Skip to contentSkip to conversation

ath10k: fix comments style in rx_desc.h file

PATCH New Bartosz Markowski 2 participants 2 messages Apr 24, 2013 – Apr 25, 2013 Qualcomm Atheros ATH10K wireless driver

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ath10k: fix comments style in rx_desc.h file

---
 drivers/net/wireless/ath/ath10k/rx_desc.h | 1360 ++++++++++++++---------------
 1 file changed, 680 insertions(+), 680 deletions(-)
drivers/net/wireless/ath/ath10k/rx_desc.h +680 -680
index e3df696..f203614 100644
@@ -58,152 +58,152 @@ struct rx_attention {
 } __packed;
 
 /*
-first_mpdu
-		Indicates the first MSDU of the PPDU.  If both first_mpdu
-		and last_mpdu are set in the MSDU then this is a not an
-		A-MPDU frame but a stand alone MPDU.  Interior MPDU in an
-		A-MPDU shall have both first_mpdu and last_mpdu bits set to
-		0.  The PPDU start status will only be valid when this bit
-		is set.
-
-last_mpdu
-		Indicates the last MSDU of the last MPDU of the PPDU.  The
-		PPDU end status will only be valid when this bit is set.
-
-mcast_bcast
-		Multicast / broadcast indicator.  Only set when the MAC
-		address 1 bit 0 is set indicating mcast/bcast and the BSSID
-		matches one of the 4 BSSID registers. Only set when
-		first_msdu is set.
-
-peer_idx_invalid
-		Indicates no matching entries within the the max search
-		count.  Only set when first_msdu is set.
-
-peer_idx_timeout
-		Indicates an unsuccessful search for the peer index due to
-		timeout.  Only set when first_msdu is set.
-
-power_mgmt
-		Power management bit set in the 802.11 header.  Only set
-		when first_msdu is set.
-
-non_qos
-		Set if packet is not a non-QoS data frame.  Only set when
-		first_msdu is set.
-
-null_data
-		Set if frame type indicates either null data or QoS null
-		data format.  Only set when first_msdu is set.
-
-mgmt_type
-		Set if packet is a management packet.  Only set when
-		first_msdu is set.
-
-ctrl_type
-		Set if packet is a control packet.  Only set when first_msdu
-		is set.
-
-more_data
-		Set if more bit in frame control is set.  Only set when
-		first_msdu is set.
-
-eosp
-		Set if the EOSP (end of service period) bit in the QoS
-		control field is set.  Only set when first_msdu is set.
-
-u_apsd_trigger
-		Set if packet is U-APSD trigger.  Key table will have bits
-		per TID to indicate U-APSD trigger.
-
-fragment
-		Indicates that this is an 802.11 fragment frame.  This is
-		set when either the more_frag bit is set in the frame
-		control or the fragment number is not zero.  Only set when
-		first_msdu is set.
-
-order
-		Set if the order bit in the frame control is set.  Only set
-		when first_msdu is set.
-
-classification
-		Indicates that this status has a corresponding MSDU that
-		requires FW processing.  The OLE will have classification
-		ring mask registers which will indicate the ring(s) for
-		packets and descriptors which need FW attention.
-
-overflow_err
-		PCU Receive FIFO does not have enough space to store the
-		full receive packet.  Enough space is reserved in the
-		receive FIFO for the status is written.  This MPDU remaining
-		packets in the PPDU will be filtered and no Ack response
-		will be transmitted.
-
-msdu_length_err
-		Indicates that the MSDU length from the 802.3 encapsulated
-		length field extends beyond the MPDU boundary.
-
-tcp_udp_chksum_fail
-		Indicates that the computed checksum (tcp_udp_chksum) did
-		not match the checksum in the TCP/UDP header.
-
-ip_chksum_fail
-		Indicates that the computed checksum did not match the
-		checksum in the IP header.
-
-sa_idx_invalid
-		Indicates no matching entry was found in the address search
-		table for the source MAC address.
-
-da_idx_invalid
-		Indicates no matching entry was found in the address search
-		table for the destination MAC address.
-
-sa_idx_timeout
-		Indicates an unsuccessful search for the source MAC address
-		due to the expiring of the search timer.
-
-da_idx_timeout
-		Indicates an unsuccessful search for the destination MAC
-		address due to the expiring of the search timer.
-
-encrypt_required
-		Indicates that this data type frame is not encrypted even if
-		the policy for this MPDU requires encryption as indicated in
-		the peer table key type.
-
-directed
-		MPDU is a directed packet which means that the RA matched
-		our STA addresses.  In proxySTA it means that the TA matched
-		an entry in our address search table with the corresponding
-		'no_ack' bit is the address search entry cleared.
-
-buffer_fragment
-		Indicates that at least one of the rx buffers has been
-		fragmented.  If set the FW should look at the rx_frag_info
-		descriptor described below.
-
-mpdu_length_err
-		Indicates that the MPDU was pre-maturely terminated
-		resulting in a truncated MPDU.  Don't trust the MPDU length
-		field.
-
-tkip_mic_err
-		Indicates that the MPDU Michael integrity check failed
-
-decrypt_err
-		Indicates that the MPDU decrypt integrity check failed
-
-fcs_err
-		Indicates that the MPDU FCS check failed
-
-msdu_done
-		If set indicates that the RX packet data, RX header data, RX
-		PPDU start descriptor, RX MPDU start/end descriptor, RX MSDU
