Skip to contentSkip to conversation

stm32m1 patches for v2017.10

PATCH New Patrick Delaunay 2 participants 19 messages Jun 21, 2019 – Jun 25, 2019

Subsystems (7)
lore
Share & tools
lore
#0 lore raw

cover stm32m1 patches for v2017.10

Some remaining patches for stm32mp1
- some cleanup in files
- add 2 specific commands for stm32mp1 board
- use OF_SYSTEM_SETUP to update kernel device tree
- synchronization with latest device tree

Patrick Delaunay (16):
stm32mp1: deactivate WATCHDOG in defconfig
stm32mp1: call regulators_enable_boot_on in board_init
stm32mp1: syscon: remove etzpc support
stm32mp1: syscon: remove stgen
dt-bindings: pinctrl: stm32: add new entry for package information
stm32mp1: export get_cpu_package function
stm32mp1: update package information in device tree
stm32mp1: update device tree with ETZPC status
stm32mp1: add stboard command
stm32mp1: key: add stm32key command
stm32mp1: udpate README
stm32mp1: cosmetic: remove unnecessary include
stm32mp1: configs: Add CONFIG_OF_SPL_REMOVE_PROPS
stm32mp1: add check for presence of environment in boot device
stm32mp1: force boot_net_usb_start
ARM: dts: stm32mp1: sync device tree with v5.2-rc4

 arch/arm/Kconfig                                   |   1 +
 arch/arm/dts/stm32mp15-ddr.dtsi                    |   2 +-
 arch/arm/dts/stm32mp157-pinctrl.dtsi               | 270 ++++++++++++++++++++-
 arch/arm/dts/stm32mp157-u-boot.dtsi                |  67 ++---
 arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi           |   4 -
 arch/arm/dts/stm32mp157a-dk1.dts                   |  30 ++-
 arch/arm/dts/stm32mp157c-dk2.dts                   |   1 +
 arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi           |  15 +-
 arch/arm/dts/stm32mp157c-ed1.dts                   | 205 ++++------------
 arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi           |   4 -
 arch/arm/dts/stm32mp157c-ev1.dts                   |  12 +-
 arch/arm/dts/stm32mp157c.dtsi                      | 199 +++++++++++----
 arch/arm/mach-stm32mp/Kconfig                      |  15 ++
 arch/arm/mach-stm32mp/Makefile                     |   2 +
 arch/arm/mach-stm32mp/cmd_stm32key.c               | 101 ++++++++
 arch/arm/mach-stm32mp/cpu.c                        |   7 +-
 arch/arm/mach-stm32mp/fdt.c                        | 223 +++++++++++++++++
 arch/arm/mach-stm32mp/include/mach/stm32.h         |   3 +-
 arch/arm/mach-stm32mp/include/mach/sys_proto.h     |   9 +
 arch/arm/mach-stm32mp/syscon.c                     |   2 -
 board/st/stm32mp1/Kconfig                          |   7 +
 board/st/stm32mp1/Makefile                         |   1 +
 board/st/stm32mp1/README                           |  15 +-
 board/st/stm32mp1/cmd_stboard.c                    | 145 +++++++++++
 board/st/stm32mp1/spl.c                            |   1 -
 board/st/stm32mp1/stm32mp1.c                       |   4 +
 configs/stm32mp15_basic_defconfig                  |   3 +-
 configs/stm32mp15_trusted_defconfig                |   2 -
 .../pinctrl/st,stm32-pinctrl.txt                   | 101 +++++++-
 drivers/clk/clk_stm32mp1.c                         |   3 +-
 include/configs/stm32mp1.h                         |   7 +-
 include/dt-bindings/pinctrl/stm32-pinfunc.h        |   6 +
 32 files changed, 1158 insertions(+), 309 deletions(-)
 create mode 100644 arch/arm/mach-stm32mp/cmd_stm32key.c
 create mode 100644 arch/arm/mach-stm32mp/fdt.c
 create mode 100644 board/st/stm32mp1/cmd_stboard.c
Signature · 1 line
2.7.4
#1 lore raw

PATCH 1/16 stm32mp1: deactivate WATCHDOG in defconfig

Deactivate WATCHDOG by default in u-boot to avoid issue to boot kernel and rootfs without the needed daemon to reload it.

---

 configs/stm32mp15_basic_defconfig   | 2 --
 configs/stm32mp15_trusted_defconfig | 2 --
 2 files changed, 4 deletions(-)
configs/stm32mp15_basic_defconfig +0 -2
index 4aa184f..b1fc3a2 100644
@@ -110,5 +110,3 @@ CONFIG_USB_GADGET_MANUFACTURER="STMicroelectronics"
 CONFIG_USB_GADGET_VENDOR_NUM=0x0483
 CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
 CONFIG_USB_GADGET_DWC2_OTG=y
-CONFIG_WDT=y
-CONFIG_WDT_STM32MP=y
configs/stm32mp15_trusted_defconfig +0 -2
index 66361c8..212b848 100644
@@ -100,5 +100,3 @@ CONFIG_USB_GADGET_MANUFACTURER="STMicroelectronics"
 CONFIG_USB_GADGET_VENDOR_NUM=0x0483
 CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
 CONFIG_USB_GADGET_DWC2_OTG=y
-CONFIG_WDT=y
-CONFIG_WDT_STM32MP=y
Signature · 1 line
2.7.4
#2 lore raw

PATCH 2/16 stm32mp1: call regulators_enable_boot_on in board_init

In reply to Patrick Delaunay

U-Boot activates regulators by reading the "regulator-boot-on" property in DT; it is requested by M4 early Boot feature.

