net: remove ax25 and amateur radio (hamradio) subsystem
Subsystems (10)
Jakub Kicinski
maintainerPATCH 1/1 net: remove ax25 and amateur radio (hamradio) subsystem
Remove the amateur radio (AX.25, NET/ROM, ROSE) protocol implementation and all associated hamradio device drivers from the kernel tree. This set of protocols has long been a huge bug/syzbot magnet, and since nobody stepped up to help us deal with the influx of the AI-generated bug reports we need to move it out of tree to protect our sanity.
The code is moved to an out-of-tree repo:
https://github.com/linux-netdev/mod-orphan
if it's cleaned up and reworked there we can accept it back.
Minimal stub headers are kept for include/net/ax25.h (AX25_P_IP, AX25_ADDR_LEN, ax25_address) and include/net/rose.h (ROSE_ADDR_LEN) so that the conditional integration code in arp.c and tun.c continues to compile and work when the out-of-tree modules are loaded.
---
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
--- MAINTAINERS | 73 - Documentation/.renames.txt | 2 - .../admin-guide/kernel-parameters.txt | 18 - Documentation/networking/6pack.rst | 191 -- Documentation/networking/ax25.rst | 17 - .../device_drivers/hamradio/baycom.rst | 174 -- .../device_drivers/hamradio/index.rst | 12 - .../device_drivers/hamradio/z8530drv.rst | 686 ------ .../networking/device_drivers/index.rst | 1 - Documentation/networking/index.rst | 2 - Documentation/staging/magic-number.rst | 3 - .../it_IT/staging/magic-number.rst | 3 - .../sp_SP/process/magic-number.rst | 3 - .../zh_CN/process/magic-number.rst | 3 - .../zh_TW/process/magic-number.rst | 3 - drivers/net/hamradio/Kconfig | 162 -- net/Kconfig | 1 - net/ax25/Kconfig | 108 - drivers/net/Makefile | 1 - drivers/net/hamradio/Makefile | 22 - net/Makefile | 3 - net/ax25/Makefile | 12 - net/netrom/Makefile | 10 - net/rose/Makefile | 10 - drivers/net/hamradio/z8530.h | 246 -- include/linux/hdlcdrv.h | 276 --- include/linux/netdevice.h | 5 +- include/linux/scc.h | 86 - include/linux/yam.h | 67 - include/net/ax25.h | 476 +--- include/net/netrom.h | 273 --- include/net/rose.h | 263 +- include/uapi/linux/baycom.h | 40 - include/uapi/linux/hdlcdrv.h | 111 - include/uapi/linux/netrom.h | 37 - include/uapi/linux/rose.h | 91 - include/uapi/linux/scc.h | 174 -- drivers/net/hamradio/6pack.c | 912 ------- drivers/net/hamradio/baycom_epp.c | 1316 ---------- drivers/net/hamradio/baycom_par.c | 598 ----- drivers/net/hamradio/baycom_ser_fdx.c | 678 ----- drivers/net/hamradio/baycom_ser_hdx.c | 727 ------ drivers/net/hamradio/bpqether.c | 593 ----- drivers/net/hamradio/hdlcdrv.c | 747 ------ drivers/net/hamradio/mkiss.c | 980 -------- drivers/net/hamradio/scc.c | 2179 ----------------- drivers/net/hamradio/yam.c | 1191 --------- net/ax25/af_ax25.c | 2089 ---------------- net/ax25/ax25_addr.c | 303 --- net/ax25/ax25_dev.c | 200 -- net/ax25/ax25_ds_in.c | 298 --- net/ax25/ax25_ds_subr.c | 204 -- net/ax25/ax25_ds_timer.c | 235 -- net/ax25/ax25_iface.c | 214 -- net/ax25/ax25_in.c | 455 ---- net/ax25/ax25_ip.c | 247 -- net/ax25/ax25_out.c | 398 --- net/ax25/ax25_route.c | 416 ---- net/ax25/ax25_std_in.c | 443 ---- net/ax25/ax25_std_subr.c | 83 - net/ax25/ax25_std_timer.c | 175 -- net/ax25/ax25_subr.c | 296 --- net/ax25/ax25_timer.c | 224 -- net/ax25/ax25_uid.c | 204 -- net/ax25/sysctl_net_ax25.c | 181 -- net/ipv4/arp.c | 1 - net/netrom/af_netrom.c | 1536 ------------ net/netrom/nr_dev.c | 178 -- net/netrom/nr_in.c | 301 --- net/netrom/nr_loopback.c | 73 - net/netrom/nr_out.c | 272 -- net/netrom/nr_route.c | 989 -------- net/netrom/nr_subr.c | 280 --- net/netrom/nr_timer.c | 249 -- net/netrom/sysctl_net_netrom.c | 156 -- net/rose/af_rose.c | 1687 ------------- net/rose/rose_dev.c | 141 -- net/rose/rose_in.c | 301 --- net/rose/rose_link.c | 289 --- net/rose/rose_loopback.c | 133 - net/rose/rose_out.c | 122 - net/rose/rose_route.c | 1333 ---------- net/rose/rose_subr.c | 556 ----- net/rose/rose_timer.c | 227 -- net/rose/sysctl_net_rose.c | 125 - arch/mips/configs/bcm47xx_defconfig | 1 - arch/mips/configs/bigsur_defconfig | 10 - arch/mips/configs/gpr_defconfig | 11 - arch/mips/configs/mtx1_defconfig | 11 - arch/mips/configs/rb532_defconfig | 1 - arch/mips/configs/rm200_defconfig | 7 - arch/mips/configs/rt305x_defconfig | 1 - arch/mips/configs/xway_defconfig | 1 - 93 files changed, 6 insertions(+), 29237 deletions(-) delete mode 100644 Documentation/networking/6pack.rst delete mode 100644 Documentation/networking/ax25.rst delete mode 100644 Documentation/networking/device_drivers/hamradio/baycom.rst delete mode 100644 Documentation/networking/device_drivers/hamradio/index.rst delete mode 100644 Documentation/networking/device_drivers/hamradio/z8530drv.rst delete mode 100644 drivers/net/hamradio/Kconfig delete mode 100644 net/ax25/Kconfig delete mode 100644 drivers/net/hamradio/Makefile delete mode 100644 net/ax25/Makefile delete mode 100644 net/netrom/Makefile delete mode 100644 net/rose/Makefile delete mode 100644 drivers/net/hamradio/z8530.h delete mode 100644 include/linux/hdlcdrv.h delete mode 100644 include/linux/scc.h delete mode 100644 include/linux/yam.h delete mode 100644 include/net/netrom.h delete mode 100644 include/uapi/linux/baycom.h delete mode 100644 include/uapi/linux/hdlcdrv.h delete mode 100644 include/uapi/linux/netrom.h delete mode 100644 include/uapi/linux/rose.h delete mode 100644 include/uapi/linux/scc.h delete mode 100644 drivers/net/hamradio/6pack.c delete mode 100644 drivers/net/hamradio/baycom_epp.c delete mode 100644 drivers/net/hamradio/baycom_par.c delete mode 100644 drivers/net/hamradio/baycom_ser_fdx.c delete mode 100644 drivers/net/hamradio/baycom_ser_hdx.c delete mode 100644 drivers/net/hamradio/bpqether.c delete mode 100644 drivers/net/hamradio/hdlcdrv.c delete mode 100644 drivers/net/hamradio/mkiss.c delete mode 100644 drivers/net/hamradio/scc.c delete mode 100644 drivers/net/hamradio/yam.c delete mode 100644 net/ax25/af_ax25.c delete mode 100644 net/ax25/ax25_addr.c delete mode 100644 net/ax25/ax25_dev.c delete mode 100644 net/ax25/ax25_ds_in.c delete mode 100644 net/ax25/ax25_ds_subr.c delete mode 100644 net/ax25/ax25_ds_timer.c delete mode 100644 net/ax25/ax25_iface.c delete mode 100644 net/ax25/ax25_in.c delete mode 100644 net/ax25/ax25_ip.c delete mode 100644 net/ax25/ax25_out.c delete mode 100644 net/ax25/ax25_route.c delete mode 100644 net/ax25/ax25_std_in.c delete mode 100644 net/ax25/ax25_std_subr.c delete mode 100644 net/ax25/ax25_std_timer.c delete mode 100644 net/ax25/ax25_subr.c delete mode 100644 net/ax25/ax25_timer.c delete mode 100644 net/ax25/ax25_uid.c delete mode 100644 net/ax25/sysctl_net_ax25.c delete mode 100644 net/netrom/af_netrom.c delete mode 100644 net/netrom/nr_dev.c delete mode 100644 net/netrom/nr_in.c delete mode 100644 net/netrom/nr_loopback.c delete mode 100644 net/netrom/nr_out.c delete mode 100644 net/netrom/nr_route.c delete mode 100644 net/netrom/nr_subr.c delete mode 100644 net/netrom/nr_timer.c delete mode 100644 net/netrom/sysctl_net_netrom.c delete mode 100644 net/rose/af_rose.c delete mode 100644 net/rose/rose_dev.c delete mode 100644 net/rose/rose_in.c delete mode 100644 net/rose/rose_link.c delete mode 100644 net/rose/rose_loopback.c delete mode 100644 net/rose/rose_out.c delete mode 100644 net/rose/rose_route.c delete mode 100644 net/rose/rose_subr.c delete mode 100644 net/rose/rose_timer.c delete mode 100644 net/rose/sysctl_net_rose.c
MAINTAINERS +0 -73
@@ -102,12 +102,6 @@ F: Documentation/networking/6lowpan.rst F: include/net/6lowpan.h F: net/6lowpan/ -6PACK NETWORK DRIVER FOR AX.25 -M: Andreas Koensgen <[email protected]> -L: [email protected] -S: Maintained -F: drivers/net/hamradio/6pack.c - 802.11 (including CFG80211/NL80211) M: Johannes Berg <[email protected]> L: [email protected]
@@ -4281,14 +4275,6 @@ S: Maintained F: Documentation/devicetree/bindings/leds/backlight/awinic,aw99706.yaml F: drivers/video/backlight/aw99706.c -AX.25 NETWORK LAYER -L: [email protected] -S: Orphan -W: https://linux-ax25.in-berlin.de -F: include/net/ax25.h -F: include/uapi/linux/ax25.h -F: net/ax25/ - AXENTIA ARM DEVICES M: Peter Rosin <[email protected]> L: [email protected] (moderated for non-subscribers)
@@ -4430,13 +4416,6 @@ F: include/uapi/linux/batadv_packet.h F: include/uapi/linux/batman_adv.h F: net/batman-adv/ -BAYCOM/HDLCDRV DRIVERS FOR AX.25 -M: Thomas Sailer <[email protected]> -L: [email protected] -S: Maintained -W: http://www.baycom.org/~tom/ham/ham.html -F: drivers/net/hamradio/baycom* - BCACHE (BLOCK LAYER CACHE) M: Coly Li <[email protected]> M: Kent Overstreet <[email protected]>
@@ -7020,20 +6999,6 @@ S: Maintained F: drivers/rtc/rtc-ds1685.c F: include/linux/rtc/ds1685.h -DAMA SLAVE for AX.25 -M: Joerg Reuter <[email protected]> -L: [email protected] -S: Maintained -W: http://yaina.de/jreuter/ -W: http://www.qsl.net/dl1bke/ -F: net/ax25/af_ax25.c -F: net/ax25/ax25_dev.c -F: net/ax25/ax25_ds_* -F: net/ax25/ax25_in.c -F: net/ax25/ax25_out.c -F: net/ax25/ax25_timer.c -F: net/ax25/sysctl_net_ax25.c - DASHARO ACPI PLATFORM DRIVER M: Michał Kopeć <[email protected]> S: Maintained
@@ -11444,11 +11409,6 @@ T: git https://github.com/Rust-for-Linux/linux.git timekeeping-next F: rust/kernel/time.rs F: rust/kernel/time/ -HIGH-SPEED SCC DRIVER FOR AX.25 -L: [email protected] -S: Orphan -F: drivers/net/hamradio/scc.c - HIGHPOINT ROCKETRAID 3xxx RAID DRIVER M: HighPoint Linux Team <[email protected]> S: Supported
@@ -18272,14 +18232,6 @@ F: net/bridge/br_netfilter*.c F: net/netfilter/ F: tools/testing/selftests/net/netfilter/ -NETROM NETWORK LAYER -L: [email protected] -S: Orphan -W: https://linux-ax25.in-berlin.de -F: include/net/netrom.h -F: include/uapi/linux/netrom.h -F: net/netrom/ - NETRONIX EMBEDDED CONTROLLER M: Jonathan Neuschäfer <[email protected]> S: Maintained
@@ -23072,14 +23024,6 @@ F: include/linux/mfd/rohm-bd96802.h F: include/linux/mfd/rohm-generic.h F: include/linux/mfd/rohm-shared.h -ROSE NETWORK LAYER -L: [email protected] -S: Orphan -W: https://linux-ax25.in-berlin.de -F: include/net/rose.h -F: include/uapi/linux/rose.h -F: net/rose/ - ROTATION DRIVER FOR ALLWINNER A83T M: Jernej Skrabec <[email protected]> L: [email protected]
@@ -29105,13 +29049,6 @@ F: lib/decompress_unxz.c F: lib/xz/ F: scripts/xz_wrap.sh -YAM DRIVER FOR AX.25 -M: Jean-Paul Roubelat <[email protected]> -L: [email protected] -S: Maintained -F: drivers/net/hamradio/yam* -F: include/linux/yam.h - YAMA SECURITY MODULE M: Kees Cook <[email protected]> S: Supported
@@ -29133,16 +29070,6 @@ S: Maintained F: Documentation/input/devices/yealink.rst F: drivers/input/misc/yealink.* -Z8530 DRIVER FOR AX.25 -M: Joerg Reuter <[email protected]> -L: [email protected] -S: Maintained -W: http://yaina.de/jreuter/ -W: http://www.qsl.net/dl1bke/ -F: Documentation/networking/device_drivers/hamradio/z8530drv.rst -F: drivers/net/hamradio/*scc.c -F: drivers/net/hamradio/z8530.h - ZD1211RW WIRELESS DRIVER L: [email protected] S: Orphan
Documentation/.renames.txt +0 -2
@@ -783,7 +783,6 @@ namespaces/compatibility-list admin-guide/namespaces/compatibility-list namespaces/index admin-guide/namespaces/index namespaces/resource-control admin-guide/namespaces/resource-control networking/altera_tse networking/device_drivers/ethernet/altera/altera_tse -networking/baycom networking/device_drivers/hamradio/baycom networking/bpf_flow_dissector bpf/prog_flow_dissector networking/cxacru networking/device_drivers/atm/cxacru networking/defza networking/device_drivers/fddi/defza
@@ -846,7 +845,6 @@ networking/ixgbe networking/device_drivers/ethernet/intel/ixgbe networking/ixgbevf networking/device_drivers/ethernet/intel/ixgbevf networking/netdev-FAQ process/maintainer-netdev networking/skfp networking/device_drivers/fddi/skfp -networking/z8530drv networking/device_drivers/hamradio/z8530drv nfc/index driver-api/nfc/index nfc/nfc-hci driver-api/nfc/nfc-hci nfc/nfc-pn544 driver-api/nfc/nfc-pn544
Documentation/admin-guide/kernel-parameters.txt +0 -18
@@ -6,7 +6,6 @@ APPARMOR AppArmor support is enabled. ARM ARM architecture is enabled. ARM64 ARM64 architecture is enabled. - AX25 Appropriate AX.25 support is enabled. CLK Common clock infrastructure is enabled. CMA Contiguous Memory Area support is enabled. DRM Direct Rendering Management support is enabled.
@@ -633,23 +632,6 @@ Kernel parameters 1 - Enable the BAU. unset - Disable the BAU. - baycom_epp= [HW,AX25] - Format: <io>,<mode> - - baycom_par= [HW,AX25] BayCom Parallel Port AX.25 Modem - Format: <io>,<mode> - See header of drivers/net/hamradio/baycom_par.c. - - baycom_ser_fdx= [HW,AX25] - BayCom Serial Port AX.25 Modem (Full Duplex Mode) - Format: <io>,<irq>,<mode>[,<baud>] - See header of drivers/net/hamradio/baycom_ser_fdx.c. - - baycom_ser_hdx= [HW,AX25] - BayCom Serial Port AX.25 Modem (Half Duplex Mode) - Format: <io>,<irq>,<mode> - See header of drivers/net/hamradio/baycom_ser_hdx.c. - bdev_allow_write_mounted= Format: <bool> Control the ability to open a mounted block device
Documentation/networking/6pack.rst deleted +0 -191
191 lines not on this page · raw message
Documentation/networking/ax25.rst deleted +0 -17
@@ -1,17 +0,0 @@ -.. SPDX-License-Identifier: GPL-2.0 - -===== -AX.25 -===== - -To use the amateur radio protocols within Linux you will need to get a -suitable copy of the AX.25 Utilities. More detailed information about -AX.25, NET/ROM and ROSE, associated programs and utilities can be -found on https://linux-ax25.in-berlin.de. - -There is a mailing list for discussing Linux amateur radio matters -called [email protected]. To subscribe to it, send a message to [email protected] or use the web interface at -https://vger.kernel.org. The subject and body of the message are -ignored. You don't need to be subscribed to post but of course that -means you might miss an answer.
