Skip to contentSkip to conversation

PCI: rcar: Add L1 link state fix into data abort hook

PATCH Superseded [email protected] 4 participants 9 messages Sep 26, 2020 – Oct 7, 2020

Subsystems (4)

v2 of 7 Superseded Latest is v7 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 PCI: rcar: Add L1 link state fix into data abort hook

From: Marek Vasut <[email protected]>

The R-Car PCIe controller is capable of handling L0s/L1 link states. While the controller can enter and exit L0s link state, and exit L1 link state, without any additional action from the driver, to enter L1 link state, the driver must complete the link state transition by issuing additional commands to the controller.

The problem is, this transition is not atomic. The controller sets PMEL1RX bit in PMSR register upon reception of PM_ENTER_L1 DLLP from the PCIe card, but then the controller enters some sort of inbetween state. The driver must detect this condition and complete the link state transition, by setting L1IATN bit in PMCTLR and waiting for the link state transition to complete.

If a PCIe access happens inside of this window, where the controller is inbetween L0 and L1 link states, the access generates a fault and the ARM 'imprecise external abort' handler is invoked.

Just like other PCI controller drivers, here we hook the fault handler, perform the fixup to help the controller enter L1 link state, and then restart the instruction which triggered the fault. Since the controller is in L1 link state now, the link can exit from L1 link state to L0 and successfully complete the access.

Note that this fixup is applicable only to Aarch32 R-Car controllers,
the Aarch64 R-Car perform the same fixup in TFA, see TFA commit [1]
0969397f2 ("rcar_gen3: plat: Prevent PCIe hang during L1X config access")
[1] https://github.com/ARM-software/arm-trusted-firmware/commit/0969397f295621aa26b3d14b76dd397d22be58bf

Cc Bjorn Helgaas <[email protected]>
Cc Geert Uytterhoeven <[email protected]>
Cc Lorenzo Pieralisi <[email protected]>
Cc Wolfram Sang <[email protected]>
Cc Yoshihiro Shimoda <[email protected]>

---
V2: - Update commit message, add link to TFA repository commit
- Handle the LPAE case as in ARM fault.c and fsr-{2,3}level.c
- Cache clock and check whether they are enabled before register access

---
 drivers/pci/controller/pcie-rcar-host.c | 65 +++++++++++++++++++++++++
 drivers/pci/controller/pcie-rcar.h      |  7 +++
 2 files changed, 72 insertions(+)
drivers/pci/controller/pcie-rcar-host.c +65 -0
index cdc0963f154e..f8ff8c55716a 100644
@@ -13,6 +13,7 @@
 
 #include <linux/bitops.h>
 #include <linux/clk.h>
+#include <linux/clk-provider.h>
 #include <linux/delay.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
@@ -42,6 +43,21 @@ struct rcar_msi {
 	int irq2;
 };
 
+#ifdef CONFIG_ARM
+/*
+ * Here we keep a static copy of the remapped PCIe controller address.
+ * This is only used on aarch32 systems, all of which have one single
+ * PCIe controller, to provide quick access to the PCIe controller in
+ * the L1 link state fixup function, called from ARM fault handler.
+ */
+static void __iomem *pcie_base;
+/*
+ * Static copy of bus clock pointer, so we can check whether the clock
+ * are enabled or not.
+ */
+static struct clk *pcie_bus_clk;
+#endif
+
 static inline struct rcar_msi *to_rcar_msi(struct msi_controller *chip)
 {
 	return container_of(chip, struct rcar_msi, chip);
@@ -804,6 +820,12 @@ static int rcar_pcie_get_resources(struct rcar_pcie_host *host)
 	}
 	host->msi.irq2 = i;
 
+#ifdef CONFIG_ARM
+	/* Cache static copy for L1 link state fixup hook on aarch32 */
+	pcie_base = pcie->base;
+	pcie_bus_clk = host->bus_clk;
+#endif
+
 	return 0;
 
