SG_IO readcd and various bugs

Hi,

Below patch should make readcd (and others) behave, please test.

===== drivers/block/ioctl.c 1.54 vs edited =====

@@ -207,11 +207,8 @@
 		set_device_ro(bdev, n);
 		return 0;
 	default:
-		if (disk->fops->ioctl) {
-			ret = disk->fops->ioctl(inode, file, cmd, arg);
-			if (ret != -EINVAL)
-				return ret;
-		}
+		if (disk->fops->ioctl)
+			return disk->fops->ioctl(inode, file, cmd, arg);
 	}
 	return -ENOTTY;
 }

===== drivers/block/scsi_ioctl.c 1.27 vs edited =====

===== drivers/ide/ide-cd.c 1.46 vs edited =====

@@ -666,8 +666,10 @@
 		struct cdrom_info *info = drive->driver_data;
 		void *sense = &info->sense_data;
 		
-		if (failed && failed->sense)
+		if (failed && failed->sense) {
 			sense = failed->sense;
+			failed->sense_len = rq->sense_len;
+		}
 
 		cdrom_analyze_sense_data(drive, failed, sense);
 	}

@@ -723,7 +725,7 @@
 		 * scsi status byte
 		 */
 		if ((rq->flags & REQ_BLOCK_PC) && !rq->errors)
-			rq->errors = CHECK_CONDITION;
+			rq->errors = SAM_STAT_CHECK_CONDITION;
 
 		/* Check for tray open. */
 		if (sense_key == NOT_READY) {

@@ -1609,10 +1611,18 @@
 
 static void post_transform_command(struct request *req)
 {
-	char *ibuf = req->buffer;
 	u8 *c = req->cmd;
+	char *ibuf;
 
 	if (!blk_pc_request(req))
+		return;
+
+	if (req->bio)
+		ibuf = bio_data(req->bio);
+	else
+		ibuf = req->data;
+
+	if (!ibuf)
 		return;
 
 	/*

===== fs/bio.c 1.45 vs edited =====

@@ -538,12 +538,6 @@
 	bio = __bio_map_user(bdev, uaddr, len, write_to_vm);
 
 	if (bio) {
-		if (bio->bi_size < len) {
-			bio_endio(bio, bio->bi_size, 0);
-			bio_unmap_user(bio, 0);
-			return NULL;
-		}
-
 		/*
 		 * subtle -- if __bio_map_user() ended up bouncing a bio,
 		 * it would normally disappear when its bi_end_io is run.

@@ -551,6 +545,12 @@
 		 * reference to it
 		 */
 		bio_get(bio);
+
+		if (bio->bi_size < len) {
+			bio_endio(bio, bio->bi_size, 0);
+			bio_unmap_user(bio, 0);
+			return NULL;
+		}
 	}
 
 	return bio;

Jens Axboe

Hi there!

The patch makes readcd work just fine here :-) Many thanks!

Now if only writing would also work...

regards
Markus

[15:44:31]-[Fri May 30]-[~]
[plail@plailis_lfs]dvdrecord dev=/dev/hdb speed=4 -v -dummy /video-2/trailer_final_1000_dl.mov Cdrecord-ProDVD-Clone 2.01a12 (i586-pc-linux-gnu) Copyright (C) 1995-2003 Jörg Schilling Unlocked features: ProDVD Clone
Limited features: speed
This copy of cdrecord is licensed for: private/research/educational_non-commercial_use TOC Type: 1 = CD-ROM
devname: '/dev/hdb'
scsibus: -2 target: -2 lun: -2
Warning: Open by 'devname' is unintentional and not supported.
Linux sg driver version: 3.5.27
Using libscg version 'schily-0.7'
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'TEAC '
Identifikation : 'DV-W50E '
Revision : '1.30'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: DVD-RW sequential overwrite
Profile: DVD-RW sequential overwrite (current)
Profile: DVD-RW restricted overwrite (current)
Profile: DVD-R sequential recording (current)
Profile: DVD-ROM
Profile: CD-RW
Profile: CD-R
Profile: CD-ROM
Using generic SCSI-3/mmc-2 DVD-R/DVD-RW driver (mmc_dvd).
Driver flags : DVD MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive buf size : 1605632 = 1568 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 97 MB
Total size: 97 MB = 49843 sectors
Current Secsize: 2048
Total power on hours: 110055
WARNING: Phys disk size 49843 differs from rzone size 2298496! Prerecorded disk?
WARNING: Phys start: 196608 Phys end 246450
Blocks total: 2298496 Blocks current: 2298496 Blocks remaining: 2248653 Starting to write CD/DVD at speed 2 in dummy TAO mode for single session.
Last chance to quit, starting dummy write 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready. BURN-Free is OFF.

