nand: mxc: Prepare to add support for i.MX5
Subsystems (6)
PATCH v5 1/8 nand: mxc: Prepare to add support for i.MX5
Add some abstraction to NFC defitnitions so that some parts of the current code can also be used for future i.MX5 code.
Clean up a few things by the way.
---
Changes in v5: None
Changes in v4: None
Changes in v3:
- Separate code reformatting from behavioral changes.
Changes in v2:
- Fix warning for unused tmp variable in board_nand_init() for NFC V1.
drivers/mtd/nand/mxc_nand.c | 92 +++++++++++++++++++++--------------------- include/fsl_nfc.h | 72 ++++++++++++--------------------- nand_spl/nand_boot_fsl_nfc.c | 47 +++++++++++---------- 3 files changed, 97 insertions(+), 114 deletions(-)
drivers/mtd/nand/mxc_nand.c +46 -46
@@ -150,7 +150,7 @@ static uint32_t *mxc_nand_memcpy32(uint32_t *dest, uint32_t *source, size_t size/* * This function polls the NANDFC to wait for the basic operation to -* complete by checking the INT bit of config2 register. +* complete by checking the INT bit. */ static void wait_op_done (struct mxc_nand_host *host,int max_retries,uint16_t param)
@@ -158,10 +158,10 @@ static void wait_op_done(struct mxc_nand_host *host, int max_retries,uint32_t tmp;while (max_retries-- >0 ) { -if (readw (&host->regs->config2) &NFC_INT ) { - tmp =readw (&host->regs->config2); - tmp &= ~NFC_INT ; -writew (tmp, &host->regs->config2); + tmp =readnfc (&host->regs->config2); +if (tmp &NFC_V1_V2_CONFIG2_INT ) { + tmp &= ~NFC_V1_V2_CONFIG2_INT ; +writenfc (tmp, &host->regs->config2);break ; }udelay (1 );
@@ -180,8 +180,8 @@ static void send_cmd(struct mxc_nand_host *host, uint16_t cmd) {MTDDEBUG (MTD_DEBUG_LEVEL3 ,"send_cmd(host, 0x%x)\n" , cmd); -writew (cmd, &host->regs->flash_cmd); -writew (NFC_CMD , &host->regs->config2); +writenfc (cmd, &host->regs->flash_cmd); +writenfc (NFC_CMD , &host->regs->operation);/* Wait for operation to complete */ wait_op_done (host,TROP_US_DELAY , cmd);
@@ -196,8 +196,8 @@ static void send_addr(struct mxc_nand_host *host, uint16_t addr) {MTDDEBUG (MTD_DEBUG_LEVEL3 ,"send_addr(host, 0x%x)\n" , addr); -writew (addr, &host->regs->flash_addr); -writew (NFC_ADDR , &host->regs->config2); +writenfc (addr, &host->regs->flash_addr); +writenfc (NFC_ADDR , &host->regs->operation);/* Wait for operation to complete */ wait_op_done (host,TROP_US_DELAY , addr);
@@ -229,19 +229,19 @@ static void send_prog_page(struct mxc_nand_host *host, uint8_t buf_id, } } -writew (buf_id, &host->regs->buf_addr); +writenfc (buf_id, &host->regs->buf_addr);/* Configure spare or page+spare access */ if (!host->pagesize_2k) { -uint16_t config1 =readw (&host->regs->config1); +uint16_t config1 =readnfc (&host->regs->config1);if (spare_only) - config1 |=NFC_SP_EN ; + config1 |=NFC_CONFIG1_SP_EN ;else - config1 &= ~NFC_SP_EN ; -writew (config1, &host->regs->config1); + config1 &= ~NFC_CONFIG1_SP_EN ; +writenfc (config1, &host->regs->config1); } -writew (NFC_INPUT , &host->regs->config2); +writenfc (NFC_INPUT , &host->regs->operation);/* Wait for operation to complete */ wait_op_done (host,TROP_US_DELAY , spare_only);
@@ -256,19 +256,19 @@ static void send_read_page(struct mxc_nand_host *host, uint8_t buf_id, {MTDDEBUG (MTD_DEBUG_LEVEL3 ,"send_read_page (%d)\n" , spare_only); -writew (buf_id, &host->regs->buf_addr); +writenfc (buf_id, &host->regs->buf_addr);/* Configure spare or page+spare access */ if (!host->pagesize_2k) { -uint32_t config1 =readw (&host->regs->config1); +uint32_t config1 =readnfc (&host->regs->config1);if (spare_only) - config1 |=NFC_SP_EN ; + config1 |=NFC_CONFIG1_SP_EN ;else - config1 &= ~NFC_SP_EN ; -writew (config1, &host->regs->config1); + config1 &= ~NFC_CONFIG1_SP_EN ; +writenfc (config1, &host->regs->config1); } -writew (NFC_OUTPUT , &host->regs->config2); +writenfc (NFC_OUTPUT , &host->regs->operation);/* Wait for operation to complete */ wait_op_done (host,TROP_US_DELAY , spare_only);
@@ -296,14 +296,14 @@ static void send_read_id(struct mxc_nand_host *host)uint16_t tmp;/* NANDFC buffer 0 is used for device ID output */ -writew (0x0 , &host->regs->buf_addr); +writenfc (0x0 , &host->regs->buf_addr);/* Read ID into main buffer */ - tmp =readw (&host->regs->config1); - tmp &= ~NFC_SP_EN ; -writew (tmp, &host->regs->config1); + tmp =readnfc (&host->regs->config1); + tmp &= ~NFC_CONFIG1_SP_EN ; +writenfc (tmp, &host->regs->config1); -writew (NFC_ID , &host->regs->config2); +writenfc (NFC_ID , &host->regs->operation);/* Wait for operation to complete */ wait_op_done (host,TROP_US_DELAY ,0 );
@@ -323,14 +323,14 @@ static uint16_t get_dev_status(struct mxc_nand_host *host)/* store the main area1 first word, later do recovery */ store =readl (main_buf);/* NANDFC buffer 1 is used for device status */ -writew (1 , &host->regs->buf_addr); +writenfc (1 , &host->regs->buf_addr);/* Read status into main buffer */ - tmp =readw (&host->regs->config1); - tmp &= ~NFC_SP_EN ; -writew (tmp, &host->regs->config1); + tmp =readnfc (&host->regs->config1); + tmp &= ~NFC_CONFIG1_SP_EN ; +writenfc (tmp, &host->regs->config1); -writew (NFC_STATUS , &host->regs->config2); +writenfc (NFC_STATUS , &host->regs->operation);/* Wait for operation to complete */ wait_op_done (host,TROP_US_DELAY ,0 );
@@ -359,13 +359,13 @@ static void _mxc_nand_enable_hwecc(struct mtd_info *mtd, int on) {struct nand_chip *nand_chip = mtd->priv;struct mxc_nand_host *host = nand_chip->priv; -uint16_t tmp =readw (&host->regs->config1); +uint16_t tmp =readnfc (&host->regs->config1);if (on) - tmp |=NFC_ECC_EN ; + tmp |=NFC_V1_V2_CONFIG1_ECC_EN ;else - tmp &= ~NFC_ECC_EN ; -writew (tmp, &host->regs->config1); + tmp &= ~NFC_V1_V2_CONFIG1_ECC_EN ; +writenfc (tmp, &host->regs->config1); }#ifdef CONFIG_MXC_NAND_HWECC
@@ -698,7 +698,7 @@ static int mxc_nand_correct_data(struct mtd_info *mtd, u_char *dat,* additional correction. 2-Bit errors cannot be corrected by * HW ECC, so we need to return failure */ -uint16_t ecc_status =readw (&host->regs->ecc_status_result); +uint16_t ecc_status =readnfc (&host->regs->ecc_status_result);if (((ecc_status &0x3 ) ==2 ) || ((ecc_status >>2 ) ==2 )) { MTDDEBUG(MTD_DEBUG_LEVEL0,
