Skip to contentSkip to conversation

For Help: problems with tx bitrate in ath10k

DISCUSSION wangdc 3 participants 3 messages Apr 8, 2014 – Apr 9, 2014 Qualcomm Atheros ATH10K wireless driver

lore
Share & tools
lore

wangdc

author
#0 lore raw

Hi,all

I used the backports-3.13.2-1 to drive a 11ac card(WLE900VX) on the ubuntu 12.04 LTS(64bit) (3.8.0-35-generic). The card seemed to be working well when i connected it to a broadcom AC APs and the card could also send or receive data normally. But when using command 'iw dev wlan0 station dump' to check the actual Rx and Tx rate, i couldn't get the tx bitrate correctly.

root@ubuntu:~$ iw dev wlan2 station dump
Station 10:48:b1:e8:17:a6 (on wlan2)
    inactive time:    28680 ms
    rx bytes:    903704
    rx packets:    6747
    tx bytes:    20731
    tx packets:    163
    tx retries:    1969
    tx failed:    0
    signal:      -36 dBm
    signal avg:    -36 dBm
    tx bitrate:     MCS 32 40Mhz short GI
    authorized:    yes
    authenticated:    yes
    preamble:    long
    WMM/WME:    yes
    MFP:        no
    TDLS peer:        no

And sometimes the tx bitrate was 3693.3 MBit/s, 65.0 MBit/s, 6.5Mbit/s etc.

The start log as following.

root@ubuntu:~$ dmesg | grep ath
[    0.800424] MODSIGN: Loaded cert 'Magrathea: Glacier signing key: c77318d5b035f7cbfa665f640863f8bc32a3fa33'
[   10.539694] ath10k_pci 0000:04:00.0: BAR 0: assigned [mem 0xf0400000-0xf05fffff 64bit]
[   10.886386] ath10k: MSI-X didn't succeed (1), trying MSI
[   10.886454] ath10k_pci 0000:04:00.0: irq 44 for MSI/MSI-X
[   10.886492] ath10k: MSI interrupt handling
[   10.921722] ath10k: Hardware name qca988x hw2.0 version 0x4100016c
[   12.246510] ath10k: UART prints disabled
[   12.250960] ath10k: firmware 10.1.467.2-1 booted
[   12.260459] ath10k: htt target version 2.1
[   12.261559] ath: EEPROM regdomain: 0x0
[   12.261561] ath: EEPROM indicates default country code should be used
[   12.261562] ath: doing EEPROM country->regdmn map search
[   12.261563] ath: country maps to regdmn code: 0x3a
[   12.261565] ath: Country alpha2 being used: US
[   12.261566] ath: Regpair used: 0x3a
[   18.767377] ath10k: MSI-X didn't succeed (1), trying MSI
[   18.767451] ath10k_pci 0000:04:00.0: irq 44 for MSI/MSI-X
[   18.767496] ath10k: MSI interrupt handling
[   19.700523] ath10k: UART prints disabled
[   19.705037] ath10k: firmware 10.1.467.2-1 booted
[   19.714921] ath10k: htt target version 2.1
...
root@ubuntu:~$ dmesg
[  121.846056] ------------[ cut here ]------------
[  121.846090] WARNING: at /home/backports/net/wireless/util.c:1066 cfg80211_calculate_bitrate+0x18e/0x210 [cfg80211]()
[  121.846093] Hardware name: 23066RC
[  121.846094] Modules linked in: ip_vs(F) nf_conntrack(F) libcrc32c(F) bnep(F) rfcomm(F) parport_pc(F) ppdev(F) arc4(F) coretemp(F) snd_hda_codec_hdmi(F) snd_hda_codec_realtek(F) ath10k_pci(OF) ath10k_core(OF) uvcvideo(F) nfsd(F) snd_hda_intel(F) kvm(F) snd_hda_codec(F) ath(OF) videobuf2_core(F) nfs_acl(F) videodev(F) auth_rpcgss(F) i915(F) nfs(F) videobuf2_vmalloc(F) snd_hwdep(F) btusb(F) snd_pcm(F) mac80211(OF) videobuf2_memops(F) joydev(F) fscache(F) bluetooth(F) ghash_clmulni_intel(F) thinkpad_acpi(F) lockd(F) snd_seq_midi(F) cryptd(F) drm_kms_helper(F) binfmt_misc(F) snd_rawmidi(F) drm(F) snd_seq_midi_event(F) cfg80211(OF) sunrpc(F) snd_seq(F) psmouse(F) snd_timer(F) snd_seq_device(F) mei(F) snd(F) microcode(F) serio_raw(F) mac_hid(F) i2c_algo_bit(F) snd_page_alloc(F) compat(OF) soundcore(F) lpc_ich(F) nvram(F) wmi(F) video(F) lp(F) parport(F) sdhci_pci(F) sdhci(F) e1000e(F)
[  121.846157] Pid: 1050, comm: NetworkManager Tainted: GF O 3.8.0-35-generic #52~precise1-Ubuntu
[  121.846159] Call Trace:
[  121.846171]  [<ffffffff81059b6f>] warn_slowpath_common+0x7f/0xc0
[  121.846177]  [<ffffffff81059bca>] warn_slowpath_null+0x1a/0x20
[  121.846193]  [<ffffffffa019c8de>] cfg80211_calculate_bitrate+0x18e/0x210 [cfg80211]
[  121.846212]  [<ffffffffa01a99a7>] nl80211_put_sta_rate+0x57/0x2a0 [cfg80211]
[  121.846229]  [<ffffffffa01ac0e1>] nl80211_send_station.isra.63+0x4a1/0x870 [cfg80211]
[  121.846246]  [<ffffffffa01ac98c>] nl80211_get_station+0x22c/0x290 [cfg80211]
[  121.846254]  [<ffffffff8160f6dd>] genl_rcv_msg+0x22d/0x2b0
[  121.846260]  [<ffffffff815d830b>] ? __alloc_skb+0x8b/0x2a0
[  121.846264]  [<ffffffff8160f4b0>] ? genl_rcv+0x40/0x40
[  121.846270]  [<ffffffff8160ee89>] netlink_rcv_skb+0xa9/0xd0
[  121.846274]  [<ffffffff8160f495>] genl_rcv+0x25/0x40
[  121.846279]  [<ffffffff8160e7d1>] netlink_unicast+0x1b1/0x230
[  121.846285]  [<ffffffff8160eb4e>] netlink_sendmsg+0x2fe/0x3b0
[  121.846290]  [<ffffffff815cb282>] sock_sendmsg+0xd2/0xf0
[  121.846296]  [<ffffffff815cdb8a>] ? move_addr_to_kernel+0x5a/0xa0
[  121.846300]  [<ffffffff815da406>] ? verify_iovec+0x56/0xd0
[  121.846305]  [<ffffffff815cd09c>] ___sys_sendmsg+0x3ac/0x3c0
[  121.846311]  [<ffffffff811aea86>] ? pollwake+0x66/0x70
[  121.846316]  [<ffffffff81092050>] ? try_to_wake_up+0x200/0x200
[  121.846323]  [<ffffffff816f53e5>] ? _raw_spin_lock_irq+0x15/0x20
[  121.846327]  [<ffffffff81092050>] ? try_to_wake_up+0x200/0x200
[  121.846332]  [<ffffffff815ceba9>] __sys_sendmsg+0x49/0x90
[  121.846337]  [<ffffffff815cec09>] sys_sendmsg+0x19/0x20
[  121.846343]  [<ffffffff816fdf5d>] system_call_fastpath+0x1a/0x1f
[  121.846346] ---[ end trace fc50900f4228222f ]---