Starting new track at sector: 0
Track 01:    1 of   97 MB written (fifo  85%) [buf  67%]  11.5x.cdrecord-ProDVD: Success. write_g1: scsi sendcmd: no error
CDB:  2A 00 00 00 03 07 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70
Sense Key: 0x0 No Additional Sense, Segment 0
Sense Code: 0x00 Qual 0x00 (no additional sense information) Fru 0x0
Sense flags: Blk 0 (not valid) 
resid: 63488

cmd finished after 0.005s timeout 100s

write track data: error after 1587200 bytes
cdrecord-ProDVD: A write error occured.
cdrecord-ProDVD: Please properly read the error message above.
Writing time: 5.198s
Average write speed 14.3x.
Fixating...
Fixating time: 0.464s
cdrecord-ProDVD: fifo had 89 puts and 26 gets.
cdrecord-ProDVD: fifo was 0 times empty and 2 times full, min fill was 82%. You have new mail in /var/mail/plail
[15:45:08]-[Fri May 30]-[~]
[plail@plailis_lfs]

Just realized that C2 scans don't yet work.

regards
Markus

[15:49:37]-[Fri May 30]-[/home/plail]
[root@plailis_lfs]strace /opt/schily/bin/readcd dev=/dev/hdb -c2scan execve("/opt/schily/bin/readcd", ["/opt/schily/bin/readcd", "dev=/dev/hdb", "-c2scan"], [/* 45 vars */]) = 0

brk(0)                                  = 0x806a000
open("/etc/ld.so.preload", O_RDONLY)    = -1 ENOENT (No such file or directory)
open("/etc/ld.so.cache", O_RDONLY)      = 3

fstat64(3, {st_mode=S_IFREG|0644, st_size=66034, ...}) = 0 old_mmap(NULL, 66034, PROT_READ, MAP_PRIVATE, 3, 0) = 0x40017000
close(3) = 0
open("/lib/libc.so.6", O_RDONLY) = 3
read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0\10\332"..., 1024) = 1024 fstat64(3, {st_mode=S_IFREG|0755, st_size=5021367, ...}) = 0 old_mmap(NULL, 1215588, PROT_READ|PROT_EXEC, MAP_PRIVATE, 3, 0) = 0x40028000 mprotect(0x40146000, 44132, PROT_NONE) = 0

old_mmap(0x40146000, 28672, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0x11d000) = 0x40146000
old_mmap(0x4014d000, 15460, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x4014d000
close(3)                                = 0
munmap(0x40017000, 66034)               = 0
brk(0)                                  = 0x806a000
brk(0x806a0a8)                          = 0x806a0a8
brk(0x806b000)                          = 0x806b000
brk(0x806d000)                          = 0x806d000
open("/dev/hdb", O_RDWR|O_NONBLOCK)     = 3
fcntl64(3, F_GETFL)                     = 0x8802 (flags O_RDWR|O_NONBLOCK|O_LARGEFILE)
fcntl64(3, F_SETFL, O_RDWR|O_LARGEFILE) = 0
ioctl(3, 0x5382, 0xbffff164)            = 0
ioctl(3, 0x5386, 0xbffff160)            = 0
ioctl(3, 0x2282, 0xbffff168)            = 0
ioctl(3, 0x5382, 0xbffff104)            = 0
ioctl(3, 0x5386, 0xbffff100)            = 0
ioctl(3, 0x2201, 0xbffff018)            = 0
fstat64(3, {st_mode=S_IFBLK|0660, st_rdev=makedev(3, 64), ...}) = 0
ioctl(3, 0x2272, 0xbffff338)            = 0
ioctl(3, 0x2272, 0xbffff338)            = 0
ioctl(3, 0x2275, 0xbffff334)            = -1 EINVAL (Invalid argument)
ioctl(3, 0x2272, 0xbffff334)            = 0
ioctl(3, 0x2272, 0xbffff318)            = 0
ioctl(3, 0x2272, 0xbffff314)            = 0
old_mmap(NULL, 139264, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40151000
geteuid32()                             = 0
getuid32()                              = 0
getuid32()                              = 0
setreuid32(0xffffffff, 0)               = 0