 err_irq2:
@@ -1050,4 +1072,47 @@ static struct platform_driver rcar_pcie_driver = {
 	},
 	.probe = rcar_pcie_probe,
 };
+
+#ifdef CONFIG_ARM
+static int rcar_pcie_aarch32_abort_handler(unsigned long addr,
+		unsigned int fsr, struct pt_regs *regs)
+{
+	u32 pmsr;
+
+	if (!pcie_base || !pcie_bus_clk || !__clk_is_enabled(pcie_bus_clk))
+		return 1;
+
+	pmsr = readl(pcie_base + PMSR);
+
+	/*
+	 * Test if the PCIe controller received PM_ENTER_L1 DLLP and
+	 * the PCIe controller is not in L1 link state. If true, apply
+	 * fix, which will put the controller into L1 link state, from
+	 * which it can return to L0s/L0 on its own.
+	 */
+	if ((pmsr & PMEL1RX) && ((pmsr & PMSTATE) != PMSTATE_L1)) {
+		writel(L1IATN, pcie_base + PMCTLR);
+		while (!(readl(pcie_base + PMSR) & L1FAEG))
+			;
+		writel(L1FAEG | PMEL1RX, pcie_base + PMSR);
+		return 0;
+	}
+
+	return 1;
+}
+
+static int __init rcar_pcie_init(void)
+{
+#ifdef CONFIG_ARM_LPAE
+	hook_fault_code(17, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+			"asynchronous external abort");
+#else
+	hook_fault_code(22, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+			"imprecise external abort");
+#endif
+	return platform_driver_register(&rcar_pcie_driver);
+}
+device_initcall(rcar_pcie_init);
+#else
 builtin_platform_driver(rcar_pcie_driver);
+#endif
drivers/pci/controller/pcie-rcar.h +7 -0
index d4c698b5f821..9bb125db85c6 100644
@@ -85,6 +85,13 @@
 #define  LTSMDIS		BIT(31)
 #define  MACCTLR_INIT_VAL	(LTSMDIS | MACCTLR_NFTS_MASK)
 #define PMSR			0x01105c
+#define  L1FAEG			BIT(31)
+#define  PMEL1RX		BIT(23)
+#define  PMSTATE		GENMASK(18, 16)
+#define  PMSTATE_L1		(3 << 16)
+#define PMCTLR			0x011060
+#define  L1IATN			BIT(31)
+
 #define MACS2R			0x011078
 #define MACCGSPSETR		0x011084
 #define  SPCNGRSN		BIT(31)
Signature · 1 line
2.28.0
#1 lore raw

Hello!

Quoted 8 lines · On 26.09.2020 19:09, [email protected] wrote:

From: Marek Vasut <[email protected]>

The R-Car PCIe controller is capable of handling L0s/L1 link states. While the controller can enter and exit L0s link state, and exit L1 link state, without any additional action from the driver, to enter L1 link state, the driver must complete the link state transition by issuing additional commands to the controller.

Quoted 8 lines

The problem is, this transition is not atomic. The controller sets PMEL1RX bit in PMSR register upon reception of PM_ENTER_L1 DLLP from the PCIe card, but then the controller enters some sort of inbetween state. The driver must detect this condition and complete the link state transition, by setting L1IATN bit in PMCTLR and waiting for the link state transition to complete.

If a PCIe access happens inside of this window, where the controller

    s/of//.
Quoted 1 line

is inbetween L0 and L1 link states, the access generates a fault and

My spellchecker trips on "inbetween"...

Quoted 5 lines

the ARM 'imprecise external abort' handler is invoked.

Just like other PCI controller drivers, here we hook the fault handler, perform the fixup to help the controller enter L1 link state, and then restart the instruction which triggered the fault. Since the controller

If this is imprecise or async external abort, how we can re-execute the
instruction that triggered the fault? It's been probably executed already, no?

Quoted 15 lines

is in L1 link state now, the link can exit from L1 link state to L0 and successfully complete the access.

Note that this fixup is applicable only to Aarch32 R-Car controllers,
the Aarch64 R-Car perform the same fixup in TFA, see TFA commit [1]
0969397f2 ("rcar_gen3: plat: Prevent PCIe hang during L1X config access")
[1] https://github.com/ARM-software/arm-trusted-firmware/commit/0969397f295621aa26b3d14b76dd397d22be58bf

Cc Bjorn Helgaas <[email protected]>
Cc Geert Uytterhoeven <[email protected]>
Cc Lorenzo Pieralisi <[email protected]>
Cc Wolfram Sang <[email protected]>
Cc Yoshihiro Shimoda <[email protected]>

[...]