@@ -1241,24 +1241,24 @@ int board_nand_init(struct nand_chip *this)#endif #ifdef MXC_NFC_V2_1 - tmp =readw (&host->regs->config1); - tmp |=NFC_ONE_CYCLE ; - tmp |=NFC_4_8N_ECC ; -writew (tmp, &host->regs->config1); + tmp =readnfc (&host->regs->config1); + tmp |=NFC_V2_CONFIG1_ONE_CYCLE ; + tmp |=NFC_V2_CONFIG1_ECC_MODE_4 ; +writenfc (tmp, &host->regs->config1);if (host->pagesize_2k) -writew (64 /2 , &host->regs->spare_area_size); +writenfc (64 /2 , &host->regs->spare_area_size);else -writew (16 /2 , &host->regs->spare_area_size); +writenfc (16 /2 , &host->regs->spare_area_size);#endif /* * preset operation * Unlock the internal RAM Buffer */ -writew (0x2 , &host->regs->config); +writenfc (0x2 , &host->regs->config);/* Blocks to be unlocked */ -writew (0x0 , &host->regs->unlockstart_blkaddr); +writenfc (0x0 , &host->regs->unlockstart_blkaddr);/* Originally (Freescale LTIB 2.6.21) 0x4000 was written to the * unlockend_blkaddr, but the magic 0x4000 does not always work * when writing more than some 32 megabytes (on 2k page nands)
@@ -1270,10 +1270,10 @@ int board_nand_init(struct nand_chip *this)* This might be NAND chip specific and the i.MX31 datasheet is * extremely vague about the semantics of this register. */ -writew (0xFFFF , &host->regs->unlockend_blkaddr); +writenfc (0xFFFF , &host->regs->unlockend_blkaddr);/* Unlock Block Command for given address range */ -writew (0x4 , &host->regs->wrprot); +writenfc (0x4 , &host->regs->wrprot);return 0 ; }
include/fsl_nfc.h +26 -46
84 lines not on this page · raw message
nand_spl/nand_boot_fsl_nfc.c +25 -22
104 lines not on this page · raw message
Signature · 1 line
1.7.10.4
PATCH v5 2/8 nand: mxc: Add support for i.MX5
---
Changes in v5: None
Changes in v4: None
Changes in v3:
- Separate code reformatting from behavioral changes.
Changes in v2: None
arch/arm/include/asm/arch-mx5/imx-regs.h | 9 +++ drivers/mtd/nand/mxc_nand.c | 129 +++++++++++++++++++++++++++--- include/fsl_nfc.h | 79 +++++++++++++++++- nand_spl/nand_boot_fsl_nfc.c | 67 +++++++++++++++- 4 files changed, 269 insertions(+), 15 deletions(-)
arch/arm/include/asm/arch-mx5/imx-regs.h +9 -0
@@ -224,6 +224,15 @@#define CS0_32M_CS1_32M_CS2_32M_CS3_32M 3/* +* SRC register definitions +*/ +#if defined(CONFIG_MX51 ) +#define SRC_SBMR_NF16B (1 << 2) +#elif defined(CONFIG_MX53 ) +#define SRC_SBMR_NF16B (1 << 13) +#endif + +/* * CSPI register definitions */ #define MXC_ECSPI
drivers/mtd/nand/mxc_nand.c +118 -11
275 lines not on this page · raw message
include/fsl_nfc.h +77 -2
133 lines not on this page · raw message
nand_spl/nand_boot_fsl_nfc.c +65 -2
109 lines not on this page · raw message
Signature · 1 line
1.7.10.4
PATCH v5 3/8 imx: mx5: lowlevel_init: Simplify code
In reply to Benoît ThébaudeauDon't use several instructions to build constant values.
---
Changes in v5: None
Changes in v4: None
Changes in v3:
- New patch.
Changes in v2: None
arch/arm/cpu/armv7/mx5/lowlevel_init.S | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-)
arch/arm/cpu/armv7/mx5/lowlevel_init.S +2 -6
@@ -309,8 +309,7 @@ setup_pll_func: ldr r0, =CCM_BASE_ADDR ldr r1, =0x00015154 str r1, [r0, #CLKCTL_CBCMR] - ldr r1, =0x02888945 - orr r1, r1, #(1 << 16) + ldr r1, =0x02898945 str r1, [r0, #CLKCTL_CBCDR] /* make sure change is effective */ 1: ldr r1, [r0, #CLKCTL_CDHIPR]
@@ -321,10 +320,7 @@ setup_pll_func: /* Switch peripheral to PLL2 */ ldr r0, =CCM_BASE_ADDR - ldr r1, =0x00808145 - orr r1, r1, #(2 << 10) - orr r1, r1, #(0 << 16) - orr r1, r1, #(1 << 19) + ldr r1, =0x00888945 str r1, [r0, #CLKCTL_CBCDR] ldr r1, =0x00016154
Signature · 1 line
1.7.10.4
PATCH v5 4/8 imx: mx53ard: Add support for NAND Flash
In reply to Benoît ThébaudeauAdd support for the Samsung K9LAG08U0M NAND Flash (2-GiB MLC NAND Flash, 2-kiB pages, 256-kiB blocks, 30-ns R/W cycles, 1 CS) on mx53ard.
eNFC_CLK_ROOT is set up with a cycle time of 37.5 ns (400 MHz / 3 / 5) for this board, which satisfies the 30-ns NF R/W cycle requirement.
---
Changes in v5: None
Changes in v4: None
Changes in v3:
- New patch.
Changes in v2: None
board/freescale/mx53ard/mx53ard.c | 18 ++++++++++++++++++ include/configs/mx53ard.h | 10 ++++++++++ 2 files changed, 28 insertions(+)
board/freescale/mx53ard/mx53ard.c +18 -0
@@ -58,6 +58,23 @@ void dram_init_banksize(void) gd->bd->bi_dram[1 ].size =PHYS_SDRAM_2_SIZE ; } +#ifdef CONFIG_NAND_MXC +static void setup_iomux_nand (void ) +{ +mxc_request_iomux (MX53_PIN_NANDF_CLE ,IOMUX_CONFIG_ALT0 ); +mxc_request_iomux (MX53_PIN_NANDF_ALE ,IOMUX_CONFIG_ALT0 ); +mxc_request_iomux (MX53_PIN_NANDF_CS0 ,IOMUX_CONFIG_ALT0 ); +mxc_request_iomux (MX53_PIN_NANDF_RE_B ,IOMUX_CONFIG_ALT0 ); +mxc_request_iomux (MX53_PIN_NANDF_WE_B ,IOMUX_CONFIG_ALT0 ); +mxc_request_iomux (MX53_PIN_NANDF_WP_B ,IOMUX_CONFIG_ALT0 ); +mxc_request_iomux (MX53_PIN_NANDF_RB0 ,IOMUX_CONFIG_ALT0 ); +} +#else +static void setup_iomux_nand (void ) +{ +} +#endif +static void setup_iomux_uart (void ) {/* UART1 RXD */
@@ -277,6 +294,7 @@ static void weim_cs1_settings(void)int board_early_init_f (void ) { +setup_iomux_nand ();setup_iomux_uart ();return 0 ; }
include/configs/mx53ard.h +10 -0
@@ -41,6 +41,16 @@#define CONFIG_BOARD_EARLY_INIT_F #define CONFIG_MXC_GPIO +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE NFC_BASE_ADDR_AXI +#define CONFIG_NAND_MXC +#define CONFIG_MXC_NAND_REGS_BASE NFC_BASE_ADDR_AXI +#define CONFIG_MXC_NAND_IP_REGS_BASE NFC_BASE_ADDR +#define CONFIG_SYS_NAND_LARGEPAGE +#define CONFIG_MXC_NAND_HWECC +#define CONFIG_SYS_NAND_USE_FLASH_BBT +#define CONFIG_CMD_NAND +#define CONFIG_MXC_UART #define CONFIG_MXC_UART_BASE UART1_BASE
Signature · 1 line
1.7.10.4
PATCH v5 5/8 nand: mxc: Fix debug trace in mxc_nand_read_oob_syndrome()
In reply to Benoît ThébaudeauThe page number indicated in the debug trace of mxc_nand_read_oob_syndrome() did not match the page being worked on.