---

 board/st/stm32mp1/stm32mp1.c | 4 ++++
 1 file changed, 4 insertions(+)
board/st/stm32mp1/stm32mp1.c +4 -0
index 7769293..e4d1723 100644
@@ -515,6 +515,10 @@ int board_init(void)
 
 	board_key_check();
 
+#ifdef CONFIG_DM_REGULATOR
+	regulators_enable_boot_on(_DEBUG);
+#endif
+
 	sysconf_init();
 
 	if (IS_ENABLED(CONFIG_LED))
Signature · 1 line
2.7.4
#3 lore raw

PATCH 3/16 stm32mp1: syscon: remove etzpc support

In reply to Patrick Delaunay

Support for ETZPC is removed as this device is not present in Linux kernel device tree.

---

 arch/arm/mach-stm32mp/include/mach/stm32.h | 1 -
 arch/arm/mach-stm32mp/syscon.c             | 1 -
 2 files changed, 2 deletions(-)
arch/arm/mach-stm32mp/include/mach/stm32.h +0 -1
index 6795352..1e3299a 100644
@@ -36,7 +36,6 @@
 /* enumerated used to identify the SYSCON driver instance */
 enum {
 	STM32MP_SYSCON_UNKNOWN,
-	STM32MP_SYSCON_ETZPC,
 	STM32MP_SYSCON_PWR,
 	STM32MP_SYSCON_STGEN,
 	STM32MP_SYSCON_SYSCFG,
arch/arm/mach-stm32mp/syscon.c +0 -1
index 242f834..e10c42e 100644
@@ -9,7 +9,6 @@
 #include <asm/arch/stm32.h>
 
 static const struct udevice_id stm32mp_syscon_ids[] = {
-	{ .compatible = "st,stm32mp1-etzpc", .data = STM32MP_SYSCON_ETZPC },
 	{ .compatible = "st,stm32mp1-pwr", .data = STM32MP_SYSCON_PWR },
 	{ .compatible = "st,stm32-stgen", .data = STM32MP_SYSCON_STGEN },
 	{ .compatible = "st,stm32mp157-syscfg",
Signature · 1 line
2.7.4
#4 lore raw

PATCH 4/16 stm32mp1: syscon: remove stgen

In reply to Patrick Delaunay

Reduce difference with kernel Linux device tree.

---

 arch/arm/dts/stm32mp157-u-boot.dtsi        | 7 -------
 arch/arm/mach-stm32mp/include/mach/stm32.h | 2 +-
 arch/arm/mach-stm32mp/syscon.c             | 1 -
 drivers/clk/clk_stm32mp1.c                 | 3 +--
 4 files changed, 2 insertions(+), 11 deletions(-)
arch/arm/dts/stm32mp157-u-boot.dtsi +0 -7
index 09560e2..c9f534e 100644
@@ -31,13 +31,6 @@
 
 	soc {
 		u-boot,dm-pre-reloc;
-
-		stgen: stgen at 5C008000 {
-			compatible = "st,stm32-stgen";
-			reg = <0x5C008000 0x1000>;
-			status = "okay";
-			u-boot,dm-pre-reloc;
-		};
 	};
 };
 
arch/arm/mach-stm32mp/include/mach/stm32.h +1 -1
index 1e3299a..1d4b548 100644
@@ -15,6 +15,7 @@
 #define STM32_DBGMCU_BASE		0x50081000
 #define STM32_TZC_BASE			0x5C006000
 #define STM32_ETZPC_BASE		0x5C007000
+#define STM32_STGEN_BASE		0x5C008000
 #define STM32_TAMP_BASE			0x5C00A000
 
 #define STM32_USART1_BASE		0x5C000000
@@ -37,7 +38,6 @@
 enum {
 	STM32MP_SYSCON_UNKNOWN,
 	STM32MP_SYSCON_PWR,
-	STM32MP_SYSCON_STGEN,
 	STM32MP_SYSCON_SYSCFG,
 };
 
arch/arm/mach-stm32mp/syscon.c +0 -1
index e10c42e..6070837 100644
@@ -10,7 +10,6 @@
 
 static const struct udevice_id stm32mp_syscon_ids[] = {
 	{ .compatible = "st,stm32mp1-pwr", .data = STM32MP_SYSCON_PWR },
-	{ .compatible = "st,stm32-stgen", .data = STM32MP_SYSCON_STGEN },
 	{ .compatible = "st,stm32mp157-syscfg",
 	  .data = STM32MP_SYSCON_SYSCFG },
 	{ }
drivers/clk/clk_stm32mp1.c +1 -2
index f295e48..5f15853 100644
@@ -1542,8 +1542,7 @@ static void stgen_config(struct stm32mp1_clk_priv *priv)
 	u32 stgenc, cntfid0;
 	ulong rate;
 
-	stgenc = (u32)syscon_get_first_range(STM32MP_SYSCON_STGEN);
-
+	stgenc = STM32_STGEN_BASE;
 	cntfid0 = readl(stgenc + STGENC_CNTFID0);
 	p = stm32mp1_clk_get_parent(priv, STGEN_K);
 	rate = stm32mp1_clk_get(priv, p);
Signature · 1 line
2.7.4
#5 lore raw

PATCH 5/16 dt-bindings: pinctrl: stm32: add new entry for package information

In reply to Patrick Delaunay

Add "st,package" entry. Possibles values are:
-STM32MP_PKG_AA for LFBGA448 (18*18) package
-STM32MP_PKG_AB for LFBGA354 (16*16) package
-STM32MP_PKG_AC for TFBGA361 (12*12) package
-STM32MP_PKG_AD for TFBGA257 (10*10) package

see Linux commit 966d9b928f626a54a0c27c0fdae1e3dfe9bab416 for v5.2-rc1

---

 .../pinctrl/st,stm32-pinctrl.txt                   | 101 ++++++++++++++++++---
 include/dt-bindings/pinctrl/stm32-pinfunc.h        |   6 ++
 2 files changed, 94 insertions(+), 13 deletions(-)
doc/device-tree-bindings/pinctrl/st,stm32-pinctrl.txt +88 -13
index c41ae91..0016925 100644
@@ -8,8 +8,13 @@ controllers onto these pads.
 Pin controller node:
 Required properies:
  - compatible: value should be one of the following:
-   (a) "st,stm32f429-pinctrl"
-   (b) "st,stm32f746-pinctrl"
+   "st,stm32f429-pinctrl"
+   "st,stm32f469-pinctrl"
+   "st,stm32f746-pinctrl"
+   "st,stm32f769-pinctrl"
+   "st,stm32h743-pinctrl"
+   "st,stm32mp157-pinctrl"
+   "st,stm32mp157-z-pinctrl"
  - #address-cells: The value of this property must be 1
  - #size-cells	: The value of this property must be 1
  - ranges	: defines mapping between pin controller node (parent) to
@@ -32,13 +37,30 @@ Required properties:
 