-		start/end descriptors and RX Attention descriptor are all
-		valid.  This bit must be in the last octet of the
-		descriptor.
-*/
+ * first_mpdu
+ *		Indicates the first MSDU of the PPDU.  If both first_mpdu
+ *		and last_mpdu are set in the MSDU then this is a not an
+ *		A-MPDU frame but a stand alone MPDU.  Interior MPDU in an
+ *		A-MPDU shall have both first_mpdu and last_mpdu bits set to
+ *		0.  The PPDU start status will only be valid when this bit
+ *		is set.
+ *
+ * last_mpdu
+ *		Indicates the last MSDU of the last MPDU of the PPDU.  The
+ *		PPDU end status will only be valid when this bit is set.
+ *
+ * mcast_bcast
+ *		Multicast / broadcast indicator.  Only set when the MAC
+ *		address 1 bit 0 is set indicating mcast/bcast and the BSSID
+ *		matches one of the 4 BSSID registers. Only set when
+ *		first_msdu is set.
+ *
+ * peer_idx_invalid
+ *		Indicates no matching entries within the the max search
+ *		count.  Only set when first_msdu is set.
+ *
+ * peer_idx_timeout
+ *		Indicates an unsuccessful search for the peer index due to
+ *		timeout.  Only set when first_msdu is set.
+ *
+ * power_mgmt
+ *		Power management bit set in the 802.11 header.  Only set
+ *		when first_msdu is set.
+ *
+ * non_qos
+ *		Set if packet is not a non-QoS data frame.  Only set when
+ *		first_msdu is set.
+ *
+ * null_data
+ *		Set if frame type indicates either null data or QoS null
+ *		data format.  Only set when first_msdu is set.
+ *
+ * mgmt_type
+ *		Set if packet is a management packet.  Only set when
+ *		first_msdu is set.
+ *
+ * ctrl_type
+ *		Set if packet is a control packet.  Only set when first_msdu
+ *		is set.
+ *
+ * more_data
+ *		Set if more bit in frame control is set.  Only set when
+ *		first_msdu is set.
+ *
+ * eosp
+ *		Set if the EOSP (end of service period) bit in the QoS
+ *		control field is set.  Only set when first_msdu is set.
+ *
+ * u_apsd_trigger
+ *		Set if packet is U-APSD trigger.  Key table will have bits
+ *		per TID to indicate U-APSD trigger.
+ *
+ * fragment
+ *		Indicates that this is an 802.11 fragment frame.  This is
+ *		set when either the more_frag bit is set in the frame
+ *		control or the fragment number is not zero.  Only set when
+ *		first_msdu is set.
+ *
+ * order
+ *		Set if the order bit in the frame control is set.  Only set
+ *		when first_msdu is set.
+ *
+ * classification
+ *		Indicates that this status has a corresponding MSDU that
+ *		requires FW processing.  The OLE will have classification
+ *		ring mask registers which will indicate the ring(s) for
+ *		packets and descriptors which need FW attention.
+ *
+ * overflow_err
+ *		PCU Receive FIFO does not have enough space to store the
+ *		full receive packet.  Enough space is reserved in the
+ *		receive FIFO for the status is written.  This MPDU remaining
+ *		packets in the PPDU will be filtered and no Ack response
+ *		will be transmitted.
+ *
+ * msdu_length_err
+ *		Indicates that the MSDU length from the 802.3 encapsulated
+ *		length field extends beyond the MPDU boundary.
+ *
+ * tcp_udp_chksum_fail
+ *		Indicates that the computed checksum (tcp_udp_chksum) did
+ *		not match the checksum in the TCP/UDP header.
+ *
+ * ip_chksum_fail
+ *		Indicates that the computed checksum did not match the
+ *		checksum in the IP header.
+ *
+ * sa_idx_invalid
+ *		Indicates no matching entry was found in the address search
+ *		table for the source MAC address.
+ *
+ * da_idx_invalid
+ *		Indicates no matching entry was found in the address search
+ *		table for the destination MAC address.
+ *
+ * sa_idx_timeout
+ *		Indicates an unsuccessful search for the source MAC address
+ *		due to the expiring of the search timer.
+ *
+ * da_idx_timeout
+ *		Indicates an unsuccessful search for the destination MAC
+ *		address due to the expiring of the search timer.
+ *
+ * encrypt_required
+ *		Indicates that this data type frame is not encrypted even if
+ *		the policy for this MPDU requires encryption as indicated in
+ *		the peer table key type.
+ *
+ * directed
+ *		MPDU is a directed packet which means that the RA matched
+ *		our STA addresses.  In proxySTA it means that the TA matched
+ *		an entry in our address search table with the corresponding
+ *		'no_ack' bit is the address search entry cleared.
+ *
+ * buffer_fragment
+ *		Indicates that at least one of the rx buffers has been
+ *		fragmented.  If set the FW should look at the rx_frag_info
+ *		descriptor described below.
+ *
+ * mpdu_length_err
+ *		Indicates that the MPDU was pre-maturely terminated
+ *		resulting in a truncated MPDU.  Don't trust the MPDU length
+ *		field.
+ *
+ * tkip_mic_err
+ *		Indicates that the MPDU Michael integrity check failed
+ *
+ * decrypt_err
+ *		Indicates that the MPDU decrypt integrity check failed
+ *
+ * fcs_err
+ *		Indicates that the MPDU FCS check failed
+ *
+ * msdu_done
+ *		If set indicates that the RX packet data, RX header data, RX
+ *		PPDU start descriptor, RX MPDU start/end descriptor, RX MSDU
+ *		start/end descriptors and RX Attention descriptor are all
+ *		valid.  This bit must be in the last octet of the
+ *		descriptor.
+ */
 
