line
2.25.1
PATCH v2 11/34 ARM: dts: sama7g5: switch to PMC bindings
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Get rid of software defined MCK and switch to PMC bindings for IPs currently present in device tree.
--- arch/arm/dts/sama7g5.dtsi | 13 ++++--------- arch/arm/dts/sama7g5ek-u-boot.dtsi | 4 ---- 2 files changed, 4 insertions(+), 13 deletions(-)
arch/arm/dts/sama7g5.dtsi +4 -9
@@ -10,6 +10,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/clk/at91.h> / { model = "Microchip SAMA7G5 family SoC";
@@ -37,12 +38,6 @@ compatible = "fixed-clock"; #clock-cells = <0>; }; - - mck: mck { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <200000000>; - }; }; ahb {
@@ -74,15 +69,15 @@ sdmmc1: sdio-host at e1208000 { compatible = "microchip,sama7g5-sdhci"; reg = <0xe1208000 0x300>; - clocks = <&mck>, <&mck>, <&mck>; - clock-names = "hclock", "multclk", "baseclk"; + clocks = <&pmc PMC_TYPE_PERIPHERAL 81>, <&pmc PMC_TYPE_GCK 81>; + clock-names = "hclock", "multclk"; status = "disabled"; }; uart0: serial at e1824200 { compatible = "atmel,at91sam9260-usart"; reg = <0xe1824200 0x200>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 41>; clock-names = "usart"; status = "disabled"; };
arch/arm/dts/sama7g5ek-u-boot.dtsi +0 -4
@@ -47,7 +47,3 @@ u-boot,dm-pre-reloc; }; -&mck { - u-boot,dm-pre-reloc; -}; -
Signature · 1 line
2.25.1
PATCH v2 12/34 configs: sama7g5: enable CONFIG_CPU
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Enable CONFIG_CPU.
--- configs/sama7g5ek_mmc1_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/sama7g5ek_mmc1_defconfig +1 -0
@@ -42,6 +42,7 @@ CONFIG_CLK_AT91=y CONFIG_AT91_UTMI=y CONFIG_AT91_GENERIC_CLK=y CONFIG_AT91_SAM9X60_PLL=y +CONFIG_CPU=y CONFIG_DM_GPIO=y CONFIG_ATMEL_PIO4=y CONFIG_DM_I2C=y
Signature · 1 line
2.25.1
PATCH v2 13/34 ARM: dts: sama7g5: add CPU bindings
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Add CPU DT bindings.
--- arch/arm/dts/sama7g5.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+)
arch/arm/dts/sama7g5.dtsi +12 -0
@@ -40,6 +40,18 @@ }; }; + cpus { + #address-cells = <1>; + #size-cells = <0>; + + A7_0: cpu at 0 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + clocks = <&pmc PMC_TYPE_CORE 8>, <&pmc PMC_TYPE_CORE 22>, <&main_xtal>; + clock-names = "cpu", "master", "xtal"; + }; + }; + ahb { compatible = "simple-bus"; #address-cells = <1>;
Signature · 1 line
2.25.1
PATCH v2 14/34 configs: sama7g5: use PIT64B
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Use PIT64B driver. ATMEL_PIT is not available for SAMA7G5.
--- configs/sama7g5ek_mmc1_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/sama7g5ek_mmc1_defconfig +1 -0
@@ -58,5 +58,6 @@ CONFIG_DM_SERIAL=y CONFIG_DEBUG_UART_ANNOUNCE=y CONFIG_ATMEL_USART=y CONFIG_TIMER=y +CONFIG_MCHP_PIT64B_TIMER=y CONFIG_OF_LIBFDT_OVERLAY=y # CONFIG_EFI_LOADER_HII is not set
Signature · 1 line
2.25.1
PATCH v2 15/34 ARM: dts: sama7g5: enable autoboot
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Enable autoboot.
--- configs/sama7g5ek_mmc1_defconfig | 1 - 1 file changed, 1 deletion(-)
configs/sama7g5ek_mmc1_defconfig +0 -1
@@ -16,7 +16,6 @@ CONFIG_SD_BOOT=y CONFIG_USE_BOOTARGS=y CONFIG_MISC_INIT_R=y CONFIG_HUSH_PARSER=y -# CONFIG_AUTOBOOT is not set CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMI is not set CONFIG_CMD_MD5SUM=y
Signature · 1 line
2.25.1
PATCH v2 16/34 ARM: dts: sama7g5: add pit64b support
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Add DT bindings for PIT64B driver.