 Optional properties:
  - reset:	  : Reference to the reset controller
- - interrupt-parent: phandle of the interrupt parent to which the external
-   GPIO interrupts are forwarded to.
- - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node
-   which includes IRQ mux selection register, and the offset of the IRQ mux
-   selection register.
+ - st,syscfg: Should be phandle/offset/mask.
+	-The phandle to the syscon node which includes IRQ mux selection register.
+	-The offset of the IRQ mux selection register
+	-The field mask of IRQ mux, needed if different of 0xf.
+ - gpio-ranges: Define a dedicated mapping between a pin-controller and
+   a gpio controller. Format is <&phandle a b c> with:
+	-(phandle): phandle of pin-controller.
+	-(a): gpio base offset in range.
+	-(b): pin base offset in range.
+	-(c): gpio count in range
+   This entry has to be used either if there are holes inside a bank:
+	GPIOB0/B1/B2/B14/B15 (see example 2)
+   or if banks are not contiguous:
+	GPIOA/B/C/E...
+   NOTE: If "gpio-ranges" is used for a gpio controller, all gpio-controller
+   have to use a "gpio-ranges" entry.
+   More details in Documentation/devicetree/bindings/gpio/gpio.txt.
+ - st,bank-ioport: should correspond to the EXTI IOport selection (EXTI line
+   used to select GPIOs as interrupts).
+ - hwlocks: reference to a phandle of a hardware spinlock provider node.
+ - st,package: Indicates the SOC package used.
+   More details in include/dt-bindings/pinctrl/stm32-pinfunc.h
 
-Example:
+Example 1:
 #include <dt-bindings/pinctrl/stm32f429-pinfunc.h>
 ...
 
@@ -60,6 +82,43 @@ Example:
 		pin-functions nodes follow...
 	};
 
+Example 2:
+#include <dt-bindings/pinctrl/stm32f429-pinfunc.h>
+...
+
+	pinctrl: pin-controller {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,stm32f429-pinctrl";
+		ranges = <0 0x40020000 0x3000>;
+		pins-are-numbered;
+
+		gpioa: gpio at 40020000 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0x0 0x400>;
+			resets = <&reset_ahb1 0>;
+			st,bank-name = "GPIOA";
+			gpio-ranges = <&pinctrl 0 0 16>;
+		};
+
+		gpiob: gpio at 40020400 {
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0x0 0x400>;
+			resets = <&reset_ahb1 0>;
+			st,bank-name = "GPIOB";
+			ngpios = 4;
+			gpio-ranges = <&pinctrl 0 16 3>,
+				      <&pinctrl 14 30 2>;
+		};
+
+
+		...
+		pin-functions nodes follow...
+	};
+
+
 Contents of function subnode node:
 ----------------------------------
 Subnode format
@@ -83,14 +142,31 @@ Required properties:
     - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11)
     - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15)
     - function: The function number, can be:
-      * 0 : GPIO IN
+      * 0 : GPIO
       * 1 : Alternate Function 0
       * 2 : Alternate Function 1
       * 3 : Alternate Function 2
       * ...
       * 16 : Alternate Function 15
       * 17 : Analog
-      * 18 : GPIO OUT
+
+  To simplify the usage, macro is available to generate "pinmux" field.
+  This macro is available here:
+    - include/dt-bindings/pinctrl/stm32-pinfunc.h
+
+  Some examples of using macro:
+    /* GPIO A9 set as alernate function 2 */
+    ... {
+		pinmux = <STM32_PINMUX('A', 9, AF2)>;
+    };
+    /* GPIO A9 set as GPIO  */
+    ... {
+		pinmux = <STM32_PINMUX('A', 9, GPIO)>;
+    };
+    /* GPIO A9 set as analog */
+    ... {
+		pinmux = <STM32_PINMUX('A', 9, ANALOG)>;
+    };
 
 Optional properties:
 - GENERIC_PINCONFIG: is the generic pinconfig options to use.
@@ -114,13 +190,13 @@ pin-controller {
 ...
 	usart1_pins_a: usart1 at 0 {
 		pins1 {
-			pinmux = <STM32F429_PA9_FUNC_USART1_TX>;
+			pinmux = <STM32_PINMUX('A', 9, AF7)>;
 			bias-disable;
 			drive-push-pull;
 			slew-rate = <0>;
 		};
 		pins2 {
-			pinmux = <STM32F429_PA10_FUNC_USART1_RX>;
+			pinmux = <STM32_PINMUX('A', 10, AF7)>;
 			bias-disable;
 		};
 	};
@@ -129,5 +205,4 @@ pin-controller {
 &usart1 {
 	pinctrl-0 = <&usart1_pins_a>;
 	pinctrl-names = "default";
-	status = "okay";
 };
include/dt-bindings/pinctrl/stm32-pinfunc.h +6 -0
index b5a2174..e6fb8ad 100644
@@ -32,5 +32,11 @@
 
 #define STM32_PINMUX(port, line, mode) (((PIN_NO(port, line)) << 8) | (mode))
 
+/*  package information */
+#define STM32MP_PKG_AA	0x1
+#define STM32MP_PKG_AB	0x2
+#define STM32MP_PKG_AC	0x4
+#define STM32MP_PKG_AD	0x8
+
 #endif /* _DT_BINDINGS_STM32_PINFUNC_H */
 
Signature · 1 line
2.7.4
#6 lore raw

PATCH 6/16 stm32mp1: export get_cpu_package function

In reply to Patrick Delaunay

Prepare update of package information update
in Linux device tree.