Documentation/networking/device_drivers/hamradio/baycom.rst deleted +0 -174
174 lines not on this page · raw message
Documentation/networking/device_drivers/hamradio/index.rst deleted +0 -12
@@ -1,12 +0,0 @@ -.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) - -Amateur Radio Device Drivers -============================ - -Contents: - -.. toctree:: - :maxdepth: 2 - - baycom - z8530drv
Documentation/networking/device_drivers/hamradio/z8530drv.rst deleted +0 -686
686 lines not on this page · raw message
Documentation/networking/device_drivers/index.rst +0 -1
@@ -13,6 +13,5 @@ Hardware Device Drivers cellular/index ethernet/index fddi/index - hamradio/index wifi/index wwan/index
Documentation/networking/index.rst +0 -2
@@ -40,11 +40,9 @@ Refer to :ref:`netdev-FAQ` for a guide on netdev development process specifics. tls-handshake nfc 6lowpan - 6pack arcnet-hardware arcnet atm - ax25 bonding cdc_mbim dctcp
Documentation/staging/magic-number.rst +0 -3
@@ -72,11 +72,8 @@ PG_MAGIC 'P' pg_{read,write}_hdr ``include/uapi/l APM_BIOS_MAGIC 0x4101 apm_user ``arch/x86/kernel/apm_32.c`` FASYNC_MAGIC 0x4601 fasync_struct ``include/linux/fs.h`` SLIP_MAGIC 0x5302 slip ``drivers/net/slip/slip.h`` -BAYCOM_MAGIC 19730510 baycom_state ``drivers/net/hamradio/baycom_epp.c`` -HDLCDRV_MAGIC 0x5ac6e778 hdlcdrv_state ``include/linux/hdlcdrv.h`` KV_MAGIC 0x5f4b565f kernel_vars_s ``arch/mips/include/asm/sn/klkernvars.h`` CODA_MAGIC 0xC0DAC0DA coda_file_info ``fs/coda/coda_fs_i.h`` -YAM_MAGIC 0xF10A7654 yam_port ``drivers/net/hamradio/yam.c`` CCB_MAGIC 0xf2691ad2 ccb ``drivers/scsi/ncr53c8xx.c`` QUEUE_MAGIC_FREE 0xf7e1c9a3 queue_entry ``drivers/scsi/arm/queue.c`` QUEUE_MAGIC_USED 0xf7e1cc33 queue_entry ``drivers/scsi/arm/queue.c``
Documentation/translations/it_IT/staging/magic-number.rst +0 -3
@@ -78,11 +78,8 @@ PG_MAGIC 'P' pg_{read,write}_hdr ``include/linux/ APM_BIOS_MAGIC 0x4101 apm_user ``arch/x86/kernel/apm_32.c`` FASYNC_MAGIC 0x4601 fasync_struct ``include/linux/fs.h`` SLIP_MAGIC 0x5302 slip ``drivers/net/slip.h`` -BAYCOM_MAGIC 0x19730510 baycom_state ``drivers/net/baycom_epp.c`` -HDLCDRV_MAGIC 0x5ac6e778 hdlcdrv_state ``include/linux/hdlcdrv.h`` KV_MAGIC 0x5f4b565f kernel_vars_s ``arch/mips/include/asm/sn/klkernvars.h`` CODA_MAGIC 0xC0DAC0DA coda_file_info ``fs/coda/coda_fs_i.h`` -YAM_MAGIC 0xF10A7654 yam_port ``drivers/net/hamradio/yam.c`` CCB_MAGIC 0xf2691ad2 ccb ``drivers/scsi/ncr53c8xx.c`` QUEUE_MAGIC_FREE 0xf7e1c9a3 queue_entry ``drivers/scsi/arm/queue.c`` QUEUE_MAGIC_USED 0xf7e1cc33 queue_entry ``drivers/scsi/arm/queue.c``
Documentation/translations/sp_SP/process/magic-number.rst +0 -3
@@ -77,11 +77,8 @@ PG_MAGIC 'P' pg_{read,write}_hdr ``include/linux/ APM_BIOS_MAGIC 0x4101 apm_user ``arch/x86/kernel/apm_32.c`` FASYNC_MAGIC 0x4601 fasync_struct ``include/linux/fs.h`` SLIP_MAGIC 0x5302 slip ``drivers/net/slip.h`` -BAYCOM_MAGIC 0x19730510 baycom_state ``drivers/net/baycom_epp.c`` -HDLCDRV_MAGIC 0x5ac6e778 hdlcdrv_state ``include/linux/hdlcdrv.h`` KV_MAGIC 0x5f4b565f kernel_vars_s ``arch/mips/include/asm/sn/klkernvars.h`` CODA_MAGIC 0xC0DAC0DA coda_file_info ``fs/coda/coda_fs_i.h`` -YAM_MAGIC 0xF10A7654 yam_port ``drivers/net/hamradio/yam.c`` CCB_MAGIC 0xf2691ad2 ccb ``drivers/scsi/ncr53c8xx.c`` QUEUE_MAGIC_FREE 0xf7e1c9a3 queue_entry ``drivers/scsi/arm/queue.c`` QUEUE_MAGIC_USED 0xf7e1cc33 queue_entry ``drivers/scsi/arm/queue.c``
Documentation/translations/zh_CN/process/magic-number.rst +0 -3
@@ -70,11 +70,8 @@ PG_MAGIC 'P' pg_{read,write}_hdr ``include/linux/ APM_BIOS_MAGIC 0x4101 apm_user ``arch/x86/kernel/apm_32.c`` FASYNC_MAGIC 0x4601 fasync_struct ``include/linux/fs.h`` SLIP_MAGIC 0x5302 slip ``drivers/net/slip.h`` -BAYCOM_MAGIC 0x19730510 baycom_state ``drivers/net/baycom_epp.c`` -HDLCDRV_MAGIC 0x5ac6e778 hdlcdrv_state ``include/linux/hdlcdrv.h`` KV_MAGIC 0x5f4b565f kernel_vars_s ``arch/mips/include/asm/sn/klkernvars.h`` CODA_MAGIC 0xC0DAC0DA coda_file_info ``fs/coda/coda_fs_i.h`` -YAM_MAGIC 0xF10A7654 yam_port ``drivers/net/hamradio/yam.c`` CCB_MAGIC 0xf2691ad2 ccb ``drivers/scsi/ncr53c8xx.c`` QUEUE_MAGIC_FREE 0xf7e1c9a3 queue_entry ``drivers/scsi/arm/queue.c`` QUEUE_MAGIC_USED 0xf7e1cc33 queue_entry ``drivers/scsi/arm/queue.c``
Documentation/translations/zh_TW/process/magic-number.rst +0 -3
@@ -64,11 +64,8 @@ PG_MAGIC 'P' pg_{read,write}_hdr ``include/linux/ APM_BIOS_MAGIC 0x4101 apm_user ``arch/x86/kernel/apm_32.c`` FASYNC_MAGIC 0x4601 fasync_struct ``include/linux/fs.h`` SLIP_MAGIC 0x5302 slip ``drivers/net/slip.h`` -BAYCOM_MAGIC 0x19730510 baycom_state ``drivers/net/baycom_epp.c`` -HDLCDRV_MAGIC 0x5ac6e778 hdlcdrv_state ``include/linux/hdlcdrv.h`` KV_MAGIC 0x5f4b565f kernel_vars_s ``arch/mips/include/asm/sn/klkernvars.h`` CODA_MAGIC 0xC0DAC0DA coda_file_info ``fs/coda/coda_fs_i.h`` -YAM_MAGIC 0xF10A7654 yam_port ``drivers/net/hamradio/yam.c`` CCB_MAGIC 0xf2691ad2 ccb ``drivers/scsi/ncr53c8xx.c`` QUEUE_MAGIC_FREE 0xf7e1c9a3 queue_entry ``drivers/scsi/arm/queue.c`` QUEUE_MAGIC_USED 0xf7e1cc33 queue_entry ``drivers/scsi/arm/queue.c``
drivers/net/hamradio/Kconfig deleted +0 -162
162 lines not on this page · raw message
net/Kconfig +0 -1
@@ -414,7 +414,6 @@ endmenu # Network testing endmenu # Networking options -source "net/ax25/Kconfig" source "net/can/Kconfig" source "net/bluetooth/Kconfig" source "net/rxrpc/Kconfig"
net/ax25/Kconfig deleted +0 -108
108 lines not on this page · raw message
drivers/net/Makefile +0 -1
@@ -54,7 +54,6 @@ obj-y += dsa/ endif obj-$(CONFIG_ETHERNET) += ethernet/ obj-$(CONFIG_FDDI) += fddi/ -obj-$(CONFIG_HAMRADIO) += hamradio/ obj-$(CONFIG_QCOM_IPA) += ipa/ obj-$(CONFIG_PLIP) += plip/ obj-$(CONFIG_PPP) += ppp/
drivers/net/hamradio/Makefile deleted +0 -22
@@ -1,22 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -# -# Makefile for the Linux AX.25 and HFMODEM device drivers. -# -# -# 19971130 Moved the amateur radio related network drivers from -# drivers/net/ to drivers/hamradio for easier maintenance. -# Joerg Reuter DL1BKE <[email protected]> -# -# 20000806 Rewritten to use lists instead of if-statements. -# Christoph Hellwig <[email protected]> -# - -obj-$(CONFIG_SCC) += scc.o -obj-$(CONFIG_MKISS) += mkiss.o -obj-$(CONFIG_6PACK) += 6pack.o -obj-$(CONFIG_YAM) += yam.o -obj-$(CONFIG_BPQETHER) += bpqether.o -obj-$(CONFIG_BAYCOM_SER_FDX) += baycom_ser_fdx.o hdlcdrv.o -obj-$(CONFIG_BAYCOM_SER_HDX) += baycom_ser_hdx.o hdlcdrv.o -obj-$(CONFIG_BAYCOM_PAR) += baycom_par.o hdlcdrv.o -obj-$(CONFIG_BAYCOM_EPP) += baycom_epp.o hdlcdrv.o
net/Makefile +0 -3
@@ -28,9 +28,6 @@ obj-y += dsa/ obj-$(CONFIG_ATALK) += appletalk/ obj-$(CONFIG_X25) += x25/ obj-$(CONFIG_LAPB) += lapb/ -obj-$(CONFIG_NETROM) += netrom/ -obj-$(CONFIG_ROSE) += rose/ -obj-$(CONFIG_AX25) += ax25/ obj-$(CONFIG_CAN) += can/ obj-$(CONFIG_BT) += bluetooth/ obj-$(CONFIG_SUNRPC) += sunrpc/
net/ax25/Makefile deleted +0 -12
@@ -1,12 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -# -# Makefile for the Linux AX.25 layer. -# - -obj-$(CONFIG_AX25) += ax25.o - -ax25-y := ax25_addr.o ax25_dev.o ax25_iface.o ax25_in.o ax25_ip.o ax25_out.o \ - ax25_route.o ax25_std_in.o ax25_std_subr.o ax25_std_timer.o \ - ax25_subr.o ax25_timer.o ax25_uid.o af_ax25.o -ax25-$(CONFIG_AX25_DAMA_SLAVE) += ax25_ds_in.o ax25_ds_subr.o ax25_ds_timer.o -ax25-$(CONFIG_SYSCTL) += sysctl_net_ax25.o
net/netrom/Makefile deleted +0 -10
@@ -1,10 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -# -# Makefile for the Linux NET/ROM layer. -# - -obj-$(CONFIG_NETROM) += netrom.o - -netrom-y := af_netrom.o nr_dev.o nr_in.o nr_loopback.o \ - nr_out.o nr_route.o nr_subr.o nr_timer.o -netrom-$(CONFIG_SYSCTL) += sysctl_net_netrom.o
net/rose/Makefile deleted +0 -10
@@ -1,10 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -# -# Makefile for the Linux Rose (X.25 PLP) layer. -# - -obj-$(CONFIG_ROSE) += rose.o - -rose-y := af_rose.o rose_dev.o rose_in.o rose_link.o rose_loopback.o \ - rose_out.o rose_route.o rose_subr.o rose_timer.o -rose-$(CONFIG_SYSCTL) += sysctl_net_rose.o
drivers/net/hamradio/z8530.h deleted +0 -246
246 lines not on this page · raw message
include/linux/hdlcdrv.h deleted +0 -276
276 lines not on this page · raw message
include/linux/netdevice.h +1 -4
@@ -162,7 +162,7 @@ static inline bool dev_xmit_complete(int rc)#if defined(CONFIG_HYPERV_NET )# define LL_MAX_HEADER 128 -#elif defined(CONFIG_WLAN ) ||IS_ENABLED (CONFIG_AX25 ) +#elif defined(CONFIG_WLAN )# if defined(CONFIG_MAC80211_MESH )# define LL_MAX_HEADER 128# else
@@ -2316,9 +2316,6 @@ struct net_device {#if IS_ENABLED (CONFIG_ATALK )void *atalk_ptr;#endif -#if IS_ENABLED (CONFIG_AX25 ) -struct ax25_dev __rcu *ax25_ptr; -#endif #if IS_ENABLED (CONFIG_CFG80211 )struct wireless_dev *ieee80211_ptr;#endif
include/linux/scc.h deleted +0 -86
86 lines not on this page · raw message
include/linux/yam.h deleted +0 -67
67 lines not on this page · raw message
include/net/ax25.h +3 -473
483 lines not on this page · raw message
include/net/netrom.h deleted +0 -273
155 lines not on this page · raw message
include/net/rose.h +2 -261
263 lines not on this page · raw message
include/uapi/linux/hdlcdrv.h deleted +0 -111
111 lines not on this page · raw message
include/uapi/linux/rose.h deleted +0 -91
91 lines not on this page · raw message
include/uapi/linux/scc.h deleted +0 -174
174 lines not on this page · raw message
drivers/net/hamradio/6pack.c deleted +0 -912
912 lines not on this page · raw message
drivers/net/hamradio/baycom_epp.c deleted +0 -1316
1,316 lines not on this page · raw message
drivers/net/hamradio/baycom_par.c deleted +0 -598
598 lines not on this page · raw message
drivers/net/hamradio/baycom_ser_fdx.c deleted +0 -678
678 lines not on this page · raw message
drivers/net/hamradio/baycom_ser_hdx.c deleted +0 -727
727 lines not on this page · raw message
drivers/net/hamradio/bpqether.c deleted +0 -593
593 lines not on this page · raw message
drivers/net/hamradio/hdlcdrv.c deleted +0 -747
747 lines not on this page · raw message
drivers/net/hamradio/mkiss.c deleted +0 -980
980 lines not on this page · raw message
drivers/net/hamradio/scc.c deleted +0 -2179
2,179 lines not on this page · raw message
drivers/net/hamradio/yam.c deleted +0 -1191
1,191 lines not on this page · raw message
net/ax25/af_ax25.c deleted +0 -2089
2,089 lines not on this page · raw message
net/ax25/ax25_addr.c deleted +0 -303
303 lines not on this page · raw message
net/ax25/ax25_dev.c deleted +0 -200
200 lines not on this page · raw message
net/ax25/ax25_ds_in.c deleted +0 -298
298 lines not on this page · raw message
net/ax25/ax25_ds_subr.c deleted +0 -204
204 lines not on this page · raw message
net/ax25/ax25_ds_timer.c deleted +0 -235
235 lines not on this page · raw message
net/ax25/ax25_iface.c deleted +0 -214
214 lines not on this page · raw message
net/ax25/ax25_in.c deleted +0 -455
455 lines not on this page · raw message
net/ax25/ax25_ip.c deleted +0 -247
247 lines not on this page · raw message
net/ax25/ax25_out.c deleted +0 -398
398 lines not on this page · raw message
net/ax25/ax25_route.c deleted +0 -416
416 lines not on this page · raw message
net/ax25/ax25_std_in.c deleted +0 -443
443 lines not on this page · raw message
net/ax25/ax25_std_subr.c deleted +0 -83
83 lines not on this page · raw message
net/ax25/ax25_std_timer.c deleted +0 -175
175 lines not on this page · raw message
net/ax25/ax25_subr.c deleted +0 -296
296 lines not on this page · raw message
net/ax25/ax25_timer.c deleted +0 -224
224 lines not on this page · raw message
net/ax25/ax25_uid.c deleted +0 -204
204 lines not on this page · raw message
net/ax25/sysctl_net_ax25.c deleted +0 -181
181 lines not on this page · raw message
net/netrom/af_netrom.c deleted +0 -1536
1,536 lines not on this page · raw message
net/netrom/nr_dev.c deleted +0 -178
178 lines not on this page · raw message
net/netrom/nr_in.c deleted +0 -301
301 lines not on this page · raw message
net/netrom/nr_loopback.c deleted +0 -73
73 lines not on this page · raw message
net/netrom/nr_out.c deleted +0 -272
272 lines not on this page · raw message
net/netrom/nr_route.c deleted +0 -989
989 lines not on this page · raw message
net/netrom/nr_subr.c deleted +0 -280
280 lines not on this page · raw message
net/netrom/nr_timer.c deleted +0 -249
249 lines not on this page · raw message
net/netrom/sysctl_net_netrom.c deleted +0 -156
156 lines not on this page · raw message
net/rose/af_rose.c deleted +0 -1687
1,687 lines not on this page · raw message
net/rose/rose_dev.c deleted +0 -141
141 lines not on this page · raw message
net/rose/rose_in.c deleted +0 -301
301 lines not on this page · raw message
net/rose/rose_link.c deleted +0 -289
289 lines not on this page · raw message
net/rose/rose_loopback.c deleted +0 -133
133 lines not on this page · raw message
net/rose/rose_out.c deleted +0 -122
122 lines not on this page · raw message
net/rose/rose_route.c deleted +0 -1333
1,333 lines not on this page · raw message
net/rose/rose_subr.c deleted +0 -556
556 lines not on this page · raw message
net/rose/rose_timer.c deleted +0 -227
227 lines not on this page · raw message
net/rose/sysctl_net_rose.c deleted +0 -125
125 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
2.53.0
Part of the diff is not shown here. View the raw message.
Quoted 11 lines · Jakub Kicinski
Remove the amateur radio (AX.25, NET/ROM, ROSE) protocol implementation and all associated hamradio device drivers from the kernel tree. This set of protocols has long been a huge bug/syzbot magnet, and since nobody stepped up to help us deal with the influx of the AI-generated bug reports we need to move it out of tree to protect our sanity.
The code is moved to an out-of-tree repo:
https://github.com/linux-netdev/mod-orphan
if it's cleaned up and reworked there we can accept it back.
Quoted 6 lines
Minimal stub headers are kept for
include/net/ax25.h(AX25_P_IP,AX25_ADDR_LEN,ax25_address) andinclude/net/rose.h(ROSE_ADDR_LEN) so that the conditional integration code inarp.candtun.ccontinues to compile and work when the out-of-tree modules are loaded.Signed-off-by Jakub Kicinski <[email protected]>
Quoted 11 lines · On Mon, 20 Apr 2026 19:18:23 -0700 Jakub Kicinski <[email protected]> wrote:
Remove the amateur radio (AX.25, NET/ROM, ROSE) protocol implementation and all associated hamradio device drivers from the kernel tree. This set of protocols has long been a huge bug/syzbot magnet, and since nobody stepped up to help us deal with the influx of the AI-generated bug reports we need to move it out of tree to protect our sanity.
The code is moved to an out-of-tree repo:
https://github.com/linux-netdev/mod-orphan
if it's cleaned up and reworked there we can accept it back.
Quoted 7 lines
Minimal stub headers are kept for
include/net/ax25.h(AX25_P_IP,AX25_ADDR_LEN,ax25_address) andinclude/net/rose.h(ROSE_ADDR_LEN) so that the conditional integration code inarp.candtun.ccontinues to compile and work when the out-of-tree modules are loaded.Signed-off-by Jakub Kicinski <[email protected]>---
PS: once this is merged will remove these protos from iproute2 as well
Quoted 10 lines · On Mon, 20 Apr 2026 19:18:23 -0700 Jakub Kicinski <[email protected]> wrote:
Remove the amateur radio (AX.25, NET/ROM, ROSE) protocol implementation and all associated hamradio device drivers from the kernel tree. This set of protocols has long been a huge bug/syzbot magnet, and since nobody stepped up to help us deal with the influx of the AI-generated bug reports we need to move it out of tree to protect our sanity.
The code is moved to an out-of-tree repo:
https://github.com/linux-netdev/mod-orphan
if it's cleaned up and reworked there we can accept it back.
It would be good if these protocols could be done in userspace or with BPF?
Quoted 9 lines · Stephen Hemminger
Quoted 7 lines · On Mon, 20 Apr 2026 19:18:23 -0700 Jakub Kicinski <[email protected]> wrote:
Remove the amateur radio (AX.25, NET/ROM, ROSE) protocol implementation and all associated hamradio device drivers from the kernel tree. This set of protocols has long been a huge bug/syzbot magnet, and since nobody stepped up to help us deal with the influx of the AI-generated bug reports we need to move it out of tree to protect our sanity.
Quoted 6 lines
Quoted 3 lines
The code is moved to an out-of-tree repo:
https://github.com/linux-netdev/mod-orphan
if it's cleaned up and reworked there we can accept it back.It would be good if these protocols could be done in userspace or with BPF?
Consensus for a userspace implementation is what folks on linux-hams seem to be converging on.
The amateur radio protocols are more or less specific to low-speed links, they are not particularly coupled to anything else that requires running in the kernel, and the main coupling point (IP over AX.25) can be implemented via TAP/TUN.
There are several popular packages that already implement AX.25 and NET/ROM in user-space (for the interested, LinBPQ seems to be the canonical example). The main missing piece is ROSE, but it is likely easier to add that to an existing package, or potentially something brand new, than keep it in the kernel.
There's no compelling reason to keep these protocols in the kernel, whether in-tree or out-of-tree; at least, one has not been articulated.
- Dan C.
Quoted 32 lines · On Tue, 21 Apr 2026 12:17:23 -0400 Dan Cross <[email protected]> wrote:
Quoted 9 lines · Stephen Hemminger
Quoted 7 lines · On Mon, 20 Apr 2026 19:18:23 -0700 Jakub Kicinski <[email protected]> wrote:
Remove the amateur radio (AX.25, NET/ROM, ROSE) protocol implementation and all associated hamradio device drivers from the kernel tree. This set of protocols has long been a huge bug/syzbot magnet, and since nobody stepped up to help us deal with the influx of the AI-generated bug reports we need to move it out of tree to protect our sanity.
Quoted 6 lines
Quoted 3 lines
The code is moved to an out-of-tree repo:
https://github.com/linux-netdev/mod-orphan
if it's cleaned up and reworked there we can accept it back.It would be good if these protocols could be done in userspace or with BPF?
Consensus for a userspace implementation is what folks on linux-hams seem to be converging on.
The amateur radio protocols are more or less specific to low-speed links, they are not particularly coupled to anything else that requires running in the kernel, and the main coupling point (IP over AX.25) can be implemented via TAP/TUN.
There are several popular packages that already implement AX.25 and NET/ROM in user-space (for the interested, LinBPQ seems to be the canonical example). The main missing piece is ROSE, but it is likely easier to add that to an existing package, or potentially something brand new, than keep it in the kernel.
Quoted 5 lines
There's no compelling reason to keep these protocols in the kernel, whether in-tree or out-of-tree; at least, one has not been articulated.
- Dan C.
Thanks, my other concern is carrying support for these in ip commands. If not kernel based, then iproute2 doesn't need to worry.
Quoted 35 lines · Stephen Hemminger
Quoted 32 lines · On Tue, 21 Apr 2026 12:17:23 -0400 Dan Cross <[email protected]> wrote:
Quoted 9 lines · Stephen Hemminger
Quoted 7 lines · On Mon, 20 Apr 2026 19:18:23 -0700 Jakub Kicinski <[email protected]> wrote:
Remove the amateur radio (AX.25, NET/ROM, ROSE) protocol implementation and all associated hamradio device drivers from the kernel tree. This set of protocols has long been a huge bug/syzbot magnet, and since nobody stepped up to help us deal with the influx of the AI-generated bug reports we need to move it out of tree to protect our sanity.
Quoted 6 lines
Quoted 3 lines
The code is moved to an out-of-tree repo:
https://github.com/linux-netdev/mod-orphan
if it's cleaned up and reworked there we can accept it back.It would be good if these protocols could be done in userspace or with BPF?
Consensus for a userspace implementation is what folks on linux-hams seem to be converging on.
The amateur radio protocols are more or less specific to low-speed links, they are not particularly coupled to anything else that requires running in the kernel, and the main coupling point (IP over AX.25) can be implemented via TAP/TUN.
There are several popular packages that already implement AX.25 and NET/ROM in user-space (for the interested, LinBPQ seems to be the canonical example). The main missing piece is ROSE, but it is likely easier to add that to an existing package, or potentially something brand new, than keep it in the kernel.
Quoted 6 lines
Quoted 3 lines
There's no compelling reason to keep these protocols in the kernel, whether in-tree or out-of-tree; at least, one has not been articulated.
Thanks, my other concern is carrying support for these in ip commands. If not kernel based, then iproute2 doesn't need to worry.
Agreed.
If someone really wants mimic the existing output of those commands in the context of a userspace implementation, they could write a wrapper program that invokes the real thing, and extracts relevant information from the ham protocol implementation, and interpolates it into the output. It may be an imperfect simulation, but it's probably close enough for most users.
- Dan C.
Quoted 11 lines · Jakub Kicinski
Remove the amateur radio (AX.25, NET/ROM, ROSE) protocol implementation and all associated hamradio device drivers from the kernel tree. This set of protocols has long been a huge bug/syzbot magnet, and since nobody stepped up to help us deal with the influx of the AI-generated bug reports we need to move it out of tree to protect our sanity.
The code is moved to an out-of-tree repo:
https://github.com/linux-netdev/mod-orphan
if it's cleaned up and reworked there we can accept it back.