By the way, replace the GCC-specific __FUNCTION__ with __func__.
---
Changes in v5:
- Replace __FUNCTION__ with __func__.
Changes in v4:
- New patch.
Changes in v3: None
Changes in v2: None
drivers/mtd/nand/mxc_nand.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mtd/nand/mxc_nand.c +1 -1
@@ -450,7 +450,7 @@ static int mxc_nand_read_oob_syndrome(struct mtd_info *mtd,MTDDEBUG (MTD_DEBUG_LEVEL0 ,"%s: Reading OOB area of page %u to oob %p\n" , - __FUNCTION__, host->page_addr, buf); + __func__, page, buf); chip->cmdfunc (mtd,NAND_CMD_READOOB , mtd->writesize, page);for (i =0 ; i < chip->ecc.steps; i++) {
Signature · 1 line
1.7.10.4
PATCH v5 6/8 nand: mxc: Use appropriate page number in syndrome functions
In reply to Benoît ThébaudeauThe syndrome functions should use the page number passed as argument instead of the page number saved upon NAND_CMD_READ0.
This does not make any difference if the NAND_NO_AUTOINCR option is set, but otherwise this fixes accesses to the wrong pages.
---
Changes in v5: None
Changes in v4:
- New patch.
Changes in v3: None
Changes in v2: None
drivers/mtd/nand/mxc_nand.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/mtd/nand/mxc_nand.c +3 -3
@@ -504,7 +504,7 @@ static int mxc_nand_read_page_raw_syndrome(struct mtd_info *mtd,int n;_mxc_nand_enable_hwecc (mtd,0 ); - chip->cmdfunc (mtd,NAND_CMD_READ0 ,0x00 , host->page_addr); + chip->cmdfunc (mtd,NAND_CMD_READ0 ,0x00 , page);for (n =0 , steps = chip->ecc.steps; steps >0 ; n++, steps--) { host->col_addr = n * eccsize;
@@ -548,7 +548,7 @@ static int mxc_nand_read_page_syndrome(struct mtd_info *mtd,uint8_t *oob = chip->oob_poi;MTDDEBUG (MTD_DEBUG_LEVEL1 ,"Reading page %u to buf %p oob %p\n" , - host->page_addr, buf, oob); + page, buf, oob);/* first read the data area and the available portion of OOB */ for (n =0 ; eccsteps; n++, eccsteps--, p += eccsize) {
@@ -586,7 +586,7 @@ static int mxc_nand_read_page_syndrome(struct mtd_info *mtd,/* Then switch ECC off and read the OOB area to get the ECC code */ _mxc_nand_enable_hwecc (mtd,0 ); - chip->cmdfunc (mtd,NAND_CMD_READOOB , mtd->writesize, host->page_addr); + chip->cmdfunc (mtd,NAND_CMD_READOOB , mtd->writesize, page); eccsteps = chip->ecc.steps; oob = chip->oob_poi + chip->ecc.prepad;for (n =0 ; eccsteps; n++, eccsteps--, p += eccsize) {
Signature · 1 line
1.7.10.4
PATCH v5 7/8 Makefile: u-boot-with-spl.bin: Pad to CONFIG_SPL_MAX_SIZE
In reply to Benoît ThébaudeauPAD_TO is not a generic SPL configuration option, so use CONFIG_SPL_MAX_SIZE instead.
---
Changes in v5: None
Changes in v4:
- New patch.
Changes in v3: None
Changes in v2: None
Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
Makefile +1 -1
@@ -486,7 +486,7 @@ $(obj)u-boot.dis: $(obj)u-boot $(OBJDUMP) -d $< > $@ $(obj)u-boot-with-spl.bin: $(obj)spl/u-boot-spl.bin $(obj)u-boot.bin - $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $(obj)spl/u-boot-spl $(obj)spl/u-boot-spl-pad.bin + $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(CONFIG_SPL_MAX_SIZE) -O binary $(obj)spl/u-boot-spl $(obj)spl/u-boot-spl-pad.bin cat $(obj)spl/u-boot-spl-pad.bin $(obj)u-boot.bin > $@ rm $(obj)spl/u-boot-spl-pad.bin
Signature · 1 line
1.7.10.4
PATCH v5 8/8 nand: mxc: Switch NAND SPL to generic SPL
In reply to Benoît Thébaudeau---
Changes in v5:
- Remove spaces between function name and open parenthesis.
- Fix mx31pdk and tx25 Makefile-s and SPL linker scripts.
- Remove the useless definition of CONFIG_SPL_LDSCRIPT.
- Fix the call to nand_boot().
Changes in v4:
- New patch.
