freescale_p1010rdb_pa_defconfig: remove board

index f76e53b..a84bf63 100644
@@ -123,7 +123,6 @@ freescale_imx6sxsabresd_defconfig: *defconfig
 freescale_imx6ulevk_defconfig: *defconfig
 freescale_imx7dsabresd_defconfig: *defconfig
 freescale_mpc8315erdb_defconfig: *defconfig
-freescale_p1010rdb_pa_defconfig: *defconfig
 friendlyarm_nanopi_a64_defconfig: *defconfig
 friendlyarm_nanopi_neo2_defconfig: *defconfig
 galileo_defconfig: *defconfig

70 lines not on this page · raw message

deleted file mode 100644
index 025c97e..0000000
@@ -1,40 +0,0 @@
-You'll need to program the files created by buildroot into the flash.
-The fast way is to tftp transfer the files via one of the network interfaces.
-
-Alternatively you can transfer the files via serial console with an Ymodem
-file transfer from your terminal program by using a "loady" command
-from the u-boot prompt instead of the "tftp ..." commands stated below.
-Beware that serial console file transfers are quite slow!
-
-1. Program the DTB to NOR flash
-
-    => tftp $loadaddr p1010rdb-pa.dtb
-    => erase 0xee000000 +$filesize
-    => cp.b $loadaddr 0xee000000 $filesize
-
-2. Program the kernel to NOR flash
-
-    => tftp $loadaddr uImage
-    => erase 0xee080000 +$filesize
-    => cp.b $loadaddr 0xee080000 $filesize
-
-3. Program the root filesystem to NOR flash
-
-    => tftp $loadaddr rootfs.jffs2
-    => erase 0xee800000 0xeff5ffff
-    => cp.b $loadaddr 0xee800000 $filesize
-
-4. Booting your new system
-
-    => setenv norboot 'setenv bootargs root=/dev/mtdblock2 rootfstype=jffs2 console=$consoledev,$baudrate;bootm 0xee080000 - 0xee000000'
-
-    If you want to set this boot option as default:
-
-    => setenv bootcmd 'run norboot'
-    => saveenv
-
-    ...or for a single boot:
-
-    => run norboot
-
-    You can login with user "root".

deleted file mode 100644
index 3497275..0000000
@@ -1,27 +0,0 @@
-# Architecture
-BR2_powerpc=y
-BR2_powerpc_8548=y
-
-# Filesystem
-# BR2_TARGET_ROOTFS_TAR is not set
-BR2_TARGET_ROOTFS_JFFS2=y
-BR2_TARGET_ROOTFS_JFFS2_CUSTOM=y
-BR2_TARGET_ROOTFS_JFFS2_CUSTOM_PAGESIZE=0x20
-BR2_TARGET_ROOTFS_JFFS2_CUSTOM_EBSIZE=0x20000
-
-# Linux headers same as kernel, a 4.1 series
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
-
-# Kernel
-BR2_LINUX_KERNEL=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.1.4"
-BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/freescale/p1010rdb/linux-4.1.config"
-BR2_LINUX_KERNEL_UIMAGE=y
-BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="p1010rdb-pa"
-
-# Serial port config
-BR2_TARGET_GENERIC_GETTY=y
-BR2_TARGET_GENERIC_GETTY_PORT="ttyS0"