Quoted 6 lines
Minimal stub headers are kept for
include/net/ax25.h(AX25_P_IP,AX25_ADDR_LEN,ax25_address) andinclude/net/rose.h(ROSE_ADDR_LEN) so that the conditional integration code inarp.candtun.ccontinues to compile and work when the out-of-tree modules are loaded.Signed-off-by Jakub Kicinski <[email protected]>
Quoted 30,220 lines
---
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]--- MAINTAINERS | 73 - Documentation/.renames.txt | 2 - .../admin-guide/kernel-parameters.txt | 18 - Documentation/networking/6pack.rst | 191 -- Documentation/networking/ax25.rst | 17 - .../device_drivers/hamradio/baycom.rst | 174 -- .../device_drivers/hamradio/index.rst | 12 - .../device_drivers/hamradio/z8530drv.rst | 686 ------ .../networking/device_drivers/index.rst | 1 - Documentation/networking/index.rst | 2 - Documentation/staging/magic-number.rst | 3 - .../it_IT/staging/magic-number.rst | 3 - .../sp_SP/process/magic-number.rst | 3 - .../zh_CN/process/magic-number.rst | 3 - .../zh_TW/process/magic-number.rst | 3 - drivers/net/hamradio/Kconfig | 162 -- net/Kconfig | 1 - net/ax25/Kconfig | 108 - drivers/net/Makefile | 1 - drivers/net/hamradio/Makefile | 22 - net/Makefile | 3 - net/ax25/Makefile | 12 - net/netrom/Makefile | 10 - net/rose/Makefile | 10 - drivers/net/hamradio/z8530.h | 246 -- include/linux/hdlcdrv.h | 276 --- include/linux/netdevice.h | 5 +- include/linux/scc.h | 86 - include/linux/yam.h | 67 - include/net/ax25.h | 476 +--- include/net/netrom.h | 273 --- include/net/rose.h | 263 +- include/uapi/linux/baycom.h | 40 - include/uapi/linux/hdlcdrv.h | 111 - include/uapi/linux/netrom.h | 37 - include/uapi/linux/rose.h | 91 - include/uapi/linux/scc.h | 174 -- drivers/net/hamradio/6pack.c | 912 ------- drivers/net/hamradio/baycom_epp.c | 1316 ---------- drivers/net/hamradio/baycom_par.c | 598 ----- drivers/net/hamradio/baycom_ser_fdx.c | 678 ----- drivers/net/hamradio/baycom_ser_hdx.c | 727 ------ drivers/net/hamradio/bpqether.c | 593 ----- drivers/net/hamradio/hdlcdrv.c | 747 ------ drivers/net/hamradio/mkiss.c | 980 -------- drivers/net/hamradio/scc.c | 2179 ----------------- drivers/net/hamradio/yam.c | 1191 --------- net/ax25/af_ax25.c | 2089 ---------------- net/ax25/ax25_addr.c | 303 --- net/ax25/ax25_dev.c | 200 -- net/ax25/ax25_ds_in.c | 298 --- net/ax25/ax25_ds_subr.c | 204 -- net/ax25/ax25_ds_timer.c | 235 -- net/ax25/ax25_iface.c | 214 -- net/ax25/ax25_in.c | 455 ---- net/ax25/ax25_ip.c | 247 -- net/ax25/ax25_out.c | 398 --- net/ax25/ax25_route.c | 416 ---- net/ax25/ax25_std_in.c | 443 ---- net/ax25/ax25_std_subr.c | 83 - net/ax25/ax25_std_timer.c | 175 -- net/ax25/ax25_subr.c | 296 --- net/ax25/ax25_timer.c | 224 -- net/ax25/ax25_uid.c | 204 -- net/ax25/sysctl_net_ax25.c | 181 -- net/ipv4/arp.c | 1 - net/netrom/af_netrom.c | 1536 ------------ net/netrom/nr_dev.c | 178 -- net/netrom/nr_in.c | 301 --- net/netrom/nr_loopback.c | 73 - net/netrom/nr_out.c | 272 -- net/netrom/nr_route.c | 989 -------- net/netrom/nr_subr.c | 280 --- net/netrom/nr_timer.c | 249 -- net/netrom/sysctl_net_netrom.c | 156 -- net/rose/af_rose.c | 1687 ------------- net/rose/rose_dev.c | 141 -- net/rose/rose_in.c | 301 --- net/rose/rose_link.c | 289 --- net/rose/rose_loopback.c | 133 - net/rose/rose_out.c | 122 - net/rose/rose_route.c | 1333 ---------- net/rose/rose_subr.c | 556 ----- net/rose/rose_timer.c | 227 -- net/rose/sysctl_net_rose.c | 125 - arch/mips/configs/bcm47xx_defconfig | 1 - arch/mips/configs/bigsur_defconfig | 10 - arch/mips/configs/gpr_defconfig | 11 - arch/mips/configs/mtx1_defconfig | 11 - arch/mips/configs/rb532_defconfig | 1 - arch/mips/configs/rm200_defconfig | 7 - arch/mips/configs/rt305x_defconfig | 1 - arch/mips/configs/xway_defconfig | 1 - 93 files changed, 6 insertions(+), 29237 deletions(-)delete mode 100644
Documentation/networking/6pack.rst
delete mode 100644Documentation/networking/ax25.rst
delete mode 100644Documentation/networking/device_drivers/hamradio/baycom.rstdelete mode 100644Documentation/networking/device_drivers/hamradio/index.rstdelete mode 100644Documentation/networking/device_drivers/hamradio/z8530drv.rstdelete mode 100644drivers/net/hamradio/Kconfig
delete mode 100644net/ax25/Kconfig
delete mode 100644drivers/net/hamradio/Makefile
delete mode 100644net/ax25/Makefile
delete mode 100644net/netrom/Makefile
delete mode 100644net/rose/Makefile
delete mode 100644drivers/net/hamradio/z8530.h
delete mode 100644include/linux/hdlcdrv.h
delete mode 100644include/linux/scc.h
delete mode 100644include/linux/yam.h
delete mode 100644include/net/netrom.h
delete mode 100644include/uapi/linux/baycom.h
delete mode 100644include/uapi/linux/hdlcdrv.h
delete mode 100644include/uapi/linux/netrom.h
delete mode 100644include/uapi/linux/rose.h
delete mode 100644include/uapi/linux/scc.h
delete mode 100644drivers/net/hamradio/6pack.c
delete mode 100644drivers/net/hamradio/baycom_epp.c
delete mode 100644drivers/net/hamradio/baycom_par.c
delete mode 100644drivers/net/hamradio/baycom_ser_fdx.c
delete mode 100644drivers/net/hamradio/baycom_ser_hdx.c
delete mode 100644drivers/net/hamradio/bpqether.c
delete mode 100644drivers/net/hamradio/hdlcdrv.c
delete mode 100644drivers/net/hamradio/mkiss.c
delete mode 100644drivers/net/hamradio/scc.c
delete mode 100644drivers/net/hamradio/yam.c
delete mode 100644net/ax25/af_ax25.c
delete mode 100644net/ax25/ax25_addr.c
delete mode 100644net/ax25/ax25_dev.c
delete mode 100644net/ax25/ax25_ds_in.c
delete mode 100644net/ax25/ax25_ds_subr.c
delete mode 100644net/ax25/ax25_ds_timer.c
delete mode 100644net/ax25/ax25_iface.c
delete mode 100644net/ax25/ax25_in.c
delete mode 100644net/ax25/ax25_ip.c
delete mode 100644net/ax25/ax25_out.c
delete mode 100644net/ax25/ax25_route.c
delete mode 100644net/ax25/ax25_std_in.c
delete mode 100644net/ax25/ax25_std_subr.c
delete mode 100644net/ax25/ax25_std_timer.c
delete mode 100644net/ax25/ax25_subr.c
delete mode 100644net/ax25/ax25_timer.c
delete mode 100644net/ax25/ax25_uid.c
delete mode 100644net/ax25/sysctl_net_ax25.c
delete mode 100644net/netrom/af_netrom.c
delete mode 100644net/netrom/nr_dev.c
delete mode 100644net/netrom/nr_in.c
delete mode 100644net/netrom/nr_loopback.c
delete mode 100644net/netrom/nr_out.c
delete mode 100644net/netrom/nr_route.c
delete mode 100644net/netrom/nr_subr.c
delete mode 100644net/netrom/nr_timer.c
delete mode 100644net/netrom/sysctl_net_netrom.c
delete mode 100644net/rose/af_rose.c
delete mode 100644net/rose/rose_dev.c
delete mode 100644net/rose/rose_in.c
delete mode 100644net/rose/rose_link.c
delete mode 100644net/rose/rose_loopback.c
delete mode 100644net/rose/rose_out.c
delete mode 100644net/rose/rose_route.c
delete mode 100644net/rose/rose_subr.c
delete mode 100644net/rose/rose_timer.c
delete mode 100644net/rose/sysctl_net_rose.cMAINTAINERS +0
-73@@ -102,12 +102,6 @@ F: Documentation/networking/6lowpan.rst F: include/net/6lowpan.h F: net/6lowpan/ -6PACK NETWORK DRIVER FOR AX.25 -M: Andreas Koensgen <[email protected]> -L: [email protected] -S: Maintained -F: drivers/net/hamradio/6pack.c - 802.11 (including CFG80211/NL80211) M: Johannes Berg <[email protected]> L: [email protected]@@ -4281,14 +4275,6 @@ S: Maintained F: Documentation/devicetree/bindings/leds/backlight/awinic,aw99706.yaml F: drivers/video/backlight/aw99706.c -AX.25 NETWORK LAYER -L: [email protected] -S: Orphan -W: https://linux-ax25.in-berlin.de -F: include/net/ax25.h -F: include/uapi/linux/ax25.h -F: net/ax25/ - AXENTIA ARM DEVICES M: Peter Rosin <[email protected]> L: [email protected] (moderated for non-subscribers)@@ -4430,13 +4416,6 @@ F: include/uapi/linux/batadv_packet.h F: include/uapi/linux/batman_adv.h F: net/batman-adv/ -BAYCOM/HDLCDRV DRIVERS FOR AX.25 -M: Thomas Sailer <[email protected]> -L: [email protected] -S: Maintained -W: http://www.baycom.org/~tom/ham/ham.html -F: drivers/net/hamradio/baycom* - BCACHE (BLOCK LAYER CACHE) M: Coly Li <[email protected]> M: Kent Overstreet <[email protected]>@@ -7020,20 +6999,6 @@ S: Maintained F: drivers/rtc/rtc-ds1685.c F: include/linux/rtc/ds1685.h -DAMA SLAVE for AX.25 -M: Joerg Reuter <[email protected]> -L: [email protected] -S: Maintained -W: http://yaina.de/jreuter/ -W: http://www.qsl.net/dl1bke/ -F: net/ax25/af_ax25.c -F: net/ax25/ax25_dev.c -F: net/ax25/ax25_ds_* -F: net/ax25/ax25_in.c -F: net/ax25/ax25_out.c -F: net/ax25/ax25_timer.c -F: net/ax25/sysctl_net_ax25.c - DASHARO ACPI PLATFORM DRIVER M: Michał Kopeć <[email protected]> S: Maintained@@ -11444,11 +11409,6 @@ T: git https://github.com/Rust-for-Linux/linux.git timekeeping-next F: rust/kernel/time.rs F: rust/kernel/time/ -HIGH-SPEED SCC DRIVER FOR AX.25 -L: [email protected] -S: Orphan -F: drivers/net/hamradio/scc.c - HIGHPOINT ROCKETRAID 3xxx RAID DRIVER M: HighPoint Linux Team <[email protected]> S: Supported@@ -18272,14 +18232,6 @@ F: net/bridge/br_netfilter*.c F: net/netfilter/ F: tools/testing/selftests/net/netfilter/ -NETROM NETWORK LAYER -L: [email protected] -S: Orphan -W: https://linux-ax25.in-berlin.de -F: include/net/netrom.h -F: include/uapi/linux/netrom.h -F: net/netrom/ - NETRONIX EMBEDDED CONTROLLER M: Jonathan Neuschäfer <[email protected]> S: Maintained@@ -23072,14 +23024,6 @@ F: include/linux/mfd/rohm-bd96802.h F: include/linux/mfd/rohm-generic.h F: include/linux/mfd/rohm-shared.h -ROSE NETWORK LAYER -L: [email protected] -S: Orphan -W: https://linux-ax25.in-berlin.de -F: include/net/rose.h -F: include/uapi/linux/rose.h -F: net/rose/ - ROTATION DRIVER FOR ALLWINNER A83T M: Jernej Skrabec <[email protected]> L: [email protected]@@ -29105,13 +29049,6 @@ F: lib/decompress_unxz.c F: lib/xz/ F: scripts/xz_wrap.sh -YAM DRIVER FOR AX.25 -M: Jean-Paul Roubelat <[email protected]> -L: [email protected] -S: Maintained -F: drivers/net/hamradio/yam* -F: include/linux/yam.h - YAMA SECURITY MODULE M: Kees Cook <[email protected]> S: Supported@@ -29133,16 +29070,6 @@ S: Maintained F: Documentation/input/devices/yealink.rst F: drivers/input/misc/yealink.* -Z8530 DRIVER FOR AX.25 -M: Joerg Reuter <[email protected]> -L: [email protected] -S: Maintained -W: http://yaina.de/jreuter/ -W: http://www.qsl.net/dl1bke/ -F: Documentation/networking/device_drivers/hamradio/z8530drv.rst -F: drivers/net/hamradio/*scc.c -F: drivers/net/hamradio/z8530.h - ZD1211RW WIRELESS DRIVER L: [email protected] S: OrphanDocumentation/.renames.txt +0
-2@@ -783,7 +783,6 @@ namespaces/compatibility-list admin-guide/namespaces/compatibility-list namespaces/index admin-guide/namespaces/index namespaces/resource-control admin-guide/namespaces/resource-control networking/altera_tse networking/device_drivers/ethernet/altera/altera_tse -networking/baycom networking/device_drivers/hamradio/baycom networking/bpf_flow_dissector bpf/prog_flow_dissector networking/cxacru networking/device_drivers/atm/cxacru networking/defza networking/device_drivers/fddi/defza@@ -846,7 +845,6 @@ networking/ixgbe networking/device_drivers/ethernet/intel/ixgbe networking/ixgbevf networking/device_drivers/ethernet/intel/ixgbevf networking/netdev-FAQ process/maintainer-netdev networking/skfp networking/device_drivers/fddi/skfp -networking/z8530drv networking/device_drivers/hamradio/z8530drv nfc/index driver-api/nfc/index nfc/nfc-hci driver-api/nfc/nfc-hci nfc/nfc-pn544 driver-api/nfc/nfc-pn544Documentation/admin-guide/kernel-parameters.txt +0
-18@@ -6,7 +6,6 @@ APPARMOR AppArmor support is enabled. ARM ARM architecture is enabled. ARM64 ARM64 architecture is enabled. - AX25 Appropriate AX.25 support is enabled. CLK Common clock infrastructure is enabled. CMA Contiguous Memory Area support is enabled. DRM Direct Rendering Management support is enabled.@@ -633,23 +632,6 @@ Kernel parameters 1 - Enable the BAU. unset - Disable the BAU. - baycom_epp= [HW,AX25] - Format: <io>,<mode> - - baycom_par= [HW,AX25] BayCom Parallel Port AX.25 Modem - Format: <io>,<mode> - See header of drivers/net/hamradio/baycom_par.c. - - baycom_ser_fdx= [HW,AX25] - BayCom Serial Port AX.25 Modem (Full Duplex Mode) - Format: <io>,<irq>,<mode>[,<baud>] - See header of drivers/net/hamradio/baycom_ser_fdx.c. - - baycom_ser_hdx= [HW,AX25] - BayCom Serial Port AX.25 Modem (Half Duplex Mode) - Format: <io>,<irq>,<mode> - See header of drivers/net/hamradio/baycom_ser_hdx.c. - bdev_allow_write_mounted= Format: <bool> Control the ability to open a mounted block deviceDocumentation/networking/6pack.rst deleted +0
-191@@ -1,191 +0,0 @@ -.. SPDX-License-Identifier: GPL-2.0 - -============== -6pack Protocol -============== - -This is the 6pack-mini-HOWTO, written by - -Andreas Könsgen DG3KQ - -:Internet: [email protected] -:AMPR-net: [email protected] -:AX.25: dg3kq@db0ach.#nrw.deu.eu - -Last update: April 7, 1998 - -1. What is 6pack, and what are the advantages to KISS? -====================================================== - -6pack is a transmission protocol for data exchange between the PC and -the TNC over a serial line. It can be used as an alternative to KISS. - -6pack has two major advantages: - -- The PC is given full control over the radio - channel. Special control data is exchanged between the PC and the TNC so - that the PC knows at any time if the TNC is receiving data, if a TNC - buffer underrun or overrun has occurred, if the PTT is - set and so on. This control data is processed at a higher priority than - normal data, so a data stream can be interrupted at any time to issue an - important event. This helps to improve the channel access and timing - algorithms as everything is computed in the PC. It would even be possible - to experiment with something completely different from the known CSMA and - DAMA channel access methods. - This kind of real-time control is especially important to supply several - TNCs that are connected between each other and the PC by a daisy chain - (however, this feature is not supported yet by the Linux 6pack driver). - -- Each packet transferred over the serial line is supplied with a checksum, - so it is easy to detect errors due to problems on the serial line. - Received packets that are corrupt are not passed on to the AX.25 layer. - Damaged packets that the TNC has received from the PC are not transmitted. - -More details about 6pack are described in the file 6pack.ps that is located -in the doc directory of the AX.25 utilities package. - -2. Who has developed the 6pack protocol? -======================================== - -The 6pack protocol has been developed by Ekki Plicht DF4OR, Henning Rech -DF9IC and Gunter Jost DK7WJ. A driver for 6pack, written by Gunter Jost and -Matthias Welwarsky DG2FEF, comes along with the PC version of FlexNet. -They have also written a firmware for TNCs to perform the 6pack -protocol (see section 4 below). - -3. Where can I get the latest version of 6pack for LinuX? -========================================================= - -At the moment, the 6pack stuff can obtained via anonymous ftp from -db0bm.automation.fh-aachen.de. In the directory /incoming/dg3kq, -there is a file named 6pack.tgz. - -4. Preparing the TNC for 6pack operation -======================================== - -To be able to use 6pack, a special firmware for the TNC is needed. The EPROM -of a newly bought TNC does not contain 6pack, so you will have to -program an EPROM yourself. The image file for 6pack EPROMs should be -available on any packet radio box where PC/FlexNet can be found. The name of -the file is 6pack.bin. This file is copyrighted and maintained by the FlexNet -team. It can be used under the terms of the license that comes along -with PC/FlexNet. Please do not ask me about the internals of this file as I -don't know anything about it. I used a textual description of the 6pack -protocol to program the Linux driver. - -TNCs contain a 64kByte EPROM, the lower half of which is used for -the firmware/KISS. The upper half is either empty or is sometimes -programmed with software called TAPR. In the latter case, the TNC -is supplied with a DIP switch so you can easily change between the -two systems. When programming a new EPROM, one of the systems is replaced -by 6pack. It is useful to replace TAPR, as this software is rarely used -nowadays. If your TNC is not equipped with the switch mentioned above, you -can build in one yourself that switches over the highest address pin -of the EPROM between HIGH and LOW level. After having inserted the new EPROM -and switched to 6pack, apply power to the TNC for a first test. The connect -and the status LED are lit for about a second if the firmware initialises -the TNC correctly. - -5. Building and installing the 6pack driver -=========================================== - -The driver has been tested with kernel version 2.1.90. Use with older -kernels may lead to a compilation error because the interface to a kernel -function has been changed in the 2.1.8x kernels. - -How to turn on 6pack support: ------------------------------ - -- In the linux kernel configuration program, select the code maturity level - options menu and turn on the prompting for development drivers. - -- Select the amateur radio support menu and turn on the serial port 6pack - driver. - -- Compile and install the kernel and the modules. - -To use the driver, the kissattach program delivered with the AX.25 utilities -has to be modified. - -- Do a cd to the directory that holds the kissattach sources. Edit the - kissattach.c file. At the top, insert the following lines:: - - #ifndef N_6PACK - #define N_6PACK (N_AX25+1) - #endif - - Then find the line: - - int disc = N_AX25; - - and replace N_AX25 by N_6PACK. - -- Recompile kissattach. Rename it to spattach to avoid confusions. - -Installing the driver: ----------------------- - -- Do an insmod 6pack. Look at your /var/log/messages file to check if the - module has printed its initialization message. - -- Do a spattach as you would launch kissattach when starting a KISS port. - Check if the kernel prints the message '6pack: TNC found'. - -- From here, everything should work as if you were setting up a KISS port. - The only difference is that the network device that represents - the 6pack port is called sp instead of sl or ax. So, sp0 would be the - first 6pack port. - -Although the driver has been tested on various platforms, I still declare it -ALPHA. BE CAREFUL! Sync your disks before insmoding the 6pack module -and spattaching. Watch out if your computer behaves strangely. Read section -6 of this file about known problems. - -Note that the connect and status LEDs of the TNC are controlled in a -different way than they are when the TNC is used with PC/FlexNet. When using -FlexNet, the connect LED is on if there is a connection; the status LED is -on if there is data in the buffer of the PC's AX.25 engine that has to be -transmitted. Under Linux, the 6pack layer is beyond the AX.25 layer, -so the 6pack driver doesn't know anything about connects or data that -has not yet been transmitted. Therefore the LEDs are controlled -as they are in KISS mode: The connect LED is turned on if data is transferred -from the PC to the TNC over the serial line, the status LED if data is -sent to the PC. - -6. Known problems -================= - -When testing the driver with 2.0.3x kernels and -operating with data rates on the radio channel of 9600 Baud or higher, -the driver may, on certain systems, sometimes print the message '6pack: -bad checksum', which is due to data loss if the other station sends two -or more subsequent packets. I have been told that this is due to a problem -with the serial driver of 2.0.3x kernels. I don't know yet if the problem -still exists with 2.1.x kernels, as I have heard that the serial driver -code has been changed with 2.1.x. - -When shutting down the sp interface with ifconfig, the kernel crashes if -there is still an AX.25 connection left over which an IP connection was -running, even if that IP connection is already closed. The problem does not -occur when there is a bare AX.25 connection still running. I don't know if -this is a problem of the 6pack driver or something else in the kernel. - -The driver has been tested as a module, not yet as a kernel-builtin driver. - -The 6pack protocol supports daisy-chaining of TNCs in a token ring, which is -connected to one serial port of the PC. This feature is not implemented -and at least at the moment I won't be able to do it because I do not have -the opportunity to build a TNC daisy-chain and test it. - -Some of the comments in the source code are inaccurate. They are left from -the SLIP/KISS driver, from which the 6pack driver has been derived. -I haven't modified or removed them yet -- sorry! The code itself needs -some cleaning and optimizing. This will be done in a later release. - -If you encounter a bug or if you have a question or suggestion concerning the -driver, feel free to mail me, using the addresses given at the beginning of -this file. - -Have fun! - -AndreasDocumentation/networking/ax25.rst deleted +0
-17@@ -1,17 +0,0 @@ -.. SPDX-License-Identifier: GPL-2.0 - -===== -AX.25 -===== - -To use the amateur radio protocols within Linux you will need to get a -suitable copy of the AX.25 Utilities. More detailed information about -AX.25, NET/ROM and ROSE, associated programs and utilities can be -found on https://linux-ax25.in-berlin.de. - -There is a mailing list for discussing Linux amateur radio matters -called [email protected]. To subscribe to it, send a message to [email protected] or use the web interface at -https://vger.kernel.org. The subject and body of the message are -ignored. You don't need to be subscribed to post but of course that -means you might miss an answer.Documentation/networking/device_drivers/hamradio/baycom.rst deleted +0