 struct rx_frag_info {
 	u8 ring0_more_count;
@@ -213,22 +213,22 @@ struct rx_frag_info {
 } __packed;
 
 /*
-ring0_more_count
-		Indicates the number of more buffers associated with RX DMA
-		ring 0.  Field is filled in by the RX_DMA.
-
-ring1_more_count
-		Indicates the number of more buffers associated with RX DMA
-		ring 1. Field is filled in by the RX_DMA.
-
-ring2_more_count
-		Indicates the number of more buffers associated with RX DMA
-		ring 2. Field is filled in by the RX_DMA.
-
-ring3_more_count
-		Indicates the number of more buffers associated with RX DMA
-		ring 3. Field is filled in by the RX_DMA.
-*/
+ * ring0_more_count
+ *		Indicates the number of more buffers associated with RX DMA
+ *		ring 0.  Field is filled in by the RX_DMA.
+ *
+ * ring1_more_count
+ *		Indicates the number of more buffers associated with RX DMA
+ *		ring 1. Field is filled in by the RX_DMA.
+ *
+ * ring2_more_count
+ *		Indicates the number of more buffers associated with RX DMA
+ *		ring 2. Field is filled in by the RX_DMA.
+ *
+ * ring3_more_count
+ *		Indicates the number of more buffers associated with RX DMA
+ *		ring 3. Field is filled in by the RX_DMA.
+ */
 
 enum htt_rx_mpdu_encrypt_type {
 	HTT_RX_MPDU_ENCRYPT_WEP40            = 0,
@@ -271,80 +271,80 @@ struct rx_mpdu_start {
 } __packed;
 