--- arch/arm/dts/sama7g5.dtsi | 8 ++++++++ arch/arm/dts/sama7g5ek-u-boot.dtsi | 4 ++++ 2 files changed, 12 insertions(+)
arch/arm/dts/sama7g5.dtsi +8 -0
@@ -86,6 +86,14 @@ status = "disabled"; }; + pit64b0: timer at e1800000 { + compatible = "microchip,sama7g5-pit64b"; + reg = <0xe1800000 0x4000>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 70>, <&pmc PMC_TYPE_GCK 70>; + clock-names = "pclk", "gclk"; + status = "okay"; + }; + uart0: serial at e1824200 { compatible = "atmel,at91sam9260-usart"; reg = <0xe1824200 0x200>;
arch/arm/dts/sama7g5ek-u-boot.dtsi +4 -0
@@ -31,6 +31,10 @@ u-boot,dm-pre-reloc; }; +&pit64b0 { + u-boot,dm-pre-reloc; +}; + &pmc { u-boot,dm-pre-reloc; };
Signature · 1 line
2.25.1
PATCH v2 17/34 ARM: dts: at91: sama7g5: add pinctrl node
In reply to Eugen HristevAdd pioA pinctrl node.
--- arch/arm/dts/sama7g5.dtsi | 13 +++++++++++++ arch/arm/dts/sama7g5ek-u-boot.dtsi | 8 ++++++++ 2 files changed, 21 insertions(+)
arch/arm/dts/sama7g5.dtsi +13 -0
@@ -62,6 +62,19 @@ #address-cells = <1>; #size-cells = <1>; + pioA: pinctrl at e0014000 { + compatible = "atmel,sama5d2-gpio"; + reg = <0xe0014000 0x800>; + gpio-controller; + #gpio-cells = <2>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 11>; + status = "okay"; + + pinctrl: pinctrl_default { + compatible = "microchip,sama7g5-pinctrl"; + }; + }; + pmc: pmc at e0018000 { compatible = "microchip,sama7g5-pmc"; reg = <0xe0018000 0x200>;
arch/arm/dts/sama7g5ek-u-boot.dtsi +8 -0
@@ -31,6 +31,14 @@ u-boot,dm-pre-reloc; }; +&pioA { + u-boot,dm-pre-reloc; + + pinctrl { + u-boot,dm-pre-reloc; + }; +}; + &pit64b0 { u-boot,dm-pre-reloc; };
Signature · 1 line
2.25.1
PATCH v2 18/34 ARM: dts: at91: sama7g5ek: add pinctrl for sdmmc1 and flx3
In reply to Eugen HristevAdd pinctrl for sdmmc1 and flx3.
--- arch/arm/dts/sama7g5ek-u-boot.dtsi | 4 ++++ arch/arm/dts/sama7g5ek.dts | 30 ++++++++++++++++++++++++++++++ 2 files changed, 34 insertions(+)
arch/arm/dts/sama7g5ek-u-boot.dtsi +4 -0
@@ -39,6 +39,10 @@ }; }; +&pinctrl_flx3_default { + u-boot,dm-pre-reloc; +}; + &pit64b0 { u-boot,dm-pre-reloc; };
arch/arm/dts/sama7g5ek.dts +30 -0
@@ -38,12 +38,42 @@ apb { sdmmc1: sdio-host at e1208000 { bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdmmc1_cmd_data_default + &pinctrl_sdmmc1_ck_cd_rstn_vddsel_default>; status = "okay"; }; uart0: serial at e1824200 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flx3_default>; status = "okay"; }; }; }; }; + +&pinctrl { + pinctrl_flx3_default: flx3_default { + pinmux = <PIN_PD16__FLEXCOM3_IO0>, + <PIN_PD17__FLEXCOM3_IO1>; + bias-disable; + }; + + pinctrl_sdmmc1_cmd_data_default: sdmmc1_cmd_data_default { + pinmux = <PIN_PB29__SDMMC1_CMD>, + <PIN_PB31__SDMMC1_DAT0>, + <PIN_PC0__SDMMC1_DAT1>, + <PIN_PC1__SDMMC1_DAT2>, + <PIN_PC2__SDMMC1_DAT3>; + bias-pull-up; + }; + + pinctrl_sdmmc1_ck_cd_rstn_vddsel_default: sdmmc1_ck_cd_rstn_vddsel_default { + pinmux = <PIN_PB30__SDMMC1_CK>, + <PIN_PB28__SDMMC1_RSTN>, + <PIN_PC5__SDMMC1_1V8SEL>, + <PIN_PC4__SDMMC1_CD>; + bias-pull-up; + }; +};
Signature · 1 line
2.25.1
PATCH v2 19/34 configs: sama7g5ek: enable mii command
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Enable mii command as ethernet's PHY specific programming is based on it.
