USB: core: skip unconfiguration if device doesn't support it
Subsystems (2)
PATCH v4 1/1 USB: core: skip unconfiguration if device doesn't support it
Bluetooth Dongles with CSR chip (i.e. USB Bluetooth V4.0 Dongle by Trust) hang when they are unbound from 'unbind' sysfs entry and can not be bound again.
The reason is CSR chip hangs when usb configuration command with index 0 (used to unconfigure) is sent during disconnection.
To avoid this unwanted result, it is necessary not to send this command for CSR chip, so a new quirk has been created.
Athough device is not unconfigured, it is better to avoid device hanging to be able to operate. Even bluetooth can be previously turned off.
On the other hand, this is not important if usb device is going to be bound again (normal behavior), i.e. with usbip.
---
V3 -> V4:
- Reorder quirk entries to be in numerical order according to the vendor ID and product ID.
- Add patch version information.
V2 -> V3:
- Change subject (Bluetooth: btusb: CSR chip hangs when unbound ->
USB: core: skip unconfiguration if device doesn't support it).
- Improve quirk checking.
- Allow to test quirk interactively.
V1 -> V2:
- Use quirk feature for the exception.
Documentation/admin-guide/kernel-parameters.txt | 2 ++ drivers/usb/core/message.c | 12 +++++++++--- drivers/usb/core/quirks.c | 6 ++++++ include/linux/usb/quirks.h | 3 +++ 4 files changed, 20 insertions(+), 3 deletions(-)
Documentation/admin-guide/kernel-parameters.txt +2 -0
@@ -6183,6 +6183,8 @@ pause after every control message); o = USB_QUIRK_HUB_SLOW_RESET (Hub needs extra delay after resetting its port); + p = USB_QUIRK_SKIP_UNCONFIGURE (device doesn't + support unconfigure); Example: quirks=0781:5580:bk,0a5c:5834:gij usbhid.mousepoll=
drivers/usb/core/message.c +9 -3
@@ -2108,9 +2108,15 @@ int usb_set_configuration(struct usb_device *dev, int configuration) }kfree (new_interfaces); - ret =usb_control_msg_send (dev,0 ,USB_REQ_SET_CONFIGURATION ,0 , - configuration,0 ,NULL ,0 , -USB_CTRL_SET_TIMEOUT ,GFP_NOIO ); +if (configuration ==0 && !cp + && (dev->quirks &USB_QUIRK_SKIP_UNCONFIGURE )) { +dev_warn (&dev->dev,"device is not unconfigured!\n" ); + ret =0 ; + }else + ret =usb_control_msg_send (dev,0 ,USB_REQ_SET_CONFIGURATION ,0 , + configuration,0 ,NULL ,0 , +USB_CTRL_SET_TIMEOUT ,GFP_NOIO ); +if (ret && cp) {/* * All the old state is gone, so what else can we do?
drivers/usb/core/quirks.c +6 -0
@@ -138,6 +138,9 @@ static int quirks_param_set(const char *value, const struct kernel_param *kp)case 'o' : flags |=USB_QUIRK_HUB_SLOW_RESET ;break ; +case 'p' : + flags |=USB_QUIRK_SKIP_UNCONFIGURE ; +break ;/* Ignore unrecognized flag characters */ } }
@@ -394,6 +397,9 @@ static const struct usb_device_id usb_quirk_list[] = {/* ELMO L-12F document camera */ { USB_DEVICE(0x09a1, 0x0028), .driver_info = USB_QUIRK_DELAY_CTRL_MSG }, + /* CSR Bluetooth */ + { USB_DEVICE(0x0a12, 0x0001), .driver_info = USB_QUIRK_SKIP_UNCONFIGURE }, + /* Broadcom BCM92035DGROM BT dongle */ { USB_DEVICE(0x0a5c, 0x2021), .driver_info = USB_QUIRK_RESET_RESUME },
include/linux/usb/quirks.h +3 -0
@@ -72,4 +72,7 @@/* device has endpoints that should be ignored */ #define USB_QUIRK_ENDPOINT_IGNORE BIT(15) +/* device doesn't support unconfigure. */ +#define USB_QUIRK_SKIP_UNCONFIGURE BIT(16) +#endif /* __LINUX_USB_QUIRKS_H */
Signature · 1 line
2.35.1
Hi Jose,
Quoted 87 lines
Bluetooth Dongles with CSR chip (i.e. USB Bluetooth V4.0 Dongle by Trust) hang when they are unbound from 'unbind' sysfs entry and can not be bound again.
