Skip to contentSkip to conversation

arm64: dts: meson: add W400 dtsi and GT-King/Pro devices

PATCH Superseded Christian Hewitt 2 participants 7 messages May 18, 2020 – May 19, 2020

Subsystems (2)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

v3 cover arm64: dts: meson: add W400 dtsi and GT-King/Pro devices

This series combines patch 2 from [1] which converts the existing Ugoos AM6 device-tree to a common W400 dtsi and dts, and then reworks the Beelink GT-King/GT-King Pro serries from [2] to use the dtsi, but this time without the offending common audio dtsi approach. I've carried forwards acks on bindings from Rob as these did not change.

v3 - amend author full-name on bindings patch

[1] https://patchwork.kernel.org/patch/11497105/
[2] https://patchwork.kernel.org/project/linux-amlogic/list/?series=273483

Christian Hewitt (5):
arm64: dts: meson: convert ugoos-am6 to common w400 dtsi
dt-bindings: arm: amlogic: add support for the Beelink GT-King
arm64: dts: meson-g12b-gtking: add initial device-tree
dt-bindings: arm: amlogic: add support for the Beelink GT-King Pro
arm64: dts: meson-g12b-gtking-pro: add initial device-tree

 .../devicetree/bindings/arm/amlogic.yaml      |   2 +
 arch/arm64/boot/dts/amlogic/Makefile          |   2 +
 .../dts/amlogic/meson-g12b-gtking-pro.dts     | 125 ++++++
 .../boot/dts/amlogic/meson-g12b-gtking.dts    | 145 ++++++
 .../boot/dts/amlogic/meson-g12b-ugoos-am6.dts | 410 +----------------
 .../boot/dts/amlogic/meson-g12b-w400.dtsi     | 423 ++++++++++++++++++
 6 files changed, 698 insertions(+), 409 deletions(-)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
Signature · 1 line
2.17.1
#1 lore raw

PATCH v3 1/5 arm64: dts: meson: convert ugoos-am6 to common w400 dtsi

Convert the Ugoos AM6 dts into meson-g12b-w400.dtsi, and then create a new AM6 dts that references it. This is in preparation for several new G12B devices that will share the common w400 dtsi.

---
 .../boot/dts/amlogic/meson-g12b-ugoos-am6.dts | 410 +----------------
 .../boot/dts/amlogic/meson-g12b-w400.dtsi     | 423 ++++++++++++++++++
 2 files changed, 424 insertions(+), 409 deletions(-)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts +1 -409
index fdaacfd96b97..73637de80c21 100644
@@ -7,42 +7,13 @@
 
 /dts-v1/;
 
-#include "meson-g12b.dtsi"
-#include "meson-g12b-s922x.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include "meson-g12b-w400.dtsi"
 #include <dt-bindings/sound/meson-g12a-tohdmitx.h>
 
 / {
 	compatible = "ugoos,am6", "amlogic,s922x", "amlogic,g12b";
 	model = "Ugoos AM6";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x0 0x0 0x0 0x40000000>;
-	};
-
-	emmc_pwrseq: emmc-pwrseq {
-		compatible = "mmc-pwrseq-emmc";
-		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
-	};
-
-	sdio_pwrseq: sdio-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
-		clocks = <&wifi32k>;
-		clock-names = "ext_clock";
-	};
-
 	spdif_dit: audio-codec-1 {
 		#sound-dai-cells = <0>;
 		compatible = "linux,spdif-dit";
@@ -50,154 +21,6 @@
 		sound-name-prefix = "DIT";
 	};
 