About the reason of the warning info above,
when debugging the code, rate->flags was 0x0 and the rate->mcs value was more than 32 in the function of cfg80211_calculate_bitrate, but i didn't know why i got a wrong rate value.

/home/backports/net/wireless/util.c
u32 cfg80211_calculate_bitrate(struct rate_info *rate)

{
    int modulation, streams, bitrate;

    if (!(rate->flags & RATE_INFO_FLAGS_MCS) &&
        !(rate->flags & RATE_INFO_FLAGS_VHT_MCS))
        return rate->legacy;
    if (rate->flags & RATE_INFO_FLAGS_60G)
        return cfg80211_calculate_bitrate_60g(rate);
    if (rate->flags & RATE_INFO_FLAGS_VHT_MCS)
        return cfg80211_calculate_bitrate_vht(rate);

    /* the formula below does only work for MCS values smaller than 32 */
    if (WARN_ON_ONCE(rate->mcs >= 32))
        return 0;

I tried other version of the firmware and backports, the test results were as following:
a)The problem repeated when i tried firmware-2.bin_999.999.0.636.
b)The tx bitrate was fixed to 6MBit/s and there was no warning info in the boot log when i adopted the latest development releases(backports-20140221).

Is there anybody meets the same problem? If so, please give me some suggestion on getting Tx rate properly.