The reason is CSR chip hangs when usb configuration command with index 0 (used to unconfigure) is sent during disconnection.
To avoid this unwanted result, it is necessary not to send this command for CSR chip, so a new quirk has been created.
Athough device is not unconfigured, it is better to avoid device hanging to be able to operate. Even bluetooth can be previously turned off.
On the other hand, this is not important if usb device is going to be bound again (normal behavior), i.e. with usbip.Signed-off-by Jose Ignacio Tornos Martinez <[email protected]>---
V3 -> V4:
- Reorder quirk entries to be in numerical order according to the vendor ID and product ID.
- Add patch version information.
V2 -> V3:
- Change subject (Bluetooth: btusb: CSR chip hangs when unbound ->
USB: core: skip unconfiguration if device doesn't support it).
- Improve quirk checking.
- Allow to test quirk interactively.
V1 -> V2:
- Use quirk feature for the exception.Documentation/admin-guide/kernel-parameters.txt | 2 ++ drivers/usb/core/message.c | 12 +++++++++--- drivers/usb/core/quirks.c | 6 ++++++ include/linux/usb/quirks.h | 3 +++ 4 files changed, 20 insertions(+), 3 deletions(-)Documentation/admin-guide/kernel-parameters.txt +2
-0@@ -6183,6 +6183,8 @@ pause after every control message); o = USB_QUIRK_HUB_SLOW_RESET (Hub needs extra delay after resetting its port); + p = USB_QUIRK_SKIP_UNCONFIGURE (device doesn't + support unconfigure); Example: quirks=0781:5580:bk,0a5c:5834:gij usbhid.mousepoll=drivers/usb/core/message.c +9
-3@@ -2108,9 +2108,15 @@ int usb_set_configuration(struct usb_device *dev, int configuration) }kfree (new_interfaces); - ret =usb_control_msg_send (dev,0 ,USB_REQ_SET_CONFIGURATION ,0 , - configuration,0 ,NULL ,0 , -USB_CTRL_SET_TIMEOUT ,GFP_NOIO ); +if (configuration ==0 && !cp + && (dev->quirks &USB_QUIRK_SKIP_UNCONFIGURE )) { +dev_warn (&dev->dev,"device is not unconfigured!\n" ); + ret =0 ; + }else + ret =usb_control_msg_send (dev,0 ,USB_REQ_SET_CONFIGURATION ,0 , + configuration,0 ,NULL ,0 , +USB_CTRL_SET_TIMEOUT ,GFP_NOIO ); +if (ret && cp) {/* * All the old state is gone, so what else can we do? drivers/usb/core/quirks.c +3
-0@@ -138,6 +138,9 @@ static int quirks_param_set(const char *value, const struct kernel_param *kp)case 'o' : flags |=USB_QUIRK_HUB_SLOW_RESET ;break ; +case 'p' : + flags |=USB_QUIRK_SKIP_UNCONFIGURE ; +break ;/* Ignore unrecognized flag characters */ } }
drivers/usb/core/quirks.c static const struct usb_device_id usb_quirk_list[] = { · line 402
Quoted 6 lines
drivers/usb/core/quirks.c +3
-0@@ -394,6 +397,9 @@ static const struct usb_device_id usb_quirk_list[] = {/* ELMO L-12F document camera */ { USB_DEVICE(0x09a1, 0x0028), .driver_info = USB_QUIRK_DELAY_CTRL_MSG }, + /* CSR Bluetooth */ + { USB_DEVICE(0x0a12, 0x0001), .driver_info = USB_QUIRK_SKIP_UNCONFIGURE }, +
NAK. I said this before.
The VID:PID 0a12:0001 is used in millions of products that work correctly. Only because some counterfeit products get things wrong doesn’t mean all get marked as broken.
Regards
Marcel
Hello Marcel,
Ok, I am not sure if it is working in other related products ... Would it be ok if we keep the possibility to use the quirk if necessary? That is, by default CSR devices are not marked with the quirk but they can be marked by the users if necessary.
Thanks
Best regards
José Ignacio
Quoted 107 lines · Marcel Holtmann
Hi Jose,
Quoted 87 lines
Bluetooth Dongles with CSR chip (i.e. USB Bluetooth V4.0 Dongle by Trust) hang when they are unbound from 'unbind' sysfs entry and can not be bound again.
The reason is CSR chip hangs when usb configuration command with index 0 (used to unconfigure) is sent during disconnection.
To avoid this unwanted result, it is necessary not to send this command for CSR chip, so a new quirk has been created.