gettimeofday({1054302587, 28334}, NULL) = 0
ioctl(3, 0x2285, 0xbffff0fc) = 0
gettimeofday({1054302587, 29005}, NULL) = 0
gettimeofday({1054302587, 29274}, NULL) = 0
ioctl(3, 0x2285, 0xbffff13c) = 0
...
...[snip]...
...
ioctl(3, 0x2285, 0xbfffee8c) = 0
gettimeofday({1054302587, 141430}, NULL) = 0
write(2, "Read speed: 8310 kB/s (CD 47x"..., 44Read speed: 8310 kB/s (CD 47x, DVD 6x). ) = 44
write(2, "Write speed: 2770 kB/s (CD 15x"..., 44Write speed: 2770 kB/s (CD 15x, DVD 2x). ) = 44
rt_sigaction(SIGINT, {0x8049d48, [INT], SA_RESTART|0x4000000}, {SIG_DFL}, 8) = 0 rt_sigaction(SIGTERM, {0x8049d48, [TERM], SA_RESTART|0x4000000}, {SIG_DFL}, 8) = 0 gettimeofday({1054302587, 143382}, NULL) = 0
ioctl(3, 0x2285, 0xbffff28c) = 0
gettimeofday({1054302587, 144030}, NULL) = 0
gettimeofday({1054302587, 144315}, NULL) = 0
ioctl(3, 0x2285, 0xbffff25c) = 0
gettimeofday({1054302587, 150267}, NULL) = 0
gettimeofday({1054302587, 150526}, NULL) = 0
ioctl(3, 0x2285, 0xbffff25c) = 0
gettimeofday({1054302587, 151355}, NULL) = 0
write(2, "Capacity: 49843 Blocks = 99686 k"..., 61Capacity: 49843 Blocks = 99686 kBytes = 97 MBytes = 102 prMB ) = 61
write(2, "Sectorsize: 2048 Bytes\n", 23Sectorsize: 2048 Bytes
) = 23
gettimeofday({1054302587, 152679}, NULL) = 0
ioctl(3, 0x2285, 0xbfffedfc) = 0
gettimeofday({1054302587, 156396}, NULL) = 0
gettimeofday({1054302587, 156644}, NULL) = 0
ioctl(3, 0x2285, 0xbfffec7c) = 0
...
...[snip]...
...
ioctl(3, 0x2285, 0xbfffefcc) = 0
gettimeofday({1054302587, 244917}, NULL) = 0
write(2, "Copy from SCSI (0,0,0) disk to f"..., 48Copy from SCSI (0,0,0) disk to file '/dev/null' ) = 48
open("/dev/null", O_WRONLY|O_CREAT|O_TRUNC|O_LARGEFILE, 0666) = 4
fcntl64(4, F_GETFL) = 0x8001 (flags O_WRONLY|O_LARGEFILE)
fstat64(4, {st_mode=S_IFCHR|0666, st_rdev=makedev(1, 3), ...}) = 0
ioctl(4, SNDCTL_TMR_TIMEBASE, 0xbfffedb8) = -1 ENOTTY (Inappropriate ioctl for device) old_mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40017000

_llseek(4, 0, [0], SEEK_CUR)            = 0
munmap(0x40017000, 4096)                = 0
write(2, "end:     49843\n", 15end:     49843

) = 15
gettimeofday({1054302587, 248522}, NULL) = 0
) = 232, "addr: 0 cnt: 48\r", 23addr: 0 cnt: 48
gettimeofday({1054302587, 249061}, NULL) = 0
ioctl(3, 0x2285, 0xbfffef6c) = 0
gettimeofday({1054302587, 259824}, NULL) = 0
write(2, "/opt/schily/bin/readcd: Success."..., 352/opt/schily/bin/readcd: Success. read_cd: scsi sendcmd: no error
CDB: BE 00 00 00 00 00 00 00 30 FA 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70
Sense Key: 0x0 No Additional Sense, Segment 0
Sense Code: 0x00 Qual 0x00 (no additional sense information) Fru 0x0
Sense flags: Blk 0 (not valid)
resid: 127008
cmd finished after 0.010s timeout 40s
) = 352
write(2, "/opt/schily/bin/readcd: Success."..., 57/opt/schily/bin/readcd: Success. Cannot read source disk ) = 57
write(2, "/opt/schily/bin/readcd: Retrying"..., 48/opt/schily/bin/readcd: Retrying from sector 0. ) = 48
write(2, ".", 1.) = 1
gettimeofday({1054302587, 262470}, NULL) = 0
ioctl(3, 0x2285, 0xbfffcf4c) = 0
gettimeofday({1054302587, 263143}, NULL) = 0
gettimeofday({1054302587, 263402}, NULL) = 0

Updated patch, please give that a shot. These sense_len wasn't being set correctly.