Changes in v3: None
Changes in v2: None
Makefile | 3 + arch/arm/cpu/arm1136/config.mk | 3 - arch/arm/cpu/arm1136/start.S | 2 - arch/arm/cpu/arm926ejs/start.S | 9 +- board/freescale/mx31pdk/Makefile | 4 + board/freescale/mx31pdk/config.mk | 5 -- .../freescale/mx31pdk/u-boot-spl.lds | 20 +++-- board/karo/tx25/Makefile | 5 +- board/karo/tx25/config.mk | 5 -- .../u-boot.lds => board/karo/tx25/u-boot-spl.lds | 16 ++-- boards.cfg | 2 +- drivers/mtd/nand/Makefile | 1 + drivers/mtd/nand/mxc_nand.c | 10 +-- include/fsl_nfc.h => drivers/mtd/nand/mxc_nand.h | 10 +-- .../mtd/nand/mxc_nand_spl.c | 26 +++--- include/common.h | 6 +- include/configs/mx31pdk.h | 10 ++- include/configs/tx25.h | 13 ++- include/configs/woodburn_sd.h | 1 + nand_spl/board/freescale/mx31pdk/Makefile | 68 --------------- nand_spl/board/karo/tx25/Makefile | 89 -------------------- nand_spl/board/karo/tx25/config.mk | 1 - 22 files changed, 87 insertions(+), 222 deletions(-) delete mode 100644 board/freescale/mx31pdk/config.mk rename nand_spl/board/karo/tx25/u-boot.lds => board/freescale/mx31pdk/u-boot-spl.lds (86%) delete mode 100644 board/karo/tx25/config.mk rename nand_spl/board/freescale/mx31pdk/u-boot.lds => board/karo/tx25/u-boot-spl.lds (89%) rename include/fsl_nfc.h => drivers/mtd/nand/mxc_nand.h (98%) rename nand_spl/nand_boot_fsl_nfc.c => drivers/mtd/nand/mxc_nand_spl.c (92%) delete mode 100644 nand_spl/board/freescale/mx31pdk/Makefile delete mode 100644 nand_spl/board/karo/tx25/Makefile delete mode 100644 nand_spl/board/karo/tx25/config.mk
Makefile +3 -0
@@ -470,6 +470,9 @@ $(obj)u-boot.img: $(obj)u-boot.bin $(OBJTREE)/u-boot.imx : $(obj)u-boot.bin $(SUBDIR_TOOLS) depend $(MAKE) -C $(SRCTREE)/arch/arm/imx-common $@ +$(OBJTREE)/SPL : $(obj)spl/u-boot-spl.bin depend + $(MAKE) -C $(SRCTREE)/arch/arm/imx-common $@ + $(obj)u-boot.kwb: $(obj)u-boot.bin $(obj)tools/mkimage -n $(CONFIG_SYS_KWD_CONFIG) -T kwbimage \ -a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_TEXT_BASE) -d $< $@
arch/arm/cpu/arm1136/config.mk +0 -3
@@ -31,6 +31,3 @@ PLATFORM_CPPFLAGS += -march=armv5 # ========================================================================= PF_RELFLAGS_SLB_AT := $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) PLATFORM_RELFLAGS += $(PF_RELFLAGS_SLB_AT) -ifdef CONFIG_SPL_BUILD -ALL-y += $(OBJTREE)/SPL -endif
arch/arm/cpu/arm1136/start.S +0 -2
@@ -235,8 +235,6 @@ fixnext: add r2, r2, #8 /* each rel.dyn entry is 8 bytes */ cmp r2, r3 blo fixloop - bx lr - #endif relocate_done:
arch/arm/cpu/arm926ejs/start.S +7 -2
@@ -140,6 +140,10 @@ _TEXT_BASE: _bss_start_ofs: .word __bss_start - _start +.global _image_copy_end_ofs +_image_copy_end_ofs: + .word __image_copy_end - _start + .globl _bss_end_ofs _bss_end_ofs: .word __bss_end__ - _start
@@ -196,7 +200,6 @@ reset: /*------------------------------------------------------------------------------*/ -#if !defined(CONFIG_SPL_BUILD) || defined(CONFIG_NAND_SPL) /* * void relocate_code (addr_sp, gd, addr_moni) *
@@ -216,7 +219,7 @@ relocate_code: moveq r9, #0 /* no relocation. offset(r9) = 0 */ beq relocate_done /* skip relocation */ mov r1, r6 /* r1 <- scratch for copy loop */ - ldr r3, _bss_start_ofs + ldr r3, _image_copy_end_ofs add r2, r0, r3 /* r2 <- source end address */ copy_loop:
@@ -270,6 +273,8 @@ relocate_done: bx lr +#ifndef CONFIG_SPL_BUILD + _rel_dyn_start_ofs: .word __rel_dyn_start - _start _rel_dyn_end_ofs:
board/freescale/mx31pdk/Makefile +4 -0
@@ -27,7 +27,11 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o +ifdef CONFIG_SPL_BUILD +SOBJS := lowlevel_init.o +else COBJS := mx31pdk.o +endif SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS))
board/freescale/mx31pdk/config.mk deleted +0 -5
@@ -1,5 +0,0 @@ -ifdef CONFIG_NAND_SPL -CONFIG_SYS_TEXT_BASE = 0x87ec0000 -else -CONFIG_SYS_TEXT_BASE = 0x87f00000 -endif
board/freescale/mx31pdk/u-boot-spl.lds renamed from nand_spl/board/karo/tx25/u-boot.lds +11 -9
@@ -30,30 +30,32 @@ SECTIONS . = ALIGN(4); .text : { - start.o (.text) - lowlevel_init.o (.text) - nand_boot_fsl_nfc.o (.text) - *(.text) + arch/arm/cpu/arm1136/start.o (.text*) + board/freescale/mx31pdk/libmx31pdk.o (.text*) + drivers/mtd/nand/libnand.o (.text*) + *(.text*) . = 2K; } . = ALIGN(4); - .rodata : { *(.rodata) } + .rodata : { *(.rodata*) } . = ALIGN(4); .data : { - *(.data) + *(.data*) } . = ALIGN(4); . = ALIGN(4); .u_boot_list : { - #include <u-boot.lst> + #include <u-boot.lst> } . = ALIGN(4); + __image_copy_end = .; + .rel.dyn : { __rel_dyn_start = .; *(.rel*)
@@ -62,14 +64,14 @@ SECTIONS .dynsym : { __dynsym_start = .; - *(.dynsym) + *(.dynsym*) } _end = .; .bss __rel_dyn_start (OVERLAY) : { __bss_start = .; - *(.bss) + *(.bss*) . = ALIGN(4); __bss_end__ = .; }
board/karo/tx25/Makefile +4 -1
@@ -25,8 +25,11 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o -COBJS := tx25.o +ifdef CONFIG_SPL_BUILD SOBJS := lowlevel_init.o +else +COBJS := tx25.o +endif SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS))
board/karo/tx25/config.mk deleted +0 -5
@@ -1,5 +0,0 @@ -ifdef CONFIG_NAND_SPL -CONFIG_SYS_TEXT_BASE = 0x810c0000 -else -CONFIG_SYS_TEXT_BASE = 0x81200000 -endif
board/karo/tx25/u-boot-spl.lds renamed from nand_spl/board/freescale/mx31pdk/u-boot.lds +8 -8
@@ -30,19 +30,19 @@ SECTIONS . = ALIGN(4); .text : { - start.o (.text) - lowlevel_init.o (.text) - nand_boot_fsl_nfc.o (.text) - *(.text) + arch/arm/cpu/arm926ejs/start.o (.text*) + board/karo/tx25/libtx25.o (.text*) + drivers/mtd/nand/libnand.o (.text*) + *(.text*) . = 2K; } . = ALIGN(4); - .rodata : { *(.rodata) } + .rodata : { *(.rodata*) } . = ALIGN(4); .data : { - *(.data) + *(.data*) } . = ALIGN(4);
