USB (OHCI) not working without pci=routeirq
Subsystems (2)
Bjorn, Linux kernel devs,
when booting with a recent kernel (2.6.9-rc2-mm2), usb_ohci fails to initialize the USB bus and no USB device will work at that point. Adding pci=routeirq fixed the problem.
I believe this has been working with earlier kernels, but I don't use USB often enough to remember.
The PC is an Compaq (HP) Presario 2100Z notebook.
Here's a diff of the dmesg output of two boots with and without pci=routeirq:
dmesg +18 -8
@@ -22,10 +22,10 @@ ACPI: DSDT (v001 ATI U1_M1535 0x06040000 MSFT 0x0100000d) @ 0x00000000 Built 1 zonelists Initializing CPU#0 -Kernel command line: BOOT_IMAGE=Gentoo ro root=305 elevator=cfq +Kernel command line: BOOT_IMAGE=Gentoo ro root=305 elevator=cfq pci=routeirq CPU 0 irqstacks, hard=c04df000 soft=c04de000 PID hash table entries: 2048 (order: 11, 32768 bytes) -Detected 1788.828 MHz processor. +Detected 1789.260 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
@@ -72,18 +72,28 @@ usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing -** PCI interrupts are no longer routed automatically. If this -** causes a device to stop working, it is probably because the -** driver failed to call pci_enable_device(). As a temporary -** workaround, the "pci=routeirq" argument restores the old -** behavior. If this argument makes the device work again, +** Routing PCI interrupts for all devices because "pci=routeirq" +** was specified. If this was required to make a driver work, ** please email the output of "lspci" to [email protected] ** so I can fix the driver. +ACPI: PCI Interrupt Link [LNKU] enabled at IRQ 10 +ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 10 (level, low) -> IRQ 10 +ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5 +ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 5 (level, low) -> IRQ 5 +ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 3 +ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 3 (level, low) -> IRQ 3 +ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11 +ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 11 (level, low) -> IRQ 11 +ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 +ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 10 (level, low) -> IRQ 10 +ACPI: PCI interrupt 0000:00:10.0[A]: no GSI +ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 +ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 11 (level, low) -> IRQ 11 +ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 10 (level, low) -> IRQ 10 Simple Boot Flag at 0x36 set to 0x1 Machine check exception polling timer started. ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb. Activating ISA DMA hang workarounds. -ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 10 (level, low) -> IRQ 10 radeonfb: Retreived PLL infos from BIOS radeonfb: Reference=191.86 MHz (RefDiv=426) Memory=160.00 Mhz,
System=133.00 MHz
@@ -114,7 +124,6 @@
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
-ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 3
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 3 (level, low) -> IRQ 3 ttyS1 at I/O 0x8828 (irq = 3) is a 8250
ttyS2 at I/O 0x8840 (irq = 3) is a 8250
@@ -128,7 +137,6 @@
originally by Donald Becker <[email protected]>
http://www.scyld.com/network/natsemi.html
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
-ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 11 (level, low) -> IRQ 11 natsemi eth0: NatSemi DP8381[56] at 0xdc838000 (0000:00:12.0),
00:0d:9d:5a:41:46, IRQ 11, port TP.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
@@ -162,17 +170,12 @@
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA Uniform CD-ROM driver Revision: 3.20
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
-ACPI: PCI Interrupt Link [LNKU] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 10 (level, low) -> IRQ 10 ohci_hcd 0000:00:02.0: ALi Corporation USB 1.1 Controller ohci_hcd 0000:00:02.0: irq 10, pci mem 0xd0004000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
-ohci_hcd 0000:00:02.0: init err (00002edf 2a2f)
-ohci_hcd 0000:00:02.0: can't start
-ohci_hcd 0000:00:02.0: init error -75
-ohci_hcd 0000:00:02.0: remove, state 0
-ohci_hcd 0000:00:02.0: USB bus 1 deregistered
-ohci_hcd: probe of 0000:00:02.0 failed with error -75
+hub 1-0:1.0: USB hub found
+hub 1-0:1.0: 4 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
@@ -180,6 +183,8 @@
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
+usb 1-2: new low speed USB device using address 2
+input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:02.0-2
Synaptics Touchpad, model: 1
Firmware: 5.9
Sensor: 35
@@ -189,7 +194,6 @@
-> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
Advanced Linux Sound Architecture Driver Version 1.0.6 (Sun Aug 15
07:17:53 2004 UTC).
-ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 5 (level, low) -> IRQ 5 ALSA device list:
#0: ALI 5451 at 0x8400, irq 5
@@ -216,10 +220,9 @@
Adding 1004052k swap on /dev/hda3. Priority:-1 extents:1 Linux Kernel Card Services
options: [pci] [cardbus] [pm]
-ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:0a.0 [0000:0000]
-Yenta: ISA IRQ mask 0x0498, PCI irq 11
+Yenta: ISA IRQ mask 0x0098, PCI irq 11
Socket status: 30000007
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
lspci:
0000:00:00.0 Host bridge: ATI Technologies Inc AGP Bridge [IGP 320M] (rev 13) 0000:00:01.0 PCI bridge: ATI Technologies Inc PCI Bridge [IGP 320M] (rev 01) 0000:00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) 0000:00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 02)
0000:00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV] 0000:00:08.0 Modem: ALi Corporation M5457 AC'97 Modem Controller 0000:00:0a.0 CardBus bridge: O2 Micro, Inc. OZ6912 Cardbus Controller 0000:00:0c.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link)
0000:00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c4) 0000:00:11.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU] 0000:00:12.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller
0000:01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility U1
Let me know if you require any additional information.
Cheers,
Andre
Quoted 8 lines · Andre Eisenbach
when booting with a recent kernel (2.6.9-rc2-mm2),
usb_ohcifails to initialize the USB bus and no USB device will work at that point. Adding pci=routeirq fixed the problem.I believe this has been working with earlier kernels, but I don't use USB often enough to remember.
The PC is an Compaq (HP) Presario 2100Z notebook.
As far as I can see, usb_hcd_pci_probe() is using pci_enable_device() correctly, so "pci=routeirq" shouldn't make a difference. However, I do see a similar ohci_hcd initialization failure on my DL360 (my failure occurs both with and without "pci=routeirq").
My device worked correctly on 2.6.9-rc1-mm4 and is broken in 2.6.9-rc2-mm1.
My errors look like this:
ACPI: PCI interrupt 0000:00:0f.2[A] -> GSI 10 (level, low) -> IRQ 10 ohci_hcd 0000:00:0f.2: ServerWorks OSB4/CSB5 OHCI USB Controller ohci_hcd 0000:00:0f.2: irq 10, pci mem 0xf5e70000 ohci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:0f.2: init err (00002edf 0000)
ohci_hcd 0000:00:0f.2: can't start
ohci_hcd 0000:00:0f.2: init error -75
ohci_hcd 0000:00:0f.2: remove, state 0
ohci_hcd 0000:00:0f.2: USB bus 1 deregistered
ohci_hcd: probe of 0000:00:0f.2 failed with error -75
Quoted 145 lines
Here's a diff of the dmesg output of two boots with and without pci=routeirq:
dmesg 2004-09-23 10:07:34.000000000 -0700 renamed from dmesg 2004-09-23 10:09:57.615512000 -0700 +18
-8@@ -22,10 +22,10 @@ ACPI: DSDT (v001 ATI U1_M1535 0x06040000 MSFT 0x0100000d) @ 0x00000000 Built 1 zonelists Initializing CPU#0 -Kernel command line: BOOT_IMAGE=Gentoo ro root=305 elevator=cfq +Kernel command line: BOOT_IMAGE=Gentoo ro root=305 elevator=cfq pci=routeirq CPU 0 irqstacks, hard=c04df000 soft=c04de000 PID hash table entries: 2048 (order: 11, 32768 bytes) -Detected 1788.828 MHz processor. +Detected 1789.260 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)@@ -72,18 +72,28 @@ usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing -** PCI interrupts are no longer routed automatically. If this -** causes a device to stop working, it is probably because the -** driver failed to call pci_enable_device(). As a temporary -** workaround, the "pci=routeirq" argument restores the old -** behavior. If this argument makes the device work again, +** Routing PCI interrupts for all devices because "pci=routeirq" +** was specified. If this was required to make a driver work, ** please email the output of "lspci" to [email protected] ** so I can fix the driver. +ACPI: PCI Interrupt Link [LNKU] enabled at IRQ 10 +ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 10 (level, low) -> IRQ 10 +ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5 +ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 5 (level, low) -> IRQ 5 +ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 3 +ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 3 (level, low) -> IRQ 3 +ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11 +ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 11 (level, low) -> IRQ 11 +ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 +ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 10 (level, low) -> IRQ 10 +ACPI: PCI interrupt 0000:00:10.0[A]: no GSI +ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 +ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 11 (level, low) -> IRQ 11 +ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 10 (level, low) -> IRQ 10 Simple Boot Flag at 0x36 set to 0x1 Machine check exception polling timer started. ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb. Activating ISA DMA hang workarounds. -ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 10 (level, low) -> IRQ 10 radeonfb: Retreived PLL infos from BIOS radeonfb: Reference=191.86 MHz (RefDiv=426) Memory=160.00 Mhz,System=133.00 MHz
dmesg 2004-09-23 10:07:34.000000000 -0700 renamed from dmesg 2004-09-23 10:09:57.615512000 -0700 +0