-174@@ -1,174 +0,0 @@ -.. SPDX-License-Identifier: GPL-2.0 - -=============================== -Linux Drivers for Baycom Modems -=============================== - -Thomas M. Sailer, HB9JNX/AE4WA, <[email protected]> - -The drivers for the baycom modems have been split into -separate drivers as they did not share any code, and the driver -and device names have changed. - -This document describes the Linux Kernel Drivers for simple Baycom style -amateur radio modems. - -The following drivers are available: -==================================== - -baycom_ser_fdx: - This driver supports the SER12 modems either full or half duplex. - Its baud rate may be changed via the ``baud`` module parameter, - therefore it supports just about every bit bang modem on a - serial port. Its devices are called bcsf0 through bcsf3. - This is the recommended driver for SER12 type modems, - however if you have a broken UART clone that does not have working - delta status bits, you may try baycom_ser_hdx. - -baycom_ser_hdx: - This is an alternative driver for SER12 type modems. - It only supports half duplex, and only 1200 baud. Its devices - are called bcsh0 through bcsh3. Use this driver only if baycom_ser_fdx - does not work with your UART. - -baycom_par: - This driver supports the par96 and picpar modems. - Its devices are called bcp0 through bcp3. - -baycom_epp: - This driver supports the EPP modem. - Its devices are called bce0 through bce3. - This driver is work-in-progress. - -The following modems are supported: - -======= ======================================================================== -ser12 This is a very simple 1200 baud AFSK modem. The modem consists only - of a modulator/demodulator chip, usually a TI TCM3105. The computer - is responsible for regenerating the receiver bit clock, as well as - for handling the HDLC protocol. The modem connects to a serial port, - hence the name. Since the serial port is not used as an async serial - port, the kernel driver for serial ports cannot be used, and this - driver only supports standard serial hardware (8250, 16450, 16550) - -par96 This is a modem for 9600 baud FSK compatible to the G3RUH standard. - The modem does all the filtering and regenerates the receiver clock. - Data is transferred from and to the PC via a shift register. - The shift register is filled with 16 bits and an interrupt is signalled. - The PC then empties the shift register in a burst. This modem connects - to the parallel port, hence the name. The modem leaves the - implementation of the HDLC protocol and the scrambler polynomial to - the PC. - -picpar This is a redesign of the par96 modem by Henning Rech, DF9IC. The modem - is protocol compatible to par96, but uses only three low power ICs - and can therefore be fed from the parallel port and does not require - an additional power supply. Furthermore, it incorporates a carrier - detect circuitry. - -EPP This is a high-speed modem adaptor that connects to an enhanced parallel - port. - - Its target audience is users working over a high speed hub (76.8kbit/s). - -eppfpga This is a redesign of the EPP adaptor. -======= ======================================================================== - -All of the above modems only support half duplex communications. However, -the driver supports the KISS (see below) fullduplex command. It then simply -starts to send as soon as there's a packet to transmit and does not care -about DCD, i.e. it starts to send even if there's someone else on the channel. -This command is required by some implementations of the DAMA channel -access protocol. - - -The Interface of the drivers -============================ - -Unlike previous drivers, these drivers are no longer character devices, -but they are now true kernel network interfaces. Installation is therefore -simple. Once installed, four interfaces named bc{sf,sh,p,e}[0-3] are available. -sethdlc from the ax25 utilities may be used to set driver states etc. -Users of userland AX.25 stacks may use the net2kiss utility (also available -in the ax25 utilities package) to convert packets of a network interface -to a KISS stream on a pseudo tty. There's also a patch available from -me for WAMPES which allows attaching a kernel network interface directly. - - -Configuring the driver -====================== - -Every time a driver is inserted into the kernel, it has to know which -modems it should access at which ports. This can be done with the setbaycom -utility. If you are only using one modem, you can also configure the -driver from the insmod command line (or by means of an option line in -``/etc/modprobe.d/*.conf``). - -Examples:: - - modprobe baycom_ser_fdx mode="ser12*" iobase=0x3f8 irq=4 - sethdlc -i bcsf0 -p mode "ser12*" io 0x3f8 irq 4 - -Both lines configure the first port to drive a ser12 modem at the first -serial port (COM1 under DOS). The * in the mode parameter instructs the driver -to use the software DCD algorithm (see below):: - - insmod baycom_par mode="picpar" iobase=0x378 - sethdlc -i bcp0 -p mode "picpar" io 0x378 - -Both lines configure the first port to drive a picpar modem at the -first parallel port (LPT1 under DOS). (Note: picpar implies -hardware DCD, par96 implies software DCD). - -The channel access parameters can be set with sethdlc -a or kissparms. -Note that both utilities interpret the values slightly differently. - - -Hardware DCD versus Software DCD -================================ - -To avoid collisions on the air, the driver must know when the channel is -busy. This is the task of the DCD circuitry/software. The driver may either -utilise a software DCD algorithm (options=1) or use a DCD signal from -the hardware (options=0). - -======= ================================================================= -ser12 if software DCD is utilised, the radio's squelch should always be - open. It is highly recommended to use the software DCD algorithm, - as it is much faster than most hardware squelch circuitry. The - disadvantage is a slightly higher load on the system. - -par96 the software DCD algorithm for this type of modem is rather poor. - The modem simply does not provide enough information to implement - a reasonable DCD algorithm in software. Therefore, if your radio - feeds the DCD input of the PAR96 modem, the use of the hardware - DCD circuitry is recommended. - -picpar the picpar modem features a builtin DCD hardware, which is highly - recommended. -======= ================================================================= - - - -Compatibility with the rest of the Linux kernel -=============================================== - -The serial driver and the baycom serial drivers compete -for the same hardware resources. Of course only one driver can access a given -interface at a time. The serial driver grabs all interfaces it can find at -startup time. Therefore the baycom drivers subsequently won't be able to -access a serial port. You might therefore find it necessary to release -a port owned by the serial driver with 'setserial /dev/ttyS# uart none', where -# is the number of the interface. The baycom drivers do not reserve any -ports at startup, unless one is specified on the 'insmod' command line. Another -method to solve the problem is to compile all drivers as modules and -leave it to kmod to load the correct driver depending on the application. - -The parallel port drivers (baycom_par, baycom_epp) now use the parport subsystem -to arbitrate the ports between different client drivers. - -vy 73s de - -Tom Sailer, [email protected] - -hb9jnx @ hb9w.ampr.orgDocumentation/networking/device_drivers/hamradio/index.rst deleted +0
-12@@ -1,12 +0,0 @@ -.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) - -Amateur Radio Device Drivers -============================ - -Contents: - -.. toctree:: - :maxdepth: 2 - - baycom - z8530drvDocumentation/networking/device_drivers/hamradio/z8530drv.rst deleted +0
-686@@ -1,686 +0,0 @@ -.. SPDX-License-Identifier: GPL-2.0 -.. include:: <isonum.txt> - -========================================================= -SCC.C - Linux driver for Z8530 based HDLC cards for AX.25 -========================================================= - - -This is a subset of the documentation. To use this driver you MUST have the -full package from: - -Internet: - - 1. ftp://ftp.ccac.rwth-aachen.de/pub/jr/z8530drv-utils_3.0-3.tar.gz - - 2. ftp://ftp.pspt.fi/pub/ham/linux/ax25/z8530drv-utils_3.0-3.tar.gz - -Please note that the information in this document may be hopelessly outdated. -A new version of the documentation, along with links to other important -Linux Kernel AX.25 documentation and programs, is available on -http://yaina.de/jreuter - -Copyright |copy| 1993,2000 by Joerg Reuter DL1BKE <[email protected]> - -portions Copyright |copy| 1993 Guido ten Dolle PE1NNZ - -for the complete copyright notice see >> Copying.Z8530DRV << - -1. Initialization of the driver -=============================== - -To use the driver, 3 steps must be performed: - - 1. if compiled as module: loading the module - 2. Setup of hardware, MODEM and KISS parameters with sccinit - 3. Attach each channel to the Linux kernel AX.25 with "ifconfig" - -Unlike the versions below 2.4 this driver is a real network device -driver. If you want to run xNOS instead of our fine kernel AX.25 -use a 2.x version (available from above sites) or read the -AX.25-HOWTO on how to emulate a KISS TNC on network device drivers. - - -1.1 Loading the module -====================== - -(If you're going to compile the driver as a part of the kernel image, - skip this chapter and continue with 1.2) - -Before you can use a module, you'll have to load it with:: - - insmod scc.o - -please read 'man insmod' that comes with module-init-tools. - -You should include the insmod in one of the /etc/rc.d/rc.* files, -and don't forget to insert a call of sccinit after that. It -will read your /etc/z8530drv.conf. - -1.2. /etc/z8530drv.conf -======================= - -To setup all parameters you must run /sbin/sccinit from one -of your rc.*-files. This has to be done BEFORE you can -"ifconfig" an interface. Sccinit reads the file /etc/z8530drv.conf -and sets the hardware, MODEM and KISS parameters. A sample file is -delivered with this package. Change it to your needs. - -The file itself consists of two main sections. - -1.2.1 configuration of hardware parameters -========================================== - -The hardware setup section defines the following parameters for each -Z8530:: - - chip 1 - data_a 0x300 # data port A - ctrl_a 0x304 # control port A - data_b 0x301 # data port B - ctrl_b 0x305 # control port B - irq 5 # IRQ No. 5 - pclock 4915200 # clock - board BAYCOM # hardware type - escc no # enhanced SCC chip? (8580/85180/85280) - vector 0 # latch for interrupt vector - special no # address of special function register - option 0 # option to set via sfr - - -chip - - this is just a delimiter to make sccinit a bit simpler to - program. A parameter has no effect. - -data_a - - the address of the data port A of this Z8530 (needed) -ctrl_a - - the address of the control port A (needed) -data_b - - the address of the data port B (needed) -ctrl_b - - the address of the control port B (needed) - -irq - - the used IRQ for this chip. Different chips can use different - IRQs or the same. If they share an interrupt, it needs to be - specified within one chip-definition only. - -pclock - the clock at the PCLK pin of the Z8530 (option, 4915200 is - default), measured in Hertz - -board - - the "type" of the board: - - ======================= ======== - SCC type value - ======================= ======== - PA0HZP SCC card PA0HZP - EAGLE card EAGLE - PC100 card PC100 - PRIMUS-PC (DG9BL) card PRIMUS - BayCom (U)SCC card BAYCOM - ======================= ======== - -escc - - if you want support for ESCC chips (8580, 85180, 85280), set - this to "yes" (option, defaults to "no") - -vector - - address of the vector latch (aka "intack port") for PA0HZP - cards. There can be only one vector latch for all chips! - (option, defaults to 0) - -special - - address of the special function register on several cards. - (option, defaults to 0) - -option - The value you write into that register (option, default is 0) - -You can specify up to four chips (8 channels). If this is not enough, -just change:: - - #define MAXSCC 4 - -to a higher value. - -Example for the BAYCOM USCC: ----------------------------- - -:: - - chip 1 - data_a 0x300 # data port A - ctrl_a 0x304 # control port A - data_b 0x301 # data port B - ctrl_b 0x305 # control port B - irq 5 # IRQ No. 5 (#) - board BAYCOM # hardware type (*) - # - # SCC chip 2 - # - chip 2 - data_a 0x302 - ctrl_a 0x306 - data_b 0x303 - ctrl_b 0x307 - board BAYCOM - -An example for a PA0HZP card: ------------------------------ - -:: - - chip 1 - data_a 0x153 - data_b 0x151 - ctrl_a 0x152 - ctrl_b 0x150 - irq 9 - pclock 4915200 - board PA0HZP - vector 0x168 - escc no - # - # - # - chip 2 - data_a 0x157 - data_b 0x155 - ctrl_a 0x156 - ctrl_b 0x154 - irq 9 - pclock 4915200 - board PA0HZP - vector 0x168 - escc no - -A DRSI would should probably work with this: --------------------------------------------- -(actually: two DRSI cards...) - -:: - - chip 1 - data_a 0x303 - data_b 0x301 - ctrl_a 0x302 - ctrl_b 0x300 - irq 7 - pclock 4915200 - board DRSI - escc no - # - # - # - chip 2 - data_a 0x313 - data_b 0x311 - ctrl_a 0x312 - ctrl_b 0x310 - irq 7 - pclock 4915200 - board DRSI - escc no - -Note that you cannot use the on-board baudrate generator off DRSI -cards. Use "mode dpll" for clock source (see below). - -This is based on information provided by Mike Bilow (and verified -by Paul Helay) - -The utility "gencfg" --------------------- - -If you only know the parameters for the PE1CHL driver for DOS, -run gencfg. It will generate the correct port addresses (I hope). -Its parameters are exactly the same as the ones you use with -the "attach scc" command in net, except that the string "init" must -not appear. Example:: - - gencfg 2 0x150 4 2 0 1 0x168 9 4915200 - -will print a skeleton z8530drv.conf for the OptoSCC to stdout. - -:: - - gencfg 2 0x300 2 4 5 -4 0 7 4915200 0x10 - -does the same for the BAYCOM USCC card. In my opinion it is much easier -to edit scc_config.h... - - -1.2.2 channel configuration -=========================== - -The channel definition is divided into three sub sections for each -channel: - -An example for scc0:: - - # DEVICE - - device scc0 # the device for the following params - - # MODEM / BUFFERS - - speed 1200 # the default baudrate - clock dpll # clock source: - # dpll = normal half duplex operation - # external = MODEM provides own Rx/Tx clock - # divider = use full duplex divider if - # installed (1) - mode nrzi # HDLC encoding mode - # nrzi = 1k2 MODEM, G3RUH 9k6 MODEM - # nrz = DF9IC 9k6 MODEM - # - bufsize 384 # size of buffers. Note that this must include - # the AX.25 header, not only the data field! - # (optional, defaults to 384) - - # KISS (Layer 1) - - txdelay 36 # (see chapter 1.4) - persist 64 - slot 8 - tail 8 - fulldup 0 - wait 12 - min 3 - maxkey 7 - idle 3 - maxdef 120 - group 0 - txoff off - softdcd on - slip off - -The order WITHIN these sections is unimportant. The order OF these -sections IS important. The MODEM parameters are set with the first -recognized KISS parameter... - -Please note that you can initialize the board only once after boot -(or insmod). You can change all parameters but "mode" and "clock" -later with the Sccparam program or through KISS. Just to avoid -security holes... - -(1) this divider is usually mounted on the SCC-PBC (PA0HZP) or not - present at all (BayCom). It feeds back the output of the DPLL - (digital pll) as transmit clock. Using this mode without a divider - installed will normally result in keying the transceiver until - maxkey expires --- of course without sending anything (useful). - -2. Attachment of a channel by your AX.25 software -================================================= - -2.1 Kernel AX.25 -================ - -To set up an AX.25 device you can simply type:: - - ifconfig scc0 44.128.1.1 hw ax25 dl0tha-7 - -This will create a network interface with the IP number 44.128.20.107 -and the callsign "dl0tha". If you do not have any IP number (yet) you -can use any of the 44.128.0.0 network. Note that you do not need -axattach. The purpose of axattach (like slattach) is to create a KISS -network device linked to a TTY. Please read the documentation of the -ax25-utils and the AX.25-HOWTO to learn how to set the parameters of -the kernel AX.25. - -2.2 NOS, NET and TFKISS -======================= - -Since the TTY driver (aka KISS TNC emulation) is gone you need -to emulate the old behaviour. The cost of using these programs is -that you probably need to compile the kernel AX.25, regardless of whether -you actually use it or not. First setup your /etc/ax25/axports, -for example:: - - 9k6 dl0tha-9 9600 255 4 9600 baud port (scc3) - axlink dl0tha-15 38400 255 4 Link to NOS - -Now "ifconfig" the scc device:: - - ifconfig scc3 44.128.1.1 hw ax25 dl0tha-9 - -You can now axattach a pseudo-TTY:: - - axattach /dev/ptys0 axlink - -and start your NOS and attach /dev/ptys0 there. The problem is that -NOS is reachable only via digipeating through the kernel AX.25 -(disastrous on a DAMA controlled channel). To solve this problem, -configure "rxecho" to echo the incoming frames from "9k6" to "axlink" -and outgoing frames from "axlink" to "9k6" and start:: - - rxecho - -Or simply use "kissbridge" coming with z8530drv-utils:: - - ifconfig scc3 hw ax25 dl0tha-9 - kissbridge scc3 /dev/ptys0 - - -3. Adjustment and Display of parameters -======================================= - -3.1 Displaying SCC Parameters: -============================== - -Once a SCC channel has been attached, the parameter settings and -some statistic information can be shown using the param program:: - - dl1bke-u:~$ sccstat scc0 - - Parameters: - - speed : 1200 baud - txdelay : 36 - persist : 255 - slottime : 0 - txtail : 8 - fulldup : 1 - waittime : 12 - mintime : 3 sec - maxkeyup : 7 sec - idletime : 3 sec - maxdefer : 120 sec - group : 0x00 - txoff : off - softdcd : on - SLIP : off - - Status: - - HDLC Z8530 Interrupts Buffers - ----------------------------------------------------------------------- - Sent : 273 RxOver : 0 RxInts : 125074 Size : 384 - Received : 1095 TxUnder: 0 TxInts : 4684 NoSpace : 0 - RxErrors : 1591 ExInts : 11776 - TxErrors : 0 SpInts : 1503 - Tx State : idle - - -The status info shown is: - -============== ============================================================== -Sent number of frames transmitted -Received number of frames received -RxErrors number of receive errors (CRC, ABORT) -TxErrors number of discarded Tx frames (due to various reasons) -Tx State status of the Tx interrupt handler: idle/busy/active/tail (2) -RxOver number of receiver overruns -TxUnder number of transmitter underruns -RxInts number of receiver interrupts -TxInts number of transmitter interrupts -EpInts number of receiver special condition interrupts -SpInts number of external/status interrupts -Size maximum size of an AX.25 frame (*with* AX.25 headers!) -NoSpace number of times a buffer could not get allocated -============== ============================================================== - -An overrun is abnormal. If lots of these occur, the product of -baudrate and number of interfaces is too high for the processing -power of your computer. NoSpace errors are unlikely to be caused by the -driver or the kernel AX.25. - - -3.2 Setting Parameters -====================== - - -The setting of parameters of the emulated KISS TNC is done in the -same way in the SCC driver. You can change parameters by using -the kissparms program from the ax25-utils package or use the program -"sccparam":: - - sccparam <device> <paramname> <decimal-|hexadecimal value> - -You can change the following parameters: - -=========== ===== -param value -=========== ===== -speed 1200 -txdelay 36 -persist 255 -slottime 0 -txtail 8 -fulldup 1 -waittime 12 -mintime 3 -maxkeyup 7 -idletime 3 -maxdefer 120 -group 0x00 -txoff off -softdcd on -SLIP off -=========== ===== - - -The parameters have the following meaning: - -speed: - The baudrate on this channel in bits/sec - - Example: sccparam /dev/scc3 speed 9600 - -txdelay: - The delay (in units of 10 ms) after keying of the - transmitter, until the first byte is sent. This is usually - called "TXDELAY" in a TNC. When 0 is specified, the driver - will just wait until the CTS signal is asserted. This - assumes the presence of a timer or other circuitry in the - MODEM and/or transmitter, that asserts CTS when the - transmitter is ready for data. - A normal value of this parameter is 30-36. - - Example: sccparam /dev/scc0 txd 20 - -persist: - This is the probability that the transmitter will be keyed - when the channel is found to be free. It is a value from 0 - to 255, and the probability is (value+1)/256. The value - should be somewhere near 50-60, and should be lowered when - the channel is used more heavily. - - Example: sccparam /dev/scc2 persist 20 - -slottime: - This is the time between samples of the channel. It is - expressed in units of 10 ms. About 200-300 ms (value 20-30) - seems to be a good value. - - Example: sccparam /dev/scc0 slot 20 - -tail: - The time the transmitter will remain keyed after the last - byte of a packet has been transferred to the SCC. This is - necessary because the CRC and a flag still have to leave the - SCC before the transmitter