===== drivers/block/ioctl.c 1.54 vs edited =====

@@ -207,11 +207,8 @@
 		set_device_ro(bdev, n);
 		return 0;
 	default:
-		if (disk->fops->ioctl) {
-			ret = disk->fops->ioctl(inode, file, cmd, arg);
-			if (ret != -EINVAL)
-				return ret;
-		}
+		if (disk->fops->ioctl)
+			return disk->fops->ioctl(inode, file, cmd, arg);
 	}
 	return -ENOTTY;
 }

===== drivers/block/scsi_ioctl.c 1.27 vs edited =====

===== drivers/ide/ide-cd.c 1.46 vs edited =====

@@ -666,8 +666,10 @@
 		struct cdrom_info *info = drive->driver_data;
 		void *sense = &info->sense_data;
 		
-		if (failed && failed->sense)
+		if (failed && failed->sense) {
 			sense = failed->sense;
+			failed->sense_len = rq->sense_len;
+		}
 
 		cdrom_analyze_sense_data(drive, failed, sense);
 	}

@@ -723,7 +725,7 @@
 		 * scsi status byte
 		 */
 		if ((rq->flags & REQ_BLOCK_PC) && !rq->errors)
-			rq->errors = CHECK_CONDITION;
+			rq->errors = SAM_STAT_CHECK_CONDITION;
 
 		/* Check for tray open. */
 		if (sense_key == NOT_READY) {

@@ -1471,8 +1476,9 @@
 		/* Keep count of how much data we've moved. */
 		rq->data += thislen;
 		rq->data_len -= thislen;
-		if (rq->cmd[0] == GPCMD_REQUEST_SENSE)
-			rq->sense_len++;
+
+		if (rq->flags & REQ_SENSE)
+			rq->sense_len += thislen;
 	} else {
 confused:
 		printk ("%s: cdrom_pc_intr: The drive "

@@ -1609,10 +1615,18 @@
 
 static void post_transform_command(struct request *req)
 {
-	char *ibuf = req->buffer;
 	u8 *c = req->cmd;
+	char *ibuf;
 
 	if (!blk_pc_request(req))
+		return;
+
+	if (req->bio)
+		ibuf = bio_data(req->bio);
+	else
+		ibuf = req->data;
+
+	if (!ibuf)
 		return;
 
 	/*

===== fs/bio.c 1.45 vs edited =====

@@ -538,12 +538,6 @@
 	bio = __bio_map_user(bdev, uaddr, len, write_to_vm);
 
 	if (bio) {
-		if (bio->bi_size < len) {
-			bio_endio(bio, bio->bi_size, 0);
-			bio_unmap_user(bio, 0);
-			return NULL;
-		}
-
 		/*
 		 * subtle -- if __bio_map_user() ended up bouncing a bio,
 		 * it would normally disappear when its bi_end_io is run.

@@ -551,6 +545,12 @@
 		 * reference to it
 		 */
 		bio_get(bio);
+
+		if (bio->bi_size < len) {
+			bio_endio(bio, bio->bi_size, 0);
+			bio_unmap_user(bio, 0);
+			return NULL;
+		}
 	}
 
 	return bio;

Jens Axboe

Works fine for readcd and cdrecord (same with CD and DVD) now exits in another way.

regards
Markus

[plail@plailis_lfs]dvdrecord dev=/dev/hdb speed=4 -v -dao driveropts=burnfree -dummy /video-2/trailer_final_1000_dl.mov Cdrecord-ProDVD-Clone 2.01a12 (i586-pc-linux-gnu) Copyright (C) 1995-2003 Jörg Schilling Unlocked features: ProDVD Clone
Limited features: speed
This copy of cdrecord is licensed for: private/research/educational_non-commercial_use
TOC Type: 1 = CD-ROM
scsidev: '/dev/hdb'
devname: '/dev/hdb'
scsibus: -2 target: -2 lun: -2
Warning: Open by 'devname' is unintentional and not supported.
Linux sg driver version: 3.5.27
Using libscg version 'schily-0.7'
Driveropts: 'burnfree'
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'TEAC '
Identifikation : 'DV-W50E '
Revision : '1.30'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: DVD-RW sequential overwrite
Profile: DVD-RW sequential overwrite (current)
Profile: DVD-RW restricted overwrite (current)
Profile: DVD-R sequential recording (current)
Profile: DVD-ROM
Profile: CD-RW
Profile: CD-R
Profile: CD-ROM
Using generic SCSI-3/mmc-2 DVD-R/DVD-RW driver (mmc_dvd).
Driver flags : DVD MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1605632 = 1568 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 97 MB
Total size: 97 MB = 49843 sectors
Current Secsize: 2048
Total power on hours: 110150
Blocks total: 2298496 Blocks current: 2298496 Blocks remaining: 2248653
Starting to write CD/DVD at speed 2 in dummy SAO mode for single session.
Last chance to quit, starting dummy write 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is ON.

