ath10k - spectral scan - and - channel change
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hello, I searched the mail archives but couldn't find a clue to my question so here it is:
Im interested in performing a spectral scan of as much of the spectrum as possible, and quickly. this means scanning a channel for some time, changing channels, and repeating.
Background: when configuring an ath9k radio to Monitor mode, it is possible to do 2 things:
1) change wifi channel via command line, e.g. iw dev wlan1 set channel 3. This does it seemingly quickly, without taking down the interface (good)
2) control the debugfs files like /sys/kernel/debug/ieee80211/phy1/ath9k/spectral_scan_ctl (good)
The problem is:
ath10k, in Monitor mode, I am only able to change channels - 1) iw dev wlan0 set channel 104, but not access the debugfs files 2) (which is essential to control and obtain the spectral scan result) the error I get is:
root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device
ath10k, in AP mode, The opposite occurs - I am only able to access debugfs files 2) , but not change channel 1), which is annoying because I cant then scan the entire possible range.
the error I get is one of:
root@OpenWrt:~# iw dev wlan0 set channel 112
command failed: Device or resource busy (-16)
or
root@OpenWrt:~# iw dev wlan0 set channel 104 command failed: Invalid argument (-22)
Is there anything I can do to get both working?
Thanks. Will
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
pinging and compacting the Q just in case the experts have an idea on this..
Is it possible to control spectral_scan_ctl whilst in AP mode? my result:
root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device
or
change channel whilst in Monitor mode?
my result:
root@OpenWrt:~# iw dev wlan0 set channel 112 command failed: Device or resource busy (-16)
Thanks Will.
________________________________
From: Will Kerr <[email protected]>
To: "[email protected]" <[email protected]>
Sent: Friday, 24 February 2017, 6:49
Subject: ath10k - spectral scan - and - channel change
Hello, I searched the mail archives but couldn't find a clue to my question so here it is:
Im interested in performing a spectral scan of as much of the spectrum as possible, and quickly. this means scanning a channel for some time, changing channels, and repeating.
Background: when configuring an ath9k radio to Monitor mode, it is possible to do 2 things:
1) change wifi channel via command line, e.g. iw dev wlan1 set channel 3. This does it seemingly quickly, without taking down the interface (good)
2) control the debugfs files like /sys/kernel/debug/ieee80211/phy1/ath9k/spectral_scan_ctl (good)
The problem is:
ath10k, in Monitor mode, I am only able to change channels - 1) iw dev wlan0 set channel 104, but not access the debugfs files 2) (which is essential to control and obtain the spectral scan result) the error I get is:
root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device
ath10k, in AP mode, The opposite occurs - I am only able to access debugfs files 2) , but not change channel 1), which is annoying because I cant then scan the entire possible range.
the error I get is one of:
root@OpenWrt:~# iw dev wlan0 set channel 112
command failed: Device or resource busy (-16)
or
root@OpenWrt:~# iw dev wlan0 set channel 104 command failed: Invalid argument (-22)
Is there anything I can do to get both working?
Thanks. Will
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
please follow
https://wireless.wiki.kernel.org/en/users/drivers/ath10k/spectral
please check if phy0 does exists ?
________________________________________
From: ath10k <[email protected]> on behalf of Will Kerr <[email protected]>
Sent: 06 March 2017 22:27
To: [email protected]
Subject: Re: ath10k - spectral scan - and - channel change
pinging and compacting the Q just in case the experts have an idea on this..
Is it possible to control spectral_scan_ctl whilst in AP mode? my result:
root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device
or
change channel whilst in Monitor mode?
my result:
root@OpenWrt:~# iw dev wlan0 set channel 112 command failed: Device or resource busy (-16)
Thanks Will.
________________________________
From: Will Kerr <[email protected]>
To: "[email protected]" <[email protected]>
Sent: Friday, 24 February 2017, 6:49
Subject: ath10k - spectral scan - and - channel change
Hello, I searched the mail archives but couldn't find a clue to my question so here it is:
Im interested in performing a spectral scan of as much of the spectrum as possible, and quickly. this means scanning a channel for some time, changing channels, and repeating.
Background: when configuring an ath9k radio to Monitor mode, it is possible to do 2 things:
1) change wifi channel via command line, e.g. iw dev wlan1 set channel 3. This does it seemingly quickly, without taking down the interface (good)
2) control the debugfs files like /sys/kernel/debug/ieee80211/phy1/ath9k/spectral_scan_ctl (good)
The problem is:
ath10k, in Monitor mode, I am only able to change channels - 1) iw dev wlan0 set channel 104, but not access the debugfs files 2) (which is essential to control and obtain the spectral scan result) the error I get is:
root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device
ath10k, in AP mode, The opposite occurs - I am only able to access debugfs files 2) , but not change channel 1), which is annoying because I cant then scan the entire possible range.
the error I get is one of:
root@OpenWrt:~# iw dev wlan0 set channel 112
command failed: Device or resource busy (-16)
or
root@OpenWrt:~# iw dev wlan0 set channel 104 command failed: Invalid argument (-22)
Is there anything I can do to get both working?