 /*
-peer_idx
-		The index of the address search table which associated with
-		the peer table entry corresponding to this MPDU.  Only valid
-		when first_msdu is set.
-
-fr_ds
-		Set if the from DS bit is set in the frame control.  Only
-		valid when first_msdu is set.
-
-to_ds
-		Set if the to DS bit is set in the frame control.  Only
-		valid when first_msdu is set.
-
-encrypted
-		Protected bit from the frame control.  Only valid when
-		first_msdu is set.
-
-retry
-		Retry bit from the frame control.  Only valid when
-		first_msdu is set.
-
-txbf_h_info
-		The MPDU data will contain H information.  Primarily used
-		for debug.
-
-seq_num
-		The sequence number from the 802.11 header.  Only valid when
-		first_msdu is set.
-
-encrypt_type
-		Indicates type of decrypt cipher used (as defined in the
-		peer table)
-		0: WEP40
-		1: WEP104
-		2: TKIP without MIC
-		3: WEP128
-		4: TKIP (WPA)
-		5: WAPI
-		6: AES-CCM (WPA2)
-		7: No cipher
-		Only valid when first_msdu_is set
-
-pn_31_0
-		Bits [31:0] of the PN number extracted from the IV field
-		WEP: IV = {key_id_octet, pn2, pn1, pn0}.  Only pn[23:0] is
-		valid.
-		TKIP: IV = {pn5, pn4, pn3, pn2, key_id_octet, pn0,
-		WEPSeed[1], pn1}.  Only pn[47:0] is valid.
-		AES-CCM: IV = {pn5, pn4, pn3, pn2, key_id_octet, 0x0, pn1,
-		pn0}.  Only pn[47:0] is valid.
-		WAPI: IV = {key_id_octet, 0x0, pn15, pn14, pn13, pn12, pn11,
-		pn10, pn9, pn8, pn7, pn6, pn5, pn4, pn3, pn2, pn1, pn0}.
-		The ext_wapi_pn[127:48] in the rx_msdu_misc descriptor and
-		pn[47:0] are valid.
-		Only valid when first_msdu is set.
-
-pn_47_32
-		Bits [47:32] of the PN number.   See description for
-		pn_31_0.  The remaining PN fields are in the rx_msdu_end
-		descriptor
-
-pn
-		Use this field to access the pn without worrying about
-		byte-order and bitmasking/bitshifting.
-
-directed
-		See definition in RX attention descriptor
-
-reserved_2
-		Reserved: HW should fill with zero.  FW should ignore.
-
-tid
-		The TID field in the QoS control field
-*/
+ * peer_idx
+ *		The index of the address search table which associated with
+ *		the peer table entry corresponding to this MPDU.  Only valid
+ *		when first_msdu is set.
+ *
+ * fr_ds
+ *		Set if the from DS bit is set in the frame control.  Only
+ *		valid when first_msdu is set.
+ *
+ * to_ds
+ *		Set if the to DS bit is set in the frame control.  Only
+ *		valid when first_msdu is set.
+ *
+ * encrypted
+ *		Protected bit from the frame control.  Only valid when
+ *		first_msdu is set.
+ *
+ * retry
+ *		Retry bit from the frame control.  Only valid when
+ *		first_msdu is set.
+ *
+ * txbf_h_info
+ *		The MPDU data will contain H information.  Primarily used
+ *		for debug.
+ *
+ * seq_num
+ *		The sequence number from the 802.11 header.  Only valid when
+ *		first_msdu is set.
+ *
+ * encrypt_type
+ *		Indicates type of decrypt cipher used (as defined in the
+ *		peer table)
+ *		0: WEP40
+ *		1: WEP104
+ *		2: TKIP without MIC
+ *		3: WEP128
+ *		4: TKIP (WPA)
+ *		5: WAPI
+ *		6: AES-CCM (WPA2)
+ *		7: No cipher
+ *		Only valid when first_msdu_is set
+ *
+ * pn_31_0
+ *		Bits [31:0] of the PN number extracted from the IV field
+ *		WEP: IV = {key_id_octet, pn2, pn1, pn0}.  Only pn[23:0] is
+ *		valid.
+ *		TKIP: IV = {pn5, pn4, pn3, pn2, key_id_octet, pn0,
+ *		WEPSeed[1], pn1}.  Only pn[47:0] is valid.
+ *		AES-CCM: IV = {pn5, pn4, pn3, pn2, key_id_octet, 0x0, pn1,
+ *		pn0}.  Only pn[47:0] is valid.
+ *		WAPI: IV = {key_id_octet, 0x0, pn15, pn14, pn13, pn12, pn11,
+ *		pn10, pn9, pn8, pn7, pn6, pn5, pn4, pn3, pn2, pn1, pn0}.
+ *		The ext_wapi_pn[127:48] in the rx_msdu_misc descriptor and
+ *		pn[47:0] are valid.
+ *		Only valid when first_msdu is set.
+ *
+ * pn_47_32
+ *		Bits [47:32] of the PN number.   See description for
+ *		pn_31_0.  The remaining PN fields are in the rx_msdu_end
+ *		descriptor
+ *
+ * pn
+ *		Use this field to access the pn without worrying about
+ *		byte-order and bitmasking/bitshifting.
+ *
+ * directed
+ *		See definition in RX attention descriptor
+ *
+ * reserved_2
+ *		Reserved: HW should fill with zero.  FW should ignore.
+ *
+ * tid
+ *		The TID field in the QoS control field
+ */
 
 #define RX_MPDU_END_INFO0_RESERVED_0_MASK     0x00001fff
 #define RX_MPDU_END_INFO0_RESERVED_0_LSB      0
@@ -363,42 +363,42 @@ struct rx_mpdu_end {
 } __packed;
 
