Skip to contentSkip to conversation

nfs mount for PQ2FADS-ZU board

U-Boot-Users Nethra 2 participants 2 messages Nov 18, 2006

lore
Share & tools
lore

Nethra

author
#0 lore raw

hi,

linux kernel starts successfully when fallowing commands are used...

=>setenv bootargs root=/dev/ram
=>setenv bootcmd 'tftpboot 0x1000000 dhcpbootpdis.img;\tftpboot 0x1200000 ramdisk.new;\bootm 0x1000000 0x1200000;\'
=>run bootcmd

during nfs mounting................

=>setenv bootcmd 'tftp 0x100000 dhcpbootpdis.img;\bootm 0x100000'
=>setenv bootargs 'root=/dev/nfs rw nfsroot=192.168.178.110:/opt/montavista/pro/devkit/ppc/82xx//opt/montavista/pro/devkit/ppc/82xx/target ;\tcp
ip=192.168.178.234:192.168.178.110:192.168.178.6:255.255.255.0:pq2fads::off'

when i do bootcmd..kernel uncompress fails.

this is shown below...
=>run bootcmd
Using FCC2 ETHERNET device
TFTP from server 192.168.178.110; our IP address is 192.168.178.234 Filename 'dhcpbootpdis.img'.
Load address: 0x100000
Loading: #################################################################

         #################################################################
         #######################################################
done
Bytes transferred = 942283 (e60cb hex)
## Booting image at 00100000 ...
   Image Name:   Linux-2.6.10_mvl401-8272ads
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    942219 Bytes = 920.1 kB

Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... Error: inflate() returned -3
GUNZIP ERROR - must RESET b

U-Boot 1.1.1 (Nov 2 2006 - 06:21:13)

MPC8260 Reset Status:

MPC8260 Clock Configuration
- Bus-to-Core Mult 3x, VCO Div 4, 60x Bus Freq 16-50 , Core Freq 50-150
- dfbrg 1, corecnf 0x10, busdf 3, cpmdf 1, plldf 0, pllmf 3

 - vco_out  400000000, scc_clk  100000000, brg_clk   25000000
 - cpu_clk  300000000, cpm_clk  200000000, bus_clk  100000000
CPU:   MPC8260 (HiP7 Rev 13, Mask 0.1 1K49M) at 300 MHz
Board: Motorola CASHFADS
DRAM:  32 MB
FLASH:  8 MB
In:    serial
Out:   serial
Err:   serial
Net:   FCC2 ETHERNET
Hit any key to stop autoboot:  0

can anyone tell me what is the problem..
thanks in advance..

Nethra

Signature · 2 lines
View this message in context: http://www.nabble.com/nfs-mount-for-PQ2FADS-ZU-board-tf2658418.html#a7415366
Sent from the Uboot - Users mailing list archive at Nabble.com.
#1 lore raw
Quoted 2 lines · In message <[email protected]> you wrote:

## Booting image at 00100000 ...

----------------------^^^^^^^^

Quoted 8 lines
   Image Name:   Linux-2.6.10_mvl401-8272ads
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    942219 Bytes = 920.1 kB

Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... Error: inflate() returned -3
GUNZIP ERROR - must RESET b

^^^^^^^^^^^^^^^^^^^^^^^^^^^^

Quoted 1 line

can anyone tell me what is the problem..

May I ask why you did not bother to read the FAQ?

It's answered here:
http://www.denx.de/wiki/view/DULG/LinuxUncompressingError

Best regards,

Wolfgang Denk

Signature · 3 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
core error - bus dumped