Thanks. Will
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Thank you for looking into this.. I'm really sorry for the confusion, my second email reversed what the problem really is. Now clarified **below**:
Is it possible to control spectral_scan_ctl whilst in **Monitor mode**? my result:
root at OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
ash: write error: No such device
or
change channel whilst in **AP mode**?
my result:
root at OpenWrt:~# iw dev wlan0 set channel 112
command failed: Device or resource busy (-16)
and to your questions:
(1)
following https://wireless.wiki.kernel.org/en/users/drivers/ath10k/spectral - yes, I am able to obtain the spectral_scan0 data OK whilst in AP mode (although I was not able to do root@OpenWrt:~# iw dev wlan0 scan .. command failed: Device or resource busy (-16), I dont know why, I was still able to get scan data OK)
(2)
I get the same result for the below 3 commands if its set to AP mode, Monitor mode, or off (according to the setup in openWRT). I'm sorry, I dont know if there are more commands I should try to confirm things..
root@OpenWrt:~# iw phy0 info Wiphy phy0 max # scan SSIDs: 16 max scan IEs length: 199 bytes Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Device supports AP-side u-APSD. Available Antennas: TX 0x7 RX 0x7 Configured Antennas: TX 0x7 RX 0x7 Supported interface modes: * managed * AP * AP/VLAN * monitor ... ... ... (plus more, that I removed )
root@OpenWrt:~# dmesg | grep phy0 root@OpenWrt:~#
root@OpenWrt:~# ls /sys/kernel/debug/ieee80211/phy0/ath10k/spectral* /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_bins /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_count /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
Thank you, Will
----- Forwarded Message -----
From: "Shajakhan, Mohammed Shafi (Mohammed Shafi)" <[email protected]>
To: "[email protected]" <[email protected]>; Will Kerr <[email protected]>
Sent: Monday, 6 March 2017, 18:15
Subject: Re: ath10k - spectral scan - and - channel change
please follow
https://wireless.wiki.kernel.org/en/users/drivers/ath10k/spectral
please check if phy0 does exists ?
________________________________________
From: ath10k <[email protected]> on behalf of Will Kerr <[email protected]>
Sent: 06 March 2017 22:27
To: [email protected]
Subject: Re: ath10k - spectral scan - and - channel change
pinging and compacting the Q just in case the experts have an idea on this..
Is it possible to control spectral_scan_ctl whilst in AP mode? my result:
root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device
or
change channel whilst in Monitor mode?
my result:
root@OpenWrt:~# iw dev wlan0 set channel 112 command failed: Device or resource busy (-16)
Thanks Will.
________________________________
From: Will Kerr <[email protected]>
To: "[email protected]" <[email protected]>
Sent: Friday, 24 February 2017, 6:49
Subject: ath10k - spectral scan - and - channel change
Hello, I searched the mail archives but couldn't find a clue to my question so here it is:
Im interested in performing a spectral scan of as much of the spectrum as possible, and quickly. this means scanning a channel for some time, changing channels, and repeating.
Background: when configuring an ath9k radio to Monitor mode, it is possible to do 2 things:
1) change wifi channel via command line, e.g. iw dev wlan1 set channel 3. This does it seemingly quickly, without taking down the interface (good)
2) control the debugfs files like /sys/kernel/debug/ieee80211/phy1/ath9k/spectral_scan_ctl (good)
The problem is:
ath10k, in Monitor mode, I am only able to change channels - 1) iw dev wlan0 set channel 104, but not access the debugfs files 2) (which is essential to control and obtain the spectral scan result) the error I get is:
root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device
ath10k, in AP mode, The opposite occurs - I am only able to access debugfs files 2) , but not change channel 1), which is annoying because I cant then scan the entire possible range.
the error I get is one of:
root@OpenWrt:~# iw dev wlan0 set channel 112
command failed: Device or resource busy (-16)
or
root@OpenWrt:~# iw dev wlan0 set channel 104 command failed: Invalid argument (-22)
Is there anything I can do to get both working?
Thanks. Will
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
A message that is not in the archive (sent off-list or not yet received): [email protected]
p.s. I am looking to do both commands whilst in a single mode (AP, monitor, I dont really mind).
Thanks
________________________________
From: Will Kerr <[email protected]>
To: "[email protected]" <[email protected]>
Sent: Tuesday, 7 March 2017, 10:37
Subject: Fw: ath10k - spectral scan - and - channel change
Thank you for looking into this.. I'm really sorry for the confusion, my second email reversed what the problem really is. Now clarified **below**:
Is it possible to control spectral_scan_ctl whilst in **Monitor mode**? my result:
root at OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
ash: write error: No such device
or
change channel whilst in **AP mode**?
my result:
root at OpenWrt:~# iw dev wlan0 set channel 112
command failed: Device or resource busy (-16)
and to your questions:
(1)
following https://wireless.wiki.kernel.org/en/users/drivers/ath10k/spectral - yes, I am able to obtain the spectral_scan0 data OK whilst in AP mode (although I was not able to do root@OpenWrt:~# iw dev wlan0 scan .. command failed: Device or resource busy (-16), I dont know why, I was still able to get scan data OK)
(2)
I get the same result for the below 3 commands if its set to AP mode, Monitor mode, or off (according to the setup in openWRT). I'm sorry, I dont know if there are more commands I should try to confirm things..
root@OpenWrt:~# iw phy0 info Wiphy phy0 max # scan SSIDs: 16 max scan IEs length: 199 bytes Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Device supports AP-side u-APSD. Available Antennas: TX 0x7 RX 0x7 Configured Antennas: TX 0x7 RX 0x7 Supported interface modes: * managed * AP * AP/VLAN * monitor ... ... ... (plus more, that I removed )
root@OpenWrt:~# dmesg | grep phy0 root@OpenWrt:~#
root@OpenWrt:~# ls /sys/kernel/debug/ieee80211/phy0/ath10k/spectral* /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_bins /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_count /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
Thank you, Will
----- Forwarded Message -----
From: "Shajakhan, Mohammed Shafi (Mohammed Shafi)" <[email protected]>
To: "[email protected]" <[email protected]>; Will Kerr <[email protected]>
Sent: Monday, 6 March 2017, 18:15
Subject: Re: ath10k - spectral scan - and - channel change
please follow
https://wireless.wiki.kernel.org/en/users/drivers/ath10k/spectral
please check if phy0 does exists ?