is keyed down. The value depends - on the baudrate selected. A few character times should be - sufficient, e.g. 40ms at 1200 baud. (value 4) - The value of this parameter is in 10 ms units. - - Example: sccparam /dev/scc2 4 - -full: - The full-duplex mode switch. This can be one of the following - values: - - 0: The interface will operate in CSMA mode (the normal - half-duplex packet radio operation) - 1: Fullduplex mode, i.e. the transmitter will be keyed at - any time, without checking the received carrier. It - will be unkeyed when there are no packets to be sent. - 2: Like 1, but the transmitter will remain keyed, also - when there are no packets to be sent. Flags will be - sent in that case, until a timeout (parameter 10) - occurs. - - Example: sccparam /dev/scc0 fulldup off - -wait: - The initial waittime before any transmit attempt, after the - frame has been queue for transmit. This is the length of - the first slot in CSMA mode. In full duplex modes it is - set to 0 for maximum performance. - The value of this parameter is in 10 ms units. - - Example: sccparam /dev/scc1 wait 4 - -maxkey: - The maximal time the transmitter will be keyed to send - packets, in seconds. This can be useful on busy CSMA - channels, to avoid "getting a bad reputation" when you are - generating a lot of traffic. After the specified time has - elapsed, no new frame will be started. Instead, the trans- - mitter will be switched off for a specified time (parameter - min), and then the selected algorithm for keyup will be - started again. - The value 0 as well as "off" will disable this feature, - and allow infinite transmission time. - - Example: sccparam /dev/scc0 maxk 20 - -min: - This is the time the transmitter will be switched off when - the maximum transmission time is exceeded. - - Example: sccparam /dev/scc3 min 10 - -idle: - This parameter specifies the maximum idle time in full duplex - 2 mode, in seconds. When no frames have been sent for this - time, the transmitter will be keyed down. A value of 0 is - has same result as the fullduplex mode 1. This parameter - can be disabled. - - Example: sccparam /dev/scc2 idle off # transmit forever - -maxdefer - This is the maximum time (in seconds) to wait for a free channel - to send. When this timer expires the transmitter will be keyed - IMMEDIATELY. If you love to get trouble with other users you - should set this to a very low value ;-) - - Example: sccparam /dev/scc0 maxdefer 240 # 2 minutes - - -txoff: - When this parameter has the value 0, the transmission of packets - is enable. Otherwise it is disabled. - - Example: sccparam /dev/scc2 txoff on - -group: - It is possible to build special radio equipment to use more than - one frequency on the same band, e.g. using several receivers and - only one transmitter that can be switched between frequencies. - Also, you can connect several radios that are active on the same - band. In these cases, it is not possible, or not a good idea, to - transmit on more than one frequency. The SCC driver provides a - method to lock transmitters on different interfaces, using the - "param <interface> group <x>" command. This will only work when - you are using CSMA mode (parameter full = 0). - - The number <x> must be 0 if you want no group restrictions, and - can be computed as follows to create restricted groups: - <x> is the sum of some OCTAL numbers: - - - === ======================================================= - 200 This transmitter will only be keyed when all other - transmitters in the group are off. - 100 This transmitter will only be keyed when the carrier - detect of all other interfaces in the group is off. - 0xx A byte that can be used to define different groups. - Interfaces are in the same group, when the logical AND - between their xx values is nonzero. - === ======================================================= - - Examples: - - When 2 interfaces use group 201, their transmitters will never be - keyed at the same time. - - When 2 interfaces use group 101, the transmitters will only key - when both channels are clear at the same time. When group 301, - the transmitters will not be keyed at the same time. - - Don't forget to convert the octal numbers into decimal before - you set the parameter. - - Example: (to be written) - -softdcd: - use a software dcd instead of the real one... Useful for a very - slow squelch. - - Example: sccparam /dev/scc0 soft on - - -4. Problems -=========== - -If you have tx-problems with your BayCom USCC card please check -the manufacturer of the 8530. SGS chips have a slightly -different timing. Try Zilog... A solution is to write to register 8 -instead to the data port, but this won't work with the ESCC chips. -*SIGH!* - -A very common problem is that the PTT locks until the maxkeyup timer -expires, although interrupts and clock source are correct. In most -cases compiling the driver with CONFIG_SCC_DELAY (set with -make config) solves the problems. For more hints read the (pseudo) FAQ -and the documentation coming with z8530drv-utils. - -I got reports that the driver has problems on some 386-based systems. -(i.e. Amstrad) Those systems have a bogus AT bus timing which will -lead to delayed answers on interrupts. You can recognize these -problems by looking at the output of Sccstat for the suspected -port. If it shows under- and overruns you own such a system. - -Delayed processing of received data: This depends on - -- the kernel version - -- kernel profiling compiled or not - -- a high interrupt load - -- a high load of the machine --- running X, Xmorph, XV and Povray, - while compiling the kernel... hmm ... even with 32 MB RAM ... ;-) - Or running a named for the whole .ampr.org domain on an 8 MB - box... - -- using information from rxecho or kissbridge. - -Kernel panics: please read /linux/README and find out if it -really occurred within the scc driver. - -If you cannot solve a problem, send me - -- a description of the problem, -- information on your hardware (computer system, scc board, modem) -- your kernel version -- the output of cat /proc/net/z8530 - -4. Thor RLC100 -============== - -Mysteriously this board seems not to work with the driver. Anyone -got it up-and-running? - - -Many thanks to Linus Torvalds and Alan Cox for including the driver -in the Linux standard distribution and their support. - -:: - - Joerg Reuter ampr-net: [email protected] - AX-25 : DL1BKE @ DB0ABH.#BAY.DEU.EU - Internet: [email protected] - WWW : http://yaina.de/jreuterDocumentation/networking/device_drivers/index.rst +0
-1@@ -13,6 +13,5 @@ Hardware Device Drivers cellular/index ethernet/index fddi/index - hamradio/index wifi/index wwan/indexDocumentation/networking/index.rst +0
-2@@ -40,11 +40,9 @@ Refer to :ref:`netdev-FAQ` for a guide on netdev development process specifics. tls-handshake nfc 6lowpan - 6pack arcnet-hardware arcnet atm - ax25 bonding cdc_mbim dctcpDocumentation/staging/magic-number.rst +0
-3@@ -72,11 +72,8 @@ PG_MAGIC 'P' pg_{read,write}_hdr ``include/uapi/l APM_BIOS_MAGIC 0x4101 apm_user ``arch/x86/kernel/apm_32.c`` FASYNC_MAGIC 0x4601 fasync_struct ``include/linux/fs.h`` SLIP_MAGIC 0x5302 slip ``drivers/net/slip/slip.h`` -BAYCOM_MAGIC 19730510 baycom_state ``drivers/net/hamradio/baycom_epp.c`` -HDLCDRV_MAGIC 0x5ac6e778 hdlcdrv_state ``include/linux/hdlcdrv.h`` KV_MAGIC 0x5f4b565f kernel_vars_s ``arch/mips/include/asm/sn/klkernvars.h`` CODA_MAGIC 0xC0DAC0DA coda_file_info ``fs/coda/coda_fs_i.h`` -YAM_MAGIC 0xF10A7654 yam_port ``drivers/net/hamradio/yam.c`` CCB_MAGIC 0xf2691ad2 ccb ``drivers/scsi/ncr53c8xx.c`` QUEUE_MAGIC_FREE 0xf7e1c9a3 queue_entry ``drivers/scsi/arm/queue.c`` QUEUE_MAGIC_USED 0xf7e1cc33 queue_entry ``drivers/scsi/arm/queue.c``Documentation/translations/it_IT/staging/magic-number.rst +0
-3@@ -78,11 +78,8 @@ PG_MAGIC 'P' pg_{read,write}_hdr ``include/linux/ APM_BIOS_MAGIC 0x4101 apm_user ``arch/x86/kernel/apm_32.c`` FASYNC_MAGIC 0x4601 fasync_struct ``include/linux/fs.h`` SLIP_MAGIC 0x5302 slip ``drivers/net/slip.h`` -BAYCOM_MAGIC 0x19730510 baycom_state ``drivers/net/baycom_epp.c`` -HDLCDRV_MAGIC 0x5ac6e778 hdlcdrv_state ``include/linux/hdlcdrv.h`` KV_MAGIC 0x5f4b565f kernel_vars_s ``arch/mips/include/asm/sn/klkernvars.h`` CODA_MAGIC 0xC0DAC0DA coda_file_info ``fs/coda/coda_fs_i.h`` -YAM_MAGIC 0xF10A7654 yam_port ``drivers/net/hamradio/yam.c`` CCB_MAGIC 0xf2691ad2 ccb ``drivers/scsi/ncr53c8xx.c`` QUEUE_MAGIC_FREE 0xf7e1c9a3 queue_entry ``drivers/scsi/arm/queue.c`` QUEUE_MAGIC_USED 0xf7e1cc33 queue_entry ``drivers/scsi/arm/queue.c``Documentation/translations/sp_SP/process/magic-number.rst +0
-3@@ -77,11 +77,8 @@ PG_MAGIC 'P' pg_{read,write}_hdr ``include/linux/ APM_BIOS_MAGIC 0x4101 apm_user ``arch/x86/kernel/apm_32.c`` FASYNC_MAGIC 0x4601 fasync_struct ``include/linux/fs.h`` SLIP_MAGIC 0x5302 slip ``drivers/net/slip.h`` -BAYCOM_MAGIC 0x19730510 baycom_state ``drivers/net/baycom_epp.c`` -HDLCDRV_MAGIC 0x5ac6e778 hdlcdrv_state ``include/linux/hdlcdrv.h`` KV_MAGIC 0x5f4b565f kernel_vars_s ``arch/mips/include/asm/sn/klkernvars.h`` CODA_MAGIC 0xC0DAC0DA coda_file_info ``fs/coda/coda_fs_i.h`` -YAM_MAGIC 0xF10A7654 yam_port ``drivers/net/hamradio/yam.c`` CCB_MAGIC 0xf2691ad2 ccb ``drivers/scsi/ncr53c8xx.c`` QUEUE_MAGIC_FREE 0xf7e1c9a3 queue_entry ``drivers/scsi/arm/queue.c`` QUEUE_MAGIC_USED 0xf7e1cc33 queue_entry ``drivers/scsi/arm/queue.c``Documentation/translations/zh_CN/process/magic-number.rst +0
-3@@ -70,11 +70,8 @@ PG_MAGIC 'P' pg_{read,write}_hdr ``include/linux/ APM_BIOS_MAGIC 0x4101 apm_user ``arch/x86/kernel/apm_32.c`` FASYNC_MAGIC 0x4601 fasync_struct ``include/linux/fs.h`` SLIP_MAGIC 0x5302 slip ``drivers/net/slip.h`` -BAYCOM_MAGIC 0x19730510 baycom_state ``drivers/net/baycom_epp.c`` -HDLCDRV_MAGIC 0x5ac6e778 hdlcdrv_state ``include/linux/hdlcdrv.h`` KV_MAGIC 0x5f4b565f kernel_vars_s ``arch/mips/include/asm/sn/klkernvars.h`` CODA_MAGIC 0xC0DAC0DA coda_file_info ``fs/coda/coda_fs_i.h`` -YAM_MAGIC 0xF10A7654 yam_port ``drivers/net/hamradio/yam.c`` CCB_MAGIC 0xf2691ad2 ccb ``drivers/scsi/ncr53c8xx.c`` QUEUE_MAGIC_FREE 0xf7e1c9a3 queue_entry ``drivers/scsi/arm/queue.c`` QUEUE_MAGIC_USED 0xf7e1cc33 queue_entry ``drivers/scsi/arm/queue.c``Documentation/translations/zh_TW/process/magic-number.rst +0
-3@@ -64,11 +64,8 @@ PG_MAGIC 'P' pg_{read,write}_hdr ``include/linux/ APM_BIOS_MAGIC 0x4101 apm_user ``arch/x86/kernel/apm_32.c`` FASYNC_MAGIC 0x4601 fasync_struct ``include/linux/fs.h`` SLIP_MAGIC 0x5302 slip ``drivers/net/slip.h`` -BAYCOM_MAGIC 0x19730510 baycom_state ``drivers/net/baycom_epp.c`` -HDLCDRV_MAGIC 0x5ac6e778 hdlcdrv_state ``include/linux/hdlcdrv.h`` KV_MAGIC 0x5f4b565f kernel_vars_s ``arch/mips/include/asm/sn/klkernvars.h`` CODA_MAGIC 0xC0DAC0DA coda_file_info ``fs/coda/coda_fs_i.h`` -YAM_MAGIC 0xF10A7654 yam_port ``drivers/net/hamradio/yam.c`` CCB_MAGIC 0xf2691ad2 ccb ``drivers/scsi/ncr53c8xx.c`` QUEUE_MAGIC_FREE 0xf7e1c9a3 queue_entry ``drivers/scsi/arm/queue.c`` QUEUE_MAGIC_USED 0xf7e1cc33 queue_entry ``drivers/scsi/arm/queue.c``drivers/net/hamradio/Kconfig deleted +0
-162@@ -1,162 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -config MKISS - tristate "Serial port KISS driver" - depends on AX25 && TTY - select CRC16 - help - KISS is a protocol used for the exchange of data between a computer - and a Terminal Node Controller (a small embedded system commonly - used for networking over AX.25 amateur radio connections; it - connects the computer's serial port with the radio's microphone - input and speaker output). - - Although KISS is less advanced than the 6pack protocol, it has - the advantage that it is already supported by most modern TNCs - without the need for a firmware upgrade. - - To compile this driver as a module, choose M here: the module - will be called mkiss. - -config 6PACK - tristate "Serial port 6PACK driver" - depends on AX25 && TTY - help - 6pack is a transmission protocol for the data exchange between your - PC and your TNC (the Terminal Node Controller acts as a kind of - modem connecting your computer's serial port to your radio's - microphone input and speaker output). This protocol can be used as - an alternative to KISS for networking over AX.25 amateur radio - connections, but it has some extended functionality. - - Note that this driver is still experimental and might cause - problems. For details about the features and the usage of the - driver, read <file:Documentation/networking/6pack.rst>. - - To compile this driver as a module, choose M here: the module - will be called 6pack. - -config BPQETHER - tristate "BPQ Ethernet driver" - depends on AX25 - help - AX.25 is the protocol used for computer communication over amateur - radio. If you say Y here, you will be able to send and receive AX.25 - traffic over Ethernet (also called "BPQ AX.25"), which could be - useful if some other computer on your local network has a direct - amateur radio connection. - -config SCC - tristate "Z8530 SCC driver" - depends on ISA && AX25 - help - These cards are used to connect your Linux box to an amateur radio - in order to communicate with other computers. If you want to use - this, read - <file:Documentation/networking/device_drivers/hamradio/z8530drv.rst> - and the AX25-HOWTO, available from - <http://www.tldp.org/docs.html#howto>. Also make sure to say Y - to "Amateur Radio AX.25 Level 2" support. - - To compile this driver as a module, choose M here: the module - will be called scc. - -config SCC_DELAY - bool "additional delay for PA0HZP OptoSCC compatible boards" - depends on SCC - help - Say Y here if you experience problems with the SCC driver not - working properly; please read - <file:Documentation/networking/device_drivers/hamradio/z8530drv.rst> - for details. - - If unsure, say N. - -config SCC_TRXECHO - bool "support for TRX that feedback the tx signal to rx" - depends on SCC - help - Some transmitters feed the transmitted signal back to the receive - line. Say Y here to foil this by explicitly disabling the receiver - during data transmission. - - If in doubt, say Y. - -config BAYCOM_SER_FDX - tristate "BAYCOM ser12 fullduplex driver for AX.25" - depends on AX25 && HAS_IOPORT - select CRC_CCITT - help - This is one of two drivers for Baycom style simple amateur radio - modems that connect to a serial interface. The driver supports the - ser12 design in full-duplex mode. In addition, it allows the - baudrate to be set between 300 and 4800 baud (however not all modems - support all baudrates). This is the preferred driver. The next - driver, "BAYCOM ser12 half-duplex driver for AX.25" is the old - driver and still provided in case this driver does not work with - your serial interface chip. To configure the driver, use the sethdlc - utility available in the standard ax25 utilities package. - For more information on the modems, see - <file:Documentation/networking/device_drivers/hamradio/baycom.rst>. - - To compile this driver as a module, choose M here: the module - will be called baycom_ser_fdx. This is recommended. - -config BAYCOM_SER_HDX - tristate "BAYCOM ser12 halfduplex driver for AX.25" - depends on AX25 && HAS_IOPORT - select CRC_CCITT - help - This is one of two drivers for Baycom style simple amateur radio - modems that connect to a serial interface. The driver supports the - ser12 design in half-duplex mode. This is the old driver. It is - still provided in case your serial interface chip does not work with - the full-duplex driver. This driver is deprecated. To configure - the driver, use the sethdlc utility available in the standard ax25 - utilities package. For more information on the modems, see - <file:Documentation/networking/device_drivers/hamradio/baycom.rst>. - - To compile this driver as a module, choose M here: the module - will be called baycom_ser_hdx. This is recommended. - -config BAYCOM_PAR - tristate "BAYCOM picpar and par96 driver for AX.25" - depends on PARPORT && AX25 - select CRC_CCITT - help - This is a driver for Baycom style simple amateur radio modems that - connect to a parallel interface. The driver supports the picpar and - par96 designs. To configure the driver, use the sethdlc utility - available in the standard ax25 utilities package. - For more information on the modems, see - <file:Documentation/networking/device_drivers/hamradio/baycom.rst>. - - To compile this driver as a module, choose M here: the module - will be called baycom_par. This is recommended. - -config BAYCOM_EPP - tristate "BAYCOM epp driver for AX.25" - depends on PARPORT && AX25 && !64BIT - select CRC_CCITT - help - This is a driver for Baycom style simple amateur radio modems that - connect to a parallel interface. The driver supports the EPP - designs. To configure the driver, use the sethdlc utility available - in the standard ax25 utilities package. - For more information on the modems, see - <file:Documentation/networking/device_drivers/hamradio/baycom.rst>. - - To compile this driver as a module, choose M here: the module - will be called baycom_epp. This is recommended. - -config YAM - tristate "YAM driver for AX.25" - depends on AX25 && HAS_IOPORT - help - The YAM is a modem for packet radio which connects to the serial - port and includes some of the functions of a Terminal Node - Controller. If you have one of those, say Y here. - - To compile this driver as a module, choose M here: the module - will be called yam. - -net/Kconfig +0
-1@@ -414,7 +414,6 @@ endmenu # Network testing endmenu # Networking options -source "net/ax25/Kconfig" source "net/can/Kconfig" source "net/bluetooth/Kconfig" source "net/rxrpc/Kconfig"net/ax25/Kconfig deleted +0
-108@@ -1,108 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -# -# Amateur Radio protocols and AX.25 device configuration -# - -menuconfig HAMRADIO - depends on NET - bool "Amateur Radio support" - help - If you want to connect your Linux box to an amateur radio, answer Y - here. You want to read <https://www.tapr.org/> - and more specifically about AX.25 on Linux - <https://linux-ax25.in-berlin.de>. - - Note that the answer to this question won't directly affect the - kernel: saying N will just cause the configurator to skip all - the questions about amateur radio. - -comment "Packet Radio protocols" - depends on HAMRADIO - -config AX25 - tristate "Amateur Radio AX.25 Level 2 protocol" - depends on HAMRADIO - help - This is the protocol used for computer communication over amateur - radio. It is either used by itself for point-to-point links, or to - carry other protocols such as tcp/ip. To use it, you need a device - that connects your Linux box to your amateur radio. You can either - use a low speed TNC (a Terminal Node Controller acts as a kind of - modem connecting your computer's serial port to your radio's - microphone input and speaker output) supporting the KISS protocol or - one of the various SCC cards that are supported by the generic Z8530 - or the DMA SCC driver. Another option are the Baycom modem serial - and parallel port hacks or the sound card modem (supported by their - own drivers). If you say Y here, you also have to say Y to one of - those drivers. - - Information about where to get supporting software for Linux amateur - radio as well as information about how to configure an AX.25 port is - contained in the AX25-HOWTO, available from - <https://www.tldp.org/docs.html#howto>. You might also want to - check out the file <file:Documentation/networking/ax25.rst> in the - kernel source. More information about digital amateur radio in - general is on the WWW at - <https://www.tapr.org/>. - - To compile this driver as a module, choose M here: the - module will be called ax25. - -config AX25_DAMA_SLAVE - bool "AX.25 DAMA Slave support" - default y - depends on AX25 - help - DAMA is a mechanism to prevent collisions when doing AX.25 - networking. A DAMA server (called "master") accepts incoming traffic - from clients (called "slaves") and redistributes it to other slaves. - If you say Y here, your Linux box will act as a DAMA slave; this is - transparent in that you don't have to do any special DAMA - configuration. Linux cannot yet act as a DAMA server. This option - only compiles DAMA slave support into the kernel. It still needs to - be enabled at runtime. For more about DAMA see - <https://linux-ax25.in-berlin.de>. If unsure, say Y. - -config NETROM - tristate "Amateur Radio NET/ROM protocol" - depends on AX25 - help - NET/ROM is a network layer protocol on top of AX.25 useful for - routing. - - A comprehensive listing of all the software for Linux amateur radio - users as well as information about how to configure an AX.25 port is - contained in the Linux Ham Wiki, available from - <https://linux-ax25.in-berlin.de>. You also might want to check out - the file <file:Documentation/networking/ax25.rst>. More information - about digital amateur radio in general is on the WWW at - <https://www.tapr.org/>. - - To compile this driver as a module, choose M here: the - module will be called netrom. - -config ROSE - tristate "Amateur Radio X.25 PLP (Rose)" - depends on AX25 - help - The Packet Layer Protocol (PLP) is a way to route packets over X.25 - connections in general and amateur radio AX.25 connections in - particular, essentially an alternative to NET/ROM. - - A comprehensive listing of all the software for Linux amateur radio - users as well as information about how to configure an AX.25 port is - contained in the Linux Ham Wiki, available from - <https://linux-ax25.in-berlin.de>. You also might want to check out - the file <file:Documentation/networking/ax25.rst>. More information - about digital amateur radio in general is on the WWW at - <https://www.tapr.org/>. - - To compile this driver as a module, choose M here: the - module will be called rose. - -menu "AX.25 network device drivers" - depends on HAMRADIO && AX25 - -source "drivers/net/hamradio/Kconfig" - -endmenudrivers/net/Makefile +0