---

 arch/arm/mach-stm32mp/cpu.c                    | 7 +------
 arch/arm/mach-stm32mp/include/mach/sys_proto.h | 9 +++++++++
 2 files changed, 10 insertions(+), 6 deletions(-)
arch/arm/mach-stm32mp/cpu.c +1 -6
index e1a0a13..d4f2ea8 100644
@@ -78,11 +78,6 @@
 #define PKG_SHIFT	27
 #define PKG_MASK	GENMASK(2, 0)
 
-#define PKG_AA_LBGA448	4
-#define PKG_AB_LBGA354	3
-#define PKG_AC_TFBGA361	2
-#define PKG_AD_TFBGA257	1
-
 #if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
 #ifndef CONFIG_STM32MP1_TRUSTED
 static void security_init(void)
@@ -277,7 +272,7 @@ u32 get_cpu_type(void)
 }
 
 /* Get Package options from OTP */
-static u32 get_cpu_package(void)
+u32 get_cpu_package(void)
 {
 	return get_otp(BSEC_OTP_PKG, PKG_SHIFT, PKG_MASK);
 }
arch/arm/mach-stm32mp/include/mach/sys_proto.h +9 -0
index 71a3ba7..99eefab 100644
@@ -19,5 +19,14 @@ u32 get_cpu_type(void);
 
 /* return CPU_REV constants */
 u32 get_cpu_rev(void);
+
+/* Get Package options from OTP */
+u32 get_cpu_package(void);
+
+#define PKG_AA_LBGA448	4
+#define PKG_AB_LBGA354	3
+#define PKG_AC_TFBGA361	2
+#define PKG_AD_TFBGA257	1
+
 /* return boot mode */
 u32 get_bootmode(void);
Signature · 1 line
2.7.4
#7 lore raw

PATCH 7/16 stm32mp1: update package information in device tree

In reply to Patrick Delaunay

---

 arch/arm/Kconfig               |  1 +
 arch/arm/mach-stm32mp/Makefile |  1 +
 arch/arm/mach-stm32mp/fdt.c    | 45 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 47 insertions(+)
 create mode 100644 arch/arm/mach-stm32mp/fdt.c
arch/arm/Kconfig +1 -0
index 01ff57c..a44cc3b 100644
@@ -1478,6 +1478,7 @@ config ARCH_STM32MP
 	select MISC
 	select OF_CONTROL
 	select OF_LIBFDT
+	select OF_SYSTEM_SETUP
 	select PINCTRL
 	select REGMAP
 	select SUPPORT_SPL
arch/arm/mach-stm32mp/Makefile +1 -0
index 1493914..e59bd81 100644
@@ -17,3 +17,4 @@ endif
 endif
 obj-$(CONFIG_ARMV7_PSCI) += psci.o
 obj-$(CONFIG_$(SPL_)DM_REGULATOR) += pwr_regulator.o
+obj-$(CONFIG_OF_SYSTEM_SETUP) += fdt.o
arch/arm/mach-stm32mp/fdt.c new file +45 -0

45 lines not on this page · raw message

Signature · 1 line
2.7.4
#8 lore raw

PATCH 8/16 stm32mp1: update device tree with ETZPC status

In reply to Patrick Delaunay

U-Boot should disable nodes in device tree if needed according ETZPC status in ft_system_setup().

ETZPC itself use an array on addresses to do the match between the status bits and the node.

---

 arch/arm/mach-stm32mp/Kconfig |   7 ++
 arch/arm/mach-stm32mp/fdt.c   | 178 ++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 185 insertions(+)
arch/arm/mach-stm32mp/Kconfig +7 -0
index d9ad6b4..9c5c93c 100644
@@ -83,6 +83,13 @@ config SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_MMC2
 	  Partition on the second MMC to load U-Boot from when the MMC is being
 	  used in raw mode
 
+config STM32_ETZPC
+	bool "STM32 Extended TrustZone Protection"
+	depends on TARGET_STM32MP1
+	default y
+	help
+	  Say y to enable STM32 Extended TrustZone Protection
+
 config BOOTSTAGE_STASH_ADDR
 	default 0xC3000000
 
arch/arm/mach-stm32mp/fdt.c +178 -0

190 lines not on this page · raw message

Signature · 1 line
2.7.4
#9 lore raw

PATCH 9/16 stm32mp1: add stboard command

In reply to Patrick Delaunay

Allow to update board identification in OTP 59.

---

 board/st/stm32mp1/Kconfig       |   7 ++
 board/st/stm32mp1/Makefile      |   1 +
 board/st/stm32mp1/cmd_stboard.c | 145 ++++++++++++++++++++++++++++++++++++++++
 3 files changed, 153 insertions(+)
 create mode 100644 board/st/stm32mp1/cmd_stboard.c
board/st/stm32mp1/Kconfig +7 -0
index 5ab9415..92d8f90 100644
@@ -9,4 +9,11 @@ config SYS_VENDOR
 config SYS_CONFIG_NAME
 	default "stm32mp1"
 
+config CMD_STBOARD
+	bool "stboard - command for OTP board information"
+	default y
+	help
+	  This compile the stboard command to
+	  read and write the board in the OTP.
+
 endif
board/st/stm32mp1/Makefile +1 -0
index 8188075..3c6c035 100644
@@ -7,6 +7,7 @@ ifdef CONFIG_SPL_BUILD
 obj-y += spl.o
 else
 obj-y += stm32mp1.o
+obj-$(CONFIG_CMD_STBOARD) += cmd_stboard.o
 endif
 
 obj-y += board.o
board/st/stm32mp1/cmd_stboard.c new file +145 -0

145 lines not on this page · raw message

Signature · 1 line
2.7.4
#10 lore raw

PATCH 10/16 stm32mp1: key: add stm32key command

In reply to Patrick Delaunay

Add dedicated command to register in fuse a public hash key provided by keygen tool.