________________________________________
From: ath10k <[email protected]> on behalf of Will Kerr <[email protected]>
Sent: 06 March 2017 22:27
To: [email protected]
Subject: Re: ath10k - spectral scan - and - channel change
pinging and compacting the Q just in case the experts have an idea on this..
Is it possible to control spectral_scan_ctl whilst in AP mode? my result:
root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device
or
change channel whilst in Monitor mode?
my result:
root@OpenWrt:~# iw dev wlan0 set channel 112 command failed: Device or resource busy (-16)
Thanks Will.
________________________________
From: Will Kerr <[email protected]>
To: "[email protected]" <[email protected]>
Sent: Friday, 24 February 2017, 6:49
Subject: ath10k - spectral scan - and - channel change
Hello, I searched the mail archives but couldn't find a clue to my question so here it is:
Im interested in performing a spectral scan of as much of the spectrum as possible, and quickly. this means scanning a channel for some time, changing channels, and repeating.
Background: when configuring an ath9k radio to Monitor mode, it is possible to do 2 things:
1) change wifi channel via command line, e.g. iw dev wlan1 set channel 3. This does it seemingly quickly, without taking down the interface (good)
2) control the debugfs files like /sys/kernel/debug/ieee80211/phy1/ath9k/spectral_scan_ctl (good)
The problem is:
ath10k, in Monitor mode, I am only able to change channels - 1) iw dev wlan0 set channel 104, but not access the debugfs files 2) (which is essential to control and obtain the spectral scan result) the error I get is:
root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device
ath10k, in AP mode, The opposite occurs - I am only able to access debugfs files 2) , but not change channel 1), which is annoying because I cant then scan the entire possible range.
the error I get is one of:
root@OpenWrt:~# iw dev wlan0 set channel 112
command failed: Device or resource busy (-16)
or
root@OpenWrt:~# iw dev wlan0 set channel 104 command failed: Invalid argument (-22)
Is there anything I can do to get both working?
Thanks. Will
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Quoted 7 lines
Thank you for looking into this.. I'm really sorry for the confusion, my second email reversed what the problem really is. Now clarified **below**:
Is it possible to control
spectral_scan_ctlwhilst in **Monitor mode**? my result:root at OpenWrt:~# echo disable >
/sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
ash: write error: No such device
[shafi] hmmm interesting .. looks like you need to bring the interface up, before doing this, the WMI command may respond error
Quoted 8 lines
or
change channel whilst in **AP mode**?
my result:root at OpenWrt:~# iw dev wlan0 set channel 112
command failed: Device or resource busy (-16)
[shafi] again you need to bring the interface up and also check if this channel is not disabled
iw phy0 info
Quoted 6 lines
and to your questions:
(1)
following https://wireless.wiki.kernel.org/en/users/drivers/ath10k/spectral - yes, I am able to obtain thespectral_scan0data OK whilst in AP mode (although I was not able to do root@OpenWrt:~# iw dev wlan0 scan .. command failed: Device or resource busy (-16), I dont know why, I was still able to get scan data OK)
[shafi] just check 'ap-force' is supported (or) not
Quoted 3 lines
(2)
I get the same result for the below 3 commands if its set to AP mode, Monitor mode, or off (according to the setup in openWRT). I'm sorry, I dont know if there are more commands I should try to confirm things..
[shafi] i have not tried in monitor i can give a try some time .. you can fine tune the below script ...
before sending spectral commands
1. make sure the interface is up
2. the channel is properly set
3. the mode is properly set
4. in AP mode 'ap-force' scan option is used ..
set -x
echo 0x2 > /sys/module/ath10k_core/parameters/debug_mask dmesg -n8
echo "=========================================="
echo "Dumping existing spectral scan data"
sleep 1
cat /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctl cat /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_bins cat /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_count
sleep 3
spectral_bin=$1
spectral_count=$2
ifconfig wlan1 up
sleep 2
echo $spectral_bin > /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_bins echo $spectral_count > /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_count echo manual > /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctl echo trigger > /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctl iw dev wlan1 scan ap-force
sleep 1
cp /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan0 /tmp/sample-$spectral_bin.fft
echo disable > /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctl
sleep 2
ls -lart /tmp/sample**
set +x
Quoted 128 lines
root@OpenWrt:~# iw phy0 info Wiphy phy0 max # scan SSIDs: 16 max scan IEs length: 199 bytes Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Device supports AP-side u-APSD. Available Antennas: TX 0x7 RX 0x7 Configured Antennas: TX 0x7 RX 0x7 Supported interface modes: * managed * AP * AP/VLAN * monitor ... ... ... (plus more, that I removed )root@OpenWrt:~# dmesg | grep phy0 root@OpenWrt:~#root@OpenWrt:~# ls /sys/kernel/debug/ieee80211/phy0/ath10k/spectral* /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_bins /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_count /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctlThank you, Will
----- Forwarded Message -----
From: "Shajakhan, Mohammed Shafi (Mohammed Shafi)" <[email protected]>
To: "[email protected]" <[email protected]>; Will Kerr <[email protected]>
Sent: Monday, 6 March 2017, 18:15
Subject: Re: ath10k - spectral scan - and - channel changeplease follow
https://wireless.wiki.kernel.org/en/users/drivers/ath10k/spectralplease check if phy0 does exists ?
