Skip to contentSkip to conversation

ClearFog Base static variant support

PATCH Superseded Joel Johnson 3 participants 35 messages Jan 27, 2020 – Mar 23, 2020

Subsystems (3)

v5 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

v5 cover ClearFog Base static variant support

This patch series adds support for ClearFog Base static configuration, as well as updating and fixing the ClearFog support for MMC and SPI booting.

v2 changes:
- updated against, and dependent on, https://patchwork.ozlabs.org/cover/1200324
v3 changes:
- rebased against ClearFog runtime TLV EEPROM changes merged into mvebu/master
v4
- adjust static SerDes configuration at runtime instead of #ifdef
v5
- distinguish build-only config changes (SFP and PCIe/SATA) from runtime detectable config changes
- retested SATA mode in PCIe slot with swap rx changes, confirmed working as presently patched. Only tested with ClearFog Base which only provides single channel, but Pro mechanism is parallel.

Joel Johnson (12):
arm: mvebu: fix SerDes table alignment
arm: mvebu: solidrun: remove hardcoded DTS MAC address
arm: mvebu: clearfog: use Pro name by default
arm: mvebu: clearfog: initial ClearFog Base variant
arm: mvebu: clearfog: Add option for 2.5 Gbps SFP
arm: mvebu: clearfog: Add SATA mode flags
arm: mvebu: clearfog: Unify DT selection paths
arm: mvebu: clearfog: add SPI offsets
arm: mvebu: enable working default boot support
arm: mvebu: clearfog: move ENV params to Kconfig
arm: mvebu: clearfog: don't always use SPL MMC
arm: mvebu: clearfog: Use Pro DT by default

 .../arm/dts/armada-38x-solidrun-microsom.dtsi |  1 -
 arch/arm/mach-mvebu/Kconfig                   | 13 ++++
 .../serdes/a38x/high_speed_env_spec.c         |  6 +-
 board/solidrun/clearfog/Kconfig               | 62 +++++++++++++++++++
 board/solidrun/clearfog/clearfog.c            | 53 +++++++++++++---
 configs/clearfog_defconfig                    |  4 --
 include/configs/clearfog.h                    |  1 -
 7 files changed, 124 insertions(+), 16 deletions(-)
 create mode 100644 board/solidrun/clearfog/Kconfig
Signature · 1 line
2.20.1
#1 lore raw

PATCH v5 1/12 arm: mvebu: fix SerDes table alignment

Tested on Solidrun ClearFog Base. Table alignment was:
| Lane # | Speed | Type |
--------------------------------

 |   0    |  3   |  SATA0       |
 |   1    |  0   |  SGMII1      |
 |   2    |  3   |  SATA1       |
 |   3    |  5   |  USB3 HOST1  |
 |   4    |  5   |  USB3 HOST0  |
 |   5    |  4   |  SGMII2      |

--------------------------------

After the change, it's correctly aligned as:
| Lane # | Speed | Type |
--------------------------------

 |   0    |   3   | SATA0       |
 |   1    |   0   | SGMII1      |
 |   2    |   5   | PCIe1       |
 |   3    |   5   | USB3 HOST1  |
 |   4    |   5   | PCIe2       |
 |   5    |   0   | SGMII2      |

--------------------------------

---

v2 changes
- none
v3 changes
- none
v4 changes
- none
v5 changes
- none

---
 arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c +3 -3
index 33e70569bc..66409a50c0 100644
@@ -1366,16 +1366,16 @@ static void print_topology_details(const struct serdes_map *serdes_map,
 
 	DEBUG_INIT_S("board SerDes lanes topology details:\n");
 
-	DEBUG_INIT_S(" | Lane #  | Speed |  Type       |\n");
+	DEBUG_INIT_S(" | Lane # | Speed |  Type       |\n");
 	DEBUG_INIT_S(" --------------------------------\n");
 	for (lane_num = 0; lane_num < count; lane_num++) {
 		if (serdes_map[lane_num].serdes_type == DEFAULT_SERDES)
 			continue;
 		DEBUG_INIT_S(" |   ");
 		DEBUG_INIT_D(hws_get_physical_serdes_num(lane_num), 1);
-		DEBUG_INIT_S("    |  ");
+		DEBUG_INIT_S("    |   ");
 		DEBUG_INIT_D(serdes_map[lane_num].serdes_speed, 2);
-		DEBUG_INIT_S("   |  ");
+		DEBUG_INIT_S("   | ");
 		DEBUG_INIT_S((char *)
 			     serdes_type_to_string[serdes_map[lane_num].
 						   serdes_type]);
Signature · 1 line
2.20.1
#2 lore raw

PATCH v5 1/12 arm: mvebu: fix SerDes table alignment

Quoted 20 lines · Joel Johnson

Tested on Solidrun ClearFog Base. Table alignment was:
| Lane # | Speed | Type |
--------------------------------

  |   0    |  3   |  SATA0       |
  |   1    |  0   |  SGMII1      |
  |   2    |  3   |  SATA1       |
  |   3    |  5   |  USB3 HOST1  |
  |   4    |  5   |  USB3 HOST0  |
  |   5    |  4   |  SGMII2      |

--------------------------------

After the change, it's correctly aligned as:
| Lane # | Speed | Type |
--------------------------------

  |   0    |   3   | SATA0       |
  |   1    |   0   | SGMII1      |
  |   2    |   5   | PCIe1       |
  |   3    |   5   | USB3 HOST1  |
  |   4    |   5   | PCIe2       |
  |   5    |   0   | SGMII2      |
Quoted 3 lines

--------------------------------

Thanks,
Stefan

#3 lore raw

PATCH v5 2/12 arm: mvebu: solidrun: remove hardcoded DTS MAC address

In reply to Joel Johnson

Using a consistent hardcoded MAC address from the DTS file causes issues when using multiple devices on the same network segment. Instead rely on environment configuration or random generation.

---

v2 changes:
- none
v3 changes:
- none
v4 changes:
- none
v5 changes:
- none

---
 arch/arm/dts/armada-38x-solidrun-microsom.dtsi | 1 -
 1 file changed, 1 deletion(-)
arch/arm/dts/armada-38x-solidrun-microsom.dtsi +0 -1
index a322a28c21..9bbeafc53b 100644
@@ -39,7 +39,6 @@
 
 &eth0 {
 	/* ethernet at 70000 */
-	mac-address = [00 50 43 02 02 01];
 	pinctrl-0 = <&ge0_rgmii_pins>;
 	pinctrl-names = "default";
 	phy = <&phy_dedicated>;
Signature · 1 line
2.20.1
#4 lore raw

PATCH v5 2/12 arm: mvebu: solidrun: remove hardcoded DTS MAC address

Quoted 5 lines · Joel Johnson

Using a consistent hardcoded MAC address from the DTS file causes issues when using multiple devices on the same network segment. Instead rely on environment configuration or random generation.

Thanks,
Stefan

#5 lore raw

PATCH v5 3/12 arm: mvebu: clearfog: use Pro name by default

In reply to Joel Johnson

Make the board version printed indicate the Pro variant default. Also adjust static name casing to match what is expected for EEPROM product name to share string constants.

---

v4 changes:
- newly added
v5 changes:
- none

---
 board/solidrun/clearfog/clearfog.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
board/solidrun/clearfog/clearfog.c +1 -1
index e268ef55a2..9b31902c70 100644
@@ -170,7 +170,7 @@ int board_init(void)
 
 int checkboard(void)
 {
-	char *board = "ClearFog";
+	char *board = "Clearfog Pro";
 
 	cf_read_tlv_data();
 	if (strlen(cf_tlv_data.tlv_product_name[0]) > 0)
Signature · 1 line
2.20.1
#6 lore raw

PATCH v5 3/12 arm: mvebu: clearfog: use Pro name by default

Quoted 4 lines · Joel Johnson

Make the board version printed indicate the Pro variant default. Also adjust static name casing to match what is expected for EEPROM product name to share string constants.

Quoted 8 lines

---

v4 changes:
- newly added
v5 changes:
- none

Please make sure put your S-o-b line above the first "---" line next time.

Thanks,
Stefan

#7 lore raw

PATCH v5 4/12 arm: mvebu: clearfog: initial ClearFog Base variant

In reply to Joel Johnson

Add a unique entry for ClearFog Base variant, reflected in the board name and adjusted SerDes topology.