Starting new track at sector: 0
Track 01:    1 of   97 MB written (fifo  96%) [buf  67%]  10.5x.cdrecord-ProDVD: Success. write_g1: scsi sendcmd: no error
CDB:  2A 00 00 00 03 64 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0E 00 00 00 00 21 02 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x21 Qual 0x02 (invalid address for write) Fru 0x0
Sense flags: Blk 0 (not valid) 
resid: 63488

cmd finished after 0.006s timeout 100s

write track data: error after 1777664 bytes
cdrecord-ProDVD: The current problem looks like a buffer underrun.
cdrecord-ProDVD: It looks like 'driveropts=burnfree' does not work for this drive.
cdrecord-ProDVD: Please report.
cdrecord-ProDVD: Make sure that you are root, enable DMA and check your HW/OS set up.
Writing time: 46.904s
Average write speed 15.0x.
Fixating...
WARNING: Some drives don't like fixation in dummy mode.
Fixating time: 1.528s
cdrecord-ProDVD: fifo had 95 puts and 32 gets.
cdrecord-ProDVD: fifo was 0 times empty and 19 times full, min fill was 92%. You have new mail in /var/mail/plail
[18:49:09]-[Fri May 30]-[~]

[root@plailis_lfs]strace /opt/schily/bin/cdrecord dev=/dev/hdb speed=4 -v -dao driveropts=burnfree -dummy /video-2/trailer_final_1000_dl.mov execve("/opt/schily/bin/cdrecord", ["/opt/schily/bin/cdrecord", "dev=/dev/hdb", "speed=4", "-v", "-dao", "driveropts=burnfree", "-dummy", "/video-2/trailer_final_1000_dl.mov"], [/* 45 vars */]) = 0

brk(0)                                  = 0x8099000
open("/etc/ld.so.preload", O_RDONLY)    = -1 ENOENT (No such file or directory)
open("/etc/ld.so.cache", O_RDONLY)      = 3

fstat64(3, {st_mode=S_IFREG|0644, st_size=66034, ...}) = 0 old_mmap(NULL, 66034, PROT_READ, MAP_PRIVATE, 3, 0) = 0x40017000
close(3) = 0
open("/lib/libc.so.6", O_RDONLY) = 3
read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0\10\332"..., 1024) = 1024 fstat64(3, {st_mode=S_IFREG|0755, st_size=5021367, ...}) = 0 old_mmap(NULL, 1215588, PROT_READ|PROT_EXEC, MAP_PRIVATE, 3, 0) = 0x40028000 mprotect(0x40146000, 44132, PROT_NONE) = 0

old_mmap(0x40146000, 28672, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0x11d000) = 0x40146000
old_mmap(0x4014d000, 15460, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x4014d000
close(3)                                = 0
munmap(0x40017000, 66034)               = 0
getrlimit(0x7, 0xbfffcee4)              = 0
brk(0)                                  = 0x8099000
brk(0x8099180)                          = 0x8099180
brk(0x809a000)                          = 0x809a000

open("/etc/default/cdrecord", O_RDONLY) = -1 ENOENT (No such file or directory)
fstat64(1, {st_mode=S_IFCHR|0600, st_rdev=makedev(136, 0), ...}) = 0
old_mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40017000
write(1, "Cdrecord 2.01a15 (i686-pc-linux-"..., 76Cdrecord 2.01a15 (i686-pc-linux-gnu) Copyright (C) 1995-2003 Jörg Schilling ) = 76
fstat64(2, {st_mode=S_IFCHR|0600, st_rdev=makedev(136, 0), ...}) = 0

...
...[snip]
...

