sunxi: add support for Tanix TX6
Subsystems (2)
cover sunxi: add support for Tanix TX6
This series introduces Tanix TX6 TV box support based on Allwinner H6 SoC. First patch syncs H6 DT files from Linux 5.11-rc1 release and second one adds support for Tanix TX6 board.
Please take a look.
Best regards,
Jernej
Jernej Skrabec (2):
ARM: dts: sunxi: h6: Update DT files
sunxi: Add support for Tanix TX6
arch/arm/dts/Makefile | 3 +- arch/arm/dts/sun50i-h6-beelink-gs1.dts | 70 +++- arch/arm/dts/sun50i-h6-cpu-opp.dtsi | 117 +++++++ arch/arm/dts/sun50i-h6-orangepi-lite2.dts | 71 +++- arch/arm/dts/sun50i-h6-orangepi.dtsi | 72 +++- arch/arm/dts/sun50i-h6-pine-h64.dts | 102 ++++-- arch/arm/dts/sun50i-h6-tanix-tx6.dts | 124 +++++++ arch/arm/dts/sun50i-h6.dtsi | 394 ++++++++++++++++++++-- board/sunxi/MAINTAINERS | 6 + 9 files changed, 890 insertions(+), 69 deletions(-) create mode 100644 arch/arm/dts/sun50i-h6-cpu-opp.dtsi create mode 100644 arch/arm/dts/sun50i-h6-tanix-tx6.dts
Signature · 1 line
2.30.0
PATCH 1/2 ARM: dts: sunxi: h6: Update DT files
Updated H6 DT files are based on Linux 5.11-rc1 release.
--- arch/arm/dts/sun50i-h6-beelink-gs1.dts | 70 +++- arch/arm/dts/sun50i-h6-cpu-opp.dtsi | 117 +++++++ arch/arm/dts/sun50i-h6-orangepi-lite2.dts | 71 +++- arch/arm/dts/sun50i-h6-orangepi.dtsi | 72 +++- arch/arm/dts/sun50i-h6-pine-h64.dts | 102 ++++-- arch/arm/dts/sun50i-h6.dtsi | 394 ++++++++++++++++++++-- 6 files changed, 758 insertions(+), 68 deletions(-) create mode 100644 arch/arm/dts/sun50i-h6-cpu-opp.dtsi
arch/arm/dts/sun50i-h6-beelink-gs1.dts +64 -6
@@ -1,11 +1,10 @@ -// SPDX-License-Identifier: (GPL-2.0+ or MIT) -/* - * Copyright (C) 2019 Cl?ment P?ron <[email protected]> - */ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2019 Cl?ment P?ron <[email protected]> /dts-v1/; #include "sun50i-h6.dtsi" +#include "sun50i-h6-cpu-opp.dtsi" #include <dt-bindings/gpio/gpio.h>
@@ -25,6 +24,7 @@ connector { compatible = "hdmi-connector"; type = "a"; + ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ port { hdmi_con_in: endpoint {
@@ -33,6 +33,13 @@ }; }; + ext_osc32k: ext_osc32k_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "ext_osc32k"; + }; + leds { compatible = "gpio-leds";
@@ -51,12 +58,38 @@ regulator-max-microvolt = <5000000>; regulator-always-on; }; + + sound-spdif { + compatible = "simple-audio-card"; + simple-audio-card,name = "sun50i-h6-spdif"; + + simple-audio-card,cpu { + sound-dai = <&spdif>; + }; + + simple-audio-card,codec { + sound-dai = <&spdif_out>; + }; + }; + + spdif_out: spdif-out { + #sound-dai-cells = <0>; + compatible = "linux,spdif-dit"; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdca>; }; &de { status = "okay"; }; +&dwc3 { + status = "okay"; +}; + &ehci0 { status = "okay"; };
@@ -64,12 +97,17 @@ &emac { pinctrl-names = "default"; pinctrl-0 = <&ext_rgmii_pins>; - phy-mode = "rgmii"; + phy-mode = "rgmii-id"; phy-handle = <&ext_rgmii_phy>; phy-supply = <®_aldo2>; status = "okay"; }; +&gpu { + mali-supply = <®_dcdcc>; + status = "okay"; +}; + &hdmi { status = "okay"; };
