usb: ehci-mx6: Add powerup_fixup implementation
Subsystems (2)
PATCH 1/7 usb: ehci-mx6: Add powerup_fixup implementation
From: Ye Li <[email protected]>
When doing port reset, the PR bit of PORTSC1 will be automatically cleared by our IP, but standard EHCI needs explicit clear by software. The EHCI-HCD driver follow the EHCI specification, so after 50ms wait, it clear the PR bit by writting to the PORTSC1 register with value loaded before setting PR.
This sequence is ok for our IP when the delay time is exact. But when the timer is slower, some bits like PE, PSPD have been set by controller automatically after the PR is automatically cleared. So the writing to the PORTSC1 will overwrite these bits set by controller. And eventually the driver gets wrong status.
We implement the powerup_fixup operation which delays 50ms and will check the PR until it is cleared by controller. And will update the reg value which is written to PORTSC register by EHCI-HCD driver. This is much safer than depending on the delay time to be accurate and aligining with controller's behaiver.
--- drivers/usb/host/ehci-mx6.c | 28 +++++++++++++++++++++++++++- 1 file changed, 27 insertions(+), 1 deletion(-)
drivers/usb/host/ehci-mx6.c +27 -1
@@ -267,6 +267,25 @@ int usb_phy_mode(int port) }#endif +static void ehci_mx6_powerup_fixup (struct ehci_ctrl *ctrl,uint32_t *status_reg, +uint32_t *reg) +{ +u32 result; +int usec =2000 ; + +mdelay (50 ); + +do { + result =ehci_readl (status_reg); +udelay (5 ); +if (!(result &EHCI_PS_PR )) +break ; + usec--; + }while (usec >0 ); + + *reg =ehci_readl (status_reg); +} +static void usb_oc_config (int index) {#if defined(CONFIG_MX6 )
@@ -366,6 +385,10 @@ int ehci_mx6_common_init(struct usb_ehci *ehci, int index) }#if !CONFIG_IS_ENABLED (DM_USB ) +static const struct ehci_ops mx6_ehci_ops = { + .powerup_fixup = ehci_mx6_powerup_fixup, +}; +int ehci_hcd_init (int index,enum usb_init_type init,struct ehci_hccr **hccr,struct ehci_hcor **hcor) {
@@ -394,6 +417,8 @@ int ehci_hcd_init(int index, enum usb_init_type init,if (ret)return ret; +ehci_set_controller_priv (index,NULL , &mx6_ehci_ops); + type =board_usb_phy_mode (index);if (hccr && hcor) {
@@ -467,7 +492,8 @@ static int mx6_init_after_reset(struct ehci_ctrl *dev) }static const struct ehci_ops mx6_ehci_ops = { - .init_after_reset = mx6_init_after_reset + .powerup_fixup = ehci_mx6_powerup_fixup, + .init_after_reset = mx6_init_after_reset };static int ehci_usb_phy_mode (struct udevice *dev)
Signature · 1 line
2.16.4
PATCH 2/7 usb: ehci-mx6: Add i.MX8 OTG controller support
From: Ye Li <[email protected]>
The i.MX8 has two USB controllers: USBOH and USB3. The USBOH reuses previous i.MX6/7. It has same PHY IP as i.MX7ULP but NC registers are same as i.MX7D. So add its support in ehci-mx6 driver.
Also the driver is updated to remove build warning for 64 bits CPU.
--- drivers/usb/host/Kconfig | 4 +- drivers/usb/host/ehci-mx6.c | 97 ++++++++++++++++++++++++++++++++++++++------- 2 files changed, 85 insertions(+), 16 deletions(-)
drivers/usb/host/Kconfig +2 -2
@@ -139,8 +139,8 @@ config USB_EHCI_MX5 Enables support for the on-chip EHCI controller on i.MX5 SoCs. config USB_EHCI_MX6 - bool "Support for i.MX6/i.MX7ULP on-chip EHCI USB controller" - depends on ARCH_MX6 || ARCH_MX7ULP + bool "Support for i.MX6/i.MX7ULP/i.MX8 on-chip EHCI USB controller" + depends on ARCH_MX6 || ARCH_MX7ULP || ARCH_IMX8 default y ---help--- Enables support for the on-chip EHCI controller on i.MX6 SoCs.
drivers/usb/host/ehci-mx6.c +83 -14
169 lines not on this page · raw message
Signature · 1 line
2.16.4
PATCH 2/7 usb: ehci-mx6: Add i.MX8 OTG controller support
On 6/29/20 4:13 AM, Peng Fan wrote:
Hi,
Quoted 5 lines
The i.MX8 has two USB controllers: USBOH and USB3. The USBOH reuses previous i.MX6/7. It has same PHY IP as i.MX7ULP but NC registers are same as i.MX7D. So add its support in ehci-mx6 driver.