gettimeofday({1054313438, 700025}, NULL) = 0
ioctl(3, 0x2285, 0xbfffcd0c) = 0
gettimeofday({1054313438, 706685}, NULL) = 0
write(2, "/opt/schily/bin/cdrecord: Succes"..., 384/opt/schily/bin/cdrecord: Success. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 00 03 07 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0E 00 00 00 00 21 02 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x21 Qual 0x02 (invalid address for write) Fru 0x0
Sense flags: Blk 0 (not valid)
resid: 63488
cmd finished after 0.006s timeout 200s
) = 384
write(1, "\nwrite track data: error after 1"..., 45
write track data: error after 1587200 bytes
) = 45
write(2, "/opt/schily/bin/cdrecord: The cu"..., 76/opt/schily/bin/cdrecord: The current problem looks like a buffer underrun. ) = 76
write(2, "/opt/schily/bin/cdrecord: It loo"..., 92/opt/schily/bin/cdrecord: It looks like 'driveropts=burnfree' does not work for this drive. ) = 92
write(2, "/opt/schily/bin/cdrecord: Please"..., 41/opt/schily/bin/cdrecord: Please report.
) = 41
write(2, "/opt/schily/bin/cdrecord: Make s"..., 95/opt/schily/bin/cdrecord: Make sure that you are root, enable DMA and check your HW/OS set up. ) = 95
rt_sigprocmask(SIG_BLOCK, [CHLD], [RTMIN], 8) = 0

Hi all

I tested 2.5.70 with scsi-ioctl-2 patch

It works fine until It has to read the last sectors. I get the following messages from readcd, using different CD-Rs

agapito:~# readcd dev=/dev/hdc f=/dev/null
Read  speed:  8450 kB/s (CD  48x, DVD  6x).
Write speed:  7056 kB/s (CD  40x, DVD  5x).
Capacity: 353137 Blocks = 706274 kBytes = 689 MBytes = 723 prMB
Sectorsize: 2048 Bytes
Copy from SCSI (0,0,0) disk to file '/dev/null'
end:    353137
readcd: Success. read_g1: scsi sendcmd: no error
CDB:  28 00 00 05 63 5B 00 00 16 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 64 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x64 Qual 0x00 (illegal mode for this track) Fru 0x0
Sense flags: Blk 0 (not valid)
resid: 45056
cmd finished after 3.267s timeout 40s
readcd: Success. Cannot read source disk
readcd: Retrying from sector 353115.
.....................~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~
readcd: Success. Error on sector 353135 not corrected. Total of 1 errors.

Time total: 1094.406sec
Read 706230.00 kB at 645.3 kB/sec.

agapito:~# readcd dev=/dev/hdc f=/dev/null
Read  speed:  8450 kB/s (CD  48x, DVD  6x).
Write speed:  7056 kB/s (CD  40x, DVD  5x).
Capacity: 355841 Blocks = 711682 kBytes = 695 MBytes = 728 prMB
Sectorsize: 2048 Bytes
Copy from SCSI (0,0,0) disk to file '/dev/null'
end:    355841
readcd: Success. read_g1: scsi sendcmd: no error
CDB:  28 00 00 05 6D F0 00 00 11 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 64 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x64 Qual 0x00 (illegal mode for this track) Fru 0x0
Sense flags: Blk 0 (not valid)
resid: 34816
cmd finished after 2.965s timeout 40s
readcd: Success. Cannot read source disk
readcd: Retrying from sector 355824.
................~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~+~~~-~~~
readcd: Success. Error on sector 355839 not corrected. Total of 1 errors.

Time total: 1058.468sec
Read 711648.00 kB at 672.3 kB/sec.

dmesg shows several
hdc: confused, missing data
and then (sometimes)
cdrom_newpc_intr: 2048 residual after xfer
for each run of readcd

readcd version comes from

ulisses@agapito:~$ dpkg -l | grep cdrecord
ii  cdrecord       2.0+a14-1      A command line CD writing tool

the CDR/W recorder is not the best thing on this world...

agapito:~# cdrecord dev=/dev/hdc -checkdrive
Cdrecord 2.01a14 (i686-pc-linux-gnu) Copyright (C) 1995-2003 Jörg Schilling
scsidev: '/dev/hdc'
devname: '/dev/hdc'
scsibus: -2 target: -2 lun: -2
Warning: Open by 'devname' is unintentional and not supported.
Linux sg driver version: 3.5.27
Using libscg version 'schily-0.7'
Device type    : Removable CD-ROM
Version        : 0
Response Format: 1
Vendor_info    : 'Polaroid'
Identifikation : 'BurnMAX48       '
Revision       : '482E'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-2 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R

Can I do anything else?