@@ -201,13 +239,16 @@ reg_dcdca: dcdca { regulator-always-on; regulator-min-microvolt = <810000>; - regulator-max-microvolt = <1080000>; + regulator-max-microvolt = <1160000>; + regulator-ramp-delay = <2500>; regulator-name = "vdd-cpu"; }; reg_dcdcc: dcdcc { + regulator-enable-ramp-delay = <32000>; regulator-min-microvolt = <810000>; regulator-max-microvolt = <1080000>; + regulator-ramp-delay = <2500>; regulator-name = "vdd-gpu"; };
@@ -232,6 +273,11 @@ }; }; +&r_ir { + linux,rc-map-name = "rc-beelink-gs1"; + status = "okay"; +}; + &r_pio { /* * PL0 and PL1 are used for PMIC I2C
@@ -243,6 +289,14 @@ vcc-pm-supply = <®_aldo1>; }; +&rtc { + clocks = <&ext_osc32k>; +}; + +&spdif { + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ph_pins>;
@@ -258,3 +312,7 @@ usb0_vbus-supply = <®_vcc5v>; status = "okay"; }; + +&usb3phy { + status = "okay"; +};
arch/arm/dts/sun50i-h6-cpu-opp.dtsi new file +117 -0
117 lines not on this page · raw message
arch/arm/dts/sun50i-h6-orangepi-lite2.dts +67 -4
78 lines not on this page · raw message
arch/arm/dts/sun50i-h6-orangepi.dtsi +66 -6
117 lines not on this page · raw message
arch/arm/dts/sun50i-h6-pine-h64.dts +79 -23
175 lines not on this page · raw message
arch/arm/dts/sun50i-h6.dtsi +365 -29
592 lines not on this page · raw message
Signature · 1 line
2.30.0
PATCH 2/2 sunxi: Add support for Tanix TX6
In reply to Jernej SkrabecThis commit adds support for Tanix TX6 TV box, based on H6. It's low end H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other peripherals.
DT file is taken from Linux 5.11-rc1 release.
--- arch/arm/dts/Makefile | 3 +- arch/arm/dts/sun50i-h6-tanix-tx6.dts | 124 +++++++++++++++++++++++++++ board/sunxi/MAINTAINERS | 6 ++ 3 files changed, 132 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/sun50i-h6-tanix-tx6.dts
arch/arm/dts/Makefile +2 -1
@@ -607,7 +607,8 @@ dtb-$(CONFIG_MACH_SUN50I_H6) += \ sun50i-h6-beelink-gs1.dtb \ sun50i-h6-orangepi-lite2.dtb \ sun50i-h6-orangepi-one-plus.dtb \ - sun50i-h6-pine-h64.dtb + sun50i-h6-pine-h64.dtb \ + sun50i-h6-tanix-tx6.dtb dtb-$(CONFIG_MACH_SUN50I) += \ sun50i-a64-amarula-relic.dtb \ sun50i-a64-bananapi-m64.dtb \
arch/arm/dts/sun50i-h6-tanix-tx6.dts new file +124 -0
124 lines not on this page · raw message
board/sunxi/MAINTAINERS +6 -0
@@ -489,6 +489,12 @@ S: Maintained F: configs/Sunchip_CX-A99_defconfig W: https://linux-sunxi.org/Sunchip_CX-A99 +TANIX TX6 BOARD +M: Jernej Skrabec <[email protected]> +S: Maintained +F: configs/tanix_tx6_defconfig +W: https://linux-sunxi.org/Tanix_TX6 + TBS A711 BOARD M: Maxime Ripard <[email protected]> S: Maintained
Signature · 1 line
2.30.0
cover sunxi: add support for Tanix TX6
In reply to Jernej SkrabecDne nedelja, 03. januar 2021 ob 10:56:52 CET je Jernej Skrabec napisal(a):
Quoted 8 lines
This series introduces Tanix TX6 TV box support based on Allwinner H6 SoC. First patch syncs H6 DT files from Linux 5.11-rc1 release and second one adds support for Tanix TX6 board.
Please take a look.
Best regards,
Jernej
Please disregard, I forgot to include board defconfig. I sent v2 with fix.
Regards,
Jernej