--- configs/sama7g5ek_mmc1_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/sama7g5ek_mmc1_defconfig +1 -0
@@ -29,6 +29,7 @@ CONFIG_CMD_I2C=y # CONFIG_CMD_LOADS is not set CONFIG_CMD_MMC=y CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_EXT4=y CONFIG_CMD_FAT=y
Signature · 1 line
2.25.1
PATCH v2 20/34 ARM: dts: sama7g5: add GMAC0
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Add GMAC0.
--- arch/arm/dts/sama7g5.dtsi | 11 +++++++++++ arch/arm/dts/sama7g5ek.dts | 32 ++++++++++++++++++++++++++++++++ 2 files changed, 43 insertions(+)
arch/arm/dts/sama7g5.dtsi +11 -0
@@ -114,6 +114,17 @@ clock-names = "usart"; status = "disabled"; }; + + gmac0: ethernet at e2800000 { + compatible = "cdns,sama7g5-gem"; + reg = <0xe2800000 0x4000>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 51>, <&pmc PMC_TYPE_PERIPHERAL 51>, <&pmc PMC_TYPE_GCK 51>; + clock-names = "hclk", "pclk", "tx_clk"; + assigned-clocks = <&pmc PMC_TYPE_GCK 51>; + assigned-clock-parents = <&pmc PMC_TYPE_CORE 21>; /* eth pll div. */ + assigned-clock-rates = <125000000>; + status = "disabled"; + }; }; }; };
arch/arm/dts/sama7g5ek.dts +32 -0
@@ -53,6 +53,19 @@ }; }; +&gmac0 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gmac0_default>; + phy-mode = "rgmii-id"; + status = "okay"; + + ethernet-phy at 7 { + reg = <0x7>; + }; +}; + &pinctrl { pinctrl_flx3_default: flx3_default { pinmux = <PIN_PD16__FLEXCOM3_IO0>,
@@ -76,4 +89,23 @@ <PIN_PC4__SDMMC1_CD>; bias-pull-up; }; + + pinctrl_gmac0_default: gmac0_default { + pinmux = <PIN_PA16__G0_TX0>, + <PIN_PA17__G0_TX1>, + <PIN_PA26__G0_TX2>, + <PIN_PA27__G0_TX3>, + <PIN_PA19__G0_RX0>, + <PIN_PA20__G0_RX1>, + <PIN_PA28__G0_RX2>, + <PIN_PA29__G0_RX3>, + <PIN_PA15__G0_TXEN>, + <PIN_PA24__G0_TXCK>, + <PIN_PA30__G0_RXCK>, + <PIN_PA18__G0_RXDV>, + <PIN_PA22__G0_MDC>, + <PIN_PA23__G0_MDIO>, + <PIN_PA25__G0_125CK>; + bias-disable; + }; };
Signature · 1 line
2.25.1
PATCH v2 21/34 ARM: dts: sama7g5: add GMAC1
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Add GMAC1.
--- arch/arm/dts/sama7g5.dtsi | 8 ++++++++ arch/arm/dts/sama7g5ek.dts | 27 +++++++++++++++++++++++++++ 2 files changed, 35 insertions(+)
arch/arm/dts/sama7g5.dtsi +8 -0
@@ -125,6 +125,14 @@ assigned-clock-rates = <125000000>; status = "disabled"; }; + + gmac1: ethernet at e2804000 { + compatible = "cdns,sama7g5-emac"; + reg = <0xe2804000 0x1000>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 52>, <&pmc PMC_TYPE_PERIPHERAL 52>; + clock-names = "pclk", "hclk"; + status = "disabled"; + }; }; }; };
arch/arm/dts/sama7g5ek.dts +27 -0
@@ -66,6 +66,19 @@ }; }; +&gmac1 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gmac1_default>; + phy-mode = "rmii"; + status = "okay"; + + ethernet-phy at 0 { + reg = <0x0>; + }; +}; + &pinctrl { pinctrl_flx3_default: flx3_default { pinmux = <PIN_PD16__FLEXCOM3_IO0>,
@@ -108,4 +121,18 @@ <PIN_PA25__G0_125CK>; bias-disable; }; + + pinctrl_gmac1_default: gmac1_default { + pinmux = <PIN_PD30__G1_TXCK>, + <PIN_PD22__G1_TX0>, + <PIN_PD23__G1_TX1>, + <PIN_PD21__G1_TXEN>, + <PIN_PD25__G1_RX0>, + <PIN_PD26__G1_RX1>, + <PIN_PD27__G1_RXER>, + <PIN_PD24__G1_RXDV>, + <PIN_PD28__G1_MDC>, + <PIN_PD29__G1_MDIO>; + bias-disable; + }; };
Signature · 1 line
2.25.1
PATCH v2 22/34 board: atmel: sama7g5ek: increase arp timeout and retry count
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Increase ARP timeout and retry count as this will increase the speed of communication.