---

 arch/arm/mach-stm32mp/Kconfig        |   8 +++
 arch/arm/mach-stm32mp/Makefile       |   1 +
 arch/arm/mach-stm32mp/cmd_stm32key.c | 101 +++++++++++++++++++++++++++++++++++
 3 files changed, 110 insertions(+)
 create mode 100644 arch/arm/mach-stm32mp/cmd_stm32key.c
arch/arm/mach-stm32mp/Kconfig +8 -0
index 9c5c93c..d13d76e 100644
@@ -90,6 +90,14 @@ config STM32_ETZPC
 	help
 	  Say y to enable STM32 Extended TrustZone Protection
 
+config CMD_STM32KEY
+	bool "command stm32key to fuse public key hash"
+	default y
+	depends on CMD_FUSE
+	help
+		fuse public key hash in corresponding fuse used to authenticate
+		binary.
+
 config BOOTSTAGE_STASH_ADDR
 	default 0xC3000000
 
arch/arm/mach-stm32mp/Makefile +1 -0
index e59bd81..7745060 100644
@@ -11,6 +11,7 @@ ifdef CONFIG_SPL_BUILD
 obj-y += spl.o
 else
 obj-y += bsec.o
+obj-$(CONFIG_CMD_STM32KEY) += cmd_stm32key.o
 ifndef CONFIG_STM32MP1_TRUSTED
 obj-$(CONFIG_SYSRESET) += cmd_poweroff.o
 endif
arch/arm/mach-stm32mp/cmd_stm32key.c new file +101 -0

101 lines not on this page · raw message

Signature · 1 line
2.7.4
#11 lore raw

PATCH 11/16 stm32mp1: udpate README

In reply to Patrick Delaunay

Add latest information and correct some information.

---

 board/st/stm32mp1/README | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)
board/st/stm32mp1/README +12 -3
index b0c8325..dc36a21 100644
@@ -25,6 +25,10 @@ It features:
 Everything is supported in Linux but U-Boot is limited to:
 1. UART
 2. SDCard/MMC controller (SDMMC)
+3. NAND controller (FMC)
+4. NOR controller (QSPI)
+5. USB controller (OTG DWC2)
+6. Ethernet controller
 
 And the necessary drivers
 1. I2C
@@ -54,13 +58,13 @@ with FSBL = First Stage Bootloader
    TF-A performs a full initialization of Secure peripherals and installs a
    secure monitor.
    U-Boot is running in normal world and uses TF-A monitor
-   to access to secure resources
+   to access to secure resources.
 
 2) The "Basic" boot chain (defconfig_file : stm32mp15_basic_defconfig)
    BootRom => FSBL = U-Boot SPL => SSBL = U-Boot
    SPL has limited security initialisation
    U-Boot is running in secure mode and provide a secure monitor to the kernel
-   with only PSCI support (Power State Coordination Interface defined by ARM)
+   with only PSCI support (Power State Coordination Interface defined by ARM).
 
 All the STM32MP1 boards supported by U-Boot use the same generic board
 stm32mp1 which support all the bootable devices.
@@ -111,6 +115,9 @@ the supported device trees for stm32mp157 are:
 	# export KBUILD_OUTPUT=stm32mp15_trusted
 	# export KBUILD_OUTPUT=stm32mp15_basic
 
+	you can build outside of code directory:
+	# export KBUILD_OUTPUT=../build/stm32mp15_trusted
+
 4. Configure U-Boot:
 
 	# make <defconfig_file>
@@ -170,6 +177,8 @@ the supported device trees for stm32mp157 are:
 
 You can select the boot mode, on the board ed1 with the switch SW1
 
+- on the daugther board ed1 with the switch SW1 : BOOT0, BOOT1, BOOT2
+
  -----------------------------------
   Boot Mode   BOOT2   BOOT1   BOOT0
  -----------------------------------
@@ -267,7 +276,7 @@ for example: with gpt table with 128 entries
 	# dd if=tf-a.stm32 of=/dev/mmcblk0p2
 	# dd if=u-boot.stm32 of=/dev/mmcblk0p3
 
-To boot from SDCard, select BootPinMode = 1 1 1 and reset.
+To boot from SDCard, select BootPinMode = 1 0 1 and reset.
 
 8. Prepare eMMC
 ===============
Signature · 1 line
2.7.4
#12 lore raw

PATCH 12/16 stm32mp1: cosmetic: remove unnecessary include

In reply to Patrick Delaunay

Remove post.h include as it is used in spl.c

---

 board/st/stm32mp1/spl.c | 1 -
 1 file changed, 1 deletion(-)
board/st/stm32mp1/spl.c +0 -1
index a7844f2..e19be0f 100644
@@ -9,7 +9,6 @@
 #include <dm.h>
 #include <ram.h>
 #include <asm/io.h>
-#include <post.h>
 #include <power/pmic.h>
 #include <power/stpmic1.h>
 #include <asm/arch/ddr.h>
Signature · 1 line
2.7.4
#13 lore raw

PATCH 13/16 stm32mp1: configs: Add CONFIG_OF_SPL_REMOVE_PROPS

In reply to Patrick Delaunay

Removes unused device tree property in SPL
to reduce the SPL size by 1kB

---

 configs/stm32mp15_basic_defconfig | 1 +
 1 file changed, 1 insertion(+)
configs/stm32mp15_basic_defconfig +1 -0
index b1fc3a2..965ea71 100644
@@ -43,6 +43,7 @@ CONFIG_CMD_MTDPARTS=y
 CONFIG_CMD_UBI=y
 # CONFIG_SPL_DOS_PARTITION is not set
 CONFIG_DEFAULT_DEVICE_TREE="stm32mp157c-ev1"
+CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
 CONFIG_ENV_IS_NOWHERE=y
 CONFIG_ENV_IS_IN_EXT4=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
Signature · 1 line
2.7.4
#14 lore raw

PATCH 14/16 stm32mp1: add check for presence of environment in boot device

In reply to Patrick Delaunay

For boot from flash, check presence of default environment to force save env.