---

v2 changes:
- reworked based on Baruch's run-time TLV EEPROM detection series
v3 changes:
- rebased on mvebu merged run-time TLV EEPROM detection series
- minor update to help test regarding runtime detection failures
v4 changes:
- use runtime static config adjust instead of #ifdef in cases where hardware EEPROM detection fails or is disabled in build
SPL size change for defconfig increases 36 bytes (122893 to 122929) SPL size change for defconfig+Base increases 60 bytes (122893 to 122953)
- add placeholder support for EEPROM based Clearfog Pro, based on initial name confirmation from Baruch. I wanted to include the check at least in the patch for review to indicate expected usage to ensure that a Clearfog Pro EEPROM device boots correctly even if the image is built with Base static configuration. If there are other prerelease concerns and this should be added separately later, I'd be fine with that too.
- Note that this approach *does not* currently provide any mechanism for EEPROM detected boards to have their SFP speed changed or switch between PCIE/SATA signalling. I'm assuming that will be done based on hardware detection, but confirmation/acceptance in review would be appreciated so it can be revisited if needed.
v5 changes:
- only make Base variant adjustment based on runtime configuration

---
 arch/arm/mach-mvebu/Kconfig        |  2 ++
 board/solidrun/clearfog/Kconfig    | 18 ++++++++++++++++++
 board/solidrun/clearfog/clearfog.c | 29 +++++++++++++++++++++++------
 3 files changed, 43 insertions(+), 6 deletions(-)
 create mode 100644 board/solidrun/clearfog/Kconfig
arch/arm/mach-mvebu/Kconfig +2 -0
index bc5eaa5a76..161dee937f 100644
@@ -280,4 +280,6 @@ config SECURED_MODE_CSK_INDEX
 	default 0
 	depends on SECURED_MODE_IMAGE
 
+source "board/solidrun/clearfog/Kconfig"
+
 endif
board/solidrun/clearfog/Kconfig new file +18 -0
new file mode 100644
index 0000000000..936d5918f8
@@ -0,0 +1,18 @@
+menu "ClearFog configuration"
+	depends on TARGET_CLEARFOG
+
+config TARGET_CLEARFOG_BASE
+	bool "Use ClearFog Base static configuration"
+	help
+	  Use the ClearFog Base as the static configuration instead of the
+	  default which uses the ClearFog Pro.
+
+	  Runtime board detection is always attempted and used if available. The
+	  static configuration is used as a fallback in cases where runtime
+	  detection is disabled, is not available in hardware, or otherwise fails.
+
+	  Only newer revisions of the ClearFog product line support runtime
+	  detection via additional EEPROM hardware. This option enables selecting
+	  the Base variant for older hardware revisions.
+
+endmenu
board/solidrun/clearfog/clearfog.c +23 -6
index 9b31902c70..c873d00905 100644
@@ -42,6 +42,7 @@ static void cf_read_tlv_data(void)
 	read_tlv_data(&cf_tlv_data);
 }
 
+/* The starting board_serdes_map reflects original Clearfog Pro usage */
 static struct serdes_map board_serdes_map[] = {
 	{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
 	{SGMII1, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
@@ -51,6 +52,13 @@ static struct serdes_map board_serdes_map[] = {
 	{SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
 };
 
+void config_cfbase_serdes_map(void)
+{
+	board_serdes_map[4].serdes_type = USB3_HOST0;
+	board_serdes_map[4].serdes_speed = SERDES_SPEED_5_GBPS;
+	board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
+}
+
 int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
 {
 	cf_read_tlv_data();
@@ -59,12 +67,17 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
 		board_serdes_map[0].serdes_type = PEX0;
 		board_serdes_map[0].serdes_speed = SERDES_SPEED_5_GBPS;
 		board_serdes_map[0].serdes_mode = PEX_ROOT_COMPLEX_X1;
-	}
-
-	if (sr_product_is(&cf_tlv_data, "Clearfog Base")) {
-		board_serdes_map[4].serdes_type = USB3_HOST0;
-		board_serdes_map[4].serdes_speed = SERDES_SPEED_5_GBPS;
-		board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
+	} else if (sr_product_is(&cf_tlv_data, "Clearfog Pro")) {
+		/* handle recognized product as noop, no adjustment required */
+	} else if (sr_product_is(&cf_tlv_data, "Clearfog Base")) {
+		config_cfbase_serdes_map();
+	} else if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE)) {
+		/*
+		 * Fallback to static default. Runtime detection failed,
+		 * hardware support is not present, EEPROM is corrupt,
+		 * or an unrecognized product name is present.
+		 */
+		config_cfbase_serdes_map();
 	}
 
 	*serdes_map_array = board_serdes_map;
@@ -171,6 +184,8 @@ int board_init(void)
 int checkboard(void)
 {
 	char *board = "Clearfog Pro";
+	if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE))
+		board = "Clearfog Base";
 
 	cf_read_tlv_data();
 	if (strlen(cf_tlv_data.tlv_product_name[0]) > 0)
@@ -200,6 +215,8 @@ int board_late_init(void)
 		env_set("fdtfile", "armada-385-clearfog-gtr-s4.dtb");
 	else if (sr_product_is(&cf_tlv_data, "Clearfog GTR L8"))
 		env_set("fdtfile", "armada-385-clearfog-gtr-l8.dtb");
+	else if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE))
+		env_set("fdtfile", "armada-388-clearfog-base.dtb");
 
 	return 0;
 }
Signature · 1 line
2.20.1
#8 lore raw

PATCH v5 4/12 arm: mvebu: clearfog: initial ClearFog Base variant

Quoted 112 lines · Joel Johnson

Add a unique entry for ClearFog Base variant, reflected in the board name and adjusted SerDes topology.

---

v2 changes:
- reworked based on Baruch's run-time TLV EEPROM detection series
v3 changes:
- rebased on mvebu merged run-time TLV EEPROM detection series
- minor update to help test regarding runtime detection failures
v4 changes:
- use runtime static config adjust instead of #ifdef in cases where hardware EEPROM detection fails or is disabled in build
SPL size change for defconfig increases 36 bytes (122893 to 122929) SPL size change for defconfig+Base increases 60 bytes (122893 to 122953)
- add placeholder support for EEPROM based Clearfog Pro, based on initial name confirmation from Baruch. I wanted to include the check at least in the patch for review to indicate expected usage to ensure that a Clearfog Pro EEPROM device boots correctly even if the image is built with Base static configuration. If there are other prerelease concerns and this should be added separately later, I'd be fine with that too.
- Note that this approach *does not* currently provide any mechanism for EEPROM detected boards to have their SFP speed changed or switch between PCIE/SATA signalling. I'm assuming that will be done based on hardware detection, but confirmation/acceptance in review would be appreciated so it can be revisited if needed.
v5 changes:
- only make Base variant adjustment based on runtime configuration

---
  arch/arm/mach-mvebu/Kconfig        |  2 ++
  board/solidrun/clearfog/Kconfig    | 18 ++++++++++++++++++
  board/solidrun/clearfog/clearfog.c | 29 +++++++++++++++++++++++------
  3 files changed, 43 insertions(+), 6 deletions(-)

create mode 100644 board/solidrun/clearfog/Kconfig

arch/arm/mach-mvebu/Kconfig +2 -0
index bc5eaa5a76..161dee937f 100644
@@ -280,4 +280,6 @@ config SECURED_MODE_CSK_INDEX
  	default 0
  	depends on SECURED_MODE_IMAGE
 
+source "board/solidrun/clearfog/Kconfig"
+
  endif
board/solidrun/clearfog/Kconfig new file +18 -0
new file mode 100644
index 0000000000..936d5918f8
@@ -0,0 +1,18 @@
+menu "ClearFog configuration"
+	depends on TARGET_CLEARFOG
+
+config TARGET_CLEARFOG_BASE
+	bool "Use ClearFog Base static configuration"
+	help
+	  Use the ClearFog Base as the static configuration instead of the
+	  default which uses the ClearFog Pro.
+
+	  Runtime board detection is always attempted and used if available. The
+	  static configuration is used as a fallback in cases where runtime
+	  detection is disabled, is not available in hardware, or otherwise fails.
+
+	  Only newer revisions of the ClearFog product line support runtime
+	  detection via additional EEPROM hardware. This option enables selecting
+	  the Base variant for older hardware revisions.
+
+endmenu
board/solidrun/clearfog/clearfog.c +10 -6
index 9b31902c70..c873d00905 100644
@@ -42,6 +42,7 @@ static void cf_read_tlv_data(void)
  	read_tlv_data(&cf_tlv_data);
  }
 
+/* The starting board_serdes_map reflects original Clearfog Pro usage */
  static struct serdes_map board_serdes_map[] = {
  	{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
  	{SGMII1, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
@@ -51,6 +52,13 @@ static struct serdes_map board_serdes_map[] = {
  	{SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
  };
 
+void config_cfbase_serdes_map(void)
+{
+	board_serdes_map[4].serdes_type = USB3_HOST0;
+	board_serdes_map[4].serdes_speed = SERDES_SPEED_5_GBPS;
+	board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
+}
+
  int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
  {
  	cf_read_tlv_data();
@@ -59,12 +67,17 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
  		board_serdes_map[0].serdes_type = PEX0;
  		board_serdes_map[0].serdes_speed = SERDES_SPEED_5_GBPS;
  		board_serdes_map[0].serdes_mode = PEX_ROOT_COMPLEX_X1;
-	}
-
-	if (sr_product_is(&cf_tlv_data, "Clearfog Base")) {
-		board_serdes_map[4].serdes_type = USB3_HOST0;
-		board_serdes_map[4].serdes_speed = SERDES_SPEED_5_GBPS;
-		board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
+	} else if (sr_product_is(&cf_tlv_data, "Clearfog Pro")) {
+		/* handle recognized product as noop, no adjustment required */

board/solidrun/clearfog/clearfog.c int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) · line 81

Quoted 10 lines
board/solidrun/clearfog/clearfog.c +9 -0
+	} else if (sr_product_is(&cf_tlv_data, "Clearfog Base")) {
+		config_cfbase_serdes_map();
+	} else if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE)) {
+		/*
+		 * Fallback to static default. Runtime detection failed,
+		 * hardware support is not present, EEPROM is corrupt,
+		 * or an unrecognized product name is present.
+		 */
+		config_cfbase_serdes_map();
  	}

Would it make sense to add a message, if no board type has been "detected" here at all (else case)?