Athough device is not unconfigured, it is better to avoid device hanging to be able to operate. Even bluetooth can be previously turned off.
On the other hand, this is not important if usb device is going to be bound again (normal behavior), i.e. with usbip.Signed-off-by Jose Ignacio Tornos Martinez <[email protected]>---
V3 -> V4:
- Reorder quirk entries to be in numerical order according to the vendor ID and product ID.
- Add patch version information.
V2 -> V3:
- Change subject (Bluetooth: btusb: CSR chip hangs when unbound ->
USB: core: skip unconfiguration if device doesn't support it).
- Improve quirk checking.
- Allow to test quirk interactively.
V1 -> V2:
- Use quirk feature for the exception.Documentation/admin-guide/kernel-parameters.txt | 2 ++ drivers/usb/core/message.c | 12 +++++++++--- drivers/usb/core/quirks.c | 6 ++++++ include/linux/usb/quirks.h | 3 +++ 4 files changed, 20 insertions(+), 3 deletions(-)Documentation/admin-guide/kernel-parameters.txt +2
-0@@ -6183,6 +6183,8 @@ pause after every control message); o = USB_QUIRK_HUB_SLOW_RESET (Hub needs extra delay after resetting its port); + p = USB_QUIRK_SKIP_UNCONFIGURE (device doesn't + support unconfigure); Example: quirks=0781:5580:bk,0a5c:5834:gij usbhid.mousepoll=drivers/usb/core/message.c +9
-3@@ -2108,9 +2108,15 @@ int usb_set_configuration(struct usb_device *dev, int configuration) }kfree (new_interfaces); - ret =usb_control_msg_send (dev,0 ,USB_REQ_SET_CONFIGURATION ,0 , - configuration,0 ,NULL ,0 , -USB_CTRL_SET_TIMEOUT ,GFP_NOIO ); +if (configuration ==0 && !cp + && (dev->quirks &USB_QUIRK_SKIP_UNCONFIGURE )) { +dev_warn (&dev->dev,"device is not unconfigured!\n" ); + ret =0 ; + }else + ret =usb_control_msg_send (dev,0 ,USB_REQ_SET_CONFIGURATION ,0 , + configuration,0 ,NULL ,0 , +USB_CTRL_SET_TIMEOUT ,GFP_NOIO ); +if (ret && cp) {/* * All the old state is gone, so what else can we do? drivers/usb/core/quirks.c +3
-0@@ -138,6 +138,9 @@ static int quirks_param_set(const char *value, const struct kernel_param *kp)case 'o' : flags |=USB_QUIRK_HUB_SLOW_RESET ;break ; +case 'p' : + flags |=USB_QUIRK_SKIP_UNCONFIGURE ; +break ;/* Ignore unrecognized flag characters */ } }drivers/usb/core/quirks.c static const struct usb_device_id usb_quirk_list[] = { · line 402
Quoted 6 lines
drivers/usb/core/quirks.c +3
-0@@ -394,6 +397,9 @@ static const struct usb_device_id usb_quirk_list[] = {/* ELMO L-12F document camera */ { USB_DEVICE(0x09a1, 0x0028), .driver_info = USB_QUIRK_DELAY_CTRL_MSG }, + /* CSR Bluetooth */ + { USB_DEVICE(0x0a12, 0x0001), .driver_info = USB_QUIRK_SKIP_UNCONFIGURE }, +NAK. I said this before.
The VID:PID 0a12:0001 is used in millions of products that work correctly. Only because some counterfeit products get things wrong doesn’t mean all get marked as broken.
Regards
Marcel
Quoted 5 lines · Marcel Holtmann
Quoted 5 lines
drivers/usb/core/quirks.c +0
-0@@ -394,6 +397,9 @@ static const struct usb_device_id usb_quirk_list[] = {/* ELMO L-12F document camera */ { USB_DEVICE(0x09a1, 0x0028), .driver_info = USB_QUIRK_DELAY_CTRL_MSG },
Quoted 9 lines
drivers/usb/core/quirks.c static const struct usb_device_id usb_quirk_list[] = { · line 402
Quoted 3 lines
drivers/usb/core/quirks.c +3
-0+/* CSR Bluetooth */ + { USB_DEVICE(0x0a12, 0x0001), .driver_info = USB_QUIRK_SKIP_UNCONFIGURE }, +NAK. I said this before.
The VID:PID 0a12:0001 is used in millions of products that work correctly. Only because some counterfeit products get things wrong doesn’t mean all get marked as broken.
Hi,
if I may ask, how certain is that? Soft unbinding is probably not a common operation.