--- include/configs/sama7g5ek.h | 3 +++ 1 file changed, 3 insertions(+)
include/configs/sama7g5ek.h +3 -0
@@ -44,4 +44,7 @@/* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) +#define CONFIG_ARP_TIMEOUT 200 +#define CONFIG_NET_RETRY_COUNT 50 +#endif
Signature · 1 line
2.25.1
PATCH v2 23/34 configs: sama7g5ek: enable support for KSZ9131
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Enable support for KSZ9131.
--- configs/sama7g5ek_mmc1_defconfig | 2 ++ 1 file changed, 2 insertions(+)
configs/sama7g5ek_mmc1_defconfig +2 -0
@@ -49,6 +49,8 @@ CONFIG_DM_I2C=y CONFIG_DM_MMC=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ATMEL=y +CONFIG_PHY_MICREL=y +CONFIG_PHY_MICREL_KSZ90X1=y CONFIG_DM_ETH=y CONFIG_MACB=y CONFIG_PINCTRL=y
Signature · 1 line
2.25.1
PATCH v2 24/34 configs: sama7g5ek: enable CCF
In reply to Eugen HristevFrom: Claudiu Beznea <[email protected]>
Enable CCF for SAMA7G5.
--- configs/sama7g5ek_mmc1_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/sama7g5ek_mmc1_defconfig +1 -0
@@ -38,6 +38,7 @@ CONFIG_ENV_IS_IN_FAT=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM=y CONFIG_CLK=y +CONFIG_CLK_CCF=y CONFIG_CLK_AT91=y CONFIG_AT91_UTMI=y CONFIG_AT91_GENERIC_CLK=y
Signature · 1 line
2.25.1
PATCH v2 25/34 ARM: dts: at91: sama7g5: add assigned clocks for sdmmc1
In reply to Eugen HristevSDMMC1 requires clock specification with assigned-clocks, such that the PMC will know which parent to assign and the initial start-up frequency.
--- arch/arm/dts/sama7g5.dtsi | 3 +++ 1 file changed, 3 insertions(+)
arch/arm/dts/sama7g5.dtsi +3 -0
@@ -96,6 +96,9 @@ reg = <0xe1208000 0x300>; clocks = <&pmc PMC_TYPE_PERIPHERAL 81>, <&pmc PMC_TYPE_GCK 81>; clock-names = "hclock", "multclk"; + assigned-clocks = <&pmc PMC_TYPE_GCK 81>; + assigned-clock-rates = <200000000>; + assigned-clock-parents = <&pmc PMC_TYPE_CORE 10>; /* sys pll div. */ status = "disabled"; };
Signature · 1 line
2.25.1
PATCH v2 26/34 ARM: dts: at91: sama7g5: add node for sdmmc0
In reply to Eugen HristevAdd node for sdmmc0 block.
--- arch/arm/dts/sama7g5.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)
arch/arm/dts/sama7g5.dtsi +11 -0
@@ -91,6 +91,17 @@ #clock-cells = <1>; }; + sdmmc0: sdio-host at e1204000 { + compatible = "microchip,sama7g5-sdhci"; + reg = <0xe1204000 0x300>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 80>, <&pmc PMC_TYPE_GCK 80>; + clock-names = "hclock", "multclk"; + assigned-clocks = <&pmc PMC_TYPE_GCK 80>; + assigned-clock-rates = <200000000>; + assigned-clock-parents = <&pmc PMC_TYPE_CORE 10>; /* sys pll div. */ + status = "disabled"; + }; + sdmmc1: sdio-host at e1208000 { compatible = "microchip,sama7g5-sdhci"; reg = <0xe1208000 0x300>;
Signature · 1 line
2.25.1
PATCH v2 27/34 ARM: dts: at91: sama7g5ek: enable sdmmc0 with pinctrl
In reply to Eugen HristevEnable sdmmc0 on this board. A non-removable eMMC is connected on this block.