@@ -64,14 +64,14 @@ SECTIONS .dynsym : { __dynsym_start = .; - *(.dynsym) + *(.dynsym*) } _end = .; .bss __rel_dyn_start (OVERLAY) : { __bss_start = .; - *(.bss) + *(.bss*) . = ALIGN(4); __bss_end__ = .; }
boards.cfg +1 -1
@@ -45,7 +45,7 @@ imx31_phycore arm arm1136 - - imx31_phycore_eet arm arm1136 imx31_phycore - mx31 imx31_phycore:IMX31_PHYCORE_EET qong arm arm1136 - davedenx mx31 mx31ads arm arm1136 - freescale mx31 -mx31pdk arm arm1136 - freescale mx31 mx31pdk:NAND_U_BOOT +mx31pdk arm arm1136 - freescale mx31 tt01 arm arm1136 - hale mx31 imx31_litekit arm arm1136 - logicpd mx31 flea3 arm arm1136 - CarMediaLab mx35
drivers/mtd/nand/Makefile +1 -0
@@ -82,6 +82,7 @@ COBJS-$(CONFIG_NAND_PLAT) += nand_plat.o else # minimal SPL drivers COBJS-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_spl.o +COBJS-$(CONFIG_NAND_MXC) += mxc_nand_spl.o endif # drivers endif # nand
drivers/mtd/nand/mxc_nand.c +5 -5
@@ -26,7 +26,7 @@ defined(CONFIG_MX51) || defined(CONFIG_MX53)#include <asm/arch/imx-regs.h> #endif -#include <fsl_nfc.h> +#include "mxc_nand.h" #define DRIVER_NAME "mxc_nand"
@@ -36,9 +36,9 @@ struct mxc_nand_host {struct mtd_info mtd;struct nand_chip *nand; -struct fsl_nfc_regs __iomem *regs; +struct mxc_nand_regs __iomem *regs;#ifdef MXC_NFC_V3_2 -struct fsl_nfc_ip_regs __iomem *ip_regs; +struct mxc_nand_ip_regs __iomem *ip_regs;#endif int spare_only;int status_request;
@@ -1254,10 +1254,10 @@ int board_nand_init(struct nand_chip *this) this->read_buf = mxc_nand_read_buf; this->verify_buf = mxc_nand_verify_buf; - host->regs = (struct fsl_nfc_regs __iomem *)CONFIG_MXC_NAND_REGS_BASE ; + host->regs = (struct mxc_nand_regs __iomem *)CONFIG_MXC_NAND_REGS_BASE ;#ifdef MXC_NFC_V3_2 host->ip_regs = - (struct fsl_nfc_ip_regs __iomem *)CONFIG_MXC_NAND_IP_REGS_BASE ; + (struct mxc_nand_ip_regs __iomem *)CONFIG_MXC_NAND_IP_REGS_BASE ;#endif host->clk_act =1 ;
drivers/mtd/nand/mxc_nand.h renamed from include/fsl_nfc.h +5 -5
@@ -20,8 +20,8 @@* MA 02111-1307 USA */ -#ifndef __FSL_NFC_H -#define __FSL_NFC_H +#ifndef __MXC_NAND_H +#define __MXC_NAND_H/* * Register map and bit definitions for the Freescale NAND Flash Controller
@@ -73,7 +73,7 @@#define NAND_MXC_REG_OFFSET 0x1e00#endif -struct fsl_nfc_regs { +struct mxc_nand_regs {u8 main_area[NAND_MXC_NR_BUFS ][0x200 ];u8 spare_area[NAND_MXC_NR_BUFS ][NAND_MXC_SPARE_BUF_SIZE ];/*
@@ -131,7 +131,7 @@ struct fsl_nfc_regs { }; #ifdef MXC_NFC_V3_2 -struct fsl_nfc_ip_regs { +struct mxc_nand_ip_regs { u32 wrprot; u32 wrprot_unlock_blkaddr[8]; u32 config2;
@@ -222,4 +222,4 @@ struct fsl_nfc_ip_regs {#define writenfc writel#endif -#endif /* __FSL_NFC_H */ +#endif /* __MXC_NAND_H */
drivers/mtd/nand/mxc_nand_spl.c renamed from nand_spl/nand_boot_fsl_nfc.c +14 -12
@@ -28,13 +28,13 @@#include <nand.h> #include <asm/arch/imx-regs.h> #include <asm/io.h> -#include <fsl_nfc.h> +#include "mxc_nand.h" #if defined(MXC_NFC_V1 ) || defined(MXC_NFC_V2_1 ) -static struct fsl_nfc_regs *const nfc = (void *)NFC_BASE_ADDR ; +static struct mxc_nand_regs *const nfc = (void *)NFC_BASE_ADDR ;#elif defined(MXC_NFC_V3_2 ) -static struct fsl_nfc_regs *const nfc = (void *)NFC_BASE_ADDR_AXI ; -static struct fsl_nfc_ip_regs *const nfc_ip = (void *)NFC_BASE_ADDR ; +static struct mxc_nand_regs *const nfc = (void *)NFC_BASE_ADDR_AXI ; +static struct mxc_nand_ip_regs *const nfc_ip = (void *)NFC_BASE_ADDR ;#endif static void nfc_wait_ready (void )
@@ -68,7 +68,7 @@ static void nfc_nand_init(void) tmp = (readnfc (&nfc_ip->config2) & ~(NFC_V3_CONFIG2_SPAS_MASK |NFC_V3_CONFIG2_EDC_MASK |NFC_V3_CONFIG2_PS_MASK )) | -NFC_V3_CONFIG2_SPAS (CONFIG_SYS_NAND_SPARE_SIZE /2 ) | +NFC_V3_CONFIG2_SPAS (CONFIG_SYS_NAND_OOBSIZE /2 ) |NFC_V3_CONFIG2_INT_MSK |NFC_V3_CONFIG2_ECC_EN |NFC_V3_CONFIG2_ONE_CYCLE ;if (CONFIG_SYS_NAND_PAGE_SIZE ==4096 )
@@ -81,7 +81,7 @@ static void nfc_nand_init(void)* if spare size is larger that 16 bytes per 512 byte hunk * then use 8 symbol correction instead of 4 */ -if (CONFIG_SYS_NAND_SPARE_SIZE / ecc_per_page >16 ) +if (CONFIG_SYS_NAND_OOBSIZE / ecc_per_page >16 ) tmp |=NFC_V3_CONFIG2_ECC_MODE_8 ;else tmp &= ~NFC_V3_CONFIG2_ECC_MODE_8 ;
@@ -102,7 +102,7 @@ static void nfc_nand_init(void)int ecc_per_page =CONFIG_SYS_NAND_PAGE_SIZE /512 ;int config1; -writenfc (CONFIG_SYS_NAND_SPARE_SIZE /2 , &nfc->spare_area_size); +writenfc (CONFIG_SYS_NAND_OOBSIZE /2 , &nfc->spare_area_size);/* unlocking RAM Buff */ writenfc (0x2 , &nfc->config);
@@ -115,7 +115,7 @@ static void nfc_nand_init(void)* if spare size is larger that 16 bytes per 512 byte hunk * then use 8 symbol correction instead of 4 */ -if (CONFIG_SYS_NAND_SPARE_SIZE / ecc_per_page >16 ) +if (CONFIG_SYS_NAND_OOBSIZE / ecc_per_page >16 ) config1 &= ~NFC_V2_CONFIG1_ECC_MODE_4 ;else config1 |=NFC_V2_CONFIG1_ECC_MODE_4 ;
@@ -204,7 +204,7 @@ static int nfc_nand_check_ecc(void) #elif defined(MXC_NFC_V2_1) || defined(MXC_NFC_V3_2) u32 ecc_status = readl(&nfc->ecc_status_result); int ecc_per_page = CONFIG_SYS_NAND_PAGE_SIZE / 512; - int err_limit = CONFIG_SYS_NAND_SPARE_SIZE / ecc_per_page > 16 ? 8 : 4; + int err_limit = CONFIG_SYS_NAND_OOBSIZE / ecc_per_page > 16 ? 8 : 4; int subpages = CONFIG_SYS_NAND_PAGE_SIZE / 512; do {
@@ -333,10 +333,12 @@ static int nand_load(unsigned int from, unsigned int size, unsigned char *buf) }#if defined(CONFIG_ARM ) -void board_init_f (ulong bootflag) +void board_init_f (ulong bootflag) { -relocate_code (CONFIG_SYS_TEXT_BASE -TOTAL_MALLOC_LEN ,NULL , -CONFIG_SYS_TEXT_BASE ); +relocate_code (CONFIG_SPL_TEXT_BASE -TOTAL_MALLOC_LEN ,NULL , +CONFIG_SPL_TEXT_BASE ); + + asmvolatile ("ldr pc, =nand_boot\n" ); }#endif
include/common.h +5 -1