Also the driver is updated to remove build warning for 64 bits CPU.
Please split the fixes into separate patch.
drivers/usb/host/ehci-mx6.c DECLARE_GLOBAL_DATA_PTR; · line 71
Quoted 13 lines
drivers/usb/host/ehci-mx6.c +7
-0@@ -62,12 +62,20 @@ DECLARE_GLOBAL_DATA_PTR;#define UCTRL_OVER_CUR_POL (1 << 8)/* OTG Polarity of Overcurrent */ #define UCTRL_OVER_CUR_DIS (1 << 7)/* Disable OTG Overcurrent Detection */ +#define PLL_USB_EN_USB_CLKS_MASK (0x01 << 6) +#define PLL_USB_PWR_MASK (0x01 << 12) +#define PLL_USB_ENABLE_MASK (0x01 << 13) +#define PLL_USB_BYPASS_MASK (0x01 << 16) +#define PLL_USB_REG_ENABLE_MASK (0x01 << 21) +#define PLL_USB_DIV_SEL_MASK (0x07 << 22) +#define PLL_USB_LOCK_MASK (0x01 << 31)
Use BIT() macro
Quoted 12 lines
drivers/usb/host/ehci-mx6.c +2
-2/* USBCMD */ #define UCMD_RUN_STOP (1 << 0)/* controller run/stop */ #define UCMD_RESET (1 << 1)/* controller reset */ -#if defined(CONFIG_MX6 ) || defined(CONFIG_MX7ULP ) -static const unsigned phy_bases[] = { +#if defined(CONFIG_MX6 ) || defined(CONFIG_MX7ULP ) || defined(CONFIG_IMX8 ) +static const ulong phy_bases[] = {USB_PHY0_BASE_ADDR , #if defined(USB_PHY1_BASE_ADDR) USB_PHY1_BASE_ADDR,
drivers/usb/host/ehci-mx6.c static void usb_power_config(int index) · line 112
Quoted 4 lines
drivers/usb/host/ehci-mx6.c +1
-0@@ -101,6 +109,53 @@ static void usb_power_config(int index)scg_enable_usb_pll (true); +#elif defined(CONFIG_IMX8 )
This function should be split into multiple, it's too long, make it a per-SoC function.
Quoted 20 lines
drivers/usb/host/ehci-mx6.c +20
-0+struct usbphy_regs __iomem *usbphy = + (struct usbphy_regs __iomem *)USB_PHY0_BASE_ADDR ; +int timeout =1000000 ; + +if (index >0 ) +return ; + +writel (ANADIG_USB2_CHRG_DETECT_EN_B | +ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B , + &usbphy->usb1_chrg_detect); + +if (!(readl (&usbphy->usb1_pll_480_ctrl) &PLL_USB_LOCK_MASK )) { + +/* Enable the regulator first */ +writel (PLL_USB_REG_ENABLE_MASK , + &usbphy->usb1_pll_480_ctrl_set); + +/* Wait at least 25us */ +udelay (25 ); +
drivers/usb/host/ehci-mx6.c static void usb_power_config(int index) · line 142
Quoted 10 lines
drivers/usb/host/ehci-mx6.c +10
-0+/* Enable the power */ +writel (PLL_USB_PWR_MASK , &usbphy->usb1_pll_480_ctrl_set); + +/* Wait lock */ +while (timeout--) { +if (readl (&usbphy->usb1_pll_480_ctrl) & +PLL_USB_LOCK_MASK ) +break ; +udelay (10 ); + }
Use wait_for_bit*() here.
[...]
drivers/usb/host/ehci-mx6.c struct usbnc_regs { · line 312
Quoted 4 lines
drivers/usb/host/ehci-mx6.c +1
-1static void usb_power_config (int index) { - struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR + + struct usbnc_regs *usbnc = (struct usbnc_regs *)(ulong)(USB_BASE_ADDR +
Is the extra type cast really needed ? If so, then it should be uintptr_t so it would work with 64bit addresses.
[...]
PATCH 2/7 usb: ehci-mx6: Add i.MX8 OTG controller support
Quoted 6 lines
Subject: Re: [PATCH 2/7] usb: ehci-mx6: Add i.MX8 OTG controller support
On 6/29/20 4:13 AM, Peng Fan wrote:
Hi,
Quoted 7 lines
Quoted 5 lines
The i.MX8 has two USB controllers: USBOH and USB3. The USBOH reuses previous i.MX6/7. It has same PHY IP as i.MX7ULP but NC registers are same as i.MX7D. So add its support in ehci-mx6 driver.