Configure pincontrol accordingly.
--- arch/arm/dts/sama7g5ek.dts | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+)
arch/arm/dts/sama7g5ek.dts +30 -0
@@ -36,6 +36,15 @@ ahb { apb { + sdmmc0: sdio-host at e1204000 { + bus-width = <8>; + non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdmmc0_cmd_data_default + &pinctrl_sdmmc0_ck_rstn_ds_cd_default>; + status = "okay"; + }; + sdmmc1: sdio-host at e1208000 { bus-width = <4>; pinctrl-names = "default";
@@ -86,6 +95,27 @@ bias-disable; }; + pinctrl_sdmmc0_cmd_data_default: sdmmc0_cmd_data_default { + pinmux = <PIN_PA1__SDMMC0_CMD>, + <PIN_PA3__SDMMC0_DAT0>, + <PIN_PA4__SDMMC0_DAT1>, + <PIN_PA5__SDMMC0_DAT2>, + <PIN_PA6__SDMMC0_DAT3>, + <PIN_PA7__SDMMC0_DAT4>, + <PIN_PA8__SDMMC0_DAT5>, + <PIN_PA9__SDMMC0_DAT6>, + <PIN_PA10__SDMMC0_DAT7>; + bias-pull-up; + }; + + pinctrl_sdmmc0_ck_rstn_ds_cd_default: sdmmc0_ck_rstn_ds_cd_default { + pinmux = <PIN_PA0__SDMMC0_CK>, + <PIN_PA2__SDMMC0_RSTN>, + <PIN_PA11__SDMMC0_DS>, + <PIN_PA14__SDMMC0_CD>; + bias-pull-up; + }; + pinctrl_sdmmc1_cmd_data_default: sdmmc1_cmd_data_default { pinmux = <PIN_PB29__SDMMC1_CMD>, <PIN_PB31__SDMMC1_DAT0>,
Signature · 1 line
2.25.1
PATCH v2 28/34 board: atmel: sama7g5ek: clean-up header bootcommand
In reply to Eugen HristevClean-up boot command to use the predefined device and part for FAT environment.
According to this device and partition, select the proper boot media.
--- include/configs/sama7g5ek.h | 11 +++-------- 1 file changed, 3 insertions(+), 8 deletions(-)
include/configs/sama7g5ek.h +3 -8
@@ -29,16 +29,11 @@#undef CONFIG_BOOTCOMMAND#ifdef CONFIG_SD_BOOT /* u-boot env in sd/mmc card */ -#define FAT_ENV_INTERFACE "mmc" -#define FAT_ENV_DEVICE_AND_PART "0" -#define FAT_ENV_FILE "uboot.env" +/* bootstrap + u-boot + env in sd card */ -#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x61000000 at91-sama7g5ek.dtb; " \ - "fatload mmc 0:1 0x62000000 zImage; " \ +#define CONFIG_BOOTCOMMAND "fatload mmc " CONFIG_ENV_FAT_DEVICE_AND_PART " 0x61000000 at91-sama7g5ek.dtb; " \ + "fatload mmc " CONFIG_ENV_FAT_DEVICE_AND_PART " 0x62000000 zImage; " \ "bootz 0x62000000 - 0x61000000" -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTARGS \ - "console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait"#endif /* Size of malloc() pool */
Signature · 1 line
2.25.1
PATCH v2 29/34 configs: sama7g5: add mmc config for sdmmc0
In reply to Eugen HristevAdd new config for storing environment from sdmmc0. Also clean-up sama7g5ek_emmc1 to point to the proper mmc device.