 /*
-reserved_0
-		Reserved
-
-overflow_err
-		PCU Receive FIFO does not have enough space to store the
-		full receive packet.  Enough space is reserved in the
-		receive FIFO for the status is written.  This MPDU remaining
-		packets in the PPDU will be filtered and no Ack response
-		will be transmitted.
-
-last_mpdu
-		Indicates that this is the last MPDU of a PPDU.
-
-post_delim_err
-		Indicates that a delimiter FCS error occurred after this
-		MPDU before the next MPDU.  Only valid when last_msdu is
-		set.
-
-post_delim_cnt
-		Count of the delimiters after this MPDU.  This requires the
-		last MPDU to be held until all the EOF descriptors have been
-		received.  This may be inefficient in the future when
-		ML-MIMO is used.  Only valid when last_mpdu is set.
-
-mpdu_length_err
-		See definition in RX attention descriptor
-
-tkip_mic_err
-		See definition in RX attention descriptor
-
-decrypt_err
-		See definition in RX attention descriptor
-
-fcs_err
-		See definition in RX attention descriptor
-*/
+ * reserved_0
+ *		Reserved
+ *
+ * overflow_err
+ *		PCU Receive FIFO does not have enough space to store the
+ *		full receive packet.  Enough space is reserved in the
+ *		receive FIFO for the status is written.  This MPDU remaining
+ *		packets in the PPDU will be filtered and no Ack response
+ *		will be transmitted.
+ *
+ * last_mpdu
+ *		Indicates that this is the last MPDU of a PPDU.
+ *
+ * post_delim_err
+ *		Indicates that a delimiter FCS error occurred after this
+ *		MPDU before the next MPDU.  Only valid when last_msdu is
+ *		set.
+ *
+ * post_delim_cnt
+ *		Count of the delimiters after this MPDU.  This requires the
+ *		last MPDU to be held until all the EOF descriptors have been
+ *		received.  This may be inefficient in the future when
+ *		ML-MIMO is used.  Only valid when last_mpdu is set.
+ *
+ * mpdu_length_err
+ *		See definition in RX attention descriptor
+ *
+ * tkip_mic_err
+ *		See definition in RX attention descriptor
+ *
+ * decrypt_err
+ *		See definition in RX attention descriptor
+ *
+ * fcs_err
+ *		See definition in RX attention descriptor
+ */
 
 #define RX_MSDU_START_INFO0_MSDU_LENGTH_MASK    0x00003fff
 #define RX_MSDU_START_INFO0_MSDU_LENGTH_LSB     0
@@ -436,82 +436,82 @@ struct rx_msdu_start {
 } __packed;
 
 /*
-msdu_length
-		MSDU length in bytes after decapsulation.  This field is
-		still valid for MPDU frames without A-MSDU.  It still
-		represents MSDU length after decapsulation
-
-ip_offset
-		Indicates the IP offset in bytes from the start of the
-		packet after decapsulation.  Only valid if ipv4_proto or
-		ipv6_proto is set.
-
-ring_mask
-		Indicates the destination RX rings for this MSDU.
-
-tcp_udp_offset
-		Indicates the offset in bytes to the start of TCP or UDP
-		header from the start of the IP header after decapsulation.
-		Only valid if tcp_prot or udp_prot is set.  The value 0
-		indicates that the offset is longer than 127 bytes.
-
-reserved_0c
-		Reserved: HW should fill with zero.  FW should ignore.
-
-flow_id_crc
-		The flow_id_crc runs CRC32 on the following information:
-		IPv4 option: dest_addr[31:0], src_addr [31:0], {24'b0,
-		protocol[7:0]}.
-		IPv6 option: dest_addr[127:0], src_addr [127:0], {24'b0,
-		next_header[7:0]}
-		UDP case: sort_port[15:0], dest_port[15:0]
-		TCP case: sort_port[15:0], dest_port[15:0],
-		{header_length[3:0], 6'b0, flags[5:0], window_size[15:0]},
-		{16'b0, urgent_ptr[15:0]}, all options except 32-bit
-		timestamp.
-
-msdu_number
-		Indicates the MSDU number within a MPDU.  This value is
-		reset to zero at the start of each MPDU.  If the number of
-		MSDU exceeds 255 this number will wrap using modulo 256.
-
-decap_format
-		Indicates the format after decapsulation:
-		0: RAW: No decapsulation
-		1: Native WiFi
-		2: Ethernet 2 (DIX)
-		3: 802.3 (SNAP/LLC)
-
-ipv4_proto
-		Set if L2 layer indicates IPv4 protocol.
-
-ipv6_proto
-		Set if L2 layer indicates IPv6 protocol.
-
-tcp_proto
-		Set if the ipv4_proto or ipv6_proto are set and the IP
-		protocol indicates TCP.
-
-udp_proto
-		Set if the ipv4_proto or ipv6_proto are set and the IP
-			protocol indicates UDP.
-
-ip_frag
-		Indicates that either the IP More frag bit is set or IP frag
-		number is non-zero.  If set indicates that this is a
-		fragmented IP packet.
-
-tcp_only_ack
-		Set if only the TCP Ack bit is set in the TCP flags and if
-		the TCP payload is 0.
-
-sa_idx
-		The offset in the address table which matches the MAC source
-		address.
-
-reserved_2b
-		Reserved: HW should fill with zero.  FW should ignore.
-*/
+ * msdu_length
+ *		MSDU length in bytes after decapsulation.  This field is
+ *		still valid for MPDU frames without A-MSDU.  It still
+ *		represents MSDU length after decapsulation
+ *
+ * ip_offset
+ *		Indicates the IP offset in bytes from the start of the
+ *		packet after decapsulation.  Only valid if ipv4_proto or
+ *		ipv6_proto is set.
+ *
+ * ring_mask
+ *		Indicates the destination RX rings for this MSDU.
+ *
+ * tcp_udp_offset
+ *		Indicates the offset in bytes to the start of TCP or UDP
+ *		header from the start of the IP header after decapsulation.
+ *		Only valid if tcp_prot or udp_prot is set.  The value 0
+ *		indicates that the offset is longer than 127 bytes.
+ *
+ * reserved_0c
+ *		Reserved: HW should fill with zero.  FW should ignore.
+ *
+ * flow_id_crc
+ *		The flow_id_crc runs CRC32 on the following information:
+ *		IPv4 option: dest_addr[31:0], src_addr [31:0], {24'b0,
+ *		protocol[7:0]}.
+ *		IPv6 option: dest_addr[127:0], src_addr [127:0], {24'b0,
+ *		next_header[7:0]}
+ *		UDP case: sort_port[15:0], dest_port[15:0]
+ *		TCP case: sort_port[15:0], dest_port[15:0],
+ *		{header_length[3:0], 6'b0, flags[5:0], window_size[15:0]},
+ *		{16'b0, urgent_ptr[15:0]}, all options except 32-bit
+ *		timestamp.
+ *
+ * msdu_number
+ *		Indicates the MSDU number within a MPDU.  This value is
+ *		reset to zero at the start of each MPDU.  If the number of
+ *		MSDU exceeds 255 this number will wrap using modulo 256.
+ *
+ * decap_format
+ *		Indicates the format after decapsulation:
+ *		0: RAW: No decapsulation
+ *		1: Native WiFi
+ *		2: Ethernet 2 (DIX)
+ *		3: 802.3 (SNAP/LLC)
+ *
+ * ipv4_proto
+ *		Set if L2 layer indicates IPv4 protocol.
+ *
+ * ipv6_proto
+ *		Set if L2 layer indicates IPv6 protocol.
+ *
+ * tcp_proto
+ *		Set if the ipv4_proto or ipv6_proto are set and the IP
+ *		protocol indicates TCP.
+ *
+ * udp_proto
+ *		Set if the ipv4_proto or ipv6_proto are set and the IP
+ *			protocol indicates UDP.
+ *
+ * ip_frag
+ *		Indicates that either the IP More frag bit is set or IP frag
+ *		number is non-zero.  If set indicates that this is a
+ *		fragmented IP packet.
+ *
+ * tcp_only_ack
+ *		Set if only the TCP Ack bit is set in the TCP flags and if
+ *		the TCP payload is 0.
+ *
+ * sa_idx
+ *		The offset in the address table which matches the MAC source
+ *		address.
+ *
+ * reserved_2b
+ *		Reserved: HW should fill with zero.  FW should ignore.
+ */
 