Also the driver is updated to remove build warning for 64 bits CPU.
Please split the fixes into separate patch.
Sorry for not be clear, but the driver was only built for ARM32 i.MX. It is after we start supporting i.MX8, there are some warnings, which was introduced by adding i.MX8 support. It should stay in same patch.
Quoted 9 lines
drivers/usb/host/ehci-mx6.c DECLARE_GLOBAL_DATA_PTR; · line 62
Quoted 5 lines
drivers/usb/host/ehci-mx6.c +0
-0@@ -62,12 +62,20 @@ DECLARE_GLOBAL_DATA_PTR;#define UCTRL_OVER_CUR_POL (1 << 8)/* OTG Polarity of Overcurrent */
drivers/usb/host/ehci-mx6.c DECLARE_GLOBAL_DATA_PTR; · line 63
Quoted 1 line
drivers/usb/host/ehci-mx6.c +0
-0#define UCTRL_OVER_CUR_DIS (1 << 7)/* Disable OTG Overcurrent Detection */
Quoted 1 line
Quoted 9 lines
drivers/usb/host/ehci-mx6.c DECLARE_GLOBAL_DATA_PTR; · line 71
Quoted 7 lines
drivers/usb/host/ehci-mx6.c +7
-0+#define PLL_USB_EN_USB_CLKS_MASK (0x01 << 6) +#define PLL_USB_PWR_MASK (0x01 << 12) +#define PLL_USB_ENABLE_MASK (0x01 << 13) +#define PLL_USB_BYPASS_MASK (0x01 << 16) +#define PLL_USB_REG_ENABLE_MASK (0x01 << 21) +#define PLL_USB_DIV_SEL_MASK (0x07 << 22) +#define PLL_USB_LOCK_MASK (0x01 << 31)Use
BIT()macro
Yes.
Quoted 14 lines
Quoted 14 lines
/* USBCMD */
#defineUCMD_RUN_STOP(1 << 0) /* controller run/stop */
#defineUCMD_RESET(1 << 1) /* controller reset */-#if
defined(CONFIG_MX6)||defined(CONFIG_MX7ULP)-static const unsigned phy_bases[] = {drivers/usb/host/ehci-mx6.c +2
-0+#if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP) || +defined(CONFIG_IMX8) static const ulong phy_bases[] = { USB_PHY0_BASE_ADDR,#if defined(USB_PHY1_BASE_ADDR ) USB_PHY1_BASE_ADDR,@@ -101,6 +109,53 @@ static void usb_power_config(int index)
Quoted 6 lines
drivers/usb/host/ehci-mx6.c static void usb_power_config(int index) · line 112
Quoted 3 lines
drivers/usb/host/ehci-mx6.c +1
-0scg_enable_usb_pll (true); +#elif defined(CONFIG_IMX8 )This function should be split into multiple, it's too long, make it a per-SoC function.
Ok.
Quoted 25 lines
Quoted 25 lines
drivers/usb/host/ehci-mx6.c +24
-0+struct usbphy_regs __iomem *usbphy = + (struct usbphy_regs __iomem *)USB_PHY0_BASE_ADDR ; +int timeout =1000000 ; + +if (index >0 ) +return ; + +writel (ANADIG_USB2_CHRG_DETECT_EN_B | +ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B , + &usbphy->usb1_chrg_detect); + +if (!(readl (&usbphy->usb1_pll_480_ctrl) &PLL_USB_LOCK_MASK )) { + +/* Enable the regulator first */ +writel (PLL_USB_REG_ENABLE_MASK , + &usbphy->usb1_pll_480_ctrl_set); + +/* Wait at least 25us */ +udelay (25 ); + +/* Enable the power */ +writel (PLL_USB_PWR_MASK , &usbphy->usb1_pll_480_ctrl_set); + +/* Wait lock */
Quoted 8 lines
drivers/usb/host/ehci-mx6.c static void usb_power_config(int index) · line 142
Quoted 6 lines
drivers/usb/host/ehci-mx6.c +6
-0+while (timeout--) { +if (readl (&usbphy->usb1_pll_480_ctrl) & +PLL_USB_LOCK_MASK ) +break ; +udelay (10 ); + }Use wait_for_bit*() here.
ok.
Quoted 10 lines
[...]
drivers/usb/host/ehci-mx6.c
Quoted 4 lines
static void
usb_power_config(int index){drivers/usb/host/ehci-mx6.c +2
-1- struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR + +struct usbnc_regs *usbnc = (struct usbnc_regs +*)(ulong)(USB_BASE_ADDR +Is the extra type cast really needed ? If so, then it should be
uintptr_tso it would work with 64bit addresses.