-1@@ -54,7 +54,6 @@ obj-y += dsa/ endif obj-$(CONFIG_ETHERNET) += ethernet/ obj-$(CONFIG_FDDI) += fddi/ -obj-$(CONFIG_HAMRADIO) += hamradio/ obj-$(CONFIG_QCOM_IPA) += ipa/ obj-$(CONFIG_PLIP) += plip/ obj-$(CONFIG_PPP) += ppp/drivers/net/hamradio/Makefile deleted +0
-22@@ -1,22 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -# -# Makefile for the Linux AX.25 and HFMODEM device drivers. -# -# -# 19971130 Moved the amateur radio related network drivers from -# drivers/net/ to drivers/hamradio for easier maintenance. -# Joerg Reuter DL1BKE <[email protected]> -# -# 20000806 Rewritten to use lists instead of if-statements. -# Christoph Hellwig <[email protected]> -# - -obj-$(CONFIG_SCC) += scc.o -obj-$(CONFIG_MKISS) += mkiss.o -obj-$(CONFIG_6PACK) += 6pack.o -obj-$(CONFIG_YAM) += yam.o -obj-$(CONFIG_BPQETHER) += bpqether.o -obj-$(CONFIG_BAYCOM_SER_FDX) += baycom_ser_fdx.o hdlcdrv.o -obj-$(CONFIG_BAYCOM_SER_HDX) += baycom_ser_hdx.o hdlcdrv.o -obj-$(CONFIG_BAYCOM_PAR) += baycom_par.o hdlcdrv.o -obj-$(CONFIG_BAYCOM_EPP) += baycom_epp.o hdlcdrv.onet/Makefile +0
-3@@ -28,9 +28,6 @@ obj-y += dsa/ obj-$(CONFIG_ATALK) += appletalk/ obj-$(CONFIG_X25) += x25/ obj-$(CONFIG_LAPB) += lapb/ -obj-$(CONFIG_NETROM) += netrom/ -obj-$(CONFIG_ROSE) += rose/ -obj-$(CONFIG_AX25) += ax25/ obj-$(CONFIG_CAN) += can/ obj-$(CONFIG_BT) += bluetooth/ obj-$(CONFIG_SUNRPC) += sunrpc/net/ax25/Makefile deleted +0
-12@@ -1,12 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -# -# Makefile for the Linux AX.25 layer. -# - -obj-$(CONFIG_AX25) += ax25.o - -ax25-y := ax25_addr.o ax25_dev.o ax25_iface.o ax25_in.o ax25_ip.o ax25_out.o \ - ax25_route.o ax25_std_in.o ax25_std_subr.o ax25_std_timer.o \ - ax25_subr.o ax25_timer.o ax25_uid.o af_ax25.o -ax25-$(CONFIG_AX25_DAMA_SLAVE) += ax25_ds_in.o ax25_ds_subr.o ax25_ds_timer.o -ax25-$(CONFIG_SYSCTL) += sysctl_net_ax25.onet/netrom/Makefile deleted +0
-10@@ -1,10 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -# -# Makefile for the Linux NET/ROM layer. -# - -obj-$(CONFIG_NETROM) += netrom.o - -netrom-y := af_netrom.o nr_dev.o nr_in.o nr_loopback.o \ - nr_out.o nr_route.o nr_subr.o nr_timer.o -netrom-$(CONFIG_SYSCTL) += sysctl_net_netrom.onet/rose/Makefile deleted +0
-10@@ -1,10 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -# -# Makefile for the Linux Rose (X.25 PLP) layer. -# - -obj-$(CONFIG_ROSE) += rose.o - -rose-y := af_rose.o rose_dev.o rose_in.o rose_link.o rose_loopback.o \ - rose_out.o rose_route.o rose_subr.o rose_timer.o -rose-$(CONFIG_SYSCTL) += sysctl_net_rose.odrivers/net/hamradio/z8530.h deleted +0
-246@@ -1,246 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ - -/* 8530 Serial Communications Controller Register definitions */ -#define FLAG 0x7e - -/* Write Register 0 */ -#define R0 0/* Register selects */ -#define R1 1 -#define R2 2 -#define R3 3 -#define R4 4 -#define R5 5 -#define R6 6 -#define R7 7 -#define R8 8 -#define R9 9 -#define R10 10 -#define R11 11 -#define R12 12 -#define R13 13 -#define R14 14 -#define R15 15 - -#define NULLCODE 0/* Null Code */ -#define POINT_HIGH 0x8/* Select upper half of registers */ -#define RES_EXT_INT 0x10/* Reset Ext. Status Interrupts */ -#define SEND_ABORT 0x18/* HDLC Abort */ -#define RES_RxINT_FC 0x20/* Reset RxINT on First Character */ -#define RES_Tx_P 0x28/* Reset TxINT Pending */ -#define ERR_RES 0x30/* Error Reset */ -#define RES_H_IUS 0x38/* Reset highest IUS */ - -#define RES_Rx_CRC 0x40/* Reset Rx CRC Checker */ -#define RES_Tx_CRC 0x80/* Reset Tx CRC Checker */ -#define RES_EOM_L 0xC0/* Reset EOM latch */ - -/* Write Register 1 */ - -#define EXT_INT_ENAB 0x1/* Ext Int Enable */ -#define TxINT_ENAB 0x2/* Tx Int Enable */ -#define PAR_SPEC 0x4/* Parity is special condition */ - -#define RxINT_DISAB 0/* Rx Int Disable */ -#define RxINT_FCERR 0x8/* Rx Int on First Character Only or Error */ -#define INT_ALL_Rx 0x10/* Int on all Rx Characters or error */ -#define INT_ERR_Rx 0x18/* Int on error only */ - -#define WT_RDY_RT 0x20/* Wait/Ready on R/T */ -#define WT_FN_RDYFN 0x40/* Wait/FN/Ready FN */ -#define WT_RDY_ENAB 0x80/* Wait/Ready Enable */ - -/* Write Register #2 (Interrupt Vector) */ - -/* Write Register 3 */ - -#define RxENABLE 0x1/* Rx Enable */ -#define SYNC_L_INH 0x2/* Sync Character Load Inhibit */ -#define ADD_SM 0x4/* Address Search Mode (SDLC) */ -#define RxCRC_ENAB 0x8/* Rx CRC Enable */ -#define ENT_HM 0x10/* Enter Hunt Mode */ -#define AUTO_ENAB 0x20/* Auto Enables */ -#define Rx5 0x0/* Rx 5 Bits/Character */ -#define Rx7 0x40/* Rx 7 Bits/Character */ -#define Rx6 0x80/* Rx 6 Bits/Character */ -#define Rx8 0xc0/* Rx 8 Bits/Character */ - -/* Write Register 4 */ - -#define PAR_ENA 0x1/* Parity Enable */ -#define PAR_EVEN 0x2/* Parity Even/Odd* */ - -#define SYNC_ENAB 0/* Sync Modes Enable */ -#define SB1 0x4/* 1 stop bit/char */ -#define SB15 0x8/* 1.5 stop bits/char */ -#define SB2 0xc/* 2 stop bits/char */ - -#define MONSYNC 0/* 8 Bit Sync character */ -#define BISYNC 0x10/* 16 bit sync character */ -#define SDLC 0x20/* SDLC Mode (01111110 Sync Flag) */ -#define EXTSYNC 0x30/* External Sync Mode */ - -#define X1CLK 0x0/* x1 clock mode */ -#define X16CLK 0x40/* x16 clock mode */ -#define X32CLK 0x80/* x32 clock mode */ -#define X64CLK 0xC0/* x64 clock mode */ - -/* Write Register 5 */ - -#define TxCRC_ENAB 0x1/* Tx CRC Enable */ -#define RTS 0x2/* RTS */ -#define SDLC_CRC 0x4/* SDLC/CRC-16 */ -#define TxENAB 0x8/* Tx Enable */ -#define SND_BRK 0x10/* Send Break */ -#define Tx5 0x0/* Tx 5 bits (or less)/character */ -#define Tx7 0x20/* Tx 7 bits/character */ -#define Tx6 0x40/* Tx 6 bits/character */ -#define Tx8 0x60/* Tx 8 bits/character */ -#define DTR 0x80/* DTR */ - -/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */ - -/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */ - -/* Write Register 8 (transmit buffer) */ - -/* Write Register 9 (Master interrupt control) */ -#define VIS 1/* Vector Includes Status */ -#define NV 2/* No Vector */ -#define DLC 4/* Disable Lower Chain */ -#define MIE 8/* Master Interrupt Enable */ -#define STATHI 0x10/* Status high */ -#define NORESET 0/* No reset on write to R9 */ -#define CHRB 0x40/* Reset channel B */ -#define CHRA 0x80/* Reset channel A */ -#define FHWRES 0xc0/* Force hardware reset */ - -/* Write Register 10 (misc control bits) */ -#define BIT6 1/* 6 bit/8bit sync */ -#define LOOPMODE 2/* SDLC Loop mode */ -#define ABUNDER 4/* Abort/flag on SDLC xmit underrun */ -#define MARKIDLE 8/* Mark/flag on idle */ -#define GAOP 0x10/* Go active on poll */ -#define NRZ 0/* NRZ mode */ -#define NRZI 0x20/* NRZI mode */ -#define FM1 0x40/* FM1 (transition = 1) */ -#define FM0 0x60/* FM0 (transition = 0) */ -#define CRCPS 0x80/* CRC Preset I/O */ - -/* Write Register 11 (Clock Mode control) */ -#define TRxCXT 0/* TRxC = Xtal output */ -#define TRxCTC 1/* TRxC = Transmit clock */ -#define TRxCBR 2/* TRxC = BR Generator Output */ -#define TRxCDP 3/* TRxC = DPLL output */ -#define TRxCOI 4/* TRxC O/I */ -#define TCRTxCP 0/* Transmit clock = RTxC pin */ -#define TCTRxCP 8/* Transmit clock = TRxC pin */ -#define TCBR 0x10/* Transmit clock = BR Generator output */ -#define TCDPLL 0x18/* Transmit clock = DPLL output */ -#define RCRTxCP 0/* Receive clock = RTxC pin */ -#define RCTRxCP 0x20/* Receive clock = TRxC pin */ -#define RCBR 0x40/* Receive clock = BR Generator output */ -#define RCDPLL 0x60/* Receive clock = DPLL output */ -#define RTxCX 0x80/* RTxC Xtal/No Xtal */ - -/* Write Register 12 (lower byte of baud rate generator time constant) */ - -/* Write Register 13 (upper byte of baud rate generator time constant) */ - -/* Write Register 14 (Misc control bits) */ -#define BRENABL 1/* Baud rate generator enable */ -#define BRSRC 2/* Baud rate generator source */ -#define DTRREQ 4/* DTR/Request function */ -#define AUTOECHO 8/* Auto Echo */ -#define LOOPBAK 0x10/* Local loopback */ -#define SEARCH 0x20/* Enter search mode */ -#define RMC 0x40/* Reset missing clock */ -#define DISDPLL 0x60/* Disable DPLL */ -#define SSBR 0x80/* Set DPLL source = BR generator */ -#define SSRTxC 0xa0/* Set DPLL source = RTxC */ -#define SFMM 0xc0/* Set FM mode */ -#define SNRZI 0xe0/* Set NRZI mode */ - -/* Write Register 15 (external/status interrupt control) */ -#define ZCIE 2/* Zero count IE */ -#define DCDIE 8/* DCD IE */ -#define SYNCIE 0x10/* Sync/hunt IE */ -#define CTSIE 0x20/* CTS IE */ -#define TxUIE 0x40/* Tx Underrun/EOM IE */ -#define BRKIE 0x80/* Break/Abort IE */ - - -/* Read Register 0 */ -#define Rx_CH_AV 0x1/* Rx Character Available */ -#define ZCOUNT 0x2/* Zero count */ -#define Tx_BUF_EMP 0x4/* Tx Buffer empty */ -#define DCD 0x8/* DCD */ -#define SYNC_HUNT 0x10/* Sync/hunt */ -#define CTS 0x20/* CTS */ -#define TxEOM 0x40/* Tx underrun */ -#define BRK_ABRT 0x80/* Break/Abort */ - -/* Read Register 1 */ -#define ALL_SNT 0x1/* All sent */ -/* Residue Data for 8 Rx bits/char programmed */ -#define RES3 0x8/* 0/3 */ -#define RES4 0x4/* 0/4 */ -#define RES5 0xc/* 0/5 */ -#define RES6 0x2/* 0/6 */ -#define RES7 0xa/* 0/7 */ -#define RES8 0x6/* 0/8 */ -#define RES18 0xe/* 1/8 */ -#define RES28 0x0/* 2/8 */ -/* Special Rx Condition Interrupts */ -#define PAR_ERR 0x10/* Parity error */ -#define Rx_OVR 0x20/* Rx Overrun Error */ -#define CRC_ERR 0x40/* CRC/Framing Error */ -#define END_FR 0x80/* End of Frame (SDLC) */ - -/* Read Register 2 (channel b only) - Interrupt vector */ - -/* Read Register 3 (interrupt pending register) ch a only */ -#define CHBEXT 0x1/* Channel B Ext/Stat IP */ -#define CHBTxIP 0x2/* Channel B Tx IP */ -#define CHBRxIP 0x4/* Channel B Rx IP */ -#define CHAEXT 0x8/* Channel A Ext/Stat IP */ -#define CHATxIP 0x10/* Channel A Tx IP */ -#define CHARxIP 0x20/* Channel A Rx IP */ - -/* Read Register 8 (receive data register) */ - -/* Read Register 10 (misc status bits) */ -#define ONLOOP 2/* On loop */ -#define LOOPSEND 0x10/* Loop sending */ -#define CLK2MIS 0x40/* Two clocks missing */ -#define CLK1MIS 0x80/* One clock missing */ - -/* Read Register 12 (lower byte of baud rate generator constant) */ - -/* Read Register 13 (upper byte of baud rate generator constant) */ - -/* Read Register 15 (value of WR 15) */ - -/* Z85C30/Z85230 Enhanced SCC register definitions */ - -/* Write Register 7' (SDLC/HDLC Programmable Enhancements) */ -#define AUTOTXF 0x01/* Auto Tx Flag */ -#define AUTOEOM 0x02/* Auto EOM Latch Reset */ -#define AUTORTS 0x04/* Auto RTS */ -#define TXDNRZI 0x08/* TxD Pulled High in SDLC NRZI mode */ -#define RXFIFOH 0x08/* Z85230: Int on RX FIFO half full */ -#define FASTDTR 0x10/* Fast DTR/REQ Mode */ -#define CRCCBCR 0x20/* CRC Check Bytes Completely Received */ -#define TXFIFOE 0x20/* Z85230: Int on TX FIFO completely empty */ -#define EXTRDEN 0x40/* Extended Read Enabled */ - -/* Write Register 15 (external/status interrupt control) */ -#define SHDLCE 1/* SDLC/HDLC Enhancements Enable */ -#define FIFOE 4/* FIFO Enable */ - -/* Read Register 6 (frame status FIFO) */ -#define BCLSB 0xff/* LSB of 14 bits count */ - -/* Read Register 7 (frame status FIFO) */ -#define BCMSB 0x3f/* MSB of 14 bits count */ -#define FDA 0x40/* FIFO Data Available Status */ -#define FOS 0x80/* FIFO Overflow Status */ include/linux/hdlcdrv.h deleted +0
-276@@ -1,276 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* -* hdlcdrv.h -- HDLC packet radio network driver. -* The Linux soundcard driver for 1200 baud and 9600 baud packet radio -* (C) 1996-1998 by Thomas Sailer, HB9JNX/AE4WA -*/ -#ifndef _HDLCDRV_H -#define _HDLCDRV_H - - -#include <linux/netdevice.h> -#include <linux/if.h> -#include <linux/spinlock.h> -#include <uapi/linux/hdlcdrv.h> - -#define HDLCDRV_MAGIC 0x5ac6e778 -#define HDLCDRV_HDLCBUFFER 32/* should be a power of 2 for speed reasons */ -#define HDLCDRV_BITBUFFER 256/* should be a power of 2 for speed reasons */ -#undef HDLCDRV_LOOPBACK/* define for HDLC debugging purposes */ -#define HDLCDRV_DEBUG - -/* maximum packet length, excluding CRC */ -#define HDLCDRV_MAXFLEN 400 - - -struct hdlcdrv_hdlcbuffer { -spinlock_t lock; -unsigned rd, wr; -unsigned short buf[HDLCDRV_HDLCBUFFER ]; -}; - -#ifdef HDLCDRV_DEBUG -struct hdlcdrv_bitbuffer { -unsigned int rd; -unsigned int wr; -unsigned int shreg; -unsigned char buffer[HDLCDRV_BITBUFFER ]; -}; - -static inline void hdlcdrv_add_bitbuffer (struct hdlcdrv_bitbuffer *buf, -unsigned int bit) -{ -unsigned char new; - - new = buf->shreg &1 ; - buf->shreg >>=1 ; - buf->shreg |= (!!bit) <<7 ; -if (new) { - buf->buffer[buf->wr] = buf->shreg; - buf->wr = (buf->wr+1 ) %sizeof (buf->buffer); - buf->shreg =0x80 ; - } -} - -static inline void hdlcdrv_add_bitbuffer_word (struct hdlcdrv_bitbuffer *buf, -unsigned int bits) -{ - buf->buffer[buf->wr] = bits &0xff ; - buf->wr = (buf->wr+1 ) %sizeof (buf->buffer); - buf->buffer[buf->wr] = (bits >>8 ) &0xff ; - buf->wr = (buf->wr+1 ) %sizeof (buf->buffer); - -} -#endif /* HDLCDRV_DEBUG */ - -/* -------------------------------------------------------------------- */ -/* -* Information that need to be kept for each driver. -*/ - -struct hdlcdrv_ops { -/* -* first some informations needed by the hdlcdrv routines -*/ -const char *drvname; -const char *drvinfo; -/* -* the routines called by the hdlcdrv routines -*/ -int (*open)(struct net_device *); -int (*close)(struct net_device *); -int (*ioctl)(struct net_device *,void __user *, -struct hdlcdrv_ioctl *,int ); -}; - -struct hdlcdrv_state { -int magic; -int opened; - -const struct hdlcdrv_ops *ops; - -struct { -int bitrate; - } par; - -struct hdlcdrv_pttoutput { -int dma2; -int seriobase; -int pariobase; -int midiiobase; -unsigned int flags; - } ptt_out; - -struct hdlcdrv_channel_params ch_params; - -struct hdlcdrv_hdlcrx { -struct hdlcdrv_hdlcbuffer hbuf; -unsigned long in_hdlc_rx; -/* 0 = sync hunt, != 0 receiving */ -int rx_state; -unsigned int bitstream; -unsigned int bitbuf; -int numbits; -unsigned char dcd; - -int len; -unsigned char *bp; -unsigned char buffer[HDLCDRV_MAXFLEN +2 ]; - } hdlcrx; - -struct hdlcdrv_hdlctx { -struct hdlcdrv_hdlcbuffer hbuf; -unsigned long in_hdlc_tx; -/* -* 0 = send flags -* 1 = send txtail (flags) -* 2 = send packet -*/ -int tx_state; -int numflags; -unsigned int bitstream; -unsigned char ptt; -int calibrate; -int slotcnt; - -unsigned int bitbuf; -int numbits; - -int len; -unsigned char *bp; -unsigned char buffer[HDLCDRV_MAXFLEN +2 ]; - } hdlctx; - -#ifdef HDLCDRV_DEBUG -struct hdlcdrv_bitbuffer bitbuf_channel; -struct hdlcdrv_bitbuffer bitbuf_hdlc; -#endif /* HDLCDRV_DEBUG */ - -int ptt_keyed; - -/* queued skb for transmission */ -struct sk_buff *skb; -}; - - -/* -------------------------------------------------------------------- */ - -static inline int hdlcdrv_hbuf_full (struct hdlcdrv_hdlcbuffer *hb) -{ -unsigned long flags; -int ret; - -spin_lock_irqsave (&hb->lock, flags); - ret = !((HDLCDRV_HDLCBUFFER -1 + hb->rd - hb->wr) %HDLCDRV_HDLCBUFFER ); -spin_unlock_irqrestore (&hb->lock, flags); -return ret; -} - -/* -------------------------------------------------------------------- */ - -static inline int hdlcdrv_hbuf_empty (struct hdlcdrv_hdlcbuffer *hb) -{ -unsigned long flags; -int ret; - -spin_lock_irqsave (&hb->lock, flags); - ret = (hb->rd == hb->wr); -spin_unlock_irqrestore (&hb->lock, flags); -return ret; -} - -/* -------------------------------------------------------------------- */ - -static inline unsigned short hdlcdrv_hbuf_get (struct hdlcdrv_hdlcbuffer *hb) -{ -unsigned long flags; -unsigned short val; -unsigned newr; - -spin_lock_irqsave (&hb->lock, flags); -if (hb->rd == hb->wr) - val =0 ; -else { - newr = (hb->rd+1 ) %HDLCDRV_HDLCBUFFER ; - val = hb->buf[hb->rd]; - hb->rd = newr; - } -spin_unlock_irqrestore (&hb->lock, flags); -return val; -} - -/* -------------------------------------------------------------------- */ - -static inline void hdlcdrv_hbuf_put (struct hdlcdrv_hdlcbuffer *hb, -unsigned short val) -{ -unsigned newp; -unsigned long flags; - -spin_lock_irqsave (&hb->lock, flags); - newp = (hb->wr+1 ) %HDLCDRV_HDLCBUFFER ; -if (newp != hb->rd) { - hb->buf[hb->wr] = val &0xffff ; - hb->wr = newp; - } -spin_unlock_irqrestore (&hb->lock, flags); -} - -/* -------------------------------------------------------------------- */ - -static inline void hdlcdrv_putbits (struct hdlcdrv_state *s,unsigned int bits) -{ -hdlcdrv_hbuf_put (&s->hdlcrx.hbuf, bits); -} - -static inline unsigned int hdlcdrv_getbits (struct hdlcdrv_state *s) -{ -unsigned int ret; - -if (hdlcdrv_hbuf_empty (&s->hdlctx.hbuf)) { -if (s->hdlctx.calibrate >0 ) - s->hdlctx.calibrate--; -else - s->hdlctx.ptt =0 ; - ret =0 ; - }else - ret =hdlcdrv_hbuf_get (&s->hdlctx.hbuf); -#ifdef HDLCDRV_LOOPBACK -hdlcdrv_hbuf_put (&s->hdlcrx.hbuf, ret); -#endif /* HDLCDRV_LOOPBACK */ -return ret; -} - -static inline void hdlcdrv_channelbit (struct hdlcdrv_state *s,unsigned int bit) -{ -#ifdef HDLCDRV_DEBUG -hdlcdrv_add_bitbuffer (&s->bitbuf_channel, bit); -#endif /* HDLCDRV_DEBUG */ -} - -static inline void hdlcdrv_setdcd (struct hdlcdrv_state *s,int dcd) -{ - s->hdlcrx.dcd = !!dcd; -} - -static inline int hdlcdrv_ptt (struct hdlcdrv_state *s) -{ -return s->hdlctx.ptt || (s->hdlctx.calibrate >0 ); -} - -/* -------------------------------------------------------------------- */ - -void hdlcdrv_receiver (struct net_device *,struct hdlcdrv_state *); -void hdlcdrv_transmitter (struct net_device *,struct hdlcdrv_state *); -void hdlcdrv_arbitrate (struct net_device *,struct hdlcdrv_state *); -struct net_device *hdlcdrv_register (const struct hdlcdrv_ops *ops, -unsigned int privsize,const char *ifname, -unsigned int baseaddr,unsigned int irq, -unsigned int dma); -void hdlcdrv_unregister (struct net_device *dev); - -/* -------------------------------------------------------------------- */ - - - -#endif /* _HDLCDRV_H */ include/linux/netdevice.h +1
-4@@ -162,7 +162,7 @@ static inline bool dev_xmit_complete(int rc)#if defined(CONFIG_HYPERV_NET )# define LL_MAX_HEADER 128 -#elif defined(CONFIG_WLAN ) ||IS_ENABLED (CONFIG_AX25 ) +#elif defined(CONFIG_WLAN )# if defined(CONFIG_MAC80211_MESH )# define LL_MAX_HEADER 128# else @@ -2316,9 +2316,6 @@ struct net_device {#if IS_ENABLED (CONFIG_ATALK )void *atalk_ptr;#endif -#if IS_ENABLED (CONFIG_AX25 ) -struct ax25_dev __rcu *ax25_ptr; -#endif #if IS_ENABLED (CONFIG_CFG80211 )struct wireless_dev *ieee80211_ptr;#endif include/linux/scc.h deleted +0
-86@@ -1,86 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* $Id: scc.h,v 1.29 1997/04/02 14:56:45 jreuter Exp jreuter $ */ -#ifndef _SCC_H -#define _SCC_H - -#include <uapi/linux/scc.h> - - -enum {TX_OFF ,TX_ON };/* command for scc_key_trx() */ - -/* Vector masks in RR2B */ - -#define VECTOR_MASK 0x06 -#define TXINT 0x00 -#define EXINT 0x02 -#define RXINT 0x04 -#define SPINT 0x06 - -#ifdef CONFIG_SCC_DELAY -#define Inb (port) inb_p(port) -#define Outb (port, val) outb_p(val, port) -#else -#define Inb (port) inb(port) -#define Outb (port, val) outb(val, port) -#endif - -/* SCC channel control structure for KISS */ - -struct scc_kiss { -unsigned char txdelay;/* Transmit Delay 10 ms/cnt */ -unsigned char persist;/* Persistence (0-255) as a % */ -unsigned char slottime;/* Delay to wait on persistence hit */ -unsigned char tailtime;/* Delay after last byte written */ -unsigned char fulldup;/* Full Duplex mode 0=CSMA 1=DUP 2=ALWAYS KEYED */ -unsigned char waittime;/* Waittime before any transmit attempt */ -unsigned int maxkeyup;/* Maximum time to transmit (seconds) */ -unsigned int mintime;/* Minimal offtime after MAXKEYUP timeout (seconds) */ -unsigned int idletime;/* Maximum idle time in ALWAYS KEYED mode (seconds) */ -unsigned int maxdefer;/* Timer for CSMA channel busy limit */ -unsigned char tx_inhibit;/* Transmit is not allowed when set */ -unsigned char group;/* Group ID for AX.25 TX interlocking */ -unsigned char mode;/* 'normal' or 'hwctrl' mode (unused) */ -unsigned char softdcd;/* Use DPLL instead of DCD pin for carrier detect */ -}; - - -/* SCC channel structure */ - -struct scc_channel { -int init;/* channel exists? */ - -struct net_device *dev;/* link to device control structure */ -struct net_device_stats dev_stat;/* device statistics */ - -char brand;/* manufacturer of the board */ -long clock;/* used clock */ - -io_port ctrl;/* I/O address of CONTROL register */ -io_port data;/* I/O address of DATA register */ -io_port special;/* I/O address of special function port */ -int irq;/* Number of Interrupt */ - -char option; -char enhanced;/* Enhanced SCC support */ - -unsigned char wreg[16 ];/* Copy of last written value in WRx */ -unsigned char status;/* Copy of R0 at last external interrupt */ -unsigned char dcd;/* DCD status */ - -struct scc_kiss kiss;/* control structure for KISS params */ -struct scc_stat stat;/* statistical information */ -struct scc_modem modem;/* modem information */ - -struct sk_buff_head tx_queue;/* next tx buffer */ -struct sk_buff *rx_buff;/* pointer to frame currently received */ -struct sk_buff *tx_buff;/* pointer to frame currently transmitted */ - -/* Timer */ -struct timer_list tx_t;/* tx timer for this channel */ -struct timer_list tx_wdog;/* tx watchdogs */ - -/* Channel lock */ -spinlock_t lock;/* Channel guard lock */ -}; - -#endif /* defined(_SCC_H) */ include/linux/yam.h deleted +0
