Skip to contentSkip to conversation

tools/mesh-gatt: Add onoff set unack message to onoff client model

PATCH In review [email protected] 2 participants 2 messages Dec 3, 2021 – Dec 7, 2021 Bluetooth drivers

lore
Share & tools
lore
#0 lore raw

PATCH 1/6 tools/mesh-gatt: Add onoff set unack message to onoff client model

---
 tools/mesh-gatt/onoff-model.c | 23 +++++++++++++++++------
 1 file changed, 17 insertions(+), 6 deletions(-)
tools/mesh-gatt/onoff-model.c +16 -5
index 9dfedd85a..13ff4bbe3 100644
@@ -226,6 +226,8 @@ static void cmd_set(int argc, char *argv[])
 	uint16_t n;
 	uint8_t msg[32];
 	struct mesh_node *node;
+	int np;
+	uint32_t opcode;
 
 	if (IS_UNASSIGNED(target)) {
 		bt_shell_printf("Destination not set\n");
@@ -237,13 +239,22 @@ static void cmd_set(int argc, char *argv[])
 	if (!node)
 		return;
 
-	if ((read_input_parameters(argc, argv) != 1) &&
-					parms[0] != 0 && parms[0] != 1) {
-		bt_shell_printf("Bad arguments: Expecting \"0\" or
\"1\"\n");
-		return bt_shell_noninteractive_quit(EXIT_FAILURE);
+	np = read_input_parameters(argc, argv);
+	if ((np != 1) && (np != 2) &&
+		parms[0] != 0 && parms[0] != 1 &&
+		parms[1] != 0 && parms[1] != 1) {
+	bt_shell_printf("Bad arguments: Expecting \"0\" or \"1\" "
+		"and an optional \"0\" or \"1\" as unack\n");
+	return bt_shell_noninteractive_quit(EXIT_FAILURE);
+	}
+
+	if( (np==2) && parms[1] ){
+		opcode = OP_GENERIC_ONOFF_SET_UNACK;
+	}else{
+		opcode = OP_GENERIC_ONOFF_SET;
 	}
 
-	n = mesh_opcode_set(OP_GENERIC_ONOFF_SET, msg);
+	n = mesh_opcode_set(opcode, msg);
 	msg[n++] = parms[0];
 	msg[n++] = trans_id++;
 
@@ -263,7 +274,7 @@ static const struct bt_shell_menu onoff_menu = {
 						"Set node to configure"},
 	{"get",			NULL,

cmd_get_status,
"Get ON/OFF status"},
- {"onoff", "<0/1>", cmd_set,
+ {"onoff", "<0/1> [unack]", cmd_set,
"Send \"SET ON/OFF\"
command"},
{} },
};

Signature · 1 line
2.25.1
#1 lore raw

Hi Daniel,

Please add the commit message for each patches.
And the CI bot was not able to apply the patch. Please resubmit after rebasing to the tip.

Regards,
Tedd

Quoted 57 lines · On Fri, 2021-12-03 at 17:02 +0100, [email protected] wrote:

---
 tools/mesh-gatt/onoff-model.c | 23 +++++++++++++++++------

 1 file changed, 17 insertions(+), 6 deletions(-)
tools/mesh-gatt/onoff-model.c +2 -0
index 9dfedd85a..13ff4bbe3 100644
@@ -226,6 +226,8 @@ static void cmd_set(int argc, char *argv[])
         uint16_t n;
         uint8_t msg[32];
         struct mesh_node *node;
+       int np;
+       uint32_t opcode;


        if (IS_UNASSIGNED(target)) { bt_shell_printf("Destination not set\n");

tools/mesh-gatt/onoff-model.c +0 -0
@@ -237,13 +239,22 @@ static void cmd_set(int argc, char *argv[])
         if (!node)
                 return;


-       if ((read_input_parameters(argc, argv) != 1) &&
-                                       parms[0] != 0 && parms[0] != 1) { -               bt_shell_printf("Bad arguments: Expecting \"0\" or \"1\"\n");
-               return bt_shell_noninteractive_quit(EXIT_FAILURE); +       np = read_input_parameters(argc, argv);
+       if ((np != 1) && (np != 2) &&
+               parms[0] != 0 && parms[0] != 1 &&
+               parms[1] != 0 && parms[1] != 1) {
+       bt_shell_printf("Bad arguments: Expecting \"0\" or \"1\" " +               "and an optional \"0\" or \"1\" as unack\n"); +       return bt_shell_noninteractive_quit(EXIT_FAILURE);
+       }
+
+       if( (np==2) && parms[1] ){
+               opcode = OP_GENERIC_ONOFF_SET_UNACK;
+       }else{
+               opcode = OP_GENERIC_ONOFF_SET;
        }

-       n = mesh_opcode_set(OP_GENERIC_ONOFF_SET, msg);
+       n = mesh_opcode_set(opcode, msg);
        msg[n++] = parms[0];
        msg[n++] = trans_id++;

tools/mesh-gatt/onoff-model.c +1 -1
@@ -263,7 +274,7 @@ static const struct bt_shell_menu onoff_menu = {
                                                 "Set node to configure"},
         {"get",                 NULL,
 cmd_get_status,
                                                 "Get ON/OFF status"},
-       {"onoff",               "<0/1>",                        cmd_set,
+       {"onoff",               "<0/1> [unack]",                cmd_set,

                                                "Send \"SET ON/OFF\" command"},
        {} },
 };