Quoted 5 lines
drivers/pci/controller/pcie-rcar-host.c +5 -0
+static int __init rcar_pcie_init(void)
+{
+#ifdef CONFIG_ARM_LPAE
+	hook_fault_code(17, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+			"asynchronous external abort");

drivers/pci/controller/pcie-rcar-host.c static struct platform_driver rcar_pcie_driver = { · line 1118

Quoted 10 lines
drivers/pci/controller/pcie-rcar-host.c +9 -0
+#else
+	hook_fault_code(22, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+			"imprecise external abort");
+#endif
+	return platform_driver_register(&rcar_pcie_driver);
+}
+device_initcall(rcar_pcie_init);
+#else
  builtin_platform_driver(rcar_pcie_driver);
+#endif

[...]

MBR, Sergei

#2 lore raw

On 9/27/20 10:29 AM, Sergei Shtylyov wrote:
[...]

Quoted 9 lines
Quoted 5 lines

the ARM 'imprecise external abort' handler is invoked.

Just like other PCI controller drivers, here we hook the fault handler, perform the fixup to help the controller enter L1 link state, and then restart the instruction which triggered the fault. Since the controller

   If this is imprecise or async external abort, how we can re-execute the instruction that triggered the fault? It's been probably executed already, no?

It has been executed and triggered the fault, because it could not access the data across the bus. Now the bus is back in operational state, so restart the instruction, let it access the data and do its task.

[...]

Tested-by on v2 1/1
#3 lore raw
In reply to [email protected]

Hi Marek,

Quoted 37 lines · On Sat, Sep 26, 2020 at 6:09 PM <[email protected]> wrote:

From: Marek Vasut <[email protected]>

The R-Car PCIe controller is capable of handling L0s/L1 link states. While the controller can enter and exit L0s link state, and exit L1 link state, without any additional action from the driver, to enter L1 link state, the driver must complete the link state transition by issuing additional commands to the controller.

The problem is, this transition is not atomic. The controller sets PMEL1RX bit in PMSR register upon reception of PM_ENTER_L1 DLLP from the PCIe card, but then the controller enters some sort of inbetween state. The driver must detect this condition and complete the link state transition, by setting L1IATN bit in PMCTLR and waiting for the link state transition to complete.

If a PCIe access happens inside of this window, where the controller is inbetween L0 and L1 link states, the access generates a fault and the ARM 'imprecise external abort' handler is invoked.

Just like other PCI controller drivers, here we hook the fault handler, perform the fixup to help the controller enter L1 link state, and then restart the instruction which triggered the fault. Since the controller is in L1 link state now, the link can exit from L1 link state to L0 and successfully complete the access.

Note that this fixup is applicable only to Aarch32 R-Car controllers,
the Aarch64 R-Car perform the same fixup in TFA, see TFA commit [1]
0969397f2 ("rcar_gen3: plat: Prevent PCIe hang during L1X config access")
[1] https://github.com/ARM-software/arm-trusted-firmware/commit/0969397f295621aa26b3d14b76dd397d22be58bf

Cc Bjorn Helgaas <[email protected]>
Cc Geert Uytterhoeven <[email protected]>
Cc Lorenzo Pieralisi <[email protected]>
Cc Wolfram Sang <[email protected]>
Cc Yoshihiro Shimoda <[email protected]>
Quoted 5 lines

---
V2: - Update commit message, add link to TFA repository commit
- Handle the LPAE case as in ARM fault.c and fsr-{2,3}level.c
- Cache clock and check whether they are enabled before register access

Thanks for the update!

Quoted 11 lines
drivers/pci/controller/pcie-rcar-host.c +1 -0
@@ -13,6 +13,7 @@
 
 #include <linux/bitops.h>
 #include <linux/clk.h>
+#include <linux/clk-provider.h>
 #include <linux/delay.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>

drivers/pci/controller/pcie-rcar-host.c struct rcar_msi { · line 51

Quoted 9 lines
drivers/pci/controller/pcie-rcar-host.c +6 -0
@@ -42,6 +43,21 @@ struct rcar_msi {
        int irq2;
 };
 
+#ifdef CONFIG_ARM
+/*
+ * Here we keep a static copy of the remapped PCIe controller address.
+ * This is only used on aarch32 systems, all of which have one single
+ * PCIe controller, to provide quick access to the PCIe controller in
+ * the L1 link state fixup function, called from ARM fault handler.

the ARM fault handler

drivers/pci/controller/pcie-rcar-host.c struct rcar_msi { · line 56

Quoted 5 lines
drivers/pci/controller/pcie-rcar-host.c +5 -0
+ */
+static void __iomem *pcie_base;
+/*
+ * Static copy of bus clock pointer, so we can check whether the clock
+ * are enabled or not.