--- board/atmel/sama7g5ek/MAINTAINERS | 1 + configs/sama7g5ek_mmc1_defconfig | 7 ++-- configs/sama7g5ek_mmc_defconfig | 67 +++++++++++++++++++++++++++++++ 3 files changed, 72 insertions(+), 3 deletions(-) create mode 100644 configs/sama7g5ek_mmc_defconfig
board/atmel/sama7g5ek/MAINTAINERS +1 -0
@@ -4,4 +4,5 @@ S: Maintained F: board/atmel/sama7g5ek.c F: include/configs/sama7g5ek.h F: configs/sama7g5ek_mmc1_defconfig +F: configs/sama7g5ek_mmc_defconfig
configs/sama7g5ek_mmc1_defconfig +4 -3
@@ -2,9 +2,10 @@ CONFIG_ARM=y CONFIG_ARCH_AT91=y CONFIG_SYS_TEXT_BASE=0x66f00000 CONFIG_TARGET_SAMA7G5EK=y -CONFIG_NR_DRAM_BANKS=1 CONFIG_SYS_MALLOC_F_LEN=0x11000 +CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x4000 +CONFIG_DM_GPIO=y CONFIG_DEBUG_UART_BOARD_INIT=y CONFIG_DEBUG_UART_BASE=0xe1824200 CONFIG_DEBUG_UART_CLOCK=200000000
@@ -14,6 +15,7 @@ CONFIG_ENV_VARS_UBOOT_CONFIG=y CONFIG_FIT=y CONFIG_SD_BOOT=y CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk1p2 rw rootwait" CONFIG_MISC_INIT_R=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y
@@ -35,6 +37,7 @@ CONFIG_CMD_EXT4=y CONFIG_CMD_FAT=y CONFIG_OF_CONTROL=y CONFIG_ENV_IS_IN_FAT=y +CONFIG_ENV_FAT_DEVICE_AND_PART="1:1" CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM=y CONFIG_CLK=y
@@ -44,7 +47,6 @@ CONFIG_AT91_UTMI=y CONFIG_AT91_GENERIC_CLK=y CONFIG_AT91_SAM9X60_PLL=y CONFIG_CPU=y -CONFIG_DM_GPIO=y CONFIG_ATMEL_PIO4=y CONFIG_DM_I2C=y CONFIG_DM_MMC=y
@@ -56,7 +58,6 @@ CONFIG_DM_ETH=y CONFIG_MACB=y CONFIG_PINCTRL=y CONFIG_PINCTRL_AT91PIO4=y -# CONFIG_RAM_ROCKCHIP_DEBUG is not set CONFIG_DM_SERIAL=y CONFIG_DEBUG_UART_ANNOUNCE=y CONFIG_ATMEL_USART=y
configs/sama7g5ek_mmc_defconfig new file +67 -0
67 lines not on this page · raw message
Signature · 1 line
2.25.1
PATCH v2 30/34 ARM: dts: at91: sama7g5: add flexcom1 and i2c subnode
In reply to Eugen HristevAdd flexcom1 and i2c subnode.
--- arch/arm/dts/sama7g5.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)
arch/arm/dts/sama7g5.dtsi +18 -0
@@ -121,6 +121,24 @@ status = "okay"; }; + flx1: flexcom at e181c000 { + compatible = "atmel,sama5d2-flexcom"; + reg = <0xe181c000 0x200>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 39>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0xe181c000 0x800>; + status = "disabled"; + + i2c1: i2c at 600 { + compatible = "atmel,sama5d2-i2c"; + reg = <0x600 0x200>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 39>; + }; + }; + uart0: serial at e1824200 { compatible = "atmel,at91sam9260-usart"; reg = <0xe1824200 0x200>;
Signature · 1 line
2.25.1
PATCH v2 31/34 ARM: dts: sama7g5ek: add i2c1 bus and eeproms
In reply to Eugen HristevAdd node for flx1 i2c1 subnode (and alias to bus 0) This bus has two eeprom devices connected.
--- arch/arm/dts/sama7g5ek.dts | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+)
arch/arm/dts/sama7g5ek.dts +30 -0
@@ -17,6 +17,7 @@ aliases { serial0 = &uart0; + i2c0 = &i2c1; }; chosen {
@@ -62,6 +63,29 @@ }; }; +&flx1 { + atmel,flexcom-mode = <3>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flx1_default>; + status = "okay"; + + eeprom at 52 { + compatible = "microchip,24aa02e48"; + reg = <0x52>; + pagesize = <16>; + }; + + eeprom at 53 { + compatible = "microchip,24aa02e48"; + reg = <0x53>; + pagesize = <16>; + }; +}; + &gmac0 { #address-cells = <1>; #size-cells = <0>;
@@ -89,6 +113,12 @@ }; &pinctrl { + pinctrl_flx1_default: flx1_default { + pinmux = <PIN_PC9__FLEXCOM1_IO0>, + <PIN_PC10__FLEXCOM1_IO1>; + bias-disable; + }; + pinctrl_flx3_default: flx3_default { pinmux = <PIN_PD16__FLEXCOM3_IO0>, <PIN_PD17__FLEXCOM3_IO1>;
Signature · 1 line
2.25.1
PATCH v2 32/34 board: atmel: sama7g5ek: add support for MAC address retreival
In reply to Eugen HristevObtain two MAC addresses from the two EEPROMs and configure the two available Ethernet interfaces accordingly.