@@ -515,7 +515,11 @@ int dcache_status (void);void dcache_enable (void );void dcache_disable (void );void mmu_disable (void ); -void relocate_code (ulong ,gd_t *,ulong ) __attribute__ ((noreturn)); +void relocate_code (ulong, gd_t *, ulong) +#if !defined(CONFIG_ARM ) +__attribute__ ((noreturn)) +#endif +;ulong get_endaddr (void );void trap_init (ulong ); #if defined (CONFIG_4xx) || \
include/configs/mx31pdk.h +9 -1
@@ -45,7 +45,15 @@#define CONFIG_MACH_TYPE MACH_TYPE_MX31_3DS -#if defined(CONFIG_NAND_U_BOOT ) && !defined(CONFIG_NAND_SPL ) +#define CONFIG_SPL +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SPL_MAX_SIZE 2048 +#define CONFIG_SPL_NAND_SUPPORT + +#define CONFIG_SPL_TEXT_BASE 0x87ec0000 +#define CONFIG_SYS_TEXT_BASE 0x87f00000 + +#ifndef CONFIG_SPL_BUILD #define CONFIG_SKIP_LOWLEVEL_INIT #endif
include/configs/tx25.h +9 -4
@@ -31,8 +31,13 @@#define CONFIG_SYS_MONITOR_LEN (256 << 10)/* 256 kB for U-Boot */ -/* NAND BOOT is the only boot method */ -#define CONFIG_NAND_U_BOOT +#define CONFIG_SPL +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SPL_MAX_SIZE 2048 +#define CONFIG_SPL_NAND_SUPPORT + +#define CONFIG_SPL_TEXT_BASE 0x810c0000 +#define CONFIG_SYS_TEXT_BASE 0x81200000#ifndef MACH_TYPE_TX25 #define MACH_TYPE_TX25 2177
@@ -40,7 +45,7 @@#define CONFIG_MACH_TYPE MACH_TYPE_TX25 -#ifdef CONFIG_NAND_SPL +#ifdef CONFIG_SPL_BUILD /* Start copying real U-boot from the second page */ #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x800#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x30000
@@ -49,7 +54,7 @@#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST#define CONFIG_SYS_NAND_PAGE_SIZE 2048 -#define CONFIG_SYS_NAND_SPARE_SIZE 64 +#define CONFIG_SYS_NAND_OOBSIZE 64#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)#define CONFIG_SYS_NAND_PAGE_COUNT 64#define CONFIG_SYS_NAND_SIZE (128 * 1024 * 1024)
include/configs/woodburn_sd.h +1 -0
@@ -38,6 +38,7 @@#define CONFIG_SPL #define CONFIG_SPL_FRAMEWORK #define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm1136/u-boot-spl.lds" +#define CONFIG_SPL_TARGET "SPL"#define CONFIG_SPL_LIBCOMMON_SUPPORT #define CONFIG_SPL_LIBGENERIC_SUPPORT #define CONFIG_SPL_LIBDISK_SUPPORT
nand_spl/board/freescale/mx31pdk/Makefile deleted +0 -68
68 lines not on this page · raw message
nand_spl/board/karo/tx25/Makefile deleted +0 -89
89 lines not on this page · raw message
nand_spl/board/karo/tx25/config.mk deleted +0 -1
@@ -1 +0,0 @@ -PAD_TO := 2048
Signature · 1 line
1.7.10.4
PATCH v5 8/8 nand: mxc: Switch NAND SPL to generic SPL
Quoted 10 lines · Beno?t Th?baudeau
Subject: [PATCH v5 8/8] nand: mxc: Switch NAND SPL to generic SPL
Signed-off-by Beno?t Th?baudeau <[email protected]>---
Changes in v5:
- Remove spaces between function name and open parenthesis.
- Fix mx31pdk and tx25 Makefile-s and SPL linker scripts.
- Remove the useless definition ofCONFIG_SPL_LDSCRIPT.
- Fix the call tonand_boot().
Quoted 5 lines
Changes in v4:
- New patch.Changes in v3: None
Changes in v2: None
This is now supposed to be working and compile-tested.
Custodians, please review and advise.
Board maintainers, please test.
Tell me if I should split away some stuff.
Should doc/README.arm-relocation be updated, and how since tx25 no longer uses NAND SPL, which is also deprecated?
Note that mx31pdk and tx25 had been broken by commit e05e5de7fae5bec79617e113916dac6631251156. After this commit, for those boards, _main called board_init_f, which called relocate_code, which unexpectedly (for their users) returned to nowhere in ctr0.S instead of calling nand_boot. Also, crt0.S calls nand_boot if CONFIG_SPL_BUILD is not defined but CONFIG_NAND_SPL is, which is not normal for NAND SPL. Other NAND SPL boards may be broken too, but that's not too much of an issue since they are supposed to migrate to generic SPL.
Best regards,
Beno?t
PATCH v5 8/8 nand: mxc: Switch NAND SPL to generic SPL
Quoted 29 lines · Beno?t Th?baudeau
Quoted 10 lines · Beno?t Th?baudeau
Subject: [PATCH v5 8/8] nand: mxc: Switch NAND SPL to generic SPL
Signed-off-by Beno?t Th?baudeau <[email protected]>---
Changes in v5:
- Remove spaces between function name and open parenthesis.
- Fix mx31pdk and tx25 Makefile-s and SPL linker scripts.
- Remove the useless definition ofCONFIG_SPL_LDSCRIPT.
- Fix the call tonand_boot().Quoted 5 lines
Changes in v4:
- New patch.Changes in v3: None
Changes in v2: NoneThis is now supposed to be working and compile-tested.
Custodians, please review and advise.
Board maintainers, please test.
Tell me if I should split away some stuff.
Should doc/README.arm-relocation be updated, and how since tx25 no longer uses
NAND SPL, which is also deprecated?
Quoted 12 lines
Note that mx31pdk and tx25 had been broken by commit
e05e5de7fae5bec79617e113916dac6631251156. After this commit, for those boards,_maincalledboard_init_f, which calledrelocate_code, which unexpectedly (for
their users) returned to nowhere inctr0.Sinstead of callingnand_boot. Also,crt0.Scallsnand_bootifCONFIG_SPL_BUILDis not defined butCONFIG_NAND_SPLis, which is not normal for NAND SPL. Other NAND SPL boards may be broken too,
but that's not too much of an issue since they are supposed to migrate to generic SPL.
I am also wondering if board_init_f should not be moved out of mxc_nand_spl.c to either <board>/lowlevel_init.S or <board>/<board>.c. That would make mxc_nand_spl.c more generic if for some reason a board needs to do specific things. Any opinion?
For the start.S files, since it's not possible to know from CONFIG_SPL_BUILD and CONFIG_NAND_SPL if relocate_code is needed or not, I see the following choices:
1) Let it defined in all cases. It's quite small, so it won't hurt much.