Will use uintptr_t. there is warning if not.
"warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]"
Thanks,
Peng.
Quoted 2 lines
[...]
PATCH 2/7 usb: ehci-mx6: Add i.MX8 OTG controller support
On 6/29/20 10:24 AM, Peng Fan wrote:
[...]
Quoted 11 lines
Quoted 7 lines
Quoted 5 lines
The i.MX8 has two USB controllers: USBOH and USB3. The USBOH reuses previous i.MX6/7. It has same PHY IP as i.MX7ULP but NC registers are same as i.MX7D. So add its support in ehci-mx6 driver.
Also the driver is updated to remove build warning for 64 bits CPU.
Please split the fixes into separate patch.
Sorry for not be clear, but the driver was only built for ARM32 i.MX. It is after we start supporting i.MX8, there are some warnings, which was introduced by adding i.MX8 support. It should stay in same patch.
I understand that, but the 64bit fixes can be pulled into separate patch to make it easier to review just the OTG support without having the fixes mixed in the same patch.
[...]
Quoted 11 lines
Quoted 7 lines
Review
Quoted 4 lines
static void
usb_power_config(int index){(quoted diff) +2
-1- struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR + + struct usbnc_regs *usbnc = (struct usbnc_regs +*)(ulong)(USB_BASE_ADDR +Is the extra type cast really needed ? If so, then it should be
uintptr_tso it would work with 64bit addresses.Will use
uintptr_t. there is warning if not."warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]"
[...]
PATCH 3/7 usb: ehci-mx6: Turn on the power domain of USB PHY
In reply to Peng FanFrom: Ye Li <[email protected]>
Since there is no uclass for USB PHY. The device won't be setup for the USB PHY node in DTB. And its associated power domain device won't be turned on neither by DM framework.
This patch modifies the ehci-mx6 driver to enable the power domain device before access the USB PHY. This is only for DM driver. For non-DM part, users still need to power on the USB PHY in boards/SoC codes.
--- drivers/usb/host/ehci-mx6.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)
drivers/usb/host/ehci-mx6.c +17 -0
@@ -2,6 +2,8 @@/* * Copyright (c) 2009 Daniel Mack <[email protected]> * Copyright (C) 2010 Freescale Semiconductor, Inc. +* Copyright 2017 NXP +* */ #include <common.h>
@@ -23,6 +25,9 @@#include <linux/usb/otg.h> #include "ehci.h" +#if CONFIG_IS_ENABLED (POWER_DOMAIN ) +#include <power-domain.h> +#endif DECLARE_GLOBAL_DATA_PTR ;
@@ -590,6 +595,18 @@ static int ehci_usb_phy_mode(struct udevice *dev)if ((fdt_addr_t )addr ==FDT_ADDR_T_NONE )return -EINVAL ; +/* Need to power on the PHY before access it */ +#if CONFIG_IS_ENABLED (POWER_DOMAIN ) +struct udevice phy_dev; +struct power_domain pd; + + phy_dev.node =offset_to_ofnode (phy_off); +if (!power_domain_get (&phy_dev, &pd)) { +if (power_domain_on (&pd)) +return -EINVAL ; + } +#endif + phy_ctrl = (void __iomem *)(addr +USBPHY_CTRL ); val =readl (phy_ctrl);
Signature · 1 line
2.16.4
PATCH 3/7 usb: ehci-mx6: Turn on the power domain of USB PHY
On 6/29/20 4:13 AM, Peng Fan wrote:
[...]
drivers/usb/host/ehci-mx6.c line 30
Quoted 7 lines
drivers/usb/host/ehci-mx6.c +3
-0@@ -23,6 +25,9 @@#include <linux/usb/otg.h> #include "ehci.h" +#if CONFIG_IS_ENABLED (POWER_DOMAIN ) +#include <power-domain.h> +#endif
The ifdef here should not be needed.
Quoted 5 lines
drivers/usb/host/ehci-mx6.c +0
-0DECLARE_GLOBAL_DATA_PTR ;@@ -590,6 +595,18 @@ static int ehci_usb_phy_mode(struct udevice *dev)if ((fdt_addr_t )addr ==FDT_ADDR_T_NONE )return -EINVAL ;
drivers/usb/host/ehci-mx6.c static int ehci_usb_phy_mode(struct udevice *dev) · line 606
Quoted 10 lines
drivers/usb/host/ehci-mx6.c +9
-0+/* Need to power on the PHY before access it */ +#if CONFIG_IS_ENABLED (POWER_DOMAIN ) +struct udevice phy_dev; +struct power_domain pd; + + phy_dev.node =offset_to_ofnode (phy_off); +if (!power_domain_get (&phy_dev, &pd)) { +if (power_domain_on (&pd)) +return -EINVAL ;
Please return the return value of power_domain_on() in case of failure.