--- board/atmel/sama7g5ek/sama7g5ek.c | 18 +++++++++++++----- 1 file changed, 13 insertions(+), 5 deletions(-)
board/atmel/sama7g5ek/sama7g5ek.c +13 -5
@@ -46,6 +46,19 @@ int board_early_init_f(void)return 0 ; } +#define MAC24AA_MAC_OFFSET 0xfa + +#if (IS_ENABLED (CONFIG_MISC_INIT_R )) +int misc_init_r (void ) +{ +#if (IS_ENABLED (CONFIG_I2C_EEPROM )) +at91_set_ethaddr (MAC24AA_MAC_OFFSET ); +at91_set_eth1addr (MAC24AA_MAC_OFFSET ); +#endif +return 0 ; +} +#endif +int board_init (void ) {/* address of boot parameters */
@@ -61,8 +74,3 @@ int dram_init(void)return 0 ; } -int misc_init_r (void ) -{ -return 0 ; -} -
Signature · 1 line
2.25.1
PATCH v2 33/34 configs: sama7g5ek: add i2c and eeprom
In reply to Eugen HristevAdd drivers for flexcom, i2c and eeproms
--- configs/sama7g5ek_mmc1_defconfig | 3 +++ configs/sama7g5ek_mmc_defconfig | 3 +++ 2 files changed, 6 insertions(+)
configs/sama7g5ek_mmc1_defconfig +3 -0
@@ -49,6 +49,9 @@ CONFIG_AT91_SAM9X60_PLL=y CONFIG_CPU=y CONFIG_ATMEL_PIO4=y CONFIG_DM_I2C=y +CONFIG_SYS_I2C_AT91=y +CONFIG_I2C_EEPROM=y +CONFIG_MICROCHIP_FLEXCOM=y CONFIG_DM_MMC=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ATMEL=y
configs/sama7g5ek_mmc_defconfig +3 -0
@@ -49,6 +49,9 @@ CONFIG_AT91_SAM9X60_PLL=y CONFIG_CPU=y CONFIG_ATMEL_PIO4=y CONFIG_DM_I2C=y +CONFIG_SYS_I2C_AT91=y +CONFIG_I2C_EEPROM=y +CONFIG_MICROCHIP_FLEXCOM=y CONFIG_DM_MMC=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ATMEL=y
Signature · 1 line
2.25.1
PATCH v2 34/34 ARM: dts: sama7g5ek: fix TXC pin configuration
In reply to Eugen HristevFrom: Nicolas Ferre <[email protected]>
TXC line is directly connected from the SoC to the KSZ9131 PHY. There is a transient state on this signal, before configuring it to RGMII, which leads to packet transmit being blocked.
Keeping a pull-up when muxing this pin as function A (G0_TXCK) fixes the issue.
--- arch/arm/dts/sama7g5ek.dts | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)
arch/arm/dts/sama7g5ek.dts +6 -2
@@ -90,7 +90,7 @@ #address-cells = <1>; #size-cells = <0>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gmac0_default>; + pinctrl-0 = <&pinctrl_gmac0_default &pinctrl_gmac0_txc_default>; phy-mode = "rgmii-id"; status = "okay";
@@ -173,7 +173,6 @@ <PIN_PA28__G0_RX2>, <PIN_PA29__G0_RX3>, <PIN_PA15__G0_TXEN>, - <PIN_PA24__G0_TXCK>, <PIN_PA30__G0_RXCK>, <PIN_PA18__G0_RXDV>, <PIN_PA22__G0_MDC>,
@@ -182,6 +181,11 @@ bias-disable; }; + pinctrl_gmac0_txc_default: gmac0_txc_default { + pinmux = <PIN_PA24__G0_TXCK>; + bias-pull-up; + }; + pinctrl_gmac1_default: gmac1_default { pinmux = <PIN_PD30__G1_TXCK>, <PIN_PD22__G1_TX0>,
Signature · 1 line
2.25.1
v2 cover Sama7g5 Evaluation Kit support
In reply to Eugen HristevQuoted 70 lines · Eugen Hristev
Hello,
This series adds support for sama7g5 SoC DT and the sama7g5ek board. I kept the original incremental development for this board, with each commit's author and designated change, for traceability and for easier reviewing.
