amd_hsmp: Add HSMP protocol version 5 messages
Subsystems (3)
PATCH v3 1/1 amd_hsmp: Add HSMP protocol version 5 messages
From: Suma Hegde <[email protected]>
HSMP protocol version 5 is supported on AMD family 19h model 10h EPYC processors. This version brings new features such as -- DIMM statistics
-- Bandwidth for IO and xGMI links
-- Monitor socket and core frequency limits
-- Configure power efficiency modes, DF pstate range etc
---
changes since v2:
None, could not find the previous emails in the archives. Submitting again.
changes since v1:
spell correction in commit message
arch/x86/include/uapi/asm/amd_hsmp.h | 114 +++++++++++++++++++++++++-- 1 file changed, 109 insertions(+), 5 deletions(-)
arch/x86/include/uapi/asm/amd_hsmp.h +109 -5
@@ -31,9 +31,22 @@ enum hsmp_message_ids {HSMP_GET_CCLK_THROTTLE_LIMIT ,/* 10h Get CCLK frequency limit in socket */ HSMP_GET_C0_PERCENT ,/* 11h Get average C0 residency in socket */ HSMP_SET_NBIO_DPM_LEVEL ,/* 12h Set max/min LCLK DPM Level for a given NBIO */ -/* 13h Reserved */ -HSMP_GET_DDR_BANDWIDTH =0x14 ,/* 14h Get theoretical maximum and current DDR Bandwidth */ -HSMP_GET_TEMP_MONITOR ,/* 15h Get per-DIMM temperature and refresh rates */ +HSMP_GET_NBIO_DPM_LEVEL ,/* 13h Get LCLK DPM level min and max for a given NBIO */ +HSMP_GET_DDR_BANDWIDTH ,/* 14h Get theoretical maximum and current DDR Bandwidth */ +HSMP_GET_TEMP_MONITOR ,/* 15h Get socket temperature */ +HSMP_GET_DIMM_TEMP_RANGE ,/* 16h Get per-DIMM temperature range and refresh rate */ +HSMP_GET_DIMM_POWER ,/* 17h Get per-DIMM power consumption */ +HSMP_GET_DIMM_THERMAL ,/* 18h Get per-DIMM thermal sensors */ +HSMP_GET_SOCKET_FREQ_LIMIT ,/* 19h Get current active frequency per socket */ +HSMP_GET_CCLK_CORE_LIMIT ,/* 1Ah Get CCLK frequency limit per core */ +HSMP_GET_RAILS_SVI ,/* 1Bh Get SVI-based Telemetry for all rails */ +HSMP_GET_SOCKET_FMAX_FMIN ,/* 1Ch Get Fmax and Fmin per socket */ +HSMP_GET_IOLINK_BANDWITH ,/* 1Dh Get current bandwidth on IO Link */ +HSMP_GET_XGMI_BANDWITH ,/* 1Eh Get current bandwidth on xGMI Link */ +HSMP_SET_GMI3_WIDTH ,/* 1Fh Set max and min GMI3 Link width */ +HSMP_SET_PCI_RATE ,/* 20h Control link rate on PCIe devices */ +HSMP_SET_POWER_MODE ,/* 21h Select power efficiency profile policy */ +HSMP_SET_PSTATE_MAX_MIN ,/* 22h Set the max and min DF P-State */ HSMP_MSG_ID_MAX, };
@@ -175,8 +188,12 @@ static const struct hsmp_msg_desc hsmp_msg_desc_table[] = {*/ {1, 0, HSMP_SET}, -/* RESERVED message */ - {0, 0, HSMP_RSVD}, +/* +* HSMP_GET_NBIO_DPM_LEVEL, num_args = 1, response_sz = 1 +* input: args[0] = nbioid[23:16] +* output: args[0] = max dpm level[15:8] + min dpm level[7:0] +*/ + {1, 1, HSMP_GET},/* * HSMP_GET_DDR_BANDWIDTH, num_args = 0, response_sz = 1