 #define RX_MSDU_END_INFO0_REPORTED_MPDU_LENGTH_MASK 0x00003fff
 #define RX_MSDU_END_INFO0_REPORTED_MPDU_LENGTH_LSB  0
@@ -530,64 +530,64 @@ struct rx_msdu_end {
 } __packed;
 
 /*
-ip_hdr_chksum
-		This can include the IP header checksum or the pseudo header
-		checksum used by TCP/UDP checksum.
-
-tcp_udp_chksum
-		The value of the computed TCP/UDP checksum.  A mode bit
-		selects whether this checksum is the full checksum or the
-		partial checksum which does not include the pseudo header.
-
-key_id_octet
-		The key ID octet from the IV.  Only valid when first_msdu is
-		set.
-
-classification_filter
-		Indicates the number classification filter rule
-
-ext_wapi_pn_63_48
-		Extension PN (packet number) which is only used by WAPI.
-		This corresponds to WAPI PN bits [63:48] (pn6 and pn7).  The
-		WAPI PN bits [63:0] are in the pn field of the rx_mpdu_start
-		descriptor.
-
-ext_wapi_pn_95_64
-		Extension PN (packet number) which is only used by WAPI.
-		This corresponds to WAPI PN bits [95:64] (pn8, pn9, pn10 and
-		pn11).
-
-ext_wapi_pn_127_96
-		Extension PN (packet number) which is only used by WAPI.
-		This corresponds to WAPI PN bits [127:96] (pn12, pn13, pn14,
-		pn15).
-
-reported_mpdu_length
-		MPDU length before decapsulation.  Only valid when
-		first_msdu is set.  This field is taken directly from the
-		length field of the A-MPDU delimiter or the preamble length
-		field for non-A-MPDU frames.
-
-first_msdu
-		Indicates the first MSDU of A-MSDU.  If both first_msdu and
-		last_msdu are set in the MSDU then this is a non-aggregated
-		MSDU frame: normal MPDU.  Interior MSDU in an A-MSDU shall
-		have both first_mpdu and last_mpdu bits set to 0.
-
-last_msdu
-		Indicates the last MSDU of the A-MSDU.  MPDU end status is
-		only valid when last_msdu is set.
-
-reserved_3a
-		Reserved: HW should fill with zero.  FW should ignore.
-
-pre_delim_err
-		Indicates that the first delimiter had a FCS failure.  Only
-		valid when first_mpdu and first_msdu are set.
-
-reserved_3b
-		Reserved: HW should fill with zero.  FW should ignore.
-*/
+ *ip_hdr_chksum
+ *		This can include the IP header checksum or the pseudo header
+ *		checksum used by TCP/UDP checksum.
+ *
+ *tcp_udp_chksum
+ *		The value of the computed TCP/UDP checksum.  A mode bit
+ *		selects whether this checksum is the full checksum or the
+ *		partial checksum which does not include the pseudo header.
+ *
+ *key_id_octet
+ *		The key ID octet from the IV.  Only valid when first_msdu is
+ *		set.
+ *
+ *classification_filter
+ *		Indicates the number classification filter rule
+ *
+ *ext_wapi_pn_63_48
+ *		Extension PN (packet number) which is only used by WAPI.
+ *		This corresponds to WAPI PN bits [63:48] (pn6 and pn7).  The
+ *		WAPI PN bits [63:0] are in the pn field of the rx_mpdu_start
+ *		descriptor.
+ *
+ *ext_wapi_pn_95_64
+ *		Extension PN (packet number) which is only used by WAPI.
+ *		This corresponds to WAPI PN bits [95:64] (pn8, pn9, pn10 and
+ *		pn11).
+ *
+ *ext_wapi_pn_127_96
+ *		Extension PN (packet number) which is only used by WAPI.
+ *		This corresponds to WAPI PN bits [127:96] (pn12, pn13, pn14,
+ *		pn15).
+ *
+ *reported_mpdu_length
+ *		MPDU length before decapsulation.  Only valid when
+ *		first_msdu is set.  This field is taken directly from the
+ *		length field of the A-MPDU delimiter or the preamble length
+ *		field for non-A-MPDU frames.
+ *
+ *first_msdu
+ *		Indicates the first MSDU of A-MSDU.  If both first_msdu and
+ *		last_msdu are set in the MSDU then this is a non-aggregated
+ *		MSDU frame: normal MPDU.  Interior MSDU in an A-MSDU shall
+ *		have both first_mpdu and last_mpdu bits set to 0.
+ *
+ *last_msdu
+ *		Indicates the last MSDU of the A-MSDU.  MPDU end status is
+ *		only valid when last_msdu is set.
+ *
+ *reserved_3a
+ *		Reserved: HW should fill with zero.  FW should ignore.
+ *
+ *pre_delim_err
+ *		Indicates that the first delimiter had a FCS failure.  Only
+ *		valid when first_mpdu and first_msdu are set.
+ *
+ *reserved_3b
+ *		Reserved: HW should fill with zero.  FW should ignore.
+ */
 