[...]
PATCH 4/7 usb: ehci-mx6: Update driver to support i.MX8MM
In reply to Peng FanFrom: Ye Li <[email protected]>
Since the i.MX8MM reuses the otg controllers on i.MX7D. We can use CONFIG_USB_EHCI_MX7 for them.
Due the TCPC and load switch are used on Typec circuit. Add the board_usb_init and board_usb_cleanup to ehci-mx6 DM driver. So we can implement the TCPC settings in these board functions.
--- drivers/usb/host/Kconfig | 2 +- drivers/usb/host/ehci-mx6.c | 31 ++++++++++++++++++++++++++----- 2 files changed, 27 insertions(+), 6 deletions(-)
drivers/usb/host/Kconfig +1 -1
@@ -147,7 +147,7 @@ config USB_EHCI_MX6 config USB_EHCI_MX7 bool "Support for i.MX7 on-chip EHCI USB controller" - depends on ARCH_MX7 + depends on ARCH_MX7 || IMX8MM default y ---help--- Enables support for the on-chip EHCI controller on i.MX7 SoCs.
drivers/usb/host/ehci-mx6.c +26 -5
@@ -297,7 +297,7 @@ struct usbnc_regs { };#endif -#elif defined(CONFIG_MX7) +#elif defined(CONFIG_USB_EHCI_MX7)struct usbnc_regs {u32 ctrl1;u32 ctrl2;
@@ -366,7 +366,7 @@ static void usb_oc_config(int index)struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +USB_OTHERREGS_OFFSET );void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]); -#elif defined(CONFIG_MX7 ) || defined(CONFIG_MX7ULP ) || defined(CONFIG_IMX8 ) +#elif defined(CONFIG_USB_EHCI_MX7 ) || defined(CONFIG_MX7ULP ) || defined(CONFIG_IMX8 )struct usbnc_regs *usbnc = (struct usbnc_regs *)(ulong)(USB_BASE_ADDR + (0x10000 * index) +USBNC_OFFSET );void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl1);
@@ -469,7 +469,7 @@ int ehci_hcd_init(int index, enum usb_init_type init,enum usb_init_type type;#if defined(CONFIG_MX6 )u32 controller_spacing =0x200 ; -#elif defined(CONFIG_MX7 ) || defined(CONFIG_MX7ULP ) || defined(CONFIG_IMX8 ) +#elif defined(CONFIG_USB_EHCI_MX7 ) || defined(CONFIG_MX7ULP ) || defined(CONFIG_IMX8 )u32 controller_spacing =0x10000 ;#endif struct usb_ehci *ehci = (struct usb_ehci *)(ulong)(USB_BASE_ADDR +
@@ -537,6 +537,12 @@ static int mx6_init_after_reset(struct ehci_ctrl *dev)struct usb_ehci *ehci = priv->ehci;int ret; + ret =board_usb_init (priv->portnr, priv->init_type); +if (ret) { +printf ("Failed to initialize board for USB\n" ); +return ret; + } + ret =ehci_mx6_common_init (priv->ehci, priv->portnr);if (ret)return ret;
@@ -614,7 +620,7 @@ static int ehci_usb_phy_mode(struct udevice *dev) plat->init_type =USB_INIT_DEVICE ; else plat->init_type = USB_INIT_HOST; - }else if (is_mx7 ()) { + }else if (is_mx7 () ||is_imx8mm ()) { phy_status = (void __iomem *)(addr +USBNC_PHY_STATUS_OFFSET ); val =readl (phy_status);
@@ -711,6 +717,12 @@ static int ehci_usb_probe(struct udevice *dev) priv->portnr = dev->seq; priv->init_type = type; + ret =board_usb_init (priv->portnr, priv->init_type); +if (ret) { +printf ("Failed to initialize board for USB\n" ); +return ret; + } +#if CONFIG_IS_ENABLED (DM_REGULATOR ) ret =device_get_supply_regulator (dev,"vbus-supply" , &priv->vbus_supply);
@@ -748,6 +760,15 @@ static int ehci_usb_probe(struct udevice *dev)return ehci_register (dev, hccr, hcor, &mx6_ehci_ops,0 , priv->init_type); } +int ehci_usb_remove (struct udevice *dev) +{ +struct ehci_mx6_priv_data *priv =dev_get_priv (dev); + +ehci_deregister (dev); + +return board_usb_cleanup (dev->seq, priv->init_type); +} +static const struct udevice_id mx6_usb_ids[] = { { .compatible ="fsl,imx27-usb" }, { }
@@ -760,7 +781,7 @@ U_BOOT_DRIVER(usb_mx6) = { .ofdata_to_platdata = ehci_usb_ofdata_to_platdata, .bind = ehci_usb_bind, .probe = ehci_usb_probe, - .remove = ehci_deregister, + .remove = ehci_usb_remove, .ops = &ehci_usb_ops, .platdata_auto_alloc_size = sizeof(struct usb_platdata), .priv_auto_alloc_size = sizeof(struct ehci_mx6_priv_data),
Signature · 1 line
2.16.4
PATCH 4/7 usb: ehci-mx6: Update driver to support i.MX8MM
On 6/29/20 4:13 AM, Peng Fan wrote:
[...]