Thanks.
Rex

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#1 lore raw

Need firmware change to get proper Tx rate as pointed out by Kalle Valo. So no support for the time being.

http://lists.infradead.org/pipermail/ath10k/2014-March/001587.html

----
Chun-Yeow

Quoted 141 lines · wangdc

Hi,all

I used the backports-3.13.2-1 to drive a 11ac card(WLE900VX) on the ubuntu 12.04 LTS(64bit) (3.8.0-35-generic).
The card seemed to be working well when i connected it to a broadcom AC APs and the card could also send or receive data normally.
But when using command 'iw dev wlan0 station dump' to check the actual Rx and Tx rate, i couldn't get the tx bitrate correctly.

root@ubuntu:~$ iw dev wlan2 station dump
Station 10:48:b1:e8:17:a6 (on wlan2)
    inactive time:    28680 ms
    rx bytes:    903704
    rx packets:    6747
    tx bytes:    20731
    tx packets:    163
    tx retries:    1969
    tx failed:    0
    signal:      -36 dBm
    signal avg:    -36 dBm
    tx bitrate:     MCS 32 40Mhz short GI
    authorized:    yes
    authenticated:    yes
    preamble:    long
    WMM/WME:    yes
    MFP:        no
    TDLS peer:        no

And sometimes the tx bitrate was 3693.3 MBit/s, 65.0 MBit/s, 6.5Mbit/s etc.

The start log as following.

root@ubuntu:~$ dmesg | grep ath
[    0.800424] MODSIGN: Loaded cert 'Magrathea: Glacier signing key:
c77318d5b035f7cbfa665f640863f8bc32a3fa33'
[   10.539694] ath10k_pci 0000:04:00.0: BAR 0: assigned [mem
0xf0400000-0xf05fffff 64bit]
[   10.886386] ath10k: MSI-X didn't succeed (1), trying MSI
[   10.886454] ath10k_pci 0000:04:00.0: irq 44 for MSI/MSI-X
[   10.886492] ath10k: MSI interrupt handling
[   10.921722] ath10k: Hardware name qca988x hw2.0 version 0x4100016c
[   12.246510] ath10k: UART prints disabled
[   12.250960] ath10k: firmware 10.1.467.2-1 booted
[   12.260459] ath10k: htt target version 2.1
[   12.261559] ath: EEPROM regdomain: 0x0
[   12.261561] ath: EEPROM indicates default country code should be used
[   12.261562] ath: doing EEPROM country->regdmn map search
[   12.261563] ath: country maps to regdmn code: 0x3a
[   12.261565] ath: Country alpha2 being used: US
[   12.261566] ath: Regpair used: 0x3a
[   18.767377] ath10k: MSI-X didn't succeed (1), trying MSI
[   18.767451] ath10k_pci 0000:04:00.0: irq 44 for MSI/MSI-X
[   18.767496] ath10k: MSI interrupt handling
[   19.700523] ath10k: UART prints disabled
[   19.705037] ath10k: firmware 10.1.467.2-1 booted
[   19.714921] ath10k: htt target version 2.1
...
root@ubuntu:~$ dmesg
[  121.846056] ------------[ cut here ]------------
[  121.846090] WARNING: at /home/backports/net/wireless/util.c:1066
cfg80211_calculate_bitrate+0x18e/0x210 [cfg80211]()
[  121.846093] Hardware name: 23066RC
[  121.846094] Modules linked in: ip_vs(F) nf_conntrack(F) libcrc32c(F)
bnep(F) rfcomm(F) parport_pc(F) ppdev(F) arc4(F) coretemp(F)
snd_hda_codec_hdmi(F) snd_hda_codec_realtek(F) ath10k_pci(OF)
ath10k_core(OF) uvcvideo(F) nfsd(F) snd_hda_intel(F) kvm(F) snd_hda_codec(F)
ath(OF) videobuf2_core(F) nfs_acl(F) videodev(F) auth_rpcgss(F) i915(F)
nfs(F) videobuf2_vmalloc(F) snd_hwdep(F) btusb(F) snd_pcm(F) mac80211(OF)
videobuf2_memops(F) joydev(F) fscache(F) bluetooth(F) ghash_clmulni_intel(F)
thinkpad_acpi(F) lockd(F) snd_seq_midi(F) cryptd(F) drm_kms_helper(F)
binfmt_misc(F) snd_rawmidi(F) drm(F) snd_seq_midi_event(F) cfg80211(OF)
sunrpc(F) snd_seq(F) psmouse(F) snd_timer(F) snd_seq_device(F) mei(F) snd(F)
microcode(F) serio_raw(F) mac_hid(F) i2c_algo_bit(F) snd_page_alloc(F)
compat(OF) soundcore(F) lpc_ich(F) nvram(F) wmi(F) video(F) lp(F) parport(F)
sdhci_pci(F) sdhci(F) e1000e(F)
[  121.846157] Pid: 1050, comm: NetworkManager Tainted: GF O
3.8.0-35-generic #52~precise1-Ubuntu
[  121.846159] Call Trace:
[  121.846171]  [<ffffffff81059b6f>] warn_slowpath_common+0x7f/0xc0
[  121.846177]  [<ffffffff81059bca>] warn_slowpath_null+0x1a/0x20
[  121.846193]  [<ffffffffa019c8de>] cfg80211_calculate_bitrate+0x18e/0x210
[cfg80211]
[  121.846212]  [<ffffffffa01a99a7>] nl80211_put_sta_rate+0x57/0x2a0
[cfg80211]
[  121.846229]  [<ffffffffa01ac0e1>]
nl80211_send_station.isra.63+0x4a1/0x870 [cfg80211]
[  121.846246]  [<ffffffffa01ac98c>] nl80211_get_station+0x22c/0x290
[cfg80211]
[  121.846254]  [<ffffffff8160f6dd>] genl_rcv_msg+0x22d/0x2b0
[  121.846260]  [<ffffffff815d830b>] ? __alloc_skb+0x8b/0x2a0
[  121.846264]  [<ffffffff8160f4b0>] ? genl_rcv+0x40/0x40
[  121.846270]  [<ffffffff8160ee89>] netlink_rcv_skb+0xa9/0xd0
[  121.846274]  [<ffffffff8160f495>] genl_rcv+0x25/0x40
[  121.846279]  [<ffffffff8160e7d1>] netlink_unicast+0x1b1/0x230
[  121.846285]  [<ffffffff8160eb4e>] netlink_sendmsg+0x2fe/0x3b0
[  121.846290]  [<ffffffff815cb282>] sock_sendmsg+0xd2/0xf0
[  121.846296]  [<ffffffff815cdb8a>] ? move_addr_to_kernel+0x5a/0xa0
[  121.846300]  [<ffffffff815da406>] ? verify_iovec+0x56/0xd0
[  121.846305]  [<ffffffff815cd09c>] ___sys_sendmsg+0x3ac/0x3c0
[  121.846311]  [<ffffffff811aea86>] ? pollwake+0x66/0x70
[  121.846316]  [<ffffffff81092050>] ? try_to_wake_up+0x200/0x200
[  121.846323]  [<ffffffff816f53e5>] ? _raw_spin_lock_irq+0x15/0x20
[  121.846327]  [<ffffffff81092050>] ? try_to_wake_up+0x200/0x200
[  121.846332]  [<ffffffff815ceba9>] __sys_sendmsg+0x49/0x90
[  121.846337]  [<ffffffff815cec09>] sys_sendmsg+0x19/0x20
[  121.846343]  [<ffffffff816fdf5d>] system_call_fastpath+0x1a/0x1f
[  121.846346] ---[ end trace fc50900f4228222f ]---

