rockchip: rk3328: Add support for FriendlyARM NanoPi R2S
Subsystems (2)
PATCH 1/1 rockchip: rk3328: Add support for FriendlyARM NanoPi R2S
This adds support for the NanoPi R2S from FriendlyArm.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LED
--- arch/arm/dts/Makefile | 1 + arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi | 34 +++ arch/arm/dts/rk3328-nanopi-r2s.dts | 317 +++++++++++++++++++++ board/rockchip/evb_rk3328/MAINTAINERS | 7 + configs/nanopi-r2s-rk3328_defconfig | 99 +++++++ 5 files changed, 458 insertions(+) create mode 100644 arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi create mode 100644 arch/arm/dts/rk3328-nanopi-r2s.dts create mode 100644 configs/nanopi-r2s-rk3328_defconfig
arch/arm/dts/Makefile +1 -0
@@ -107,6 +107,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3308) += \ dtb-$(CONFIG_ROCKCHIP_RK3328) += \ rk3328-evb.dtb \ + rk3328-nanopi-r2s.dtb \ rk3328-roc-cc.dtb \ rk3328-rock64.dtb \ rk3328-rock-pi-e.dtb
arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi new file +34 -0
@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2018-2019 Rockchip Electronics Co., Ltd + * (C) Copyright 2020 David Bauer + */ + +#include "rk3328-u-boot.dtsi" +#include "rk3328-sdram-ddr4-666.dtsi" +/ { + chosen { + u-boot,spl-boot-order = "same-as-spl", &sdmmc, &emmc; + }; +}; + +&gpio0 { + u-boot,dm-spl; +}; + +&pinctrl { + u-boot,dm-spl; +}; + +&sdmmc0m1_gpio { + u-boot,dm-spl; +}; + +&pcfg_pull_up_4ma { + u-boot,dm-spl; +}; + +/* Need this and all the pinctrl/gpio stuff above to set pinmux */ +&vcc_sd { + u-boot,dm-spl; +};
arch/arm/dts/rk3328-nanopi-r2s.dts new file +317 -0
317 lines not on this page · raw message
board/rockchip/evb_rk3328/MAINTAINERS +7 -0
@@ -5,6 +5,13 @@ F: board/rockchip/evb_rk3328 F: include/configs/evb_rk3328.h F: configs/evb-rk3328_defconfig +NANOPI-R2S-RK3328 +M: David Bauer <[email protected]> +S: Maintained +F: configs/nanopi-r2s-rk3328_defconfig +F: arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi +F: arch/arm/dts/rk3328-nanopi-r2s.dts + ROC-RK3328-CC M: Loic Devulder <[email protected]> M: Chen-Yu Tsai <[email protected]>
configs/nanopi-r2s-rk3328_defconfig new file +99 -0
99 lines not on this page · raw message
Signature · 1 line
2.27.0
PATCH 1/1 rockchip: rk3328: Add support for FriendlyARM NanoPi R2S
Hi David,
??? Does this board dts available in kernel mainline?
Thanks,
- Kever
Quoted 521 lines · David Bauer
This adds support for the NanoPi R2S from FriendlyArm.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LEDSigned-off-by David Bauer <[email protected]>--- arch/arm/dts/Makefile | 1 + arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi | 34 +++ arch/arm/dts/rk3328-nanopi-r2s.dts | 317 +++++++++++++++++++++ board/rockchip/evb_rk3328/MAINTAINERS | 7 + configs/nanopi-r2s-rk3328_defconfig | 99 +++++++ 5 files changed, 458 insertions(+)create mode 100644
arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsicreate mode 100644arch/arm/dts/rk3328-nanopi-r2s.dtscreate mode 100644 configs/nanopi-r2s-rk3328_defconfigarch/arm/dts/Makefile +1
-0@@ -107,6 +107,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3308) += \ dtb-$(CONFIG_ROCKCHIP_RK3328) += \ rk3328-evb.dtb \ + rk3328-nanopi-r2s.dtb \ rk3328-roc-cc.dtb \ rk3328-rock64.dtb \ rk3328-rock-pi-e.dtbarch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi new file +34
-0@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2018-2019 Rockchip Electronics Co., Ltd + * (C) Copyright 2020 David Bauer + */ + +#include "rk3328-u-boot.dtsi" +#include "rk3328-sdram-ddr4-666.dtsi" +/ { + chosen { + u-boot,spl-boot-order = "same-as-spl", &sdmmc, &emmc; + }; +}; + +&gpio0 { + u-boot,dm-spl; +}; + +&pinctrl { + u-boot,dm-spl; +}; + +&sdmmc0m1_gpio { + u-boot,dm-spl; +}; + +&pcfg_pull_up_4ma { + u-boot,dm-spl; +}; + +/* Need this and all the pinctrl/gpio stuff above to set pinmux */ +&vcc_sd { + u-boot,dm-spl; +};arch/arm/dts/rk3328-nanopi-r2s.dts new file +317
-0@@ -0,0 +1,317 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2020 David Bauer <[email protected]> + */ + +/dts-v1/; + +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include "rk3328.dtsi" + +/ { + model = "FriendlyARM NanoPi R2S"; + compatible = "friendlyarm,nanopi-r2s", "rockchip,rk3328"; + + chosen { + stdout-path = "serial2:1500000n8"; + }; + + gmac_clkin: external-gmac-clock { + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "gmac_clkin"; + #clock-cells = <0>; + }; + + vcc_sd: sdmmc-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc0m1_gpio>; + regulator-name = "vcc_sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_io>; + }; + + vcc_sys: vcc-sys { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + vcc_rtl8153: vcc-rtl8153-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&rtl8153_en_drv>; + regulator-always-on; + regulator-name = "vcc_rtl8153"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&led_pins>; + + sys { + gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>; + label = "nanopi-r2s:red:sys"; + }; + + lan { + gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>; + label = "nanopi-r2s:green:lan"; + }; + + wan { + gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>; + label = "nanopi-r2s:green:wan"; + }; + }; + + gpio_keys { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + pinctrl-names = "default"; + pinctrl-0 = <&button_pins>; + + reset { + label = "Reset Button"; + gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + debounce-interval = <50>; + }; + }; +}; + +&cpu0 { + cpu-supply = <&vdd_arm>; +}; + +&cpu1 { + cpu-supply = <&vdd_arm>; +}; + +&cpu2 { + cpu-supply = <&vdd_arm>; +}; + +&cpu3 { + cpu-supply = <&vdd_arm>; +}; + +&gmac2io { + assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>; + assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>; + clock_in_out = "input"; + phy-supply = <&vcc_io>; + phy-mode = "rgmii"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmiim1_pins>; + snps,force_thresh_dma_mode; + snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 50000>; + tx_delay = <0x24>; + rx_delay = <0x18>; + status = "okay"; +}; + +&i2c1 { + status = "okay"; + + rk805: rk805 at 18 { + compatible = "rockchip,rk805"; + reg = <0x18>; + interrupt-parent = <&gpio2>; + interrupts = <6 IRQ_TYPE_LEVEL_LOW>; + #clock-cells = <1>; + clock-output-names = "xin32k", "rk805-clkout2"; + gpio-controller; + #gpio-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int_l>; + rockchip,system-power-controller; + wakeup-source; + + vcc1-supply = <&vcc_sys>; + vcc2-supply = <&vcc_sys>; + vcc3-supply = <&vcc_sys>; + vcc4-supply = <&vcc_sys>; + vcc5-supply = <&vcc_io>; + vcc6-supply = <&vcc_sys>; + + regulators { + vdd_logic: DCDC_REG1 { + regulator-name = "vdd_logic"; + regulator-min-microvolt = <712500>; + regulator-max-microvolt = <1450000>; + regulator-ramp-delay = <12500>; + regulator-always-on; + regulator-boot-on; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vdd_arm: DCDC_REG2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <712500>; + regulator-max-microvolt = <1450000>; + regulator-ramp-delay = <12500>; + regulator-always-on; + regulator-boot-on; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <950000>; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-name = "vcc_ddr"; + regulator-always-on; + regulator-boot-on; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_io: DCDC_REG4 { + regulator-name = "vcc_io"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_18: LDO_REG1 { + regulator-name = "vcc_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcc18_emmc: LDO_REG2 { + regulator-name = "vcc18_emmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vdd_10: LDO_REG3 { + regulator-name = "vdd_10"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-boot-on; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + }; + }; +}; + +&io_domains { + status = "okay"; + + vccio1-supply = <&vcc_io>; + vccio2-supply = <&vcc18_emmc>; + vccio3-supply = <&vcc_io>; + vccio4-supply = <&vcc_18>; + vccio5-supply = <&vcc_io>; + vccio6-supply = <&vcc_io>; + pmuio-supply = <&vcc_io>; +}; + +&pinctrl { + leds { + led_pins: led_pins { + rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>, + <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>, + <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + button { + button_pins: button_pins { + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pmic { + pmic_int_l: pmic-int-l { + rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + usb { + rtl8153_en_drv: rtl8153-en-drv { + rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&sdmmc { + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + disable-wp; + max-frequency = <150000000>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>; + vmmc-supply = <&vcc_sd>; + status = "okay"; +}; + +&tsadc { + rockchip,hw-tshut-mode = <0>; + rockchip,hw-tshut-polarity = <0>; + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&u2phy { + status = "okay"; + + u2phy_host: host-port { + status = "okay"; + }; +}; + +&usb_host0_ehci { + status = "okay"; +}; + +&usb_host0_ohci { + status = "okay"; +};board/rockchip/evb_rk3328/MAINTAINERS +7
-0@@ -5,6 +5,13 @@ F: board/rockchip/evb_rk3328 F: include/configs/evb_rk3328.h F: configs/evb-rk3328_defconfig +NANOPI-R2S-RK3328 +M: David Bauer <[email protected]> +S: Maintained +F: configs/nanopi-r2s-rk3328_defconfig +F: arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi +F: arch/arm/dts/rk3328-nanopi-r2s.dts + ROC-RK3328-CC M: Loic Devulder <[email protected]> M: Chen-Yu Tsai <[email protected]>configs/nanopi-r2s-rk3328_defconfig new file +99
-0@@ -0,0 +1,99 @@ +CONFIG_ARM=y +CONFIG_ARCH_ROCKCHIP=y +CONFIG_SYS_TEXT_BASE=0x00200000 +CONFIG_SPL_GPIO_SUPPORT=y +CONFIG_ENV_OFFSET=0x3F8000 +CONFIG_ROCKCHIP_RK3328=y +CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y +CONFIG_TPL_LIBCOMMON_SUPPORT=y +CONFIG_TPL_LIBGENERIC_SUPPORT=y +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y +CONFIG_SPL_STACK_R_ADDR=0x600000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_DEBUG_UART_BASE=0xFF130000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SMBIOS_PRODUCT_NAME="nanopi_r2s_rk3328" +CONFIG_DEBUG_UART=y +CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 +# CONFIG_ANDROID_BOOT_IMAGE is not set +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2s.dtb" +CONFIG_MISC_INIT_R=y +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +CONFIG_TPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_STACK_R=y +CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y +CONFIG_SPL_ATF=y +CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y +CONFIG_CMD_BOOTZ=y +CONFIG_CMD_GPT=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_TIME=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_TPL_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2s" +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" +CONFIG_TPL_OF_PLATDATA=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_TPL_DM=y +CONFIG_REGMAP=y +CONFIG_SPL_REGMAP=y +CONFIG_TPL_REGMAP=y +CONFIG_SYSCON=y +CONFIG_SPL_SYSCON=y +CONFIG_TPL_SYSCON=y +CONFIG_CLK=y +CONFIG_SPL_CLK=y +CONFIG_FASTBOOT_BUF_ADDR=0x800800 +CONFIG_FASTBOOT_CMD_OEM_FORMAT=y +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_SF_DEFAULT_SPEED=20000000 +CONFIG_DM_ETH=y +CONFIG_ETH_DESIGNWARE=y +CONFIG_GMAC_ROCKCHIP=y +CONFIG_PINCTRL=y +CONFIG_SPL_PINCTRL=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_RK8XX=y +CONFIG_SPL_DM_REGULATOR=y +CONFIG_REGULATOR_PWM=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_SPL_DM_REGULATOR_FIXED=y +CONFIG_REGULATOR_RK8XX=y +CONFIG_PWM_ROCKCHIP=y +CONFIG_RAM=y +CONFIG_SPL_RAM=y +CONFIG_TPL_RAM=y +CONFIG_DM_RESET=y +CONFIG_BAUDRATE=1500000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYSRESET=y +# CONFIG_TPL_SYSRESET is not set +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_GENERIC=y +CONFIG_USB_DWC2=y +CONFIG_USB_DWC3=y +# CONFIG_USB_DWC3_GADGET is not set +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_DWC2_OTG=y +CONFIG_SPL_TINY_MEMSET=y +CONFIG_TPL_TINY_MEMSET=y +CONFIG_ERRNO_STR=y +CONFIG_SMBIOS_MANUFACTURER="pine64"
PATCH 1/1 rockchip: rk3328: Add support for FriendlyARM NanoPi R2S
Hi Kenver,
Quoted 3 lines · Kever Yang
Hi David,
??? Does this board dts available in kernel mainline?
<Resending as it didn't reach the U-Boot MX>
I'm in the process of mainlining the board to kernel too (planning to submit it within the next week).
The DTS however is identical to the one I'm submitting here. See
https://github.com/blocktrron/linux-nanopi-r2s
Best wishes
David
Quoted 528 lines
Thanks,
- Kever
Quoted 519 lines · David Bauer
This adds support for the NanoPi R2S from FriendlyArm.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LEDSigned-off-by David Bauer <[email protected]>---
? arch/arm/dts/Makefile????????????????????? |?? 1 + ? arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi |? 34 +++ ? arch/arm/dts/rk3328-nanopi-r2s.dts???????? | 317 +++++++++++++++++++++ ? board/rockchip/evb_rk3328/MAINTAINERS????? |?? 7 + ? configs/nanopi-r2s-rk3328_defconfig??????? |? 99 +++++++? 5 files changed, 458 insertions(+)
? create mode 100644arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi? create mode 100644arch/arm/dts/rk3328-nanopi-r2s.dts? create mode 100644 configs/nanopi-r2s-rk3328_defconfigarch/arm/dts/Makefile +1
-0@@ -107,6 +107,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3308) += \ ? ? dtb-$(CONFIG_ROCKCHIP_RK3328) += \ ????? rk3328-evb.dtb \ +??? rk3328-nanopi-r2s.dtb \ ????? rk3328-roc-cc.dtb \ ????? rk3328-rock64.dtb \????? rk3328-rock-pi-e.dtb
arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi new file +34
-0@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2018-2019 Rockchip Electronics Co., Ltd + * (C) Copyright 2020 David Bauer + */ + +#include "rk3328-u-boot.dtsi" +#include "rk3328-sdram-ddr4-666.dtsi" +/ { +??? chosen { +??????? u-boot,spl-boot-order = "same-as-spl", &sdmmc, &emmc; +??? }; +}; + +&gpio0 { +??? u-boot,dm-spl; +}; + +&pinctrl { +??? u-boot,dm-spl; +}; + +&sdmmc0m1_gpio { +??? u-boot,dm-spl; +}; + +&pcfg_pull_up_4ma { +??? u-boot,dm-spl; +}; + +/* Need this and all the pinctrl/gpio stuff above to set pinmux */ +&vcc_sd { +??? u-boot,dm-spl; +};arch/arm/dts/rk3328-nanopi-r2s.dts new file +317
-0@@ -0,0 +1,317 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2020 David Bauer <[email protected]> + */ + +/dts-v1/; + +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include "rk3328.dtsi" + +/ { +??? model = "FriendlyARM NanoPi R2S"; +??? compatible = "friendlyarm,nanopi-r2s", "rockchip,rk3328"; + +??? chosen { +??????? stdout-path = "serial2:1500000n8"; +??? }; + +??? gmac_clkin: external-gmac-clock { +??????? compatible = "fixed-clock"; +??????? clock-frequency = <125000000>; +??????? clock-output-names = "gmac_clkin"; +??????? #clock-cells = <0>; +??? }; + +??? vcc_sd: sdmmc-regulator { +??????? compatible = "regulator-fixed"; +??????? gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>; +??????? pinctrl-names = "default"; +??????? pinctrl-0 = <&sdmmc0m1_gpio>; +??????? regulator-name = "vcc_sd"; +??????? regulator-min-microvolt = <3300000>; +??????? regulator-max-microvolt = <3300000>; +??????? vin-supply = <&vcc_io>; +??? }; + +??? vcc_sys: vcc-sys { +??????? compatible = "regulator-fixed"; +??????? regulator-name = "vcc_sys"; +??????? regulator-always-on; +??????? regulator-boot-on; +??????? regulator-min-microvolt = <5000000>; +??????? regulator-max-microvolt = <5000000>; +??? }; + +??? vcc_rtl8153: vcc-rtl8153-regulator { +??????? compatible = "regulator-fixed"; +??????? gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>; +??????? pinctrl-names = "default"; +??????? pinctrl-0 = <&rtl8153_en_drv>; +??????? regulator-always-on; +??????? regulator-name = "vcc_rtl8153"; +??????? regulator-min-microvolt = <5000000>; +??????? regulator-max-microvolt = <5000000>; +??????? enable-active-high; +??? }; + +??? leds { +??????? compatible = "gpio-leds"; + +??????? pinctrl-names = "default"; +??????? pinctrl-0 = <&led_pins>; + +??????? sys { +??????????? gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>; +??????????? label = "nanopi-r2s:red:sys"; +??????? }; + +??????? lan { +??????????? gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>; +??????????? label = "nanopi-r2s:green:lan"; +??????? }; + +??????? wan { +??????????? gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>; +??????????? label = "nanopi-r2s:green:wan"; +??????? }; +??? }; + +??? gpio_keys { +??????? compatible = "gpio-keys-polled"; +??????? poll-interval = <100>; + +??????? pinctrl-names = "default"; +??????? pinctrl-0 = <&button_pins>; + +??????? reset { +??????????? label = "Reset Button"; +??????????? gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>; +??????????? linux,code = <KEY_RESTART>; +??????????? debounce-interval = <50>; +??????? }; +??? }; +}; + +&cpu0 { +??? cpu-supply = <&vdd_arm>; +}; + +&cpu1 { +??? cpu-supply = <&vdd_arm>; +}; + +&cpu2 { +??? cpu-supply = <&vdd_arm>; +}; + +&cpu3 { +??? cpu-supply = <&vdd_arm>; +}; + +&gmac2io { +??? assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>; +??? assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>; +??? clock_in_out = "input"; +??? phy-supply = <&vcc_io>; +??? phy-mode = "rgmii"; +??? pinctrl-names = "default"; +??? pinctrl-0 = <&rgmiim1_pins>; +??? snps,force_thresh_dma_mode; +??? snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>; +??? snps,reset-active-low; +??? snps,reset-delays-us = <0 10000 50000>; +??? tx_delay = <0x24>; +??? rx_delay = <0x18>; +??? status = "okay"; +}; + +&i2c1 { +??? status = "okay"; + +??? rk805: rk805 at 18 { +??????? compatible = "rockchip,rk805"; +??????? reg = <0x18>; +??????? interrupt-parent = <&gpio2>; +??????? interrupts = <6 IRQ_TYPE_LEVEL_LOW>; +??????? #clock-cells = <1>; +??????? clock-output-names = "xin32k", "rk805-clkout2"; +??????? gpio-controller; +??????? #gpio-cells = <2>; +??????? pinctrl-names = "default"; +??????? pinctrl-0 = <&pmic_int_l>; +??????? rockchip,system-power-controller; +??????? wakeup-source; + +??????? vcc1-supply = <&vcc_sys>; +??????? vcc2-supply = <&vcc_sys>; +??????? vcc3-supply = <&vcc_sys>; +??????? vcc4-supply = <&vcc_sys>; +??????? vcc5-supply = <&vcc_io>; +??????? vcc6-supply = <&vcc_sys>; + +??????? regulators { +??????????? vdd_logic: DCDC_REG1 { +??????????????? regulator-name = "vdd_logic"; +??????????????? regulator-min-microvolt = <712500>; +??????????????? regulator-max-microvolt = <1450000>; +??????????????? regulator-ramp-delay = <12500>; +??????????????? regulator-always-on; +??????????????? regulator-boot-on; +??????????????? regulator-state-mem { +??????????????????? regulator-on-in-suspend; +??????????????????? regulator-suspend-microvolt = <1000000>; +??????????????? }; +??????????? }; + +??????????? vdd_arm: DCDC_REG2 { +??????????????? regulator-name = "vdd_arm"; +??????????????? regulator-min-microvolt = <712500>; +??????????????? regulator-max-microvolt = <1450000>; +??????????????? regulator-ramp-delay = <12500>; +??????????????? regulator-always-on; +??????????????? regulator-boot-on; +??????????????? regulator-state-mem { +??????????????????? regulator-on-in-suspend; +??????????????????? regulator-suspend-microvolt = <950000>; +??????????????? }; +??????????? }; + +??????????? vcc_ddr: DCDC_REG3 { +??????????????? regulator-name = "vcc_ddr"; +??????????????? regulator-always-on; +??????????????? regulator-boot-on; +??????????????? regulator-state-mem { +??????????????????? regulator-on-in-suspend; +??????????????? }; +??????????? }; + +??????????? vcc_io: DCDC_REG4 { +??????????????? regulator-name = "vcc_io"; +??????????????? regulator-min-microvolt = <3300000>; +??????????????? regulator-max-microvolt = <3300000>; +??????????????? regulator-always-on; +??????????????? regulator-boot-on; +??????????????? regulator-state-mem { +??????????????????? regulator-on-in-suspend; +??????????????????? regulator-suspend-microvolt = <3300000>; +??????????????? }; +??????????? }; + +??????????? vcc_18: LDO_REG1 { +??????????????? regulator-name = "vcc_18"; +??????????????? regulator-min-microvolt = <1800000>; +??????????????? regulator-max-microvolt = <1800000>; +??????????????? regulator-always-on; +??????????????? regulator-boot-on; +??????????????? regulator-state-mem { +??????????????????? regulator-on-in-suspend; +??????????????????? regulator-suspend-microvolt = <1800000>; +??????????????? }; +??????????? }; + +??????????? vcc18_emmc: LDO_REG2 { +??????????????? regulator-name = "vcc18_emmc"; +??????????????? regulator-min-microvolt = <1800000>; +??????????????? regulator-max-microvolt = <1800000>; +??????????????? regulator-always-on; +??????????????? regulator-boot-on; +??????????????? regulator-state-mem { +??????????????????? regulator-on-in-suspend; +??????????????????? regulator-suspend-microvolt = <1800000>; +??????????????? }; +??????????? }; + +??????????? vdd_10: LDO_REG3 { +??????????????? regulator-name = "vdd_10"; +??????????????? regulator-min-microvolt = <1000000>; +??????????????? regulator-max-microvolt = <1000000>; +??????????????? regulator-always-on; +??????????????? regulator-boot-on; +??????????????? regulator-state-mem { +??????????????????? regulator-on-in-suspend; +??????????????????? regulator-suspend-microvolt = <1000000>; +??????????????? }; +??????????? }; +??????? }; +??? }; +}; + +&io_domains { +??? status = "okay"; + +??? vccio1-supply = <&vcc_io>; +??? vccio2-supply = <&vcc18_emmc>; +??? vccio3-supply = <&vcc_io>; +??? vccio4-supply = <&vcc_18>; +??? vccio5-supply = <&vcc_io>; +??? vccio6-supply = <&vcc_io>; +??? pmuio-supply = <&vcc_io>; +}; + +&pinctrl { +??? leds { +??????? led_pins: led_pins { +??????????? rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>, +??????????????????????????? <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>, +??????????????????????????? <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>; +??????? }; +??? }; + +??? button { +??????? button_pins: button_pins { +??????????? rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>; +??????? }; +??? }; + +??? pmic { +??????? pmic_int_l: pmic-int-l { +??????????? rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>; +??????? }; +??? }; + +??? usb { +??????? rtl8153_en_drv: rtl8153-en-drv { +??????????? rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; +??????? }; +??? }; +}; + +&sdmmc { +??? bus-width = <4>; +??? cap-mmc-highspeed; +??? cap-sd-highspeed; +??? disable-wp; +??? max-frequency = <150000000>; +??? pinctrl-names = "default"; +??? pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>; +??? vmmc-supply = <&vcc_sd>; +??? status = "okay"; +}; + +&tsadc { +??? rockchip,hw-tshut-mode = <0>; +??? rockchip,hw-tshut-polarity = <0>; +??? status = "okay"; +}; + +&uart2 { +??? status = "okay"; +}; + +&u2phy { +??? status = "okay"; + +??? u2phy_host: host-port { +??????? status = "okay"; +??? }; +}; + +&usb_host0_ehci { +??? status = "okay"; +}; + +&usb_host0_ohci { +??? status = "okay"; +};board/rockchip/evb_rk3328/MAINTAINERS +0
-0@@ -5,6 +5,13 @@ F:????? board/rockchip/evb_rk3328? F:?????
include/configs/evb_rk3328.h
? F:????? configs/evb-rk3328_defconfig
? +NANOPI-R2S-RK3328board/rockchip/evb_rk3328/MAINTAINERS +6
-0+M:????? David Bauer <[email protected]> +S:????? Maintained +F:????? configs/nanopi-r2s-rk3328_defconfig +F:????? arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi +F:????? arch/arm/dts/rk3328-nanopi-r2s.dts +? ROC-RK3328-CC
? M:????? Loic Devulder <[email protected]>
? M:????? Chen-Yu Tsai <[email protected]>configs/nanopi-r2s-rk3328_defconfig new file +99
-0@@ -0,0 +1,99 @@ +CONFIG_ARM=y +CONFIG_ARCH_ROCKCHIP=y +CONFIG_SYS_TEXT_BASE=0x00200000 +CONFIG_SPL_GPIO_SUPPORT=y +CONFIG_ENV_OFFSET=0x3F8000 +CONFIG_ROCKCHIP_RK3328=y +CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y +CONFIG_TPL_LIBCOMMON_SUPPORT=y +CONFIG_TPL_LIBGENERIC_SUPPORT=y +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y +CONFIG_SPL_STACK_R_ADDR=0x600000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_DEBUG_UART_BASE=0xFF130000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SMBIOS_PRODUCT_NAME="nanopi_r2s_rk3328" +CONFIG_DEBUG_UART=y +CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 +# CONFIG_ANDROID_BOOT_IMAGE is not set +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2s.dtb" +CONFIG_MISC_INIT_R=y +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +CONFIG_TPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_STACK_R=y +CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y +CONFIG_SPL_ATF=y +CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y +CONFIG_CMD_BOOTZ=y +CONFIG_CMD_GPT=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_TIME=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_TPL_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2s" +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" +CONFIG_TPL_OF_PLATDATA=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_TPL_DM=y +CONFIG_REGMAP=y +CONFIG_SPL_REGMAP=y +CONFIG_TPL_REGMAP=y +CONFIG_SYSCON=y +CONFIG_SPL_SYSCON=y +CONFIG_TPL_SYSCON=y +CONFIG_CLK=y +CONFIG_SPL_CLK=y +CONFIG_FASTBOOT_BUF_ADDR=0x800800 +CONFIG_FASTBOOT_CMD_OEM_FORMAT=y +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_SF_DEFAULT_SPEED=20000000 +CONFIG_DM_ETH=y +CONFIG_ETH_DESIGNWARE=y +CONFIG_GMAC_ROCKCHIP=y +CONFIG_PINCTRL=y +CONFIG_SPL_PINCTRL=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_RK8XX=y +CONFIG_SPL_DM_REGULATOR=y +CONFIG_REGULATOR_PWM=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_SPL_DM_REGULATOR_FIXED=y +CONFIG_REGULATOR_RK8XX=y +CONFIG_PWM_ROCKCHIP=y +CONFIG_RAM=y +CONFIG_SPL_RAM=y +CONFIG_TPL_RAM=y +CONFIG_DM_RESET=y +CONFIG_BAUDRATE=1500000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYSRESET=y +# CONFIG_TPL_SYSRESET is not set +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_GENERIC=y +CONFIG_USB_DWC2=y +CONFIG_USB_DWC3=y +# CONFIG_USB_DWC3_GADGET is not set +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_DWC2_OTG=y +CONFIG_SPL_TINY_MEMSET=y +CONFIG_TPL_TINY_MEMSET=y +CONFIG_ERRNO_STR=y +CONFIG_SMBIOS_MANUFACTURER="pine64"
A message that is not in the archive (sent off-list or not yet received): [email protected]
PATCH 1/1 rockchip: rk3328: Add support for FriendlyARM NanoPi R2S
Hi David,
??? You can send new version patch when with commit id in the mainline
kernel when it's available.