The series starts from a basic devicetree and ends with a fully functional board including SD-Card/MMC, i2c eeproms, ethernet.
Thanks,
EugenChanges in v2:
- fixed compatible for i2c eeprom, mac was not read correctly in latest u-boot version
- fixed some checkpatch warnings and some spacingClaudiu Beznea (20):
board: atmel: sama7g5ek: addSYS_MALLOC_F_LENtoSYS_INIT_SP_ADDR
configs: sama7g5ek: set malloc pool to 68K
configs: sama7g5ek: enable pll driver
ARM: dts: sama7g5: move clock frequencies for xtals in board file
ARM: dts: sama7g5: add slow rc and main rc oscillators
ARM: dts: sama7g5: add u-boot,dm-pre-reloc bindings for xtals
ARM: dts: sama7g5: add slow clock bindings
ARM: dts: sama7g5: add PMC bindings
ARM: dts: sama7g5: switch to PMC bindings
configs: sama7g5: enableCONFIG_CPU
ARM: dts: sama7g5: add CPU bindings
configs: sama7g5: use PIT64B
ARM: dts: sama7g5: enable autoboot
ARM: dts: sama7g5: add pit64b support
configs: sama7g5ek: enable mii command
ARM: dts: sama7g5: add GMAC0
ARM: dts: sama7g5: add GMAC1
board: atmel: sama7g5ek: increase arp timeout and retry count
configs: sama7g5ek: enable support for KSZ9131
configs: sama7g5ek: enable CCFEugen Hristev (13):
ARM: dts: sama7g5: add initial DT for sama7g5 SoC
board: atmel: sama7g5ek: add initial support for sama7g5ek
ARM: dts: at91: sama7g5: add pinctrl node
ARM: dts: at91: sama7g5ek: add pinctrl for sdmmc1 and flx3
ARM: dts: at91: sama7g5: add assigned clocks for sdmmc1
ARM: dts: at91: sama7g5: add node for sdmmc0
ARM: dts: at91: sama7g5ek: enable sdmmc0 with pinctrl
board: atmel: sama7g5ek: clean-up header bootcommand
configs: sama7g5: add mmc config for sdmmc0
ARM: dts: at91: sama7g5: add flexcom1 and i2c subnode
ARM: dts: sama7g5ek: add i2c1 bus and eeproms
board: atmel: sama7g5ek: add support for MAC address retreival
configs: sama7g5ek: add i2c and eepromNicolas Ferre (1):
ARM: dts: sama7g5ek: fix TXC pin configurationarch/arm/dts/Makefile | 3 + arch/arm/dts/sama7g5.dtsi | 170 ++++++++++++++++++++++++ arch/arm/dts/sama7g5ek-u-boot.dtsi | 65 ++++++++++ arch/arm/dts/sama7g5ek.dts | 202 +++++++++++++++++++++++++++++ arch/arm/mach-at91/Kconfig | 8 ++ board/atmel/sama7g5ek/Kconfig | 15 +++ board/atmel/sama7g5ek/MAINTAINERS | 8 ++ board/atmel/sama7g5ek/Makefile | 7 + board/atmel/sama7g5ek/sama7g5ek.c | 76 +++++++++++ configs/sama7g5ek_mmc1_defconfig | 70 ++++++++++ configs/sama7g5ek_mmc_defconfig | 70 ++++++++++ include/configs/sama7g5ek.h | 45 +++++++ 12 files changed, 739 insertions(+)
Quoted 11 lines
create mode 100644
arch/arm/dts/sama7g5.dtsicreate mode 100644arch/arm/dts/sama7g5ek-u-boot.dtsicreate mode 100644arch/arm/dts/sama7g5ek.dtscreate mode 100644 board/atmel/sama7g5ek/Kconfig create mode 100644 board/atmel/sama7g5ek/MAINTAINERS create mode 100644 board/atmel/sama7g5ek/Makefile create mode 100644board/atmel/sama7g5ek/sama7g5ek.ccreate mode 100644 configs/sama7g5ek_mmc1_defconfig create mode 100644 configs/sama7g5ek_mmc_defconfig create mode 100644include/configs/sama7g5ek.h
Applied to u-boot-atmel/master