________________________________________
From: ath10k <[email protected]> on behalf of Will Kerr <[email protected]>
Sent: 06 March 2017 22:27
To: [email protected]
Subject: Re: ath10k - spectral scan - and - channel changepinging and compacting the Q just in case the experts have an idea on this..
Is it possible to control
spectral_scan_ctlwhilst in AP mode? my result:root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such deviceor
change channel whilst in Monitor mode?
my result:root@OpenWrt:~# iw dev wlan0 set channel 112 command failed: Device or resource busy (-16)Thanks Will.
________________________________
From: Will Kerr <[email protected]>
To: "[email protected]" <[email protected]>
Sent: Friday, 24 February 2017, 6:49
Subject: ath10k - spectral scan - and - channel changeHello, I searched the mail archives but couldn't find a clue to my question so here it is:
Im interested in performing a spectral scan of as much of the spectrum as possible, and quickly. this means scanning a channel for some time, changing channels, and repeating.
Background: when configuring an ath9k radio to Monitor mode, it is possible to do 2 things:
1) change wifi channel via command line, e.g. iw dev wlan1 set channel 3. This does it seemingly quickly, without taking down the interface (good)
2) control the debugfs files like
/sys/kernel/debug/ieee80211/phy1/ath9k/spectral_scan_ctl(good)The problem is:
ath10k, in Monitor mode, I am only able to change channels - 1) iw dev wlan0 set channel 104, but not access the debugfs files 2) (which is essential to control and obtain the spectral scan result) the error I get is:
root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such deviceath10k, in AP mode, The opposite occurs - I am only able to access debugfs files 2) , but not change channel 1), which is annoying because I cant then scan the entire possible range.
the error I get is one of:
root@OpenWrt:~# iw dev wlan0 set channel 112command failed: Device or resource busy (-16)
orroot@OpenWrt:~# iw dev wlan0 set channel 104 command failed: Invalid argument (-22)Is there anything I can do to get both working?
Thanks. Will
_______________________________________________
ath10k mailing list
Quoted 7 lines
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Quoted 2 lines
[shafi] hmmm interesting .. looks like you need to bring the interface up, before doing this, the WMI command may respond error
I thought it was, at least now when I try:
AP mode:
(its OK)
Monitor Mode:
root@OpenWrt:~# ifconfig wlan0 up root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device
Quoted 1 line
iw phy0 info
* 5560 MHz [112] (24.0 dBm) (no IR, radar detection) DFS state: usable (for 4036 sec)
Quoted 1 line
shafi] just check 'ap-force' is supported (or) not
I dont think it is supported on my ArcherC7 openWRT for some reason:
AP mode:
root@OpenWrt:~# ifconfig wlan0 up root@OpenWrt:~# iw wlan0 scan command failed: Device or resource busy (-16) root@OpenWrt:~# iw wlan0 scan ap-force command failed: Device or resource busy (-16)
Monitor Mode:
root@OpenWrt:~# ifconfig wlan0 up root@OpenWrt:~# iw wlan0 scan command failed: Operation not supported (-122) root@OpenWrt:~# iw wlan0 scan ap-force command failed: Operation not supported (-122)
Quoted 1 line
[shafi] i have not tried in monitor i can give a try some time ..
That would be great, if you could confirm my problem.. e.g. in Monitor Mode:
root@OpenWrt:~# ifconfig wlan0 up root@OpenWrt:~# echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device root@OpenWrt:~# echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: Invalid argument root@OpenWrt:~# cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl disableroot@OpenWrt:~#
Quoted 1 line
you can fine tune the below script ...
I ran it, and it fails on the iw wlan0 scan ap-force part ... (...)
+ iw dev wlan0 scan ap-force
command failed: Device or resource busy (-16)
(...)
The reason I am trying to do both (control spectral_scan_ctl and change channels) is because it works fine in ath9k monitor mode..
Thanks again.
----- Original Message -----
From: Mohammed Shafi Shajakhan <[email protected]>
To: Will Kerr <[email protected]>
Cc: "[email protected]" <[email protected]>; Shajakhan Mohammed Shafi (Mohammed Shafi) <[email protected]>
Sent: Tuesday, 14 March 2017, 16:23
Subject: Re: ath10k - spectral scan - and - channel change
Quoted 7 lines
Thank you for looking into this.. I'm really sorry for the confusion, my second email reversed what the problem really is. Now clarified **below**:
Is it possible to control
spectral_scan_ctlwhilst in **Monitor mode**? my result:root at OpenWrt:~# echo disable >
/sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
ash: write error: No such device
[shafi] hmmm interesting .. looks like you need to bring the interface up, before doing this, the WMI command may respond error
Quoted 8 lines
or
change channel whilst in **AP mode**?
my result:root at OpenWrt:~# iw dev wlan0 set channel 112
command failed: Device or resource busy (-16)
[shafi] again you need to bring the interface up and also check if this channel is not disabled
iw phy0 info
Quoted 6 lines
and to your questions:
(1)
following https://wireless.wiki.kernel.org/en/users/drivers/ath10k/spectral - yes, I am able to obtain thespectral_scan0data OK whilst in AP mode (although I was not able to do root@OpenWrt:~# iw dev wlan0 scan .. command failed: Device or resource busy (-16), I dont know why, I was still able to get scan data OK)
[shafi] just check 'ap-force' is supported (or) not
Quoted 3 lines
(2)
I get the same result for the below 3 commands if its set to AP mode, Monitor mode, or off (according to the setup in openWRT). I'm sorry, I dont know if there are more commands I should try to confirm things..