2) Create a specific SPL #define (e.g. CONFIG_SPL_RELOCATE_CODE) to define it for generic SPL only if needed.
3) Just create a specific linker section for it so that it's automatically garbage-collected if unneeded.
Any opinion?
Best regards,
Beno?t
PATCH v5 8/8 nand: mxc: Switch NAND SPL to generic SPL
Quoted 50 lines · Beno?t Th?baudeau
Quoted 29 lines · Beno?t Th?baudeau
Quoted 10 lines · Beno?t Th?baudeau
Subject: [PATCH v5 8/8] nand: mxc: Switch NAND SPL to generic SPL
Signed-off-by Beno?t Th?baudeau <[email protected]>---
Changes in v5:
- Remove spaces between function name and open parenthesis.
- Fix mx31pdk and tx25 Makefile-s and SPL linker scripts.
- Remove the useless definition ofCONFIG_SPL_LDSCRIPT.
- Fix the call tonand_boot().Quoted 5 lines
Changes in v4:
- New patch.Changes in v3: None
Changes in v2: NoneThis is now supposed to be working and compile-tested.
Custodians, please review and advise.
Board maintainers, please test.
Tell me if I should split away some stuff.
Should doc/README.arm-relocation be updated, and how since tx25 no longer uses
NAND SPL, which is also deprecated?Quoted 13 lines
Note that mx31pdk and tx25 had been broken by commit
e05e5de7fae5bec79617e113916dac6631251156. After this commit, for those boards,_maincalledboard_init_f, which calledrelocate_code, which unexpectedly (for
their users) returned to nowhere inctr0.Sinstead of callingnand_boot. Also,crt0.Scallsnand_bootifCONFIG_SPL_BUILDis not defined butCONFIG_NAND_SPL
is, which is not normal for NAND SPL. Other NAND SPL boards may be broken too,
but that's not too much of an issue since they are supposed to migrate to generic SPL.I am also wondering if
board_init_fshould not be moved out ofmxc_nand_spl.cto
either <board>/lowlevel_init.S or <board>/<board>.c. That would makemxc_nand_spl.cmore generic if for some reason a board needs to do specific things. Any opinion?
Quoted 10 lines
For the
start.Sfiles, since it's not possible to know fromCONFIG_SPL_BUILDandCONFIG_NAND_SPLifrelocate_codeis needed or not, I see the following choices:
1) Let it defined in all cases. It's quite small, so it won't hurt much.
2) Create a specific SPL #define (e.g.CONFIG_SPL_RELOCATE_CODE) to define it for generic SPL only if needed.
3) Just create a specific linker section for it so that it's automatically garbage-collected if unneeded.
Any opinion?
I'm also considering to factorize relocate_code to crt0.S. There's not really a good reason for it to be depending on each ARM processor. Any opinion?
Best regards,
Beno?t
PATCH v5 8/8 nand: mxc: Switch NAND SPL to generic SPL
Dear Beno?t Th?baudeau,
Quoted 60 lines · Beno?t Th?baudeau
Quoted 59 lines · Beno?t Th?baudeau
Quoted 30 lines · Beno?t Th?baudeau
Quoted 11 lines
Subject: [PATCH v5 8/8] nand: mxc: Switch NAND SPL to generic SPL
Signed-off-by Beno?t Th?baudeau <[email protected]>---
Changes in v5:
- Remove spaces between function name and open parenthesis.
- Fix mx31pdk and tx25 Makefile-s and SPL linker scripts.
- Remove the useless definition ofCONFIG_SPL_LDSCRIPT.
- Fix the call tonand_boot().Quoted 5 lines
Changes in v4:
- New patch.Changes in v3: None
Changes in v2: NoneThis is now supposed to be working and compile-tested.
Custodians, please review and advise.
Board maintainers, please test.
Tell me if I should split away some stuff.
Should doc/README.arm-relocation be updated, and how since tx25 no longer uses
NAND SPL, which is also deprecated?Quoted 13 lines
Note that mx31pdk and tx25 had been broken by commit
e05e5de7fae5bec79617e113916dac6631251156. After this commit, for those boards,_maincalledboard_init_f, which calledrelocate_code, which unexpectedly (for
their users) returned to nowhere inctr0.Sinstead of callingnand_boot. Also,crt0.Scallsnand_bootifCONFIG_SPL_BUILDis not defined butCONFIG_NAND_SPL
is, which is not normal for NAND SPL. Other NAND SPL boards may be broken too,
but that's not too much of an issue since they are supposed to migrate to generic SPL.I am also wondering if
board_init_fshould not be moved out ofmxc_nand_spl.cto
either <board>/lowlevel_init.S or <board>/<board>.c. That would makemxc_nand_spl.cmore generic if for some reason a board needs to do specific things. Any opinion?For the
start.Sfiles, since it's not possible to know fromCONFIG_SPL_BUILDandCONFIG_NAND_SPLifrelocate_codeis needed or not, I see the following choices:
1) Let it defined in all cases. It's quite small, so it won't hurt much.
2) Create a specific SPL #define (e.g.CONFIG_SPL_RELOCATE_CODE) to define it
Quoted 8 lines
Quoted 8 lines
for generic SPL only if needed.
3) Just create a specific linker section for it so that it's automatically
garbage-collected if unneeded.
Any opinion?
How much of start.S can be actually rewritten in pure-C ?
Best regards,
Marek Vasut
PATCH v5 8/8 nand: mxc: Switch NAND SPL to generic SPL
Dear Marek Vasut,
Quoted 64 lines · Marek Vasut
Dear Beno?t Th?baudeau,
Quoted 62 lines · Beno?t Th?baudeau
Quoted 61 lines · Beno?t Th?baudeau
Quoted 30 lines · Beno?t Th?baudeau
Quoted 11 lines
Subject: [PATCH v5 8/8] nand: mxc: Switch NAND SPL to generic SPL
Signed-off-by Beno?t Th?baudeau <[email protected]>---
Changes in v5:
- Remove spaces between function name and open parenthesis.
- Fix mx31pdk and tx25 Makefile-s and SPL linker scripts.
- Remove the useless definition ofCONFIG_SPL_LDSCRIPT.
- Fix the call tonand_boot().Quoted 5 lines
Changes in v4:
- New patch.Changes in v3: None
Changes in v2: NoneThis is now supposed to be working and compile-tested.
Custodians, please review and advise.
Board maintainers, please test.
Tell me if I should split away some stuff.
Should doc/README.arm-relocation be updated, and how since tx25 no longer uses
NAND SPL, which is also deprecated?Quoted 13 lines
Note that mx31pdk and tx25 had been broken by commit
e05e5de7fae5bec79617e113916dac6631251156. After this commit, for those boards,_maincalledboard_init_f, which calledrelocate_code, which unexpectedly (for
their users) returned to nowhere inctr0.Sinstead of callingnand_boot. Also,crt0.Scallsnand_bootifCONFIG_SPL_BUILDis not defined butCONFIG_NAND_SPL
is, which is not normal for NAND SPL. Other NAND SPL boards may be broken too,
but that's not too much of an issue since they are supposed to migrate to generic SPL.I am also wondering if
board_init_fshould not be moved out ofmxc_nand_spl.cto
either <board>/lowlevel_init.S or <board>/<board>.c. That would makemxc_nand_spl.cmore generic if for some reason a board needs to do specific things. Any opinion?For the
start.Sfiles, since it's not possible to know fromCONFIG_SPL_BUILDandCONFIG_NAND_SPLifrelocate_codeis needed or not, I see the following choices:
1) Let it defined in all cases. It's quite small, so it won't hurt much.