---

 include/configs/stm32mp1.h | 4 ++++
 1 file changed, 4 insertions(+)
include/configs/stm32mp1.h +4 -0
index 1d385e0..6c74b4b 100644
@@ -112,6 +112,7 @@
 	"if test ${boot_device} = serial || test ${boot_device} = usb;" \
 	"then stm32prog ${boot_device} ${boot_instance}; " \
 	"else " \
+		"run env_check;" \
 		"if test ${boot_device} = mmc;" \
 		"then env set boot_targets \"mmc${boot_instance}\"; fi;" \
 		"if test ${boot_device} = nand;" \
@@ -143,6 +144,9 @@
 	"ramdisk_addr_r=0xc4400000\0" \
 	"fdt_high=0xffffffff\0" \
 	"initrd_high=0xffffffff\0" \
+	"env_default=1\0"				\
+	"env_check=if test $env_default -eq 1;"\
+		" then env set env_default 0;env save;fi\0" \
 	STM32MP_BOOTCMD \
 	STM32MP_MTDPARTS \
 	BOOTENV
Signature · 1 line
2.7.4
#15 lore raw

PATCH 15/16 stm32mp1: force boot_net_usb_start

In reply to Patrick Delaunay

Prevent USB enumeration and avoid unnecessary delay in bootcmd_pxe as Ethernet device is not attached to USB.

---

 include/configs/stm32mp1.h | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
include/configs/stm32mp1.h +2 -1
index 6c74b4b..94485a1 100644
@@ -149,7 +149,8 @@
 		" then env set env_default 0;env save;fi\0" \
 	STM32MP_BOOTCMD \
 	STM32MP_MTDPARTS \
-	BOOTENV
+	BOOTENV \
+	"boot_net_usb_start=true\0"
 
 #endif /* ifndef CONFIG_SPL_BUILD */
 #endif /* ifdef CONFIG_DISTRO_DEFAULTS*/
Signature · 1 line
2.7.4
#16 lore raw

PATCH 16/16 ARM: dts: stm32mp1: sync device tree with v5.2-rc4

In reply to Patrick Delaunay

Synchronize device tree with v5.2-rc4 label and
update the associated u-boot dtsi.

---

 arch/arm/dts/stm32mp15-ddr.dtsi          |   2 +-
 arch/arm/dts/stm32mp157-pinctrl.dtsi     | 270 ++++++++++++++++++++++++++++++-
 arch/arm/dts/stm32mp157-u-boot.dtsi      |  60 ++++---
 arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi |   4 -
 arch/arm/dts/stm32mp157a-dk1.dts         |  30 ++--
 arch/arm/dts/stm32mp157c-dk2.dts         |   1 +
 arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi |  15 +-
 arch/arm/dts/stm32mp157c-ed1.dts         | 205 +++++------------------
 arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi |   4 -
 arch/arm/dts/stm32mp157c-ev1.dts         |  12 +-
 arch/arm/dts/stm32mp157c.dtsi            | 199 +++++++++++++++++------
 11 files changed, 534 insertions(+), 268 deletions(-)
arch/arm/dts/stm32mp15-ddr.dtsi +1 -1
index 4172c02..0164e34 100644
@@ -5,7 +5,7 @@
 
 / {
 	soc {
-		ddr: ddr at 0x5A003000{
+		ddr: ddr at 5A003000{
 			u-boot,dm-pre-reloc;
 
 			compatible = "st,stm32mp1-ddr";
arch/arm/dts/stm32mp157-pinctrl.dtsi +262 -8

350 lines not on this page · raw message

arch/arm/dts/stm32mp157-u-boot.dtsi +36 -24

95 lines not on this page · raw message

arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi +0 -4
index 0f32a38..36c852d 100644
@@ -194,7 +194,3 @@
 	u-boot,force-b-session-valid;
 	hnp-srp-disable;
 };
-
-&v3v3 {
-	regulator-always-on;
-};
arch/arm/dts/stm32mp157a-dk1.dts +20 -10
index e36773d..c2b9c20 100644
@@ -39,6 +39,13 @@
 	};
 };
 
+&cec {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cec_pins_b>;
+	pinctrl-1 = <&cec_pins_sleep_b>;
+	status = "okay";
+};
+
 &ethernet0 {
 	status = "okay";
 	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
@@ -58,12 +65,14 @@
 	};
 };
 
+
 &i2c4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c4_pins_a>;
 	i2c-scl-rising-time-ns = <185>;
 	i2c-scl-falling-time-ns = <20>;
 	status = "okay";
+	/* spare dmas for other usage */
 	/delete-property/dmas;
 	/delete-property/dma-names;
 
@@ -88,17 +97,13 @@
 	pmic: stpmic at 33 {
 		compatible = "st,stpmic1";
 		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		status = "okay";
 
-		st,main-control-register = <0x04>;
-		st,vin-control-register = <0xc0>;
-		st,usb-control-register = <0x20>;
-
 		regulators {
 			compatible = "st,stpmic1-regulators";
-
 			ldo1-supply = <&v3v3>;
 			ldo3-supply = <&vdd_ddr>;
 			ldo6-supply = <&v3v3>;
@@ -107,7 +112,7 @@
 
 			vddcore: buck1 {
 				regulator-name = "vddcore";
-				regulator-min-microvolt = <1200000>;
+				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1350000>;
 				regulator-always-on;
 				regulator-initial-mode = <0>;
@@ -187,7 +192,6 @@
 				regulator-max-microvolt = <1200000>;
 				regulator-always-on;
 				interrupts = <IT_CURLIM_LDO6 0>;
-
 			};
 
 			vref_ddr: vref_ddr {
@@ -204,7 +208,6 @@
 			vbus_otg: pwr_sw1 {
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
-				regulator-active-discharge;
 			 };
 
 			 vbus_sw: pwr_sw2 {
@@ -216,8 +219,9 @@
 
 		onkey {
 			compatible = "st,stpmic1-onkey";
-			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
 			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
 			status = "okay";
 		};
 