drivers/usb/host/ehci-mx6.c static void usb_oc_config(int index) · line 369
Quoted 6 lines
drivers/usb/host/ehci-mx6.c +1
-1@@ -366,7 +366,7 @@ static void usb_oc_config(int index)struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +USB_OTHERREGS_OFFSET );void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]); -#elif defined(CONFIG_MX7 ) || defined(CONFIG_MX7ULP ) || defined(CONFIG_IMX8 ) +#elif defined(CONFIG_USB_EHCI_MX7 ) || defined(CONFIG_MX7ULP ) || defined(CONFIG_IMX8 )
Can someone please clean up this growing ifdeffery ? This doesn't work with the driver model. It's fine to do that in a subsequent patch, but it really should be done soon.
Quoted 13 lines
drivers/usb/host/ehci-mx6.c +1
-1struct usbnc_regs *usbnc = (struct usbnc_regs *)(ulong)(USB_BASE_ADDR + (0x10000 * index) +USBNC_OFFSET );void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl1);@@ -469,7 +469,7 @@ int ehci_hcd_init(int index, enum usb_init_type init,enum usb_init_type type;#if defined(CONFIG_MX6 )u32 controller_spacing =0x200 ; -#elif defined(CONFIG_MX7 ) || defined(CONFIG_MX7ULP ) || defined(CONFIG_IMX8 ) +#elif defined(CONFIG_USB_EHCI_MX7 ) || defined(CONFIG_MX7ULP ) || defined(CONFIG_IMX8 )u32 controller_spacing =0x10000 ;#endif struct usb_ehci *ehci = (struct usb_ehci *)(ulong)(USB_BASE_ADDR +
drivers/usb/host/ehci-mx6.c static int mx6_init_after_reset(struct ehci_ctrl *dev) · line 544
Quoted 8 lines
drivers/usb/host/ehci-mx6.c +5
-0@@ -537,6 +537,12 @@ static int mx6_init_after_reset(struct ehci_ctrl *dev)struct usb_ehci *ehci = priv->ehci;int ret; + ret =board_usb_init (priv->portnr, priv->init_type); +if (ret) { +printf ("Failed to initialize board for USB\n" ); +return ret; + }
Are these hooks needed ?
PATCH 5/7 usb: ehci-mx6: fix controller index for imx8m and imx8
In reply to Peng FanFrom: Ye Li <[email protected]>
The bind codes calculate the address offset for controller index, but it is wrong for imx8m and imx8. It causes secondary controller fails to work. So fix this problem, and also change all seq to req_seq.
There is another issue here for imx8, the codes use runtime CPU type check. One iMX8, this check depends on IPC communication with SCFW, and need MU driver been probed. But the usbotg is configured with "u-boot,dm_spl" property for SDP download in SPL, so it will bind in early DM in u-boot while the MU is not bound at same time, so the CPU type check will hang. Fix it to use static check.
--- drivers/usb/host/ehci-mx6.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/usb/host/ehci-mx6.c +7 -3
@@ -687,7 +687,11 @@ static int ehci_usb_bind(struct udevice *dev)* With these changes in place, the ad-hoc indexing goes away and * the driver is fully converted to DT probing. */ -u32 controller_spacing =is_mx7 () ?0x10000 :0x200 ; +u32 controller_spacing; +if (IS_ENABLED (CONFIG_MX6 )) + controller_spacing =0x200 ; +else + controller_spacing =0x10000 ;fdt_addr_t addr =devfdt_get_addr_index (dev,0 ); dev->req_seq = (addr -USB_BASE_ADDR ) / controller_spacing;
@@ -714,7 +718,7 @@ static int ehci_usb_probe(struct udevice *dev) } priv->ehci = ehci; - priv->portnr = dev->seq; + priv->portnr = dev->req_seq; priv->init_type = type; ret =board_usb_init (priv->portnr, priv->init_type);
@@ -766,7 +770,7 @@ int ehci_usb_remove(struct udevice *dev)ehci_deregister (dev); -return board_usb_cleanup (dev->seq, priv->init_type); +return board_usb_cleanup (dev->req_seq, priv->init_type); }static const struct udevice_id mx6_usb_ids[] = {
Signature · 1 line
2.16.4
PATCH 5/7 usb: ehci-mx6: fix controller index for imx8m and imx8
On 6/29/20 4:13 AM, Peng Fan wrote:
[...]
Quoted 5 lines
drivers/usb/host/ehci-mx6.c +0
-0
drivers/usb/host/ehci-mx6.c static int ehci_usb_bind(struct udevice *dev) · line 694
Quoted 9 lines
drivers/usb/host/ehci-mx6.c +5
-1@@ -687,7 +687,11 @@ static int ehci_usb_bind(struct udevice *dev)* With these changes in place, the ad-hoc indexing goes away and * the driver is fully converted to DT probing. */ -u32 controller_spacing =is_mx7 () ?0x10000 :0x200 ; +u32 controller_spacing; +if (IS_ENABLED (CONFIG_MX6 )) + controller_spacing =0x200 ; +else + controller_spacing =0x10000 ;
This looks related to this problem:501547cec1 ("usb: ehci-mx6: Fix bus enumeration for DM case") Maybe instead of adding to the problem, it would make sense to convert the driver to DM fully and then this problem with figuring out offsets would go away ?
PATCH 6/7 usb: ehci-mx6: Enable iMX EHCI driver for iMX8M Nano
In reply to Peng FanFrom: Ye Li <[email protected]>
Add the IMX8MN to the EHCI-MX7 kconfig dependency.
--- drivers/usb/host/Kconfig | 2 +- drivers/usb/host/ehci-mx6.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
drivers/usb/host/Kconfig +1 -1
@@ -147,7 +147,7 @@ config USB_EHCI_MX6 config USB_EHCI_MX7 bool "Support for i.MX7 on-chip EHCI USB controller" - depends on ARCH_MX7 || IMX8MM + depends on ARCH_MX7 || IMX8MM || IMX8MN default y ---help--- Enables support for the on-chip EHCI controller on i.MX7 SoCs.
drivers/usb/host/ehci-mx6.c +1 -1
@@ -620,7 +620,7 @@ static int ehci_usb_phy_mode(struct udevice *dev) plat->init_type =USB_INIT_DEVICE ; else plat->init_type = USB_INIT_HOST; - }else if (is_mx7 () ||is_imx8mm ()) { + }else if (is_mx7 () ||is_imx8mm () ||is_imx8mn ()) { phy_status = (void __iomem *)(addr +USBNC_PHY_STATUS_OFFSET ); val =readl (phy_status);
Signature · 1 line
2.16.4
PATCH 7/7 usb: ehci-mx6: configure usb out of suspend state
In reply to Peng FanWhen moving to support partition reboot or android auto on XEN, linux kernel will runs into runtime suspend state, and the usb will be configured to low power suspend state by Linux.
Then we reboot and runs into U-Boot, however the usb already in suspended state and uboot not able to lock the phy pll, after clearing PHCD to out of suspended state, the phy pll could be locked and fastboot works.
--- drivers/usb/host/ehci-mx6.c | 7 +++++++ 1 file changed, 7 insertions(+)
drivers/usb/host/ehci-mx6.c +7 -0
@@ -438,10 +438,17 @@ int __weak board_ehci_power(int port, int on)int ehci_mx6_common_init (struct usb_ehci *ehci,int index) {int ret; +u32 portsc;enable_usboh3_clk (1 );mdelay (1 ); + portsc =readl (&ehci->portsc); +if (portsc &PORT_PTS_PHCD ) { +debug ("suspended: portsc %x, enabled it.\n" , portsc); +clrbits_le32 (&ehci->portsc,PORT_PTS_PHCD ); + } +/* Do board specific initialization */ ret =board_ehci_hcd_init (index);if (ret)
Signature · 1 line
2.16.4
PATCH 1/7 usb: ehci-mx6: Add powerup_fixup implementation
In reply to Peng FanOn 6/29/20 4:13 AM, Peng Fan wrote:
[...]
Quoted 8 lines
drivers/usb/host/ehci-mx6.c +8
-0+static void ehci_mx6_powerup_fixup (struct ehci_ctrl *ctrl,uint32_t *status_reg, +uint32_t *reg) +{ +u32 result; +int usec =2000 ; + +mdelay (50 ); +
drivers/usb/host/ehci-mx6.c int usb_phy_mode(int port) · line 287
Quoted 10 lines
drivers/usb/host/ehci-mx6.c +10
-0+do { + result =ehci_readl (status_reg); +udelay (5 ); +if (!(result &EHCI_PS_PR )) +break ; + usec--; + }while (usec >0 ); + + *reg =ehci_readl (status_reg); +}
Please use wait_for_bit*() . Also, is the 50 mS delay upfront required or can this be wait_for_bit with 60000 uS timeout ?
PATCH 1/7 usb: ehci-mx6: Add powerup_fixup implementation
In reply to Peng FanHi Peng, Marek
Quoted 14 lines
From: Ye Li <[email protected]>
When doing port reset, the PR bit of PORTSC1 will be automatically cleared by our IP, but standard EHCI needs explicit clear by software. The EHCI-HCD driver follow the EHCI specification, so after 50ms wait, it clear the PR bit by writting to the PORTSC1 register with value loaded before setting PR.
This sequence is ok for our IP when the delay time is exact. But when the timer is slower, some bits like PE, PSPD have been set by controller automatically after the PR is automatically cleared. So the writing to the PORTSC1 will overwrite these bits set by controller. And eventually the driver gets wrong status.
Quoted 5 lines
We implement the
powerup_fixupoperation which delays 50ms and will check the PR until it is cleared by controller. And will update the reg value which is written to PORTSC register by EHCI-HCD driver. This is much safer than depending on the delay time to be accurate and aligining with controller's behaiver.
Is there any plan for a follow up for this patch set?
On my imx6q - kp_tpc70 board I can observe that there are some issues when trying to read data from USB [*]:
Booting update from usb ...
starting USB...
Bus usb at 2184200: USB EHCI 1.00
scanning bus usb at 2184200 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
EHCI timed out on TD - token=0x1f8c80
EHCI timed out on TD - token=0x1f8c80
Peng do you see similar issue when you test it on your iMX8?
The test is very simple - just put on a pendrive a fitImage and initramfs and try to boot with it. In my case it will hang at least once per ten attempts.
Note:
[*] - this is a similar issue to one, which I had on the iMX53 controller. However, Marek's patch fixed it on imx53:
"usb: Keep async schedule running only across mass storage xfers"
SHA1: 31232de07ef2bd97ff67625976eecd97eeb1b
Quoted 59 lines
Signed-off-by Ye Li <[email protected]>Signed-off-by Peng Fan <[email protected]>--- drivers/usb/host/ehci-mx6.c | 28 +++++++++++++++++++++++++++- 1 file changed, 27 insertions(+), 1 deletion(-)drivers/usb/host/ehci-mx6.c +19
-0@@ -267,6 +267,25 @@ int usb_phy_mode(int port) }#endif +static void ehci_mx6_powerup_fixup (struct ehci_ctrl *ctrl,uint32_t *status_reg, +uint32_t *reg) +{ +u32 result; +int usec =2000 ; + +mdelay (50 ); + +do { + result =ehci_readl (status_reg); +udelay (5 ); +if (!(result &EHCI_PS_PR )) +break ; + usec--; + }while (usec >0 ); + + *reg =ehci_readl (status_reg); +} +static void usb_oc_config (int index) {#if
defined(CONFIG_MX6)drivers/usb/host/ehci-mx6.c +6
-0@@ -366,6 +385,10 @@ int ehci_mx6_common_init(struct usb_ehci *ehci, int index) }#if !CONFIG_IS_ENABLED (DM_USB ) +static const struct ehci_ops mx6_ehci_ops = { + .powerup_fixup = ehci_mx6_powerup_fixup, +}; +int ehci_hcd_init (int index,enum usb_init_type init,struct ehci_hccr **hccr,struct ehci_hcor **hcor) {@@ -394,6 +417,8 @@ int ehci_hcd_init(int index, enum usb_init_type init, if (ret)return ret; +ehci_set_controller_priv (index,NULL , &mx6_ehci_ops); + type =board_usb_phy_mode (index);if (hccr && hcor) {
drivers/usb/host/ehci-mx6.c static int mx6_init_after_reset(struct ehci_ctrl · line 499
Quoted 9 lines
drivers/usb/host/ehci-mx6.c +2
-1@@ -467,7 +492,8 @@ static int mx6_init_after_reset(struct ehci_ctrl *dev) }static const struct ehci_ops mx6_ehci_ops = { - .init_after_reset = mx6_init_after_reset + .powerup_fixup = ehci_mx6_powerup_fixup, + .init_after_reset = mx6_init_after_reset };static int ehci_usb_phy_mode (struct udevice *dev)
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200824/822a56aa/attachment.sig>