Ulisses

Debian GNU/Linux: a dream come true
-----------------------------------------------------------------------------
"Computers are useless. They can only give answers." Pablo Picasso

---> Visita http://www.valux.org/ para saber acerca de la <---
---> Asociación Valenciana de Usuarios de Linux <---

This is just normal. Either the CD-Rs are burned in TAO mode or your writer has problems with DAO (mine has the same problems). See README.verify. Every such disc has two unreadable "run-out" sectors. If this happens with -dao, try -raw96r.

HTH
Markus

BTW: Can you successsfully burn CD-Rs with > 2.5.45? If so, could you send me your .config please?

Hi Markus

Ok, I previously read about it in README.copy but I did misunderstud it, thanks for your clarification

I never had problems burning successfully in TAO mode with kernel > 2.5.5X. Please note, I still have not used the writer in dao/raw96* mode (or don't remember). I included the config after the signature, It's a simple sis735 IDE system.

I have stabily problems in the system but I belive it's a graphic card problem (or heat that causes it)

I will report more about it when I make some copy

Ulisses

-----------------------------------------------------------------------------
"Computers are useless. They can only give answers." Pablo Picasso

---> Visita http://www.valux.org/ para saber acerca de la <---
---> Asociación Valenciana de Usuarios de Linux <---

this is 2.5.70scsi-ioctl-2

#
# Automatically generated make config: don't edit
#
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y

#
# General setup
#
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_EMBEDDED is not set
CONFIG_FUTEX=y
CONFIG_EPOLL=y

#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
# CONFIG_MODVERSIONS is not set
CONFIG_KMOD=y

#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
CONFIG_MK7=y
# CONFIG_MK8 is not set
# CONFIG_MELAN is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_USE_3DNOW=y
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_SMP is not set
CONFIG_PREEMPT=y
# CONFIG_X86_UP_APIC is not set
CONFIG_X86_TSC=y
# CONFIG_X86_MCE is not set
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
# CONFIG_X86_CPUID is not set
# CONFIG_EDD is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
CONFIG_HAVE_DEC_LOCK=y

#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
# CONFIG_SOFTWARE_SUSPEND is not set

#
# ACPI Support
#
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
# CONFIG_ACPI_AC is not set
# CONFIG_ACPI_BATTERY is not set
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
# CONFIG_ACPI_TOSHIBA is not set
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_BUS=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
# CONFIG_APM is not set

#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set

#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
# CONFIG_PCI_LEGACY_PROC is not set
CONFIG_PCI_NAMES=y
# CONFIG_ISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
# CONFIG_HOTPLUG is not set

#
# Executable file formats
#
CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not set
# CONFIG_BINFMT_AOUT is not set
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m

#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set

#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_CML1=m
# CONFIG_PARPORT_SERIAL is not set
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
# CONFIG_PARPORT_OTHER is not set
CONFIG_PARPORT_1284=y

#
# Plug and Play support
#
# CONFIG_PNP is not set

#
# Block devices
#
CONFIG_BLK_DEV_FD=m
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_LBD is not set

#
# ATA/ATAPI/MFM/RLL device support
#
CONFIG_IDE=y

#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y

#
# Please see Documentation/ide.txt for help/info on IDE drives #
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_IDEDISK_STROKE is not set CONFIG_BLK_DEV_IDECD=m
# CONFIG_BLK_DEV_IDEFLOPPY is not set CONFIG_BLK_DEV_IDESCSI=m
# CONFIG_IDE_TASK_IOCTL is not set

#
# IDE chipset support/bugfixes
#
# CONFIG_BLK_DEV_CMD640 is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDE_TCQ is not set
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
CONFIG_BLK_DEV_ADMA=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_RZ1000 is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
CONFIG_BLK_DEV_SIS5513=y
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_BLK_DEV_IDE_MODES=y

#
# SCSI device support
#
CONFIG_SCSI=m

#
# SCSI support type (disk, tape, CD-ROM)
#
# CONFIG_BLK_DEV_SD is not set
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=m

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs #
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_REPORT_LUNS is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set

#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set

#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set

#
# Fusion MPT device support
#

#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
# CONFIG_IEEE1394 is not set

#
# I2O device support
#
# CONFIG_I2O is not set

#
# Networking support
#
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
# CONFIG_NETLINK_DEV is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_INET_ECN is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set