Regards
Oliver
Hello Oliver,
Of course, I am working with usbip to remotize usb devices, that is the reason why unbind/bind is needed and with the btusb devices that I have, it was not working.
Best regards
José Ignacio
Quoted 27 lines · Oliver Neukum
Quoted 5 lines · Marcel Holtmann
Quoted 5 lines
drivers/usb/core/quirks.c +0
-0@@ -394,6 +397,9 @@ static const struct usb_device_id usb_quirk_list[] = {/* ELMO L-12F document camera */ { USB_DEVICE(0x09a1, 0x0028), .driver_info = USB_QUIRK_DELAY_CTRL_MSG },Quoted 9 lines
drivers/usb/core/quirks.c static const struct usb_device_id usb_quirk_list[] = { · line 402
Quoted 3 lines
drivers/usb/core/quirks.c +3
-0+/* CSR Bluetooth */ + { USB_DEVICE(0x0a12, 0x0001), .driver_info = USB_QUIRK_SKIP_UNCONFIGURE }, +NAK. I said this before.
The VID:PID 0a12:0001 is used in millions of products that work correctly. Only because some counterfeit products get things wrong doesn’t mean all get marked as broken.
Hi,
if I may ask, how certain is that? Soft unbinding is probably not a common operation.
Regards
Oliver
Quoted 7 lines · Jose Ignacio Tornos Martinez
Hello Oliver,
Of course, I am working with usbip to remotize usb devices, that is the reason why unbind/bind is needed and with the btusb devices that I have, it was not working.
Hi,
sorry for being unclear. I was not referring to positive knowledge about the devices you are testing with. I was having dark thoughts about the other devices they are sharing an ID with.
But Bjorn's testing has resolved that. In that case we can indeed not penalize the compliant devices for the broken ones.
One question, though. Your approach of simply doing nothing if config 0 is to be selected again is a bit brutal. Have you considered resetting the device and stopping the reenumeration right as a config is supposed to be chosen?
Regards
Oliver
Hello Oliver,
No worries, as you said, Bjorn has provided a perfect test.
Yes, I have considered but I have thought that a clean and fast solution is enough, that is, suspending everything from the driver, because a new configuration is going to be applied when binding again from local or remote.
Device reset may have other implications and as you commented soft unbinding is not a common operation at least without binding again.
Best regards
José Ignacio
Quoted 31 lines · Oliver Neukum
Quoted 7 lines · Jose Ignacio Tornos Martinez
Hello Oliver,
Of course, I am working with usbip to remotize usb devices, that is the reason why unbind/bind is needed and with the btusb devices that I have, it was not working.
Hi,
sorry for being unclear. I was not referring to positive knowledge about the devices you are testing with. I was having dark thoughts about the other devices they are sharing an ID with.
But Bjorn's testing has resolved that. In that case we can indeed not penalize the compliant devices for the broken ones.One question, though. Your approach of simply doing nothing if config 0 is to be selected again is a bit brutal. Have you considered resetting the device and stopping the reenumeration right as a config is supposed to be chosen?
Regards
Oliver
Quoted 11 lines · Oliver Neukum
Quoted 10 lines · Marcel Holtmann
drivers/usb/core/quirks.c static const struct usb_device_id usb_quirk_list[] = { · line 402
Quoted 8 lines
drivers/usb/core/quirks.c +3
-0@@ -394,6 +397,9 @@ static const struct usb_device_id usb_quirk_list[] = {/* ELMO L-12F document camera */ { USB_DEVICE(0x09a1, 0x0028), .driver_info = USB_QUIRK_DELAY_CTRL_MSG }, + /* CSR Bluetooth */ + { USB_DEVICE(0x0a12, 0x0001), .driver_info = USB_QUIRK_SKIP_UNCONFIGURE }, +NAK. I said this before.
Quoted 8 lines
Quoted 4 lines
The VID:PID 0a12:0001 is used in millions of products that work correctly. Only because some counterfeit products get things wrong doesn’t mean all get marked as broken.
Hi,
if I may ask, how certain is that?