[shafi] i have not tried in monitor i can give a try some time .. you can fine tune the below script ...
before sending spectral commands
1. make sure the interface is up
2. the channel is properly set
3. the mode is properly set
4. in AP mode 'ap-force' scan option is used ..
set -x
echo 0x2 > /sys/module/ath10k_core/parameters/debug_mask dmesg -n8
echo "=========================================="
echo "Dumping existing spectral scan data"
sleep 1
cat /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctl cat /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_bins cat /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_count
sleep 3
spectral_bin=$1
spectral_count=$2
ifconfig wlan1 up
sleep 2
echo $spectral_bin > /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_bins echo $spectral_count > /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_count echo manual > /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctl echo trigger > /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctl iw dev wlan1 scan ap-force
sleep 1
cp /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan0 /tmp/sample-$spectral_bin.fft
echo disable > /sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctl
sleep 2
ls -lart /tmp/sample**
set +x
Quoted 128 lines
root@OpenWrt:~# iw phy0 info Wiphy phy0 max # scan SSIDs: 16 max scan IEs length: 199 bytes Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Device supports AP-side u-APSD. Available Antennas: TX 0x7 RX 0x7 Configured Antennas: TX 0x7 RX 0x7 Supported interface modes: * managed * AP * AP/VLAN * monitor ... ... ... (plus more, that I removed )root@OpenWrt:~# dmesg | grep phy0 root@OpenWrt:~#root@OpenWrt:~# ls /sys/kernel/debug/ieee80211/phy0/ath10k/spectral* /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_bins /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_count /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctlThank you, Will
----- Forwarded Message -----
From: "Shajakhan, Mohammed Shafi (Mohammed Shafi)" <[email protected]>
To: "[email protected]" <[email protected]>; Will Kerr <[email protected]>
Sent: Monday, 6 March 2017, 18:15
Subject: Re: ath10k - spectral scan - and - channel changeplease follow
https://wireless.wiki.kernel.org/en/users/drivers/ath10k/spectralplease check if phy0 does exists ?
________________________________________
From: ath10k <[email protected]> on behalf of Will Kerr <[email protected]>
Sent: 06 March 2017 22:27
To: [email protected]
Subject: Re: ath10k - spectral scan - and - channel changepinging and compacting the Q just in case the experts have an idea on this..
Is it possible to control
spectral_scan_ctlwhilst in AP mode? my result:root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such deviceor
change channel whilst in Monitor mode?
my result:root@OpenWrt:~# iw dev wlan0 set channel 112 command failed: Device or resource busy (-16)Thanks Will.
________________________________
From: Will Kerr <[email protected]>
To: "[email protected]" <[email protected]>
Sent: Friday, 24 February 2017, 6:49
Subject: ath10k - spectral scan - and - channel changeHello, I searched the mail archives but couldn't find a clue to my question so here it is:
Im interested in performing a spectral scan of as much of the spectrum as possible, and quickly. this means scanning a channel for some time, changing channels, and repeating.
Background: when configuring an ath9k radio to Monitor mode, it is possible to do 2 things:
1) change wifi channel via command line, e.g. iw dev wlan1 set channel 3. This does it seemingly quickly, without taking down the interface (good)
2) control the debugfs files like
/sys/kernel/debug/ieee80211/phy1/ath9k/spectral_scan_ctl(good)The problem is:
ath10k, in Monitor mode, I am only able to change channels - 1) iw dev wlan0 set channel 104, but not access the debugfs files 2) (which is essential to control and obtain the spectral scan result) the error I get is:
root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such deviceath10k, in AP mode, The opposite occurs - I am only able to access debugfs files 2) , but not change channel 1), which is annoying because I cant then scan the entire possible range.
the error I get is one of:
root@OpenWrt:~# iw dev wlan0 set channel 112command failed: Device or resource busy (-16)
orroot@OpenWrt:~# iw dev wlan0 set channel 104 command failed: Invalid argument (-22)Is there anything I can do to get both working?
Thanks. Will
_______________________________________________
ath10k mailing list
Quoted 8 lines
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Quoted 5 lines · Will Kerr
Quoted 2 lines
[shafi] hmmm interesting .. looks like you need to bring the interface up, before doing this, the WMI command may respond error
I thought it was, at least now when I try:
Quoted 7 lines
AP mode:
(its OK)Monitor Mode:
root@OpenWrt:~# ifconfig wlan0 up root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device
[shafi] may sound dumb (need to check), first cd to cd /sys/kernel/debug/ieee80211/phy0/ath10k echo disable > spectral_scan_ctl
Quoted 19 lines
Quoted 4 lines
iw phy0 info
* 5560 MHz [112] (24.0 dBm) (no IR, radar detection) DFS state: usable (for 4036 sec)
Quoted 1 line
shafi] just check 'ap-force' is supported (or) not
I dont think it is supported on my ArcherC7 openWRT for some reason:
AP mode:root@OpenWrt:~# ifconfig wlan0 up root@OpenWrt:~# iw wlan0 scan command failed: Device or resource busy (-16) root@OpenWrt:~# iw wlan0 scan ap-force command failed: Device or resource busy (-16)
Quoted 7 lines
Monitor Mode:
root@OpenWrt:~# ifconfig wlan0 up root@OpenWrt:~# iw wlan0 scan command failed: Operation not supported (-122) root@OpenWrt:~# iw wlan0 scan ap-force command failed: Operation not supported (-122)
[shafi] good to see if you have latest hostapd and ath10k backports
Quoted 25 lines
Quoted 2 lines
[shafi] i have not tried in monitor i can give a try some time ..