#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_MAC=m
CONFIG_IP_NF_MATCH_PKTTYPE=m
CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH_ESP=m
CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_TCPMSS=m
CONFIG_IP_NF_MATCH_HELPER=m
CONFIG_IP_NF_MATCH_STATE=m
CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_MATCH_UNCLEAN=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_MIRROR=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_NAT_LOCAL=y
CONFIG_IP_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_NAT_AMANDA=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_MARK=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_COMPAT_IPCHAINS=m
CONFIG_IP_NF_COMPAT_IPFWADM=m
# CONFIG_IPV6 is not set
# CONFIG_XFRM_USER is not set

#
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_IPV6_SCTP__=y
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_LLC is not set
# CONFIG_DECNET is not set
# CONFIG_BRIDGE is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set

#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
CONFIG_NETDEVICES=y

#
# ARCnet devices
#
# CONFIG_ARCNET is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_ETHERTAP is not set

#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_MII is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set

#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_B44 is not set
# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
CONFIG_SIS900=y
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set

#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set

#
# Ethernet (10000 Mbit)
#
# CONFIG_IXGB is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set

#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set

#
# Token Ring devices (depends on LLC=y)
#
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set

#
# Wan interfaces
#
# CONFIG_WAN is not set

#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set

#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set

#
# ISDN subsystem
#
# CONFIG_ISDN_BOOL is not set

#
# Telephony Support
#
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=m
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set

#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
# CONFIG_SERIAL_8250_CONSOLE is not set
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
CONFIG_PRINTER=m
# CONFIG_LP_CONSOLE is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set

#
# I2C support
#
# CONFIG_I2C is not set

#
# I2C Hardware Sensors Mainboard support
#

#
# I2C Hardware Sensors Chip support
#
# CONFIG_I2C_SENSOR is not set

#
# Mice
#
# CONFIG_BUSMOUSE is not set
# CONFIG_QIC02_TAPE is not set

#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set

#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_NVRAM is not set
CONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set

#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=y
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_AMD_8151 is not set
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_NVIDIA is not set
CONFIG_AGP_SIS=y
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_VIA is not set
CONFIG_DRM=y
CONFIG_DRM_TDFX=y
# CONFIG_DRM_GAMMA is not set
# CONFIG_DRM_R128 is not set
# CONFIG_DRM_RADEON is not set
# CONFIG_DRM_MGA is not set
# CONFIG_MWAVE is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_HANGCHECK_TIMER is not set

#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set

#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set

#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
# CONFIG_EXT2_FS_POSIX_ACL is not set
# CONFIG_EXT2_FS_SECURITY is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
# CONFIG_ZISOFS is not set
CONFIG_UDF_FS=m

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
# CONFIG_NTFS_RW is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
# CONFIG_DEVFS_FS is not set
CONFIG_DEVPTS_FS=y
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
CONFIG_RAMFS=y

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set

#
# Network File Systems
#
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
CONFIG_NFSD_V4=y
# CONFIG_NFSD_TCP is not set
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_SUNRPC=m
# CONFIG_SUNRPC_GSS is not set
CONFIG_SMB_FS=m
# CONFIG_SMB_NLS_DEFAULT is not set
CONFIG_CIFS=m
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_INTERMEZZO_FS is not set
# CONFIG_AFS_FS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_SMB_NLS=y
CONFIG_NLS=y

#
# Native Language Support
#
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set

#
# Graphics support
#
# CONFIG_FB is not set
# CONFIG_VIDEO_SELECT is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y

#
# Sound
#
CONFIG_SOUND=y

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=y
CONFIG_SND_SEQUENCER=y
# CONFIG_SND_SEQ_DUMMY is not set
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set

#
# Generic devices
#
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set

#
# PCI devices
#
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
CONFIG_SND_INTEL8X0=y
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_VIA82XX is not set

#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set

#
# USB support
#
# CONFIG_USB is not set
# CONFIG_USB_GADGET is not set

#
# Bluetooth support
#
# CONFIG_BT is not set

#
# Profiling support
#
# CONFIG_PROFILING is not set

#
# Kernel hacking
#
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_KALLSYMS is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_FRAME_POINTER is not set

#
# Security options
#
CONFIG_SECURITY=y
# CONFIG_SECURITY_NETWORK is not set
# CONFIG_SECURITY_CAPABILITIES is not set
# CONFIG_SECURITY_ROOTPLUG is not set

#
# Cryptographic options
#
# CONFIG_CRYPTO is not set

#
# Library routines
#
# CONFIG_CRC32 is not set
CONFIG_X86_BIOS_REBOOT=y