is

Quoted 6 lines
drivers/pci/controller/pcie-rcar-host.c +3 -0
+ */
+static struct clk *pcie_bus_clk;
+#endif
 
@@ -1050,4 +1072,47 @@ static struct platform_driver rcar_pcie_driver = {
        },

drivers/pci/controller/pcie-rcar-host.c static struct platform_driver rcar_pcie_driver = { · line 1082

Quoted 10 lines
drivers/pci/controller/pcie-rcar-host.c +8 -0
        .probe = rcar_pcie_probe,
 };
+
+#ifdef CONFIG_ARM
+static int rcar_pcie_aarch32_abort_handler(unsigned long addr,
+               unsigned int fsr, struct pt_regs *regs)
+{
+       u32 pmsr;
+
+       if (!pcie_base || !pcie_bus_clk || !__clk_is_enabled(pcie_bus_clk))

As __clk_is_enabled() handles a NULL pointer parameter, the second test is not needed.

Quoted 4 lines
drivers/pci/controller/pcie-rcar-host.c +4 -0
+               return 1;
+
+       pmsr = readl(pcie_base + PMSR);
+

drivers/pci/controller/pcie-rcar-host.c static struct platform_driver rcar_pcie_driver = { · line 1096

Quoted 10 lines
drivers/pci/controller/pcie-rcar-host.c +10 -0
+       /*
+        * Test if the PCIe controller received PM_ENTER_L1 DLLP and
+        * the PCIe controller is not in L1 link state. If true, apply
+        * fix, which will put the controller into L1 link state, from
+        * which it can return to L0s/L0 on its own.
+        */
+       if ((pmsr & PMEL1RX) && ((pmsr & PMSTATE) != PMSTATE_L1)) {
+               writel(L1IATN, pcie_base + PMCTLR);
+               while (!(readl(pcie_base + PMSR) & L1FAEG))
+                       ;

To answer my own question from previous review cycle: this takes 7 cycles on r8a7791/koelsch.

Quoted 6 lines
drivers/pci/controller/pcie-rcar-host.c +6 -0
+               writel(L1FAEG | PMEL1RX, pcie_base + PMSR);
+               return 0;
+       }
+
+       return 1;
+}

drivers/pci/controller/pcie-rcar-host.c static struct platform_driver rcar_pcie_driver = { · line 1112

Quoted 10 lines
drivers/pci/controller/pcie-rcar-host.c +10 -0
+
+static int __init rcar_pcie_init(void)
+{
+#ifdef CONFIG_ARM_LPAE
+       hook_fault_code(17, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+                       "asynchronous external abort");
+#else
+       hook_fault_code(22, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+                       "imprecise external abort");
+#endif

As there can be only a single handler, this may interfere with a handler for another platform in a multi-platform kernel.
Hence I think this should not be done unconditionally, but be moved to the driver's .probe() callback.

drivers/pci/controller/pcie-rcar-host.c static struct platform_driver rcar_pcie_driver = { · line 1118

Quoted 6 lines
drivers/pci/controller/pcie-rcar-host.c +5 -0
+       return platform_driver_register(&rcar_pcie_driver);
+}
+device_initcall(rcar_pcie_init);
+#else
 builtin_platform_driver(rcar_pcie_driver);
+#endif

As this fixes the crash seen during s2ram with an Intel E1000E card present and the e1000e driver loaded:

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

#4 lore raw

On 9/28/20 11:35 AM, Geert Uytterhoeven wrote:
[...]

Quoted 6 lines
Quoted 6 lines
drivers/pci/controller/pcie-rcar-host.c +6 -0
+static int __init rcar_pcie_init(void)
+{
+#ifdef CONFIG_ARM_LPAE
+       hook_fault_code(17, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+                       "asynchronous external abort");
+#else
Quoted 8 lines

drivers/pci/controller/pcie-rcar-host.c static struct platform_driver rcar_pcie_driver = { · line 1112

Quoted 3 lines
drivers/pci/controller/pcie-rcar-host.c +3 -0
+       hook_fault_code(22, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+                       "imprecise external abort");
+#endif

As there can be only a single handler, this may interfere with a handler for another platform in a multi-platform kernel.
Hence I think this should not be done unconditionally, but be moved to the driver's .probe() callback.