100%. Just get a real CSR device and try it.
canardo:/tmp# sed -ne '/ Port=07 /,/^$/p' /sys/kernel/debug/usb/devices T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=05 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a12 ProdID=0001 Rev=88.91 C:* #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
canardo:/tmp# hciconfig hci0
hci0: Type: Primary Bus: USB
BD Address: 00:1A:7D:DA:71:15 ACL MTU: 310:10 SCO MTU: 64:8
UP RUNNING
RX bytes:660 acl:0 sco:0 events:43 errors:0
TX bytes:2178 acl:0 sco:0 commands:43 errors:0canardo:/tmp# ls -l /sys/bus/usb/drivers/btusb/ total 0 lrwxrwxrwx 1 root root 0 May 5 13:23 1-8:1.0 -> ../../../../devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.0 lrwxrwxrwx 1 root root 0 May 5 13:23 1-8:1.1 -> ../../../../devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.1 --w------- 1 root root 4096 May 5 13:23 bind lrwxrwxrwx 1 root root 0 May 5 13:22 module -> ../../../../module/btusb -rw-r--r-- 1 root root 4096 May 5 13:22 new_id -rw-r--r-- 1 root root 4096 May 5 13:22 remove_id --w------- 1 root root 4096 May 5 13:22 uevent --w------- 1 root root 4096 May 5 13:23 unbind
canardo:/tmp# echo 1-8:1.0 > /sys/bus/usb/drivers/btusb/unbind canardo:/tmp# sed -ne '/ Port=07 /,/^$/p' /sys/kernel/debug/usb/devices T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=05 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a12 ProdID=0001 Rev=88.91 C:* #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
canardo:/tmp# hciconfig hci0 Can't get device info: No such device canardo:/tmp# ls -l /sys/bus/usb/drivers/btusb/ total 0 --w------- 1 root root 4096 May 5 13:23 bind lrwxrwxrwx 1 root root 0 May 5 13:22 module -> ../../../../module/btusb -rw-r--r-- 1 root root 4096 May 5 13:22 new_id -rw-r--r-- 1 root root 4096 May 5 13:22 remove_id --w------- 1 root root 4096 May 5 13:22 uevent --w------- 1 root root 4096 May 5 13:26 unbind
canardo:/tmp# echo 1-8:1.0 > /sys/bus/usb/drivers/btusb/bind canardo:/tmp# sed -ne '/ Port=07 /,/^$/p' /sys/kernel/debug/usb/devices T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=05 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a12 ProdID=0001 Rev=88.91 C:* #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
canardo:/tmp# hciconfig hci0
hci0: Type: Primary Bus: USB
BD Address: 00:1A:7D:DA:71:15 ACL MTU: 310:10 SCO MTU: 64:8
UP RUNNING
RX bytes:660 acl:0 sco:0 events:43 errors:0
TX bytes:2178 acl:0 sco:0 commands:43 errors:0canardo:/tmp# ls -l /sys/bus/usb/drivers/btusb/ total 0 lrwxrwxrwx 1 root root 0 May 5 13:27 1-8:1.0 -> ../../../../devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.0 lrwxrwxrwx 1 root root 0 May 5 13:27 1-8:1.1 -> ../../../../devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.1 --w------- 1 root root 4096 May 5 13:27 bind lrwxrwxrwx 1 root root 0 May 5 13:22 module -> ../../../../module/btusb -rw-r--r-- 1 root root 4096 May 5 13:22 new_id -rw-r--r-- 1 root root 4096 May 5 13:22 remove_id --w------- 1 root root 4096 May 5 13:22 uevent --w------- 1 root root 4096 May 5 13:26 unbind
I do have a couple of fake ones too. They are mostly interesting from a "why the h... would anyone do that?" perspective
Bjørn
Quoted 17 lines · Bjørn Mork
Quoted 16 lines · Oliver Neukum
Quoted 14 lines · Marcel Holtmann
drivers/usb/core/quirks.c static const struct usb_device_id usb_quirk_list[] = { · line 402
Quoted 8 lines
drivers/usb/core/quirks.c +3
-0@@ -394,6 +397,9 @@ static const struct usb_device_id usb_quirk_list[] = {/* ELMO L-12F document camera */ { USB_DEVICE(0x09a1, 0x0028), .driver_info = USB_QUIRK_DELAY_CTRL_MSG }, + /* CSR Bluetooth */ + { USB_DEVICE(0x0a12, 0x0001), .driver_info = USB_QUIRK_SKIP_UNCONFIGURE }, +NAK. I said this before.
The VID:PID 0a12:0001 is used in millions of products that work correctly. Only because some counterfeit products get things wrong doesn’t mean all get marked as broken.
Quoted 5 lines
Quoted 3 lines
Hi,
if I may ask, how certain is that?
100%. Just get a real CSR device and try it.
Please pardon me for butting in, but I don't see how this tests the condition that Jose is worried about.