That would be great, if you could confirm my problem.. e.g. in Monitor Mode:
root@OpenWrt:~# ifconfig wlan0 up root@OpenWrt:~# echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device root@OpenWrt:~# echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: Invalid argument root@OpenWrt:~# cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl disableroot@OpenWrt:~#Quoted 1 line
you can fine tune the below script ...
I ran it, and it fails on the iw wlan0 scan ap-force part ... (...)
+ iw dev wlan0 scan ap-force
command failed: Device or resource busy (-16)
(...)
Quoted 3 lines
The reason I am trying to do both (control
spectral_scan_ctland change channels) is because it works fine in ath9k monitor mode..
[shafi] ok, we can check that , i think for ath9k the complete support is in driver (no firmware)
Quoted 88 lines
----- Original Message -----
From: Mohammed Shafi Shajakhan <[email protected]>
To: Will Kerr <[email protected]>
Cc: "[email protected]" <[email protected]>; Shajakhan Mohammed Shafi (Mohammed Shafi) <[email protected]>
Sent: Tuesday, 14 March 2017, 16:23
Subject: Re: ath10k - spectral scan - and - channel changeQuoted 7 lines
Thank you for looking into this.. I'm really sorry for the confusion, my second email reversed what the problem really is. Now clarified **below**:
Is it possible to control
spectral_scan_ctlwhilst in **Monitor mode**? my result:root at OpenWrt:~# echo disable >
/sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
ash: write error: No such device[shafi] hmmm interesting .. looks like you need to bring the interface up, before doing this, the WMI command may respond error
Quoted 8 lines
or
change channel whilst in **AP mode**?
my result:root at OpenWrt:~# iw dev wlan0 set channel 112
command failed: Device or resource busy (-16)[shafi] again you need to bring the interface up and also check if this channel is not disabled
iw phy0 info
Quoted 6 lines
and to your questions:
(1)
following https://wireless.wiki.kernel.org/en/users/drivers/ath10k/spectral - yes, I am able to obtain thespectral_scan0data OK whilst in AP mode (although I was not able to do root@OpenWrt:~# iw dev wlan0 scan .. command failed: Device or resource busy (-16), I dont know why, I was still able to get scan data OK)[shafi] just check 'ap-force' is supported (or) not
Quoted 3 lines
(2)
I get the same result for the below 3 commands if its set to AP mode, Monitor mode, or off (according to the setup in openWRT). I'm sorry, I dont know if there are more commands I should try to confirm things..[shafi] i have not tried in monitor i can give a try some time .. you can fine tune the below script ...
before sending spectral commands1. make sure the interface is up
2. the channel is properly set
3. the mode is properly set
4. in AP mode 'ap-force' scan option is used ..set -x
echo
0x2>/sys/module/ath10k_core/parameters/debug_maskdmesg -n8echo "=========================================="
echo "Dumping existing spectral scan data"
sleep 1cat
/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctlcat/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_binscat/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_countsleep 3
spectral_bin=$1
spectral_count=$2
ifconfig wlan1 up
sleep 2
echo $spectral_bin >/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_binsecho $spectral_count >/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_countecho manual >/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctlecho trigger >/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctliw dev wlan1 scan ap-force
sleep 1
cp/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan0/tmp/sample-$spectral_bin.fft
echo disable >/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctl
Quoted 142 lines
sleep 2
ls -lart/tmp/sample**
set +xQuoted 136 lines
root@OpenWrt:~# iw phy0 info Wiphy phy0 max # scan SSIDs: 16 max scan IEs length: 199 bytes Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Device supports AP-side u-APSD. Available Antennas: TX 0x7 RX 0x7 Configured Antennas: TX 0x7 RX 0x7 Supported interface modes: * managed * AP * AP/VLAN * monitor ... ... ... (plus more, that I removed )root@OpenWrt:~# dmesg | grep phy0 root@OpenWrt:~#root@OpenWrt:~# ls /sys/kernel/debug/ieee80211/phy0/ath10k/spectral* /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_bins /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_count /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctlThank you, Will
----- Forwarded Message -----
From: "Shajakhan, Mohammed Shafi (Mohammed Shafi)" <[email protected]>
To: "[email protected]" <[email protected]>; Will Kerr <[email protected]>
Sent: Monday, 6 March 2017, 18:15
Subject: Re: ath10k - spectral scan - and - channel changeplease follow
https://wireless.wiki.kernel.org/en/users/drivers/ath10k/spectralplease check if phy0 does exists ?
________________________________________
From: ath10k <[email protected]> on behalf of Will Kerr <[email protected]>
Sent: 06 March 2017 22:27
To: [email protected]
Subject: Re: ath10k - spectral scan - and - channel changepinging and compacting the Q just in case the experts have an idea on this..
Is it possible to control
spectral_scan_ctlwhilst in AP mode? my result:root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such deviceor
change channel whilst in Monitor mode?
my result:root@OpenWrt:~# iw dev wlan0 set channel 112 command failed: Device or resource busy (-16)Thanks Will.
________________________________
From: Will Kerr <[email protected]>
To: "[email protected]" <[email protected]>
Sent: Friday, 24 February 2017, 6:49
Subject: ath10k - spectral scan - and - channel changeHello, I searched the mail archives but couldn't find a clue to my question so here it is:
Im interested in performing a spectral scan of as much of the spectrum as possible, and quickly. this means scanning a channel for some time, changing channels, and repeating.