About the reason of the warning info above,
when debugging the code, rate->flags was 0x0 and the rate->mcs value was more than 32 in the function of cfg80211_calculate_bitrate, but i didn't know why i got a wrong rate value.

/home/backports/net/wireless/util.c
u32 cfg80211_calculate_bitrate(struct rate_info *rate)

{
    int modulation, streams, bitrate;

    if (!(rate->flags & RATE_INFO_FLAGS_MCS) &&
        !(rate->flags & RATE_INFO_FLAGS_VHT_MCS))
        return rate->legacy;
    if (rate->flags & RATE_INFO_FLAGS_60G)
        return cfg80211_calculate_bitrate_60g(rate);
    if (rate->flags & RATE_INFO_FLAGS_VHT_MCS)
        return cfg80211_calculate_bitrate_vht(rate);

    /* the formula below does only work for MCS values smaller than 32 */
    if (WARN_ON_ONCE(rate->mcs >= 32))
        return 0;

I tried other version of the firmware and backports, the test results were as following:
a)The problem repeated when i tried firmware-2.bin_999.999.0.636. b)The tx bitrate was fixed to 6MBit/s and there was no warning info in the boot log when i adopted the latest development releases(backports-20140221).

Is there anybody meets the same problem? If so, please give me some suggestion on getting Tx rate properly.

Quoted 8 lines

Thanks.
Rex

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#2 lore raw
Quoted 4 lines · Yeoh Chun-Yeow

Need firmware change to get proper Tx rate as pointed out by Kalle Valo. So no support for the time being.

http://lists.infradead.org/pipermail/ath10k/2014-March/001587.html

That's right. I added this question also to the FAQ:

http://wireless.kernel.org/en/users/Drivers/ath10k/faq#Why_the_TX_rate_reported_to_user_space_is_wrong.3F

Is there any way to report to user space that TX rate reports are not supported? If not, it would be great if someone would have time to add that to cfg80211/mac80211. This issue is confusing a lot of people.

Signature · 6 lines
Kalle Valo

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k