-67@@ -1,67 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0-or-later */ -/*****************************************************************************/ - -/* -* yam.h -- YAM radio modem driver. -* -* Copyright (C) 1998 Frederic Rible F1OAT ([email protected]) -* Adapted from baycom.c driver written by Thomas Sailer ([email protected]) -* -* Please note that the GPL allows you to use the driver, NOT the radio. -* In order to use the radio, you need a license from the communications -* authority of your country. -*/ - -/*****************************************************************************/ - -#define SIOCYAMRESERVED (0) -#define SIOCYAMSCFG (1)/* Set configuration */ -#define SIOCYAMGCFG (2)/* Get configuration */ -#define SIOCYAMSMCS (3)/* Set mcs data */ - -#define YAM_IOBASE (1 << 0) -#define YAM_IRQ (1 << 1) -#define YAM_BITRATE (1 << 2)/* Bit rate of radio port ->57600 */ -#define YAM_MODE (1 << 3)/* 0=simplex 1=duplex 2=duplex+tempo */ -#define YAM_HOLDDLY (1 << 4)/* duplex tempo (sec) */ -#define YAM_TXDELAY (1 << 5)/* Tx Delay (ms) */ -#define YAM_TXTAIL (1 << 6)/* Tx Tail (ms) */ -#define YAM_PERSIST (1 << 7)/* Persist (ms) */ -#define YAM_SLOTTIME (1 << 8)/* Slottime (ms) */ -#define YAM_BAUDRATE (1 << 9)/* Baud rate of rs232 port ->115200 */ - -#define YAM_MAXBITRATE 57600 -#define YAM_MAXBAUDRATE 115200 -#define YAM_MAXMODE 2 -#define YAM_MAXHOLDDLY 99 -#define YAM_MAXTXDELAY 999 -#define YAM_MAXTXTAIL 999 -#define YAM_MAXPERSIST 255 -#define YAM_MAXSLOTTIME 999 - -#define YAM_FPGA_SIZE 5302 - -struct yamcfg { -unsigned int mask;/* Mask of commands */ -unsigned int iobase;/* IO Base of COM port */ -unsigned int irq;/* IRQ of COM port */ -unsigned int bitrate;/* Bit rate of radio port */ -unsigned int baudrate;/* Baud rate of the RS232 port */ -unsigned int txdelay;/* TxDelay */ -unsigned int txtail;/* TxTail */ -unsigned int persist;/* Persistence */ -unsigned int slottime;/* Slottime */ -unsigned int mode;/* mode 0 (simp), 1(Dupl), 2(Dupl+delay) */ -unsigned int holddly;/* PTT delay in FullDuplex 2 mode */ -}; - -struct yamdrv_ioctl_cfg { -int cmd; -struct yamcfg cfg; -}; - -struct yamdrv_ioctl_mcs { -int cmd; -unsigned int bitrate; -unsigned char bits[YAM_FPGA_SIZE ]; -};include/net/ax25.h +3
-473@@ -1,480 +1,10 @@/* SPDX-License-Identifier: GPL-2.0 */ -/* -* Declarations of AX.25 type objects. -* -* Alan Cox (GW4PTS) 10/11/93 -*/ #ifndef _AX25_H -#define _AX25_H +#define _AX25_H#include <linux/ax25.h> -#include <linux/spinlock.h> -#include <linux/timer.h> -#include <linux/list.h> -#include <linux/slab.h> -#include <linux/refcount.h> -#include <net/neighbour.h> -#include <net/sock.h> -#include <linux/seq_file.h> -#define AX25_T1CLAMPLO 1 -#define AX25_T1CLAMPHI (30 * HZ) - -#define AX25_BPQ_HEADER_LEN 16 -#define AX25_KISS_HEADER_LEN 1 - -#define AX25_HEADER_LEN 17 -#define AX25_ADDR_LEN 7 -#define AX25_DIGI_HEADER_LEN (AX25_MAX_DIGIS * AX25_ADDR_LEN) -#define AX25_MAX_HEADER_LEN (AX25_HEADER_LEN + AX25_DIGI_HEADER_LEN) - -/* AX.25 Protocol IDs */ -#define AX25_P_ROSE 0x01 -#define AX25_P_VJCOMP 0x06/* Compressed TCP/IP packet */ -/* Van Jacobsen (RFC 1144) */ -#define AX25_P_VJUNCOMP 0x07/* Uncompressed TCP/IP packet */ -/* Van Jacobsen (RFC 1144) */ -#define AX25_P_SEGMENT 0x08/* Segmentation fragment */ -#define AX25_P_TEXNET 0xc3/* TEXTNET datagram protocol */ -#define AX25_P_LQ 0xc4/* Link Quality Protocol */ -#define AX25_P_ATALK 0xca/* Appletalk */ -#define AX25_P_ATALK_ARP 0xcb/* Appletalk ARP */ -#define AX25_P_IP 0xcc/* ARPA Internet Protocol */ -#define AX25_P_ARP 0xcd/* ARPA Address Resolution */ -#define AX25_P_FLEXNET 0xce/* FlexNet */ -#define AX25_P_NETROM 0xcf/* NET/ROM */ -#define AX25_P_TEXT 0xF0/* No layer 3 protocol impl. */ - -/* AX.25 Segment control values */ -#define AX25_SEG_REM 0x7F -#define AX25_SEG_FIRST 0x80 - -#define AX25_CBIT 0x80/* Command/Response bit */ -#define AX25_EBIT 0x01/* HDLC Address Extension bit */ -#define AX25_HBIT 0x80/* Has been repeated bit */ - -#define AX25_SSSID_SPARE 0x60/* Unused bits in SSID for standard AX.25 */ -#define AX25_ESSID_SPARE 0x20/* Unused bits in SSID for extended AX.25 */ -#define AX25_DAMA_FLAG 0x20/* Well, it is *NOT* unused! (dl1bke 951121 */ - -#define AX25_COND_ACK_PENDING 0x01 -#define AX25_COND_REJECT 0x02 -#define AX25_COND_PEER_RX_BUSY 0x04 -#define AX25_COND_OWN_RX_BUSY 0x08 -#define AX25_COND_DAMA_MODE 0x10 - -#ifndef _LINUX_NETDEVICE_H -#include <linux/netdevice.h> -#endif - -/* Upper sub-layer (LAPB) definitions */ - -/* Control field templates */ -#define AX25_I 0x00/* Information frames */ -#define AX25_S 0x01/* Supervisory frames */ -#define AX25_RR 0x01/* Receiver ready */ -#define AX25_RNR 0x05/* Receiver not ready */ -#define AX25_REJ 0x09/* Reject */ -#define AX25_U 0x03/* Unnumbered frames */ -#define AX25_SABM 0x2f/* Set Asynchronous Balanced Mode */ -#define AX25_SABME 0x6f/* Set Asynchronous Balanced Mode Extended */ -#define AX25_DISC 0x43/* Disconnect */ -#define AX25_DM 0x0f/* Disconnected mode */ -#define AX25_UA 0x63/* Unnumbered acknowledge */ -#define AX25_FRMR 0x87/* Frame reject */ -#define AX25_UI 0x03/* Unnumbered information */ -#define AX25_XID 0xaf/* Exchange information */ -#define AX25_TEST 0xe3/* Test */ - -#define AX25_PF 0x10/* Poll/final bit for standard AX.25 */ -#define AX25_EPF 0x01/* Poll/final bit for extended AX.25 */ - -#define AX25_ILLEGAL 0x100/* Impossible to be a real frame type */ - -#define AX25_POLLOFF 0 -#define AX25_POLLON 1 - -/* AX25 L2 C-bit */ -#define AX25_COMMAND 1 -#define AX25_RESPONSE 2 - -/* Define Link State constants. */ - -enum { -AX25_STATE_0 ,/* Listening */ -AX25_STATE_1 ,/* SABM sent */ -AX25_STATE_2 ,/* DISC sent */ -AX25_STATE_3 ,/* Established */ -AX25_STATE_4 /* Recovery */ -}; - -#define AX25_MODULUS 8/* Standard AX.25 modulus */ -#define AX25_EMODULUS 128/* Extended AX.25 modulus */ - -enum { -AX25_PROTO_STD_SIMPLEX , -AX25_PROTO_STD_DUPLEX , -#ifdef CONFIG_AX25_DAMA_SLAVE -AX25_PROTO_DAMA_SLAVE , -#endif - __AX25_PROTO_MAX, -AX25_PROTO_MAX = __AX25_PROTO_MAX -1 -}; - -enum { -AX25_VALUES_IPDEFMODE ,/* 0=DG 1=VC */ -AX25_VALUES_AXDEFMODE ,/* 0=Normal 1=Extended Seq Nos */ -AX25_VALUES_BACKOFF ,/* 0=None 1=Linear 2=Exponential */ -AX25_VALUES_CONMODE ,/* Allow connected modes - 0=No 1=no "PID text" 2=all PIDs */ -AX25_VALUES_WINDOW ,/* Default window size for standard AX.25 */ -AX25_VALUES_EWINDOW ,/* Default window size for extended AX.25 */ -AX25_VALUES_T1 ,/* Default T1 timeout value */ -AX25_VALUES_T2 ,/* Default T2 timeout value */ -AX25_VALUES_T3 ,/* Default T3 timeout value */ -AX25_VALUES_IDLE ,/* Connected mode idle timer */ -AX25_VALUES_N2 ,/* Default N2 value */ -AX25_VALUES_PACLEN ,/* AX.25 MTU */ -AX25_VALUES_PROTOCOL ,/* Std AX.25, DAMA Slave */ -#ifdef CONFIG_AX25_DAMA_SLAVE -AX25_VALUES_DS_TIMEOUT ,/* DAMA Slave timeout */ -#endif -AX25_MAX_VALUES /* THIS MUST REMAIN THE LAST ENTRY OF THIS LIST */ -}; - -#define AX25_DEF_IPDEFMODE 0/* Datagram */ -#define AX25_DEF_AXDEFMODE 0/* Normal */ -#define AX25_DEF_BACKOFF 1/* Linear backoff */ -#define AX25_DEF_CONMODE 2/* Connected mode allowed */ -#define AX25_DEF_WINDOW 2/* Window=2 */ -#define AX25_DEF_EWINDOW 32/* Module-128 Window=32 */ -#define AX25_DEF_T1 10000/* T1=10s */ -#define AX25_DEF_T2 3000/* T2=3s */ -#define AX25_DEF_T3 300000/* T3=300s */ -#define AX25_DEF_N2 10/* N2=10 */ -#define AX25_DEF_IDLE 0/* Idle=None */ -#define AX25_DEF_PACLEN 256/* Paclen=256 */ -#define AX25_DEF_PROTOCOL AX25_PROTO_STD_SIMPLEX/* Standard AX.25 */ -#define AX25_DEF_DS_TIMEOUT 180000/* DAMA timeout 3 minutes */ - -typedef struct ax25_uid_assoc { -struct hlist_node uid_node; -refcount_t refcount; -kuid_t uid; -ax25_address call; -}ax25_uid_assoc ; - -#define ax25_uid_for_each (__ax25, list) \ - hlist_for_each_entry(__ax25, list, uid_node) - -#define ax25_uid_hold (ax25) \ - refcount_inc(&((ax25)->refcount)) - -static inline void ax25_uid_put (ax25_uid_assoc *assoc) -{ -if (refcount_dec_and_test (&assoc->refcount)) { -kfree (assoc); - } -} - -typedef struct { -ax25_address calls[AX25_MAX_DIGIS ]; -unsigned char repeated[AX25_MAX_DIGIS ]; -unsigned char ndigi; -signed char lastrepeat; -}ax25_digi ; - -typedef struct ax25_route { -struct ax25_route *next; -ax25_address callsign; -struct net_device *dev; -ax25_digi *digipeat; -char ip_mode; -}ax25_route ; - -void __ax25_put_route (ax25_route *ax25_rt); - -extern rwlock_t ax25_route_lock; - -static inline void ax25_route_lock_use (void ) -{ -read_lock (&ax25_route_lock); -} - -static inline void ax25_route_lock_unuse (void ) -{ -read_unlock (&ax25_route_lock); -} - -typedef struct { -char slave;/* slave_mode? */ -struct timer_list slave_timer;/* timeout timer */ -unsigned short slave_timeout;/* when? */ -}ax25_dama_info ; - -typedef struct ax25_dev { -struct list_head list; - -struct net_device *dev; -netdevice_tracker dev_tracker; - -struct net_device *forward; -struct ctl_table_header *sysheader; -int values[AX25_MAX_VALUES ]; -#ifdef CONFIG_AX25_DAMA_SLAVE -ax25_dama_info dama; -#endif -refcount_t refcount; -bool device_up; -struct rcu_head rcu; -}ax25_dev ; - -typedef struct ax25_cb { -struct hlist_node ax25_node; -ax25_address source_addr, dest_addr; -ax25_digi *digipeat; -ax25_dev *ax25_dev; -netdevice_tracker dev_tracker; -unsigned char iamdigi; -unsigned char state, modulus, pidincl; -unsigned short vs, vr, va; -unsigned char condition, backoff; -unsigned char n2, n2count; -struct timer_list t1timer, t2timer, t3timer, idletimer; -unsigned long t1, t2, t3, idle, rtt; -unsigned short paclen, fragno, fraglen; -struct sk_buff_head write_queue; -struct sk_buff_head reseq_queue; -struct sk_buff_head ack_queue; -struct sk_buff_head frag_queue; -unsigned char window; -struct timer_list timer, dtimer; -struct sock *sk;/* Backlink to socket */ -refcount_t refcount; -}ax25_cb ; - -struct ax25_sock { -struct sock sk; -struct ax25_cb *cb; -}; - -#define ax25_sk (ptr) container_of_const(ptr, struct ax25_sock, sk) - -static inline struct ax25_cb *sk_to_ax25 (const struct sock *sk) -{ -return ax25_sk (sk)->cb; -} - -#define ax25_for_each (__ax25, list) \ - hlist_for_each_entry(__ax25, list, ax25_node) - -#define ax25_cb_hold (__ax25) \ - refcount_inc(&((__ax25)->refcount)) - -static __inline__void ax25_cb_put (ax25_cb *ax25) -{ -if (refcount_dec_and_test (&ax25->refcount)) { -kfree (ax25->digipeat); -kfree (ax25); - } -} - -static inline void ax25_dev_hold (ax25_dev *ax25_dev) -{ -refcount_inc (&ax25_dev->refcount); -} - -static inline void ax25_dev_put (ax25_dev *ax25_dev) -{ -if (refcount_dec_and_test (&ax25_dev->refcount)) -kfree_rcu (ax25_dev, rcu); -} -static inline __be16 ax25_type_trans (struct sk_buff *skb,struct net_device *dev) -{ - skb->dev = dev; -skb_reset_mac_header (skb); - skb->pkt_type =PACKET_HOST ; -return htons (ETH_P_AX25 ); -} - -/* af_ax25.c */ -extern struct hlist_head ax25_list; -extern spinlock_t ax25_list_lock; -void ax25_cb_add (ax25_cb *); -struct sock *ax25_find_listener (ax25_address *,int ,struct net_device *,int ); -struct sock *ax25_get_socket (ax25_address *,ax25_address *,int ); -ax25_cb *ax25_find_cb (const ax25_address *,ax25_address *,ax25_digi *, -struct net_device *); -void ax25_send_to_raw (ax25_address *,struct sk_buff *,int ); -void ax25_destroy_socket (ax25_cb *); -ax25_cb *__must_check ax25_create_cb (void ); -void ax25_fillin_cb (ax25_cb *,ax25_dev *); -struct sock *ax25_make_new (struct sock *,struct ax25_dev *); - -/* ax25_addr.c */ -extern const ax25_address ax25_bcast; -extern const ax25_address ax25_defaddr; -extern const ax25_address null_ax25_address; -char *ax2asc (char *buf,const ax25_address *); -void asc2ax (ax25_address *addr,const char *callsign); -int ax25cmp (const ax25_address *,const ax25_address *); -int ax25digicmp (const ax25_digi *,const ax25_digi *); -const unsigned char *ax25_addr_parse (const unsigned char *,int , -ax25_address *,ax25_address *,ax25_digi *,int *,int *); -int ax25_addr_build (unsigned char *,const ax25_address *, -const ax25_address *,const ax25_digi *,int ,int ); -int ax25_addr_size (const ax25_digi *); -void ax25_digi_invert (const ax25_digi *,ax25_digi *); - -/* ax25_dev.c */ -extern spinlock_t ax25_dev_lock; - -#if IS_ENABLED (CONFIG_AX25 ) -static inline ax25_dev *ax25_dev_ax25dev (const struct net_device *dev) -{ -return rcu_dereference_rtnl (dev->ax25_ptr); -} -#endif - -ax25_dev *ax25_addr_ax25dev (ax25_address *); -void ax25_dev_device_up (struct net_device *); -void ax25_dev_device_down (struct net_device *); -int ax25_fwd_ioctl (unsigned int ,struct ax25_fwd_struct *); -struct net_device *ax25_fwd_dev (struct net_device *); -void ax25_dev_free (void ); - -/* ax25_ds_in.c */ -int ax25_ds_frame_in (ax25_cb *,struct sk_buff *,int ); - -/* ax25_ds_subr.c */ -void ax25_ds_nr_error_recovery (ax25_cb *); -void ax25_ds_enquiry_response (ax25_cb *); -void ax25_ds_establish_data_link (ax25_cb *); -void ax25_dev_dama_off (ax25_dev *); -void ax25_dama_on (ax25_cb *); -void ax25_dama_off (ax25_cb *); - -/* ax25_ds_timer.c */ -void ax25_ds_setup_timer (ax25_dev *); -void ax25_ds_set_timer (ax25_dev *); -void ax25_ds_del_timer (ax25_dev *); -void ax25_ds_timer (ax25_cb *); -void ax25_ds_t1_timeout (ax25_cb *); -void ax25_ds_heartbeat_expiry (ax25_cb *); -void ax25_ds_t3timer_expiry (ax25_cb *); -void ax25_ds_idletimer_expiry (ax25_cb *); - -/* ax25_iface.c */ - -struct ax25_protocol { -struct ax25_protocol *next; -unsigned int pid; -int (*func)(struct sk_buff *,ax25_cb *); -}; - -void ax25_register_pid (struct ax25_protocol *ap); -void ax25_protocol_release (unsigned int ); - -struct ax25_linkfail { -struct hlist_node lf_node; -void (*func)(ax25_cb *,int ); -}; - -void ax25_linkfail_register (struct ax25_linkfail *lf); -void ax25_linkfail_release (struct ax25_linkfail *lf); -int __must_check ax25_listen_register (const ax25_address *, -struct net_device *); -void ax25_listen_release (const ax25_address *,struct net_device *); -int (*ax25_protocol_function (unsigned int ))(struct sk_buff *,ax25_cb *); -int ax25_listen_mine (const ax25_address *,struct net_device *); -void ax25_link_failed (ax25_cb *,int ); -int ax25_protocol_is_registered (unsigned int ); - -/* ax25_in.c */ -int ax25_rx_iframe (ax25_cb *,struct sk_buff *); -int ax25_kiss_rcv (struct sk_buff *,struct net_device *,struct packet_type *, -struct net_device *); - -/* ax25_ip.c */ -netdev_tx_t ax25_ip_xmit (struct sk_buff *skb); -extern const struct header_ops ax25_header_ops; - -/* ax25_out.c */ -ax25_cb *ax25_send_frame (struct sk_buff *,int ,const ax25_address *, -ax25_address *,ax25_digi *,struct net_device *); -void ax25_output (ax25_cb *,int ,struct sk_buff *); -void ax25_kick (ax25_cb *); -void ax25_transmit_buffer (ax25_cb *,struct sk_buff *,int ); -void ax25_queue_xmit (struct sk_buff *skb,struct net_device *dev); -int ax25_check_iframes_acked (ax25_cb *,unsigned short ); - -/* ax25_route.c */ -void ax25_rt_device_down (struct net_device *); -int ax25_rt_ioctl (unsigned int ,void __user *); -extern const struct seq_operations ax25_rt_seqops; -ax25_route *ax25_get_route (ax25_address *addr,struct net_device *dev); -struct sk_buff *ax25_rt_build_path (struct sk_buff *,ax25_address *, -ax25_address *,ax25_digi *); -void ax25_rt_free (void ); - -/* ax25_std_in.c */ -int ax25_std_frame_in (ax25_cb *,struct sk_buff *,int ); - -/* ax25_std_subr.c */ -void ax25_std_nr_error_recovery (ax25_cb *); -void ax25_std_establish_data_link (ax25_cb *); -void ax25_std_transmit_enquiry (ax25_cb *); -void ax25_std_enquiry_response (ax25_cb *); -void ax25_std_timeout_response (ax25_cb *); - -/* ax25_std_timer.c */ -void ax25_std_heartbeat_expiry (ax25_cb *); -void ax25_std_t1timer_expiry (ax25_cb *); -void ax25_std_t2timer_expiry (ax25_cb *); -void ax25_std_t3timer_expiry (ax25_cb *); -void ax25_std_idletimer_expiry (ax25_cb *); - -/* ax25_subr.c */ -void ax25_clear_queues (ax25_cb *); -void ax25_frames_acked (ax25_cb *,unsigned short ); -void ax25_requeue_frames (ax25_cb *); -int ax25_validate_nr (ax25_cb *,unsigned short ); -int ax25_decode (ax25_cb *,struct sk_buff *,int *,int *,int *); -void ax25_send_control (ax25_cb *,int ,int ,int ); -void ax25_return_dm (struct net_device *,ax25_address *,ax25_address *, -ax25_digi *); -void ax25_calculate_t1 (ax25_cb *); -void ax25_calculate_rtt (ax25_cb *); -void ax25_disconnect (ax25_cb *,int ); - -/* ax25_timer.c */ -void ax25_setup_timers (ax25_cb *); -void ax25_start_heartbeat (ax25_cb *); -void ax25_start_t1timer (ax25_cb *); -void ax25_start_t2timer (ax25_cb *); -void ax25_start_t3timer (ax25_cb *); -void ax25_start_idletimer (ax25_cb *); -void ax25_stop_heartbeat (ax25_cb *); -void ax25_stop_t1timer (ax25_cb *); -void ax25_stop_t2timer (ax25_cb *); -void ax25_stop_t3timer (ax25_cb *); -void ax25_stop_idletimer (ax25_cb *); -int ax25_t1timer_running (ax25_cb *); -unsigned long ax25_display_timer (struct timer_list *); - -/* ax25_uid.c */ -extern int ax25_uid_policy; -ax25_uid_assoc *ax25_findbyuid (kuid_t ); -int __must_check ax25_uid_ioctl (int ,struct sockaddr_ax25 *); -extern const struct seq_operations ax25_uid_seqops; -void ax25_uid_free (void ); - -/* sysctl_net_ax25.c */ -#ifdef CONFIG_SYSCTL -int ax25_register_dev_sysctl (ax25_dev *ax25_dev); -void ax25_unregister_dev_sysctl (ax25_dev *ax25_dev); -#else -static inline int ax25_register_dev_sysctl (ax25_dev *ax25_dev) {return 0 ; } -static inline void ax25_unregister_dev_sysctl (ax25_dev *ax25_dev) {} -#endif /* CONFIG_SYSCTL */ +#define AX25_ADDR_LEN 7 +#define AX25_P_IP 0xCC#endif include/net/netrom.h deleted +0
-273@@ -1,273 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* -* Declarations of NET/ROM type objects. -* -* Jonathan Naylor G4KLX 9/4/95 -*/ - -#ifndef _NETROM_H -#define _NETROM_H - -#include <linux/netrom.h> -#include <linux/list.h> -#include <linux/slab.h> -#include <net/sock.h> -#include <linux/refcount.h> -#include <linux/seq_file.h> -#include <net/ax25.h> - -#define NR_NETWORK_LEN 15 -#define NR_TRANSPORT_LEN 5 - -#define NR_PROTO_IP 0x0C - -#define NR_PROTOEXT 0x00 -#define NR_CONNREQ 0x01 -#define NR_CONNACK 0x02 -#define NR_DISCREQ 0x03 -#define NR_DISCACK 0x04 -#define NR_INFO 0x05 -#define NR_INFOACK 0x06 -#define NR_RESET 0x07 - -#define NR_CHOKE_FLAG 0x80 -#define NR_NAK_FLAG 0x40 -#define NR_MORE_FLAG 0x20 - -/* Define Link State constants. */ -enum { -NR_STATE_0 , -NR_STATE_1 , -NR_STATE_2 , -NR_STATE_3 -}; - -#define NR_COND_ACK_PENDING 0x01 -#define NR_COND_REJECT 0x02 -#define NR_COND_PEER_RX_BUSY 0x04 -#define NR_COND_OWN_RX_BUSY 0x08 - -#define NR_DEFAULT_T1 120000/* Outstanding frames - 120 seconds */ -#define NR_DEFAULT_T2 5000/* Response delay - 5 seconds */ -#define NR_DEFAULT_N2 3/* Number of Retries - 3 */ -#define NR_DEFAULT_T4 180000/* Busy Delay - 180 seconds */ -#define NR_DEFAULT_IDLE 0/* No Activity Timeout - none */ -#define NR_DEFAULT_WINDOW 4/* Default Window Size - 4 */ -#define NR_DEFAULT_OBS 6/* Default Obsolescence Count - 6 */ -#define NR_DEFAULT_QUAL 10/* Default Neighbour Quality - 10 */ -#define NR_DEFAULT_TTL 16/* Default Time To Live - 16 */ -#define NR_DEFAULT_ROUTING 1/* Is routing enabled ? */ -#define NR_DEFAULT_FAILS 2/* Link fails until route fails */ -#define NR_DEFAULT_RESET 0/* Sent / accept reset cmds? */ - -#define NR_MODULUS 256 -#define NR_MAX_WINDOW_SIZE 127/* Maximum Window Allowable - 127 */ -#define NR_MAX_PACKET_SIZE 236/* Maximum Packet Length - 236 */ - -struct nr_sock { -struct sock sock; -ax25_address user_addr, source_addr, dest_addr; -struct net_device *device; -unsigned char my_index, my_id; -unsigned char your_index, your_id; -unsigned char state, condition, bpqext, window; -unsigned short vs, vr, va, vl; -unsigned char n2, n2count; -unsigned long t1, t2, t4, idle; -unsigned short fraglen; -struct timer_list t1timer; -struct timer_list t2timer; -struct timer_list t4timer; -struct timer_list idletimer; -struct sk_buff_head ack_queue; -struct sk_buff_head reseq_queue; -struct sk_buff_head frag_queue; -}; - -#define nr_sk (sk) ((struct nr_sock *)(sk)) - -struct nr_neigh { -struct hlist_node neigh_node; -ax25_address callsign; -ax25_digi *digipeat; -ax25_cb *ax25; -struct net_device *dev; -unsigned char quality; -unsigned char locked; -unsigned short count; -unsigned int number; -unsigned char failed; -refcount_t refcount; -}; - -struct nr_route { -unsigned char quality; -unsigned char obs_count; -struct nr_neigh *neighbour; -}; - -struct nr_node { -struct hlist_node node_node; -ax25_address callsign; -char mnemonic[7 ]; -unsigned char which; -unsigned char count; -struct nr_route routes[3 ]; -refcount_t refcount; -spinlock_t node_lock; -}; - -/********************************************************************* -* nr_node & nr_neigh lists, refcounting and locking -*********************************************************************/ - -#define nr_node_hold (__nr_node) \ - refcount_inc(&((__nr_node)->refcount)) - -static __inline__void nr_node_put (struct nr_node *nr_node) -{ -if (refcount_dec_and_test (&nr_node->refcount)) { -kfree (nr_node); - } -} - -#define nr_neigh_hold (__nr_neigh) \ - refcount_inc(&((__nr_neigh)->refcount)) - -static __inline__void nr_neigh_put (struct nr_neigh *nr_neigh) -{ -if (refcount_dec_and_test (&nr_neigh->refcount)) { -if (nr_neigh->ax25) -ax25_cb_put (nr_neigh->ax25); -kfree (nr_neigh->digipeat); -kfree (nr_neigh); - } -} - -/* nr_node_lock and nr_node_unlock also hold/put the node's refcounter. -*/ -static __inline__void nr_node_lock (struct nr_node *nr_node) -{ -nr_node_hold (nr_node); -spin_lock_bh (&nr_node->node_lock); -} - -static __inline__void nr_node_unlock (struct nr_node *nr_node)Lines of this file are not shown. View the raw message.