Thanks,
Stefan

#9 lore raw

PATCH v5 4/12 arm: mvebu: clearfog: initial ClearFog Base variant

Quoted 142 lines · Stefan Roese
Quoted 127 lines · Joel Johnson

Add a unique entry for ClearFog Base variant, reflected in the board name and adjusted SerDes topology.

---

v2 changes:
- reworked based on Baruch's run-time TLV EEPROM detection series
v3 changes:
- rebased on mvebu merged run-time TLV EEPROM detection series
- minor update to help test regarding runtime detection failures
v4 changes:
- use runtime static config adjust instead of #ifdef in cases where hardware EEPROM detection fails or is disabled in build SPL size change for defconfig increases 36 bytes (122893 to
122929)
SPL size change for defconfig+Base increases 60 bytes (122893 to
122953)
- add placeholder support for EEPROM based Clearfog Pro, based on initial name confirmation from Baruch. I wanted to include the
check
at least in the patch for review to indicate expected usage to ensure that a Clearfog Pro EEPROM device boots correctly even if
the
image is built with Base static configuration. If there are other prerelease concerns and this should be added separately later,
I'd
be fine with that too.
- Note that this approach *does not* currently provide any
mechanism
for EEPROM detected boards to have their SFP speed changed or
switch
between PCIE/SATA signalling. I'm assuming that will be done
based on
hardware detection, but confirmation/acceptance in review would
be
appreciated so it can be revisited if needed.
v5 changes:
- only make Base variant adjustment based on runtime configuration

---
  arch/arm/mach-mvebu/Kconfig        |  2 ++
  board/solidrun/clearfog/Kconfig    | 18 ++++++++++++++++++
  board/solidrun/clearfog/clearfog.c | 29 
+++++++++++++++++++++++------
  3 files changed, 43 insertions(+), 6 deletions(-)

create mode 100644 board/solidrun/clearfog/Kconfig

arch/arm/mach-mvebu/Kconfig +1 -0
index bc5eaa5a76..161dee937f 100644
@@ -280,4 +280,6 @@ config SECURED_MODE_CSK_INDEX
  	default 0
  	depends on SECURED_MODE_IMAGE
  +source "board/solidrun/clearfog/Kconfig"
+
  endif
board/solidrun/clearfog/Kconfig new file +10 -0
new file mode 100644
index 0000000000..936d5918f8
@@ -0,0 +1,18 @@
+menu "ClearFog configuration"
+	depends on TARGET_CLEARFOG
+
+config TARGET_CLEARFOG_BASE
+	bool "Use ClearFog Base static configuration"
+	help
+	  Use the ClearFog Base as the static configuration instead of the
+	  default which uses the ClearFog Pro.
+
+	  Runtime board detection is always attempted and used if available. 

The

board/solidrun/clearfog/Kconfig new file +2 -0
+	  static configuration is used as a fallback in cases where runtime
+	  detection is disabled, is not available in hardware, or otherwise 

fails.

board/solidrun/clearfog/Kconfig new file +3 -0
+
+	  Only newer revisions of the ClearFog product line support runtime
+	  detection via additional EEPROM hardware. This option enables 

selecting

board/solidrun/clearfog/Kconfig new file +3 -0
+	  the Base variant for older hardware revisions.
+
+endmenu
board/solidrun/clearfog/clearfog.c +0 -0
index 9b31902c70..c873d00905 100644
@@ -42,6 +42,7 @@ static void cf_read_tlv_data(void)
  	read_tlv_data(&cf_tlv_data);
  }
  +/* The starting board_serdes_map reflects original Clearfog Pro 

usage */
static struct serdes_map board_serdes_map[] = {
{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0}, {SGMII1, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},

board/solidrun/clearfog/clearfog.c +8 -6
@@ -51,6 +52,13 @@ static struct serdes_map board_serdes_map[] = {
  	{SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
  };
  +void config_cfbase_serdes_map(void)
+{
+	board_serdes_map[4].serdes_type = USB3_HOST0;
+	board_serdes_map[4].serdes_speed = SERDES_SPEED_5_GBPS;
+	board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
+}
+
  int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 
 *count)
  {
  	cf_read_tlv_data();
@@ -59,12 +67,17 @@ int hws_board_topology_load(struct serdes_map 
 **serdes_map_array, u8 *count)
  		board_serdes_map[0].serdes_type = PEX0;
  		board_serdes_map[0].serdes_speed = SERDES_SPEED_5_GBPS;
  		board_serdes_map[0].serdes_mode = PEX_ROOT_COMPLEX_X1;
-	}
-
-	if (sr_product_is(&cf_tlv_data, "Clearfog Base")) {
-		board_serdes_map[4].serdes_type = USB3_HOST0;
-		board_serdes_map[4].serdes_speed = SERDES_SPEED_5_GBPS;
-		board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
+	} else if (sr_product_is(&cf_tlv_data, "Clearfog Pro")) {
+		/* handle recognized product as noop, no adjustment required */

board/solidrun/clearfog/clearfog.c int hws_board_topology_load(struct serdes_map · line 82

Quoted 10 lines
board/solidrun/clearfog/clearfog.c +9 -0
+	} else if (sr_product_is(&cf_tlv_data, "Clearfog Base")) {
+		config_cfbase_serdes_map();
+	} else if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE)) {
+		/*
+		 * Fallback to static default. Runtime detection failed,
+		 * hardware support is not present, EEPROM is corrupt,
+		 * or an unrecognized product name is present.
+		 */
+		config_cfbase_serdes_map();
  	}

Would it make sense to add a message, if no board type has been "detected" here at all (else case)?

Quoted 2 lines

Thanks,
Stefan

I suppose it could, I was using the printed board model but that itself isn't enough to distinguish between an EEPROM detected unit and a static fallback.

Joel

#10 lore raw

PATCH v5 5/12 arm: mvebu: clearfog: Add option for 2.5 Gbps SFP

In reply to Joel Johnson

While newer Linux kernels provide autoconfiguration of SFP, provide an option for setting in U-Boot Kconfig for use prior to booting.

---

v2 changes:
- fixed help indentation
v3 changes:
- none
v4 changes:
- adjust static SerDes configuration at runtime instead of #ifdef
v5 changes:
- make independent of runtime detection

---
 board/solidrun/clearfog/Kconfig    | 7 +++++++
 board/solidrun/clearfog/clearfog.c | 5 +++++
 2 files changed, 12 insertions(+)
board/solidrun/clearfog/Kconfig +7 -0
index 936d5918f8..c910e17093 100644
@@ -15,4 +15,11 @@ config TARGET_CLEARFOG_BASE
 	  detection via additional EEPROM hardware. This option enables selecting
 	  the Base variant for older hardware revisions.
 
+config CLEARFOG_SFP_25GB
+	bool "Enable 2.5 Gbps mode for SFP"
+	help
+	  Set the SFP module connection to support 2.5 Gbps transfer speed for the
+	  SGMII connection (requires a supporting SFP). By default, transfer speed
+	  of 1.25 Gbps is used, suitable for a more common 1 Gbps SFP module.
+
 endmenu
board/solidrun/clearfog/clearfog.c +5 -0
index c873d00905..064ce4e520 100644
@@ -63,6 +63,11 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
 {
 	cf_read_tlv_data();
 
+	/* Apply build configuration options before runtime configuration */
+	if (IS_ENABLED(CONFIG_CLEARFOG_SFP_25GB))
+		board_serdes_map[5].serdes_speed = SERDES_SPEED_3_125_GBPS;
+
+	/* Apply runtime detection changes */
 	if (sr_product_is(&cf_tlv_data, "Clearfog GTR")) {
 		board_serdes_map[0].serdes_type = PEX0;
 		board_serdes_map[0].serdes_speed = SERDES_SPEED_5_GBPS;
Signature · 1 line
2.20.1
#11 lore raw

PATCH v5 5/12 arm: mvebu: clearfog: Add option for 2.5 Gbps SFP

Quoted 42 lines · Joel Johnson

While newer Linux kernels provide autoconfiguration of SFP, provide an option for setting in U-Boot Kconfig for use prior to booting.