 #define RX_PPDU_START_SIG_RATE_SELECT_OFDM 0
 #define RX_PPDU_START_SIG_RATE_SELECT_CCK  1
@@ -659,164 +659,164 @@ struct rx_ppdu_start {
 } __packed;
 
 /*
-rssi_chain0_pri20
-		RSSI of RX PPDU on chain 0 of primary 20 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain0_sec20
-		RSSI of RX PPDU on chain 0 of secondary 20 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain0_sec40
-		RSSI of RX PPDU on chain 0 of secondary 40 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain0_sec80
-		RSSI of RX PPDU on chain 0 of secondary 80 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain1_pri20
-		RSSI of RX PPDU on chain 1 of primary 20 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain1_sec20
-		RSSI of RX PPDU on chain 1 of secondary 20 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain1_sec40
-		RSSI of RX PPDU on chain 1 of secondary 40 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain1_sec80
-		RSSI of RX PPDU on chain 1 of secondary 80 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain2_pri20
-		RSSI of RX PPDU on chain 2 of primary 20 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain2_sec20
-		RSSI of RX PPDU on chain 2 of secondary 20 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain2_sec40
-		RSSI of RX PPDU on chain 2 of secondary 40 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain2_sec80
-		RSSI of RX PPDU on chain 2 of secondary 80 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain3_pri20
-		RSSI of RX PPDU on chain 3 of primary 20 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain3_sec20
-		RSSI of RX PPDU on chain 3 of secondary 20 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain3_sec40
-		RSSI of RX PPDU on chain 3 of secondary 40 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_chain3_sec80
-		RSSI of RX PPDU on chain 3 of secondary 80 MHz bandwidth.
-		Value of 0x80 indicates invalid.
-
-rssi_comb
-		The combined RSSI of RX PPDU of all active chains and
-		bandwidths.  Value of 0x80 indicates invalid.
-
-reserved_4a
-		Reserved: HW should fill with 0, FW should ignore.
-
-is_greenfield
-		Do we really support this?
-
-reserved_4b
-		Reserved: HW should fill with 0, FW should ignore.
-
-l_sig_rate
-		If l_sig_rate_select is 0:
-		0x8: OFDM 48 Mbps
-		0x9: OFDM 24 Mbps
-		0xA: OFDM 12 Mbps
-		0xB: OFDM 6 Mbps
-		0xC: OFDM 54 Mbps
-		0xD: OFDM 36 Mbps
-		0xE: OFDM 18 Mbps
-		0xF: OFDM 9 Mbps
-		If l_sig_rate_select is 1:
-		0x8: CCK 11 Mbps long preamble
-		0x9: CCK 5.5 Mbps long preamble
-		0xA: CCK 2 Mbps long preamble
-		0xB: CCK 1 Mbps long preamble
-		0xC: CCK 11 Mbps short preamble
-		0xD: CCK 5.5 Mbps short preamble
-		0xE: CCK 2 Mbps short preamble
-
-l_sig_rate_select
-		Legacy signal rate select.  If set then l_sig_rate indicates
-		CCK rates.  If clear then l_sig_rate indicates OFDM rates.
-
-l_sig_length
-		Length of legacy frame in octets.
-
-l_sig_parity
-		Odd parity over l_sig_rate and l_sig_length
-
-l_sig_tail
-		Tail bits for Viterbi decoder
-
-preamble_type
-		Indicates the type of preamble ahead:
-		0x4: Legacy (OFDM/CCK)
-		0x8: HT
-		0x9: HT with TxBF
-		0xC: VHT
-		0xD: VHT with TxBF
-		0x80 - 0xFF: Reserved for special baseband data types such
-		as radar and spectral scan.
-
-ht_sig_vht_sig_a_1
-		If preamble_type == 0x8 or 0x9
-		HT-SIG (first 24 bits)
-		If preamble_type == 0xC or 0xD
-		VHT-SIG A (first 24 bits)
-		Else
-		Reserved
-
-reserved_6
-		Reserved: HW should fill with 0, FW should ignore.
-
-ht_sig_vht_sig_a_2
-		If preamble_type == 0x8 or 0x9
-		HT-SIG (last 24 bits)
-		If preamble_type == 0xC or 0xD
-		VHT-SIG A (last 24 bits)
-		Else
-		Reserved
-
-txbf_h_info
-		Indicates that the packet data carries H information which
-		is used for TxBF debug.
-
-reserved_7
-		Reserved: HW should fill with 0, FW should ignore.
-
-vht_sig_b
-		WiFi 1.0 and WiFi 2.0 will likely have this field to be all
-		0s since the BB does not plan on decoding VHT SIG-B.
-
-reserved_8
-		Reserved: HW should fill with 0, FW should ignore.
-
-service
-		Service field from BB for OFDM, HT and VHT packets.  CCK
-		packets will have service field of 0.
-
-reserved_9
-		Reserved: HW should fill with 0, FW should ignore.
+ * rssi_chain0_pri20
+ *		RSSI of RX PPDU on chain 0 of primary 20 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain0_sec20
+ *		RSSI of RX PPDU on chain 0 of secondary 20 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain0_sec40
+ *		RSSI of RX PPDU on chain 0 of secondary 40 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain0_sec80
+ *		RSSI of RX PPDU on chain 0 of secondary 80 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain1_pri20
+ *		RSSI of RX PPDU on chain 1 of primary 20 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain1_sec20
+ *		RSSI of RX PPDU on chain 1 of secondary 20 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain1_sec40
+ *		RSSI of RX PPDU on chain 1 of secondary 40 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain1_sec80
+ *		RSSI of RX PPDU on chain 1 of secondary 80 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain2_pri20
+ *		RSSI of RX PPDU on chain 2 of primary 20 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain2_sec20
+ *		RSSI of RX PPDU on chain 2 of secondary 20 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain2_sec40
+ *		RSSI of RX PPDU on chain 2 of secondary 40 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain2_sec80
+ *		RSSI of RX PPDU on chain 2 of secondary 80 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain3_pri20
+ *		RSSI of RX PPDU on chain 3 of primary 20 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain3_sec20
+ *		RSSI of RX PPDU on chain 3 of secondary 20 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain3_sec40
+ *		RSSI of RX PPDU on chain 3 of secondary 40 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_chain3_sec80
+ *		RSSI of RX PPDU on chain 3 of secondary 80 MHz bandwidth.
+ *		Value of 0x80 indicates invalid.
+ *
+ * rssi_comb
+ *		The combined RSSI of RX PPDU of all active chains and
+ *		bandwidths.  Value of 0x80 indicates invalid.
+ *
+ * reserved_4a
+ *		Reserved: HW should fill with 0, FW should ignore.
+ *
+ * is_greenfield
+ *		Do we really support this?
+ *
+ * reserved_4b
+ *		Reserved: HW should fill with 0, FW should ignore.
+ *
+ * l_sig_rate
+ *		If l_sig_rate_select is 0:
+ *		0x8: OFDM 48 Mbps
+ *		0x9: OFDM 24 Mbps
+ *		0xA: OFDM 12 Mbps
+ *		0xB: OFDM 6 Mbps
+ *		0xC: OFDM 54 Mbps
+ *		0xD: OFDM 36 Mbps
+ *		0xE: OFDM 18 Mbps
+ *		0xF: OFDM 9 Mbps
+ *		If l_sig_rate_select is 1:
+ *		0x8: CCK 11 Mbps long preamble
+ *		0x9: CCK 5.5 Mbps long preamble
+ *		0xA: CCK 2 Mbps long preamble
+ *		0xB: CCK 1 Mbps long preamble
+ *		0xC: CCK 11 Mbps short preamble
+ *		0xD: CCK 5.5 Mbps short preamble
+ *		0xE: CCK 2 Mbps short preamble
+ *
+ * l_sig_rate_select
+ *		Legacy signal rate select.  If set then l_sig_rate indicates
+ *		CCK rates.  If clear then l_sig_rate indicates OFDM rates.
+ *
+ * l_sig_length
+ *		Length of legacy frame in octets.
+ *
+ * l_sig_parity
+ *		Odd parity over l_sig_rate and l_sig_length
+ *
+ * l_sig_tail
+ *		Tail bits for Viterbi decoder
+ *
+ * preamble_type
+ *		Indicates the type of preamble ahead:
+ *		0x4: Legacy (OFDM/CCK)
+ *		0x8: HT
+ *		0x9: HT with TxBF
+ *		0xC: VHT
+ *		0xD: VHT with TxBF
+ *		0x80 - 0xFF: Reserved for special baseband data types such
+ *		as radar and spectral scan.
+ *
+ * ht_sig_vht_sig_a_1
+ *		If preamble_type == 0x8 or 0x9
+ *		HT-SIG (first 24 bits)
+ *		If preamble_type == 0xC or 0xD
+ *		VHT-SIG A (first 24 bits)
+ *		Else
+ *		Reserved
+ *
+ * reserved_6
+ *		Reserved: HW should fill with 0, FW should ignore.
+ *
+ * ht_sig_vht_sig_a_2
+ *		If preamble_type == 0x8 or 0x9
+ *		HT-SIG (last 24 bits)
+ *		If preamble_type == 0xC or 0xD
+ *		VHT-SIG A (last 24 bits)
+ *		Else
+ *		Reserved
+ *
+ * txbf_h_info
+ *		Indicates that the packet data carries H information which
+ *		is used for TxBF debug.
+ *
+ * reserved_7
+ *		Reserved: HW should fill with 0, FW should ignore.
+ *
+ * vht_sig_b
+ *		WiFi 1.0 and WiFi 2.0 will likely have this field to be all
+ *		0s since the BB does not plan on decoding VHT SIG-B.
+ *
+ * reserved_8
+ *		Reserved: HW should fill with 0, FW should ignore.
+ *
+ * service
+ *		Service field from BB for OFDM, HT and VHT packets.  CCK
+ *		packets will have service field of 0.
+ *
+ * reserved_9
+ *		Reserved: HW should fill with 0, FW should ignore.
 */
 
 
@@ -859,122 +859,122 @@ struct rx_ppdu_end {
 } __packed;
 
