Skip to contentSkip to conversation

How to re-merge paths differently?

DISCUSSION Sergey Organov 2 participants 4 messages Oct 27, 2017 – Oct 30, 2017

lore
Share & tools
lore
#0 lore raw

Hello,

Is there anything like this:

$ git merge b
[... lot of conflicts ...]
$ git re-merge -X ours -- x/   # Leaves 0 conflicts in x/
$ git re-merge -X theirs -- y/ # Leaves 0 conflicts in y/
[... resolve the rest of conflicts manually ...]
$ git commit

[*] I do mean '-X' above, not '-s'.

-- Sergey

#1 lore raw

From: "Sergey Organov" <[email protected]>

Quoted 11 lines

Is there anything like this:

$ git merge b
[... lot of conflicts ...]
$ git re-merge -X ours -- x/   # Leaves 0 conflicts in x/
$ git re-merge -X theirs -- y/ # Leaves 0 conflicts in y/
[... resolve the rest of conflicts manually ...]
$ git commit

[*] I do mean '-X' above, not '-s'.

By this I presume you mean that you have paths x and y that ate the ones with conflicts within them following the git merge b.

You then want a variant of the git merge command that will apply the -X ours policy *specifically to path x* so that its particular set of conflicts is fully resolved in favour of 'ours'.

You then want to repeat those path specific resolutions, on a path by path basis, to either -X ours or -X theirs until they are done.

You are also expecting that one or two conflicts will require to be fully manually resolved, until finally you can commit the result.

Would that be right?

Also, how do you intend to identify the 'x' and the 'y' paths, so that you can chose the ours/theirs/manual selection? (e.g. do you pre-know a regex/blob expansion)

The answer for individual paths is probably in the mergetool of your choice. --
Philip

#2 lore raw

From: "Philip Oakley" <[email protected]>

Quoted 10 lines

From: "Sergey Organov" <[email protected]>

Quoted 9 lines

Is there anything like this:

$ git merge b
[... lot of conflicts ...]
$ git re-merge -X ours -- x/   # Leaves 0 conflicts in x/
$ git re-merge -X theirs -- y/ # Leaves 0 conflicts in y/
[... resolve the rest of conflicts manually ...]
$ git commit
Quoted 4 lines
Quoted 2 lines

[*] I do mean '-X' above, not '-s'.

By this I presume you mean that you have paths x and y that ate the ones

s/ate/are/

Quoted 2 lines

with conflicts within them following the git merge b.

[snip]

#3 lore raw
In reply to Philip Oakley
Quoted 10 lines · Philip Oakley

From: "Sergey Organov" <[email protected]>

Quoted 9 lines

Is there anything like this:

$ git merge b
[... lot of conflicts ...]
$ git re-merge -X ours -- x/   # Leaves 0 conflicts in x/
$ git re-merge -X theirs -- y/ # Leaves 0 conflicts in y/
[... resolve the rest of conflicts manually ...]
$ git commit
Quoted 5 lines
Quoted 2 lines

[*] I do mean '-X' above, not '-s'.

By this I presume you mean that you have paths x and y that ate the ones with conflicts within them following the git merge b.

I rather mean huge amount of conflicting paths in 'x' and 'y' subdirectories of my working tree after a merge, plus a few conflicting paths elsewhere.

Quoted 4 lines

You then want a variant of the git merge command that will apply the -X ours policy *specifically to path x* so that its particular set of conflicts is fully resolved in favour of 'ours'.

Almost. I mean to apply 'ours' option to the default 'recursive' policy for all the files that reside in the directory 'x' of my working tree and all its subdirectories (i.e., all the paths 'x/*')

Quoted 3 lines

You then want to repeat those path specific resolutions, on a path by path basis, to either -X ours or -X theirs until they are done.

No. I mean to apply '-X ours' to everything under 'x/', and '-X theirs' to everything under 'y/'. Avoiding to repeat anything is the intention.

Quoted 2 lines

You are also expecting that one or two conflicts will require to be fully manually resolved, until finally you can commit the result.

No, I expect no conflicts left in either 'x/' or 'y/' after "re-merge", as neither 'theirs' or 'ours' should leave anything unresolved, and all the other conflicting paths (left from original merge elsewhere) I mean to resolve manually.

Quoted 6 lines

Would that be right?

Also, how do you intend to identify the 'x' and the 'y' paths, so that you can chose the ours/theirs/manual selection? (e.g. do you pre-know a regex/blob expansion)

All the 'x/*' paths need 'ours', and all the 'y/*' paths need 'theirs'.

Quoted 3 lines

The answer for individual paths is probably in the mergetool of your choice.

There are a lot of files under 'x/' and a lot of them under 'y/'. My intention is to automate a lot of manual labor, and I'm not aware of a mergetool that provides either '-X ours' or '-X theirs' resolution automatically for all the paths specified.

-- Sergey