---

v2 changes:
- fixed help indentation
v3 changes:
- none
v4 changes:
- adjust static SerDes configuration at runtime instead of #ifdef
v5 changes:
- make independent of runtime detection

---
  board/solidrun/clearfog/Kconfig    | 7 +++++++
  board/solidrun/clearfog/clearfog.c | 5 +++++
  2 files changed, 12 insertions(+)
board/solidrun/clearfog/Kconfig +7 -0
index 936d5918f8..c910e17093 100644
@@ -15,4 +15,11 @@ config TARGET_CLEARFOG_BASE
  	  detection via additional EEPROM hardware. This option enables selecting
  	  the Base variant for older hardware revisions.
 
+config CLEARFOG_SFP_25GB
+	bool "Enable 2.5 Gbps mode for SFP"
+	help
+	  Set the SFP module connection to support 2.5 Gbps transfer speed for the
+	  SGMII connection (requires a supporting SFP). By default, transfer speed
+	  of 1.25 Gbps is used, suitable for a more common 1 Gbps SFP module.
+
  endmenu
board/solidrun/clearfog/clearfog.c +0 -0
index c873d00905..064ce4e520 100644

board/solidrun/clearfog/clearfog.c int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) · line 68

Quoted 6 lines
board/solidrun/clearfog/clearfog.c +3 -0
@@ -63,6 +63,11 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
  {
  	cf_read_tlv_data();
 
+	/* Apply build configuration options before runtime configuration */
+	if (IS_ENABLED(CONFIG_CLEARFOG_SFP_25GB))
+		board_serdes_map[5].serdes_speed = SERDES_SPEED_3_125_GBPS;

Just checking: Your option is for 2.5 gbps and you configure here to 3.125 gpbs. Is this intended?

Thanks,
Stefan

#12 lore raw

PATCH v5 5/12 arm: mvebu: clearfog: Add option for 2.5 Gbps SFP

Hi Stefan,

Quoted 42 lines · Stefan Roese
Quoted 41 lines · Joel Johnson

While newer Linux kernels provide autoconfiguration of SFP, provide an option for setting in U-Boot Kconfig for use prior to booting.

---

v2 changes:
- fixed help indentation
v3 changes:
- none
v4 changes:
- adjust static SerDes configuration at runtime instead of #ifdef
v5 changes:
- make independent of runtime detection

---
  board/solidrun/clearfog/Kconfig    | 7 +++++++
  board/solidrun/clearfog/clearfog.c | 5 +++++
  2 files changed, 12 insertions(+)
board/solidrun/clearfog/Kconfig +6 -0
index 936d5918f8..c910e17093 100644
@@ -15,4 +15,11 @@ config TARGET_CLEARFOG_BASE
  	  detection via additional EEPROM hardware. This option enables selecting
  	  the Base variant for older hardware revisions.
  +config CLEARFOG_SFP_25GB
+	bool "Enable 2.5 Gbps mode for SFP"
+	help
+	  Set the SFP module connection to support 2.5 Gbps transfer speed for the
+	  SGMII connection (requires a supporting SFP). By default, transfer speed
+	  of 1.25 Gbps is used, suitable for a more common 1 Gbps SFP module.
+
  endmenu
board/solidrun/clearfog/clearfog.c +0 -0
index c873d00905..064ce4e520 100644
@@ -63,6 +63,11 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
Quoted 8 lines

board/solidrun/clearfog/clearfog.c int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) · line 68

Quoted 5 lines
board/solidrun/clearfog/clearfog.c +2 -0
  {
  	cf_read_tlv_data();
  +	/* Apply build configuration options before runtime configuration */
+	if (IS_ENABLED(CONFIG_CLEARFOG_SFP_25GB))
+		board_serdes_map[5].serdes_speed = SERDES_SPEED_3_125_GBPS;

Just checking: Your option is for 2.5 gbps and you configure here to 3.125 gpbs. Is this intended?

This is intended. Serdes encoding is 8b/10b. So for 2.5Gbps you need serdes rate of 3.125Gbps. For 1Gbps we already set 1.25Gpbs serdes rate (SERDES_SPEED_1_25_GBPS) in board_serdes_map[].

baruch

--
http://baruch.siach.name/blog/ ~. .~ Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
- baruch at tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -

#13 lore raw

PATCH v5 5/12 arm: mvebu: clearfog: Add option for 2.5 Gbps SFP

Quoted 55 lines · Baruch Siach

Hi Stefan,

Quoted 42 lines · Stefan Roese
Quoted 41 lines · Joel Johnson

While newer Linux kernels provide autoconfiguration of SFP, provide an option for setting in U-Boot Kconfig for use prior to booting.

---

v2 changes:
- fixed help indentation
v3 changes:
- none
v4 changes:
- adjust static SerDes configuration at runtime instead of #ifdef
v5 changes:
- make independent of runtime detection

---
   board/solidrun/clearfog/Kconfig    | 7 +++++++
   board/solidrun/clearfog/clearfog.c | 5 +++++
   2 files changed, 12 insertions(+)
board/solidrun/clearfog/Kconfig +6 -0
index 936d5918f8..c910e17093 100644
@@ -15,4 +15,11 @@ config TARGET_CLEARFOG_BASE
   	  detection via additional EEPROM hardware. This option enables selecting
   	  the Base variant for older hardware revisions.
   +config CLEARFOG_SFP_25GB
+	bool "Enable 2.5 Gbps mode for SFP"
+	help
+	  Set the SFP module connection to support 2.5 Gbps transfer speed for the
+	  SGMII connection (requires a supporting SFP). By default, transfer speed
+	  of 1.25 Gbps is used, suitable for a more common 1 Gbps SFP module.
+
   endmenu
board/solidrun/clearfog/clearfog.c +0 -0
index c873d00905..064ce4e520 100644
@@ -63,6 +63,11 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
Quoted 8 lines

board/solidrun/clearfog/clearfog.c int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) · line 68

Quoted 5 lines
board/solidrun/clearfog/clearfog.c +2 -0
   {
   	cf_read_tlv_data();
   +	/* Apply build configuration options before runtime configuration */
+	if (IS_ENABLED(CONFIG_CLEARFOG_SFP_25GB))
+		board_serdes_map[5].serdes_speed = SERDES_SPEED_3_125_GBPS;

Just checking: Your option is for 2.5 gbps and you configure here to 3.125 gpbs. Is this intended?

Quoted 3 lines

This is intended. Serdes encoding is 8b/10b. So for 2.5Gbps you need serdes rate of 3.125Gbps. For 1Gbps we already set 1.25Gpbs serdes rate (SERDES_SPEED_1_25_GBPS) in board_serdes_map[].

Makes sense. Thanks.

Thanks,
Stefan

#14 lore raw

PATCH v5 6/12 arm: mvebu: clearfog: Add SATA mode flags

In reply to Joel Johnson

The mPCIe slots on ClearFog Pro and ClearFog Base may be alternately configured for SATA usage.

---

v2 changes:
- fixed help indentation
v3 changes:
- none
v4 changes:
- adjust static SerDes configuration at runtime instead of #ifdef
- add setting of swap_rx for SATA (as yet untested on hardware)
v5 changes:
- make independent of runtime detection

---
 board/solidrun/clearfog/Kconfig    | 17 +++++++++++++++++
 board/solidrun/clearfog/clearfog.c | 15 +++++++++++++++
 2 files changed, 32 insertions(+)
board/solidrun/clearfog/Kconfig +17 -0
index c910e17093..44224d903d 100644
@@ -15,6 +15,23 @@ config TARGET_CLEARFOG_BASE
 	  detection via additional EEPROM hardware. This option enables selecting
 	  the Base variant for older hardware revisions.
 