You start with the device being configured and working:
Quoted 41 lines
canardo:/tmp# sed -ne '/ Port=07 /,/^$/p' /sys/kernel/debug/usb/devices T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=05 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a12 ProdID=0001 Rev=88.91 C:* #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1mscanardo:/tmp# hciconfig hci0 hci0: Type: Primary Bus: USB BD Address: 00:1A:7D:DA:71:15 ACL MTU: 310:10 SCO MTU: 64:8 UP RUNNING RX bytes:660 acl:0 sco:0 events:43 errors:0 TX bytes:2178 acl:0 sco:0 commands:43 errors:0canardo:/tmp# ls -l /sys/bus/usb/drivers/btusb/ total 0 lrwxrwxrwx 1 root root 0 May 5 13:23 1-8:1.0 -> ../../../../devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.0 lrwxrwxrwx 1 root root 0 May 5 13:23 1-8:1.1 -> ../../../../devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.1 --w------- 1 root root 4096 May 5 13:23 bind lrwxrwxrwx 1 root root 0 May 5 13:22 module -> ../../../../module/btusb
Review
Quoted 4 lines
(quoted diff) +0
-4-rw-r--r-- 1 root root 4096 May 5 13:22 new_id -rw-r--r-- 1 root root 4096 May 5 13:22 remove_id --w------- 1 root root 4096 May 5 13:22 uevent --w------- 1 root root 4096 May 5 13:23 unbind
Then you unbind the Bluetooth driver:
Quoted 1 line
canardo:/tmp# echo 1-8:1.0 > /sys/bus/usb/drivers/btusb/unbind
But the device is still configured, as proved by the fact that there is a '*' following the "C:" below:
Quoted 19 lines
canardo:/tmp# sed -ne '/ Port=07 /,/^$/p' /sys/kernel/debug/usb/devices T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=05 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a12 ProdID=0001 Rev=88.91 C:* #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
Quoted 8 lines
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Of course, since the btusb driver isn't bound, there is no corresponding Bluetooth interface in the kernel:
Review
Quoted 10 lines
canardo:/tmp# hciconfig hci0 Can't get device info: No such device canardo:/tmp# ls -l /sys/bus/usb/drivers/btusb/ total 0 --w------- 1 root root 4096 May 5 13:23 bind lrwxrwxrwx 1 root root 0 May 5 13:22 module -> ../../../../module/btusb(quoted diff) +0
-4-rw-r--r-- 1 root root 4096 May 5 13:22 new_id -rw-r--r-- 1 root root 4096 May 5 13:22 remove_id --w------- 1 root root 4096 May 5 13:22 uevent --w------- 1 root root 4096 May 5 13:26 unbind
Then you rebind the driver:
Quoted 42 lines
canardo:/tmp# echo 1-8:1.0 > /sys/bus/usb/drivers/btusb/bind canardo:/tmp# sed -ne '/ Port=07 /,/^$/p' /sys/kernel/debug/usb/devices T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=05 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a12 ProdID=0001 Rev=88.91 C:* #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1mscanardo:/tmp# hciconfig hci0 hci0: Type: Primary Bus: USB BD Address: 00:1A:7D:DA:71:15 ACL MTU: 310:10 SCO MTU: 64:8 UP RUNNING RX bytes:660 acl:0 sco:0 events:43 errors:0 TX bytes:2178 acl:0 sco:0 commands:43 errors:0canardo:/tmp# ls -l /sys/bus/usb/drivers/btusb/ total 0 lrwxrwxrwx 1 root root 0 May 5 13:27 1-8:1.0 -> ../../../../devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.0 lrwxrwxrwx 1 root root 0 May 5 13:27 1-8:1.1 -> ../../../../devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.1 --w------- 1 root root 4096 May 5 13:27 bind lrwxrwxrwx 1 root root 0 May 5 13:22 module -> ../../../../module/btusb
Review
Quoted 4 lines
(quoted diff) +0
-4-rw-r--r-- 1 root root 4096 May 5 13:22 new_id -rw-r--r-- 1 root root 4096 May 5 13:22 remove_id --w------- 1 root root 4096 May 5 13:22 uevent --w------- 1 root root 4096 May 5 13:26 unbind
And presumably the device is working again. However, none of this shows what happens when the device is unconfigured. To test that, you would have to do:
echo 0 >/sys/bus/usb/devices/1-8/bConfigurationValue echo 1 >/sys/bus/usb/devices/1-8/bConfigurationValue
and then see if the device continues to work.