Why is nobody doing this in the probe code then ? It seems all the other drivers which hook fault code do it in init as well. I can imagine that something might trip the fault handler even before probe is called, e.g. some PM handling or simply user accessing that PCIe area using setpci.

[...]

#5 lore raw

Hi Marek,

Quoted 17 lines · Marek Vasut

On 9/28/20 11:35 AM, Geert Uytterhoeven wrote:
[...]

Quoted 6 lines
Quoted 6 lines
drivers/pci/controller/pcie-rcar-host.c +6 -0
+static int __init rcar_pcie_init(void)
+{
+#ifdef CONFIG_ARM_LPAE
+       hook_fault_code(17, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+                       "asynchronous external abort");
+#else
Quoted 8 lines

drivers/pci/controller/pcie-rcar-host.c static struct platform_driver rcar_pcie_driver = { · line 1112

Quoted 3 lines
drivers/pci/controller/pcie-rcar-host.c +3 -0
+       hook_fault_code(22, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+                       "imprecise external abort");
+#endif

As there can be only a single handler, this may interfere with a handler for another platform in a multi-platform kernel.
Hence I think this should not be done unconditionally, but be moved to the driver's .probe() callback.

Quoted 1 line

Why is nobody doing this in the probe code then ? It seems all the other

drivers/pci/controller/dwc/pci-keystone.c is:

ks_pcie_probe()

    ks_pcie_add_pcie_port()
      dw_pcie_host_init()
        pp->ops->host_init(pp) = ks_pcie_host_init()
          hook_fault_code()
Quoted 1 line

drivers which hook fault code do it in init as well. I can imagine that

Probably nobody bothered exercising the external abort handler on multi-platform kernels?

Quoted 2 lines

something might trip the fault handler even before probe is called, e.g. some PM handling or simply user accessing that PCIe area using setpci.

If that is the case, it must indeed by done earlier, but still conditional on the presence of the actual PCIe controller.

Gr{oetje,eeting}s,

Geert

Signature · 5 lines
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds
#6 lore raw
Quoted 1 line · Geert Uytterhoeven

Hi Marek,

Hi,

Quoted 20 lines · Marek Vasut
Quoted 17 lines · Geert Uytterhoeven

[...]

Quoted 6 lines
Quoted 6 lines
drivers/pci/controller/pcie-rcar-host.c +6 -0
+static int __init rcar_pcie_init(void)
+{
+#ifdef CONFIG_ARM_LPAE
+       hook_fault_code(17, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+                       "asynchronous external abort");
+#else
Quoted 8 lines

drivers/pci/controller/pcie-rcar-host.c static struct platform_driver rcar_pcie_driver = { · line 1112

Quoted 3 lines
drivers/pci/controller/pcie-rcar-host.c +3 -0
+       hook_fault_code(22, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+                       "imprecise external abort");
+#endif

As there can be only a single handler, this may interfere with a handler for another platform in a multi-platform kernel.
Hence I think this should not be done unconditionally, but be moved to the driver's .probe() callback.

Quoted 1 line

Why is nobody doing this in the probe code then ? It seems all the other

Quoted 7 lines

drivers/pci/controller/dwc/pci-keystone.c is:

ks_pcie_probe()

    ks_pcie_add_pcie_port()
      dw_pcie_host_init()
        pp->ops->host_init(pp) = ks_pcie_host_init()
          hook_fault_code()

Well that one is interesting. I wonder whether that driver has the same LPAE bug (different fault code for LPAE and non-LPAE configuration) we found here too, since it is used on CA15 TI SoCs.

Quoted 10 lines
Quoted 1 line

drivers which hook fault code do it in init as well. I can imagine that

Probably nobody bothered exercising the external abort handler on multi-platform kernels?

Quoted 2 lines

something might trip the fault handler even before probe is called, e.g. some PM handling or simply user accessing that PCIe area using setpci.

If that is the case, it must indeed by done earlier, but still conditional on the presence of the actual PCIe controller.

I am open to suggestions how to do that part.

#7 lore raw

Hi Marek,

Quoted 29 lines · Marek Vasut
Quoted 20 lines · Geert Uytterhoeven
Quoted 17 lines · Marek Vasut

On 9/28/20 11:35 AM, Geert Uytterhoeven wrote:
[...]