Thanks,
- Kever
? 2020/7/22 ??4:33, David Bauer ??:
Quoted 542 lines
Hi Kever,
Quoted 3 lines · Kever Yang
Hi David,
??? Does this board dts available in kernel mainline?
I'm in the process of mainlining the board to kernel too (planning to submit it within the next week).
The DTS however is identical to the one I'm submitting here. See
https://github.com/blocktrron/linux-nanopi-r2sBest wishes
DavidQuoted 526 lines
Thanks,
- Kever
Quoted 519 lines · David Bauer
This adds support for the NanoPi R2S from FriendlyArm.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LEDSigned-off-by David Bauer <[email protected]>---
? arch/arm/dts/Makefile????????????????????? |?? 1 + ? arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi |? 34 +++ ? arch/arm/dts/rk3328-nanopi-r2s.dts???????? | 317 +++++++++++++++++++++ ? board/rockchip/evb_rk3328/MAINTAINERS????? |?? 7 + ? configs/nanopi-r2s-rk3328_defconfig??????? |? 99 +++++++? 5 files changed, 458 insertions(+)
? create mode 100644arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi? create mode 100644arch/arm/dts/rk3328-nanopi-r2s.dts? create mode 100644 configs/nanopi-r2s-rk3328_defconfigarch/arm/dts/Makefile +1
-0@@ -107,6 +107,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3308) += \ ? ? dtb-$(CONFIG_ROCKCHIP_RK3328) += \ ????? rk3328-evb.dtb \ +??? rk3328-nanopi-r2s.dtb \ ????? rk3328-roc-cc.dtb \ ????? rk3328-rock64.dtb \ ????? rk3328-rock-pi-e.dtbarch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi new file +34
-0@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2018-2019 Rockchip Electronics Co., Ltd + * (C) Copyright 2020 David Bauer + */ + +#include "rk3328-u-boot.dtsi" +#include "rk3328-sdram-ddr4-666.dtsi" +/ { +??? chosen { +??????? u-boot,spl-boot-order = "same-as-spl", &sdmmc, &emmc; +??? }; +}; + +&gpio0 { +??? u-boot,dm-spl; +}; + +&pinctrl { +??? u-boot,dm-spl; +}; + +&sdmmc0m1_gpio { +??? u-boot,dm-spl; +}; + +&pcfg_pull_up_4ma { +??? u-boot,dm-spl; +}; + +/* Need this and all the pinctrl/gpio stuff above to set pinmux */ +&vcc_sd { +??? u-boot,dm-spl; +};arch/arm/dts/rk3328-nanopi-r2s.dts new file +317
-0@@ -0,0 +1,317 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2020 David Bauer <[email protected]> + */ + +/dts-v1/; + +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include "rk3328.dtsi" + +/ { +??? model = "FriendlyARM NanoPi R2S"; +??? compatible = "friendlyarm,nanopi-r2s", "rockchip,rk3328"; + +??? chosen { +??????? stdout-path = "serial2:1500000n8"; +??? }; + +??? gmac_clkin: external-gmac-clock { +??????? compatible = "fixed-clock"; +??????? clock-frequency = <125000000>; +??????? clock-output-names = "gmac_clkin"; +??????? #clock-cells = <0>; +??? }; + +??? vcc_sd: sdmmc-regulator { +??????? compatible = "regulator-fixed"; +??????? gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>; +??????? pinctrl-names = "default"; +??????? pinctrl-0 = <&sdmmc0m1_gpio>; +??????? regulator-name = "vcc_sd"; +??????? regulator-min-microvolt = <3300000>; +??????? regulator-max-microvolt = <3300000>; +??????? vin-supply = <&vcc_io>; +??? }; + +??? vcc_sys: vcc-sys { +??????? compatible = "regulator-fixed"; +??????? regulator-name = "vcc_sys"; +??????? regulator-always-on; +??????? regulator-boot-on; +??????? regulator-min-microvolt = <5000000>; +??????? regulator-max-microvolt = <5000000>; +??? }; + +??? vcc_rtl8153: vcc-rtl8153-regulator { +??????? compatible = "regulator-fixed"; +??????? gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>; +??????? pinctrl-names = "default"; +??????? pinctrl-0 = <&rtl8153_en_drv>; +??????? regulator-always-on; +??????? regulator-name = "vcc_rtl8153"; +??????? regulator-min-microvolt = <5000000>; +??????? regulator-max-microvolt = <5000000>; +??????? enable-active-high; +??? }; + +??? leds { +??????? compatible = "gpio-leds"; + +??????? pinctrl-names = "default"; +??????? pinctrl-0 = <&led_pins>; + +??????? sys { +??????????? gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>; +??????????? label = "nanopi-r2s:red:sys"; +??????? }; + +??????? lan { +??????????? gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>; +??????????? label = "nanopi-r2s:green:lan"; +??????? }; + +??????? wan { +??????????? gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>; +??????????? label = "nanopi-r2s:green:wan"; +??????? }; +??? }; + +??? gpio_keys { +??????? compatible = "gpio-keys-polled"; +??????? poll-interval = <100>; + +??????? pinctrl-names = "default"; +??????? pinctrl-0 = <&button_pins>; + +??????? reset { +??????????? label = "Reset Button"; +??????????? gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>; +??????????? linux,code = <KEY_RESTART>; +??????????? debounce-interval = <50>; +??????? }; +??? }; +}; + +&cpu0 { +??? cpu-supply = <&vdd_arm>; +}; + +&cpu1 { +??? cpu-supply = <&vdd_arm>; +}; + +&cpu2 { +??? cpu-supply = <&vdd_arm>; +}; + +&cpu3 { +??? cpu-supply = <&vdd_arm>; +}; + +&gmac2io { +??? assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>; +??? assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>; +??? clock_in_out = "input"; +??? phy-supply = <&vcc_io>; +??? phy-mode = "rgmii"; +??? pinctrl-names = "default"; +??? pinctrl-0 = <&rgmiim1_pins>; +??? snps,force_thresh_dma_mode; +??? snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>; +??? snps,reset-active-low; +??? snps,reset-delays-us = <0 10000 50000>; +??? tx_delay = <0x24>; +??? rx_delay = <0x18>; +??? status = "okay"; +}; + +&i2c1 { +??? status = "okay"; + +??? rk805: rk805 at 18 { +??????? compatible = "rockchip,rk805"; +??????? reg = <0x18>; +??????? interrupt-parent = <&gpio2>; +??????? interrupts = <6 IRQ_TYPE_LEVEL_LOW>; +??????? #clock-cells = <1>; +??????? clock-output-names = "xin32k", "rk805-clkout2"; +??????? gpio-controller; +??????? #gpio-cells = <2>; +??????? pinctrl-names = "default"; +??????? pinctrl-0 = <&pmic_int_l>; +??????? rockchip,system-power-controller; +??????? wakeup-source; + +??????? vcc1-supply = <&vcc_sys>; +??????? vcc2-supply = <&vcc_sys>; +??????? vcc3-supply = <&vcc_sys>; +??????? vcc4-supply = <&vcc_sys>; +??????? vcc5-supply = <&vcc_io>; +??????? vcc6-supply = <&vcc_sys>; + +??????? regulators { +??????????? vdd_logic: DCDC_REG1 { +??????????????? regulator-name = "vdd_logic"; +??????????????? regulator-min-microvolt = <712500>; +??????????????? regulator-max-microvolt = <1450000>; +??????????????? regulator-ramp-delay = <12500>; +??????????????? regulator-always-on; +??????????????? regulator-boot-on; +??????????????? regulator-state-mem { +??????????????????? regulator-on-in-suspend; +??????????????????? regulator-suspend-microvolt = <1000000>; +??????????????? }; +??????????? }; + +??????????? vdd_arm: DCDC_REG2 { +??????????????? regulator-name = "vdd_arm"; +??????????????? regulator-min-microvolt = <712500>; +??????????????? regulator-max-microvolt = <1450000>; +??????????????? regulator-ramp-delay = <12500>; +??????????????? regulator-always-on; +??????????????? regulator-boot-on; +??????????????? regulator-state-mem { +??????????????????? regulator-on-in-suspend; +??????????????????? regulator-suspend-microvolt = <950000>; +??????????????? }; +??????????? }; + +??????????? vcc_ddr: DCDC_REG3 { +??????????????? regulator-name = "vcc_ddr"; +??????????????? regulator-always-on; +??????????????? regulator-boot-on; +??????????????? regulator-state-mem { +??????????????????? regulator-on-in-suspend; +??????????????? }; +??????????? }; + +??????????? vcc_io: DCDC_REG4 { +??????????????? regulator-name = "vcc_io"; +??????????????? regulator-min-microvolt = <3300000>; +??????????????? regulator-max-microvolt = <3300000>; +??????????????? regulator-always-on; +??????????????? regulator-boot-on; +??????????????? regulator-state-mem { +??????????????????? regulator-on-in-suspend; +??????????????????? regulator-suspend-microvolt = <3300000>; +??????????????? }; +??????????? }; + +??????????? vcc_18: LDO_REG1 { +??????????????? regulator-name = "vcc_18"; +??????????????? regulator-min-microvolt = <1800000>; +??????????????? regulator-max-microvolt = <1800000>; +??????????????? regulator-always-on; +??????????????? regulator-boot-on; +??????????????? regulator-state-mem { +??????????????????? regulator-on-in-suspend; +??????????????????? regulator-suspend-microvolt = <1800000>; +??????????????? }; +??????????? }; + +??????????? vcc18_emmc: LDO_REG2 { +??????????????? regulator-name = "vcc18_emmc"; +??????????????? regulator-min-microvolt = <1800000>; +??????????????? regulator-max-microvolt = <1800000>; +??????????????? regulator-always-on; +??????????????? regulator-boot-on; +??????????????? regulator-state-mem { +??????????????????? regulator-on-in-suspend; +??????????????????? regulator-suspend-microvolt = <1800000>; +??????????????? }; +??????????? }; + +??????????? vdd_10: LDO_REG3 { +??????????????? regulator-name = "vdd_10"; +??????????????? regulator-min-microvolt = <1000000>; +??????????????? regulator-max-microvolt = <1000000>; +??????????????? regulator-always-on; +??????????????? regulator-boot-on; +??????????????? regulator-state-mem { +??????????????????? regulator-on-in-suspend; +??????????????????? regulator-suspend-microvolt = <1000000>; +??????????????? }; +??????????? }; +??????? }; +??? }; +}; + +&io_domains { +??? status = "okay"; + +??? vccio1-supply = <&vcc_io>; +??? vccio2-supply = <&vcc18_emmc>; +??? vccio3-supply = <&vcc_io>; +??? vccio4-supply = <&vcc_18>; +??? vccio5-supply = <&vcc_io>; +??? vccio6-supply = <&vcc_io>; +??? pmuio-supply = <&vcc_io>; +}; + +&pinctrl { +??? leds { +??????? led_pins: led_pins { +??????????? rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>, +??????????????????????????? <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>, +??????????????????????????? <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>; +??????? }; +??? }; + +??? button { +??????? button_pins: button_pins { +??????????? rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>; +??????? }; +??? }; + +??? pmic { +??????? pmic_int_l: pmic-int-l { +??????????? rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>; +??????? }; +??? }; + +??? usb { +??????? rtl8153_en_drv: rtl8153-en-drv { +??????????? rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; +??????? }; +??? }; +}; + +&sdmmc { +??? bus-width = <4>; +??? cap-mmc-highspeed; +??? cap-sd-highspeed; +??? disable-wp; +??? max-frequency = <150000000>; +??? pinctrl-names = "default"; +??? pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>; +??? vmmc-supply = <&vcc_sd>; +??? status = "okay"; +}; + +&tsadc { +??? rockchip,hw-tshut-mode = <0>; +??? rockchip,hw-tshut-polarity = <0>; +??? status = "okay"; +}; + +&uart2 { +??? status = "okay"; +}; + +&u2phy { +??? status = "okay"; + +??? u2phy_host: host-port { +??????? status = "okay"; +??? }; +}; + +&usb_host0_ehci { +??? status = "okay"; +}; + +&usb_host0_ohci { +??? status = "okay"; +};board/rockchip/evb_rk3328/MAINTAINERS +6
-0@@ -5,6 +5,13 @@ F:????? board/rockchip/evb_rk3328 ? F:????? include/configs/evb_rk3328.h ? F:????? configs/evb-rk3328_defconfig ? +NANOPI-R2S-RK3328 +M:????? David Bauer <[email protected]> +S:????? Maintained +F:????? configs/nanopi-r2s-rk3328_defconfig +F:????? arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi +F:????? arch/arm/dts/rk3328-nanopi-r2s.dts + ? ROC-RK3328-CC ? M:????? Loic Devulder <[email protected]> ? M:????? Chen-Yu Tsai <[email protected]>configs/nanopi-r2s-rk3328_defconfig new file +99
-0@@ -0,0 +1,99 @@ +CONFIG_ARM=y +CONFIG_ARCH_ROCKCHIP=y +CONFIG_SYS_TEXT_BASE=0x00200000 +CONFIG_SPL_GPIO_SUPPORT=y +CONFIG_ENV_OFFSET=0x3F8000 +CONFIG_ROCKCHIP_RK3328=y +CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y +CONFIG_TPL_LIBCOMMON_SUPPORT=y +CONFIG_TPL_LIBGENERIC_SUPPORT=y +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y +CONFIG_SPL_STACK_R_ADDR=0x600000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_DEBUG_UART_BASE=0xFF130000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SMBIOS_PRODUCT_NAME="nanopi_r2s_rk3328" +CONFIG_DEBUG_UART=y +CONFIG_TPL_SYS_MALLOC_F_LEN=0x800 +# CONFIG_ANDROID_BOOT_IMAGE is not set +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-nanopi-r2s.dtb" +CONFIG_MISC_INIT_R=y +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +CONFIG_TPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_STACK_R=y +CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y +CONFIG_SPL_ATF=y +CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y +CONFIG_CMD_BOOTZ=y +CONFIG_CMD_GPT=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_TIME=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_TPL_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="rk3328-nanopi-r2s" +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" +CONFIG_TPL_OF_PLATDATA=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_TPL_DM=y +CONFIG_REGMAP=y +CONFIG_SPL_REGMAP=y +CONFIG_TPL_REGMAP=y +CONFIG_SYSCON=y +CONFIG_SPL_SYSCON=y +CONFIG_TPL_SYSCON=y +CONFIG_CLK=y +CONFIG_SPL_CLK=y +CONFIG_FASTBOOT_BUF_ADDR=0x800800 +CONFIG_FASTBOOT_CMD_OEM_FORMAT=y +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_SF_DEFAULT_SPEED=20000000 +CONFIG_DM_ETH=y +CONFIG_ETH_DESIGNWARE=y +CONFIG_GMAC_ROCKCHIP=y +CONFIG_PINCTRL=y +CONFIG_SPL_PINCTRL=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_RK8XX=y +CONFIG_SPL_DM_REGULATOR=y +CONFIG_REGULATOR_PWM=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_SPL_DM_REGULATOR_FIXED=y +CONFIG_REGULATOR_RK8XX=y +CONFIG_PWM_ROCKCHIP=y +CONFIG_RAM=y +CONFIG_SPL_RAM=y +CONFIG_TPL_RAM=y +CONFIG_DM_RESET=y +CONFIG_BAUDRATE=1500000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYSRESET=y +# CONFIG_TPL_SYSRESET is not set +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_GENERIC=y +CONFIG_USB_DWC2=y +CONFIG_USB_DWC3=y +# CONFIG_USB_DWC3_GADGET is not set +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_DWC2_OTG=y +CONFIG_SPL_TINY_MEMSET=y +CONFIG_TPL_TINY_MEMSET=y +CONFIG_ERRNO_STR=y +CONFIG_SMBIOS_MANUFACTURER="pine64"