+config CLEARFOG_CON3_SATA
+	bool "Use CON3 slot in SATA mode"
+	help
+	  Use the CON3 port with SATA protocol instead of the default PCIe.
+	  The ClearFog port allows usage of either mSATA or miniPCIe
+	  modules, but the desired protocol must be configured at build
+	  time since it affects the SerDes topology layout.
+
+config CLEARFOG_CON2_SATA
+	bool "Use CON2 slot in SATA mode"
+	depends on !TARGET_CLEARFOG_BASE
+	help
+	  Use the CON2 port with SATA protocol instead of the default PCIe.
+	  The ClearFog port allows usage of either mSATA or miniPCIe
+	  modules, but the desired protocol must be configured at build
+	  time since it affects the SerDes topology layout.
+
 config CLEARFOG_SFP_25GB
 	bool "Enable 2.5 Gbps mode for SFP"
 	help
board/solidrun/clearfog/clearfog.c +15 -0
index 064ce4e520..f650e2b40e 100644
@@ -67,6 +67,21 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
 	if (IS_ENABLED(CONFIG_CLEARFOG_SFP_25GB))
 		board_serdes_map[5].serdes_speed = SERDES_SPEED_3_125_GBPS;
 
+	if (IS_ENABLED(CONFIG_CLEARFOG_CON2_SATA) &&
+	    !IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE)) {
+		board_serdes_map[4].serdes_type = SATA2;
+		board_serdes_map[4].serdes_speed = SERDES_SPEED_3_GBPS;
+		board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
+		board_serdes_map[4].swap_rx = 1;
+	}
+
+	if (IS_ENABLED(CONFIG_CLEARFOG_CON3_SATA)) {
+		board_serdes_map[2].serdes_type = SATA1;
+		board_serdes_map[2].serdes_speed = SERDES_SPEED_3_GBPS;
+		board_serdes_map[2].serdes_mode = SERDES_DEFAULT_MODE;
+		board_serdes_map[2].swap_rx = 1;
+	}
+
 	/* Apply runtime detection changes */
 	if (sr_product_is(&cf_tlv_data, "Clearfog GTR")) {
 		board_serdes_map[0].serdes_type = PEX0;
Signature · 1 line
2.20.1
#15 lore raw

PATCH v5 6/12 arm: mvebu: clearfog: Add SATA mode flags

Hi Joel,

Quoted 55 lines · Joel Johnson

The mPCIe slots on ClearFog Pro and ClearFog Base may be alternately configured for SATA usage.

---

v2 changes:
- fixed help indentation
v3 changes:
- none
v4 changes:
- adjust static SerDes configuration at runtime instead of #ifdef
- add setting of swap_rx for SATA (as yet untested on hardware)
v5 changes:
- make independent of runtime detection

---
 board/solidrun/clearfog/Kconfig    | 17 +++++++++++++++++
 board/solidrun/clearfog/clearfog.c | 15 +++++++++++++++
 2 files changed, 32 insertions(+)
board/solidrun/clearfog/Kconfig +17 -0
index c910e17093..44224d903d 100644
@@ -15,6 +15,23 @@ config TARGET_CLEARFOG_BASE
 	  detection via additional EEPROM hardware. This option enables selecting
 	  the Base variant for older hardware revisions.
 
+config CLEARFOG_CON3_SATA
+	bool "Use CON3 slot in SATA mode"
+	help
+	  Use the CON3 port with SATA protocol instead of the default PCIe.
+	  The ClearFog port allows usage of either mSATA or miniPCIe
+	  modules, but the desired protocol must be configured at build
+	  time since it affects the SerDes topology layout.
+
+config CLEARFOG_CON2_SATA
+	bool "Use CON2 slot in SATA mode"
+	depends on !TARGET_CLEARFOG_BASE
+	help
+	  Use the CON2 port with SATA protocol instead of the default PCIe.
+	  The ClearFog port allows usage of either mSATA or miniPCIe
+	  modules, but the desired protocol must be configured at build
+	  time since it affects the SerDes topology layout.
+
 config CLEARFOG_SFP_25GB
 	bool "Enable 2.5 Gbps mode for SFP"
 	help
board/solidrun/clearfog/clearfog.c +0 -0
index 064ce4e520..f650e2b40e 100644

board/solidrun/clearfog/clearfog.c int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) · line 71

Quoted 5 lines
board/solidrun/clearfog/clearfog.c +2 -0
@@ -67,6 +67,21 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
 	if (IS_ENABLED(CONFIG_CLEARFOG_SFP_25GB))
 		board_serdes_map[5].serdes_speed = SERDES_SPEED_3_125_GBPS;
 
+	if (IS_ENABLED(CONFIG_CLEARFOG_CON2_SATA) &&
+	    !IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE)) {

This second condition looks redundant. CONFIG_CLEARFOG_CON2_SATA already depends on !CONFIG_TARGET_CLEARFOG_BASE at the Kconfig level above.

Looks good to me otherwise.

Have you had a chance to test mSATA?

Quoted 6 lines
board/solidrun/clearfog/clearfog.c +6 -0
+		board_serdes_map[4].serdes_type = SATA2;
+		board_serdes_map[4].serdes_speed = SERDES_SPEED_3_GBPS;
+		board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
+		board_serdes_map[4].swap_rx = 1;
+	}
+

board/solidrun/clearfog/clearfog.c int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) · line 87

Quoted 10 lines
board/solidrun/clearfog/clearfog.c +7 -0
+	if (IS_ENABLED(CONFIG_CLEARFOG_CON3_SATA)) {
+		board_serdes_map[2].serdes_type = SATA1;
+		board_serdes_map[2].serdes_speed = SERDES_SPEED_3_GBPS;
+		board_serdes_map[2].serdes_mode = SERDES_DEFAULT_MODE;
+		board_serdes_map[2].swap_rx = 1;
+	}
+
 	/* Apply runtime detection changes */
 	if (sr_product_is(&cf_tlv_data, "Clearfog GTR")) {
 		board_serdes_map[0].serdes_type = PEX0;

baruch

Signature · 3 lines
     http://baruch.siach.name/blog/                  ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch at tkos.co.il - tel: +972.2.679.5364, http://www.tkos.co.il -
#16 lore raw

PATCH v5 6/12 arm: mvebu: clearfog: Add SATA mode flags

Quoted 15 lines · Baruch Siach

Hi Joel,

Quoted 12 lines · Joel Johnson
board/solidrun/clearfog/Kconfig +10 -0
+
+config CLEARFOG_CON2_SATA
+	bool "Use CON2 slot in SATA mode"
+	depends on !TARGET_CLEARFOG_BASE
+	help
+	  Use the CON2 port with SATA protocol instead of the default PCIe.
+	  The ClearFog port allows usage of either mSATA or miniPCIe
+	  modules, but the desired protocol must be configured at build
+	  time since it affects the SerDes topology layout.
+
Quoted 8 lines

board/solidrun/clearfog/clearfog.c int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) · line 71

Quoted 4 lines
board/solidrun/clearfog/clearfog.c +2 -0
+	if (IS_ENABLED(CONFIG_CLEARFOG_CON2_SATA) &&
+	    !IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE)) {

This second condition looks redundant. CONFIG_CLEARFOG_CON2_SATA already
depends on !CONFIG_TARGET_CLEARFOG_BASE at the Kconfig level above.

It is redundant between the config and code sides - I viewed the check in code and the final check and the config entry a convenience to indicate to a configuring user that an option isn't available. If there's a prevailing standard in U-Boot to treat the configuration as pristine or otherwise not want the redundancy, I wouldn't have an issue removing the double-check in code.

Quoted 3 lines

Looks good to me otherwise.

Have you had a chance to test mSATA?

Yes, I added a brief overview to the cover letter - I tested on a ClearFog Base and verified that the CON3 setting does in fact enable SATA, detect the drive, and both U-Boot and Linux have access to the block device. Strictly speaking I only tested CON3 and not CON2, but both run identical parallel paths.

Joel

#17 lore raw

PATCH v5 6/12 arm: mvebu: clearfog: Add SATA mode flags

In reply to Joel Johnson
Quoted 55 lines · Joel Johnson

The mPCIe slots on ClearFog Pro and ClearFog Base may be alternately configured for SATA usage.

---

v2 changes:
- fixed help indentation
v3 changes:
- none
v4 changes:
- adjust static SerDes configuration at runtime instead of #ifdef
- add setting of swap_rx for SATA (as yet untested on hardware)
v5 changes:
- make independent of runtime detection

---
  board/solidrun/clearfog/Kconfig    | 17 +++++++++++++++++
  board/solidrun/clearfog/clearfog.c | 15 +++++++++++++++
  2 files changed, 32 insertions(+)
board/solidrun/clearfog/Kconfig +17 -0
index c910e17093..44224d903d 100644
@@ -15,6 +15,23 @@ config TARGET_CLEARFOG_BASE
  	  detection via additional EEPROM hardware. This option enables selecting
  	  the Base variant for older hardware revisions.
 
