MX51EVK: Remove CPLD related code
PATCH 1/1 MX51EVK: Remove CPLD related code
There is no CPLD on MX51EVK board, so remove CPLD related function.
Signed-off-by Fabio Estevam <[email protected]>
--- board/freescale/mx51evk/mx51evk.c | 67 ------------------------------------- 1 files changed, 0 insertions(+), 67 deletions(-)
board/freescale/mx51evk/mx51evk.c +0 -67
@@ -72,72 +72,6 @@ static void setup_iomux_uart(void)mxc_iomux_set_pad (MX51_PIN_UART1_CTS , pad); } -static void setup_expio (void ) -{ -u32 reg; -struct weim *pweim = (struct weim *)WEIM_BASE_ADDR ; -struct clkctl *pclkctl = (struct clkctl *)CCM_BASE_ADDR ; - -/* CS5 setup */ -mxc_request_iomux (MX51_PIN_EIM_CS5 ,IOMUX_CONFIG_ALT0 ); -writel (0x00410089 , &pweim[5 ].csgcr1); -writel (0x00000002 , &pweim[5 ].csgcr2); - -/* RWSC=50, RADVA=2, RADVN=6, OEA=0, OEN=0, RCSA=0, RCSN=0 */ -writel (0x32260000 , &pweim[5 ].csrcr1); - -/* APR = 0 */ -writel (0x00000000 , &pweim[5 ].csrcr2); - -/* -* WAL=0, WBED=1, WWSC=50, WADVA=2, WADVN=6, WEA=0, WEN=0, -* WCSA=0, WCSN=0 -*/ -writel (0x72080F00 , &pweim[5 ].cswcr1); - - mx51_io_board = (struct io_board_ctrl *)(CS5_BASE_ADDR + -IO_BOARD_OFFSET ); -if ((readw (&mx51_io_board->id1) ==0xAAAA ) && - (readw (&mx51_io_board->id2) ==0x5555 )) { -if (is_soc_rev (CHIP_REV_2_0 ) <0 ) { - reg =readl (&pclkctl->cbcdr); - reg = (reg & (~0x70000 )) |0x30000 ; -writel (reg, &pclkctl->cbcdr); -/* make sure divider effective */ -while (readl (&pclkctl->cdhipr) !=0 ) - ; -writel (0x0 , &pclkctl->ccdr); - } - }else { -/* CS1 */ -writel (0x00410089 , &pweim[1 ].csgcr1); -writel (0x00000002 , &pweim[1 ].csgcr2); -/* RWSC=50, RADVA=2, RADVN=6, OEA=0, OEN=0, RCSA=0, RCSN=0 */ -writel (0x32260000 , &pweim[1 ].csrcr1); -/* APR=0 */ -writel (0x00000000 , &pweim[1 ].csrcr2); -/* -* WAL=0, WBED=1, WWSC=50, WADVA=2, WADVN=6, WEA=0, -* WEN=0, WCSA=0, WCSN=0 -*/ -writel (0x72080F00 , &pweim[1 ].cswcr1); - mx51_io_board = (struct io_board_ctrl *)(CS1_BASE_ADDR + -IO_BOARD_OFFSET ); - } - -/* Reset interrupt status reg */ -writew (0x1F , &(mx51_io_board->int_rest)); -writew (0x00 , &(mx51_io_board->int_rest)); -writew (0xFFFF , &(mx51_io_board->int_mask)); - -/* Reset the XUART and Ethernet controllers */ - reg =readw (&(mx51_io_board->sw_reset)); - reg |=0x9 ; -writew (reg, &(mx51_io_board->sw_reset)); - reg &= ~0x9 ; -writew (reg, &(mx51_io_board->sw_reset)); -} -static void setup_iomux_fec (void ) {/*FEC_MDIO*/
@@ -349,7 +283,6 @@ int board_init(void) gd->bd->bi_boot_params =PHYS_SDRAM_1 +0x100 ;setup_iomux_uart (); -setup_expio ();setup_iomux_fec ();return 0 ; }
Signature · 1 line
1.6.0.4
PATCH 1/1 MX51EVK: Remove CPLD related code
Quoted 4 lines · Fabio Estevam
There is no CPLD on MX51EVK board, so remove CPLD related function.
Signed-off-by Fabio Estevam <[email protected]>---
Agree. Thanks to point out this issue. The code is not needed.
Review
Quoted 2 lines
(quoted diff) +0
-2- mx51_io_board = (struct io_board_ctrl *)(CS5_BASE_ADDR + - IO_BOARD_OFFSET);
You should remove the #define for IO_BOARD_OFFSET from mx51evk.h, too.
Acked-by Stefano Babic <[email protected]>
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de =====================================================================