Background: when configuring an ath9k radio to Monitor mode, it is possible to do 2 things:
1) change wifi channel via command line, e.g. iw dev wlan1 set channel 3. This does it seemingly quickly, without taking down the interface (good)
2) control the debugfs files like
/sys/kernel/debug/ieee80211/phy1/ath9k/spectral_scan_ctl(good)The problem is:
ath10k, in Monitor mode, I am only able to change channels - 1) iw dev wlan0 set channel 104, but not access the debugfs files 2) (which is essential to control and obtain the spectral scan result) the error I get is:
root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such deviceath10k, in AP mode, The opposite occurs - I am only able to access debugfs files 2) , but not change channel 1), which is annoying because I cant then scan the entire possible range.
the error I get is one of:
root@OpenWrt:~# iw dev wlan0 set channel 112command failed: Device or resource busy (-16)
orroot@OpenWrt:~# iw dev wlan0 set channel 104 command failed: Invalid argument (-22)Is there anything I can do to get both working?
Thanks. Will
_______________________________________________
ath10k mailing list[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
not dumb at all - I started to try most things, here what happens when I tried it:
root@OpenWrt:~# cd /sys/kernel/debug/ieee80211/phy0/ath10k/ root@OpenWrt:/sys/kernel/debug/ieee80211/phy0/ath10k# echo disable > spectral_scan_ctl ash: write error: No such device root@OpenWrt:/sys/kernel/debug/ieee80211/phy0/ath10k#
Quoted 1 line
[shafi] good to see if you have latest hostapd and ath10k backports
are these the right commands / what you would expect? ( I notice no mention of ath10k in lsmod)
root@OpenWrt:~# hostapd -v hostapd v2.5-devel User space daemon for IEEE 802.11 AP management, IEEE 802.1X/WPA/WPA2/EAP/RADIUS Authenticator Copyright (c) 2002-2015, Jouni Malinen <[email protected]> and contributors
root@OpenWrt:~# lsmod | grep compat compat 1120 5 ath9k
root@OpenWrt:~# dmesg | grep backport [ 11.800000] Loading modules backported from Linux version master-2015-03-09-0-g141f155 [ 11.810000] Backport generated by backports.git backports-20150129-0-gdd4a670 root@OpenWrt:~#
Quoted 1 line
[shafi] ok, we can check that , i think for ath9k the complete support is in
driver (no firmware)
OK thanks,
________________________________
From: Mohammed Shafi Shajakhan <[email protected]>
To: Will Kerr <[email protected]>
Cc: "[email protected]" <[email protected]>; Shajakhan Mohammed Shafi (Mohammed Shafi) <[email protected]>
Sent: Wednesday, 15 March 2017, 11:26
Subject: Re: ath10k - spectral scan - and - channel change
Quoted 5 lines · Will Kerr
Quoted 2 lines
[shafi] hmmm interesting .. looks like you need to bring the interface up, before doing this, the WMI command may respond error
I thought it was, at least now when I try:
Quoted 7 lines
AP mode:
(its OK)Monitor Mode:
root@OpenWrt:~# ifconfig wlan0 up root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device
[shafi] may sound dumb (need to check), first cd to cd /sys/kernel/debug/ieee80211/phy0/ath10k echo disable > spectral_scan_ctl
Quoted 19 lines
Quoted 4 lines
iw phy0 info
* 5560 MHz [112] (24.0 dBm) (no IR, radar detection) DFS state: usable (for 4036 sec)
Quoted 1 line
shafi] just check 'ap-force' is supported (or) not
I dont think it is supported on my ArcherC7 openWRT for some reason:
AP mode:root@OpenWrt:~# ifconfig wlan0 up root@OpenWrt:~# iw wlan0 scan command failed: Device or resource busy (-16) root@OpenWrt:~# iw wlan0 scan ap-force command failed: Device or resource busy (-16)
Quoted 7 lines
Monitor Mode:
root@OpenWrt:~# ifconfig wlan0 up root@OpenWrt:~# iw wlan0 scan command failed: Operation not supported (-122) root@OpenWrt:~# iw wlan0 scan ap-force command failed: Operation not supported (-122)
[shafi] good to see if you have latest hostapd and ath10k backports
Quoted 25 lines
Quoted 2 lines
[shafi] i have not tried in monitor i can give a try some time ..
That would be great, if you could confirm my problem.. e.g. in Monitor Mode:
root@OpenWrt:~# ifconfig wlan0 up root@OpenWrt:~# echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such device root@OpenWrt:~# echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: Invalid argument root@OpenWrt:~# cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl disableroot@OpenWrt:~#Quoted 1 line
you can fine tune the below script ...
I ran it, and it fails on the iw wlan0 scan ap-force part ... (...)
+ iw dev wlan0 scan ap-force
command failed: Device or resource busy (-16)
(...)
Quoted 3 lines
The reason I am trying to do both (control
spectral_scan_ctland change channels) is because it works fine in ath9k monitor mode..
