Accessing BeagleBone Analog inputs
I followed the steps to create a beaglebone found here:
http://www.jumpnowtek.com/beaglebone/BeagleBone-Systems-with-Yocto.html
They worked like a charm, thanksyou junponowtek.
And then followed this doc to try and get the ADC available:
http://processors.wiki.ti.com/index.php/Linux_Core_ADC_Users_Guide
I loaded the module and it shows up in lsmod along with other modules it brings in:
# lsmod Module Size Used by ti_am335x_adc 16384 0 kfifo_buf 16384 1 ti_am335x_adc industrialio 57344 2 ti_am335x_adc,kfifo_buf ti_am335x_tscadc 16384 1 ti_am335x_adc
My arch/arm/boot/dts/am335x-evm.dts file shows
&tscadc {
status = "okay";
tsc {
ti,wires = <4>; ti,x-plate-resistance = <200>; ti,coordinate-readouts = <5>; ti,wire-config = <0x00 0x11 0x22 0x33>; ti,charge-delay = <0x400>;
};
adc {
ti,adc-channels = <4 5 6 7>;
};
};
According to the doc above loading the module should create the following:
Quoted 1 line
On loading the module you would see the IIO device created
root@arago-armv7:~# ls -al /sys/bus/iio/devices/iio\:device0/ drwxr-xr-x 5 root root 0 Nov 1 22:06 . drwxr-xr-x 4 root root 0 Nov 1 22:06 .. drwxr-xr-x 2 root root 0 Nov 1 22:06 buffer -r--r--r-- 1 root root 4096 Nov 1 22:06 dev -rw-r--r-- 1 root root 4096 Nov 1 22:06 in_voltage4_raw -rw-r--r-- 1 root root 4096 Nov 1 22:06 in_voltage5_raw -rw-r--r-- 1 root root 4096 Nov 1 22:06 in_voltage6_raw -rw-r--r-- 1 root root 4096 Nov 1 22:06 in_voltage7_raw -r--r--r-- 1 root root 4096 Nov 1 22:06 name lrwxrwxrwx 1 root root 0 Nov 1 22:06 of_node -> ../../../../../../firmware/devicetree/base/ocp/tscadc@44e0d000/adc drwxr-xr-x 2 root root 0 Nov 1 22:06 power drwxr-xr-x 2 root root 0 Nov 1 22:06 scan_elements lrwxrwxrwx 1 root root 0 Nov 1 22:06 subsystem -> ../../../../../../bus/iio -rw-r--r-- 1 root root 4096 Nov 1 22:06 uevent
While the /sys/bus/iio directory got created when I loaded the module the device directory is empty
# ls /sys/bus/iio/devices #
What am I missing that is preventing the ADC interface from being created ?
Any pointers would be appreciated.
Thanks
Chris K
You will probably have more luck getting an answer on the meta-ti mailing list:
https://lists.yoctoproject.org/listinfo/meta-ti
Quoted 74 lines · Chris Kottaridis
I followed the steps to create a beaglebone found here:
http://www.jumpnowtek.com/beaglebone/BeagleBone-Systems-with-Yocto.html
They worked like a charm, thanksyou junponowtek.
And then followed this doc to try and get the ADC available:
http://processors.wiki.ti.com/index.php/Linux_Core_ADC_Users_Guide
I loaded the module and it shows up in lsmod along with other modules it brings in:
# lsmod Module Size Used by ti_am335x_adc 16384 0 kfifo_buf 16384 1 ti_am335x_adc industrialio 57344 2 ti_am335x_adc,kfifo_buf ti_am335x_tscadc 16384 1 ti_am335x_adcMy
arch/arm/boot/dts/am335x-evm.dtsfile shows&tscadc { status = "okay"; tsc { ti,wires = <4>; ti,x-plate-resistance = <200>; ti,coordinate-readouts = <5>; ti,wire-config = <0x00 0x11 0x22 0x33>; ti,charge-delay = <0x400>; }; adc { ti,adc-channels = <4 5 6 7>; }; };According to the doc above loading the module should create the following:
Quoted 1 line
On loading the module you would see the IIO device created
root@arago-armv7:~# ls -al /sys/bus/iio/devices/iio\:device0/ drwxr-xr-x 5 root root 0 Nov 1 22:06 . drwxr-xr-x 4 root root 0 Nov 1 22:06 .. drwxr-xr-x 2 root root 0 Nov 1 22:06 buffer(quoted diff) +0
-6-r--r--r-- 1 root root 4096 Nov 1 22:06 dev -rw-r--r-- 1 root root 4096 Nov 1 22:06 in_voltage4_raw -rw-r--r-- 1 root root 4096 Nov 1 22:06 in_voltage5_raw -rw-r--r-- 1 root root 4096 Nov 1 22:06 in_voltage6_raw -rw-r--r-- 1 root root 4096 Nov 1 22:06 in_voltage7_raw -r--r--r-- 1 root root 4096 Nov 1 22:06 namelrwxrwxrwx 1 root root 0 Nov 1 22:06 of_node -> ../../../../../../firmware/devicetree/base/ocp/tscadc@44e0d000/adc drwxr-xr-x 2 root root 0 Nov 1 22:06 power drwxr-xr-x 2 root root 0 Nov 1 22:06 scan_elements lrwxrwxrwx 1 root root 0 Nov 1 22:06 subsystem -> ../../../../../../bus/iio -rw-r--r-- 1 root root 4096 Nov 1 22:06 ueventWhile the
/sys/bus/iiodirectory got created when I loaded the module the device directory is empty# ls /sys/bus/iio/devices #What am I missing that is preventing the ADC interface from being created ?
Any pointers would be appreciated.
Thanks
Chris KSignature · 4 lines
_______________________________________________ yocto mailing list [email protected] https://lists.yoctoproject.org/listinfo/yocto