 /*
-evm_p0
-		EVM for pilot 0.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p1
-		EVM for pilot 1.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p2
-		EVM for pilot 2.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p3
-		EVM for pilot 3.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p4
-		EVM for pilot 4.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p5
-		EVM for pilot 5.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p6
-		EVM for pilot 6.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p7
-		EVM for pilot 7.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p8
-		EVM for pilot 8.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p9
-		EVM for pilot 9.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p10
-		EVM for pilot 10.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p11
-		EVM for pilot 11.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p12
-		EVM for pilot 12.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p13
-		EVM for pilot 13.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p14
-		EVM for pilot 14.  Contain EVM for streams: 0, 1, 2 and 3.
-
-evm_p15
-		EVM for pilot 15.  Contain EVM for streams: 0, 1, 2 and 3.
-
-tsf_timestamp
-		Receive TSF timestamp sampled on the rising edge of
-		rx_clear.  For PHY errors this may be the current TSF when
-		phy_error is asserted if the rx_clear does not assert before
-		the end of the PHY error.
-
-wb_timestamp
-		WLAN/BT timestamp is a 1 usec resolution timestamp which
-		does not get updated based on receive beacon like TSF.  The
-		same rules for capturing tsf_timestamp are used to capture
-		the wb_timestamp.
-
-locationing_timestamp
-		Timestamp used for locationing.  This timestamp is used to
-		indicate fractions of usec.  For example if the MAC clock is
-		running at 80 MHz, the timestamp will increment every 12.5
-		nsec.  The value starts at 0 and increments to 79 and
-		returns to 0 and repeats.  This information is valid for
-		every PPDU.  This information can be used in conjunction
-		with wb_timestamp to capture large delta times.
-
-phy_err_code
-		See the 1.10.8.1.2 for the list of the PHY error codes.
-
-phy_err
-		Indicates a PHY error was detected for this PPDU.
-
-rx_location
-		Indicates that location information was requested.
-
-txbf_h_info
-		Indicates that the packet data carries H information which
-		is used for TxBF debug.
-
-reserved_18
-		Reserved: HW should fill with 0, FW should ignore.
-
-rx_antenna
-		Receive antenna value
-
-tx_ht_vht_ack
-		Indicates that a HT or VHT Ack/BA frame was transmitted in
-		response to this receive packet.
-
-bb_captured_channel
-		Indicates that the BB has captured a channel dump.  FW can
-		then read the channel dump memory.  This may indicate that
-		the channel was captured either based on PCU setting the
-		capture_channel bit  BB descriptor or FW setting the
-		capture_channel mode bit.
-
-reserved_19
-		Reserved: HW should fill with 0, FW should ignore.
-
-bb_length
-		Indicates the number of bytes of baseband information for
-		PPDUs where the BB descriptor preamble type is 0x80 to 0xFF
-		which indicates that this is not a normal PPDU but rather
-		contains baseband debug information.
-
-reserved_20
-		Reserved: HW should fill with 0, FW should ignore.
-
-ppdu_done
-		PPDU end status is only valid when ppdu_done bit is set.
-		Every time HW sets this bit in memory FW/SW must clear this
-		bit in memory.  FW will initialize all the ppdu_done dword
-		to 0.
+ * evm_p0
+ *		EVM for pilot 0.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p1
+ *		EVM for pilot 1.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p2
+ *		EVM for pilot 2.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p3
+ *		EVM for pilot 3.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p4
+ *		EVM for pilot 4.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p5
+ *		EVM for pilot 5.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p6
+ *		EVM for pilot 6.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p7
+ *		EVM for pilot 7.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p8
+ *		EVM for pilot 8.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p9
+ *		EVM for pilot 9.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p10
+ *		EVM for pilot 10.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p11
+ *		EVM for pilot 11.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p12
+ *		EVM for pilot 12.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p13
+ *		EVM for pilot 13.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p14
+ *		EVM for pilot 14.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * evm_p15
+ *		EVM for pilot 15.  Contain EVM for streams: 0, 1, 2 and 3.
+ *
+ * tsf_timestamp
+ *		Receive TSF timestamp sampled on the rising edge of
+ *		rx_clear.  For PHY errors this may be the current TSF when
+ *		phy_error is asserted if the rx_clear does not assert before
+ *		the end of the PHY error.
+ *
+ * wb_timestamp
+ *		WLAN/BT timestamp is a 1 usec resolution timestamp which
+ *		does not get updated based on receive beacon like TSF.  The
+ *		same rules for capturing tsf_timestamp are used to capture
+ *		the wb_timestamp.
+ *
+ * locationing_timestamp
+ *		Timestamp used for locationing.  This timestamp is used to
+ *		indicate fractions of usec.  For example if the MAC clock is
+ *		running at 80 MHz, the timestamp will increment every 12.5
+ *		nsec.  The value starts at 0 and increments to 79 and
+ *		returns to 0 and repeats.  This information is valid for
+ *		every PPDU.  This information can be used in conjunction
+ *		with wb_timestamp to capture large delta times.
+ *
+ * phy_err_code
+ *		See the 1.10.8.1.2 for the list of the PHY error codes.
+ *
+ * phy_err
+ *		Indicates a PHY error was detected for this PPDU.
+ *
+ * rx_location
+ *		Indicates that location information was requested.
+ *
+ * txbf_h_info
+ *		Indicates that the packet data carries H information which
+ *		is used for TxBF debug.
+ *
+ * reserved_18
+ *		Reserved: HW should fill with 0, FW should ignore.
+ *
+ * rx_antenna
+ *		Receive antenna value
+ *
+ * tx_ht_vht_ack
+ *		Indicates that a HT or VHT Ack/BA frame was transmitted in
+ *		response to this receive packet.
+ *
+ * bb_captured_channel
+ *		Indicates that the BB has captured a channel dump.  FW can
+ *		then read the channel dump memory.  This may indicate that
+ *		the channel was captured either based on PCU setting the
+ *		capture_channel bit  BB descriptor or FW setting the
+ *		capture_channel mode bit.
+ *
+ * reserved_19
+ *		Reserved: HW should fill with 0, FW should ignore.
+ *
+ * bb_length
+ *		Indicates the number of bytes of baseband information for
+ *		PPDUs where the BB descriptor preamble type is 0x80 to 0xFF
+ *		which indicates that this is not a normal PPDU but rather
+ *		contains baseband debug information.
+ *
+ * reserved_20
+ *		Reserved: HW should fill with 0, FW should ignore.
+ *
+ * ppdu_done
+ *		PPDU end status is only valid when ppdu_done bit is set.
+ *		Every time HW sets this bit in memory FW/SW must clear this
+ *		bit in memory.  FW will initialize all the ppdu_done dword
+ *		to 0.
 */
 
 #define FW_RX_DESC_INFO0_DISCARD  (1 << 0)
Signature · 1 line
1.7.10