@@ -191,6 +208,93 @@ static const struct hsmp_msg_desc hsmp_msg_desc_table[] = {* [7:5] fractional part */ {0, 1, HSMP_GET}, + +/* +* HSMP_GET_DIMM_TEMP_RANGE, num_args = 1, response_sz = 1 +* input: args[0] = DIMM address[7:0] +* output: args[0] = refresh rate[3] + temperature range[2:0] +*/ + {1, 1, HSMP_GET}, + +/* +* HSMP_GET_DIMM_POWER, num_args = 1, response_sz = 1 +* input: args[0] = DIMM address[7:0] +* output: args[0] = DIMM power in mW[31:17] + update rate in ms[16:8] + +* DIMM address[7:0] +*/ + {1, 1, HSMP_GET}, + +/* +* HSMP_GET_DIMM_THERMAL, num_args = 1, response_sz = 1 +* input: args[0] = DIMM address[7:0] +* output: args[0] = temperature in degree celcius[31:21] + update rate in ms[16:8] + +* DIMM address[7:0] +*/ + {1, 1, HSMP_GET}, + +/* +* HSMP_GET_SOCKET_FREQ_LIMIT, num_args = 0, response_sz = 1 +* output: args[0] = frequency in MHz[31:16] + frequency source[15:0] +*/ + {0, 1, HSMP_GET}, + +/* +* HSMP_GET_CCLK_CORE_LIMIT, num_args = 1, response_sz = 1 +* input: args[0] = apic id [31:0] +* output: args[0] = frequency in MHz[31:0] +*/ + {1, 1, HSMP_GET}, + +/* +* HSMP_GET_RAILS_SVI, num_args = 0, response_sz = 1 +* output: args[0] = power in mW[31:0] +*/ + {0, 1, HSMP_GET}, + +/* +* HSMP_GET_SOCKET_FMAX_FMIN, num_args = 0, response_sz = 1 +* output: args[0] = fmax in MHz[31:16] + fmin in MHz[15:0] +*/ + {0, 1, HSMP_GET}, + +/* +* HSMP_GET_IOLINK_BANDWITH, num_args = 1, response_sz = 1 +* input: args[0] = link id[15:8] + bw type[2:0] +* output: args[0] = io bandwidth in Mbps[31:0] +*/ + {1, 1, HSMP_GET}, + +/* +* HSMP_GET_XGMI_BANDWITH, num_args = 1, response_sz = 1 +* input: args[0] = link id[15:8] + bw type[2:0] +* output: args[0] = xgmi bandwidth in Mbps[31:0] +*/ + {1, 1, HSMP_GET}, + +/* +* HSMP_SET_GMI3_WIDTH, num_args = 1, response_sz = 0 +* input: args[0] = min link width[15:8] + max link width[7:0] +*/ + {1, 0, HSMP_SET}, + +/* +* HSMP_SET_PCI_RATE, num_args = 1, response_sz = 1 +* input: args[0] = link rate control value +* output: args[0] = previous link rate control value +*/ + {1, 1, HSMP_SET}, + +/* +* HSMP_SET_POWER_MODE, num_args = 1, response_sz = 0 +* input: args[0] = power efficiency mode[2:0] +*/ + {1, 0, HSMP_SET}, + +/* +* HSMP_SET_PSTATE_MAX_MIN, num_args = 1, response_sz = 0 +* input: args[0] = min df pstate[15:8] + max df pstate[7:0] +*/ + {1, 0, HSMP_SET}, };/* Reset to default packing */
Signature · 1 line
2.27.0
Hi,
Quoted 9 lines · Naveen Krishna Chatradhi
From: Suma Hegde <[email protected]>
HSMP protocol version 5 is supported on AMD family 19h model 10h EPYC processors. This version brings new features such as -- DIMM statistics
-- Bandwidth for IO and xGMI links
-- Monitor socket and core frequency limits
-- Configure power efficiency modes, DF pstate range etc
Quoted 3 lines
Signed-off-by Suma Hegde <[email protected]>Reviewed-by Carlos Bilbao <[email protected]>Signed-off-by Naveen Krishna Chatradhi <[email protected]>
Thank you for your patch, I've applied this patch to my review-hans branch:
https://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86.git/log/?h=review-hans
Note it will show up in my review-hans branch once I've pushed my local branch there, which might take a while.