-	flash_1v8: regulator-flash_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "FLASH_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vcc_3v3>;
-		regulator-always-on;
-	};
-
-	main_12v: regulator-main_12v {
-		compatible = "regulator-fixed";
-		regulator-name = "12V";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		regulator-always-on;
-	};
-
-	vcc_5v: regulator-vcc_5v {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC_5V";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&main_12v>;
-
-		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
-		enable-active-high;
-	};
-
-	vcc_1v8: regulator-vcc_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vcc_3v3>;
-		regulator-always-on;
-	};
-
-	vcc_3v3: regulator-vcc_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-		/* FIXME: actually controlled by VDDCPU_B_EN */
-	};
-
-	vddcpu_a: regulator-vddcpu-a {
-		/*
-		 * MP1653 Regulator.
-		 */
-		compatible = "pwm-regulator";
-
-		regulator-name = "VDDCPU_A";
-		regulator-min-microvolt = <721000>;
-		regulator-max-microvolt = <1022000>;
-
-		vin-supply = <&main_12v>;
-
-		pwms = <&pwm_ab 0 1250 0>;
-		pwm-dutycycle-range = <100 0>;
-
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	vddcpu_b: regulator-vddcpu-b {
-		/*
-		 * MP1652 Regulator.
-		 */
-		compatible = "pwm-regulator";
-
-		regulator-name = "VDDCPU_B";
-		regulator-min-microvolt = <721000>;
-		regulator-max-microvolt = <1022000>;
-
-		vin-supply = <&main_12v>;
-
-		pwms = <&pwm_AO_cd 1 1250 0>;
-		pwm-dutycycle-range = <100 0>;
-
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	usb1_pow: regulator-usb1-pow {
-		compatible = "regulator-fixed";
-		regulator-name = "USB1_POW";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc_5v>;
-
-		/* connected to SY6280A Power Switch */
-		gpio = <&gpio GPIOA_8 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	usb_pwr_en: regulator-usb-pwr-en {
-		compatible = "regulator-fixed";
-		regulator-name = "USB_PWR_EN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc_5v>;
-
-		/* Connected to USB3 Type-A Port power enable */
-		gpio = <&gpio GPIOAO_7 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vddao_1v8: regulator-vddao-1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	vddao_3v3: regulator-vddao-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&main_12v>;
-		regulator-always-on;
-	};
-
-	cvbs-connector {
-		compatible = "composite-video-connector";
-
-		port {
-			cvbs_connector_in: endpoint {
-				remote-endpoint = <&cvbs_vdac_out>;
-			};
-		};
-	};
-
-	hdmi-connector {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&hdmi_tx_tmds_out>;
-			};
-		};
-	};
-
 	sound {
 		compatible = "amlogic,axg-sound-card";
 		model = "G12B-UGOOS-AM6";
@@ -277,110 +100,16 @@
 			};
 		};
 	};
-
-	wifi32k: wifi32k {
-		compatible = "pwm-clock";
-		#clock-cells = <0>;
-		clock-frequency = <32768>;
-		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
-	};
 };
 
 &arb {
 	status = "okay";
 };
 
-&cec_AO {
-	pinctrl-0 = <&cec_ao_a_h_pins>;
-	pinctrl-names = "default";
-	status = "disabled";
-	hdmi-phandle = <&hdmi_tx>;
-};
-
-&cecb_AO {
-	pinctrl-0 = <&cec_ao_b_h_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-	hdmi-phandle = <&hdmi_tx>;
-};
-
 &clkc_audio {
 	status = "okay";
 };
 
-&cpu0 {
-	cpu-supply = <&vddcpu_b>;
-	operating-points-v2 = <&cpu_opp_table_0>;
-	clocks = <&clkc CLKID_CPU_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu1 {
-	cpu-supply = <&vddcpu_b>;
-	operating-points-v2 = <&cpu_opp_table_0>;
-	clocks = <&clkc CLKID_CPU_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu100 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu101 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu102 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu103 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cvbs_vdac_port {
-	cvbs_vdac_out: endpoint {
-		remote-endpoint = <&cvbs_connector_in>;
-	};
-};
-
-&ext_mdio {
-	external_phy: ethernet-phy@0 {
-		/* Realtek RTL8211F (0x001cc916) */
-		reg = <0>;
-		max-speed = <1000>;
-
-		reset-assert-us = <10000>;
-		reset-deassert-us = <30000>;
-		reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
-
-		interrupt-parent = <&gpio_intc>;
-		/* MAC_INTR on GPIOZ_14 */
-		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
-	};
-};
-
-&ethmac {
-	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-	phy-mode = "rgmii";
-	phy-handle = <&external_phy>;
-	amlogic,tx-delay-ns = <2>;
-};
-
 &frddr_a {
 	status = "okay";
 };
@@ -393,112 +122,10 @@
 	status = "okay";
 };
 
-&hdmi_tx {
-	status = "okay";
-	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
-	pinctrl-names = "default";
-	hdmi-supply = <&vcc_5v>;
-};
-
-&hdmi_tx_tmds_port {
-	hdmi_tx_tmds_out: endpoint {
-		remote-endpoint = <&hdmi_connector_in>;
-	};
-};
-
 &ir {
-	status = "okay";
-	pinctrl-0 = <&remote_input_ao_pins>;
-	pinctrl-names = "default";
 	linux,rc-map-name = "rc-khadas";
 };
 