2) Create a specific SPL #define (e.g.CONFIG_SPL_RELOCATE_CODE) to define itfor generic SPL only if needed.
Quoted 8 lines
Quoted 6 lines
Quoted 6 lines
3) Just create a specific linker section for it so that it's automatically
garbage-collected if unneeded.
Any opinion?
How much of
start.Scan be actually rewritten in pure-C ?
I would say only relocate_code(). Apart from this function, start.S only deals with preprocessor register accesses and IRQ / exception handling that require assembly.
As to relocate_code(), it would still be tricky in pure C because it mixes absolute addresses with position-independent code and data accesses, so one would have to be very careful about the C coding of this function in order to avoid a dependency on compiler choices. Having it written in assembly guarantees a correct result and emphasizes the absolute/relative access constraints for easier maintenance.
But this is only my opinion.
Best regards,
Beno?t
PATCH v5 8/8 nand: mxc: Switch NAND SPL to generic SPL
Quoted 75 lines · Beno?t Th?baudeau
Dear Marek Vasut,
Quoted 72 lines · Marek Vasut
Dear Beno?t Th?baudeau,
Quoted 70 lines · Beno?t Th?baudeau
Quoted 69 lines · Beno?t Th?baudeau
Quoted 30 lines · Beno?t Th?baudeau
Quoted 11 lines
Subject: [PATCH v5 8/8] nand: mxc: Switch NAND SPL to generic SPL
Signed-off-by Beno?t Th?baudeau <[email protected]>---
Changes in v5:
- Remove spaces between function name and open parenthesis.
- Fix mx31pdk and tx25 Makefile-s and SPL linker scripts.
- Remove the useless definition ofCONFIG_SPL_LDSCRIPT.
- Fix the call tonand_boot().Quoted 5 lines
Changes in v4:
- New patch.Changes in v3: None
Changes in v2: NoneThis is now supposed to be working and compile-tested.
Custodians, please review and advise.
Board maintainers, please test.
Tell me if I should split away some stuff.
Should doc/README.arm-relocation be updated, and how since tx25 no longer uses
NAND SPL, which is also deprecated?Quoted 15 lines
Note that mx31pdk and tx25 had been broken by commit
e05e5de7fae5bec79617e113916dac6631251156. After this commit, for those
boards,_maincalledboard_init_f, which calledrelocate_code, which unexpectedly (for
their users) returned to nowhere inctr0.Sinstead of callingnand_boot. Also,crt0.Scallsnand_bootifCONFIG_SPL_BUILDis not defined butCONFIG_NAND_SPL
is, which is not normal for NAND SPL. Other NAND SPL boards may be broken too,
but that's not too much of an issue since they are supposed to migrate
to generic SPL.I am also wondering if
board_init_fshould not be moved out ofmxc_nand_spl.cto
either <board>/lowlevel_init.S or <board>/<board>.c. That would makemxc_nand_spl.cmore generic if for some reason a board needs to do specific things. Any opinion?For the
start.Sfiles, since it's not possible to know fromCONFIG_SPL_BUILDandCONFIG_NAND_SPLifrelocate_codeis needed or not, I see the following choices:
1) Let it defined in all cases. It's quite small, so it won't hurt much.
2) Create a specific SPL #define (e.g.CONFIG_SPL_RELOCATE_CODE) to define itfor generic SPL only if needed.
3) Just create a specific linker section for it so that it's automatically
garbage-collected if unneeded.
Quoted 8 lines
Quoted 3 lines
Quoted 1 line
Quoted 1 line
Any opinion?
How much of
start.Scan be actually rewritten in pure-C ?I would say only
relocate_code(). Apart from this function,start.Sonly deals
with preprocessor register accesses and IRQ / exception handling that require assembly.
s/preprocessor/coprocessor/
Quoted 13 lines
As to
relocate_code(), it would still be tricky in pure C because it mixes absolute addresses with position-independent code and data accesses, so one would have to be very careful about the C coding of this function in order to avoid a dependency on compiler choices. Having it written in assembly guarantees
a correct result and emphasizes the absolute/relative access constraints for easier maintenance.But this is only my opinion.
Best regards,
Beno?t
PATCH v5 8/8 nand: mxc: Switch NAND SPL to generic SPL
In reply to Benoît ThébaudeauHi Stefano,
Quoted 65 lines · Beno?t Th?baudeau
Quoted 51 lines · Beno?t Th?baudeau
Quoted 29 lines · Beno?t Th?baudeau
Quoted 10 lines · Beno?t Th?baudeau
Subject: [PATCH v5 8/8] nand: mxc: Switch NAND SPL to generic SPL
Signed-off-by Beno?t Th?baudeau <[email protected]>---
Changes in v5:
- Remove spaces between function name and open parenthesis.
- Fix mx31pdk and tx25 Makefile-s and SPL linker scripts.
- Remove the useless definition ofCONFIG_SPL_LDSCRIPT.
- Fix the call tonand_boot().Quoted 5 lines
Changes in v4:
- New patch.Changes in v3: None
Changes in v2: NoneThis is now supposed to be working and compile-tested.
Custodians, please review and advise.
Board maintainers, please test.
Tell me if I should split away some stuff.
Should doc/README.arm-relocation be updated, and how since tx25 no longer uses
NAND SPL, which is also deprecated?Quoted 13 lines
Note that mx31pdk and tx25 had been broken by commit
e05e5de7fae5bec79617e113916dac6631251156. After this commit, for those boards,_maincalledboard_init_f, which calledrelocate_code, which unexpectedly (for
their users) returned to nowhere inctr0.Sinstead of callingnand_boot. Also,crt0.Scallsnand_bootifCONFIG_SPL_BUILDis not defined butCONFIG_NAND_SPL
is, which is not normal for NAND SPL. Other NAND SPL boards may be broken too,
but that's not too much of an issue since they are supposed to migrate to generic SPL.I am also wondering if
board_init_fshould not be moved out ofmxc_nand_spl.c
to
either <board>/lowlevel_init.S or <board>/<board>.c. That would makemxc_nand_spl.cmore generic if for some reason a board needs to do specific things. Any opinion?Quoted 12 lines
For the
start.Sfiles, since it's not possible to know fromCONFIG_SPL_BUILD
andCONFIG_NAND_SPLifrelocate_codeis needed or not, I see the following choices:
1) Let it defined in all cases. It's quite small, so it won't hurt much.
2) Create a specific SPL #define (e.g.CONFIG_SPL_RELOCATE_CODE) to define it
for generic SPL only if needed.
3) Just create a specific linker section for it so that it's automatically garbage-collected if unneeded.
Any opinion?
Quoted 3 lines
I'm also considering to factorize
relocate_codetocrt0.S. There's not really a
good reason for it to be depending on each ARM processor. Any opinion?
FYI, I will post soon a v6 with a lot of cleanup.
Best regards,
Beno?t
PATCH v5 8/8 nand: mxc: Switch NAND SPL to generic SPL
Quoted 9 lines · Beno?t Th?baudeau
Hi Stefano,
Quoted 4 lines
I'm also considering to factorize
relocate_codetocrt0.S. There's not really a
good reason for it to be depending on each ARM processor. Any opinion?FYI, I will post soon a v6 with a lot of cleanup.
Ok, thanks.
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================