Skip to contentSkip to conversation

iavf: initialize ITRN registers with correct values

PATCH New Alice Michael 2 participants 2 messages Nov 5, 2019 – Nov 7, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 iavf: initialize ITRN registers with correct values

From: Nicholas Nunley <[email protected]>

Since commit 92418fb14750 ("i40e/i40evf: Use usec value instead of reg value for ITR defines") the driver tracks the interrupt throttling intervals in single usec units, although the actual ITRN registers are programmed in 2 usec units. Most register programming flows in the driver correctly handle the conversion, although it is currently not applied when the registers are initialized to their default values. Most of the time this doesn't present a problem since the default values are usually immediately overwritten through the standard adaptive throttling mechanism, or updated manually by the user, but if adaptive throttling is disabled and the interval values are left alone then the incorrect value will persist.

Since the intended default interval of 50 usecs (vs. 100 usecs as programmed) performs better for most traffic workloads, this can lead to performance regressions.

This patch adds the correct conversion when writing the initial values to the ITRN registers.

---
 drivers/net/ethernet/intel/iavf/iavf_main.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/net/ethernet/intel/iavf/iavf_main.c +2 -2
index 8f310e520b06..821987da5698 100644
@@ -314,7 +314,7 @@ iavf_map_vector_to_rxq(struct iavf_adapter *adapter, int v_idx, int r_idx)
 	q_vector->rx.target_itr = ITR_TO_REG(rx_ring->itr_setting);
 	q_vector->ring_mask |= BIT(r_idx);
 	wr32(hw, IAVF_VFINT_ITRN1(IAVF_RX_ITR, q_vector->reg_idx),
-	     q_vector->rx.current_itr);
+	     q_vector->rx.current_itr >> 1);
 	q_vector->rx.current_itr = q_vector->rx.target_itr;
 }
 
@@ -340,7 +340,7 @@ iavf_map_vector_to_txq(struct iavf_adapter *adapter, int v_idx, int t_idx)
 	q_vector->tx.target_itr = ITR_TO_REG(tx_ring->itr_setting);
 	q_vector->num_ringpairs++;
 	wr32(hw, IAVF_VFINT_ITRN1(IAVF_TX_ITR, q_vector->reg_idx),
-	     q_vector->tx.target_itr);
+	     q_vector->tx.target_itr >> 1);
 	q_vector->tx.current_itr = q_vector->tx.target_itr;
 }
 
Signature · 1 line
2.21.0
#1 lore raw

PATCH 1/1 iavf: initialize ITRN registers with correct values

Quoted 26 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On Behalf Of Alice Michael
Sent: Tuesday, November 5, 2019 4:22 AM
To: Michael, Alice <[email protected]>; intel-wired-
lan at lists.osuosl.org
Subject: [Intel-wired-lan] [PATCH] iavf: initialize ITRN registers with correct values

From: Nicholas Nunley <[email protected]>

Since commit 92418fb14750 ("i40e/i40evf: Use usec value instead of reg value for ITR defines") the driver tracks the interrupt throttling intervals in single usec units, although the actual ITRN registers are programmed in 2 usec units. Most register programming flows in the driver correctly handle the conversion, although it is currently not applied when the registers are initialized to their default values. Most of the time this doesn't present a problem since the default values are usually immediately overwritten through the standard adaptive throttling mechanism, or updated manually by the user, but if adaptive throttling is disabled and the interval values are left alone then the incorrect value will persist.

Since the intended default interval of 50 usecs (vs. 100 usecs as programmed) performs better for most traffic workloads, this can lead to performance regressions.

Quoted 7 lines

This patch adds the correct conversion when writing the initial values to the ITRN registers.

---
 drivers/net/ethernet/intel/iavf/iavf_main.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)