Quoted 6 lines
Quoted 6 lines
drivers/pci/controller/pcie-rcar-host.c +6 -0
+static int __init rcar_pcie_init(void)
+{
+#ifdef CONFIG_ARM_LPAE
+       hook_fault_code(17, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+                       "asynchronous external abort");
+#else
Quoted 8 lines

drivers/pci/controller/pcie-rcar-host.c static struct platform_driver rcar_pcie_driver = { · line 1112

Quoted 3 lines
drivers/pci/controller/pcie-rcar-host.c +3 -0
+       hook_fault_code(22, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+                       "imprecise external abort");
+#endif

As there can be only a single handler, this may interfere with a handler for another platform in a multi-platform kernel.
Hence I think this should not be done unconditionally, but be moved to the driver's .probe() callback.

Quoted 1 line

Why is nobody doing this in the probe code then ? It seems all the other

Quoted 7 lines

drivers/pci/controller/dwc/pci-keystone.c is:

ks_pcie_probe()

    ks_pcie_add_pcie_port()
      dw_pcie_host_init()
        pp->ops->host_init(pp) = ks_pcie_host_init()
          hook_fault_code()
Quoted 3 lines

Well that one is interesting. I wonder whether that driver has the same LPAE bug (different fault code for LPAE and non-LPAE configuration) we found here too, since it is used on CA15 TI SoCs.

Isn't that an ARM "feature"?

    arch/arm/mm/fault.c-/* FSR definition */
    arch/arm/mm/fault.c:#ifdef CONFIG_ARM_LPAE
    arch/arm/mm/fault.c-#include "fsr-3level.c"
    arch/arm/mm/fault.c-#else
    arch/arm/mm/fault.c-#include "fsr-2level.c"
    arch/arm/mm/fault.c-#endif
Quoted 5 lines
Quoted 5 lines
Quoted 1 line

drivers which hook fault code do it in init as well. I can imagine that

Probably nobody bothered exercising the external abort handler on multi-platform kernels?

Quoted 7 lines
Quoted 5 lines
Quoted 2 lines

something might trip the fault handler even before probe is called, e.g. some PM handling or simply user accessing that PCIe area using setpci.

If that is the case, it must indeed by done earlier, but still conditional on the presence of the actual PCIe controller.

I am open to suggestions how to do that part.

    if (of_find_matching_node(...))
           do_the_right_stuff();

Gr{oetje,eeting}s,

Geert

Signature · 5 lines
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds
reviewer
#8 lore raw
In reply to Geert Uytterhoeven
Quoted 22 lines · Geert Uytterhoeven

Hi Marek,

Quoted 17 lines · Marek Vasut

On 9/28/20 11:35 AM, Geert Uytterhoeven wrote:
[...]

Quoted 6 lines
Quoted 6 lines
drivers/pci/controller/pcie-rcar-host.c +6 -0
+static int __init rcar_pcie_init(void)
+{
+#ifdef CONFIG_ARM_LPAE
+       hook_fault_code(17, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+                       "asynchronous external abort");
+#else
Quoted 8 lines

drivers/pci/controller/pcie-rcar-host.c static struct platform_driver rcar_pcie_driver = { · line 1112

Quoted 3 lines
drivers/pci/controller/pcie-rcar-host.c +3 -0
+       hook_fault_code(22, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+                       "imprecise external abort");
+#endif

As there can be only a single handler, this may interfere with a handler for another platform in a multi-platform kernel.
Hence I think this should not be done unconditionally, but be moved to the driver's .probe() callback.

Quoted 1 line

Why is nobody doing this in the probe code then ? It seems all the other

Quoted 7 lines

drivers/pci/controller/dwc/pci-keystone.c is:

ks_pcie_probe()

    ks_pcie_add_pcie_port()
      dw_pcie_host_init()
        pp->ops->host_init(pp) = ks_pcie_host_init()
          hook_fault_code()

Looks broken in deferred probe case as hook_fault_code is __init.

Really, hook_fault_code needs to be exported so these drivers can be modules. Or we split out all the abort handlers to a separate broken, aborting PCI hosts module.

Quoted 7 lines
Quoted 1 line

drivers which hook fault code do it in init as well. I can imagine that

Probably nobody bothered exercising the external abort handler on multi-platform kernels?

Quoted 2 lines

something might trip the fault handler even before probe is called, e.g. some PM handling or simply user accessing that PCIe area using setpci.

I don't see how that's possible. You'd first hit translation faults as nothing is mapped.

Quoted 2 lines

If that is the case, it must indeed by done earlier, but still conditional on the presence of the actual PCIe controller.

imx6 should be conditional too.

Rob