Once I've run some tests on this branch the patches there will be added to the platform-drivers-x86/for-next branch and eventually will be included in the pdx86 pull-request to Linus for the next merge-window.
Regards,
Hans
Quoted 150 lines
---
changes since v2:
None, could not find the previous emails in the archives. Submitting again.changes since v1:
spell correction in commit messagearch/x86/include/uapi/asm/amd_hsmp.h | 114 +++++++++++++++++++++++++-- 1 file changed, 109 insertions(+), 5 deletions(-)arch/x86/include/uapi/asm/amd_hsmp.h +109
-5@@ -31,9 +31,22 @@ enum hsmp_message_ids {HSMP_GET_CCLK_THROTTLE_LIMIT ,/* 10h Get CCLK frequency limit in socket */ HSMP_GET_C0_PERCENT ,/* 11h Get average C0 residency in socket */ HSMP_SET_NBIO_DPM_LEVEL ,/* 12h Set max/min LCLK DPM Level for a given NBIO */ -/* 13h Reserved */ -HSMP_GET_DDR_BANDWIDTH =0x14 ,/* 14h Get theoretical maximum and current DDR Bandwidth */ -HSMP_GET_TEMP_MONITOR ,/* 15h Get per-DIMM temperature and refresh rates */ +HSMP_GET_NBIO_DPM_LEVEL ,/* 13h Get LCLK DPM level min and max for a given NBIO */ +HSMP_GET_DDR_BANDWIDTH ,/* 14h Get theoretical maximum and current DDR Bandwidth */ +HSMP_GET_TEMP_MONITOR ,/* 15h Get socket temperature */ +HSMP_GET_DIMM_TEMP_RANGE ,/* 16h Get per-DIMM temperature range and refresh rate */ +HSMP_GET_DIMM_POWER ,/* 17h Get per-DIMM power consumption */ +HSMP_GET_DIMM_THERMAL ,/* 18h Get per-DIMM thermal sensors */ +HSMP_GET_SOCKET_FREQ_LIMIT ,/* 19h Get current active frequency per socket */ +HSMP_GET_CCLK_CORE_LIMIT ,/* 1Ah Get CCLK frequency limit per core */ +HSMP_GET_RAILS_SVI ,/* 1Bh Get SVI-based Telemetry for all rails */ +HSMP_GET_SOCKET_FMAX_FMIN ,/* 1Ch Get Fmax and Fmin per socket */ +HSMP_GET_IOLINK_BANDWITH ,/* 1Dh Get current bandwidth on IO Link */ +HSMP_GET_XGMI_BANDWITH ,/* 1Eh Get current bandwidth on xGMI Link */ +HSMP_SET_GMI3_WIDTH ,/* 1Fh Set max and min GMI3 Link width */ +HSMP_SET_PCI_RATE ,/* 20h Control link rate on PCIe devices */ +HSMP_SET_POWER_MODE ,/* 21h Select power efficiency profile policy */ +HSMP_SET_PSTATE_MAX_MIN ,/* 22h Set the max and min DF P-State */ HSMP_MSG_ID_MAX, };@@ -175,8 +188,12 @@ static const struct hsmp_msg_desc hsmp_msg_desc_table[] = {*/ {1, 0, HSMP_SET}, -/* RESERVED message */ - {0, 0, HSMP_RSVD}, +/* +* HSMP_GET_NBIO_DPM_LEVEL, num_args = 1, response_sz = 1 +* input: args[0] = nbioid[23:16] +* output: args[0] = max dpm level[15:8] + min dpm level[7:0] +*/ + {1, 1, HSMP_GET},/* * HSMP_GET_DDR_BANDWIDTH, num_args = 0, response_sz = 1 @@ -191,6 +208,93 @@ static const struct hsmp_msg_desc hsmp_msg_desc_table[] = {* [7:5] fractional part */ {0, 1, HSMP_GET}, + +/* +* HSMP_GET_DIMM_TEMP_RANGE, num_args = 1, response_sz = 1 +* input: args[0] = DIMM address[7:0] +* output: args[0] = refresh rate[3] + temperature range[2:0] +*/ + {1, 1, HSMP_GET}, + +/* +* HSMP_GET_DIMM_POWER, num_args = 1, response_sz = 1 +* input: args[0] = DIMM address[7:0] +* output: args[0] = DIMM power in mW[31:17] + update rate in ms[16:8] + +* DIMM address[7:0] +*/ + {1, 1, HSMP_GET}, + +/* +* HSMP_GET_DIMM_THERMAL, num_args = 1, response_sz = 1 +* input: args[0] = DIMM address[7:0] +* output: args[0] = temperature in degree celcius[31:21] + update rate in ms[16:8] + +* DIMM address[7:0] +*/ + {1, 1, HSMP_GET}, + +/* +* HSMP_GET_SOCKET_FREQ_LIMIT, num_args = 0, response_sz = 1 +* output: args[0] = frequency in MHz[31:16] + frequency source[15:0] +*/ + {0, 1, HSMP_GET}, + +/* +* HSMP_GET_CCLK_CORE_LIMIT, num_args = 1, response_sz = 1 +* input: args[0] = apic id [31:0] +* output: args[0] = frequency in MHz[31:0] +*/ + {1, 1, HSMP_GET}, + +/* +* HSMP_GET_RAILS_SVI, num_args = 0, response_sz = 1 +* output: args[0] = power in mW[31:0] +*/ + {0, 1, HSMP_GET}, + +/* +* HSMP_GET_SOCKET_FMAX_FMIN, num_args = 0, response_sz = 1 +* output: args[0] = fmax in MHz[31:16] + fmin in MHz[15:0] +*/ + {0, 1, HSMP_GET}, + +/* +* HSMP_GET_IOLINK_BANDWITH, num_args = 1, response_sz = 1 +* input: args[0] = link id[15:8] + bw type[2:0] +* output: args[0] = io bandwidth in Mbps[31:0] +*/ + {1, 1, HSMP_GET}, + +/* +* HSMP_GET_XGMI_BANDWITH, num_args = 1, response_sz = 1 +* input: args[0] = link id[15:8] + bw type[2:0] +* output: args[0] = xgmi bandwidth in Mbps[31:0] +*/ + {1, 1, HSMP_GET}, + +/* +* HSMP_SET_GMI3_WIDTH, num_args = 1, response_sz = 0 +* input: args[0] = min link width[15:8] + max link width[7:0] +*/ + {1, 0, HSMP_SET}, + +/* +* HSMP_SET_PCI_RATE, num_args = 1, response_sz = 1 +* input: args[0] = link rate control value +* output: args[0] = previous link rate control value +*/ + {1, 1, HSMP_SET}, + +/* +* HSMP_SET_POWER_MODE, num_args = 1, response_sz = 0 +* input: args[0] = power efficiency mode[2:0] +*/ + {1, 0, HSMP_SET}, + +/* +* HSMP_SET_PSTATE_MAX_MIN, num_args = 1, response_sz = 0 +* input: args[0] = min df pstate[15:8] + max df pstate[7:0] +*/ + {1, 0, HSMP_SET}, };/* Reset to default packing */