Alan Stern
Quoted 6 lines
I do have a couple of fake ones too. They are mostly interesting from a "why the h... would anyone do that?" perspective
Bjørn
Quoted 2 lines · Alan Stern
Please pardon me for butting in, but I don't see how this tests the condition that Jose is worried about.
..
Quoted 8 lines
And presumably the device is working again. However, none of this shows what happens when the device is unconfigured. To test that, you would have to do:
echo 0 >/sys/bus/usb/devices/1-8/bConfigurationValue echo 1 >/sys/bus/usb/devices/1-8/bConfigurationValue
and then see if the device continues to work.
Ah, sorry. Scanned briefly, saw "bind", and assumed too much. Making an ass out of... you know.
Actually I didn't understand the part about unconfiguration since I can't see how that would happen during normal usage? Anyway, unconfiguring also works for me:
canardo:/tmp# hciconfig hci0
hci0: Type: Primary Bus: USB
BD Address: 00:1A:7D:DA:71:15 ACL MTU: 310:10 SCO MTU: 64:8
UP RUNNING
RX bytes:660 acl:0 sco:0 events:43 errors:0
TX bytes:2178 acl:0 sco:0 commands:43 errors:0canardo:/tmp# echo 0 >/sys/bus/usb/devices/1-8/bConfigurationValue canardo:/tmp# hciconfig hci0 Can't get device info: No such device canardo:/tmp# echo 1 >/sys/bus/usb/devices/1-8/bConfigurationValue
Not entirely sure how to validate that "everything" works at this point? I can use the rfcomm session the adapter usually handles and also run lescan after this. So I guess both BLE and BDR works.
And the counters count something:
canardo:/tmp# hciconfig hci0
hci0: Type: Primary Bus: USB
BD Address: 00:1A:7D:DA:71:15 ACL MTU: 310:10 SCO MTU: 64:8
UP RUNNING
RX bytes:3883 acl:40 sco:0 events:81 errors:0
TX bytes:2518 acl:19 sco:0 commands:50 errors:0I can see an error like this logged every time I unconfigure the device:
Bluetooth: hci0: urb 00000000e66a2492 failed to resubmit (2)
There is nothing else logged in kernel log
Bjørn
Hello,
Just repeating the same sequence here without the patch:
$ hciconfig
hci0: Type: Primary Bus: USB
BD Address: 00:1A:7D:DA:71:13 ACL MTU: 310:10 SCO MTU: 64:8
UP RUNNING
RX bytes:696 acl:0 sco:0 events:49 errors:0
TX bytes:3168 acl:0 sco:0 commands:49 errors:0
$
< scanning is working from Bluetooth Settings from GNOME >
$ echo 0 >/sys/bus/usb/devices/1-3/bConfigurationValue
$ hciconfig
$
< bluetooth device is not found in Bluetooth Settings from GNOME >
$ echo 1 >/sys/bus/usb/devices/1-3/bConfigurationValue
< it takes a while>
bash: echo: write error: Connection timed out
$ hciconfig
$
< bluetooth device is not found in Bluetooth Settings from GNOME >Definitely, Bjorn, your device is working better than mine.
And the same sequence with the patch, to show that it is working:
$ cat /proc/cmdline
BOOT_IMAGE=... usbcore.quirks=0a12:0001:p
$ cat /sys/module/usbcore/parameters/quirks
0a12:0001:p
$ hciconfig
hci0: Type: Primary Bus: USB
BD Address: 00:1A:7D:DA:71:13 ACL MTU: 310:10 SCO MTU: 64:8
UP RUNNING
RX bytes:806 acl:0 sco:0 events:66 errors:0
TX bytes:5168 acl:0 sco:0 commands:65 errors:0
$
< scanning is working from Bluetooth Settings from GNOME >
$ echo 0 >/sys/bus/usb/devices/1-3/bConfigurationValue
$ hciconfig
$
< bluetooth device is not found in Bluetooth Settings from GNOME >
$ echo 1 >/sys/bus/usb/devices/1-3/bConfigurationValue
$ hciconfig
hci0: Type: Primary Bus: USB
BD Address: 00:1A:7D:DA:71:13 ACL MTU: 310:10 SCO MTU: 64:8
UP RUNNING
RX bytes:696 acl:0 sco:0 events:49 errors:0
TX bytes:3168 acl:0 sco:0 commands:49 errors:0
$
< scanning is working from Bluetooth Settings from GNOME >In both cases, I also see similar log errors: Bluetooth: hci0: urb 00000000exxxxxxx failed to resubmit (2)
Best regards
José Ignacio
Quoted 58 lines · Bjørn Mork
Quoted 2 lines · Alan Stern
Please pardon me for butting in, but I don't see how this tests the condition that Jose is worried about.