-&pwm_ab {
-	pinctrl-0 = <&pwm_a_e_pins>;
-	pinctrl-names = "default";
-	clocks = <&xtal>;
-	clock-names = "clkin0";
-	status = "okay";
-};
-
-&pwm_AO_cd {
-	pinctrl-0 = <&pwm_ao_d_e_pins>;
-	pinctrl-names = "default";
-	clocks = <&xtal>;
-	clock-names = "clkin1";
-	status = "okay";
-};
-
-&pwm_ef {
-	pinctrl-0 = <&pwm_e_pins>;
-	pinctrl-names = "default";
-	clocks = <&xtal>;
-	clock-names = "clkin0";
-	status = "okay";
-};
-
-/* SDIO */
-&sd_emmc_a {
-	status = "okay";
-	pinctrl-0 = <&sdio_pins>;
-	pinctrl-1 = <&sdio_clk_gate_pins>;
-	pinctrl-names = "default", "clk-gate";
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	bus-width = <4>;
-	cap-sd-highspeed;
-	sd-uhs-sdr50;
-	max-frequency = <100000000>;
-
-	non-removable;
-	disable-wp;
-
-	mmc-pwrseq = <&sdio_pwrseq>;
-
-	vmmc-supply = <&vddao_3v3>;
-	vqmmc-supply = <&vddao_1v8>;
-
-	brcmf: wifi@1 {
-		reg = <1>;
-		compatible = "brcm,bcm4329-fmac";
-	};
-};
-
-/* SD card */
-&sd_emmc_b {
-	status = "okay";
-	pinctrl-0 = <&sdcard_c_pins>;
-	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <4>;
-	cap-sd-highspeed;
-	max-frequency = <50000000>;
-	disable-wp;
-
-	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&vddao_3v3>;
-	vqmmc-supply = <&vddao_3v3>;
-};
-
-/* eMMC */
-&sd_emmc_c {
-	status = "okay";
-	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
-	pinctrl-1 = <&emmc_clk_gate_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <8>;
-	cap-mmc-highspeed;
-	max-frequency = <100000000>;
-	disable-wp;
-
-	mmc-pwrseq = <&emmc_pwrseq>;
-	vmmc-supply = <&vcc_3v3>;
-	vqmmc-supply = <&flash_1v8>;
-};
-
 &spdifout {
 	pinctrl-0 = <&spdif_out_h_pins>;
 	pinctrl-names = "default";
@@ -520,38 +147,3 @@
 &tohdmitx {
 	status = "okay";
 };
-
-&uart_A {
-	status = "okay";
-	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
-	pinctrl-names = "default";
-	uart-has-rtscts;
-
-	bluetooth {
-		compatible = "brcm,bcm43438-bt";
-		shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
-		max-speed = <2000000>;
-		clocks = <&wifi32k>;
-	clock-names = "lpo";
-	};
-};
-
-&uart_AO {
-	status = "okay";
-	pinctrl-0 = <&uart_ao_a_pins>;
-	pinctrl-names = "default";
-};
-
-&usb {
-	status = "okay";
-	dr_mode = "host";
-	vbus-supply = <&usb_pwr_en>;
-};
-
-&usb2_phy0 {
-	phy-supply = <&usb1_pow>;
-};
-
-&usb2_phy1 {
-	phy-supply = <&usb1_pow>;
-};
arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi new file +423 -0

423 lines not on this page · raw message

Signature · 1 line
2.17.1
#2 lore raw

PATCH v3 2/5 dt-bindings: arm: amlogic: add support for the Beelink GT-King

In reply to Christian Hewitt

The Shenzen AZW (Beelink) GT-King is based on the Amlogic W400 reference board with an S922X chip.

---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/amlogic.yaml +1 -0
index 5180a548bd94..25e118b8a97b 100644
@@ -151,6 +151,7 @@ properties:
       - description: Boards with the Amlogic Meson G12B S922X SoC
         items:
           - enum:
+              - azw,gtking
               - hardkernel,odroid-n2
               - khadas,vim3
               - ugoos,am6
Signature · 1 line
2.17.1
#3 lore raw

PATCH v3 3/5 arm64: dts: meson-g12b-gtking: add initial device-tree

In reply to Christian Hewitt

The Shenzen AZW (Beelink) GT-King is based on the Amlogic W400 reference board with an S922X chip.