[shafi] ok, we can check that , i think for ath9k the complete support is in driver (no firmware)
Quoted 88 lines
----- Original Message -----
From: Mohammed Shafi Shajakhan <[email protected]>
To: Will Kerr <[email protected]>
Cc: "[email protected]" <[email protected]>; Shajakhan Mohammed Shafi (Mohammed Shafi) <[email protected]>
Sent: Tuesday, 14 March 2017, 16:23
Subject: Re: ath10k - spectral scan - and - channel changeQuoted 7 lines
Thank you for looking into this.. I'm really sorry for the confusion, my second email reversed what the problem really is. Now clarified **below**:
Is it possible to control
spectral_scan_ctlwhilst in **Monitor mode**? my result:root at OpenWrt:~# echo disable >
/sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
ash: write error: No such device[shafi] hmmm interesting .. looks like you need to bring the interface up, before doing this, the WMI command may respond error
Quoted 8 lines
or
change channel whilst in **AP mode**?
my result:root at OpenWrt:~# iw dev wlan0 set channel 112
command failed: Device or resource busy (-16)[shafi] again you need to bring the interface up and also check if this channel is not disabled
iw phy0 info
Quoted 6 lines
and to your questions:
(1)
following https://wireless.wiki.kernel.org/en/users/drivers/ath10k/spectral - yes, I am able to obtain thespectral_scan0data OK whilst in AP mode (although I was not able to do root@OpenWrt:~# iw dev wlan0 scan .. command failed: Device or resource busy (-16), I dont know why, I was still able to get scan data OK)[shafi] just check 'ap-force' is supported (or) not
Quoted 3 lines
(2)
I get the same result for the below 3 commands if its set to AP mode, Monitor mode, or off (according to the setup in openWRT). I'm sorry, I dont know if there are more commands I should try to confirm things..[shafi] i have not tried in monitor i can give a try some time .. you can fine tune the below script ...
before sending spectral commands1. make sure the interface is up
2. the channel is properly set
3. the mode is properly set
4. in AP mode 'ap-force' scan option is used ..set -x
echo
0x2>/sys/module/ath10k_core/parameters/debug_maskdmesg -n8echo "=========================================="
echo "Dumping existing spectral scan data"
sleep 1cat
/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctlcat/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_binscat/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_countsleep 3
spectral_bin=$1
spectral_count=$2
ifconfig wlan1 up
sleep 2
echo $spectral_bin >/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_binsecho $spectral_count >/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_countecho manual >/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctlecho trigger >/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctliw dev wlan1 scan ap-force
sleep 1
cp/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan0/tmp/sample-$spectral_bin.fft
echo disable >/sys/kernel/debug/ieee80211/phy1/ath10k/spectral_scan_ctl
Quoted 142 lines
sleep 2
ls -lart/tmp/sample**
set +xQuoted 136 lines
root@OpenWrt:~# iw phy0 info Wiphy phy0 max # scan SSIDs: 16 max scan IEs length: 199 bytes Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Device supports AP-side u-APSD. Available Antennas: TX 0x7 RX 0x7 Configured Antennas: TX 0x7 RX 0x7 Supported interface modes: * managed * AP * AP/VLAN * monitor ... ... ... (plus more, that I removed )root@OpenWrt:~# dmesg | grep phy0 root@OpenWrt:~#root@OpenWrt:~# ls /sys/kernel/debug/ieee80211/phy0/ath10k/spectral* /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_bins /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_count /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctlThank you, Will
----- Forwarded Message -----
From: "Shajakhan, Mohammed Shafi (Mohammed Shafi)" <[email protected]>
To: "[email protected]" <[email protected]>; Will Kerr <[email protected]>
Sent: Monday, 6 March 2017, 18:15
Subject: Re: ath10k - spectral scan - and - channel changeplease follow
https://wireless.wiki.kernel.org/en/users/drivers/ath10k/spectralplease check if phy0 does exists ?
________________________________________
From: ath10k <[email protected]> on behalf of Will Kerr <[email protected]>
Sent: 06 March 2017 22:27
To: [email protected]
Subject: Re: ath10k - spectral scan - and - channel changepinging and compacting the Q just in case the experts have an idea on this..
Is it possible to control
spectral_scan_ctlwhilst in AP mode? my result:root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such deviceor
change channel whilst in Monitor mode?
my result:root@OpenWrt:~# iw dev wlan0 set channel 112 command failed: Device or resource busy (-16)Thanks Will.
________________________________
From: Will Kerr <[email protected]>
To: "[email protected]" <[email protected]>
Sent: Friday, 24 February 2017, 6:49
Subject: ath10k - spectral scan - and - channel changeHello, I searched the mail archives but couldn't find a clue to my question so here it is:
Im interested in performing a spectral scan of as much of the spectrum as possible, and quickly. this means scanning a channel for some time, changing channels, and repeating.
Background: when configuring an ath9k radio to Monitor mode, it is possible to do 2 things:
1) change wifi channel via command line, e.g. iw dev wlan1 set channel 3. This does it seemingly quickly, without taking down the interface (good)
2) control the debugfs files like
/sys/kernel/debug/ieee80211/phy1/ath9k/spectral_scan_ctl(good)The problem is:
ath10k, in Monitor mode, I am only able to change channels - 1) iw dev wlan0 set channel 104, but not access the debugfs files 2) (which is essential to control and obtain the spectral scan result) the error I get is:
root@OpenWrt:~# echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl ash: write error: No such deviceath10k, in AP mode, The opposite occurs - I am only able to access debugfs files 2) , but not change channel 1), which is annoying because I cant then scan the entire possible range.
the error I get is one of:
root@OpenWrt:~# iw dev wlan0 set channel 112command failed: Device or resource busy (-16)
orroot@OpenWrt:~# iw dev wlan0 set channel 104 command failed: Invalid argument (-22)Is there anything I can do to get both working?
Thanks. Will
_______________________________________________
ath10k mailing list[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k