-2@@ -114,7 +124,6 @@ serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A -ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 3 ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 3 (level, low) -> IRQ 3 ttyS1 at I/O 0x8828 (irq = 3) is a 8250 ttyS2 at I/O 0x8840 (irq = 3) is a 8250@@ -128,7 +137,6 @@ originally by Donald Becker <[email protected]> http://www.scyld.com/network/natsemi.html 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder -ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 11 (level, low) -> IRQ 11 natsemi eth0: NatSemi DP8381[56] at 0xdc838000 (0000:00:12.0),00:0d:9d:5a:41:46, IRQ 11, port TP.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2dmesg 2004-09-23 10:07:34.000000000 -0700 renamed from dmesg 2004-09-23 10:09:57.615512000 -0700 +4
-7@@ -162,17 +170,12 @@ hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) -ACPI: PCI Interrupt Link [LNKU] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 10 (level, low) -> IRQ 10 ohci_hcd 0000:00:02.0: ALi Corporation USB 1.1 Controller ohci_hcd 0000:00:02.0: irq 10, pci mem 0xd0004000 ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 -ohci_hcd 0000:00:02.0: init err (00002edf 2a2f) -ohci_hcd 0000:00:02.0: can't start -ohci_hcd 0000:00:02.0: init error -75 -ohci_hcd 0000:00:02.0: remove, state 0 -ohci_hcd 0000:00:02.0: USB bus 1 deregistered -ohci_hcd: probe of 0000:00:02.0 failed with error -75 +hub 1-0:1.0: USB hub found +hub 1-0:1.0: 4 ports detected Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered.@@ -180,6 +183,8 @@ drivers/usb/input/hid-core.c: v2.0:USB HID core driver mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 +usb 1-2: new low speed USB device using address 2 +input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:02.0-2 Synaptics Touchpad, model: 1 Firmware: 5.9 Sensor: 35@@ -189,7 +194,6 @@ -> palm detection input: SynPS/2 Synaptics TouchPad on isa0060/serio1 Advanced Linux Sound Architecture Driver Version 1.0.6 (Sun Aug 1507:17:53 2004 UTC).
dmesg 2004-09-23 10:07:34.000000000 -0700 renamed from dmesg 2004-09-23 10:09:57.615512000 -0700 +1
-3-ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5 ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 5 (level, low) -> IRQ 5 ALSA device list: #0: ALI 5451 at 0x8400, irq 5@@ -216,10 +220,9 @@ Adding 1004052k swap on /dev/hda3. Priority:-1 extents:1 Linux Kernel Card Services options: [pci] [cardbus] [pm] -ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11 ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 11 (level, low) -> IRQ 11 Yenta: CardBus bridge found at 0000:00:0a.0 [0000:0000] -Yenta: ISA IRQ mask 0x0498, PCI irq 11 +Yenta: ISA IRQ mask 0x0098, PCI irq 11 Socket status: 30000007 eth0: DSPCFG accepted after 0 usec. eth0: link up.lspci:
0000:00:00.0 Host bridge: ATI Technologies Inc AGP Bridge [IGP 320M] (rev 13) 0000:00:01.0 PCI bridge: ATI Technologies Inc PCI Bridge [IGP 320M] (rev 01) 0000:00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) 0000:00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 02)
0000:00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV] 0000:00:08.0 Modem: ALi Corporation M5457 AC'97 Modem Controller 0000:00:0a.0 CardBus bridge: O2 Micro, Inc. OZ6912 Cardbus Controller 0000:00:0c.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link)
0000:00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c4) 0000:00:11.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU] 0000:00:12.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller
0000:01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility U1Let me know if you require any additional information.
Cheers,
Andre
Quoted 3 lines · Andre Eisenbach
when booting with a recent kernel (2.6.9-rc2-mm2),
usb_ohcifails to initialize the USB bus and no USB device will work at that point. Adding pci=routeirq fixed the problem.
Can you try this whitespace-damaged patch to see whether you're seeing the same issue I was? If this patch fixes it, please post the "lspci -n" output for your USB controller, so we can add a quirk for it.
drivers/usb/host/ohci-hcd.c 2004-09-24 10:28:23.089214712 -0600 renamed from drivers/usb/host/ohci-hcd.c.orig 2004-09-24 10:28:16.383160107 -0600 +1 -1
@@ -564,7 +564,7 @@ * (SiS, OPTi ...), so reset again instead. SiS doesn't need * this if we write fmInterval after we're OPERATIONAL. */ - if (ohci->flags & OHCI_QUIRK_INITRESET) { + if (1 || ohci->flags & OHCI_QUIRK_INITRESET) { writel (ohci->hc_control, &ohci->regs->control); // flush those writes (void) ohci_readl (&ohci->regs->control);
Sorry for the late reply ...
Quoted 4 lines · Bjorn Helgaas
Can you try this whitespace-damaged patch to see whether you're seeing the same issue I was? If this patch fixes it, please post the "lspci -n" output for your USB controller, so we can add a quirk for it.
Yes, this patch fixes the problem.
I've submitted a different patch based on the testing results (Email
subject: [PATCH] ohci_hcd: ALi USB M5237 host controller init quirk), which enables the quirk for my USB controller. That hopefully will save you some work.
The lspci -n output (for reference) is:
0000:00:02.0 Class 0c03: 10b9:5237 (rev 03)
Which equals:PCI_VENDOR_ID_AL / PCI_DEVICE_ID_AL_M5237
Thanks,
Andre Eisenbach