..
Quoted 8 lines
And presumably the device is working again. However, none of this shows what happens when the device is unconfigured. To test that, you would have to do:
echo 0 >/sys/bus/usb/devices/1-8/bConfigurationValue echo 1 >/sys/bus/usb/devices/1-8/bConfigurationValue
and then see if the device continues to work.
Ah, sorry. Scanned briefly, saw "bind", and assumed too much. Making an ass out of... you know.
Actually I didn't understand the part about unconfiguration since I can't see how that would happen during normal usage? Anyway, unconfiguring also works for me:
canardo:/tmp# hciconfig hci0 hci0: Type: Primary Bus: USB BD Address: 00:1A:7D:DA:71:15 ACL MTU: 310:10 SCO MTU: 64:8 UP RUNNING RX bytes:660 acl:0 sco:0 events:43 errors:0 TX bytes:2178 acl:0 sco:0 commands:43 errors:0canardo:/tmp# echo 0 >/sys/bus/usb/devices/1-8/bConfigurationValue canardo:/tmp# hciconfig hci0 Can't get device info: No such device canardo:/tmp# echo 1 >/sys/bus/usb/devices/1-8/bConfigurationValueNot entirely sure how to validate that "everything" works at this point? I can use the rfcomm session the adapter usually handles and also run lescan after this. So I guess both BLE and BDR works.
And the counters count something:
canardo:/tmp# hciconfig hci0 hci0: Type: Primary Bus: USB BD Address: 00:1A:7D:DA:71:15 ACL MTU: 310:10 SCO MTU: 64:8 UP RUNNING RX bytes:3883 acl:40 sco:0 events:81 errors:0 TX bytes:2518 acl:19 sco:0 commands:50 errors:0I can see an error like this logged every time I unconfigure the device:
Bluetooth: hci0: urb
00000000e66a2492failed to resubmit (2)There is nothing else logged in kernel log
Bjørn
Quoted 12 lines · Bjørn Mork
Quoted 2 lines · Alan Stern
Please pardon me for butting in, but I don't see how this tests the condition that Jose is worried about.
..
Quoted 7 lines
And presumably the device is working again. However, none of this shows what happens when the device is unconfigured. To test that, you would have to do:
echo 0 >/sys/bus/usb/devices/1-8/bConfigurationValue echo 1 >/sys/bus/usb/devices/1-8/bConfigurationValue
Quoted 7 lines
Quoted 1 line
and then see if the device continues to work.
Ah, sorry. Scanned briefly, saw "bind", and assumed too much. Making an ass out of... you know.
Actually I didn't understand the part about unconfiguration since I can't see how that would happen during normal usage? Anyway,
Jose was exporting his device over usbip, which perhaps does not count as "normal" usage.
Quoted 9 lines
unconfiguring also works for me:
canardo:/tmp# hciconfig hci0 hci0: Type: Primary Bus: USB BD Address: 00:1A:7D:DA:71:15 ACL MTU: 310:10 SCO MTU: 64:8 UP RUNNING RX bytes:660 acl:0 sco:0 events:43 errors:0 TX bytes:2178 acl:0 sco:0 commands:43 errors:0
Quoted 7 lines
canardo:/tmp# echo 0 >/sys/bus/usb/devices/1-8/bConfigurationValue canardo:/tmp# hciconfig hci0 Can't get device info: No such device canardo:/tmp# echo 1 >/sys/bus/usb/devices/1-8/bConfigurationValueNot entirely sure how to validate that "everything" works at this point?
If it weren't, you would know. Error messages would have shown up at this point.
Quoted 13 lines
I can use the rfcomm session the adapter usually handles and also run lescan after this. So I guess both BLE and BDR works.
And the counters count something:
canardo:/tmp# hciconfig hci0 hci0: Type: Primary Bus: USB BD Address: 00:1A:7D:DA:71:15 ACL MTU: 310:10 SCO MTU: 64:8 UP RUNNING RX bytes:3883 acl:40 sco:0 events:81 errors:0 TX bytes:2518 acl:19 sco:0 commands:50 errors:0
Quoted 3 lines
I can see an error like this logged every time I unconfigure the device:
Bluetooth: hci0: urb
00000000e66a2492failed to resubmit (2)
That's normal. The driver probably could avoid giving that error message under these circumstances, but it's not a big deal.
Quoted 1 line
There is nothing else logged in kernel log
Okay, thanks for testing.
Alan Stern