@@ -228,6 +232,10 @@
 	};
 };
 
+&ipcc {
+	status = "okay";
+};
+
 &iwdg2 {
 	timeout-sec = <32>;
 	status = "okay";
@@ -246,8 +254,10 @@
 };
 
 &sdmmc1 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "opendrain", "sleep";
 	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
 	broken-cd;
 	st,neg-edge;
 	bus-width = <4>;
arch/arm/dts/stm32mp157c-dk2.dts +1 -0
index 9a81d2d..020ea0f 100644
@@ -42,6 +42,7 @@
 		compatible = "orisetech,otm8009a";
 		reg = <0>;
 		reset-gpios = <&gpioe 4 GPIO_ACTIVE_LOW>;
+		power-supply = <&v3v3>;
 		status = "okay";
 
 		port {
arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi +9 -6
index 55f9903..200601e 100644
@@ -156,6 +156,10 @@
 	};
 };
 
+&sdmmc1 {
+	u-boot,dm-spl;
+};
+
 &sdmmc1_b4_pins_a {
 	u-boot,dm-spl;
 	pins {
@@ -165,12 +169,15 @@
 
 &sdmmc1_dir_pins_a {
 	u-boot,dm-spl;
-	pins {
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
 		u-boot,dm-spl;
 	};
 };
 
-&sdmmc1 {
+&sdmmc2 {
 	u-boot,dm-spl;
 };
 
@@ -188,10 +195,6 @@
 	};
 };
 
-&sdmmc2 {
-	u-boot,dm-spl;
-};
-
 &uart4 {
 	u-boot,dm-pre-reloc;
 };
arch/arm/dts/stm32mp157c-ed1.dts +42 -163

352 lines not on this page · raw message

arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi +0 -4
index 5b19e44..56c9c7f 100644
@@ -59,7 +59,3 @@
 &usbotg_hs {
 	g-tx-fifo-size = <576>;
 };
-
-&v3v3 {
-	regulator-always-on;
-};
arch/arm/dts/stm32mp157c-ev1.dts +10 -2
index 663e52a..ca2a333 100644
@@ -6,6 +6,7 @@
 /dts-v1/;
 
 #include "stm32mp157c-ed1.dts"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "STMicroelectronics STM32MP157C eval daughter on eval mother";
@@ -157,8 +158,9 @@
 };
 
 &m_can1 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&m_can1_pins_a>;
+	pinctrl-1 = <&m_can1_sleep_pins_a>;
 	status = "okay";
 };
 
@@ -194,6 +196,9 @@
 };
 
 &timers2 {
+	/* spare dmas for other usage (un-delete to enable pwm capture) */
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "disabled";
 	pwm {
 		pinctrl-0 = <&pwm2_pins_a>;
@@ -206,6 +211,8 @@
 };
 
 &timers8 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "disabled";
 	pwm {
 		pinctrl-0 = <&pwm8_pins_a>;
@@ -218,6 +225,8 @@
 };
 
 &timers12 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "disabled";
 	pwm {
 		pinctrl-0 = <&pwm12_pins_a>;
@@ -232,7 +241,6 @@
 &usbh_ehci {
 	phys = <&usbphyc_port0>;
 	phy-names = "usb";
-	vbus-supply = <&vbus_sw>;
 	status = "okay";
 };
 
arch/arm/dts/stm32mp157c.dtsi +153 -46

363 lines not on this page · raw message

Signature · 1 line
2.7.4
#17 lore raw

cover stm32m1 patches for v2017.10

In reply to Patrick Delaunay

for v2019.10 ;-)

Quoted 63 lines · Patrick Delaunay

Some remaining patches for stm32mp1
- some cleanup in files
- add 2 specific commands for stm32mp1 board
- use OF_SYSTEM_SETUP to update kernel device tree
- synchronization with latest device tree

Patrick Delaunay (16):
stm32mp1: deactivate WATCHDOG in defconfig
stm32mp1: call regulators_enable_boot_on in board_init
stm32mp1: syscon: remove etzpc support
stm32mp1: syscon: remove stgen
dt-bindings: pinctrl: stm32: add new entry for package information
stm32mp1: export get_cpu_package function
stm32mp1: update package information in device tree
stm32mp1: update device tree with ETZPC status
stm32mp1: add stboard command
stm32mp1: key: add stm32key command
stm32mp1: udpate README
stm32mp1: cosmetic: remove unnecessary include
stm32mp1: configs: Add CONFIG_OF_SPL_REMOVE_PROPS
stm32mp1: add check for presence of environment in boot device
stm32mp1: force boot_net_usb_start
ARM: dts: stm32mp1: sync device tree with v5.2-rc4