+config CLEARFOG_CON3_SATA
+	bool "Use CON3 slot in SATA mode"
+	help
+	  Use the CON3 port with SATA protocol instead of the default PCIe.
+	  The ClearFog port allows usage of either mSATA or miniPCIe
+	  modules, but the desired protocol must be configured at build
+	  time since it affects the SerDes topology layout.
+
+config CLEARFOG_CON2_SATA
+	bool "Use CON2 slot in SATA mode"
+	depends on !TARGET_CLEARFOG_BASE
+	help
+	  Use the CON2 port with SATA protocol instead of the default PCIe.
+	  The ClearFog port allows usage of either mSATA or miniPCIe
+	  modules, but the desired protocol must be configured at build
+	  time since it affects the SerDes topology layout.
+
  config CLEARFOG_SFP_25GB
  	bool "Enable 2.5 Gbps mode for SFP"
  	help
board/solidrun/clearfog/clearfog.c +0 -0
index 064ce4e520..f650e2b40e 100644

board/solidrun/clearfog/clearfog.c int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) · line 76

Quoted 10 lines
board/solidrun/clearfog/clearfog.c +7 -0
@@ -67,6 +67,21 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
  	if (IS_ENABLED(CONFIG_CLEARFOG_SFP_25GB))
  		board_serdes_map[5].serdes_speed = SERDES_SPEED_3_125_GBPS;
 
+	if (IS_ENABLED(CONFIG_CLEARFOG_CON2_SATA) &&
+	    !IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE)) {
+		board_serdes_map[4].serdes_type = SATA2;
+		board_serdes_map[4].serdes_speed = SERDES_SPEED_3_GBPS;
+		board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
+		board_serdes_map[4].swap_rx = 1;
+	}

Please remove !IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE) as Baruch already mentioned.

Other that that:

Thanks,
Stefan

#18 lore raw

PATCH v5 7/12 arm: mvebu: clearfog: Unify DT selection paths

In reply to Joel Johnson

Unify the location of DT selection into board_late_init instead of split between detection and static configuration paths.

---

v2 changes
- newly added in V2 series based on run-time rebasing
v3 changes
- none
v4 changes
- separate change to explicit pro DT into separate commit
v5 changes
- none

---
 board/solidrun/clearfog/clearfog.c | 2 ++
 include/configs/clearfog.h         | 1 -
 2 files changed, 2 insertions(+), 1 deletion(-)
board/solidrun/clearfog/clearfog.c +2 -0
index f650e2b40e..4170fd4775 100644
@@ -237,6 +237,8 @@ int board_late_init(void)
 		env_set("fdtfile", "armada-385-clearfog-gtr-l8.dtb");
 	else if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE))
 		env_set("fdtfile", "armada-388-clearfog-base.dtb");
+	else
+		env_set("fdtfile", "armada-388-clearfog.dtb");
 
 	return 0;
 }
include/configs/clearfog.h +0 -1
index 633187d86f..6ca0474461 100644
@@ -134,7 +134,6 @@
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	RELOCATION_LIMITS_ENV_SETTINGS \
 	LOAD_ADDRESS_ENV_SETTINGS \
-	"fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
 	"console=ttyS0,115200\0" \
 	BOOTENV
 
Signature · 1 line
2.20.1
#19 lore raw

PATCH v5 7/12 arm: mvebu: clearfog: Unify DT selection paths

Quoted 14 lines · Joel Johnson

Unify the location of DT selection into board_late_init instead of split between detection and static configuration paths.

---

v2 changes
- newly added in V2 series based on run-time rebasing
v3 changes
- none
v4 changes
- separate change to explicit pro DT into separate commit
v5 changes
- none

Quoted 1 line

Thanks,
Stefan

#20 lore raw

PATCH v5 8/12 arm: mvebu: clearfog: add SPI offsets

In reply to Joel Johnson

Add reasonable default SPI offsets and ENV size when configured to boot from SPI flash.

---

v2 changes:
- none
v3 changes:
- none
v4 changes:
- none
v5 changes:
- none

There was some reasonable concern raised about duplicating config entries within a board specific config file rather than making board specific configurations within defconfig. This seems to offer a more board localized mechanism to provide platform defaults for core values. As mentioned in the review, this usage seems to match the Kconfig documented intended usage. As noted at
https://www.kernel.org/doc/html/latest/kbuild/kconfig-language.html:
"Default values are not limited to the menu entry where
they are defined. This means the default can be defined somewhere else or be overridden by an earlier definition."

Given that there is some dependency variability with these values I prefer keeping them as Kconfig values, but defer to maintainers. Notably, for the ENV values in this and a later commit, I'm using a pattern already in used several other board configs.

---
 board/solidrun/clearfog/Kconfig | 12 ++++++++++++
 1 file changed, 12 insertions(+)
board/solidrun/clearfog/Kconfig +12 -0
index 44224d903d..ea9c419472 100644
@@ -39,4 +39,16 @@ config CLEARFOG_SFP_25GB
 	  SGMII connection (requires a supporting SFP). By default, transfer speed
 	  of 1.25 Gbps is used, suitable for a more common 1 Gbps SFP module.
 
+config ENV_SECT_SIZE
+	hex "Environment Sector-Size"
+	# Use SPI flash erase block size of 4 KiB
+	default 0x1000 if MVEBU_SPL_BOOT_DEVICE_SPI
+	# Use optimistic 64 KiB erase block, will vary between actual media
+	default 0x10000 if MVEBU_SPL_BOOT_DEVICE_MMC
+
+config SYS_SPI_U_BOOT_OFFS
+	hex "address of u-boot payload in SPI flash"
+	default 0x20000
+	depends on MVEBU_SPL_BOOT_DEVICE_SPI
+
 endmenu
Signature · 1 line
2.20.1
#22 lore raw

PATCH v5 9/12 arm: mvebu: enable working default boot support

In reply to Joel Johnson

With the move to driver model usage, ensure that the required driver support for SPI and MMC booting is available in SPL.

Tested on SolidRun ClearFog devices.

---

v2 changes:
- change "select" for ENV_IS_IN_X to "imply" to allow disabling the default env location and configuring a different one if desired
- remove SPL_DM_GPIO from defconfig, only include if needed for MMC booting
v3 changes:
- none
v4 changes:
- none
v5 changes:
- none

---
 arch/arm/mach-mvebu/Kconfig | 10 ++++++++++
 1 file changed, 10 insertions(+)
arch/arm/mach-mvebu/Kconfig +10 -0
index 161dee937f..32191e7157 100644
@@ -235,9 +235,19 @@ choice
 
 config MVEBU_SPL_BOOT_DEVICE_SPI
 	bool "SPI NOR flash"
+	imply ENV_IS_IN_SPI_FLASH
+	select SPL_DM_SPI
+	select SPL_MTD_SUPPORT
+	select SPL_SPI_FLASH_SUPPORT
+	select SPL_SPI_LOAD
+	select SPL_SPI_SUPPORT
 
 config MVEBU_SPL_BOOT_DEVICE_MMC
 	bool "SDIO/MMC card"
+	imply ENV_IS_IN_MMC
+	# GPIO required for SD card presence detection line
+	select SPL_DM_GPIO
+	select SPL_DM_MMC
 	select SPL_LIBDISK_SUPPORT
 
 config MVEBU_SPL_BOOT_DEVICE_SATA
Signature · 1 line
2.20.1
#24 lore raw

PATCH v5 10/12 arm: mvebu: clearfog: move ENV params to Kconfig

In reply to Joel Johnson

Migrate the values for ENV_SIZE and ENV_OFFSET into board specific Kconfig defaults so they're more accessible for configuration.

---

v2 changes:
- none
v3 changes:
- none
v4 changes:
- none
v5 changes:
- none

---
 board/solidrun/clearfog/Kconfig | 8 ++++++++
 configs/clearfog_defconfig      | 2 --
 2 files changed, 8 insertions(+), 2 deletions(-)
board/solidrun/clearfog/Kconfig +8 -0
index ea9c419472..e8c3f53d84 100644
@@ -39,6 +39,14 @@ config CLEARFOG_SFP_25GB
 	  SGMII connection (requires a supporting SFP). By default, transfer speed
 	  of 1.25 Gbps is used, suitable for a more common 1 Gbps SFP module.
 
+config ENV_SIZE
+	hex "Environment Size"
+	default 0x10000
+
+config ENV_OFFSET
+	hex "Environment offset"
+	default 0xF0000
+
 config ENV_SECT_SIZE
 	hex "Environment Sector-Size"
 	# Use SPI flash erase block size of 4 KiB
configs/clearfog_defconfig +0 -2
index c938448c30..6db8b8acf6 100644
@@ -9,8 +9,6 @@ CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_TARGET_CLEARFOG=y
 CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC=y
-CONFIG_ENV_SIZE=0x10000
-CONFIG_ENV_OFFSET=0xF0000
 CONFIG_DM_GPIO=y
 CONFIG_SPL_MMC_SUPPORT=y
 CONFIG_SPL_SERIAL_SUPPORT=y
Signature · 1 line
2.20.1
#25 lore raw

PATCH v5 10/12 arm: mvebu: clearfog: move ENV params to Kconfig

Quoted 14 lines · Joel Johnson

Migrate the values for ENV_SIZE and ENV_OFFSET into board specific Kconfig defaults so they're more accessible for configuration.