drivers/net/hamradio/baycom_epp.c deleted +0
-1316Lines of this file are not shown. View the raw message.
drivers/net/hamradio/baycom_par.c deleted +0
-598Lines of this file are not shown. View the raw message.
drivers/net/hamradio/baycom_ser_fdx.c deleted +0
-678Lines of this file are not shown. View the raw message.
drivers/net/hamradio/baycom_ser_hdx.c deleted +0
-727Lines of this file are not shown. View the raw message.
drivers/net/hamradio/bpqether.c deleted +0
-593Lines of this file are not shown. View the raw message.
drivers/net/hamradio/hdlcdrv.c deleted +0
-747Lines of this file are not shown. View the raw message.
net/netrom/sysctl_net_netrom.c deleted +0
-156Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
Part of the diff is not shown here. View the raw message.
Quoted 11 lines · Jakub Kicinski
Remove the amateur radio (AX.25, NET/ROM, ROSE) protocol implementation and all associated hamradio device drivers from the kernel tree. This set of protocols has long been a huge bug/syzbot magnet, and since nobody stepped up to help us deal with the influx of the AI-generated bug reports we need to move it out of tree to protect our sanity.
The code is moved to an out-of-tree repo:
https://github.com/linux-netdev/mod-orphan
if it's cleaned up and reworked there we can accept it back.
Quoted 6 lines
Minimal stub headers are kept for
include/net/ax25.h(AX25_P_IP,AX25_ADDR_LEN,ax25_address) andinclude/net/rose.h(ROSE_ADDR_LEN) so that the conditional integration code inarp.candtun.ccontinues to compile and work when the out-of-tree modules are loaded.Signed-off-by Jakub Kicinski <[email protected]>
Kuniyuki Iwashima
Reviewed-byQuoted 11 lines · Jakub Kicinski
Remove the amateur radio (AX.25, NET/ROM, ROSE) protocol implementation and all associated hamradio device drivers from the kernel tree. This set of protocols has long been a huge bug/syzbot magnet, and since nobody stepped up to help us deal with the influx of the AI-generated bug reports we need to move it out of tree to protect our sanity.
The code is moved to an out-of-tree repo:
https://github.com/linux-netdev/mod-orphan
if it's cleaned up and reworked there we can accept it back.
Quoted 6 lines
Minimal stub headers are kept for
include/net/ax25.h(AX25_P_IP,AX25_ADDR_LEN,ax25_address) andinclude/net/rose.h(ROSE_ADDR_LEN) so that the conditional integration code inarp.candtun.ccontinues to compile and work when the out-of-tree modules are loaded.Signed-off-by Jakub Kicinski <[email protected]>
Quoted 11 lines · Jakub Kicinski
Remove the amateur radio (AX.25, NET/ROM, ROSE) protocol implementation and all associated hamradio device drivers from the kernel tree. This set of protocols has long been a huge bug/syzbot magnet, and since nobody stepped up to help us deal with the influx of the AI-generated bug reports we need to move it out of tree to protect our sanity.
The code is moved to an out-of-tree repo:
https://github.com/linux-netdev/mod-orphan
if it's cleaned up and reworked there we can accept it back.
Quoted 6 lines
Minimal stub headers are kept for
include/net/ax25.h(AX25_P_IP,AX25_ADDR_LEN,ax25_address) andinclude/net/rose.h(ROSE_ADDR_LEN) so that the conditional integration code inarp.candtun.ccontinues to compile and work when the out-of-tree modules are loaded.Signed-off-by Jakub Kicinski <[email protected]>
From: Bernard Pidoux <[email protected]>
Quoted 1 line · Toke Høiland-Jørgensen
Hello Toke, Jakub, all,
I understand the decision to move AX.25, NET/ROM, and ROSE out of tree, and I am not opposing it. The maintenance burden caused by AI-generated syzbot reports with no human follow-up is a legitimate reason to act.
That said, I would like to raise one specific concern: the ROSE subsystem accumulated a number of real bugs through upstream commits that were merged without hardware testing. I have been running ROSE on actual packet radio equipment and was able to reproduce and fix five of these bugs, confirmed via KASAN and netconsole.
The most severe symptom is that the ROSE module cannot be cleanly unloaded once an AX.25 connection has been established, which makes amateur radio applications that rely on ROSE effectively unusable until a reboot.
My five patches address:
1. rose: fix dev_put() leak in rose_loopback_timer()
2. rose: hold loopback neighbour reference across timer callback
3. rose: fix race between loopback timer and module removal
4. rose: clear neighbour pointer after rose_neigh_put() in state machines
5. rose: guard rose_neigh_put() against NULL in timer expiry
Each patch carries the appropriate Fixes: tag and a Tested-by from me on real hardware. They are visible on lore.kernel.org.
Since ROSE will no longer be maintained in-tree from 7.1 onward, the only remaining users are those running current stable kernels (7.0.y and earlier). Would it be possible to have these five patches queued for the stable trees via Greg's stable process?
I am happy to resend them as a formal series tagged [PATCH stable] against the current stable releases if that is preferred.
Thank you for your work on the Linux networking subsystem.
73 de Bernard Pidoux, F6BVP
<[email protected]>
From: Bernard Pidoux <[email protected]>
Quoted 1 line · Toke Høiland-Jørgensen
Hello Toke, Jakub, all,
I understand the decision to move AX.25, NET/ROM, and ROSE out of tree, and I am not opposing it. The maintenance burden caused by AI-generated syzbot reports with no human follow-up is a legitimate reason to act.
That said, I would like to raise one specific concern: the ROSE subsystem accumulated a number of real bugs through upstream commits that were merged without hardware testing. I have been running ROSE on actual packet radio equipment and was able to reproduce and fix five of these bugs, confirmed via KASAN and netconsole.
The most severe symptom is that the ROSE module cannot be cleanly unloaded once an AX.25 connection has been established, which makes amateur radio applications that rely on ROSE effectively unusable until a reboot.
My five patches address:
1. rose: fix dev_put() leak in rose_loopback_timer()
2. rose: hold loopback neighbour reference across timer callback
3. rose: fix race between loopback timer and module removal
4. rose: clear neighbour pointer after rose_neigh_put() in state machines
5. rose: guard rose_neigh_put() against NULL in timer expiry
Each patch carries the appropriate Fixes: tag and a Tested-by from me on real hardware. They are visible on lore.kernel.org.
Since ROSE will no longer be maintained in-tree from 7.1 onward, the only remaining users are those running current stable kernels (7.0.y and earlier). Would it be possible to have these five patches queued for the stable trees via Greg's stable process?
I am happy to resend them as a formal series tagged [PATCH stable] against the current stable releases if that is preferred.
Thank you for your work on the Linux networking subsystem.
73 de Bernard Pidoux, F6BVP
<[email protected]>
Jakub Kicinski
maintainerQuoted 10 lines · On Tue, 12 May 2026 16:45:10 +0200 f6bvp wrote:
Each patch carries the appropriate Fixes: tag and a Tested-by from me on real hardware. They are visible on lore.kernel.org.
Since ROSE will no longer be maintained in-tree from 7.1 onward, the only remaining users are those running current stable kernels (7.0.y and earlier). Would it be possible to have these five patches queued for the stable trees via Greg's stable process?
I am happy to resend them as a formal series tagged [PATCH stable] against the current stable releases if that is preferred.
Could you perhaps target the OOT modules?
https://github.com/linux-netdev/mod-orphan
Does it work with older kernels? I think I compile-tested it but didn't do any testing..
A message that is not in the archive (sent off-list or not yet received): CAFAa3YDcBsCnEJ1t+a3iHhzxW65HX+QNkZWPKHvDYp_V+UwZYQ@mail.gmail.com
Jakub Kicinski
maintainerQuoted 2 lines · On Fri, 15 May 2026 16:52:43 +0200 Bernard Pidoux wrote:
I am happy to submit these two fixes as patches to mod-orphan if that is the right approach. Please let me know.
It's a GitHub repo so PR is probably appropriate there.
Quoted 1 line · On Fri, 16 May 2026 Jakub Kicinski wrote:
It's a GitHub repo so PR is probably appropriate there.
Done. I have submitted the five rose fixes as a pull request to the mod-orphan repository:
https://github.com/linux-netdev/mod-orphan/pull/1
The PR contains six commits:
1. rose: build with hamradio_compat.h on pre-7.0 kernels (compat shim for struct sockaddr_unsized, required by af_rose.c)
2. rose: fix dev_put() leak in rose_loopback_timer()
3. rose: hold loopback neighbour reference across timer callback
4. rose: fix race between loopback timer and module removal
5. rose: clear neighbour pointer after rose_neigh_put() in state machines
6. rose: guard rose_neigh_put() against NULL in timer expiry
All five fixes have been built and tested successfully against kernel 6.17.0-23-generic (pre-7.0): insmod, functional operation, and rmmod all completed cleanly with no crash or leak detected.
73 de Bernard Pidoux F6BVP
Quoted 6 lines · Jakub Kicinski
Quoted 2 lines · On Fri, 15 May 2026 16:52:43 +0200 Bernard Pidoux wrote:
I am happy to submit these two fixes as patches to mod-orphan if that is the right approach. Please let me know.
It's a GitHub repo so PR is probably appropriate there.
Quoted 1 line · On Fri, 16 May 2026 Jakub Kicinski wrote:
It's a GitHub repo so PR is probably appropriate there.
Done. I have submitted the five rose fixes as a pull request to the mod-orphan repository:
https://github.com/linux-netdev/mod-orphan/pull/1
The PR contains six commits:
1. rose: build with hamradio_compat.h on pre-7.0 kernels (compat shim for struct sockaddr_unsized, required by af_rose.c)
2. rose: fix dev_put() leak in rose_loopback_timer()
3. rose: hold loopback neighbour reference across timer callback
4. rose: fix race between loopback timer and module removal
5. rose: clear neighbour pointer after rose_neigh_put() in state machines
6. rose: guard rose_neigh_put() against NULL in timer expiry
All five fixes have been built and tested successfully against kernel 6.17.0-23-generic (pre-7.0): insmod, functional operation, and rmmod all completed cleanly with no crash or leak detected.
73 de Bernard Pidoux F6BVP
Quoted 6 lines · Jakub Kicinski
Quoted 2 lines · On Fri, 15 May 2026 16:52:43 +0200 Bernard Pidoux wrote:
I am happy to submit these two fixes as patches to mod-orphan if that is the right approach. Please let me know.
It's a GitHub repo so PR is probably appropriate there.
Paolo Abeni
maintainerinclude/linux/netdevice.h struct net_device { · line 2321
Quoted 7 lines · Jakub Kicinski
include/linux/netdevice.h +0
-3@@ -2316,9 +2316,6 @@ struct net_device {#if IS_ENABLED (CONFIG_ATALK )void *atalk_ptr;#endif -#if IS_ENABLED (CONFIG_AX25 ) -struct ax25_dev __rcu *ax25_ptr; -#endif
AI reviews notes that this leaves behind a stray doxygen comment. I think we are better off with a follow-up that with a v2.
/P
Paolo Abeni
maintainerQuoted 11 lines · Paolo Abeni
include/linux/netdevice.h struct net_device { · line 2321
Quoted 7 lines · Jakub Kicinski
include/linux/netdevice.h +0
-3@@ -2316,9 +2316,6 @@ struct net_device {#if IS_ENABLED (CONFIG_ATALK )void *atalk_ptr;#endif -#if IS_ENABLED (CONFIG_AX25 ) -struct ax25_dev __rcu *ax25_ptr; -#endif AI reviews notes that this leaves behind a stray doxygen comment. I think we are better off with a follow-up that with a v2.
Or even better, I'll clean it up while applying it.
/P
Quoted 15 lines · Jakub Kicinski
Remove the amateur radio (AX.25, NET/ROM, ROSE) protocol implementation and all associated hamradio device drivers from the kernel tree. This set of protocols has long been a huge bug/syzbot magnet, and since nobody stepped up to help us deal with the influx of the AI-generated bug reports we need to move it out of tree to protect our sanity.
The code is moved to an out-of-tree repo:
https://github.com/linux-netdev/mod-orphan
if it's cleaned up and reworked there we can accept it back.Minimal stub headers are kept for
include/net/ax25.h(AX25_P_IP,AX25_ADDR_LEN,ax25_address) andinclude/net/rose.h(ROSE_ADDR_LEN) so that the conditional integration code inarp.candtun.ccontinues to compile and work when the out-of-tree modules are loaded.
...
Quoted 1 line
delete mode 100644
include/uapi/linux/scc.h
Unfortunately, this broke builds of LLVM -- compiler-rt in particular (and GCC builds allegedly too). They dropped the include and its use [1], but IMO we should keep the uapi header with those two structs (scc_modem + scc_stat) for some time.
[1] https://github.com/llvm/llvm-project/commit/3dc4fd6dd41100f051a63642f449b16324389c96
thanks,
Signature · 2 lines
js suse labs
Quoted 16 lines · Jiri Slaby
Quoted 7 lines · Jakub Kicinski
Remove the amateur radio (AX.25, NET/ROM, ROSE) protocol implementation and all associated hamradio device drivers from the kernel tree. This set of protocols has long been a huge bug/syzbot magnet, and since nobody stepped up to help us deal with the influx of the AI-generated bug reports we need to move it out of tree to protect our sanity.
Quoted 8 lines
The code is moved to an out-of-tree repo:
https://github.com/linux-netdev/mod-orphan
if it's cleaned up and reworked there we can accept it back.Minimal stub headers are kept for
include/net/ax25.h(AX25_P_IP,AX25_ADDR_LEN,ax25_address) andinclude/net/rose.h(ROSE_ADDR_LEN) so that the conditional integration code inarp.candtun.ccontinues to compile and work when the out-of-tree modules are loaded.
Quoted 5 lines
...
Quoted 1 line
delete mode 100644
include/uapi/linux/scc.hUnfortunately, this broke builds of LLVM -- compiler-rt in particular (and GCC builds allegedly too). They dropped the include and its use [1], but IMO we should keep the uapi header with those two structs (
scc_modem+scc_stat) for some time.[1] https://github.com/llvm/llvm-project/ commit/3dc4fd6dd41100f051a63642f449b16324389c96
And net-tools are broken by the uapi/linux/rose.h removal:
rose.c:39:10: fatal error: linux/rose.h: No such file or directory
at:
https://github.com/ecki/net-tools/blob/2ab3c5efdb5c220bc9a649fded56c361136bff1a/lib/rose.c#L39
Quoted 2 lines
thanks,
Signature · 2 lines
js suse labs
Jakub Kicinski
maintainerQuoted 4 lines · On Mon, 29 Jun 2026 07:24:51 +0200 Jiri Slaby wrote:
And net-tools are broken by the
uapi/linux/rose.hremoval:
rose.c:39:10: fatal error:linux/rose.h: No such file or directory
at:
https://github.com/ecki/net-tools/blob/2ab3c5efdb5c220bc9a649fded56c361136bff1a/lib/rose.c#L39
Looks like the code for rose is already well separated from the rest. Should we just ask net-tools to delete it? Or do you feel strongly about restoring the now-defunct header?
Quoted 9 lines · Jakub Kicinski
Quoted 4 lines · On Mon, 29 Jun 2026 07:24:51 +0200 Jiri Slaby wrote:
And net-tools are broken by the
uapi/linux/rose.hremoval:
rose.c:39:10: fatal error:linux/rose.h: No such file or directory
at:
https://github.com/ecki/net-tools/blob/2ab3c5efdb5c220bc9a649fded56c361136bff1a/lib/rose.c#L39Looks like the code for rose is already well separated from the rest. Should we just ask net-tools to delete it? Or do you feel strongly about restoring the now-defunct header?
No strong opinion from me. net-tools are easy to fix.
The builds of LLVMs (versions 15 to 21 at least) are broken nonetheless. They are easy to fix as well -- by backporting the fix from main or 22. (15--21 are likely unmaintained upstream already, but still used/required widely).
$ osc whatdependson openSUSE:Factory llvm19 standard x86_64
llvm19 :
MozillaThunderbird
firefox-esr
ghc
gtkd
ldc
lfortran
python-PyMuPDF
redumper
tilix
zig0.14$ osc whatdependson openSUSE:Factory llvm21 standard x86_64
llvm21 :
OpenImageDenoise
chromium
embree
ispc
leechcraft
python-PyMuPDF
python314
python314:base
python314:doc
python315
python315:base
python315:doc
rpcs3
rust-keylime
zig0.16thanks,
Signature · 2 lines
js suse labs