Skip to contentSkip to conversation

Meson8b: add support for the Endless Mini EC-100

PATCH New Martin Blumenstingl 2 participants 7 messages Sep 22, 2018 – Sep 26, 2018

Subsystems (3)
lore
Share & tools
lore

Martin Blumenstingl

author reviewer
#0 lore raw

v2 cover Meson8b: add support for the Endless Mini EC-100

This series adds support for the "Endless Mini" grapefruit-sized mini PC from Endless Mobile, Inc. The internal name of this device is EC-100 (this can be found for example in the GPL kernel tree which is based on Amlogic's 3.10 kernel: [0]).

The board is using a Meson8b (S805) SoC with various peripherals. The biggest difference compared to boards which are based on Amlogic's reference designs is that this board comes with an embedded micro- controller called "EC" which makes the system LED pulse during boot and allows powering off the board. It also comes with a 10/100 Mbit/s Ethernet port and one USB host port.
There are two variants:
- 2GB RAM, 32GB storage, 802.11bgn and Bluetooth 4.0
- 1GB RAM, 24GB storage, neither wifi nor Bluetooth

This series contains support for the new board as well as supporting patches for the new vendor prefix and the pin definitions in meson8b.dtsi so various peripherals can be enabled.

Changes since v1 at [1]:
- added Rob's "Acked-by" to the dt-bindings patches (#1 and #2)
- changed the compatible string from endless,ec-100 to endless,ec100 to match what is being shipped with the 3.10 based kernel (suggested by Daniel Drake) as well as being consistent with the .dts file naming

[0] https://github.com/endlessm/linux-meson/blob/d628bf1242928927a41f7482ba5ef7295e01a9ff/arch/arm/boot/dts/meson8b-ec100.dts
[1] http://lists.infradead.org/pipermail/linux-amlogic/2018-September/008342.html

Martin Blumenstingl (5):
dt-bindings: add vendor prefix for "Endless Mobile, Inc."
dt-bindings: arm: amlogic: Add the Endless Mobile Endless Mini

    (EC-100)

ARM: dts: meson8b: add the I2C_A, PWM_C and UART_B pins
ARM: dts: meson8b: add the RMII pins
ARM: dts: meson8b: Add support for the Endless Mini (EC-100)

 .../devicetree/bindings/arm/amlogic.txt       |   1 +
 .../devicetree/bindings/vendor-prefixes.txt   |   1 +
 arch/arm/boot/dts/Makefile                    |   1 +
 arch/arm/boot/dts/meson8b-ec100.dts           | 248 ++++++++++++++++++
 arch/arm/boot/dts/meson8b.dtsi                |  45 ++++
 5 files changed, 296 insertions(+)
 create mode 100644 arch/arm/boot/dts/meson8b-ec100.dts
Signature · 1 line
2.19.0
author reviewer
#1 lore raw

PATCH v2 1/5 dt-bindings: add vendor prefix for "Endless Mobile, Inc."

Endless Mobile, Inc. started selling (small) computers in 2015.

---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -0
index 2c3fc512e746..1c63d2c2d48f 100644
@@ -114,6 +114,7 @@ elan	Elan Microelectronic Corp.
 embest	Shenzhen Embest Technology Co., Ltd.
 emmicro	EM Microelectronic
 emtrion	emtrion GmbH
+endless	Endless Mobile, Inc.
 energymicro	Silicon Laboratories (formerly Energy Micro AS)
 engicam	Engicam S.r.l.
 epcos	EPCOS AG
Signature · 1 line
2.19.0
author reviewer
#2 lore raw

PATCH v2 2/5 dt-bindings: arm: amlogic: Add the Endless Mobile Endless Mini (EC-100)

In reply to Martin Blumenstingl

Add bindings documentation for the Endless Mini (EC-100) from Endless Mobile.

---
 Documentation/devicetree/bindings/arm/amlogic.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/amlogic.txt +1 -0
index b5c2b5c35766..2c2eee206736 100644
@@ -63,6 +63,7 @@ Board compatible values (alphabetically, grouped by SoC):
 
   - "minix,neo-x8" (Meson8)
 
+  - "endless,ec100" (Meson8b)
   - "hardkernel,odroid-c1" (Meson8b)
   - "tronfy,mxq" (Meson8b)
 
Signature · 1 line
2.19.0
author reviewer
#3 lore raw

PATCH v2 3/5 ARM: dts: meson8b: add the I2C_A, PWM_C and UART_B pins

In reply to Martin Blumenstingl

These are used for example on the Endless Mini (EC-100):
- I2C_A is connected to the Realtek RT5640 audio codec
- PWM_C (GPIODV_9) is connected to a PWM regulator which is used for VCCK (CPU voltage supply)
- UART_B is connected to the Bluetooth module (of the RTL8723BS SDIO wifi and Bluetooth combo chip)

---
 arch/arm/boot/dts/meson8b.dtsi | 30 ++++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)
arch/arm/boot/dts/meson8b.dtsi +30 -0
index f77e419c1c65..4bbbbc6bea83 100644
@@ -223,6 +223,13 @@
 			};
 		};
 
+		i2c_a_pins: i2c-a {
+			mux {
+				groups = "i2c_sda_a", "i2c_sck_a";
+				function = "i2c_a";
+			};
+		};
+
 		sd_b_pins: sd-b {
 			mux {
 				groups = "sd_d0_b", "sd_d1_b", "sd_d2_b",
@@ -230,6 +237,29 @@
 				function = "sd_b";
 			};
 		};
+
+		pwm_c1_pins: pwm-c1 {
+			mux {
+				groups = "pwm_c1";
+				function = "pwm_c";
+			};
+		};
+
+		uart_b0_pins: uart-b0 {
+			mux {
+				groups = "uart_tx_b0",
+				       "uart_rx_b0";
+				function = "uart_b";
+			};
+		};
+
+		uart_b0_cts_rts_pins: uart-b0-cts-rts {
+			mux {
+				groups = "uart_cts_b0",
+				       "uart_rts_b0";
+				function = "uart_b";
+			};
+		};
 	};
 };
 
Signature · 1 line
2.19.0
author reviewer
#4 lore raw

PATCH v2 4/5 ARM: dts: meson8b: add the RMII pins

In reply to Martin Blumenstingl

Some boards use an RMII Ethernet PHY which requires fewer pins than the RGMII PHYs. Add a separate eth_rmii_pins node which does not include the pins which are only required for RGMII (but not for RMII) PHYs.

---
 arch/arm/boot/dts/meson8b.dtsi | 15 +++++++++++++++
 1 file changed, 15 insertions(+)
arch/arm/boot/dts/meson8b.dtsi +15 -0
index 4bbbbc6bea83..cd1ca9dda126 100644
@@ -223,6 +223,21 @@
 			};
 		};
 
+		eth_rmii_pins: eth-rmii {
+			mux {
+				groups = "eth_tx_en",
+					 "eth_txd1_0",
+					 "eth_txd0_0",
+					 "eth_rx_clk",
+					 "eth_rx_dv",
+					 "eth_rxd1",
+					 "eth_rxd0",
+					 "eth_mdio_en",
+					 "eth_mdc";
+				function = "ethernet";
+			};
+		};
+
 		i2c_a_pins: i2c-a {
 			mux {
 				groups = "i2c_sda_a", "i2c_sck_a";
Signature · 1 line
2.19.0
author reviewer
#5 lore raw

PATCH v2 5/5 ARM: dts: meson8b: Add support for the Endless Mini (EC-100)

In reply to Martin Blumenstingl

The Endless Mini (EC-100) is a grapefruit-sized computer based on the Amlogic Meson8b (S805) SoC which comes in two variants.

Both variants have in common:
- Amlogic Meson8b (S805) SoC
- two USB 2.0 ports on the rear, one one the front (connected to the SoC through an internal hub)
- 3.5mm Stereo out and MIC combo port
- HDMI and CVBS output
- 5V power supply (rated at 3A / 15W)
- an internal embedded micro-controller (called "EC") which implements a "breathing" effect for the LED and allows shutting down (powering off) the whole device
- 10/100 Mbit/s Ethernet using an IC Plus IP101A/G PHY (note: the website incorrectly lists a Gigabit Ethernet port)
- the CPU voltage is regulated using a PWM regulator. The GPL sources of the EC-100 are using a PWM value of 0x1c0000 for 0.86V and a PWM value of 0x00001c for 1.14V. When using the XTAL (24MHz) as input this translates into a PWM period of 1148ns with 0.86V using a duty cycle of 100% and 1.14V using a duty cycle of 0%.

The main differences are:
- the main indicator for the variant is the RAM size: the "cheaper" variant has 1 GB of RAM, while the more expensive one comes with 2GB
- the storage size differs: 24 GB vs 32 GB
- the "1 GB RAM" variant has Ethernet connectivity only, while the "2 GB" variant has a Realtek RTL8723BS SDIO chip which adds 802.11b/g/n wifi and Bluetooth 4.0 support

---
 arch/arm/boot/dts/Makefile          |   1 +
 arch/arm/boot/dts/meson8b-ec100.dts | 248 ++++++++++++++++++++++++++++
 2 files changed, 249 insertions(+)
 create mode 100644 arch/arm/boot/dts/meson8b-ec100.dts
arch/arm/boot/dts/Makefile +1 -0
index b5bd3de87c33..856ebc036cc4 100644
@@ -321,6 +321,7 @@ dtb-$(CONFIG_MACH_MESON6) += \
 	meson6-atv1200.dtb
 dtb-$(CONFIG_MACH_MESON8) += \
 	meson8-minix-neo-x8.dtb \
+	meson8b-ec100.dtb \
 	meson8b-mxq.dtb \
 	meson8b-odroidc1.dtb \
 	meson8m2-mxiii-plus.dtb
arch/arm/boot/dts/meson8b-ec100.dts new file +248 -0

248 lines not on this page · raw message

Signature · 1 line
2.19.0
maintainer Applied
#6 lore raw

v2 cover Meson8b: add support for the Endless Mini EC-100

In reply to Martin Blumenstingl
Quoted 15 lines · Martin Blumenstingl

This series adds support for the "Endless Mini" grapefruit-sized mini PC from Endless Mobile, Inc. The internal name of this device is EC-100 (this can be found for example in the GPL kernel tree which is based on Amlogic's 3.10 kernel: [0]).

The board is using a Meson8b (S805) SoC with various peripherals. The biggest difference compared to boards which are based on Amlogic's reference designs is that this board comes with an embedded micro- controller called "EC" which makes the system LED pulse during boot and allows powering off the board. It also comes with a 10/100 Mbit/s Ethernet port and one USB host port.
There are two variants:
- 2GB RAM, 32GB storage, 802.11bgn and Bluetooth 4.0
- 1GB RAM, 24GB storage, neither wifi nor Bluetooth

Quoted 3 lines

This series contains support for the new board as well as supporting patches for the new vendor prefix and the pin definitions in meson8b.dtsi so various peripherals can be enabled.

Applied to v4.20/dt,

Thanks,

Kevin