 arch/arm/Kconfig                                   |   1 +
 arch/arm/dts/stm32mp15-ddr.dtsi                    |   2 +-
 arch/arm/dts/stm32mp157-pinctrl.dtsi               | 270 ++++++++++++++++++++-
 arch/arm/dts/stm32mp157-u-boot.dtsi                |  67 ++---
 arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi           |   4 -
 arch/arm/dts/stm32mp157a-dk1.dts                   |  30 ++-
 arch/arm/dts/stm32mp157c-dk2.dts                   |   1 +
 arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi           |  15 +-
 arch/arm/dts/stm32mp157c-ed1.dts                   | 205 ++++------------
 arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi           |   4 -
 arch/arm/dts/stm32mp157c-ev1.dts                   |  12 +-
 arch/arm/dts/stm32mp157c.dtsi                      | 199 +++++++++++----
 arch/arm/mach-stm32mp/Kconfig                      |  15 ++
 arch/arm/mach-stm32mp/Makefile                     |   2 +
 arch/arm/mach-stm32mp/cmd_stm32key.c               | 101 ++++++++
 arch/arm/mach-stm32mp/cpu.c                        |   7 +-
 arch/arm/mach-stm32mp/fdt.c                        | 223 +++++++++++++++++
 arch/arm/mach-stm32mp/include/mach/stm32.h         |   3 +-
 arch/arm/mach-stm32mp/include/mach/sys_proto.h     |   9 +
 arch/arm/mach-stm32mp/syscon.c                     |   2 -
 board/st/stm32mp1/Kconfig                          |   7 +
 board/st/stm32mp1/Makefile                         |   1 +
 board/st/stm32mp1/README                           |  15 +-
 board/st/stm32mp1/cmd_stboard.c                    | 145 +++++++++++
 board/st/stm32mp1/spl.c                            |   1 -
 board/st/stm32mp1/stm32mp1.c                       |   4 +
 configs/stm32mp15_basic_defconfig                  |   3 +-
 configs/stm32mp15_trusted_defconfig                |   2 -
 .../pinctrl/st,stm32-pinctrl.txt                   | 101 +++++++-
 drivers/clk/clk_stm32mp1.c                         |   3 +-
 include/configs/stm32mp1.h                         |   7 +-
 include/dt-bindings/pinctrl/stm32-pinfunc.h        |   6 +
 32 files changed, 1158 insertions(+), 309 deletions(-)
 create mode 100644 arch/arm/mach-stm32mp/cmd_stm32key.c
 create mode 100644 arch/arm/mach-stm32mp/fdt.c
 create mode 100644 board/st/stm32mp1/cmd_stboard.c
#18 lore raw

cover stm32m1 patches for v2017.10

Hi Patrice,

Quoted 4 lines

From: Patrice CHOTARD <[email protected]>
Sent: vendredi 21 juin 2019 15:55

for v2019.10 ;-)

Yes Sorry :-)

I mixed the first name (target as v2019.07) the new target v2019.10. I will update the serie title if I sent a v2.

Quoted 28 lines · Patrick Delaunay
Quoted 26 lines

Some remaining patches for stm32mp1
- some cleanup in files
- add 2 specific commands for stm32mp1 board
- use OF_SYSTEM_SETUP to update kernel device tree
- synchronization with latest device tree

Patrick Delaunay (16):
stm32mp1: deactivate WATCHDOG in defconfig
stm32mp1: call regulators_enable_boot_on in board_init
stm32mp1: syscon: remove etzpc support
stm32mp1: syscon: remove stgen
dt-bindings: pinctrl: stm32: add new entry for package information
stm32mp1: export get_cpu_package function
stm32mp1: update package information in device tree
stm32mp1: update device tree with ETZPC status
stm32mp1: add stboard command
stm32mp1: key: add stm32key command
stm32mp1: udpate README
stm32mp1: cosmetic: remove unnecessary include
stm32mp1: configs: Add CONFIG_OF_SPL_REMOVE_PROPS
stm32mp1: add check for presence of environment in boot device
stm32mp1: force boot_net_usb_start
ARM: dts: stm32mp1: sync device tree with v5.2-rc4

Quoted 38 lines
Quoted 3 lines
 arch/arm/Kconfig                                   |   1 +
 arch/arm/dts/stm32mp15-ddr.dtsi                    |   2 +-
 arch/arm/dts/stm32mp157-pinctrl.dtsi               | 270

++++++++++++++++++++-

Quoted 34 lines
 arch/arm/dts/stm32mp157-u-boot.dtsi                |  67 ++---
 arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi           |   4 -
 arch/arm/dts/stm32mp157a-dk1.dts                   |  30 ++-
 arch/arm/dts/stm32mp157c-dk2.dts                   |   1 +
 arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi           |  15 +-
 arch/arm/dts/stm32mp157c-ed1.dts                   | 205 ++++------------
 arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi           |   4 -
 arch/arm/dts/stm32mp157c-ev1.dts                   |  12 +-
 arch/arm/dts/stm32mp157c.dtsi                      | 199 +++++++++++----
 arch/arm/mach-stm32mp/Kconfig                      |  15 ++
 arch/arm/mach-stm32mp/Makefile                     |   2 +
 arch/arm/mach-stm32mp/cmd_stm32key.c               | 101 ++++++++
 arch/arm/mach-stm32mp/cpu.c                        |   7 +-
 arch/arm/mach-stm32mp/fdt.c                        | 223 +++++++++++++++++
 arch/arm/mach-stm32mp/include/mach/stm32.h         |   3 +-
 arch/arm/mach-stm32mp/include/mach/sys_proto.h     |   9 +
 arch/arm/mach-stm32mp/syscon.c                     |   2 -
 board/st/stm32mp1/Kconfig                          |   7 +
 board/st/stm32mp1/Makefile                         |   1 +
 board/st/stm32mp1/README                           |  15 +-
 board/st/stm32mp1/cmd_stboard.c                    | 145 +++++++++++
 board/st/stm32mp1/spl.c                            |   1 -
 board/st/stm32mp1/stm32mp1.c                       |   4 +
 configs/stm32mp15_basic_defconfig                  |   3 +-
 configs/stm32mp15_trusted_defconfig                |   2 -
 .../pinctrl/st,stm32-pinctrl.txt                   | 101 +++++++-
 drivers/clk/clk_stm32mp1.c                         |   3 +-
 include/configs/stm32mp1.h                         |   7 +-
 include/dt-bindings/pinctrl/stm32-pinfunc.h        |   6 +
 32 files changed, 1158 insertions(+), 309 deletions(-)  create mode
100644 arch/arm/mach-stm32mp/cmd_stm32key.c
 create mode 100644 arch/arm/mach-stm32mp/fdt.c  create mode 100644

board/st/stm32mp1/cmd_stboard.c

Regards

Patrick