---

v2 changes:
- none
v3 changes:
- none
v4 changes:
- none
v5 changes:
- none

Quoted 1 line

Thanks,
Stefan

#26 lore raw

PATCH v5 11/12 arm: mvebu: clearfog: don't always use SPL MMC

In reply to Joel Johnson

Move MMC booting assuptions from defconfig to Kconfig which includes as needed based on dependent options.

---

v2 changes:
- rebased on master to use Baruch's dynamic MMC/SD offset logic
- update description, will revisit removal of CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC in separate future path if a more viable option is identified
v3 changes:
- none
v4 changes:
- none
v5 changes:
- none

---
 arch/arm/mach-mvebu/Kconfig | 1 +
 configs/clearfog_defconfig  | 2 --
 2 files changed, 1 insertion(+), 2 deletions(-)
arch/arm/mach-mvebu/Kconfig +1 -0
index 32191e7157..4b381a2936 100644
@@ -249,6 +249,7 @@ config MVEBU_SPL_BOOT_DEVICE_MMC
 	select SPL_DM_GPIO
 	select SPL_DM_MMC
 	select SPL_LIBDISK_SUPPORT
+	select SPL_MMC_SUPPORT
 
 config MVEBU_SPL_BOOT_DEVICE_SATA
 	bool "SATA"
configs/clearfog_defconfig +0 -2
index 6db8b8acf6..601b1997ed 100644
@@ -10,7 +10,6 @@ CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_TARGET_CLEARFOG=y
 CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC=y
 CONFIG_DM_GPIO=y
-CONFIG_SPL_MMC_SUPPORT=y
 CONFIG_SPL_SERIAL_SUPPORT=y
 CONFIG_NR_DRAM_BANKS=2
 CONFIG_SPL=y
@@ -42,7 +41,6 @@ CONFIG_CMD_CACHE=y
 CONFIG_CMD_TIME=y
 # CONFIG_SPL_PARTITION_UUIDS is not set
 CONFIG_DEFAULT_DEVICE_TREE="armada-388-clearfog"
-CONFIG_ENV_IS_IN_MMC=y
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_SPL_OF_TRANSLATE=y
 CONFIG_AHCI_MVEBU=y
Signature · 1 line
2.20.1
#28 lore raw

PATCH v5 12/12 arm: mvebu: clearfog: Use Pro DT by default

In reply to Joel Johnson

Switch to explicitly using the Pro variant DT, which has been available since Linux 4.11.

---

v4 changes:
- new
v5 changes:
- none

I separated out this change to the end of the series since it drew questioning on prior review. I'd still advocate for making the change, since especially with the additions of static variants and runtime detection, it becomes easier from within a booted kernel to identify the type and version of U-Boot image installed. Without making this change, it becomes less direct to determine an actual Pro vs. Base, vs old U-Boot image maybe supporting some hybrid variant configuration.

Even in the Linux kernel adding of the Pro DTS, it is indicated that it was meant for backwards compatibility.

Except for cases where checking is done directly against the product name from userspace, I don't see downsides even from a compatibility perspective for not making this change. In cases where checking *is* done from userspace, the broadening of the Clearfog product line would seem to mean that userspace checking should be flagged as needing to be udpated as well (or glob/regex matched as needed).

---
 board/solidrun/clearfog/clearfog.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
board/solidrun/clearfog/clearfog.c +1 -1
index 4170fd4775..c31cfcb242 100644
@@ -238,7 +238,7 @@ int board_late_init(void)
 	else if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE))
 		env_set("fdtfile", "armada-388-clearfog-base.dtb");
 	else
-		env_set("fdtfile", "armada-388-clearfog.dtb");
+		env_set("fdtfile", "armada-388-clearfog-pro.dtb");
 
 	return 0;
 }
Signature · 1 line
2.20.1
#29 lore raw

PATCH v5 12/12 arm: mvebu: clearfog: Use Pro DT by default

Hi Joel,

Quoted 21 lines · Joel Johnson

Switch to explicitly using the Pro variant DT, which has been available since Linux 4.11.

---

v4 changes:
- new
v5 changes:
- none

I separated out this change to the end of the series since it drew questioning on prior review. I'd still advocate for making the change, since especially with the additions of static variants and runtime detection, it becomes easier from within a booted kernel to identify the type and version of U-Boot image installed. Without making this change, it becomes less direct to determine an actual Pro vs. Base, vs old U-Boot image maybe supporting some hybrid variant configuration.

Even in the Linux kernel adding of the Pro DTS, it is indicated that it was meant for backwards compatibility.

Quoted 6 lines

Except for cases where checking is done directly against the product name from userspace, I don't see downsides even from a compatibility perspective for not making this change. In cases where checking *is* done from userspace, the broadening of the Clearfog product line would seem to mean that userspace checking should be flagged as needing to be udpated as well (or glob/regex matched as needed).

One downside I see is that boot of kernels older than 4.11 will fail. But maybe since we already assume a newer kernel for armada-388-clearfog-base.dtb we can do that for -pro as well.

By the way, does env_set() override the stored environment?

baruch

Quoted 19 lines
---
 board/solidrun/clearfog/clearfog.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
board/solidrun/clearfog/clearfog.c +1 -1
index 4170fd4775..c31cfcb242 100644
@@ -238,7 +238,7 @@ int board_late_init(void)
 	else if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE))
 		env_set("fdtfile", "armada-388-clearfog-base.dtb");
 	else
-		env_set("fdtfile", "armada-388-clearfog.dtb");
+		env_set("fdtfile", "armada-388-clearfog-pro.dtb");
 
 	return 0;
 }
Signature · 3 lines
     http://baruch.siach.name/blog/                  ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch at tkos.co.il - tel: +972.2.679.5364, http://www.tkos.co.il -
#30 lore raw

PATCH v5 12/12 arm: mvebu: clearfog: Use Pro DT by default

Quoted 35 lines · Baruch Siach

Hi Joel,

Quoted 24 lines · Joel Johnson

Switch to explicitly using the Pro variant DT, which has been available since Linux 4.11.

---

v4 changes:
- new
v5 changes:
- none

I separated out this change to the end of the series since it drew questioning on prior review. I'd still advocate for making the change, since especially with the additions of static variants and runtime detection, it becomes easier from within a booted kernel to identify the
type and version of U-Boot image installed. Without making this change,
it becomes less direct to determine an actual Pro vs. Base, vs old U-Boot image maybe supporting some hybrid variant configuration.

Even in the Linux kernel adding of the Pro DTS, it is indicated that it
was meant for backwards compatibility.

Quoted 7 lines

Except for cases where checking is done directly against the product name from userspace, I don't see downsides even from a compatibility perspective for not making this change. In cases where checking *is* done from userspace, the broadening of the Clearfog product line would seem to mean that userspace checking should be flagged as needing to be
udpated as well (or glob/regex matched as needed).

Quoted 5 lines

One downside I see is that boot of kernels older than 4.11 will fail. But
maybe since we already assume a newer kernel for armada-388-clearfog-base.dtb
we can do that for -pro as well.

Older kernels is one case, and to be fair there may also be the case of custom images with a newer kernel that for whatever reason (old file glob patterns) don't ship the -pro.dtb file. My testing focused primarily on OpenWRT and Debian, and while certainly not pervasive, I've also tested with current Armbian and Arch Linux ARM builds.

Quoted 1 line

By the way, does env_set() override the stored environment?

I'm not entirely sure of the behavior with duplicate entries, however patch 7 in the series removes the fdtfile entry from being added via CONFIG_EXTRA_ENV_SETTINGS, so it is now only set in one consistent location within board_late_init().

Joel

#31 lore raw

PATCH v5 12/12 arm: mvebu: clearfog: Use Pro DT by default

In reply to Joel Johnson
Quoted 21 lines · Joel Johnson

Switch to explicitly using the Pro variant DT, which has been available since Linux 4.11.

---

v4 changes:
- new
v5 changes:
- none

I separated out this change to the end of the series since it drew questioning on prior review. I'd still advocate for making the change, since especially with the additions of static variants and runtime detection, it becomes easier from within a booted kernel to identify the type and version of U-Boot image installed. Without making this change, it becomes less direct to determine an actual Pro vs. Base, vs old U-Boot image maybe supporting some hybrid variant configuration.

Even in the Linux kernel adding of the Pro DTS, it is indicated that it was meant for backwards compatibility.

Quoted 8 lines

Except for cases where checking is done directly against the product name from userspace, I don't see downsides even from a compatibility perspective for not making this change. In cases where checking *is* done from userspace, the broadening of the Clearfog product line would seem to mean that userspace checking should be flagged as needing to be udpated as well (or glob/regex matched as needed).

Again, please make sure to put the S-o-b line above the first "---" line.