- 4GB LPDDR4 RAM
- 64GB eMMC storage
- 10/100/1000 Base-T Ethernet
- AP6356S Wireless (802.11 a/b/g/n/ac, BT 4.1)
- HDMI 2.1 video
- S/PDIF optical output
- Analogue audio output
- 1x USB 2.0 port
- 2x USB 3.0 ports
- IR receiver
- 1x micro SD card slot

---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../boot/dts/amlogic/meson-g12b-gtking.dts    | 145 ++++++++++++++++++
 2 files changed, 146 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts
arch/arm64/boot/dts/amlogic/Makefile +1 -0
index 01e32415e252..66691090b30c 100644
@@ -4,6 +4,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-tanix-tx5max.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts new file +145 -0

145 lines not on this page · raw message

Signature · 1 line
2.17.1
#4 lore raw

PATCH v3 4/5 dt-bindings: arm: amlogic: add support for the Beelink GT-King Pro

In reply to Christian Hewitt

The Shenzen AZW (Beelink) GT-King Pro is based on the Amlogic W400 reference board with an S922X chip.

---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/amlogic.yaml +1 -0
index 25e118b8a97b..46cb6359f530 100644
@@ -152,6 +152,7 @@ properties:
         items:
           - enum:
               - azw,gtking
+              - azw,gtking-pro
               - hardkernel,odroid-n2
               - khadas,vim3
               - ugoos,am6
Signature · 1 line
2.17.1
#5 lore raw

PATCH v3 5/5 arm64: dts: meson-g12b-gtking-pro: add initial device-tree

In reply to Christian Hewitt

The Shenzen AZW (Beelink) GT-King Pro is based on the Amlogic W400 reference board with an S922X chip.

- 4GB LPDDR4 RAM
- 64GB eMMC storage
- 10/100/1000 Base-T Ethernet
- AP6356S Wireless (802.11 a/b/g/n/ac, BT 4.1)
- HDMI 2.1 video
- Analogue audio output
- 1x RS232 port
- 2x USB 2.0 port
- 2x USB 3.0 ports
- IR receiver
- 1x micro SD card slot
- 1x Power on/off button

---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../dts/amlogic/meson-g12b-gtking-pro.dts     | 125 ++++++++++++++++++
 2 files changed, 126 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
arch/arm64/boot/dts/amlogic/Makefile +1 -0
index 66691090b30c..38bb1f6e6ef6 100644
@@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12a-tanix-tx5max.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts new file +125 -0

125 lines not on this page · raw message

Signature · 1 line
2.17.1
maintainer
#6 lore raw
In reply to Christian Hewitt

Hi Christian,

Quoted 5 lines · Christian Hewitt

This series combines patch 2 from [1] which converts the existing Ugoos AM6 device-tree to a common W400 dtsi and dts, and then reworks the Beelink GT-King/GT-King Pro serries from [2] to use the dtsi, but this time without the offending common audio dtsi approach. I've carried forwards acks on bindings from Rob as these did not change.

This looks good to me, thank you very much for reworking into a w400-based include.

Unfortunately, it no longer applies on top of all the other stuff I have queued for v5.8.

Could you please do a rebase on top of my v5.8/dt64 branch[1], and I'll queue for v5.8.

Thanks,

Kevin

Quoted 25 lines

v3 - amend author full-name on bindings patch

[1] https://patchwork.kernel.org/patch/11497105/
[2] https://patchwork.kernel.org/project/linux-amlogic/list/?series=273483

Christian Hewitt (5):
arm64: dts: meson: convert ugoos-am6 to common w400 dtsi
dt-bindings: arm: amlogic: add support for the Beelink GT-King
arm64: dts: meson-g12b-gtking: add initial device-tree
dt-bindings: arm: amlogic: add support for the Beelink GT-King Pro
arm64: dts: meson-g12b-gtking-pro: add initial device-tree

 .../devicetree/bindings/arm/amlogic.yaml      |   2 +
 arch/arm64/boot/dts/amlogic/Makefile          |   2 +
 .../dts/amlogic/meson-g12b-gtking-pro.dts     | 125 ++++++
 .../boot/dts/amlogic/meson-g12b-gtking.dts    | 145 ++++++
 .../boot/dts/amlogic/meson-g12b-ugoos-am6.dts | 410 +----------------
 .../boot/dts/amlogic/meson-g12b-w400.dtsi     | 423 ++++++++++++++++++
 6 files changed, 698 insertions(+), 409 deletions(-)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
Signature · 1 line
2.17.1