Other that that:

Thanks,
Stefan

#32 lore raw

v5 cover ClearFog Base static variant support

In reply to Joel Johnson

I just wanted to ping on this review
(http://patchwork.ozlabs.org/project/uboot/list/?series=155533) to see if it had reached an agreeable state or if there were still lingering issues. I've been using it without issue against RC releases.

If the plan is to not include it in v2020.04 that's completely reasonable, but I would request review and feedback on blocking issues, otherwise does it have general agreement for merging in the next merge window?

Thanks,
Joel

Quoted 43 lines · Joel Johnson

This patch series adds support for ClearFog Base static configuration, as well as updating and fixing the ClearFog support for MMC and SPI booting.

v2 changes:
- updated against, and dependent on,
https://patchwork.ozlabs.org/cover/1200324
v3 changes:
- rebased against ClearFog runtime TLV EEPROM changes merged into
mvebu/master
v4
- adjust static SerDes configuration at runtime instead of #ifdef
v5
- distinguish build-only config changes (SFP and PCIe/SATA) from runtime detectable config changes
- retested SATA mode in PCIe slot with swap rx changes, confirmed working as presently patched. Only tested with ClearFog Base which only provides single channel, but Pro mechanism is parallel.

Joel Johnson (12):
arm: mvebu: fix SerDes table alignment
arm: mvebu: solidrun: remove hardcoded DTS MAC address
arm: mvebu: clearfog: use Pro name by default
arm: mvebu: clearfog: initial ClearFog Base variant
arm: mvebu: clearfog: Add option for 2.5 Gbps SFP
arm: mvebu: clearfog: Add SATA mode flags
arm: mvebu: clearfog: Unify DT selection paths
arm: mvebu: clearfog: add SPI offsets
arm: mvebu: enable working default boot support
arm: mvebu: clearfog: move ENV params to Kconfig
arm: mvebu: clearfog: don't always use SPL MMC
arm: mvebu: clearfog: Use Pro DT by default

 .../arm/dts/armada-38x-solidrun-microsom.dtsi |  1 -
 arch/arm/mach-mvebu/Kconfig                   | 13 ++++
 .../serdes/a38x/high_speed_env_spec.c         |  6 +-
 board/solidrun/clearfog/Kconfig               | 62 +++++++++++++++++++
 board/solidrun/clearfog/clearfog.c            | 53 +++++++++++++---
 configs/clearfog_defconfig                    |  4 --
 include/configs/clearfog.h                    |  1 -
 7 files changed, 124 insertions(+), 16 deletions(-)
 create mode 100644 board/solidrun/clearfog/Kconfig
#33 lore raw

v5 cover ClearFog Base static variant support

Hi Joel,

Quoted 9 lines · Joel Johnson

I just wanted to ping on this review
(http://patchwork.ozlabs.org/project/uboot/list/?series=155533) to see if it had reached an agreeable state or if there were still lingering issues. I've been using it without issue against RC releases.

If the plan is to not include it in v2020.04 that's completely reasonable, but I would request review and feedback on blocking issues, otherwise does it have general agreement for merging in the next merge window?

I won't pull this into v2020.04 as you might understand. I was hoping to get some reviews and testing from people with access to those boards.

Baruch, could you please check again, if you agree with this approach? Or do you have some change request for this build-time vs run-time detection?

Thanks,
Stefan

Quoted 47 lines

Thanks,
Joel

Quoted 43 lines · Joel Johnson

This patch series adds support for ClearFog Base static configuration, as well as updating and fixing the ClearFog support for MMC and SPI booting.

v2 changes:
? - updated against, and dependent on,
https://patchwork.ozlabs.org/cover/1200324
v3 changes:
? - rebased against ClearFog runtime TLV EEPROM changes merged into mvebu/master
v4
? - adjust static SerDes configuration at runtime instead of #ifdef v5
? - distinguish build-only config changes (SFP and PCIe/SATA) from ??? runtime detectable config changes
? - retested SATA mode in PCIe slot with swap rx changes, confirmed ??? working as presently patched. Only tested with ClearFog Base which ??? only provides single channel, but Pro mechanism is parallel.

Joel Johnson (12):
? arm: mvebu: fix SerDes table alignment
? arm: mvebu: solidrun: remove hardcoded DTS MAC address ? arm: mvebu: clearfog: use Pro name by default ? arm: mvebu: clearfog: initial ClearFog Base variant ? arm: mvebu: clearfog: Add option for 2.5 Gbps SFP ? arm: mvebu: clearfog: Add SATA mode flags
? arm: mvebu: clearfog: Unify DT selection paths ? arm: mvebu: clearfog: add SPI offsets
? arm: mvebu: enable working default boot support ? arm: mvebu: clearfog: move ENV params to Kconfig ? arm: mvebu: clearfog: don't always use SPL MMC ? arm: mvebu: clearfog: Use Pro DT by default

?.../arm/dts/armada-38x-solidrun-microsom.dtsi |? 1 -
?arch/arm/mach-mvebu/Kconfig?????????????????? | 13 ++++
?.../serdes/a38x/high_speed_env_spec.c???????? |? 6 +-
?board/solidrun/clearfog/Kconfig?????????????? | 62 +++++++++++++++++++
?board/solidrun/clearfog/clearfog.c??????????? | 53 +++++++++++++---
?configs/clearfog_defconfig??????????????????? |? 4 --
?include/configs/clearfog.h??????????????????? |? 1 -

?7 files changed, 124 insertions(+), 16 deletions(-) ?create mode 100644 board/solidrun/clearfog/Kconfig

Viele Gr??e,
Stefan

Signature · 3 lines
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de
#34 lore raw

v5 cover ClearFog Base static variant support

Hi Stefan,

Quoted 10 lines · Stefan Roese
Quoted 8 lines · Joel Johnson

I just wanted to ping on this review
(http://patchwork.ozlabs.org/project/uboot/list/?series=155533) to see if it had reached an agreeable state or if there were still lingering issues. I've been using it without issue against RC releases.

If the plan is to not include it in v2020.04 that's completely reasonable, but I would request review and feedback on blocking issues, otherwise does it have general agreement for merging in the next merge window?

Quoted 6 lines

I won't pull this into v2020.04 as you might understand. I was hoping to get some reviews and testing from people with access to those boards.

Baruch, could you please check again, if you agree with this approach? Or do you have some change request for this build-time vs run-time detection?

This series is the end result of discussions between Joel and me on the list with a few iterations. I am fine with this result, and I think it is good to go. I can't test these patches at the moment. Hope to do that some time later.

Thanks,
baruch

Quoted 46 lines
Quoted 35 lines · Joel Johnson
Quoted 34 lines

This patch series adds support for ClearFog Base static configuration, as well as updating and fixing the ClearFog support for MMC and SPI booting.

v2 changes:
- updated against, and dependent on,
https://patchwork.ozlabs.org/cover/1200324
v3 changes:
- rebased against ClearFog runtime TLV EEPROM changes merged into
mvebu/master
v4
- adjust static SerDes configuration at runtime instead of #ifdef
v5
- distinguish build-only config changes (SFP and PCIe/SATA) from runtime detectable config changes
- retested SATA mode in PCIe slot with swap rx changes, confirmed working as presently patched. Only tested with ClearFog Base which only provides single channel, but Pro mechanism is parallel.

Joel Johnson (12):
arm: mvebu: fix SerDes table alignment
arm: mvebu: solidrun: remove hardcoded DTS MAC address
arm: mvebu: clearfog: use Pro name by default
arm: mvebu: clearfog: initial ClearFog Base variant
arm: mvebu: clearfog: Add option for 2.5 Gbps SFP
arm: mvebu: clearfog: Add SATA mode flags
arm: mvebu: clearfog: Unify DT selection paths
arm: mvebu: clearfog: add SPI offsets
arm: mvebu: enable working default boot support
arm: mvebu: clearfog: move ENV params to Kconfig
arm: mvebu: clearfog: don't always use SPL MMC
arm: mvebu: clearfog: Use Pro DT by default

Quoted 9 lines
Quoted 9 lines
 .../arm/dts/armada-38x-solidrun-microsom.dtsi |  1 -
 arch/arm/mach-mvebu/Kconfig                   | 13 ++++
 .../serdes/a38x/high_speed_env_spec.c         |  6 +-
 board/solidrun/clearfog/Kconfig               | 62 +++++++++++++++++++
 board/solidrun/clearfog/clearfog.c            | 53 +++++++++++++---
 configs/clearfog_defconfig                    |  4 --
 include/configs/clearfog.h                    |  1 -
 7 files changed, 124 insertions(+), 16 deletions(-)
 create mode 100644 board/solidrun/clearfog/Kconfig
Quoted 2 lines

Viele Gr??e,
Stefan

--
http://baruch.siach.name/blog/ ~. .~ Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
- baruch at tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -