Skip to contentSkip to conversation

Use hugepages to map kernel mem on 8xx

PATCH In review Christophe Leroy 3 participants 51 messages May 19, 2020 – Jun 9, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

v4 cover Use hugepages to map kernel mem on 8xx

The main purpose of this big series is to:
- reorganise huge page handling to avoid using mm_slices.
- use huge pages to map kernel memory on the 8xx.

The 8xx supports 4 page sizes: 4k, 16k, 512k and 8M.
It uses 2 Level page tables, PGD having 1024 entries, each entry covering 4M address space. Then each page table has 1024 entries.

At the time being, page sizes are managed in PGD entries, implying the use of mm_slices as it can't mix several pages of the same size in one page table.

The first purpose of this series is to reorganise things so that standard page tables can also handle 512k pages. This is done by adding a new _PAGE_HUGE flag which will be copied into the Level 1 entry in the TLB miss handler. That done, we have 2 types of pages:
- PGD entries to regular page tables handling 4k/16k and 512k pages
- PGD entries to hugepd tables handling 8M pages.

There is no need to mix 8M pages with other sizes, because a 8M page will use more than what a single PGD covers.

Then comes the second purpose of this series. At the time being, the 8xx has implemented special handling in the TLB miss handlers in order to transparently map kernel linear address space and the IMMR using huge pages by building the TLB entries in assembly at the time of the exception.

As mm_slices is only for user space pages, and also because it would anyway not be convenient to slice kernel address space, it was not possible to use huge pages for kernel address space. But after step one of the series, it is now more flexible to use huge pages.

This series drop all assembly 'just in time' handling of huge pages and use huge pages in page tables instead.

Once the above is done, then comes icing on the cake:
- Use huge pages for KASAN shadow mapping
- Allow pinned TLBs with strict kernel rwx
- Allow pinned TLBs with debug pagealloc

Then, last but not least, those modifications for the 8xx allows the following improvement on book3s/32:
- Mapping KASAN shadow with BATs
- Allowing BATs with debug pagealloc

All this allows to considerably simplify TLB miss handlers and associated initialisation. The overhead of reading page tables is negligible compared to the reduction of the miss handlers.

While we were at touching pte_update(), some cleanup was done there too.

Tested widely on 8xx and 832x. Boot tested on QEMU MAC99.

Changes in v4:
- Rebased on top of powerpc/next following the merge of prefix instructions series.

Changes in v3:
- Fixed the handling of leaf pages page size which didn't build on PPC64 and was invisibily bogus on PPC32 (patch 12)

Changes in v2:
- Selecting HUGETLBFS instead of HUGETLB_PAGE which leads to link failure.
- Rebase on latest powerpc/merge branch
- Reworked the way TLB 28 to 31 are pinned because it was not working.

Christophe Leroy (45):
powerpc/kasan: Fix error detection on memory allocation powerpc/kasan: Fix issues by lowering KASAN_SHADOW_END powerpc/kasan: Fix shadow pages allocation failure powerpc/kasan: Remove unnecessary page table locking powerpc/kasan: Refactor update of early shadow mappings powerpc/kasan: Declare kasan_init_region() weak powerpc/ptdump: Limit size of flags text to 1/2 chars on PPC32 powerpc/ptdump: Reorder flags
powerpc/ptdump: Add _PAGE_COHERENT flag
powerpc/ptdump: Display size of BATs
powerpc/ptdump: Standardise display of BAT flags powerpc/ptdump: Properly handle non standard page size powerpc/ptdump: Handle hugepd at PGD level
powerpc/32s: Don't warn when mapping RO data ROX. powerpc/mm: Allocate static page tables for fixmap powerpc/mm: Fix conditions to perform MMU specific management by
blocks on PPC32.
powerpc/mm: PTE_ATOMIC_UPDATES is only for 40x powerpc/mm: Refactor pte_update() on nohash/32 powerpc/mm: Refactor pte_update() on book3s/32 powerpc/mm: Standardise __ptep_test_and_clear_young() params between

    PPC32 and PPC64

powerpc/mm: Standardise pte_update() prototype between PPC32 and PPC64 powerpc/mm: Create a dedicated pte_update() for 8xx powerpc/mm: Reduce hugepd size for 8M hugepages on 8xx powerpc/8xx: Drop CONFIG_8xx_COPYBACK option
powerpc/8xx: Prepare handlers for _PAGE_HUGE for 512k pages. powerpc/8xx: Manage 512k huge pages as standard pages. powerpc/8xx: Only 8M pages are hugepte pages now powerpc/8xx: MM_SLICE is not needed anymore
powerpc/8xx: Move PPC_PIN_TLB options into 8xx Kconfig powerpc/8xx: Add function to set pinned TLBs
powerpc/8xx: Don't set IMMR map anymore at boot powerpc/8xx: Always pin TLBs at startup.
powerpc/8xx: Drop special handling of Linear and IMMR mappings in I/D
TLB handlers
powerpc/8xx: Remove now unused TLB miss functions powerpc/8xx: Move DTLB perf handling closer.
powerpc/mm: Don't be too strict with _etext alignment on PPC32 powerpc/8xx: Refactor kernel address boundary comparison powerpc/8xx: Add a function to early map kernel via huge pages powerpc/8xx: Map IMMR with a huge page
powerpc/8xx: Map linear memory with huge pages powerpc/8xx: Allow STRICT_KERNEL_RwX with pinned TLB powerpc/8xx: Allow large TLBs with DEBUG_PAGEALLOC powerpc/8xx: Implement dedicated kasan_init_region() powerpc/32s: Allow mapping with BATs with DEBUG_PAGEALLOC powerpc/32s: Implement dedicated kasan_init_region()

 arch/powerpc/Kconfig                          |  62 +--
 arch/powerpc/configs/adder875_defconfig       |   1 -
 arch/powerpc/configs/ep88xc_defconfig         |   1 -
 arch/powerpc/configs/mpc866_ads_defconfig     |   1 -
 arch/powerpc/configs/mpc885_ads_defconfig     |   1 -
 arch/powerpc/configs/tqm8xx_defconfig         |   1 -
 arch/powerpc/include/asm/book3s/32/pgtable.h  |  78 ++--
 arch/powerpc/include/asm/fixmap.h             |   4 +
 arch/powerpc/include/asm/hugetlb.h            |   4 -
 arch/powerpc/include/asm/kasan.h              |  10 +-
 .../include/asm/nohash/32/hugetlb-8xx.h       |  32 +-
 arch/powerpc/include/asm/nohash/32/mmu-8xx.h  |  74 +---
 arch/powerpc/include/asm/nohash/32/pgtable.h  | 104 +++--
 arch/powerpc/include/asm/nohash/32/pte-8xx.h  |   4 +-
 arch/powerpc/include/asm/nohash/32/slice.h    |  20 -
 arch/powerpc/include/asm/nohash/64/pgtable.h  |  28 +-
 arch/powerpc/include/asm/nohash/pgtable.h     |   2 +-
 arch/powerpc/include/asm/pgtable.h            |   2 +
 arch/powerpc/include/asm/slice.h              |   2 -
 arch/powerpc/kernel/head_8xx.S                | 354 ++++++++----------
 arch/powerpc/kernel/setup_32.c                |   2 +-
 arch/powerpc/kernel/vmlinux.lds.S             |   3 +-
 arch/powerpc/mm/book3s32/mmu.c                |  12 +-
 arch/powerpc/mm/hugetlbpage.c                 |  41 +-
 arch/powerpc/mm/init_32.c                     |  12 +-
 arch/powerpc/mm/kasan/8xx.c                   |  74 ++++
 arch/powerpc/mm/kasan/Makefile                |   2 +
 arch/powerpc/mm/kasan/book3s_32.c             |  57 +++
 arch/powerpc/mm/kasan/kasan_init_32.c         |  88 ++---
 arch/powerpc/mm/mmu_decl.h                    |   4 +
 arch/powerpc/mm/nohash/8xx.c                  | 226 ++++++-----
 arch/powerpc/mm/pgtable.c                     |  34 +-
 arch/powerpc/mm/pgtable_32.c                  |  22 +-
 arch/powerpc/mm/ptdump/8xx.c                  |  52 +--
 arch/powerpc/mm/ptdump/bats.c                 |  41 +-
 arch/powerpc/mm/ptdump/ptdump.c               |  71 +++-
 arch/powerpc/mm/ptdump/ptdump.h               |   3 +
 arch/powerpc/mm/ptdump/shared.c               |  58 +--
 arch/powerpc/perf/8xx-pmu.c                   |  10 -
 arch/powerpc/platforms/8xx/Kconfig            |  50 ++-
 arch/powerpc/platforms/Kconfig.cputype        |   2 +-
 arch/powerpc/sysdev/cpm_common.c              |   2 +
 42 files changed, 853 insertions(+), 798 deletions(-)
 delete mode 100644 arch/powerpc/include/asm/nohash/32/slice.h
 create mode 100644 arch/powerpc/mm/kasan/8xx.c
 create mode 100644 arch/powerpc/mm/kasan/book3s_32.c
Signature · 1 line
2.25.0
#1 lore raw

PATCH v4 1/45 powerpc/kasan: Fix error detection on memory allocation

In case (k_start & PAGE_MASK) doesn't equal (kstart), 'va' will never be NULL allthough 'block' is NULL

Check the return of memblock_alloc() directly instead of the resulting address in the loop.

Fixes 509cd3f2b473 ("powerpc/32: Simplify KASAN init")
---
 arch/powerpc/mm/kasan/kasan_init_32.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)
arch/powerpc/mm/kasan/kasan_init_32.c +2 -3
index cbcad369fcb2..8b15fe09b967 100644
@@ -76,15 +76,14 @@ static int __init kasan_init_region(void *start, size_t size)
 		return ret;
 
 	block = memblock_alloc(k_end - k_start, PAGE_SIZE);
+	if (!block)
+		return -ENOMEM;
 
 	for (k_cur = k_start & PAGE_MASK; k_cur < k_end; k_cur += PAGE_SIZE) {
 		pmd_t *pmd = pmd_ptr_k(k_cur);
 		void *va = block + k_cur - k_start;
 		pte_t pte = pfn_pte(PHYS_PFN(__pa(va)), PAGE_KERNEL);
 
-		if (!va)
-			return -ENOMEM;
-
 		__set_pte_at(&init_mm, k_cur, pte_offset_kernel(pmd, k_cur), pte, 0);
 	}
 	flush_tlb_kernel_range(k_start, k_end);
Signature · 1 line
2.25.0
#2 lore raw

PATCH v4 2/45 powerpc/kasan: Fix issues by lowering KASAN_SHADOW_END

In reply to Christophe Leroy

At the time being, KASAN_SHADOW_END is 0x100000000, which is 0 in 32 bits representation.

This leads to a couple of issues:
- kasan_remap_early_shadow_ro() does nothing because the comparison k_cur < k_end is always false.
- In ptdump, address comparison for markers display fails and the marker's name is printed at the start of the KASAN area instead of being printed at the end.

However, there is no need to shadow the KASAN shadow area itself, so the KASAN shadow area can stop shadowing memory at the start of itself.

With a PAGE_OFFSET set to 0xc0000000, KASAN shadow area is then going from 0xf8000000 to 0xff000000.

Fixes cbd18991e24f ("powerpc/mm: Fix an Oops in kasan_mmu_init()")
---
 arch/powerpc/include/asm/kasan.h | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)
arch/powerpc/include/asm/kasan.h +1 -3
index fbff9ff9032e..fc900937f653 100644
@@ -23,9 +23,7 @@
 
 #define KASAN_SHADOW_OFFSET	ASM_CONST(CONFIG_KASAN_SHADOW_OFFSET)
 
-#define KASAN_SHADOW_END	0UL
-
-#define KASAN_SHADOW_SIZE	(KASAN_SHADOW_END - KASAN_SHADOW_START)
+#define KASAN_SHADOW_END	(-(-KASAN_SHADOW_START >> KASAN_SHADOW_SCALE_SHIFT))
 
 #ifdef CONFIG_KASAN
 void kasan_early_init(void);
Signature · 1 line
2.25.0
#3 lore raw

PATCH v4 3/45 powerpc/kasan: Fix shadow pages allocation failure

In reply to Christophe Leroy

Doing kasan pages allocation in MMU_init is too early, kernel doesn't have access yet to the entire memory space and memblock_alloc() fails when the kernel is a bit big.

Do it from kasan_init() instead.

Fixes 2edb16efc899 ("powerpc/32: Add KASAN support")
---
 arch/powerpc/include/asm/kasan.h      | 2 --
 arch/powerpc/mm/init_32.c             | 2 --
 arch/powerpc/mm/kasan/kasan_init_32.c | 4 +++-
 3 files changed, 3 insertions(+), 5 deletions(-)
arch/powerpc/include/asm/kasan.h +0 -2
index fc900937f653..4769bbf7173a 100644
@@ -27,12 +27,10 @@
 
 #ifdef CONFIG_KASAN
 void kasan_early_init(void);
-void kasan_mmu_init(void);
 void kasan_init(void);
 void kasan_late_init(void);
 #else
 static inline void kasan_init(void) { }
-static inline void kasan_mmu_init(void) { }
 static inline void kasan_late_init(void) { }
 #endif
 
arch/powerpc/mm/init_32.c +0 -2
index 872df48ae41b..a6991ef8727d 100644
@@ -170,8 +170,6 @@ void __init MMU_init(void)
 	btext_unmap();
 #endif
 
-	kasan_mmu_init();
-
 	setup_kup();
 
 	/* Shortly after that, the entire linear mapping will be available */
arch/powerpc/mm/kasan/kasan_init_32.c +3 -1
index 8b15fe09b967..b7c287adfd59 100644
@@ -131,7 +131,7 @@ static void __init kasan_unmap_early_shadow_vmalloc(void)
 	flush_tlb_kernel_range(k_start, k_end);
 }
 
-void __init kasan_mmu_init(void)
+static void __init kasan_mmu_init(void)
 {
 	int ret;
 	struct memblock_region *reg;
@@ -159,6 +159,8 @@ void __init kasan_mmu_init(void)
 
 void __init kasan_init(void)
 {
+	kasan_mmu_init();
+
 	kasan_remap_early_shadow_ro();
 
 	clear_page(kasan_early_shadow_page);
Signature · 1 line
2.25.0
#4 lore raw

PATCH v4 4/45 powerpc/kasan: Remove unnecessary page table locking

In reply to Christophe Leroy

Commit 45ff3c559585 ("powerpc/kasan: Fix parallel loading of modules.") added spinlocks to manage parallele module loading.

Since then commit 47febbeeec44 ("powerpc/32: Force KASAN_VMALLOC for modules") converted the module loading to KASAN_VMALLOC.

The spinlocking has then become unneeded and can be removed to simplify kasan_init_shadow_page_tables()

Also remove inclusion of linux/moduleloader.h and linux/vmalloc.h which are not needed anymore since the removal of modules management.

---
 arch/powerpc/mm/kasan/kasan_init_32.c | 19 ++++---------------
 1 file changed, 4 insertions(+), 15 deletions(-)
arch/powerpc/mm/kasan/kasan_init_32.c +4 -15
index b7c287adfd59..91e2ade75192 100644
@@ -5,9 +5,7 @@
 #include <linux/kasan.h>
 #include <linux/printk.h>
 #include <linux/memblock.h>
-#include <linux/moduleloader.h>
 #include <linux/sched/task.h>
-#include <linux/vmalloc.h>
 #include <asm/pgalloc.h>
 #include <asm/code-patching.h>
 #include <mm/mmu_decl.h>
@@ -34,31 +32,22 @@ static int __init kasan_init_shadow_page_tables(unsigned long k_start, unsigned
 {
 	pmd_t *pmd;
 	unsigned long k_cur, k_next;
-	pte_t *new = NULL;
 
 	pmd = pmd_ptr_k(k_start);
 
 	for (k_cur = k_start; k_cur != k_end; k_cur = k_next, pmd++) {
+		pte_t *new;
+
 		k_next = pgd_addr_end(k_cur, k_end);
 		if ((void *)pmd_page_vaddr(*pmd) != kasan_early_shadow_pte)
 			continue;
 
-		if (!new)
-			new = memblock_alloc(PTE_FRAG_SIZE, PTE_FRAG_SIZE);
+		new = memblock_alloc(PTE_FRAG_SIZE, PTE_FRAG_SIZE);
 
 		if (!new)
 			return -ENOMEM;
 		kasan_populate_pte(new, PAGE_KERNEL);
-
-		smp_wmb(); /* See comment in __pte_alloc */
-
-		spin_lock(&init_mm.page_table_lock);
-			/* Has another populated it ? */
-		if (likely((void *)pmd_page_vaddr(*pmd) == kasan_early_shadow_pte)) {
-			pmd_populate_kernel(&init_mm, pmd, new);
-			new = NULL;
-		}
-		spin_unlock(&init_mm.page_table_lock);
+		pmd_populate_kernel(&init_mm, pmd, new);
 	}
 	return 0;
 }
Signature · 1 line
2.25.0
#5 lore raw

PATCH v4 5/45 powerpc/kasan: Refactor update of early shadow mappings

In reply to Christophe Leroy

kasan_remap_early_shadow_ro() and kasan_unmap_early_shadow_vmalloc() are both updating the early shadow mapping: the first one sets the mapping read-only while the other clears the mapping.

Refactor and create kasan_update_early_region()

---
 arch/powerpc/mm/kasan/kasan_init_32.c | 39 +++++++++++++--------------
 1 file changed, 18 insertions(+), 21 deletions(-)
arch/powerpc/mm/kasan/kasan_init_32.c +18 -21
index 91e2ade75192..10481d904fea 100644
@@ -79,45 +79,42 @@ static int __init kasan_init_region(void *start, size_t size)
 	return 0;
 }
 
-static void __init kasan_remap_early_shadow_ro(void)
+static void __init
+kasan_update_early_region(unsigned long k_start, unsigned long k_end, pte_t pte)
 {
-	pgprot_t prot = kasan_prot_ro();
-	unsigned long k_start = KASAN_SHADOW_START;
-	unsigned long k_end = KASAN_SHADOW_END;
 	unsigned long k_cur;
 	phys_addr_t pa = __pa(kasan_early_shadow_page);
 
-	kasan_populate_pte(kasan_early_shadow_pte, prot);
-
-	for (k_cur = k_start & PAGE_MASK; k_cur != k_end; k_cur += PAGE_SIZE) {
+	for (k_cur = k_start; k_cur != k_end; k_cur += PAGE_SIZE) {
 		pmd_t *pmd = pmd_ptr_k(k_cur);
 		pte_t *ptep = pte_offset_kernel(pmd, k_cur);
 
 		if ((pte_val(*ptep) & PTE_RPN_MASK) != pa)
 			continue;
 
-		__set_pte_at(&init_mm, k_cur, ptep, pfn_pte(PHYS_PFN(pa), prot), 0);
+		__set_pte_at(&init_mm, k_cur, ptep, pte, 0);
 	}
-	flush_tlb_kernel_range(KASAN_SHADOW_START, KASAN_SHADOW_END);
+
+	flush_tlb_kernel_range(k_start, k_end);
 }
 
-static void __init kasan_unmap_early_shadow_vmalloc(void)
+static void __init kasan_remap_early_shadow_ro(void)
 {
-	unsigned long k_start = (unsigned long)kasan_mem_to_shadow((void *)VMALLOC_START);
-	unsigned long k_end = (unsigned long)kasan_mem_to_shadow((void *)VMALLOC_END);
-	unsigned long k_cur;
+	pgprot_t prot = kasan_prot_ro();
 	phys_addr_t pa = __pa(kasan_early_shadow_page);
 
-	for (k_cur = k_start & PAGE_MASK; k_cur < k_end; k_cur += PAGE_SIZE) {
-		pmd_t *pmd = pmd_offset(pud_offset(pgd_offset_k(k_cur), k_cur), k_cur);
-		pte_t *ptep = pte_offset_kernel(pmd, k_cur);
+	kasan_populate_pte(kasan_early_shadow_pte, prot);
 
-		if ((pte_val(*ptep) & PTE_RPN_MASK) != pa)
-			continue;
+	kasan_update_early_region(KASAN_SHADOW_START, KASAN_SHADOW_END,
+				  pfn_pte(PHYS_PFN(pa), prot));
+}
 
-		__set_pte_at(&init_mm, k_cur, ptep, __pte(0), 0);
-	}
-	flush_tlb_kernel_range(k_start, k_end);
+static void __init kasan_unmap_early_shadow_vmalloc(void)
+{
+	unsigned long k_start = (unsigned long)kasan_mem_to_shadow((void *)VMALLOC_START);
+	unsigned long k_end = (unsigned long)kasan_mem_to_shadow((void *)VMALLOC_END);
+
+	kasan_update_early_region(k_start, k_end, __pte(0));
 }
 
 static void __init kasan_mmu_init(void)
Signature · 1 line
2.25.0
#6 lore raw

PATCH v4 6/45 powerpc/kasan: Declare kasan_init_region() weak

In reply to Christophe Leroy

In order to alloc sub-arches to alloc KASAN regions using optimised methods (Huge pages on 8xx, BATs on BOOK3S, ...), declare kasan_init_region() weak.

Also make kasan_init_shadow_page_tables() accessible from outside, so that it can be called from the specific kasan_init_region() functions if needed.

And populate remaining KASAN address space only once performed the region mapping, to allow 8xx to allocate hugepd instead of standard page tables for mapping via 8M hugepages.

---
 arch/powerpc/include/asm/kasan.h      |  3 +++
 arch/powerpc/mm/kasan/kasan_init_32.c | 21 +++++++++++----------
 2 files changed, 14 insertions(+), 10 deletions(-)
arch/powerpc/include/asm/kasan.h +3 -0
index 4769bbf7173a..107a24c3f7b3 100644
@@ -34,5 +34,8 @@ static inline void kasan_init(void) { }
 static inline void kasan_late_init(void) { }
 #endif
 
+int kasan_init_shadow_page_tables(unsigned long k_start, unsigned long k_end);
+int kasan_init_region(void *start, size_t size);
+
 #endif /* __ASSEMBLY */
 #endif
arch/powerpc/mm/kasan/kasan_init_32.c +11 -10
index 10481d904fea..76d418af4ce8 100644
@@ -28,7 +28,7 @@ static void __init kasan_populate_pte(pte_t *ptep, pgprot_t prot)
 		__set_pte_at(&init_mm, va, ptep, pfn_pte(PHYS_PFN(pa), prot), 0);
 }
 
-static int __init kasan_init_shadow_page_tables(unsigned long k_start, unsigned long k_end)
+int __init kasan_init_shadow_page_tables(unsigned long k_start, unsigned long k_end)
 {
 	pmd_t *pmd;
 	unsigned long k_cur, k_next;
@@ -52,7 +52,7 @@ static int __init kasan_init_shadow_page_tables(unsigned long k_start, unsigned
 	return 0;
 }
 
-static int __init kasan_init_region(void *start, size_t size)
+int __init __weak kasan_init_region(void *start, size_t size)
 {
 	unsigned long k_start = (unsigned long)kasan_mem_to_shadow(start);
 	unsigned long k_end = (unsigned long)kasan_mem_to_shadow(start + size);
@@ -122,14 +122,6 @@ static void __init kasan_mmu_init(void)
 	int ret;
 	struct memblock_region *reg;
 
-	if (early_mmu_has_feature(MMU_FTR_HPTE_TABLE) ||
-	    IS_ENABLED(CONFIG_KASAN_VMALLOC)) {
-		ret = kasan_init_shadow_page_tables(KASAN_SHADOW_START, KASAN_SHADOW_END);
-
-		if (ret)
-			panic("kasan: kasan_init_shadow_page_tables() failed");
-	}
-
 	for_each_memblock(memory, reg) {
 		phys_addr_t base = reg->base;
 		phys_addr_t top = min(base + reg->size, total_lowmem);
@@ -141,6 +133,15 @@ static void __init kasan_mmu_init(void)
 		if (ret)
 			panic("kasan: kasan_init_region() failed");
 	}
+
+	if (early_mmu_has_feature(MMU_FTR_HPTE_TABLE) ||
+	    IS_ENABLED(CONFIG_KASAN_VMALLOC)) {
+		ret = kasan_init_shadow_page_tables(KASAN_SHADOW_START, KASAN_SHADOW_END);
+
+		if (ret)
+			panic("kasan: kasan_init_shadow_page_tables() failed");
+	}
+
 }
 
 void __init kasan_init(void)
Signature · 1 line
2.25.0
#7 lore raw

PATCH v4 7/45 powerpc/ptdump: Limit size of flags text to 1/2 chars on PPC32

In reply to Christophe Leroy

In order to have all flags fit on a 80 chars wide screen, reduce the flags to 1 char (2 where ambiguous).

No cache is 'i'
User is 'ur' (Supervisor would be sr)
Shared (for 8xx) becomes 'sh' (it was 'user' when not shared but that was ambiguous because that's not entirely right)

---
 arch/powerpc/mm/ptdump/8xx.c    | 33 ++++++++++++++++---------------
 arch/powerpc/mm/ptdump/shared.c | 35 +++++++++++++++++----------------
 2 files changed, 35 insertions(+), 33 deletions(-)
arch/powerpc/mm/ptdump/8xx.c +17 -16
index 9e2d8e847d6e..ca9ce94672f5 100644
@@ -12,9 +12,9 @@
 static const struct flag_info flag_array[] = {
 	{
 		.mask	= _PAGE_SH,
-		.val	= 0,
-		.set	= "user",
-		.clear	= "    ",
+		.val	= _PAGE_SH,
+		.set	= "sh",
+		.clear	= "  ",
 	}, {
 		.mask	= _PAGE_RO | _PAGE_NA,
 		.val	= 0,
@@ -30,37 +30,38 @@ static const struct flag_info flag_array[] = {
 	}, {
 		.mask	= _PAGE_EXEC,
 		.val	= _PAGE_EXEC,
-		.set	= " X ",
-		.clear	= "   ",
+		.set	= "x",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_PRESENT,
 		.val	= _PAGE_PRESENT,
-		.set	= "present",
-		.clear	= "       ",
+		.set	= "p",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_GUARDED,
 		.val	= _PAGE_GUARDED,
-		.set	= "guarded",
-		.clear	= "       ",
+		.set	= "g",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_DIRTY,
 		.val	= _PAGE_DIRTY,
-		.set	= "dirty",
-		.clear	= "     ",
+		.set	= "d",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_ACCESSED,
 		.val	= _PAGE_ACCESSED,
-		.set	= "accessed",
-		.clear	= "        ",
+		.set	= "a",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_NO_CACHE,
 		.val	= _PAGE_NO_CACHE,
-		.set	= "no cache",
-		.clear	= "        ",
+		.set	= "i",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_SPECIAL,
 		.val	= _PAGE_SPECIAL,
-		.set	= "special",
+		.set	= "s",
+		.clear	= " ",
 	}
 };
 
arch/powerpc/mm/ptdump/shared.c +18 -17
index f7ed2f187cb0..44a8a64a664f 100644
@@ -13,8 +13,8 @@ static const struct flag_info flag_array[] = {
 	{
 		.mask	= _PAGE_USER,
 		.val	= _PAGE_USER,
-		.set	= "user",
-		.clear	= "    ",
+		.set	= "ur",
+		.clear	= "  ",
 	}, {
 		.mask	= _PAGE_RW,
 		.val	= _PAGE_RW,
@@ -23,42 +23,43 @@ static const struct flag_info flag_array[] = {
 	}, {
 		.mask	= _PAGE_EXEC,
 		.val	= _PAGE_EXEC,
-		.set	= " X ",
-		.clear	= "   ",
+		.set	= "x",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_PRESENT,
 		.val	= _PAGE_PRESENT,
-		.set	= "present",
-		.clear	= "       ",
+		.set	= "p",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_GUARDED,
 		.val	= _PAGE_GUARDED,
-		.set	= "guarded",
-		.clear	= "       ",
+		.set	= "g",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_DIRTY,
 		.val	= _PAGE_DIRTY,
-		.set	= "dirty",
-		.clear	= "     ",
+		.set	= "d",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_ACCESSED,
 		.val	= _PAGE_ACCESSED,
-		.set	= "accessed",
-		.clear	= "        ",
+		.set	= "a",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_WRITETHRU,
 		.val	= _PAGE_WRITETHRU,
-		.set	= "write through",
-		.clear	= "             ",
+		.set	= "w",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_NO_CACHE,
 		.val	= _PAGE_NO_CACHE,
-		.set	= "no cache",
-		.clear	= "        ",
+		.set	= "i",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_SPECIAL,
 		.val	= _PAGE_SPECIAL,
-		.set	= "special",
+		.set	= "s",
+		.clear	= " ",
 	}
 };
 
Signature · 1 line
2.25.0
#8 lore raw

Re: [PATCH v4 07/45] powerpc/ptdump: Limit size of flags text to 1/2 chars on PPC32

Quoted 2 lines · Christophe Leroy

In order to have all flags fit on a 80 chars wide screen, reduce the flags to 1 char (2 where ambiguous).

I don't love this, the output is less readable. Is fitting on an 80 char screen a real issue for you? I just make my terminal window bigger.

cheers

Quoted 10 lines

No cache is 'i'
User is 'ur' (Supervisor would be sr)
Shared (for 8xx) becomes 'sh' (it was 'user' when not shared but that was ambiguous because that's not entirely right)

---
 arch/powerpc/mm/ptdump/8xx.c    | 33 ++++++++++++++++---------------
 arch/powerpc/mm/ptdump/shared.c | 35 +++++++++++++++++----------------
 2 files changed, 35 insertions(+), 33 deletions(-)
#9 lore raw

Re: [PATCH v4 07/45] powerpc/ptdump: Limit size of flags text to 1/2 chars on PPC32

Le 25/05/2020 à 07:15, Michael Ellerman a écrit :

Quoted 6 lines
Quoted 2 lines · Christophe Leroy

In order to have all flags fit on a 80 chars wide screen, reduce the flags to 1 char (2 where ambiguous).

I don't love this, the output is less readable. Is fitting on an 80 char screen a real issue for you? I just make my terminal window bigger.

I don't have strong opinion about that, and the terminal can be made bigger.
I just don't like how messy it is, some flags are so big that they hide other ones and getting it more ordered and more compact helped me during all the verifications I did with this series, but we can leave it as is if you prefer.

Would you like a v5 without patches 7 and 8 ? Or I can just resend the patches that will be impacted, that is 9 and 38 ?

Without the changes I get:

---[ Start of kernel VM ]---

0xc0000000-0xc0ffffff  0x00000000        16M   huge  shared  r    X present                  accessed
0xc1000000-0xc7ffffff  0x01000000       112M   huge  shared  rw present           dirty  accessed
---[ vmalloc() Area ]---
0xc9000000-0xc9003fff  0x050e4000        16K         shared  rw present           dirty  accessed
0xc9008000-0xc900bfff  0x050ec000        16K         shared  rw present           dirty  accessed
0xc9010000-0xc9013fff  0xd0000000        16K         shared  rw present  guarded  dirty  accessed  no cache
0xc9018000-0xc901bfff  0x050f0000        16K         shared  rw present           dirty  accessed

---[ Fixmap start ]---
0xf7f00000-0xf7f7ffff 0xff000000 512K huge shared rw present guarded dirty accessed no cache
---[ Fixmap end ]---
---[ kasan shadow mem start ]---

0xf8000000-0xf8ffffff  0x07000000        16M   huge  shared  rw present           dirty  accessed
0xf9000000-0xf91fffff [0x01288000]       16K         shared  r present                  accessed
0xf9200000-0xf9203fff  0x050e0000        16K         shared  rw present           dirty  accessed

With the change I get.

---[ Start of kernel VM ]---
0xc0000000-0xc0ffffff 0x00000000 16M h r x p sh
a
0xc1000000-0xc7ffffff 0x01000000 112M h rw p sh d a
---[ vmalloc() Area ]---

0xc9000000-0xc9003fff  0x050e4000        16K      rw     p        sh d  a
0xc9008000-0xc900bfff  0x050ec000        16K      rw     p        sh d  a
0xc9010000-0xc9013fff  0xd0000000        16K      rw     p  i  g  sh d  a
0xc9018000-0xc901bfff  0x050f0000        16K      rw     p        sh d  a

---[ Fixmap start ]---
0xf7f00000-0xf7f7ffff 0xff000000 512K h rw p i g sh d a
---[ Fixmap end ]---
---[ kasan shadow mem start ]---

0xf8000000-0xf8ffffff  0x07000000        16M   h  rw     p        sh d  a
0xf9000000-0xf91fffff [0x01288000]       16K      r      p        sh 

a
0xf9200000-0xf9203fff 0x050e0000 16K rw p sh d a

Christophe

Quoted 14 lines

cheers

Quoted 10 lines

No cache is 'i'
User is 'ur' (Supervisor would be sr)
Shared (for 8xx) becomes 'sh' (it was 'user' when not shared but that was ambiguous because that's not entirely right)

---
  arch/powerpc/mm/ptdump/8xx.c    | 33 ++++++++++++++++---------------
  arch/powerpc/mm/ptdump/shared.c | 35 +++++++++++++++++----------------
  2 files changed, 35 insertions(+), 33 deletions(-)
#10 lore raw

Re: [PATCH v4 07/45] powerpc/ptdump: Limit size of flags text to 1/2 chars on PPC32

Quoted 5 lines · Christophe Leroy

Le 25/05/2020 à 07:15, Michael Ellerman a écrit :

Quoted 4 lines
Quoted 2 lines · Christophe Leroy

In order to have all flags fit on a 80 chars wide screen, reduce the flags to 1 char (2 where ambiguous).

Quoted 8 lines
Quoted 2 lines

I don't love this, the output is less readable. Is fitting on an 80 char screen a real issue for you? I just make my terminal window bigger.

I don't have strong opinion about that, and the terminal can be made bigger. I just don't like how messy it is, some flags are so big that they hide other ones and getting it more ordered and more compact helped me during all the verifications I did with this series, but we can leave it as is if you prefer.

I think I do.

Quoted 2 lines

Would you like a v5 without patches 7 and 8 ? Or I can just resend the patches that will be impacted, that is 9 and 38 ?

I dropped 7 and 8 and then fixed up 9 and 38, it was easy enough.

I used "coherent" and "huge".

Quoted 10 lines

With the change I get.

---[ Start of kernel VM ]---

0xc0000000-0xc0ffffff  0x00000000        16M   h  r   x  p        sh     a
0xc1000000-0xc7ffffff  0x01000000       112M   h  rw     p        sh  d  a
---[ vmalloc() Area ]---
0xc9000000-0xc9003fff  0x050e4000        16K      rw     p        sh  d  a
0xc9008000-0xc900bfff  0x050ec000        16K      rw     p        sh  d  a
0xc9010000-0xc9013fff  0xd0000000        16K      rw     p  i  g  sh  d  a
0xc9018000-0xc901bfff  0x050f0000        16K      rw     p        sh  d  a

It's definitely more compact :)

But I worry no one other than you will be able to decipher it, without constantly referring back to the source code.

cheers

#11 lore raw

PATCH v4 8/45 powerpc/ptdump: Reorder flags

In reply to Christophe Leroy

Reorder flags in a more logical way:
- Page size (huge) first
- User
- RWX
- Present
- WIMG
- Special
- Dirty and Accessed

---
 arch/powerpc/mm/ptdump/8xx.c    | 30 +++++++++++++++---------------
 arch/powerpc/mm/ptdump/shared.c | 30 +++++++++++++++---------------
 2 files changed, 30 insertions(+), 30 deletions(-)
arch/powerpc/mm/ptdump/8xx.c +15 -15
index ca9ce94672f5..a3169677dced 100644
@@ -11,11 +11,6 @@
 
 static const struct flag_info flag_array[] = {
 	{
-		.mask	= _PAGE_SH,
-		.val	= _PAGE_SH,
-		.set	= "sh",
-		.clear	= "  ",
-	}, {
 		.mask	= _PAGE_RO | _PAGE_NA,
 		.val	= 0,
 		.set	= "rw",
@@ -37,11 +32,26 @@ static const struct flag_info flag_array[] = {
 		.val	= _PAGE_PRESENT,
 		.set	= "p",
 		.clear	= " ",
+	}, {
+		.mask	= _PAGE_NO_CACHE,
+		.val	= _PAGE_NO_CACHE,
+		.set	= "i",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_GUARDED,
 		.val	= _PAGE_GUARDED,
 		.set	= "g",
 		.clear	= " ",
+	}, {
+		.mask	= _PAGE_SH,
+		.val	= _PAGE_SH,
+		.set	= "sh",
+		.clear	= "  ",
+	}, {
+		.mask	= _PAGE_SPECIAL,
+		.val	= _PAGE_SPECIAL,
+		.set	= "s",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_DIRTY,
 		.val	= _PAGE_DIRTY,
@@ -52,16 +62,6 @@ static const struct flag_info flag_array[] = {
 		.val	= _PAGE_ACCESSED,
 		.set	= "a",
 		.clear	= " ",
-	}, {
-		.mask	= _PAGE_NO_CACHE,
-		.val	= _PAGE_NO_CACHE,
-		.set	= "i",
-		.clear	= " ",
-	}, {
-		.mask	= _PAGE_SPECIAL,
-		.val	= _PAGE_SPECIAL,
-		.set	= "s",
-		.clear	= " ",
 	}
 };
 
arch/powerpc/mm/ptdump/shared.c +15 -15
index 44a8a64a664f..dab5d8028a9b 100644
@@ -30,21 +30,6 @@ static const struct flag_info flag_array[] = {
 		.val	= _PAGE_PRESENT,
 		.set	= "p",
 		.clear	= " ",
-	}, {
-		.mask	= _PAGE_GUARDED,
-		.val	= _PAGE_GUARDED,
-		.set	= "g",
-		.clear	= " ",
-	}, {
-		.mask	= _PAGE_DIRTY,
-		.val	= _PAGE_DIRTY,
-		.set	= "d",
-		.clear	= " ",
-	}, {
-		.mask	= _PAGE_ACCESSED,
-		.val	= _PAGE_ACCESSED,
-		.set	= "a",
-		.clear	= " ",
 	}, {
 		.mask	= _PAGE_WRITETHRU,
 		.val	= _PAGE_WRITETHRU,
@@ -55,11 +40,26 @@ static const struct flag_info flag_array[] = {
 		.val	= _PAGE_NO_CACHE,
 		.set	= "i",
 		.clear	= " ",
+	}, {
+		.mask	= _PAGE_GUARDED,
+		.val	= _PAGE_GUARDED,
+		.set	= "g",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_SPECIAL,
 		.val	= _PAGE_SPECIAL,
 		.set	= "s",
 		.clear	= " ",
+	}, {
+		.mask	= _PAGE_DIRTY,
+		.val	= _PAGE_DIRTY,
+		.set	= "d",
+		.clear	= " ",
+	}, {
+		.mask	= _PAGE_ACCESSED,
+		.val	= _PAGE_ACCESSED,
+		.set	= "a",
+		.clear	= " ",
 	}
 };
 
Signature · 1 line
2.25.0
#12 lore raw

PATCH v4 9/45 powerpc/ptdump: Add _PAGE_COHERENT flag

In reply to Christophe Leroy

For platforms using shared.c (4xx, Book3e, Book3s/32), also handle the _PAGE_COHERENT flag with corresponds to the M bit of the WIMG flags.

---
 arch/powerpc/mm/ptdump/shared.c | 5 +++++
 1 file changed, 5 insertions(+)
arch/powerpc/mm/ptdump/shared.c +5 -0
index dab5d8028a9b..634b83aa3487 100644
@@ -40,6 +40,11 @@ static const struct flag_info flag_array[] = {
 		.val	= _PAGE_NO_CACHE,
 		.set	= "i",
 		.clear	= " ",
+	}, {
+		.mask	= _PAGE_COHERENT,
+		.val	= _PAGE_COHERENT,
+		.set	= "m",
+		.clear	= " ",
 	}, {
 		.mask	= _PAGE_GUARDED,
 		.val	= _PAGE_GUARDED,
Signature · 1 line
2.25.0
#13 lore raw

PATCH v4 10/45 powerpc/ptdump: Display size of BATs

In reply to Christophe Leroy

Display the size of areas mapped with BATs.

For that, the size display for pages is refactorised.

---
v2: Add missing include of linux/seq_file.h (Thanks to kbuild test robot)

---
 arch/powerpc/mm/ptdump/bats.c   |  4 ++++
 arch/powerpc/mm/ptdump/ptdump.c | 23 ++++++++++++++---------
 arch/powerpc/mm/ptdump/ptdump.h |  3 +++
 3 files changed, 21 insertions(+), 9 deletions(-)
arch/powerpc/mm/ptdump/bats.c +4 -0
index d3a5d6b318d1..d6c660f63d71 100644
@@ -10,6 +10,8 @@
 #include <asm/pgtable.h>
 #include <asm/cpu_has_feature.h>
 
+#include "ptdump.h"
+
 static char *pp_601(int k, int pp)
 {
 	if (pp == 0)
@@ -42,6 +44,7 @@ static void bat_show_601(struct seq_file *m, int idx, u32 lower, u32 upper)
 #else
 	seq_printf(m, "0x%08x ", pbn);
 #endif
+	pt_dump_size(m, size);
 
 	seq_printf(m, "Kernel %s User %s", pp_601(k & 2, pp), pp_601(k & 1, pp));
 
@@ -88,6 +91,7 @@ static void bat_show_603(struct seq_file *m, int idx, u32 lower, u32 upper, bool
 #else
 	seq_printf(m, "0x%08x ", brpn);
 #endif
+	pt_dump_size(m, size);
 
 	if (k == 1)
 		seq_puts(m, "User ");
arch/powerpc/mm/ptdump/ptdump.c +14 -9
index d92bb8ea229c..1f97668853e3 100644
@@ -112,6 +112,19 @@ static struct addr_marker address_markers[] = {
 		seq_putc(m, c);		\
 })
 
+void pt_dump_size(struct seq_file *m, unsigned long size)
+{
+	static const char units[] = "KMGTPE";
+	const char *unit = units;
+
+	/* Work out what appropriate unit to use */
+	while (!(size & 1023) && unit[1]) {
+		size >>= 10;
+		unit++;
+	}
+	pt_dump_seq_printf(m, "%9lu%c ", size, *unit);
+}
+
 static void dump_flag_info(struct pg_state *st, const struct flag_info
 		*flag, u64 pte, int num)
 {
@@ -146,8 +159,6 @@ static void dump_flag_info(struct pg_state *st, const struct flag_info
 
 static void dump_addr(struct pg_state *st, unsigned long addr)
 {
-	static const char units[] = "KMGTPE";
-	const char *unit = units;
 	unsigned long delta;
 
 #ifdef CONFIG_PPC64
@@ -164,13 +175,7 @@ static void dump_addr(struct pg_state *st, unsigned long addr)
 		pt_dump_seq_printf(st->seq, " " REG " ", st->start_pa);
 		delta = (addr - st->start_address) >> 10;
 	}
-	/* Work out what appropriate unit to use */
-	while (!(delta & 1023) && unit[1]) {
-		delta >>= 10;
-		unit++;
-	}
-	pt_dump_seq_printf(st->seq, "%9lu%c", delta, *unit);
-
+	pt_dump_size(st->seq, delta);
 }
 
 static void note_prot_wx(struct pg_state *st, unsigned long addr)
arch/powerpc/mm/ptdump/ptdump.h +3 -0
index 5d513636de73..154efae96ae0 100644
@@ -1,5 +1,6 @@
 /* SPDX-License-Identifier: GPL-2.0 */
 #include <linux/types.h>
+#include <linux/seq_file.h>
 
 struct flag_info {
 	u64		mask;
@@ -17,3 +18,5 @@ struct pgtable_level {
 };
 
 extern struct pgtable_level pg_level[5];
+
+void pt_dump_size(struct seq_file *m, unsigned long delta);
Signature · 1 line
2.25.0
#14 lore raw

PATCH v4 11/45 powerpc/ptdump: Standardise display of BAT flags

In reply to Christophe Leroy

Display BAT flags the same way as page flags: rwx and wimg

---
 arch/powerpc/mm/ptdump/bats.c | 37 ++++++++++++++---------------------
 1 file changed, 15 insertions(+), 22 deletions(-)
arch/powerpc/mm/ptdump/bats.c +15 -22
index d6c660f63d71..cebb58c7e289 100644
@@ -15,12 +15,12 @@
 static char *pp_601(int k, int pp)
 {
 	if (pp == 0)
-		return k ? "NA" : "RWX";
+		return k ? "   " : "rwx";
 	if (pp == 1)
-		return k ? "ROX" : "RWX";
+		return k ? "r x" : "rwx";
 	if (pp == 2)
-		return k ? "RWX" : "RWX";
-	return k ? "ROX" : "ROX";
+		return "rwx";
+	return "r x";
 }
 
 static void bat_show_601(struct seq_file *m, int idx, u32 lower, u32 upper)
@@ -48,12 +48,9 @@ static void bat_show_601(struct seq_file *m, int idx, u32 lower, u32 upper)
 
 	seq_printf(m, "Kernel %s User %s", pp_601(k & 2, pp), pp_601(k & 1, pp));
 
-	if (lower & _PAGE_WRITETHRU)
-		seq_puts(m, "write through ");
-	if (lower & _PAGE_NO_CACHE)
-		seq_puts(m, "no cache ");
-	if (lower & _PAGE_COHERENT)
-		seq_puts(m, "coherent ");
+	seq_puts(m, lower & _PAGE_WRITETHRU ? "w " : "  ");
+	seq_puts(m, lower & _PAGE_NO_CACHE ? "i " : "  ");
+	seq_puts(m, lower & _PAGE_COHERENT ? "m " : "  ");
 	seq_puts(m, "\n");
 }
 
@@ -101,20 +98,16 @@ static void bat_show_603(struct seq_file *m, int idx, u32 lower, u32 upper, bool
 		seq_puts(m, "Kernel/User ");
 
 	if (lower & BPP_RX)
-		seq_puts(m, is_d ? "RO " : "EXEC ");
+		seq_puts(m, is_d ? "r   " : "  x ");
 	else if (lower & BPP_RW)
-		seq_puts(m, is_d ? "RW " : "EXEC ");
+		seq_puts(m, is_d ? "rw  " : "  x ");
 	else
-		seq_puts(m, is_d ? "NA " : "NX   ");
-
-	if (lower & _PAGE_WRITETHRU)
-		seq_puts(m, "write through ");
-	if (lower & _PAGE_NO_CACHE)
-		seq_puts(m, "no cache ");
-	if (lower & _PAGE_COHERENT)
-		seq_puts(m, "coherent ");
-	if (lower & _PAGE_GUARDED)
-		seq_puts(m, "guarded ");
+		seq_puts(m, is_d ? "    " : "    ");
+
+	seq_puts(m, lower & _PAGE_WRITETHRU ? "w " : "  ");
+	seq_puts(m, lower & _PAGE_NO_CACHE ? "i " : "  ");
+	seq_puts(m, lower & _PAGE_COHERENT ? "m " : "  ");
+	seq_puts(m, lower & _PAGE_GUARDED ? "g " : "  ");
 	seq_puts(m, "\n");
 }
 
Signature · 1 line
2.25.0
#15 lore raw

PATCH v4 12/45 powerpc/ptdump: Properly handle non standard page size

In reply to Christophe Leroy

In order to properly display information regardless of the page size, it is necessary to take into account real page size.

Fixes cabe8138b23c ("powerpc: dump as a single line areas mapping a single physical page.")

---
v3: Fixed sizes which were shifted one level (went unoticed on PPC32 as PMD and PUD level don't exist)

---
 arch/powerpc/mm/ptdump/ptdump.c | 21 ++++++++++++---------
 1 file changed, 12 insertions(+), 9 deletions(-)
arch/powerpc/mm/ptdump/ptdump.c +12 -9
index 1f97668853e3..98d82dcf6f0b 100644
@@ -60,6 +60,7 @@ struct pg_state {
 	unsigned long start_address;
 	unsigned long start_pa;
 	unsigned long last_pa;
+	unsigned long page_size;
 	unsigned int level;
 	u64 current_flags;
 	bool check_wx;
@@ -168,9 +169,9 @@ static void dump_addr(struct pg_state *st, unsigned long addr)
 #endif
 
 	pt_dump_seq_printf(st->seq, REG "-" REG " ", st->start_address, addr - 1);
-	if (st->start_pa == st->last_pa && st->start_address + PAGE_SIZE != addr) {
+	if (st->start_pa == st->last_pa && st->start_address + st->page_size != addr) {
 		pt_dump_seq_printf(st->seq, "[" REG "]", st->start_pa);
-		delta = PAGE_SIZE >> 10;
+		delta = st->page_size >> 10;
 	} else {
 		pt_dump_seq_printf(st->seq, " " REG " ", st->start_pa);
 		delta = (addr - st->start_address) >> 10;
@@ -195,7 +196,7 @@ static void note_prot_wx(struct pg_state *st, unsigned long addr)
 }
 
 static void note_page(struct pg_state *st, unsigned long addr,
-	       unsigned int level, u64 val)
+	       unsigned int level, u64 val, unsigned long page_size)
 {
 	u64 flag = val & pg_level[level].mask;
 	u64 pa = val & PTE_RPN_MASK;
@@ -207,6 +208,7 @@ static void note_page(struct pg_state *st, unsigned long addr,
 		st->start_address = addr;
 		st->start_pa = pa;
 		st->last_pa = pa;
+		st->page_size = page_size;
 		pt_dump_seq_printf(st->seq, "---[ %s ]---\n", st->marker->name);
 	/*
 	 * Dump the section of virtual memory when:
@@ -218,7 +220,7 @@ static void note_page(struct pg_state *st, unsigned long addr,
 	 */
 	} else if (flag != st->current_flags || level != st->level ||
 		   addr >= st->marker[1].start_address ||
-		   (pa != st->last_pa + PAGE_SIZE &&
+		   (pa != st->last_pa + st->page_size &&
 		    (pa != st->start_pa || st->start_pa != st->last_pa))) {
 
 		/* Check the PTE flags */
@@ -246,6 +248,7 @@ static void note_page(struct pg_state *st, unsigned long addr,
 		st->start_address = addr;
 		st->start_pa = pa;
 		st->last_pa = pa;
+		st->page_size = page_size;
 		st->current_flags = flag;
 		st->level = level;
 	} else {
@@ -261,7 +264,7 @@ static void walk_pte(struct pg_state *st, pmd_t *pmd, unsigned long start)
 
 	for (i = 0; i < PTRS_PER_PTE; i++, pte++) {
 		addr = start + i * PAGE_SIZE;
-		note_page(st, addr, 4, pte_val(*pte));
+		note_page(st, addr, 4, pte_val(*pte), PAGE_SIZE);
 
 	}
 }
@@ -278,7 +281,7 @@ static void walk_pmd(struct pg_state *st, pud_t *pud, unsigned long start)
 			/* pmd exists */
 			walk_pte(st, pmd, addr);
 		else
-			note_page(st, addr, 3, pmd_val(*pmd));
+			note_page(st, addr, 3, pmd_val(*pmd), PMD_SIZE);
 	}
 }
 
@@ -294,7 +297,7 @@ static void walk_pud(struct pg_state *st, pgd_t *pgd, unsigned long start)
 			/* pud exists */
 			walk_pmd(st, pud, addr);
 		else
-			note_page(st, addr, 2, pud_val(*pud));
+			note_page(st, addr, 2, pud_val(*pud), PUD_SIZE);
 	}
 }
 
@@ -313,7 +316,7 @@ static void walk_pagetables(struct pg_state *st)
 			/* pgd exists */
 			walk_pud(st, pgd, addr);
 		else
-			note_page(st, addr, 1, pgd_val(*pgd));
+			note_page(st, addr, 1, pgd_val(*pgd), PGDIR_SIZE);
 	}
 }
 
@@ -368,7 +371,7 @@ static int ptdump_show(struct seq_file *m, void *v)
 
 	/* Traverse kernel page tables */
 	walk_pagetables(&st);
-	note_page(&st, 0, 0, 0);
+	note_page(&st, 0, 0, 0, 0);
 	return 0;
 }
 
Signature · 1 line
2.25.0
#16 lore raw

PATCH v4 13/45 powerpc/ptdump: Handle hugepd at PGD level

In reply to Christophe Leroy

The 8xx is about to map kernel linear space and IMMR using huge pages.

In order to display those pages properly, ptdump needs to handle hugepd tables at PGD level.

For the time being do it only at PGD level. Further patches may add handling of hugepd tables at lower level for other platforms when needed in the future.

---
v3: notepage() now takes page size instead of page shift

---
 arch/powerpc/mm/ptdump/ptdump.c | 29 ++++++++++++++++++++++++++---
 1 file changed, 26 insertions(+), 3 deletions(-)
arch/powerpc/mm/ptdump/ptdump.c +26 -3
index 98d82dcf6f0b..5fc880e30175 100644
@@ -23,6 +23,7 @@
 #include <linux/const.h>
 #include <asm/page.h>
 #include <asm/pgalloc.h>
+#include <asm/hugetlb.h>
 
 #include <mm/mmu_decl.h>
 
@@ -269,6 +270,26 @@ static void walk_pte(struct pg_state *st, pmd_t *pmd, unsigned long start)
 	}
 }
 
+static void walk_hugepd(struct pg_state *st, hugepd_t *phpd, unsigned long start,
+			int pdshift, int level)
+{
+#ifdef CONFIG_ARCH_HAS_HUGEPD
+	unsigned int i;
+	int shift = hugepd_shift(*phpd);
+	int ptrs_per_hpd = pdshift - shift > 0 ? 1 << (pdshift - shift) : 1;
+
+	if (start & ((1 << shift) - 1))
+		return;
+
+	for (i = 0; i < ptrs_per_hpd; i++) {
+		unsigned long addr = start + (i << shift);
+		pte_t *pte = hugepte_offset(*phpd, addr, pdshift);
+
+		note_page(st, addr, level + 1, pte_val(*pte), 1 << shift);
+	}
+#endif
+}
+
 static void walk_pmd(struct pg_state *st, pud_t *pud, unsigned long start)
 {
 	pmd_t *pmd = pmd_offset(pud, 0);
@@ -312,11 +333,13 @@ static void walk_pagetables(struct pg_state *st)
 	 * the hash pagetable.
 	 */
 	for (i = pgd_index(addr); i < PTRS_PER_PGD; i++, pgd++, addr += PGDIR_SIZE) {
-		if (!pgd_none(*pgd) && !pgd_is_leaf(*pgd))
+		if (pgd_none(*pgd) || pgd_is_leaf(*pgd))
+			note_page(st, addr, 1, pgd_val(*pgd), PGDIR_SIZE);
+		else if (is_hugepd(__hugepd(pgd_val(*pgd))))
+			walk_hugepd(st, (hugepd_t *)pgd, addr, PGDIR_SHIFT, 1);
+		else
 			/* pgd exists */
 			walk_pud(st, pgd, addr);
-		else
-			note_page(st, addr, 1, pgd_val(*pgd), PGDIR_SIZE);
 	}
 }
 
Signature · 1 line
2.25.0
#17 lore raw

PATCH v4 14/45 powerpc/32s: Don't warn when mapping RO data ROX.

In reply to Christophe Leroy

Mapping RO data as ROX is not an issue since that data cannot be modified to introduce an exploit.

PPC64 accepts to have RO data mapped ROX, as a trade off between kernel size and strictness of protection.

On PPC32, kernel size is even more critical as amount of memory is usually small.

Depending on the number of available IBATs, the last IBATs might overflow the end of text. Only warn if it crosses the end of RO data.

---
 arch/powerpc/mm/book3s32/mmu.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
arch/powerpc/mm/book3s32/mmu.c +4 -2
index 39ba53ca5bb5..a9b2cbc74797 100644
@@ -187,6 +187,7 @@ void mmu_mark_initmem_nx(void)
 	int i;
 	unsigned long base = (unsigned long)_stext - PAGE_OFFSET;
 	unsigned long top = (unsigned long)_etext - PAGE_OFFSET;
+	unsigned long border = (unsigned long)__init_begin - PAGE_OFFSET;
 	unsigned long size;
 
 	if (IS_ENABLED(CONFIG_PPC_BOOK3S_601))
@@ -201,9 +202,10 @@ void mmu_mark_initmem_nx(void)
 		size = block_size(base, top);
 		size = max(size, 128UL << 10);
 		if ((top - base) > size) {
-			if (strict_kernel_rwx_enabled())
-				pr_warn("Kernel _etext not properly aligned\n");
 			size <<= 1;
+			if (strict_kernel_rwx_enabled() && base + size > border)
+				pr_warn("Some RW data is getting mapped X. "
+					"Adjust CONFIG_DATA_SHIFT to avoid that.\n");
 		}
 		setibat(i++, PAGE_OFFSET + base, base, size, PAGE_KERNEL_TEXT);
 		base += size;
Signature · 1 line
2.25.0
#18 lore raw

Re: [PATCH v4 14/45] powerpc/32s: Don't warn when mapping RO data ROX.

Quoted 2 lines · Christophe Leroy

Mapping RO data as ROX is not an issue since that data cannot be modified to introduce an exploit.

Being pedantic: it is still an issue, in that it means there's more targets for a code-reuse attack.

But given the entire kernel text is also available for code-reuse attacks, the RO data is unlikely to contain any useful sequences that aren't also in the kernel text.

Quoted 5 lines

PPC64 accepts to have RO data mapped ROX, as a trade off between kernel size and strictness of protection.

On PPC32, kernel size is even more critical as amount of memory is usually small.

Yep, I think it's a reasonable trade off to make.

cheers

Quoted 36 lines

Depending on the number of available IBATs, the last IBATs might overflow the end of text. Only warn if it crosses the end of RO data.

---
 arch/powerpc/mm/book3s32/mmu.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
arch/powerpc/mm/book3s32/mmu.c +4 -2
index 39ba53ca5bb5..a9b2cbc74797 100644
@@ -187,6 +187,7 @@ void mmu_mark_initmem_nx(void)
 	int i;
 	unsigned long base = (unsigned long)_stext - PAGE_OFFSET;
 	unsigned long top = (unsigned long)_etext - PAGE_OFFSET;
+	unsigned long border = (unsigned long)__init_begin - PAGE_OFFSET;
 	unsigned long size;
 
 	if (IS_ENABLED(CONFIG_PPC_BOOK3S_601))
@@ -201,9 +202,10 @@ void mmu_mark_initmem_nx(void)
 		size = block_size(base, top);
 		size = max(size, 128UL << 10);
 		if ((top - base) > size) {
-			if (strict_kernel_rwx_enabled())
-				pr_warn("Kernel _etext not properly aligned\n");
 			size <<= 1;
+			if (strict_kernel_rwx_enabled() && base + size > border)
+				pr_warn("Some RW data is getting mapped X. "
+					"Adjust CONFIG_DATA_SHIFT to avoid that.\n");
 		}
 		setibat(i++, PAGE_OFFSET + base, base, size, PAGE_KERNEL_TEXT);
 		base += size;
Signature · 1 line
2.25.0
#19 lore raw

PATCH v4 15/45 powerpc/mm: Allocate static page tables for fixmap

In reply to Christophe Leroy

Allocate static page tables for the fixmap area. This allows setting mappings through page tables before memblock is ready. That's needed to use early_ioremap() early and to use standard page mappings with fixmap.

---
 arch/powerpc/include/asm/fixmap.h |  4 ++++
 arch/powerpc/kernel/setup_32.c    |  2 +-
 arch/powerpc/mm/pgtable_32.c      | 16 ++++++++++++++++
 3 files changed, 21 insertions(+), 1 deletion(-)
arch/powerpc/include/asm/fixmap.h +4 -0
index 2ef155a3c821..ccbe2e83c950 100644
@@ -86,6 +86,10 @@ enum fixed_addresses {
 #define __FIXADDR_SIZE	(__end_of_fixed_addresses << PAGE_SHIFT)
 #define FIXADDR_START		(FIXADDR_TOP - __FIXADDR_SIZE)
 
+#define FIXMAP_ALIGNED_SIZE	(ALIGN(FIXADDR_TOP, PGDIR_SIZE) - \
+				 ALIGN_DOWN(FIXADDR_START, PGDIR_SIZE))
+#define FIXMAP_PTE_SIZE	(FIXMAP_ALIGNED_SIZE / PGDIR_SIZE * PTE_TABLE_SIZE)
+
 #define FIXMAP_PAGE_NOCACHE PAGE_KERNEL_NCG
 #define FIXMAP_PAGE_IO	PAGE_KERNEL_NCG
 
arch/powerpc/kernel/setup_32.c +1 -1
index 15f0a7c84944..d642e42eabb1 100644
@@ -80,7 +80,7 @@ notrace void __init machine_init(u64 dt_ptr)
 	/* Configure static keys first, now that we're relocated. */
 	setup_feature_keys();
 
-	early_ioremap_setup();
+	early_ioremap_init();
 
 	/* Enable early debugging if any specified (see udbg.h) */
 	udbg_early_init();
arch/powerpc/mm/pgtable_32.c +16 -0
index f62de06e3d07..9934659cb871 100644
@@ -29,11 +29,27 @@
 #include <asm/fixmap.h>
 #include <asm/setup.h>
 #include <asm/sections.h>
+#include <asm/early_ioremap.h>
 
 #include <mm/mmu_decl.h>
 
 extern char etext[], _stext[], _sinittext[], _einittext[];
 
+static u8 early_fixmap_pagetable[FIXMAP_PTE_SIZE] __page_aligned_data;
+
+notrace void __init early_ioremap_init(void)
+{
+	unsigned long addr = ALIGN_DOWN(FIXADDR_START, PGDIR_SIZE);
+	pte_t *ptep = (pte_t *)early_fixmap_pagetable;
+	pmd_t *pmdp = pmd_ptr_k(addr);
+
+	for (; (s32)(FIXADDR_TOP - addr) > 0;
+	     addr += PGDIR_SIZE, ptep += PTRS_PER_PTE, pmdp++)
+		pmd_populate_kernel(&init_mm, pmdp, ptep);
+
+	early_ioremap_setup();
+}
+
 static void __init *early_alloc_pgtable(unsigned long size)
 {
 	void *ptr = memblock_alloc(size, size);
Signature · 1 line
2.25.0
#20 lore raw

PATCH v4 16/45 powerpc/mm: Fix conditions to perform MMU specific management by blocks on PPC32.

In reply to Christophe Leroy

Setting init mem to NX shall depend on sinittext being mapped by block, not on stext being mapped by block.

Setting text and rodata to RO shall depend on stext being mapped by block, not on sinittext being mapped by block.

Fixes 63b2bc619565 ("powerpc/mm/32s: Use BATs for STRICT_KERNEL_RWX")
---
 arch/powerpc/mm/pgtable_32.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/powerpc/mm/pgtable_32.c +2 -2
index 9934659cb871..bd0cb6e3573e 100644
@@ -185,7 +185,7 @@ void mark_initmem_nx(void)
 	unsigned long numpages = PFN_UP((unsigned long)_einittext) -
 				 PFN_DOWN((unsigned long)_sinittext);
 
-	if (v_block_mapped((unsigned long)_stext + 1))
+	if (v_block_mapped((unsigned long)_sinittext))
 		mmu_mark_initmem_nx();
 	else
 		change_page_attr(page, numpages, PAGE_KERNEL);
@@ -197,7 +197,7 @@ void mark_rodata_ro(void)
 	struct page *page;
 	unsigned long numpages;
 
-	if (v_block_mapped((unsigned long)_sinittext)) {
+	if (v_block_mapped((unsigned long)_stext + 1)) {
 		mmu_mark_rodata_ro();
 		ptdump_check_wx();
 		return;
Signature · 1 line
2.25.0
#21 lore raw

PATCH v4 17/45 powerpc/mm: PTE_ATOMIC_UPDATES is only for 40x

In reply to Christophe Leroy

Only 40x still uses PTE_ATOMIC_UPDATES.
40x cannot not select CONFIG_PTE64_BIT.

Drop handling of PTE_ATOMIC_UPDATES:
- In nohash/64
- In nohash/32 for CONFIG_PTE_64BIT

Keep PTE_ATOMIC_UPDATES only for nohash/32 for !CONFIG_PTE_64BIT

---
 arch/powerpc/include/asm/nohash/32/pgtable.h | 17 ------------
 arch/powerpc/include/asm/nohash/64/pgtable.h | 28 +-------------------
 2 files changed, 1 insertion(+), 44 deletions(-)
arch/powerpc/include/asm/nohash/32/pgtable.h +0 -17
index 4315d40906a0..7e908a176e9e 100644
@@ -262,25 +262,8 @@ static inline unsigned long long pte_update(pte_t *p,
 					    unsigned long clr,
 					    unsigned long set)
 {
-#ifdef PTE_ATOMIC_UPDATES
-	unsigned long long old;
-	unsigned long tmp;
-
-	__asm__ __volatile__("\
-1:	lwarx	%L0,0,%4\n\
-	lwzx	%0,0,%3\n\
-	andc	%1,%L0,%5\n\
-	or	%1,%1,%6\n"
-	PPC405_ERR77(0,%3)
-"	stwcx.	%1,0,%4\n\
-	bne-	1b"
-	: "=&r" (old), "=&r" (tmp), "=m" (*p)
-	: "r" (p), "r" ((unsigned long)(p) + 4), "r" (clr), "r" (set), "m" (*p)
-	: "cc" );
-#else /* PTE_ATOMIC_UPDATES */
 	unsigned long long old = pte_val(*p);
 	*p = __pte((old & ~(unsigned long long)clr) | set);
-#endif /* !PTE_ATOMIC_UPDATES */
 
 #ifdef CONFIG_44x
 	if ((old & _PAGE_USER) && (old & _PAGE_EXEC))
arch/powerpc/include/asm/nohash/64/pgtable.h +1 -27
index 9a33b8bd842d..9c703b140d64 100644
@@ -211,22 +211,9 @@ static inline unsigned long pte_update(struct mm_struct *mm,
 				       unsigned long set,
 				       int huge)
 {
-#ifdef PTE_ATOMIC_UPDATES
-	unsigned long old, tmp;
-
-	__asm__ __volatile__(
-	"1:	ldarx	%0,0,%3		# pte_update\n\
-	andc	%1,%0,%4 \n\
-	or	%1,%1,%6\n\
-	stdcx.	%1,0,%3 \n\
-	bne-	1b"
-	: "=&r" (old), "=&r" (tmp), "=m" (*ptep)
-	: "r" (ptep), "r" (clr), "m" (*ptep), "r" (set)
-	: "cc" );
-#else
 	unsigned long old = pte_val(*ptep);
 	*ptep = __pte((old & ~clr) | set);
-#endif
+
 	/* huge pages use the old page table lock */
 	if (!huge)
 		assert_pte_locked(mm, addr);
@@ -310,21 +297,8 @@ static inline void __ptep_set_access_flags(struct vm_area_struct *vma,
 	unsigned long bits = pte_val(entry) &
 		(_PAGE_DIRTY | _PAGE_ACCESSED | _PAGE_RW | _PAGE_EXEC);
 
-#ifdef PTE_ATOMIC_UPDATES
-	unsigned long old, tmp;
-
-	__asm__ __volatile__(
-	"1:	ldarx	%0,0,%4\n\
-		or	%0,%3,%0\n\
-		stdcx.	%0,0,%4\n\
-		bne-	1b"
-	:"=&r" (old), "=&r" (tmp), "=m" (*ptep)
-	:"r" (bits), "r" (ptep), "m" (*ptep)
-	:"cc");
-#else
 	unsigned long old = pte_val(*ptep);
 	*ptep = __pte(old | bits);
-#endif
 
 	flush_tlb_page(vma, address);
 }
Signature · 1 line
2.25.0
#22 lore raw

PATCH v4 18/45 powerpc/mm: Refactor pte_update() on nohash/32

In reply to Christophe Leroy

When CONFIG_PTE_64BIT is set, pte_update() operates on 'unsigned long long'
When CONFIG_PTE_64BIT is not set, pte_update() operates on 'unsigned long'

In asm/page.h, we have pte_basic_t which is 'unsigned long long' when CONFIG_PTE_64BIT is set and 'unsigned long' otherwise.

Refactor pte_update() using pte_basic_t.

---
 arch/powerpc/include/asm/nohash/32/pgtable.h | 26 +++-----------------
 1 file changed, 4 insertions(+), 22 deletions(-)
arch/powerpc/include/asm/nohash/32/pgtable.h +4 -22
index 7e908a176e9e..db17f50d6ac3 100644
@@ -222,12 +222,9 @@ static inline void pmd_clear(pmd_t *pmdp)
  * to properly flush the virtually tagged instruction cache of
  * those implementations.
  */
-#ifndef CONFIG_PTE_64BIT
-static inline unsigned long pte_update(pte_t *p,
-				       unsigned long clr,
-				       unsigned long set)
+static inline pte_basic_t pte_update(pte_t *p, unsigned long clr, unsigned long set)
 {
-#ifdef PTE_ATOMIC_UPDATES
+#if defined(PTE_ATOMIC_UPDATES) && !defined(CONFIG_PTE_64BIT)
 	unsigned long old, tmp;
 
 	__asm__ __volatile__("\
@@ -241,8 +238,8 @@ static inline unsigned long pte_update(pte_t *p,
 	: "r" (p), "r" (clr), "r" (set), "m" (*p)
 	: "cc" );
 #else /* PTE_ATOMIC_UPDATES */
-	unsigned long old = pte_val(*p);
-	unsigned long new = (old & ~clr) | set;
+	pte_basic_t old = pte_val(*p);
+	pte_basic_t new = (old & ~(pte_basic_t)clr) | set;
 
 #if defined(CONFIG_PPC_8xx) && defined(CONFIG_PPC_16K_PAGES)
 	p->pte = p->pte1 = p->pte2 = p->pte3 = new;
@@ -257,21 +254,6 @@ static inline unsigned long pte_update(pte_t *p,
 #endif
 	return old;
 }
-#else /* CONFIG_PTE_64BIT */
-static inline unsigned long long pte_update(pte_t *p,
-					    unsigned long clr,
-					    unsigned long set)
-{
-	unsigned long long old = pte_val(*p);
-	*p = __pte((old & ~(unsigned long long)clr) | set);
-
-#ifdef CONFIG_44x
-	if ((old & _PAGE_USER) && (old & _PAGE_EXEC))
-		icache_44x_need_flush = 1;
-#endif
-	return old;
-}
-#endif /* CONFIG_PTE_64BIT */
 
 #define __HAVE_ARCH_PTEP_TEST_AND_CLEAR_YOUNG
 static inline int __ptep_test_and_clear_young(unsigned int context, unsigned long addr, pte_t *ptep)
Signature · 1 line
2.25.0
#23 lore raw

PATCH v4 19/45 powerpc/mm: Refactor pte_update() on book3s/32

In reply to Christophe Leroy

When CONFIG_PTE_64BIT is set, pte_update() operates on 'unsigned long long'
When CONFIG_PTE_64BIT is not set, pte_update() operates on 'unsigned long'

In asm/page.h, we have pte_basic_t which is 'unsigned long long' when CONFIG_PTE_64BIT is set and 'unsigned long' otherwise.

Refactor pte_update() using pte_basic_t.

While we are at it, drop the comment on 44x which is not applicable to book3s version of pte_update().

---
 arch/powerpc/include/asm/book3s/32/pgtable.h | 58 +++++++-------------
 1 file changed, 20 insertions(+), 38 deletions(-)
arch/powerpc/include/asm/book3s/32/pgtable.h +20 -38
index 0d4bccb4b9f2..d2fc324cdf07 100644
@@ -253,53 +253,35 @@ extern void flush_hash_entry(struct mm_struct *mm, pte_t *ptep,
  * and the PTE may be either 32 or 64 bit wide. In the later case,
  * when using atomic updates, only the low part of the PTE is
  * accessed atomically.
- *
- * In addition, on 44x, we also maintain a global flag indicating
- * that an executable user mapping was modified, which is needed
- * to properly flush the virtually tagged instruction cache of
- * those implementations.
  */
-#ifndef CONFIG_PTE_64BIT
-static inline unsigned long pte_update(pte_t *p,
-				       unsigned long clr,
-				       unsigned long set)
+static inline pte_basic_t pte_update(pte_t *p, unsigned long clr, unsigned long set)
 {
-	unsigned long old, tmp;
-
-	__asm__ __volatile__("\
-1:	lwarx	%0,0,%3\n\
-	andc	%1,%0,%4\n\
-	or	%1,%1,%5\n"
-"	stwcx.	%1,0,%3\n\
-	bne-	1b"
-	: "=&r" (old), "=&r" (tmp), "=m" (*p)
-	: "r" (p), "r" (clr), "r" (set), "m" (*p)
-	: "cc" );
-
-	return old;
-}
-#else /* CONFIG_PTE_64BIT */
-static inline unsigned long long pte_update(pte_t *p,
-					    unsigned long clr,
-					    unsigned long set)
-{
-	unsigned long long old;
+	pte_basic_t old;
 	unsigned long tmp;
 
-	__asm__ __volatile__("\
-1:	lwarx	%L0,0,%4\n\
-	lwzx	%0,0,%3\n\
-	andc	%1,%L0,%5\n\
-	or	%1,%1,%6\n"
-"	stwcx.	%1,0,%4\n\
-	bne-	1b"
+	__asm__ __volatile__(
+#ifndef CONFIG_PTE_64BIT
+"1:	lwarx	%0, 0, %3\n"
+"	andc	%1, %0, %4\n"
+#else
+"1:	lwarx	%L0, 0, %3\n"
+"	lwz	%0, -4(%3)\n"
+"	andc	%1, %L0, %4\n"
+#endif
+"	or	%1, %1, %5\n"
+"	stwcx.	%1, 0, %3\n"
+"	bne-	1b"
 	: "=&r" (old), "=&r" (tmp), "=m" (*p)
-	: "r" (p), "r" ((unsigned long)(p) + 4), "r" (clr), "r" (set), "m" (*p)
+#ifndef CONFIG_PTE_64BIT
+	: "r" (p),
+#else
+	: "b" ((unsigned long)(p) + 4),
+#endif
+	  "r" (clr), "r" (set), "m" (*p)
 	: "cc" );
 
 	return old;
 }
-#endif /* CONFIG_PTE_64BIT */
 
 /*
  * 2.6 calls this without flushing the TLB entry; this is wrong
Signature · 1 line
2.25.0
#24 lore raw

PATCH v4 20/45 powerpc/mm: Standardise __ptep_test_and_clear_young() params between PPC32 and PPC64

In reply to Christophe Leroy

On PPC32, __ptep_test_and_clear_young() takes the mm->context.id

In preparation of standardising pte_update() params between PPC32 and PPC64, __ptep_test_and_clear_young() need mm instead of mm->context.id

Replace context param by mm.

---
 arch/powerpc/include/asm/book3s/32/pgtable.h | 7 ++++---
 arch/powerpc/include/asm/nohash/32/pgtable.h | 5 +++--
 2 files changed, 7 insertions(+), 5 deletions(-)
arch/powerpc/include/asm/book3s/32/pgtable.h +4 -3
index d2fc324cdf07..25c59511fcab 100644
@@ -288,18 +288,19 @@ static inline pte_basic_t pte_update(pte_t *p, unsigned long clr, unsigned long
  * for our hash-based implementation, we fix that up here.
  */
 #define __HAVE_ARCH_PTEP_TEST_AND_CLEAR_YOUNG
-static inline int __ptep_test_and_clear_young(unsigned int context, unsigned long addr, pte_t *ptep)
+static inline int __ptep_test_and_clear_young(struct mm_struct *mm,
+					      unsigned long addr, pte_t *ptep)
 {
 	unsigned long old;
 	old = pte_update(ptep, _PAGE_ACCESSED, 0);
 	if (old & _PAGE_HASHPTE) {
 		unsigned long ptephys = __pa(ptep) & PAGE_MASK;
-		flush_hash_pages(context, addr, ptephys, 1);
+		flush_hash_pages(mm->context.id, addr, ptephys, 1);
 	}
 	return (old & _PAGE_ACCESSED) != 0;
 }
 #define ptep_test_and_clear_young(__vma, __addr, __ptep) \
-	__ptep_test_and_clear_young((__vma)->vm_mm->context.id, __addr, __ptep)
+	__ptep_test_and_clear_young((__vma)->vm_mm, __addr, __ptep)
 
 #define __HAVE_ARCH_PTEP_GET_AND_CLEAR
 static inline pte_t ptep_get_and_clear(struct mm_struct *mm, unsigned long addr,
arch/powerpc/include/asm/nohash/32/pgtable.h +3 -2
index db17f50d6ac3..e963e6880d7c 100644
@@ -256,14 +256,15 @@ static inline pte_basic_t pte_update(pte_t *p, unsigned long clr, unsigned long
 }
 
 #define __HAVE_ARCH_PTEP_TEST_AND_CLEAR_YOUNG
-static inline int __ptep_test_and_clear_young(unsigned int context, unsigned long addr, pte_t *ptep)
+static inline int __ptep_test_and_clear_young(struct mm_struct *mm,
+					      unsigned long addr, pte_t *ptep)
 {
 	unsigned long old;
 	old = pte_update(ptep, _PAGE_ACCESSED, 0);
 	return (old & _PAGE_ACCESSED) != 0;
 }
 #define ptep_test_and_clear_young(__vma, __addr, __ptep) \
-	__ptep_test_and_clear_young((__vma)->vm_mm->context.id, __addr, __ptep)
+	__ptep_test_and_clear_young((__vma)->vm_mm, __addr, __ptep)
 
 #define __HAVE_ARCH_PTEP_GET_AND_CLEAR
 static inline pte_t ptep_get_and_clear(struct mm_struct *mm, unsigned long addr,
Signature · 1 line
2.25.0
#25 lore raw

PATCH v4 21/45 powerpc/mm: Standardise pte_update() prototype between PPC32 and PPC64

In reply to Christophe Leroy

PPC64 takes 3 additional parameters compared to PPC32:
- mm
- address
- huge

These 3 parameters will be needed in order to perform different action depending on the page size on the 8xx.

Make pte_update() prototype identical for PPC32 and PPC64.

This allows dropping an #ifdef in huge_ptep_get_and_clear().

---
 arch/powerpc/include/asm/book3s/32/pgtable.h | 15 ++++++++-------
 arch/powerpc/include/asm/hugetlb.h           |  4 ----
 arch/powerpc/include/asm/nohash/32/pgtable.h | 13 +++++++------
 3 files changed, 15 insertions(+), 17 deletions(-)
arch/powerpc/include/asm/book3s/32/pgtable.h +8 -7
index 25c59511fcab..8a091d125f2d 100644
@@ -218,7 +218,7 @@ int map_kernel_page(unsigned long va, phys_addr_t pa, pgprot_t prot);
  */
 
 #define pte_clear(mm, addr, ptep) \
-	do { pte_update(ptep, ~_PAGE_HASHPTE, 0); } while (0)
+	do { pte_update(mm, addr, ptep, ~_PAGE_HASHPTE, 0, 0); } while (0)
 
 #define pmd_none(pmd)		(!pmd_val(pmd))
 #define	pmd_bad(pmd)		(pmd_val(pmd) & _PMD_BAD)
@@ -254,7 +254,8 @@ extern void flush_hash_entry(struct mm_struct *mm, pte_t *ptep,
  * when using atomic updates, only the low part of the PTE is
  * accessed atomically.
  */
-static inline pte_basic_t pte_update(pte_t *p, unsigned long clr, unsigned long set)
+static inline pte_basic_t pte_update(struct mm_struct *mm, unsigned long addr, pte_t *p,
+				     unsigned long clr, unsigned long set, int huge)
 {
 	pte_basic_t old;
 	unsigned long tmp;
@@ -292,7 +293,7 @@ static inline int __ptep_test_and_clear_young(struct mm_struct *mm,
 					      unsigned long addr, pte_t *ptep)
 {
 	unsigned long old;
-	old = pte_update(ptep, _PAGE_ACCESSED, 0);
+	old = pte_update(mm, addr, ptep, _PAGE_ACCESSED, 0, 0);
 	if (old & _PAGE_HASHPTE) {
 		unsigned long ptephys = __pa(ptep) & PAGE_MASK;
 		flush_hash_pages(mm->context.id, addr, ptephys, 1);
@@ -306,14 +307,14 @@ static inline int __ptep_test_and_clear_young(struct mm_struct *mm,
 static inline pte_t ptep_get_and_clear(struct mm_struct *mm, unsigned long addr,
 				       pte_t *ptep)
 {
-	return __pte(pte_update(ptep, ~_PAGE_HASHPTE, 0));
+	return __pte(pte_update(mm, addr, ptep, ~_PAGE_HASHPTE, 0, 0));
 }
 
 #define __HAVE_ARCH_PTEP_SET_WRPROTECT
 static inline void ptep_set_wrprotect(struct mm_struct *mm, unsigned long addr,
 				      pte_t *ptep)
 {
-	pte_update(ptep, _PAGE_RW, 0);
+	pte_update(mm, addr, ptep, _PAGE_RW, 0, 0);
 }
 
 static inline void __ptep_set_access_flags(struct vm_area_struct *vma,
@@ -324,7 +325,7 @@ static inline void __ptep_set_access_flags(struct vm_area_struct *vma,
 	unsigned long set = pte_val(entry) &
 		(_PAGE_DIRTY | _PAGE_ACCESSED | _PAGE_RW | _PAGE_EXEC);
 
-	pte_update(ptep, 0, set);
+	pte_update(vma->vm_mm, address, ptep, 0, set, 0);
 
 	flush_tlb_page(vma, address);
 }
@@ -522,7 +523,7 @@ static inline void __set_pte_at(struct mm_struct *mm, unsigned long addr,
 		*ptep = __pte((pte_val(*ptep) & _PAGE_HASHPTE)
 			      | (pte_val(pte) & ~_PAGE_HASHPTE));
 	else
-		pte_update(ptep, ~_PAGE_HASHPTE, pte_val(pte));
+		pte_update(mm, addr, ptep, ~_PAGE_HASHPTE, pte_val(pte), 0);
 
 #elif defined(CONFIG_PTE_64BIT)
 	/* Second case is 32-bit with 64-bit PTE.  In this case, we
arch/powerpc/include/asm/hugetlb.h +0 -4
index bd6504c28c2f..e4276af034e9 100644
@@ -40,11 +40,7 @@ void hugetlb_free_pgd_range(struct mmu_gather *tlb, unsigned long addr,
 static inline pte_t huge_ptep_get_and_clear(struct mm_struct *mm,
 					    unsigned long addr, pte_t *ptep)
 {
-#ifdef CONFIG_PPC64
 	return __pte(pte_update(mm, addr, ptep, ~0UL, 0, 1));
-#else
-	return __pte(pte_update(ptep, ~0UL, 0));
-#endif
 }
 
 #define __HAVE_ARCH_HUGE_PTEP_CLEAR_FLUSH
arch/powerpc/include/asm/nohash/32/pgtable.h +7 -6
index e963e6880d7c..474dd1db065f 100644
@@ -166,7 +166,7 @@ int map_kernel_page(unsigned long va, phys_addr_t pa, pgprot_t prot);
 #ifndef __ASSEMBLY__
 
 #define pte_clear(mm, addr, ptep) \
-	do { pte_update(ptep, ~0, 0); } while (0)
+	do { pte_update(mm, addr, ptep, ~0, 0, 0); } while (0)
 
 #ifndef pte_mkwrite
 static inline pte_t pte_mkwrite(pte_t pte)
@@ -222,7 +222,8 @@ static inline void pmd_clear(pmd_t *pmdp)
  * to properly flush the virtually tagged instruction cache of
  * those implementations.
  */
-static inline pte_basic_t pte_update(pte_t *p, unsigned long clr, unsigned long set)
+static inline pte_basic_t pte_update(struct mm_struct *mm, unsigned long addr, pte_t *p,
+				     unsigned long clr, unsigned long set, int huge)
 {
 #if defined(PTE_ATOMIC_UPDATES) && !defined(CONFIG_PTE_64BIT)
 	unsigned long old, tmp;
@@ -260,7 +261,7 @@ static inline int __ptep_test_and_clear_young(struct mm_struct *mm,
 					      unsigned long addr, pte_t *ptep)
 {
 	unsigned long old;
-	old = pte_update(ptep, _PAGE_ACCESSED, 0);
+	old = pte_update(mm, addr, ptep, _PAGE_ACCESSED, 0, 0);
 	return (old & _PAGE_ACCESSED) != 0;
 }
 #define ptep_test_and_clear_young(__vma, __addr, __ptep) \
@@ -270,7 +271,7 @@ static inline int __ptep_test_and_clear_young(struct mm_struct *mm,
 static inline pte_t ptep_get_and_clear(struct mm_struct *mm, unsigned long addr,
 				       pte_t *ptep)
 {
-	return __pte(pte_update(ptep, ~0, 0));
+	return __pte(pte_update(mm, addr, ptep, ~0, 0, 0));
 }
 
 #define __HAVE_ARCH_PTEP_SET_WRPROTECT
@@ -280,7 +281,7 @@ static inline void ptep_set_wrprotect(struct mm_struct *mm, unsigned long addr,
 	unsigned long clr = ~pte_val(pte_wrprotect(__pte(~0)));
 	unsigned long set = pte_val(pte_wrprotect(__pte(0)));
 
-	pte_update(ptep, clr, set);
+	pte_update(mm, addr, ptep, clr, set, 0);
 }
 
 static inline void __ptep_set_access_flags(struct vm_area_struct *vma,
@@ -293,7 +294,7 @@ static inline void __ptep_set_access_flags(struct vm_area_struct *vma,
 	unsigned long set = pte_val(entry) & pte_val(pte_set);
 	unsigned long clr = ~pte_val(entry) & ~pte_val(pte_clr);
 
-	pte_update(ptep, clr, set);
+	pte_update(vma->vm_mm, address, ptep, clr, set, 0);
 
 	flush_tlb_page(vma, address);
 }
Signature · 1 line
2.25.0
#26 lore raw

PATCH v4 22/45 powerpc/mm: Create a dedicated pte_update() for 8xx

In reply to Christophe Leroy

pte_update() is a bit special for the 8xx. At the time being, that's an #ifdef inside the nohash/32 pte_update().

As we are going to make it even more special in the coming patches, create a dedicated version for pte_update() for 8xx.

---
 arch/powerpc/include/asm/nohash/32/pgtable.h | 29 +++++++++++++++++---
 1 file changed, 25 insertions(+), 4 deletions(-)
arch/powerpc/include/asm/nohash/32/pgtable.h +25 -4
index 474dd1db065f..5fb3f6798e22 100644
@@ -221,7 +221,31 @@ static inline void pmd_clear(pmd_t *pmdp)
  * that an executable user mapping was modified, which is needed
  * to properly flush the virtually tagged instruction cache of
  * those implementations.
+ *
+ * On the 8xx, the page tables are a bit special. For 16k pages, we have
+ * 4 identical entries. For other page sizes, we have a single entry in the
+ * table.
  */
+#ifdef CONFIG_PPC_8xx
+static inline pte_basic_t pte_update(struct mm_struct *mm, unsigned long addr, pte_t *p,
+				     unsigned long clr, unsigned long set, int huge)
+{
+	pte_basic_t *entry = &p->pte;
+	pte_basic_t old = pte_val(*p);
+	pte_basic_t new = (old & ~(pte_basic_t)clr) | set;
+	int num, i;
+
+	if (!huge)
+		num = PAGE_SIZE / SZ_4K;
+	else
+		num = 1;
+
+	for (i = 0; i < num; i++, entry++)
+		*entry = new;
+
+	return old;
+}
+#else
 static inline pte_basic_t pte_update(struct mm_struct *mm, unsigned long addr, pte_t *p,
 				     unsigned long clr, unsigned long set, int huge)
 {
@@ -242,11 +266,7 @@ static inline pte_basic_t pte_update(struct mm_struct *mm, unsigned long addr, p
 	pte_basic_t old = pte_val(*p);
 	pte_basic_t new = (old & ~(pte_basic_t)clr) | set;
 
-#if defined(CONFIG_PPC_8xx) && defined(CONFIG_PPC_16K_PAGES)
-	p->pte = p->pte1 = p->pte2 = p->pte3 = new;
-#else
 	*p = __pte(new);
-#endif
 #endif /* !PTE_ATOMIC_UPDATES */
 
 #ifdef CONFIG_44x
@@ -255,6 +275,7 @@ static inline pte_basic_t pte_update(struct mm_struct *mm, unsigned long addr, p
 #endif
 	return old;
 }
+#endif
 
 #define __HAVE_ARCH_PTEP_TEST_AND_CLEAR_YOUNG
 static inline int __ptep_test_and_clear_young(struct mm_struct *mm,
Signature · 1 line
2.25.0
#27 lore raw

PATCH v4 23/45 powerpc/mm: Reduce hugepd size for 8M hugepages on 8xx

In reply to Christophe Leroy

Commit 55c8fc3f4930 ("powerpc/8xx: reintroduce 16K pages with HW assistance") redefined pte_t as a struct of 4 pte_basic_t, because in 16K pages mode there are four identical entries in the page table. But hugepd entries for 8M pages require only one entry of size pte_basic_t. So there is no point in creating a cache for 4 entries page tables.

Calculate PTE_T_ORDER using the size of pte_basic_t instead of pte_t.

Define specific huge_pte helpers (set_huge_pte_at(), huge_pte_clear(), huge_ptep_set_wrprotect()) to write the pte in a single entry instead of using set_pte_at() which writes 4 identical entries in 16k pages mode. Also make sure that __ptep_set_access_flags() properly handle the huge_pte case.

Define set_pte_filter() inline otherwise GCC doesn't inline it anymore because it is now used twice, and that gives a pretty suboptimal code because of pte_t being a struct of 4 entries.

Those functions are also used for 512k pages which only require one entry as well allthough replicating it four times was harmless as 512k pages entries are spread every 128 bytes in the table.

---
 .../include/asm/nohash/32/hugetlb-8xx.h       | 20 ++++++++++++++
 arch/powerpc/include/asm/nohash/32/pgtable.h  |  3 ++-
 arch/powerpc/mm/hugetlbpage.c                 |  3 ++-
 arch/powerpc/mm/pgtable.c                     | 26 ++++++++++++++++---
 4 files changed, 46 insertions(+), 6 deletions(-)
arch/powerpc/include/asm/nohash/32/hugetlb-8xx.h +20 -0
index a46616937d20..785437323576 100644
@@ -41,4 +41,24 @@ static inline int check_and_get_huge_psize(int shift)
 	return shift_to_mmu_psize(shift);
 }
 
+#define __HAVE_ARCH_HUGE_SET_HUGE_PTE_AT
+void set_huge_pte_at(struct mm_struct *mm, unsigned long addr, pte_t *ptep, pte_t pte);
+
+#define __HAVE_ARCH_HUGE_PTE_CLEAR
+static inline void huge_pte_clear(struct mm_struct *mm, unsigned long addr,
+				  pte_t *ptep, unsigned long sz)
+{
+	pte_update(mm, addr, ptep, ~0UL, 0, 1);
+}
+
+#define __HAVE_ARCH_HUGE_PTEP_SET_WRPROTECT
+static inline void huge_ptep_set_wrprotect(struct mm_struct *mm,
+					   unsigned long addr, pte_t *ptep)
+{
+	unsigned long clr = ~pte_val(pte_wrprotect(__pte(~0)));
+	unsigned long set = pte_val(pte_wrprotect(__pte(0)));
+
+	pte_update(mm, addr, ptep, clr, set, 1);
+}
+
 #endif /* _ASM_POWERPC_NOHASH_32_HUGETLB_8XX_H */
arch/powerpc/include/asm/nohash/32/pgtable.h +2 -1
index 5fb3f6798e22..ff78bf25f832 100644
@@ -314,8 +314,9 @@ static inline void __ptep_set_access_flags(struct vm_area_struct *vma,
 	pte_t pte_clr = pte_mkyoung(pte_mkdirty(pte_mkwrite(pte_mkexec(__pte(~0)))));
 	unsigned long set = pte_val(entry) & pte_val(pte_set);
 	unsigned long clr = ~pte_val(entry) & ~pte_val(pte_clr);
+	int huge = psize > mmu_virtual_psize ? 1 : 0;
 
-	pte_update(vma->vm_mm, address, ptep, clr, set, 0);
+	pte_update(vma->vm_mm, address, ptep, clr, set, huge);
 
 	flush_tlb_page(vma, address);
 }
arch/powerpc/mm/hugetlbpage.c +2 -1
index d06efb946c7d..521929a371af 100644
@@ -30,7 +30,8 @@ bool hugetlb_disabled = false;
 
 #define hugepd_none(hpd)	(hpd_val(hpd) == 0)
 
-#define PTE_T_ORDER	(__builtin_ffs(sizeof(pte_t)) - __builtin_ffs(sizeof(void *)))
+#define PTE_T_ORDER	(__builtin_ffs(sizeof(pte_basic_t)) - \
+			 __builtin_ffs(sizeof(void *)))
 
 pte_t *huge_pte_offset(struct mm_struct *mm, unsigned long addr, unsigned long sz)
 {
arch/powerpc/mm/pgtable.c +22 -4
index e3759b69f81b..214a5f4beb6c 100644
@@ -100,7 +100,7 @@ static pte_t set_pte_filter_hash(pte_t pte) { return pte; }
  * as we don't have two bits to spare for _PAGE_EXEC and _PAGE_HWEXEC so
  * instead we "filter out" the exec permission for non clean pages.
  */
-static pte_t set_pte_filter(pte_t pte)
+static inline pte_t set_pte_filter(pte_t pte)
 {
 	struct page *pg;
 
@@ -249,16 +249,34 @@ int huge_ptep_set_access_flags(struct vm_area_struct *vma,
 
 #else
 		/*
-		 * Not used on non book3s64 platforms. But 8xx
-		 * can possibly use tsize derived from hstate.
+		 * Not used on non book3s64 platforms.
+		 * 8xx compares it with mmu_virtual_psize to
+		 * know if it is a huge page or not.
 		 */
-		psize = 0;
+		psize = MMU_PAGE_COUNT;
 #endif
 		__ptep_set_access_flags(vma, ptep, pte, addr, psize);
 	}
 	return changed;
 #endif
 }
+
+#if defined(CONFIG_PPC_8xx)
+void set_huge_pte_at(struct mm_struct *mm, unsigned long addr, pte_t *ptep, pte_t pte)
+{
+	/*
+	 * Make sure hardware valid bit is not set. We don't do
+	 * tlb flush for this update.
+	 */
+	VM_WARN_ON(pte_hw_valid(*ptep) && !pte_protnone(*ptep));
+
+	pte = pte_mkpte(pte);
+
+	pte = set_pte_filter(pte);
+
+	ptep->pte = pte_val(pte);
+}
+#endif
 #endif /* CONFIG_HUGETLB_PAGE */
 
 #ifdef CONFIG_DEBUG_VM
Signature · 1 line
2.25.0
#28 lore raw

PATCH v4 24/45 powerpc/8xx: Drop CONFIG_8xx_COPYBACK option

In reply to Christophe Leroy

CONFIG_8xx_COPYBACK was there to help disabling copyback cache mode for debuging hardware. But nobody will design new boards with 8xx now.

All 8xx platforms select it, so make it the default and remove the option.

Also remove the Mx_RESETVAL values which are pretty useless and hide the real value while reading code.

---
 arch/powerpc/configs/adder875_defconfig      |  1 -
 arch/powerpc/configs/ep88xc_defconfig        |  1 -
 arch/powerpc/configs/mpc866_ads_defconfig    |  1 -
 arch/powerpc/configs/mpc885_ads_defconfig    |  1 -
 arch/powerpc/configs/tqm8xx_defconfig        |  1 -
 arch/powerpc/include/asm/nohash/32/mmu-8xx.h |  2 --
 arch/powerpc/kernel/head_8xx.S               | 15 +--------------
 arch/powerpc/platforms/8xx/Kconfig           |  9 ---------
 8 files changed, 1 insertion(+), 30 deletions(-)
arch/powerpc/configs/adder875_defconfig +0 -1
index f55e23cb176c..5326bc739279 100644
@@ -10,7 +10,6 @@ CONFIG_EXPERT=y
 # CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_PPC_ADDER875=y
-CONFIG_8xx_COPYBACK=y
 CONFIG_GEN_RTC=y
 CONFIG_HZ_1000=y
 # CONFIG_SECCOMP is not set
arch/powerpc/configs/ep88xc_defconfig +0 -1
index 0e2e5e81a359..f5c3e72da719 100644
@@ -12,7 +12,6 @@ CONFIG_EXPERT=y
 # CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_PPC_EP88XC=y
-CONFIG_8xx_COPYBACK=y
 CONFIG_GEN_RTC=y
 CONFIG_HZ_100=y
 # CONFIG_SECCOMP is not set
arch/powerpc/configs/mpc866_ads_defconfig +0 -1
index 5320735395e7..5c56d36cdfc5 100644
@@ -12,7 +12,6 @@ CONFIG_EXPERT=y
 # CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_MPC86XADS=y
-CONFIG_8xx_COPYBACK=y
 CONFIG_GEN_RTC=y
 CONFIG_HZ_1000=y
 CONFIG_MATH_EMULATION=y
arch/powerpc/configs/mpc885_ads_defconfig +0 -1
index 82a008c04eae..949ff9ccda5e 100644
@@ -11,7 +11,6 @@ CONFIG_EXPERT=y
 # CONFIG_VM_EVENT_COUNTERS is not set
 # CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
-CONFIG_8xx_COPYBACK=y
 CONFIG_GEN_RTC=y
 CONFIG_HZ_100=y
 # CONFIG_SECCOMP is not set
arch/powerpc/configs/tqm8xx_defconfig +0 -1
index eda8bfb2d0a3..77857d513022 100644
@@ -15,7 +15,6 @@ CONFIG_MODULE_SRCVERSION_ALL=y
 # CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_TQM8XX=y
-CONFIG_8xx_COPYBACK=y
 # CONFIG_8xx_CPU15 is not set
 CONFIG_GEN_RTC=y
 CONFIG_HZ_100=y
arch/powerpc/include/asm/nohash/32/mmu-8xx.h +0 -2
index 76af5b0cb16e..26b7cee34dfe 100644
@@ -19,7 +19,6 @@
 #define MI_RSV4I	0x08000000	/* Reserve 4 TLB entries */
 #define MI_PPCS		0x02000000	/* Use MI_RPN prob/priv state */
 #define MI_IDXMASK	0x00001f00	/* TLB index to be loaded */
-#define MI_RESETVAL	0x00000000	/* Value of register at reset */
 
 /* These are the Ks and Kp from the PowerPC books.  For proper operation,
  * Ks = 0, Kp = 1.
@@ -95,7 +94,6 @@
 #define MD_TWAM		0x04000000	/* Use 4K page hardware assist */
 #define MD_PPCS		0x02000000	/* Use MI_RPN prob/priv state */
 #define MD_IDXMASK	0x00001f00	/* TLB index to be loaded */
-#define MD_RESETVAL	0x04000000	/* Value of register at reset */
 
 #define SPRN_M_CASID	793	/* Address space ID (context) to match */
 #define MC_ASIDMASK	0x0000000f	/* Bits used for ASID value */
arch/powerpc/kernel/head_8xx.S +1 -14
index 073a651787df..905205c79a25 100644
@@ -779,10 +779,7 @@ start_here:
 initial_mmu:
 	li	r8, 0
 	mtspr	SPRN_MI_CTR, r8		/* remove PINNED ITLB entries */
-	lis	r10, MD_RESETVAL@h
-#ifndef CONFIG_8xx_COPYBACK
-	oris	r10, r10, MD_WTDEF@h
-#endif
+	lis	r10, MD_TWAM@h
 	mtspr	SPRN_MD_CTR, r10	/* remove PINNED DTLB entries */
 
 	tlbia			/* Invalidate all TLB entries */
@@ -857,17 +854,7 @@ initial_mmu:
 	mtspr	SPRN_DC_CST, r8
 	lis	r8, IDC_ENABLE@h
 	mtspr	SPRN_IC_CST, r8
-#ifdef CONFIG_8xx_COPYBACK
-	mtspr	SPRN_DC_CST, r8
-#else
-	/* For a debug option, I left this here to easily enable
-	 * the write through cache mode
-	 */
-	lis	r8, DC_SFWT@h
 	mtspr	SPRN_DC_CST, r8
-	lis	r8, IDC_ENABLE@h
-	mtspr	SPRN_DC_CST, r8
-#endif
 	/* Disable debug mode entry on breakpoints */
 	mfspr	r8, SPRN_DER
 #ifdef CONFIG_PERF_EVENTS
arch/powerpc/platforms/8xx/Kconfig +0 -9
index e0fe670f06f6..b37de62d7e7f 100644
@@ -98,15 +98,6 @@ menu "MPC8xx CPM Options"
 # 8xx specific questions.
 comment "Generic MPC8xx Options"
 
-config 8xx_COPYBACK
-	bool "Copy-Back Data Cache (else Writethrough)"
-	help
-	  Saying Y here will cause the cache on an MPC8xx processor to be used
-	  in Copy-Back mode.  If you say N here, it is used in Writethrough
-	  mode.
-
-	  If in doubt, say Y here.
-
 config 8xx_GPIO
 	bool "GPIO API Support"
 	select GPIOLIB
Signature · 1 line
2.25.0
#29 lore raw

PATCH v4 25/45 powerpc/8xx: Prepare handlers for _PAGE_HUGE for 512k pages.

In reply to Christophe Leroy

Prepare ITLB handler to handle _PAGE_HUGE when CONFIG_HUGETLBFS is enabled. This means that the L1 entry has to be kept in r11 until L2 entry is read, in order to insert _PAGE_HUGE into it.

Also move pgd_offset helpers before pte_update() as they will be needed there in next patch.

---
 arch/powerpc/include/asm/nohash/32/pgtable.h | 13 ++++++-------
 arch/powerpc/kernel/head_8xx.S               | 15 +++++++++------
 2 files changed, 15 insertions(+), 13 deletions(-)
arch/powerpc/include/asm/nohash/32/pgtable.h +6 -7
index ff78bf25f832..9a287a95acad 100644
@@ -206,6 +206,12 @@ static inline void pmd_clear(pmd_t *pmdp)
 }
 
 
+/* to find an entry in a kernel page-table-directory */
+#define pgd_offset_k(address) pgd_offset(&init_mm, address)
+
+/* to find an entry in a page-table-directory */
+#define pgd_index(address)	 ((address) >> PGDIR_SHIFT)
+#define pgd_offset(mm, address)	 ((mm)->pgd + pgd_index(address))
 
 /*
  * PTE updates. This function is called whenever an existing
@@ -348,13 +354,6 @@ static inline int pte_young(pte_t pte)
 	pfn_to_page((__pa(pmd_val(pmd)) >> PAGE_SHIFT))
 #endif
 
-/* to find an entry in a kernel page-table-directory */
-#define pgd_offset_k(address) pgd_offset(&init_mm, address)
-
-/* to find an entry in a page-table-directory */
-#define pgd_index(address)	 ((address) >> PGDIR_SHIFT)
-#define pgd_offset(mm, address)	 ((mm)->pgd + pgd_index(address))
-
 /* Find an entry in the third-level page table.. */
 #define pte_index(address)		\
 	(((address) >> PAGE_SHIFT) & (PTRS_PER_PTE - 1))
arch/powerpc/kernel/head_8xx.S +9 -6
index 905205c79a25..adad8baadcf5 100644
@@ -196,7 +196,7 @@ SystemCall:
 
 InstructionTLBMiss:
 	mtspr	SPRN_SPRG_SCRATCH0, r10
-#if defined(ITLB_MISS_KERNEL) || defined(CONFIG_SWAP)
+#if defined(ITLB_MISS_KERNEL) || defined(CONFIG_SWAP) || defined(CONFIG_HUGETLBFS)
 	mtspr	SPRN_SPRG_SCRATCH1, r11
 #endif
 
@@ -235,16 +235,19 @@ InstructionTLBMiss:
 	rlwinm	r10, r10, 0, 20, 31
 	oris	r10, r10, (swapper_pg_dir - PAGE_OFFSET)@ha
 3:
+	mtcr	r11
 #endif
+#ifdef CONFIG_HUGETLBFS
+	lwz	r11, (swapper_pg_dir-PAGE_OFFSET)@l(r10)	/* Get level 1 entry */
+	mtspr	SPRN_MI_TWC, r11	/* Set segment attributes */
+	mtspr	SPRN_MD_TWC, r11
+#else
 	lwz	r10, (swapper_pg_dir-PAGE_OFFSET)@l(r10)	/* Get level 1 entry */
 	mtspr	SPRN_MI_TWC, r10	/* Set segment attributes */
-
 	mtspr	SPRN_MD_TWC, r10
+#endif
 	mfspr	r10, SPRN_MD_TWC
 	lwz	r10, 0(r10)	/* Get the pte */
-#ifdef ITLB_MISS_KERNEL
-	mtcr	r11
-#endif
 #ifdef CONFIG_SWAP
 	rlwinm	r11, r10, 32-5, _PAGE_PRESENT
 	and	r11, r11, r10
@@ -263,7 +266,7 @@ InstructionTLBMiss:
 
 	/* Restore registers */
 0:	mfspr	r10, SPRN_SPRG_SCRATCH0
-#if defined(ITLB_MISS_KERNEL) || defined(CONFIG_SWAP)
+#if defined(ITLB_MISS_KERNEL) || defined(CONFIG_SWAP) || defined(CONFIG_HUGETLBFS)
 	mfspr	r11, SPRN_SPRG_SCRATCH1
 #endif
 	rfi
Signature · 1 line
2.25.0
#30 lore raw

PATCH v4 26/45 powerpc/8xx: Manage 512k huge pages as standard pages.

In reply to Christophe Leroy

At the time being, 512k huge pages are handled through hugepd page tables. The PMD entry is flagged as a hugepd pointer and it means that only 512k hugepages can be managed in that 4M block. However, the hugepd table has the same size as a normal page table, and 512k entries can therefore be nested with normal pages.

On the 8xx, TLB loading is performed by software and allthough the page tables are organised to match the L1 and L2 level defined by the HW, all TLB entries have both L1 and L2 independent entries. It means that even if two TLB entries are associated with the same PMD entry, they can be loaded with different values in L1 part.

The L1 entry contains the page size (PS field):
- 00 for 4k and 16 pages
- 01 for 512k pages
- 11 for 8M pages

By adding a flag for hugepages in the PTE (_PAGE_HUGE) and copying it into the lower bit of PS, we can then manage 512k pages with normal page tables:
- PMD entry has PS=11 for 8M pages
- PMD entry has PS=00 for other pages.

As a PMD entry covers 4M areas, a PMD will either point to a hugepd table having a single entry to an 8M page, or the PMD will point to a standard page table which will have either entries to 4k or 16k or 512k pages. For 512k pages, as the L1 entry will not know it is a 512k page before the PTE is read, there will be 128 entries in the PTE as if it was 4k pages. But when loading the TLB, it will be flagged as a 512k page.

Note that we can't use pmd_ptr() in asm/nohash/32/pgtable.h because it is not defined yet.

In ITLB miss, we keep the possibility to opt it out as when kernel text is pinned and no user hugepages are used, we can save several instruction by not using r11.

In DTLB miss, that's just one instruction so it's not worth bothering with it.

---
 arch/powerpc/include/asm/nohash/32/pgtable.h | 10 ++++++---
 arch/powerpc/include/asm/nohash/32/pte-8xx.h |  4 +++-
 arch/powerpc/include/asm/nohash/pgtable.h    |  2 +-
 arch/powerpc/kernel/head_8xx.S               | 12 +++++------
 arch/powerpc/mm/hugetlbpage.c                | 22 +++++++++++++++++---
 arch/powerpc/mm/pgtable.c                    | 10 ++++++++-
 6 files changed, 44 insertions(+), 16 deletions(-)
arch/powerpc/include/asm/nohash/32/pgtable.h +7 -3
index 9a287a95acad..717f995d21b8 100644
@@ -229,8 +229,9 @@ static inline void pmd_clear(pmd_t *pmdp)
  * those implementations.
  *
  * On the 8xx, the page tables are a bit special. For 16k pages, we have
- * 4 identical entries. For other page sizes, we have a single entry in the
- * table.
+ * 4 identical entries. For 512k pages, we have 128 entries as if it was
+ * 4k pages, but they are flagged as 512k pages for the hardware.
+ * For other page sizes, we have a single entry in the table.
  */
 #ifdef CONFIG_PPC_8xx
 static inline pte_basic_t pte_update(struct mm_struct *mm, unsigned long addr, pte_t *p,
@@ -240,13 +241,16 @@ static inline pte_basic_t pte_update(struct mm_struct *mm, unsigned long addr, p
 	pte_basic_t old = pte_val(*p);
 	pte_basic_t new = (old & ~(pte_basic_t)clr) | set;
 	int num, i;
+	pmd_t *pmd = pmd_offset(pud_offset(pgd_offset(mm, addr), addr), addr);
 
 	if (!huge)
 		num = PAGE_SIZE / SZ_4K;
+	else if ((pmd_val(*pmd) & _PMD_PAGE_MASK) != _PMD_PAGE_8M)
+		num = SZ_512K / SZ_4K;
 	else
 		num = 1;
 
-	for (i = 0; i < num; i++, entry++)
+	for (i = 0; i < num; i++, entry++, new += SZ_4K)
 		*entry = new;
 
 	return old;
arch/powerpc/include/asm/nohash/32/pte-8xx.h +3 -1
index c9e4b2d90f65..66f403a7da44 100644
@@ -46,6 +46,8 @@
 #define _PAGE_NA	0x0200	/* Supervisor NA, User no access */
 #define _PAGE_RO	0x0600	/* Supervisor RO, User no access */
 
+#define _PAGE_HUGE	0x0800	/* Copied to L1 PS bit 29 */
+
 /* cache related flags non existing on 8xx */
 #define _PAGE_COHERENT	0
 #define _PAGE_WRITETHRU	0
@@ -128,7 +130,7 @@ static inline pte_t pte_mkuser(pte_t pte)
 
 static inline pte_t pte_mkhuge(pte_t pte)
 {
-	return __pte(pte_val(pte) | _PAGE_SPS);
+	return __pte(pte_val(pte) | _PAGE_SPS | _PAGE_HUGE);
 }
 
 #define pte_mkhuge pte_mkhuge
arch/powerpc/include/asm/nohash/pgtable.h +1 -1
index 7fed9dc0f147..f27c967d9269 100644
@@ -267,7 +267,7 @@ extern pgprot_t phys_mem_access_prot(struct file *file, unsigned long pfn,
 static inline int hugepd_ok(hugepd_t hpd)
 {
 #ifdef CONFIG_PPC_8xx
-	return ((hpd_val(hpd) & 0x4) != 0);
+	return ((hpd_val(hpd) & _PMD_PAGE_MASK) == _PMD_PAGE_8M);
 #else
 	/* We clear the top bit to indicate hugepd */
 	return (hpd_val(hpd) && (hpd_val(hpd) & PD_HUGE) == 0);
arch/powerpc/kernel/head_8xx.S +5 -7
index adad8baadcf5..423465b10c82 100644
@@ -239,7 +239,6 @@ InstructionTLBMiss:
 #endif
 #ifdef CONFIG_HUGETLBFS
 	lwz	r11, (swapper_pg_dir-PAGE_OFFSET)@l(r10)	/* Get level 1 entry */
-	mtspr	SPRN_MI_TWC, r11	/* Set segment attributes */
 	mtspr	SPRN_MD_TWC, r11
 #else
 	lwz	r10, (swapper_pg_dir-PAGE_OFFSET)@l(r10)	/* Get level 1 entry */
@@ -248,6 +247,10 @@ InstructionTLBMiss:
 #endif
 	mfspr	r10, SPRN_MD_TWC
 	lwz	r10, 0(r10)	/* Get the pte */
+#ifdef CONFIG_HUGETLBFS
+	rlwimi	r11, r10, 32 - 9, _PMD_PAGE_512K
+	mtspr	SPRN_MI_TWC, r11
+#endif
 #ifdef CONFIG_SWAP
 	rlwinm	r11, r10, 32-5, _PAGE_PRESENT
 	and	r11, r11, r10
@@ -353,6 +356,7 @@ DataStoreTLBMiss:
 	 * above.
 	 */
 	rlwimi	r11, r10, 0, _PAGE_GUARDED
+	rlwimi	r11, r10, 32 - 9, _PMD_PAGE_512K
 	mtspr	SPRN_MD_TWC, r11
 
 	/* Both _PAGE_ACCESSED and _PAGE_PRESENT has to be set.
@@ -584,7 +588,6 @@ FixupDAR:/* Entry point for dcbx workaround. */
 	mfspr	r11, SPRN_MD_TWC
 	lwz	r11, 0(r11)	/* Get the pte */
 	bt	28,200f		/* bit 28 = Large page (8M) */
-	bt	29,202f		/* bit 29 = Large page (8M or 512K) */
 	/* concat physical page address(r11) and page offset(r10) */
 	rlwimi	r11, r10, 0, 32 - PAGE_SHIFT, 31
 201:	lwz	r11,0(r11)
@@ -611,11 +614,6 @@ FixupDAR:/* Entry point for dcbx workaround. */
 	rlwimi	r11, r10, 0, 32 - PAGE_SHIFT_8M, 31
 	b	201b
 
-202:
-	/* concat physical page address(r11) and page offset(r10) */
-	rlwimi	r11, r10, 0, 32 - PAGE_SHIFT_512K, 31
-	b	201b
-
 144:	mfspr	r10, SPRN_DSISR
 	rlwinm	r10, r10,0,7,5	/* Clear store bit for buggy dcbst insn */
 	mtspr	SPRN_DSISR, r10
arch/powerpc/mm/hugetlbpage.c +19 -3
index 521929a371af..38bad839e608 100644
@@ -189,6 +189,9 @@ pte_t *huge_pte_alloc(struct mm_struct *mm, unsigned long addr, unsigned long sz
 	if (!hpdp)
 		return NULL;
 
+	if (IS_ENABLED(CONFIG_PPC_8xx) && sz == SZ_512K)
+		return pte_alloc_map(mm, (pmd_t *)hpdp, addr);
+
 	BUG_ON(!hugepd_none(*hpdp) && !hugepd_ok(*hpdp));
 
 	if (hugepd_none(*hpdp) && __hugepte_alloc(mm, hpdp, addr,
@@ -331,13 +334,20 @@ static void free_hugepd_range(struct mmu_gather *tlb, hugepd_t *hpdp, int pdshif
 
 	if (shift >= pdshift)
 		hugepd_free(tlb, hugepte);
-	else if (IS_ENABLED(CONFIG_PPC_8xx))
-		pgtable_free_tlb(tlb, hugepte, 0);
 	else
 		pgtable_free_tlb(tlb, hugepte,
 				 get_hugepd_cache_index(pdshift - shift));
 }
 
+static void hugetlb_free_pte_range(struct mmu_gather *tlb, pmd_t *pmd, unsigned long addr)
+{
+	pgtable_t token = pmd_pgtable(*pmd);
+
+	pmd_clear(pmd);
+	pte_free_tlb(tlb, token, addr);
+	mm_dec_nr_ptes(tlb->mm);
+}
+
 static void hugetlb_free_pmd_range(struct mmu_gather *tlb, pud_t *pud,
 				   unsigned long addr, unsigned long end,
 				   unsigned long floor, unsigned long ceiling)
@@ -353,11 +363,17 @@ static void hugetlb_free_pmd_range(struct mmu_gather *tlb, pud_t *pud,
 		pmd = pmd_offset(pud, addr);
 		next = pmd_addr_end(addr, end);
 		if (!is_hugepd(__hugepd(pmd_val(*pmd)))) {
+			if (pmd_none_or_clear_bad(pmd))
+				continue;
+
 			/*
 			 * if it is not hugepd pointer, we should already find
 			 * it cleared.
 			 */
-			WARN_ON(!pmd_none_or_clear_bad(pmd));
+			WARN_ON(!IS_ENABLED(CONFIG_PPC_8xx));
+
+			hugetlb_free_pte_range(tlb, pmd, addr);
+
 			continue;
 		}
 		/*
arch/powerpc/mm/pgtable.c +9 -1
index 214a5f4beb6c..60c4b8ff046c 100644
@@ -264,6 +264,12 @@ int huge_ptep_set_access_flags(struct vm_area_struct *vma,
 #if defined(CONFIG_PPC_8xx)
 void set_huge_pte_at(struct mm_struct *mm, unsigned long addr, pte_t *ptep, pte_t pte)
 {
+	pmd_t *pmd = pmd_ptr(mm, addr);
+	pte_basic_t val;
+	pte_basic_t *entry = &ptep->pte;
+	int num = is_hugepd(*((hugepd_t *)pmd)) ? 1 : SZ_512K / SZ_4K;
+	int i;
+
 	/*
 	 * Make sure hardware valid bit is not set. We don't do
 	 * tlb flush for this update.
@@ -274,7 +280,9 @@ void set_huge_pte_at(struct mm_struct *mm, unsigned long addr, pte_t *ptep, pte_
 
 	pte = set_pte_filter(pte);
 
-	ptep->pte = pte_val(pte);
+	val = pte_val(pte);
+	for (i = 0; i < num; i++, entry++, val += SZ_4K)
+		*entry = val;
 }
 #endif
 #endif /* CONFIG_HUGETLB_PAGE */
Signature · 1 line
2.25.0
#31 lore raw

PATCH v4 27/45 powerpc/8xx: Only 8M pages are hugepte pages now

In reply to Christophe Leroy

512k pages are now standard pages, so only 8M pages are hugepte.

No more handling of normal page tables through hugepd allocation and freeing, and hugepte helpers can also be simplified.

---
 arch/powerpc/include/asm/nohash/32/hugetlb-8xx.h |  7 +++----
 arch/powerpc/mm/hugetlbpage.c                    | 16 +++-------------
 2 files changed, 6 insertions(+), 17 deletions(-)
arch/powerpc/include/asm/nohash/32/hugetlb-8xx.h +3 -4
index 785437323576..1c7d4693a78e 100644
@@ -13,13 +13,13 @@ static inline pte_t *hugepd_page(hugepd_t hpd)
 
 static inline unsigned int hugepd_shift(hugepd_t hpd)
 {
-	return ((hpd_val(hpd) & _PMD_PAGE_MASK) >> 1) + 17;
+	return PAGE_SHIFT_8M;
 }
 
 static inline pte_t *hugepte_offset(hugepd_t hpd, unsigned long addr,
 				    unsigned int pdshift)
 {
-	unsigned long idx = (addr & ((1UL << pdshift) - 1)) >> PAGE_SHIFT;
+	unsigned long idx = (addr & (SZ_4M - 1)) >> PAGE_SHIFT;
 
 	return hugepd_page(hpd) + idx;
 }
@@ -32,8 +32,7 @@ static inline void flush_hugetlb_page(struct vm_area_struct *vma,
 
 static inline void hugepd_populate(hugepd_t *hpdp, pte_t *new, unsigned int pshift)
 {
-	*hpdp = __hugepd(__pa(new) | _PMD_USER | _PMD_PRESENT |
-			 (pshift == PAGE_SHIFT_8M ? _PMD_PAGE_8M : _PMD_PAGE_512K));
+	*hpdp = __hugepd(__pa(new) | _PMD_USER | _PMD_PRESENT | _PMD_PAGE_8M);
 }
 
 static inline int check_and_get_huge_psize(int shift)
arch/powerpc/mm/hugetlbpage.c +3 -13
index 38bad839e608..cfacd364c7aa 100644
@@ -54,24 +54,17 @@ static int __hugepte_alloc(struct mm_struct *mm, hugepd_t *hpdp,
 	if (pshift >= pdshift) {
 		cachep = PGT_CACHE(PTE_T_ORDER);
 		num_hugepd = 1 << (pshift - pdshift);
-		new = NULL;
-	} else if (IS_ENABLED(CONFIG_PPC_8xx)) {
-		cachep = NULL;
-		num_hugepd = 1;
-		new = pte_alloc_one(mm);
 	} else {
 		cachep = PGT_CACHE(pdshift - pshift);
 		num_hugepd = 1;
-		new = NULL;
 	}
 
-	if (!cachep && !new) {
+	if (!cachep) {
 		WARN_ONCE(1, "No page table cache created for hugetlb tables");
 		return -ENOMEM;
 	}
 
-	if (cachep)
-		new = kmem_cache_alloc(cachep, pgtable_gfp_flags(mm, GFP_KERNEL));
+	new = kmem_cache_alloc(cachep, pgtable_gfp_flags(mm, GFP_KERNEL));
 
 	BUG_ON(pshift > HUGEPD_SHIFT_MASK);
 	BUG_ON((unsigned long)new & HUGEPD_SHIFT_MASK);
@@ -102,10 +95,7 @@ static int __hugepte_alloc(struct mm_struct *mm, hugepd_t *hpdp,
 	if (i < num_hugepd) {
 		for (i = i - 1 ; i >= 0; i--, hpdp--)
 			*hpdp = __hugepd(0);
-		if (cachep)
-			kmem_cache_free(cachep, new);
-		else
-			pte_free(mm, new);
+		kmem_cache_free(cachep, new);
 	} else {
 		kmemleak_ignore(new);
 	}
Signature · 1 line
2.25.0
#32 lore raw

PATCH v4 28/45 powerpc/8xx: MM_SLICE is not needed anymore

In reply to Christophe Leroy

As the 8xx now manages 512k pages in standard page tables, it doesn't need CONFIG_PPC_MM_SLICES anymore.

Don't select it anymore and remove all related code.

---
 arch/powerpc/include/asm/nohash/32/mmu-8xx.h | 64 --------------------
 arch/powerpc/include/asm/nohash/32/slice.h   | 20 ------
 arch/powerpc/include/asm/slice.h             |  2 -
 arch/powerpc/platforms/Kconfig.cputype       |  1 -
 4 files changed, 87 deletions(-)
 delete mode 100644 arch/powerpc/include/asm/nohash/32/slice.h
arch/powerpc/include/asm/nohash/32/mmu-8xx.h +0 -64
index 26b7cee34dfe..a092e6434bda 100644
@@ -176,12 +176,6 @@
  */
 #define SPRN_M_TW	799
 
-#ifdef CONFIG_PPC_MM_SLICES
-#include <asm/nohash/32/slice.h>
-#define SLICE_ARRAY_SIZE	(1 << (32 - SLICE_LOW_SHIFT - 1))
-#define LOW_SLICE_ARRAY_SZ	SLICE_ARRAY_SIZE
-#endif
-
 #if defined(CONFIG_PPC_4K_PAGES)
 #define mmu_virtual_psize	MMU_PAGE_4K
 #elif defined(CONFIG_PPC_16K_PAGES)
@@ -199,71 +193,13 @@
 
 #include <linux/mmdebug.h>
 
-struct slice_mask {
-	u64 low_slices;
-	DECLARE_BITMAP(high_slices, 0);
-};
-
 typedef struct {
 	unsigned int id;
 	unsigned int active;
 	unsigned long vdso_base;
-#ifdef CONFIG_PPC_MM_SLICES
-	u16 user_psize;		/* page size index */
-	unsigned char low_slices_psize[SLICE_ARRAY_SIZE];
-	unsigned char high_slices_psize[0];
-	unsigned long slb_addr_limit;
-	struct slice_mask mask_base_psize; /* 4k or 16k */
-	struct slice_mask mask_512k;
-	struct slice_mask mask_8m;
-#endif
 	void *pte_frag;
 } mm_context_t;
 
-#ifdef CONFIG_PPC_MM_SLICES
-static inline u16 mm_ctx_user_psize(mm_context_t *ctx)
-{
-	return ctx->user_psize;
-}
-
-static inline void mm_ctx_set_user_psize(mm_context_t *ctx, u16 user_psize)
-{
-	ctx->user_psize = user_psize;
-}
-
-static inline unsigned char *mm_ctx_low_slices(mm_context_t *ctx)
-{
-	return ctx->low_slices_psize;
-}
-
-static inline unsigned char *mm_ctx_high_slices(mm_context_t *ctx)
-{
-	return ctx->high_slices_psize;
-}
-
-static inline unsigned long mm_ctx_slb_addr_limit(mm_context_t *ctx)
-{
-	return ctx->slb_addr_limit;
-}
-
-static inline void mm_ctx_set_slb_addr_limit(mm_context_t *ctx, unsigned long limit)
-{
-	ctx->slb_addr_limit = limit;
-}
-
-static inline struct slice_mask *slice_mask_for_size(mm_context_t *ctx, int psize)
-{
-	if (psize == MMU_PAGE_512K)
-		return &ctx->mask_512k;
-	if (psize == MMU_PAGE_8M)
-		return &ctx->mask_8m;
-
-	BUG_ON(psize != mmu_virtual_psize);
-
-	return &ctx->mask_base_psize;
-}
-#endif /* CONFIG_PPC_MM_SLICE */
-
 #define PHYS_IMMR_BASE (mfspr(SPRN_IMMR) & 0xfff80000)
 #define VIRT_IMMR_BASE (__fix_to_virt(FIX_IMMR_BASE))
 
arch/powerpc/include/asm/nohash/32/slice.h deleted +0 -20
deleted file mode 100644
index 39eb0154ae2d..000000000000
@@ -1,20 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef _ASM_POWERPC_NOHASH_32_SLICE_H
-#define _ASM_POWERPC_NOHASH_32_SLICE_H
-
-#ifdef CONFIG_PPC_MM_SLICES
-
-#define SLICE_LOW_SHIFT		26	/* 64 slices */
-#define SLICE_LOW_TOP		(0x100000000ull)
-#define SLICE_NUM_LOW		(SLICE_LOW_TOP >> SLICE_LOW_SHIFT)
-#define GET_LOW_SLICE_INDEX(addr)	((addr) >> SLICE_LOW_SHIFT)
-
-#define SLICE_HIGH_SHIFT	0
-#define SLICE_NUM_HIGH		0ul
-#define GET_HIGH_SLICE_INDEX(addr)	(addr & 0)
-
-#define SLB_ADDR_LIMIT_DEFAULT	DEFAULT_MAP_WINDOW
-
-#endif /* CONFIG_PPC_MM_SLICES */
-
-#endif /* _ASM_POWERPC_NOHASH_32_SLICE_H */
arch/powerpc/include/asm/slice.h +0 -2
index c6f466f4c241..0bdd9c62eca0 100644
@@ -4,8 +4,6 @@
 
 #ifdef CONFIG_PPC_BOOK3S_64
 #include <asm/book3s/64/slice.h>
-#elif defined(CONFIG_PPC_MMU_NOHASH_32)
-#include <asm/nohash/32/slice.h>
 #endif
 
 #ifndef __ASSEMBLY__
arch/powerpc/platforms/Kconfig.cputype +0 -1
index 27a81c291be8..5774a55a9c58 100644
@@ -55,7 +55,6 @@ config PPC_8xx
 	select SYS_SUPPORTS_HUGETLBFS
 	select PPC_HAVE_KUEP
 	select PPC_HAVE_KUAP
-	select PPC_MM_SLICES if HUGETLB_PAGE
 	select HAVE_ARCH_VMAP_STACK
 
 config 40x
Signature · 1 line
2.25.0
#33 lore raw

PATCH v4 29/45 powerpc/8xx: Move PPC_PIN_TLB options into 8xx Kconfig

In reply to Christophe Leroy

PPC_PIN_TLB options are dedicated to the 8xx, move them into the 8xx Kconfig.

While we are at it, add some text to explain what it does.

---
 arch/powerpc/Kconfig               | 20 ---------------
 arch/powerpc/platforms/8xx/Kconfig | 41 ++++++++++++++++++++++++++++++
 2 files changed, 41 insertions(+), 20 deletions(-)
arch/powerpc/Kconfig +0 -20
index 30e2111ca15d..1d4ef4f27dec 100644
@@ -1227,26 +1227,6 @@ config TASK_SIZE
 	hex "Size of user task space" if TASK_SIZE_BOOL
 	default "0x80000000" if PPC_8xx
 	default "0xc0000000"
-
-config PIN_TLB
-	bool "Pinned Kernel TLBs (860 ONLY)"
-	depends on ADVANCED_OPTIONS && PPC_8xx && \
-		   !DEBUG_PAGEALLOC && !STRICT_KERNEL_RWX
-
-config PIN_TLB_DATA
-	bool "Pinned TLB for DATA"
-	depends on PIN_TLB
-	default y
-
-config PIN_TLB_IMMR
-	bool "Pinned TLB for IMMR"
-	depends on PIN_TLB || PPC_EARLY_DEBUG_CPM
-	default y
-
-config PIN_TLB_TEXT
-	bool "Pinned TLB for TEXT"
-	depends on PIN_TLB
-	default y
 endmenu
 
 if PPC64
arch/powerpc/platforms/8xx/Kconfig +41 -0

45 lines not on this page · raw message

Signature · 1 line
2.25.0
#34 lore raw

PATCH v4 30/45 powerpc/8xx: Add function to set pinned TLBs

In reply to Christophe Leroy

Pinned TLBs cannot be modified when the MMU is enabled.

Create a function to rewrite the pinned TLB entries with MMU off.

To set pinned TLB, we have to turn off MMU, disable pinning, do a TLB flush (Either with tlbie and tlbia) then reprogam the TLB entries, enable pinning and turn on MMU.

If using tlbie, it cleared entries in both instruction and data TLB regardless whether pinning is disabled or not.
If using tlbia, it clears all entries of the TLB which has disabled pinning.

To make it easy, just clear all entries in both TLBs, and reprogram them.

The function takes two arguments, the top of the memory to consider and whether data is RO under _sinittext.
When DEBUG_PAGEALLOC is set, the top is the end of kernel rodata. Otherwise, that's the top of physical RAM.

Everything below _sinittext is set RX, over _sinittext that's RW.

---
v2: Function rewritten to manage all entries at once.

---
 arch/powerpc/include/asm/nohash/32/mmu-8xx.h |   2 +
 arch/powerpc/kernel/head_8xx.S               | 103 +++++++++++++++++++
 2 files changed, 105 insertions(+)
arch/powerpc/include/asm/nohash/32/mmu-8xx.h +2 -0
index a092e6434bda..4d3ef3841b00 100644
@@ -193,6 +193,8 @@
 
 #include <linux/mmdebug.h>
 
+void mmu_pin_tlb(unsigned long top, bool readonly);
+
 typedef struct {
 	unsigned int id;
 	unsigned int active;
arch/powerpc/kernel/head_8xx.S +103 -0

115 lines not on this page · raw message

Signature · 1 line
2.25.0
#35 lore raw

PATCH v4 31/45 powerpc/8xx: Don't set IMMR map anymore at boot

In reply to Christophe Leroy

Only early debug requires IMMR to be mapped early.

No need to set it up and pin it in assembly. Map it through page tables at udbg init when necessary.

If CONFIG_PIN_TLB_IMMR is selected, pin it once we don't need the 32 Mb pinned RAM anymore.

---
v2: Disable TLB reservation to modify entry 31

---
 arch/powerpc/kernel/head_8xx.S     | 39 +++++++++++++-----------------
 arch/powerpc/mm/mmu_decl.h         |  4 +++
 arch/powerpc/mm/nohash/8xx.c       | 15 +++++++++---
 arch/powerpc/platforms/8xx/Kconfig |  2 +-
 arch/powerpc/sysdev/cpm_common.c   |  2 ++
 5 files changed, 35 insertions(+), 27 deletions(-)
arch/powerpc/kernel/head_8xx.S +17 -22
index c9e3d54e6a6f..d607f4b53e0f 100644
@@ -749,6 +749,23 @@ start_here:
 	rfi
 /* Load up the kernel context */
 2:
+#ifdef CONFIG_PIN_TLB_IMMR
+	lis	r0, MD_TWAM@h
+	oris	r0, r0, 0x1f00
+	mtspr	SPRN_MD_CTR, r0
+	LOAD_REG_IMMEDIATE(r0, VIRT_IMMR_BASE | MD_EVALID)
+	tlbie	r0
+	mtspr	SPRN_MD_EPN, r0
+	LOAD_REG_IMMEDIATE(r0, MD_SVALID | MD_PS512K | MD_GUARDED)
+	mtspr	SPRN_MD_TWC, r0
+	mfspr   r0, SPRN_IMMR
+	rlwinm	r0, r0, 0, 0xfff80000
+	ori	r0, r0, 0xf0 | _PAGE_DIRTY | _PAGE_SPS | _PAGE_SH | \
+			_PAGE_NO_CACHE | _PAGE_PRESENT
+	mtspr	SPRN_MD_RPN, r0
+	lis	r0, (MD_TWAM | MD_RSV4I)@h
+	mtspr	SPRN_MD_CTR, r0
+#endif
 	tlbia			/* Clear all TLB entries */
 	sync			/* wait for tlbia/tlbie to finish */
 
@@ -797,28 +814,6 @@ initial_mmu:
 	ori	r8, r8, MD_APG_INIT@l
 	mtspr	SPRN_MD_AP, r8
 
-	/* Map a 512k page for the IMMR to get the processor
-	 * internal registers (among other things).
-	 */
-#ifdef CONFIG_PIN_TLB_IMMR
-	oris	r10, r10, MD_RSV4I@h
-	ori	r10, r10, 0x1c00
-	mtspr	SPRN_MD_CTR, r10
-
-	mfspr	r9, 638			/* Get current IMMR */
-	andis.	r9, r9, 0xfff8		/* Get 512 kbytes boundary */
-
-	lis	r8, VIRT_IMMR_BASE@h	/* Create vaddr for TLB */
-	ori	r8, r8, MD_EVALID	/* Mark it valid */
-	mtspr	SPRN_MD_EPN, r8
-	li	r8, MD_PS512K | MD_GUARDED	/* Set 512k byte page */
-	ori	r8, r8, MD_SVALID	/* Make it valid */
-	mtspr	SPRN_MD_TWC, r8
-	mr	r8, r9			/* Create paddr for TLB */
-	ori	r8, r8, MI_BOOTINIT|0x2 /* Inhibit cache -- Cort */
-	mtspr	SPRN_MD_RPN, r8
-#endif
-
 	/* Now map the lower RAM (up to 32 Mbytes) into the ITLB. */
 #ifdef CONFIG_PIN_TLB_TEXT
 	lis	r8, MI_RSV4I@h
arch/powerpc/mm/mmu_decl.h +4 -0
index 7097e07a209a..1b6d39e9baed 100644
@@ -182,6 +182,10 @@ static inline void mmu_mark_initmem_nx(void) { }
 static inline void mmu_mark_rodata_ro(void) { }
 #endif
 
+#ifdef CONFIG_PPC_8xx
+void __init mmu_mapin_immr(void);
+#endif
+
 #ifdef CONFIG_PPC_DEBUG_WX
 void ptdump_check_wx(void);
 #else
arch/powerpc/mm/nohash/8xx.c +11 -4
index bda5290af751..a9313aa6f1cd 100644
@@ -66,7 +66,7 @@ void __init MMU_init_hw(void)
 	if (IS_ENABLED(CONFIG_PIN_TLB_DATA)) {
 		unsigned long ctr = mfspr(SPRN_MD_CTR) & 0xfe000000;
 		unsigned long flags = 0xf0 | MD_SPS16K | _PAGE_SH | _PAGE_DIRTY;
-		int i = IS_ENABLED(CONFIG_PIN_TLB_IMMR) ? 29 : 28;
+		int i = 28;
 		unsigned long addr = 0;
 		unsigned long mem = total_lowmem;
 
@@ -81,12 +81,19 @@ void __init MMU_init_hw(void)
 	}
 }
 
-static void __init mmu_mapin_immr(void)
+static bool immr_is_mapped __initdata;
+
+void __init mmu_mapin_immr(void)
 {
 	unsigned long p = PHYS_IMMR_BASE;
 	unsigned long v = VIRT_IMMR_BASE;
 	int offset;
 
+	if (immr_is_mapped)
+		return;
+
+	immr_is_mapped = true;
+
 	for (offset = 0; offset < IMMR_SIZE; offset += PAGE_SIZE)
 		map_kernel_page(v + offset, p + offset, PAGE_KERNEL_NCG);
 }
@@ -122,9 +129,10 @@ unsigned long __init mmu_mapin_ram(unsigned long base, unsigned long top)
 {
 	unsigned long mapped;
 
+	mmu_mapin_immr();
+
 	if (__map_without_ltlbs) {
 		mapped = 0;
-		mmu_mapin_immr();
 		if (!IS_ENABLED(CONFIG_PIN_TLB_IMMR))
 			patch_instruction_site(&patch__dtlbmiss_immr_jmp, ppc_inst(PPC_INST_NOP));
 		if (!IS_ENABLED(CONFIG_PIN_TLB_TEXT))
@@ -143,7 +151,6 @@ unsigned long __init mmu_mapin_ram(unsigned long base, unsigned long top)
 		 */
 		mmu_mapin_ram_chunk(0, einittext8, PAGE_KERNEL_X);
 		mmu_mapin_ram_chunk(einittext8, mapped, PAGE_KERNEL);
-		mmu_mapin_immr();
 	}
 
 	mmu_patch_cmp_limit(&patch__dtlbmiss_linmem_top, mapped);
arch/powerpc/platforms/8xx/Kconfig +1 -1
index 0d036cd868ef..04ea1a8a0bdc 100644
@@ -187,7 +187,7 @@ config PIN_TLB_DATA
 
 config PIN_TLB_IMMR
 	bool "Pinned TLB for IMMR"
-	depends on PIN_TLB || PPC_EARLY_DEBUG_CPM
+	depends on PIN_TLB
 	default y
 	help
 	  This pins the IMMR area with a 512kbytes page. In case
arch/powerpc/sysdev/cpm_common.c +2 -0
index 71660bacb264..7dc1960f8bdb 100644
@@ -68,6 +68,8 @@ static void udbg_putc_cpm(char c)
 void __init udbg_init_cpm(void)
 {
 #ifdef CONFIG_PPC_8xx
+	mmu_mapin_immr();
+
 	cpm_udbg_txdesc = (u32 __iomem __force *)
 			  (CONFIG_PPC_EARLY_DEBUG_CPM_ADDR - PHYS_IMMR_BASE +
 			   VIRT_IMMR_BASE);
Signature · 1 line
2.25.0
#36 lore raw

PATCH v4 32/45 powerpc/8xx: Always pin TLBs at startup.

In reply to Christophe Leroy

At startup, map 32 Mbytes of memory through 4 pages of 8M, and PIN them inconditionnaly. They need to be pinned because KASAN is using page tables early and the TLBs might be dynamically replaced otherwise.

Remove RSV4I flag after installing mappings unless CONFIG_PIN_TLB_XXXX is selected.

---
 arch/powerpc/kernel/head_8xx.S | 31 +++++++++++++++++--------------
 arch/powerpc/mm/nohash/8xx.c   | 19 +------------------
 2 files changed, 18 insertions(+), 32 deletions(-)
arch/powerpc/kernel/head_8xx.S +17 -14
index d607f4b53e0f..b0cceee6405c 100644
@@ -765,6 +765,14 @@ start_here:
 	mtspr	SPRN_MD_RPN, r0
 	lis	r0, (MD_TWAM | MD_RSV4I)@h
 	mtspr	SPRN_MD_CTR, r0
+#endif
+#ifndef CONFIG_PIN_TLB_TEXT
+	li	r0, 0
+	mtspr	SPRN_MI_CTR, r0
+#endif
+#if !defined(CONFIG_PIN_TLB_DATA) && !defined(CONFIG_PIN_TLB_IMMR)
+	lis	r0, MD_TWAM@h
+	mtspr	SPRN_MD_CTR, r0
 #endif
 	tlbia			/* Clear all TLB entries */
 	sync			/* wait for tlbia/tlbie to finish */
@@ -802,10 +810,6 @@ initial_mmu:
 	mtspr	SPRN_MD_CTR, r10	/* remove PINNED DTLB entries */
 
 	tlbia			/* Invalidate all TLB entries */
-#ifdef CONFIG_PIN_TLB_DATA
-	oris	r10, r10, MD_RSV4I@h
-	mtspr	SPRN_MD_CTR, r10	/* Set data TLB control */
-#endif
 
 	lis	r8, MI_APG_INIT@h	/* Set protection modes */
 	ori	r8, r8, MI_APG_INIT@l
@@ -814,33 +818,32 @@ initial_mmu:
 	ori	r8, r8, MD_APG_INIT@l
 	mtspr	SPRN_MD_AP, r8
 
-	/* Now map the lower RAM (up to 32 Mbytes) into the ITLB. */
-#ifdef CONFIG_PIN_TLB_TEXT
+	/* Map the lower RAM (up to 32 Mbytes) into the ITLB and DTLB */
 	lis	r8, MI_RSV4I@h
 	ori	r8, r8, 0x1c00
-#endif
+	oris	r12, r10, MD_RSV4I@h
+	ori	r12, r12, 0x1c00
 	li	r9, 4				/* up to 4 pages of 8M */
 	mtctr	r9
 	lis	r9, KERNELBASE@h		/* Create vaddr for TLB */
 	li	r10, MI_PS8MEG | MI_SVALID	/* Set 8M byte page */
 	li	r11, MI_BOOTINIT		/* Create RPN for address 0 */
-	lis	r12, _einittext@h
-	ori	r12, r12, _einittext@l
 1:
-#ifdef CONFIG_PIN_TLB_TEXT
 	mtspr	SPRN_MI_CTR, r8	/* Set instruction MMU control */
 	addi	r8, r8, 0x100
-#endif
-
 	ori	r0, r9, MI_EVALID		/* Mark it valid */
 	mtspr	SPRN_MI_EPN, r0
 	mtspr	SPRN_MI_TWC, r10
 	mtspr	SPRN_MI_RPN, r11		/* Store TLB entry */
+	mtspr	SPRN_MD_CTR, r12
+	addi	r12, r12, 0x100
+	mtspr	SPRN_MD_EPN, r0
+	mtspr	SPRN_MD_TWC, r10
+	mtspr	SPRN_MD_RPN, r11
 	addis	r9, r9, 0x80
 	addis	r11, r11, 0x80
 
-	cmpl	cr0, r9, r12
-	bdnzf	gt, 1b
+	bdnz	1b
 
 	/* Since the cache is enabled according to the information we
 	 * just loaded into the TLB, invalidate and enable the caches here.
arch/powerpc/mm/nohash/8xx.c +1 -18
index a9313aa6f1cd..2c480e35b426 100644
@@ -62,23 +62,6 @@ unsigned long p_block_mapped(phys_addr_t pa)
  */
 void __init MMU_init_hw(void)
 {
-	/* PIN up to the 3 first 8Mb after IMMR in DTLB table */
-	if (IS_ENABLED(CONFIG_PIN_TLB_DATA)) {
-		unsigned long ctr = mfspr(SPRN_MD_CTR) & 0xfe000000;
-		unsigned long flags = 0xf0 | MD_SPS16K | _PAGE_SH | _PAGE_DIRTY;
-		int i = 28;
-		unsigned long addr = 0;
-		unsigned long mem = total_lowmem;
-
-		for (; i < 32 && mem >= LARGE_PAGE_SIZE_8M; i++) {
-			mtspr(SPRN_MD_CTR, ctr | (i << 8));
-			mtspr(SPRN_MD_EPN, (unsigned long)__va(addr) | MD_EVALID);
-			mtspr(SPRN_MD_TWC, MD_PS8MEG | MD_SVALID);
-			mtspr(SPRN_MD_RPN, addr | flags | _PAGE_PRESENT);
-			addr += LARGE_PAGE_SIZE_8M;
-			mem -= LARGE_PAGE_SIZE_8M;
-		}
-	}
 }
 
 static bool immr_is_mapped __initdata;
@@ -226,7 +209,7 @@ void __init setup_initial_memory_limit(phys_addr_t first_memblock_base,
 	BUG_ON(first_memblock_base != 0);
 
 	/* 8xx can only access 32MB at the moment */
-	memblock_set_current_limit(min_t(u64, first_memblock_size, 0x02000000));
+	memblock_set_current_limit(min_t(u64, first_memblock_size, SZ_32M));
 }
 
 /*
Signature · 1 line
2.25.0
#37 lore raw

PATCH v4 33/45 powerpc/8xx: Drop special handling of Linear and IMMR mappings in I/D TLB handlers

In reply to Christophe Leroy

Up to now, linear and IMMR mappings are managed via huge TLB entries through specific code directly in TLB miss handlers. This implies some patching of the TLB miss handlers at startup, and a lot of dedicated code.

Remove all this specific dedicated code.

For now we are back to normal handling via standard 4k pages. In the next patches, linear memory mapping and IMMR mapping will be managed through huge pages.

---
 arch/powerpc/kernel/head_8xx.S |  29 +--------
 arch/powerpc/mm/nohash/8xx.c   | 106 +--------------------------------
 2 files changed, 3 insertions(+), 132 deletions(-)
arch/powerpc/kernel/head_8xx.S +2 -27
index b0cceee6405c..d1546f379757 100644
@@ -207,31 +207,21 @@ InstructionTLBMiss:
 	mfspr	r10, SPRN_SRR0	/* Get effective address of fault */
 	INVALIDATE_ADJACENT_PAGES_CPU15(r10)
 	mtspr	SPRN_MD_EPN, r10
-	/* Only modules will cause ITLB Misses as we always
-	 * pin the first 8MB of kernel memory */
 #ifdef ITLB_MISS_KERNEL
 	mfcr	r11
-#if defined(SIMPLE_KERNEL_ADDRESS) && defined(CONFIG_PIN_TLB_TEXT)
+#if defined(SIMPLE_KERNEL_ADDRESS)
 	cmpi	cr0, r10, 0	/* Address >= 0x80000000 */
 #else
 	rlwinm	r10, r10, 16, 0xfff8
 	cmpli	cr0, r10, PAGE_OFFSET@h
-#ifndef CONFIG_PIN_TLB_TEXT
-	/* It is assumed that kernel code fits into the first 32M */
-0:	cmpli	cr7, r10, (PAGE_OFFSET + 0x2000000)@h
-	patch_site	0b, patch__itlbmiss_linmem_top
-#endif
 #endif
 #endif
 	mfspr	r10, SPRN_M_TWB	/* Get level 1 table */
 #ifdef ITLB_MISS_KERNEL
-#if defined(SIMPLE_KERNEL_ADDRESS) && defined(CONFIG_PIN_TLB_TEXT)
+#if defined(SIMPLE_KERNEL_ADDRESS)
 	bge+	3f
 #else
 	blt+	3f
-#endif
-#ifndef CONFIG_PIN_TLB_TEXT
-	blt	cr7, ITLBMissLinear
 #endif
 	rlwinm	r10, r10, 0, 20, 31
 	oris	r10, r10, (swapper_pg_dir - PAGE_OFFSET)@ha
@@ -327,19 +317,9 @@ DataStoreTLBMiss:
 	mfspr	r10, SPRN_MD_EPN
 	rlwinm	r10, r10, 16, 0xfff8
 	cmpli	cr0, r10, PAGE_OFFSET@h
-#ifndef CONFIG_PIN_TLB_IMMR
-	cmpli	cr6, r10, VIRT_IMMR_BASE@h
-#endif
-0:	cmpli	cr7, r10, (PAGE_OFFSET + 0x2000000)@h
-	patch_site	0b, patch__dtlbmiss_linmem_top
 
 	mfspr	r10, SPRN_M_TWB	/* Get level 1 table */
 	blt+	3f
-#ifndef CONFIG_PIN_TLB_IMMR
-0:	beq-	cr6, DTLBMissIMMR
-	patch_site	0b, patch__dtlbmiss_immr_jmp
-#endif
-	blt	cr7, DTLBMissLinear
 	rlwinm	r10, r10, 0, 20, 31
 	oris	r10, r10, (swapper_pg_dir - PAGE_OFFSET)@ha
 3:
@@ -571,14 +551,9 @@ FixupDAR:/* Entry point for dcbx workaround. */
 	cmpli	cr1, r11, PAGE_OFFSET@h
 	mfspr	r11, SPRN_M_TWB	/* Get level 1 table */
 	blt+	cr1, 3f
-	rlwinm	r11, r10, 16, 0xfff8
-
-0:	cmpli	cr7, r11, (PAGE_OFFSET + 0x1800000)@h
-	patch_site	0b, patch__fixupdar_linmem_top
 
 	/* create physical page address from effective address */
 	tophys(r11, r10)
-	blt-	cr7, 201f
 	mfspr	r11, SPRN_M_TWB	/* Get level 1 table */
 	rlwinm	r11, r11, 0, 20, 31
 	oris	r11, r11, (swapper_pg_dir - PAGE_OFFSET)@ha
arch/powerpc/mm/nohash/8xx.c +1 -105

131 lines not on this page · raw message

Signature · 1 line
2.25.0
#38 lore raw

PATCH v4 34/45 powerpc/8xx: Remove now unused TLB miss functions

In reply to Christophe Leroy

The code to setup linear and IMMR mapping via huge TLB entries is not called anymore. Remove it.

Also remove the handling of removed code exits in the perf driver.

---
 arch/powerpc/include/asm/nohash/32/mmu-8xx.h |  8 +-
 arch/powerpc/kernel/head_8xx.S               | 83 --------------------
 arch/powerpc/perf/8xx-pmu.c                  | 10 ---
 3 files changed, 1 insertion(+), 100 deletions(-)
arch/powerpc/include/asm/nohash/32/mmu-8xx.h +1 -7
index 4d3ef3841b00..e82368838416 100644
@@ -240,13 +240,7 @@ static inline unsigned int mmu_psize_to_shift(unsigned int mmu_psize)
 }
 
 /* patch sites */
-extern s32 patch__itlbmiss_linmem_top, patch__itlbmiss_linmem_top8;
-extern s32 patch__dtlbmiss_linmem_top, patch__dtlbmiss_immr_jmp;
-extern s32 patch__fixupdar_linmem_top;
-extern s32 patch__dtlbmiss_romem_top, patch__dtlbmiss_romem_top8;
-
-extern s32 patch__itlbmiss_exit_1, patch__itlbmiss_exit_2;
-extern s32 patch__dtlbmiss_exit_1, patch__dtlbmiss_exit_2, patch__dtlbmiss_exit_3;
+extern s32 patch__itlbmiss_exit_1, patch__dtlbmiss_exit_1;
 extern s32 patch__itlbmiss_perf, patch__dtlbmiss_perf;
 
 #endif /* !__ASSEMBLY__ */
arch/powerpc/kernel/head_8xx.S +0 -83

95 lines not on this page · raw message

arch/powerpc/perf/8xx-pmu.c +0 -10
index acc27fc63eb7..e53c3c161257 100644
@@ -100,9 +100,6 @@ static int mpc8xx_pmu_add(struct perf_event *event, int flags)
 			unsigned long target = patch_site_addr(&patch__itlbmiss_perf);
 
 			patch_branch_site(&patch__itlbmiss_exit_1, target, 0);
-#ifndef CONFIG_PIN_TLB_TEXT
-			patch_branch_site(&patch__itlbmiss_exit_2, target, 0);
-#endif
 		}
 		val = itlb_miss_counter;
 		break;
@@ -111,8 +108,6 @@ static int mpc8xx_pmu_add(struct perf_event *event, int flags)
 			unsigned long target = patch_site_addr(&patch__dtlbmiss_perf);
 
 			patch_branch_site(&patch__dtlbmiss_exit_1, target, 0);
-			patch_branch_site(&patch__dtlbmiss_exit_2, target, 0);
-			patch_branch_site(&patch__dtlbmiss_exit_3, target, 0);
 		}
 		val = dtlb_miss_counter;
 		break;
@@ -175,9 +170,6 @@ static void mpc8xx_pmu_del(struct perf_event *event, int flags)
 					    __PPC_SPR(SPRN_SPRG_SCRATCH0));
 
 			patch_instruction_site(&patch__itlbmiss_exit_1, insn);
-#ifndef CONFIG_PIN_TLB_TEXT
-			patch_instruction_site(&patch__itlbmiss_exit_2, insn);
-#endif
 		}
 		break;
 	case PERF_8xx_ID_DTLB_LOAD_MISS:
@@ -187,8 +179,6 @@ static void mpc8xx_pmu_del(struct perf_event *event, int flags)
 					    __PPC_SPR(SPRN_DAR));
 
 			patch_instruction_site(&patch__dtlbmiss_exit_1, insn);
-			patch_instruction_site(&patch__dtlbmiss_exit_2, insn);
-			patch_instruction_site(&patch__dtlbmiss_exit_3, insn);
 		}
 		break;
 	}
Signature · 1 line
2.25.0
#39 lore raw

PATCH v4 35/45 powerpc/8xx: Move DTLB perf handling closer.

In reply to Christophe Leroy

Now that space have been freed next to the DTLB miss handler, it's associated DTLB perf handling can be brought back in the same place.

---
 arch/powerpc/kernel/head_8xx.S | 23 +++++++++++------------
 1 file changed, 11 insertions(+), 12 deletions(-)
arch/powerpc/kernel/head_8xx.S +11 -12
index fb5d17187772..9f3f7f3d03a7 100644
@@ -344,6 +344,17 @@ DataStoreTLBMiss:
 	rfi
 	patch_site	0b, patch__dtlbmiss_exit_1
 
+#ifdef CONFIG_PERF_EVENTS
+	patch_site	0f, patch__dtlbmiss_perf
+0:	lwz	r10, (dtlb_miss_counter - PAGE_OFFSET)@l(0)
+	addi	r10, r10, 1
+	stw	r10, (dtlb_miss_counter - PAGE_OFFSET)@l(0)
+	mfspr	r10, SPRN_DAR
+	mtspr	SPRN_DAR, r11	/* Tag DAR */
+	mfspr	r11, SPRN_M_TW
+	rfi
+#endif
+
 /* This is an instruction TLB error on the MPC8xx.  This could be due
  * to many reasons, such as executing guarded memory or illegal instruction
  * addresses.  There is nothing to do but handle a big time error fault.
@@ -390,18 +401,6 @@ DARFixed:/* Return from dcbx instruction bug workaround */
 	/* 0x300 is DataAccess exception, needed by bad_page_fault() */
 	EXC_XFER_LITE(0x300, handle_page_fault)
 
-/* Called from DataStoreTLBMiss when perf TLB misses events are activated */
-#ifdef CONFIG_PERF_EVENTS
-	patch_site	0f, patch__dtlbmiss_perf
-0:	lwz	r10, (dtlb_miss_counter - PAGE_OFFSET)@l(0)
-	addi	r10, r10, 1
-	stw	r10, (dtlb_miss_counter - PAGE_OFFSET)@l(0)
-	mfspr	r10, SPRN_DAR
-	mtspr	SPRN_DAR, r11	/* Tag DAR */
-	mfspr	r11, SPRN_M_TW
-	rfi
-#endif
-
 stack_overflow:
 	vmap_stack_overflow_exception
 
Signature · 1 line
2.25.0
#40 lore raw

PATCH v4 36/45 powerpc/mm: Don't be too strict with _etext alignment on PPC32

In reply to Christophe Leroy

Similar to PPC64, accept to map RO data as ROX as a trade off between between security and memory usage.

Having RO data executable is not a high risk as RO data can't be modified to forge an exploit.

---
 arch/powerpc/Kconfig              | 26 --------------------------
 arch/powerpc/kernel/vmlinux.lds.S |  3 +--
 2 files changed, 1 insertion(+), 28 deletions(-)
arch/powerpc/Kconfig +0 -26
index 1d4ef4f27dec..d147d379b1b9 100644
@@ -778,32 +778,6 @@ config THREAD_SHIFT
 	  Used to define the stack size. The default is almost always what you
 	  want. Only change this if you know what you are doing.
 
-config ETEXT_SHIFT_BOOL
-	bool "Set custom etext alignment" if STRICT_KERNEL_RWX && \
-					     (PPC_BOOK3S_32 || PPC_8xx)
-	depends on ADVANCED_OPTIONS
-	help
-	  This option allows you to set the kernel end of text alignment. When
-	  RAM is mapped by blocks, the alignment needs to fit the size and
-	  number of possible blocks. The default should be OK for most configs.
-
-	  Say N here unless you know what you are doing.
-
-config ETEXT_SHIFT
-	int "_etext shift" if ETEXT_SHIFT_BOOL
-	range 17 28 if STRICT_KERNEL_RWX && PPC_BOOK3S_32
-	range 19 23 if STRICT_KERNEL_RWX && PPC_8xx
-	default 17 if STRICT_KERNEL_RWX && PPC_BOOK3S_32
-	default 19 if STRICT_KERNEL_RWX && PPC_8xx
-	default PPC_PAGE_SHIFT
-	help
-	  On Book3S 32 (603+), IBATs are used to map kernel text.
-	  Smaller is the alignment, greater is the number of necessary IBATs.
-
-	  On 8xx, large pages (512kb or 8M) are used to map kernel linear
-	  memory. Aligning to 8M reduces TLB misses as only 8M pages are used
-	  in that case.
-
 config DATA_SHIFT_BOOL
 	bool "Set custom data alignment" if STRICT_KERNEL_RWX && \
 					    (PPC_BOOK3S_32 || PPC_8xx)
arch/powerpc/kernel/vmlinux.lds.S +1 -2
index 31a0f201fb6f..54f23205c2b9 100644
@@ -15,7 +15,6 @@
 #include <asm/thread_info.h>
 
 #define STRICT_ALIGN_SIZE	(1 << CONFIG_DATA_SHIFT)
-#define ETEXT_ALIGN_SIZE	(1 << CONFIG_ETEXT_SHIFT)
 
 ENTRY(_stext)
 
@@ -116,7 +115,7 @@ SECTIONS
 
 	} :text
 
-	. = ALIGN(ETEXT_ALIGN_SIZE);
+	. = ALIGN(PAGE_SIZE);
 	_etext = .;
 	PROVIDE32 (etext = .);
 
Signature · 1 line
2.25.0
#41 lore raw

PATCH v4 37/45 powerpc/8xx: Refactor kernel address boundary comparison

In reply to Christophe Leroy

Now that linear and IMMR dedicated TLB handling is gone, kernel boundary address comparison is similar in ITLB miss handler and in DTLB miss handler.

Create a macro named compare_to_kernel_boundary.

When TASK_SIZE is strictly below 0x80000000 and PAGE_OFFSET is above 0x80000000, it is enough to compare to 0x8000000, and this can be done with a single instruction.

Using not. instruction, we get to use 'blt' conditional branch as when doing a regular comparison:

0x00000000 <= addr <= 0x7fffffff ==>
0xffffffff >= NOT(addr) >= 0x80000000
The above test corresponds to a 'blt'

Otherwise, do a regular comparison using two instructions.

---
 arch/powerpc/kernel/head_8xx.S | 22 ++++++++--------------
 1 file changed, 8 insertions(+), 14 deletions(-)
arch/powerpc/kernel/head_8xx.S +8 -14
index 9f3f7f3d03a7..9a117b9f0998 100644
@@ -32,10 +32,15 @@
 
 #include "head_32.h"
 
+.macro compare_to_kernel_boundary scratch, addr
 #if CONFIG_TASK_SIZE <= 0x80000000 && CONFIG_PAGE_OFFSET >= 0x80000000
 /* By simply checking Address >= 0x80000000, we know if its a kernel address */
-#define SIMPLE_KERNEL_ADDRESS		1
+	not.	\scratch, \addr
+#else
+	rlwinm	\scratch, \addr, 16, 0xfff8
+	cmpli	cr0, \scratch, PAGE_OFFSET@h
 #endif
+.endm
 
 /*
  * We need an ITLB miss handler for kernel addresses if:
@@ -209,20 +214,11 @@ InstructionTLBMiss:
 	mtspr	SPRN_MD_EPN, r10
 #ifdef ITLB_MISS_KERNEL
 	mfcr	r11
-#if defined(SIMPLE_KERNEL_ADDRESS)
-	cmpi	cr0, r10, 0	/* Address >= 0x80000000 */
-#else
-	rlwinm	r10, r10, 16, 0xfff8
-	cmpli	cr0, r10, PAGE_OFFSET@h
-#endif
+	compare_to_kernel_boundary r10, r10
 #endif
 	mfspr	r10, SPRN_M_TWB	/* Get level 1 table */
 #ifdef ITLB_MISS_KERNEL
-#if defined(SIMPLE_KERNEL_ADDRESS)
-	bge+	3f
-#else
 	blt+	3f
-#endif
 	rlwinm	r10, r10, 0, 20, 31
 	oris	r10, r10, (swapper_pg_dir - PAGE_OFFSET)@ha
 3:
@@ -288,9 +284,7 @@ DataStoreTLBMiss:
 	 * kernel page tables.
 	 */
 	mfspr	r10, SPRN_MD_EPN
-	rlwinm	r10, r10, 16, 0xfff8
-	cmpli	cr0, r10, PAGE_OFFSET@h
-
+	compare_to_kernel_boundary r10, r10
 	mfspr	r10, SPRN_M_TWB	/* Get level 1 table */
 	blt+	3f
 	rlwinm	r10, r10, 0, 20, 31
Signature · 1 line
2.25.0
#42 lore raw

PATCH v4 38/45 powerpc/8xx: Add a function to early map kernel via huge pages

In reply to Christophe Leroy

Add a function to early map kernel memory using huge pages.

For 512k pages, just use standard page table and map in using 512k pages.

For 8M pages, create a hugepd table and populate the two PGD entries with it.

This function can only be used to create page tables at startup. Once the regular SLAB allocation functions replace memblock functions, this function cannot allocate new pages anymore. However it can still update existing mappings with new protections.

hugepd_none() macro is moved into asm/hugetlb.h to be usable outside of mm/hugetlbpage.c

early_pte_alloc_kernel() is made visible.

_PAGE_HUGE flag is now displayed by ptdump.

---
v2: Select CONFIG_HUGETLBFS instead of CONFIG_HUGETLB_PAGE which leads to linktime failure

---
 .../include/asm/nohash/32/hugetlb-8xx.h       |  5 ++
 arch/powerpc/include/asm/pgtable.h            |  2 +
 arch/powerpc/mm/nohash/8xx.c                  | 52 +++++++++++++++++++
 arch/powerpc/mm/pgtable_32.c                  |  2 +-
 arch/powerpc/mm/ptdump/8xx.c                  |  5 ++
 arch/powerpc/platforms/Kconfig.cputype        |  1 +
 6 files changed, 66 insertions(+), 1 deletion(-)
arch/powerpc/include/asm/nohash/32/hugetlb-8xx.h +5 -0
index 1c7d4693a78e..e752a5807a59 100644
@@ -35,6 +35,11 @@ static inline void hugepd_populate(hugepd_t *hpdp, pte_t *new, unsigned int pshi
 	*hpdp = __hugepd(__pa(new) | _PMD_USER | _PMD_PRESENT | _PMD_PAGE_8M);
 }
 
+static inline void hugepd_populate_kernel(hugepd_t *hpdp, pte_t *new, unsigned int pshift)
+{
+	*hpdp = __hugepd(__pa(new) | _PMD_PRESENT | _PMD_PAGE_8M);
+}
+
 static inline int check_and_get_huge_psize(int shift)
 {
 	return shift_to_mmu_psize(shift);
arch/powerpc/include/asm/pgtable.h +2 -0
index b1f1d5339735..961895be932a 100644
@@ -107,6 +107,8 @@ unsigned long vmalloc_to_phys(void *vmalloc_addr);
 
 void pgtable_cache_add(unsigned int shift);
 
+pte_t *early_pte_alloc_kernel(pmd_t *pmdp, unsigned long va);
+
 #if defined(CONFIG_STRICT_KERNEL_RWX) || defined(CONFIG_PPC32)
 void mark_initmem_nx(void);
 #else
arch/powerpc/mm/nohash/8xx.c +52 -0

67 lines not on this page · raw message

arch/powerpc/mm/pgtable_32.c +1 -1
index bd0cb6e3573e..05902bbff8d6 100644
@@ -61,7 +61,7 @@ static void __init *early_alloc_pgtable(unsigned long size)
 	return ptr;
 }
 
-static pte_t __init *early_pte_alloc_kernel(pmd_t *pmdp, unsigned long va)
+pte_t __init *early_pte_alloc_kernel(pmd_t *pmdp, unsigned long va)
 {
 	if (pmd_none(*pmdp)) {
 		pte_t *ptep = early_alloc_pgtable(PTE_FRAG_SIZE);
arch/powerpc/mm/ptdump/8xx.c +5 -0
index a3169677dced..b3185b32793d 100644
@@ -11,6 +11,11 @@
 
 static const struct flag_info flag_array[] = {
 	{
+		.mask	= _PAGE_HUGE,
+		.val	= _PAGE_HUGE,
+		.set	= "h",
+		.clear	= " ",
+	}, {
 		.mask	= _PAGE_RO | _PAGE_NA,
 		.val	= 0,
 		.set	= "rw",
arch/powerpc/platforms/Kconfig.cputype +1 -0
index 5774a55a9c58..e3fb0ef5129f 100644
@@ -56,6 +56,7 @@ config PPC_8xx
 	select PPC_HAVE_KUEP
 	select PPC_HAVE_KUAP
 	select HAVE_ARCH_VMAP_STACK
+	select HUGETLBFS
 
 config 40x
 	bool "AMCC 40x"
Signature · 1 line
2.25.0
#43 lore raw

PATCH v4 39/45 powerpc/8xx: Map IMMR with a huge page

In reply to Christophe Leroy

Map the IMMR area with a single 512k huge page.

---
 arch/powerpc/mm/nohash/8xx.c | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)
arch/powerpc/mm/nohash/8xx.c +2 -6
index 72fb75f2a5f1..f8fff1fa72e3 100644
@@ -118,17 +118,13 @@ static bool immr_is_mapped __initdata;
 
 void __init mmu_mapin_immr(void)
 {
-	unsigned long p = PHYS_IMMR_BASE;
-	unsigned long v = VIRT_IMMR_BASE;
-	int offset;
-
 	if (immr_is_mapped)
 		return;
 
 	immr_is_mapped = true;
 
-	for (offset = 0; offset < IMMR_SIZE; offset += PAGE_SIZE)
-		map_kernel_page(v + offset, p + offset, PAGE_KERNEL_NCG);
+	__early_map_kernel_hugepage(VIRT_IMMR_BASE, PHYS_IMMR_BASE,
+				    PAGE_KERNEL_NCG, MMU_PAGE_512K, true);
 }
 
 unsigned long __init mmu_mapin_ram(unsigned long base, unsigned long top)
Signature · 1 line
2.25.0
#44 lore raw

PATCH v4 40/45 powerpc/8xx: Map linear memory with huge pages

In reply to Christophe Leroy

Map linear memory space with 512k and 8M pages whenever possible.

Three mappings are performed:
- One for kernel text
- One for RO data
- One for the rest

Separating the mappings is done to be able to update the protection later when using STRICT_KERNEL_RWX.

The ITLB miss handler now need to also handle huge TLBs unless kernel text in pinned.

---
 arch/powerpc/kernel/head_8xx.S |  4 +--
 arch/powerpc/mm/nohash/8xx.c   | 50 +++++++++++++++++++++++++++++++++-
 2 files changed, 51 insertions(+), 3 deletions(-)
arch/powerpc/kernel/head_8xx.S +2 -2
index 9a117b9f0998..abb71fad7d6a 100644
@@ -224,7 +224,7 @@ InstructionTLBMiss:
 3:
 	mtcr	r11
 #endif
-#ifdef CONFIG_HUGETLBFS
+#if defined(CONFIG_HUGETLBFS) || !defined(CONFIG_PIN_TLB_TEXT)
 	lwz	r11, (swapper_pg_dir-PAGE_OFFSET)@l(r10)	/* Get level 1 entry */
 	mtspr	SPRN_MD_TWC, r11
 #else
@@ -234,7 +234,7 @@ InstructionTLBMiss:
 #endif
 	mfspr	r10, SPRN_MD_TWC
 	lwz	r10, 0(r10)	/* Get the pte */
-#ifdef CONFIG_HUGETLBFS
+#if defined(CONFIG_HUGETLBFS) || !defined(CONFIG_PIN_TLB_TEXT)
 	rlwimi	r11, r10, 32 - 9, _PMD_PAGE_512K
 	mtspr	SPRN_MI_TWC, r11
 #endif
arch/powerpc/mm/nohash/8xx.c +49 -1

69 lines not on this page · raw message

Signature · 1 line
2.25.0
#45 lore raw

PATCH v4 41/45 powerpc/8xx: Allow STRICT_KERNEL_RwX with pinned TLB

In reply to Christophe Leroy

Pinned TLB are 8M. Now that there is no strict boundary anymore between text and RO data, it is possible to use 8M pinned executable TLB that covers both text and RO data.

When PIN_TLB_DATA or PIN_TLB_TEXT is selected, enforce 8M RW data alignment and allow STRICT_KERNEL_RWX.

---
v2: Use the new function that sets all pinned TLBs at once.

---
 arch/powerpc/Kconfig               | 8 +++++---
 arch/powerpc/mm/nohash/8xx.c       | 9 +++++++--
 arch/powerpc/platforms/8xx/Kconfig | 2 +-
 3 files changed, 13 insertions(+), 6 deletions(-)
arch/powerpc/Kconfig +5 -3
index d147d379b1b9..f5e82629e2cd 100644
@@ -779,9 +779,10 @@ config THREAD_SHIFT
 	  want. Only change this if you know what you are doing.
 
 config DATA_SHIFT_BOOL
-	bool "Set custom data alignment" if STRICT_KERNEL_RWX && \
-					    (PPC_BOOK3S_32 || PPC_8xx)
+	bool "Set custom data alignment"
 	depends on ADVANCED_OPTIONS
+	depends on STRICT_KERNEL_RWX
+	depends on PPC_BOOK3S_32 || (PPC_8xx && !PIN_TLB_DATA && !PIN_TLB_TEXT)
 	help
 	  This option allows you to set the kernel data alignment. When
 	  RAM is mapped by blocks, the alignment needs to fit the size and
@@ -803,7 +804,8 @@ config DATA_SHIFT
 
 	  On 8xx, large pages (512kb or 8M) are used to map kernel linear
 	  memory. Aligning to 8M reduces TLB misses as only 8M pages are used
-	  in that case.
+	  in that case. If PIN_TLB is selected, it must be aligned to 8M as
+	  8M pages will be pinned.
 
 config FORCE_MAX_ZONEORDER
 	int "Maximum zone order"
arch/powerpc/mm/nohash/8xx.c +7 -2
index ec3ef75895d8..d8697f535c3e 100644
@@ -127,8 +127,8 @@ void __init mmu_mapin_immr(void)
 				    PAGE_KERNEL_NCG, MMU_PAGE_512K, true);
 }
 
-static void __init mmu_mapin_ram_chunk(unsigned long offset, unsigned long top,
-				       pgprot_t prot, bool new)
+static void mmu_mapin_ram_chunk(unsigned long offset, unsigned long top,
+				pgprot_t prot, bool new)
 {
 	unsigned long v = PAGE_OFFSET + offset;
 	unsigned long p = offset;
@@ -181,6 +181,9 @@ void mmu_mark_initmem_nx(void)
 
 	mmu_mapin_ram_chunk(0, boundary, PAGE_KERNEL_TEXT, false);
 	mmu_mapin_ram_chunk(boundary, einittext8, PAGE_KERNEL, false);
+
+	if (IS_ENABLED(CONFIG_PIN_TLB_TEXT))
+		mmu_pin_tlb(block_mapped_ram, false);
 }
 
 #ifdef CONFIG_STRICT_KERNEL_RWX
@@ -189,6 +192,8 @@ void mmu_mark_rodata_ro(void)
 	unsigned long sinittext = __pa(_sinittext);
 
 	mmu_mapin_ram_chunk(0, sinittext, PAGE_KERNEL_ROX, false);
+	if (IS_ENABLED(CONFIG_PIN_TLB_DATA))
+		mmu_pin_tlb(block_mapped_ram, true);
 }
 #endif
 
arch/powerpc/platforms/8xx/Kconfig +1 -1
index 04ea1a8a0bdc..05669f2fadce 100644
@@ -167,7 +167,7 @@ menu "8xx advanced setup"
 
 config PIN_TLB
 	bool "Pinned Kernel TLBs"
-	depends on ADVANCED_OPTIONS && !DEBUG_PAGEALLOC && !STRICT_KERNEL_RWX
+	depends on ADVANCED_OPTIONS && !DEBUG_PAGEALLOC
 	help
 	  On the 8xx, we have 32 instruction TLBs and 32 data TLBs. In each
 	  table 4 TLBs can be pinned.
Signature · 1 line
2.25.0
#46 lore raw

PATCH v4 42/45 powerpc/8xx: Allow large TLBs with DEBUG_PAGEALLOC

In reply to Christophe Leroy

DEBUG_PAGEALLOC only manages RW data.

Text and RO data can still be mapped with hugepages and pinned TLB.

In order to map with hugepages, also enforce a 512kB data alignment minimum. That's a trade-off between size of speed, taking into account that DEBUG_PAGEALLOC is a debug option. Anyway the alignment is still tunable.

We also allow tuning of alignment for book3s to limit the complexity of the test in Kconfig that will anyway disappear in the following patches once DEBUG_PAGEALLOC is handled together with BATs.

---
 arch/powerpc/Kconfig               | 11 +++++++----
 arch/powerpc/mm/init_32.c          |  5 ++++-
 arch/powerpc/mm/nohash/8xx.c       | 11 ++++++++---
 arch/powerpc/platforms/8xx/Kconfig |  2 +-
 4 files changed, 20 insertions(+), 9 deletions(-)
arch/powerpc/Kconfig +7 -4
index f5e82629e2cd..fcb0a9ae9872 100644
@@ -781,8 +781,9 @@ config THREAD_SHIFT
 config DATA_SHIFT_BOOL
 	bool "Set custom data alignment"
 	depends on ADVANCED_OPTIONS
-	depends on STRICT_KERNEL_RWX
-	depends on PPC_BOOK3S_32 || (PPC_8xx && !PIN_TLB_DATA && !PIN_TLB_TEXT)
+	depends on STRICT_KERNEL_RWX || DEBUG_PAGEALLOC
+	depends on PPC_BOOK3S_32 || (PPC_8xx && !PIN_TLB_DATA && \
+				     (!PIN_TLB_TEXT || !STRICT_KERNEL_RWX))
 	help
 	  This option allows you to set the kernel data alignment. When
 	  RAM is mapped by blocks, the alignment needs to fit the size and
@@ -793,10 +794,12 @@ config DATA_SHIFT_BOOL
 config DATA_SHIFT
 	int "Data shift" if DATA_SHIFT_BOOL
 	default 24 if STRICT_KERNEL_RWX && PPC64
-	range 17 28 if STRICT_KERNEL_RWX && PPC_BOOK3S_32
-	range 19 23 if STRICT_KERNEL_RWX && PPC_8xx
+	range 17 28 if (STRICT_KERNEL_RWX || DEBUG_PAGEALLOC) && PPC_BOOK3S_32
+	range 19 23 if (STRICT_KERNEL_RWX || DEBUG_PAGEALLOC) && PPC_8xx
 	default 22 if STRICT_KERNEL_RWX && PPC_BOOK3S_32
 	default 23 if STRICT_KERNEL_RWX && PPC_8xx
+	default 23 if DEBUG_PAGEALLOC && PPC_8xx && PIN_TLB_DATA
+	default 19 if DEBUG_PAGEALLOC && PPC_8xx
 	default PPC_PAGE_SHIFT
 	help
 	  On Book3S 32 (603+), DBATs are used to map kernel text and rodata RO.
arch/powerpc/mm/init_32.c +4 -1
index a6991ef8727d..8977a7c2543d 100644
@@ -96,11 +96,14 @@ static void __init MMU_setup(void)
 	if (strstr(boot_command_line, "noltlbs")) {
 		__map_without_ltlbs = 1;
 	}
+	if (IS_ENABLED(CONFIG_PPC_8xx))
+		return;
+
 	if (debug_pagealloc_enabled()) {
 		__map_without_bats = 1;
 		__map_without_ltlbs = 1;
 	}
-	if (strict_kernel_rwx_enabled() && !IS_ENABLED(CONFIG_PPC_8xx))
+	if (strict_kernel_rwx_enabled())
 		__map_without_ltlbs = 1;
 }
 
arch/powerpc/mm/nohash/8xx.c +8 -3
index d8697f535c3e..286441bbbe49 100644
@@ -150,7 +150,8 @@ unsigned long __init mmu_mapin_ram(unsigned long base, unsigned long top)
 {
 	unsigned long etext8 = ALIGN(__pa(_etext), SZ_8M);
 	unsigned long sinittext = __pa(_sinittext);
-	unsigned long boundary = strict_kernel_rwx_enabled() ? sinittext : etext8;
+	bool strict_boundary = strict_kernel_rwx_enabled() || debug_pagealloc_enabled();
+	unsigned long boundary = strict_boundary ? sinittext : etext8;
 	unsigned long einittext8 = ALIGN(__pa(_einittext), SZ_8M);
 
 	WARN_ON(top < einittext8);
@@ -161,8 +162,12 @@ unsigned long __init mmu_mapin_ram(unsigned long base, unsigned long top)
 		return 0;
 
 	mmu_mapin_ram_chunk(0, boundary, PAGE_KERNEL_TEXT, true);
-	mmu_mapin_ram_chunk(boundary, einittext8, PAGE_KERNEL_TEXT, true);
-	mmu_mapin_ram_chunk(einittext8, top, PAGE_KERNEL, true);
+	if (debug_pagealloc_enabled()) {
+		top = boundary;
+	} else {
+		mmu_mapin_ram_chunk(boundary, einittext8, PAGE_KERNEL_TEXT, true);
+		mmu_mapin_ram_chunk(einittext8, top, PAGE_KERNEL, true);
+	}
 
 	if (top > SZ_32M)
 		memblock_set_current_limit(top);
arch/powerpc/platforms/8xx/Kconfig +1 -1
index 05669f2fadce..abb2b45b2789 100644
@@ -167,7 +167,7 @@ menu "8xx advanced setup"
 
 config PIN_TLB
 	bool "Pinned Kernel TLBs"
-	depends on ADVANCED_OPTIONS && !DEBUG_PAGEALLOC
+	depends on ADVANCED_OPTIONS
 	help
 	  On the 8xx, we have 32 instruction TLBs and 32 data TLBs. In each
 	  table 4 TLBs can be pinned.
Signature · 1 line
2.25.0
#47 lore raw

PATCH v4 43/45 powerpc/8xx: Implement dedicated kasan_init_region()

In reply to Christophe Leroy

Implement a kasan_init_region() dedicated to 8xx that allocates KASAN regions using huge pages.

---
 arch/powerpc/mm/kasan/8xx.c    | 74 ++++++++++++++++++++++++++++++++++
 arch/powerpc/mm/kasan/Makefile |  1 +
 2 files changed, 75 insertions(+)
 create mode 100644 arch/powerpc/mm/kasan/8xx.c
arch/powerpc/mm/kasan/8xx.c new file +74 -0
new file mode 100644
index 000000000000..db4ef44af22f
@@ -0,0 +1,74 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#define DISABLE_BRANCH_PROFILING
+
+#include <linux/kasan.h>
+#include <linux/memblock.h>
+#include <linux/hugetlb.h>
+#include <asm/pgalloc.h>
+
+static int __init
+kasan_init_shadow_8M(unsigned long k_start, unsigned long k_end, void *block)
+{
+	pmd_t *pmd = pmd_ptr_k(k_start);
+	unsigned long k_cur, k_next;
+
+	for (k_cur = k_start; k_cur != k_end; k_cur = k_next, pmd += 2, block += SZ_8M) {
+		pte_basic_t *new;
+
+		k_next = pgd_addr_end(k_cur, k_end);
+		k_next = pgd_addr_end(k_next, k_end);
+		if ((void *)pmd_page_vaddr(*pmd) != kasan_early_shadow_pte)
+			continue;
+
+		new = memblock_alloc(sizeof(pte_basic_t), SZ_4K);
+		if (!new)
+			return -ENOMEM;
+
+		*new = pte_val(pte_mkhuge(pfn_pte(PHYS_PFN(__pa(block)), PAGE_KERNEL)));
+
+		hugepd_populate_kernel((hugepd_t *)pmd, (pte_t *)new, PAGE_SHIFT_8M);
+		hugepd_populate_kernel((hugepd_t *)pmd + 1, (pte_t *)new, PAGE_SHIFT_8M);
+	}
+	return 0;
+}
+
+int __init kasan_init_region(void *start, size_t size)
+{
+	unsigned long k_start = (unsigned long)kasan_mem_to_shadow(start);
+	unsigned long k_end = (unsigned long)kasan_mem_to_shadow(start + size);
+	unsigned long k_cur;
+	int ret;
+	void *block;
+
+	block = memblock_alloc(k_end - k_start, SZ_8M);
+	if (!block)
+		return -ENOMEM;
+
+	if (IS_ALIGNED(k_start, SZ_8M)) {
+		kasan_init_shadow_8M(k_start, ALIGN_DOWN(k_end, SZ_8M), block);
+		k_cur = ALIGN_DOWN(k_end, SZ_8M);
+		if (k_cur == k_end)
+			goto finish;
+	} else {
+		k_cur = k_start;
+	}
+
+	ret = kasan_init_shadow_page_tables(k_start, k_end);
+	if (ret)
+		return ret;
+
+	for (; k_cur < k_end; k_cur += PAGE_SIZE) {
+		pmd_t *pmd = pmd_ptr_k(k_cur);
+		void *va = block + k_cur - k_start;
+		pte_t pte = pfn_pte(PHYS_PFN(__pa(va)), PAGE_KERNEL);
+
+		if (k_cur < ALIGN_DOWN(k_end, SZ_512K))
+			pte = pte_mkhuge(pte);
+
+		__set_pte_at(&init_mm, k_cur, pte_offset_kernel(pmd, k_cur), pte, 0);
+	}
+finish:
+	flush_tlb_kernel_range(k_start, k_end);
+	return 0;
+}
arch/powerpc/mm/kasan/Makefile +1 -0
index 6577897673dd..440038ea79f1 100644
@@ -3,3 +3,4 @@
 KASAN_SANITIZE := n
 
 obj-$(CONFIG_PPC32)           += kasan_init_32.o
+obj-$(CONFIG_PPC_8xx)		+= 8xx.o
Signature · 1 line
2.25.0
#48 lore raw

PATCH v4 44/45 powerpc/32s: Allow mapping with BATs with DEBUG_PAGEALLOC

In reply to Christophe Leroy

DEBUG_PAGEALLOC only manages RW data.

Text and RO data can still be mapped with BATs.

In order to map with BATs, also enforce data alignment. Set by default to 256M which is a good compromise for keeping enough BATs for also KASAN and IMMR.

---
 arch/powerpc/Kconfig           | 1 +
 arch/powerpc/mm/book3s32/mmu.c | 6 ++++++
 arch/powerpc/mm/init_32.c      | 5 ++---
 3 files changed, 9 insertions(+), 3 deletions(-)
arch/powerpc/Kconfig +1 -0
index fcb0a9ae9872..752deddc9ed9 100644
@@ -797,6 +797,7 @@ config DATA_SHIFT
 	range 17 28 if (STRICT_KERNEL_RWX || DEBUG_PAGEALLOC) && PPC_BOOK3S_32
 	range 19 23 if (STRICT_KERNEL_RWX || DEBUG_PAGEALLOC) && PPC_8xx
 	default 22 if STRICT_KERNEL_RWX && PPC_BOOK3S_32
+	default 18 if DEBUG_PAGEALLOC && PPC_BOOK3S_32
 	default 23 if STRICT_KERNEL_RWX && PPC_8xx
 	default 23 if DEBUG_PAGEALLOC && PPC_8xx && PIN_TLB_DATA
 	default 19 if DEBUG_PAGEALLOC && PPC_8xx
arch/powerpc/mm/book3s32/mmu.c +6 -0
index a9b2cbc74797..a6dcc708eee3 100644
@@ -170,6 +170,12 @@ unsigned long __init mmu_mapin_ram(unsigned long base, unsigned long top)
 		pr_debug("RAM mapped without BATs\n");
 		return base;
 	}
+	if (debug_pagealloc_enabled()) {
+		if (base >= border)
+			return base;
+		if (top >= border)
+			top = border;
+	}
 
 	if (!strict_kernel_rwx_enabled() || base >= border || top <= border)
 		return __mmu_mapin_ram(base, top);
arch/powerpc/mm/init_32.c +2 -3
index 8977a7c2543d..36c39bd37256 100644
@@ -99,10 +99,9 @@ static void __init MMU_setup(void)
 	if (IS_ENABLED(CONFIG_PPC_8xx))
 		return;
 
-	if (debug_pagealloc_enabled()) {
-		__map_without_bats = 1;
+	if (debug_pagealloc_enabled())
 		__map_without_ltlbs = 1;
-	}
+
 	if (strict_kernel_rwx_enabled())
 		__map_without_ltlbs = 1;
 }
Signature · 1 line
2.25.0
#49 lore raw

PATCH v4 45/45 powerpc/32s: Implement dedicated kasan_init_region()

In reply to Christophe Leroy

Implement a kasan_init_region() dedicated to book3s/32 that allocates KASAN regions using BATs.

---
 arch/powerpc/include/asm/kasan.h      |  1 +
 arch/powerpc/mm/kasan/Makefile        |  1 +
 arch/powerpc/mm/kasan/book3s_32.c     | 57 +++++++++++++++++++++++++++
 arch/powerpc/mm/kasan/kasan_init_32.c |  2 +-
 4 files changed, 60 insertions(+), 1 deletion(-)
 create mode 100644 arch/powerpc/mm/kasan/book3s_32.c
arch/powerpc/include/asm/kasan.h +1 -0
index 107a24c3f7b3..be85c7005fb1 100644
@@ -34,6 +34,7 @@ static inline void kasan_init(void) { }
 static inline void kasan_late_init(void) { }
 #endif
 
+void kasan_update_early_region(unsigned long k_start, unsigned long k_end, pte_t pte);
 int kasan_init_shadow_page_tables(unsigned long k_start, unsigned long k_end);
 int kasan_init_region(void *start, size_t size);
 
arch/powerpc/mm/kasan/Makefile +1 -0
index 440038ea79f1..bb1a5408b86b 100644
@@ -4,3 +4,4 @@ KASAN_SANITIZE := n
 
 obj-$(CONFIG_PPC32)           += kasan_init_32.o
 obj-$(CONFIG_PPC_8xx)		+= 8xx.o
+obj-$(CONFIG_PPC_BOOK3S_32)	+= book3s_32.o
arch/powerpc/mm/kasan/book3s_32.c new file +57 -0

57 lines not on this page · raw message

arch/powerpc/mm/kasan/kasan_init_32.c +1 -1
index 76d418af4ce8..c42085801c04 100644
@@ -79,7 +79,7 @@ int __init __weak kasan_init_region(void *start, size_t size)
 	return 0;
 }
 
-static void __init
+void __init
 kasan_update_early_region(unsigned long k_start, unsigned long k_end, pte_t pte)
 {
 	unsigned long k_cur;
Signature · 1 line
2.25.0
#50 lore raw
In reply to Christophe Leroy
Quoted 9 lines · Christophe Leroy

The main purpose of this big series is to:
- reorganise huge page handling to avoid using mm_slices.
- use huge pages to map kernel memory on the 8xx.

The 8xx supports 4 page sizes: 4k, 16k, 512k and 8M.
It uses 2 Level page tables, PGD having 1024 entries, each entry covering 4M address space. Then each page table has 1024 entries.

[...]

Patches 1-6 and 9-45 applied to powerpc/next.

[01/45] powerpc/kasan: Fix error detection on memory allocation

        https://git.kernel.org/powerpc/c/d132443a73d7a131775df46f33000f67ed92de1e
[02/45] powerpc/kasan: Fix issues by lowering KASAN_SHADOW_END
        https://git.kernel.org/powerpc/c/3a66a24f6060e6775f8c02ac52329ea0152d7e58
[03/45] powerpc/kasan: Fix shadow pages allocation failure
        https://git.kernel.org/powerpc/c/d2a91cef9bbdeb87b7449fdab1a6be6000930210
[04/45] powerpc/kasan: Remove unnecessary page table locking
        https://git.kernel.org/powerpc/c/7c31c05e00fc5ff2067332c5f80e525573e7269c
[05/45] powerpc/kasan: Refactor update of early shadow mappings
        https://git.kernel.org/powerpc/c/7dec42ab57f2f59feba82abf0353164479bfde4c
[06/45] powerpc/kasan: Declare kasan_init_region() weak
        https://git.kernel.org/powerpc/c/ec97d022f621c6c850aec46d8818b49c6aae95ad
[09/45] powerpc/ptdump: Add _PAGE_COHERENT flag
        https://git.kernel.org/powerpc/c/3af4786eb429b2df76cbd7ce3bae21467ac3e4fb
[10/45] powerpc/ptdump: Display size of BATs
        https://git.kernel.org/powerpc/c/6b30830e2003d9d77696084ebe2fc19dbe7d6f70
[11/45] powerpc/ptdump: Standardise display of BAT flags
        https://git.kernel.org/powerpc/c/8961a2a5353cca5451f648f4838cd848a3b2354c
[12/45] powerpc/ptdump: Properly handle non standard page size
        https://git.kernel.org/powerpc/c/b00ff6d8c1c3898b0f768cbb38ef722d25bd2f39
[13/45] powerpc/ptdump: Handle hugepd at PGD level
        https://git.kernel.org/powerpc/c/6b789a26d7da2e0256d199da980369ef8fb49ec6
[14/45] powerpc/32s: Don't warn when mapping RO data ROX.
        https://git.kernel.org/powerpc/c/4b19f96a81bceaf0bcf44d79c0855c61158065ec
[15/45] powerpc/mm: Allocate static page tables for fixmap
        https://git.kernel.org/powerpc/c/925ac141d106b55acbe112a9272f970631a3c082
[16/45] powerpc/mm: Fix conditions to perform MMU specific management by blocks on PPC32.
        https://git.kernel.org/powerpc/c/4e3319c23a66dabfd6c35f4d2633d64d99b68096
[17/45] powerpc/mm: PTE_ATOMIC_UPDATES is only for 40x
        https://git.kernel.org/powerpc/c/fadaac67c9007cad9fc485e36dcc54460d6d5886
[18/45] powerpc/mm: Refactor pte_update() on nohash/32
        https://git.kernel.org/powerpc/c/2db99aeb63dd6e8808dc054d181c4d0e8645bbe0
[19/45] powerpc/mm: Refactor pte_update() on book3s/32
        https://git.kernel.org/powerpc/c/1c1bf294882bd12669e39ccd7680c4ce34b7c15c
[20/45] powerpc/mm: Standardise __ptep_test_and_clear_young() params between PPC32 and PPC64
        https://git.kernel.org/powerpc/c/c7fa77016eb6093df38fdabdb7a89bb9617e7185
[21/45] powerpc/mm: Standardise pte_update() prototype between PPC32 and PPC64
        https://git.kernel.org/powerpc/c/06f52524870122fb43b214d27e8f4546da36f8ba
[22/45] powerpc/mm: Create a dedicated pte_update() for 8xx
        https://git.kernel.org/powerpc/c/6ad41bfbc907be0cd414f09fa5382d2133376595
[23/45] powerpc/mm: Reduce hugepd size for 8M hugepages on 8xx
        https://git.kernel.org/powerpc/c/b12c07a4bb064c0a8db7554557b89d40f57c936f
[24/45] powerpc/8xx: Drop CONFIG_8xx_COPYBACK option
        https://git.kernel.org/powerpc/c/d3efcd38c0b99162d889e36a30425345a18edb33
[25/45] powerpc/8xx: Prepare handlers for _PAGE_HUGE for 512k pages.
        https://git.kernel.org/powerpc/c/a891c43b97d315ee5f9fe8e797d3d48fc351e053
[26/45] powerpc/8xx: Manage 512k huge pages as standard pages.
        https://git.kernel.org/powerpc/c/b250c8c08c79d1eb5354c7eaa84b7505f5f2d921
[27/45] powerpc/8xx: Only 8M pages are hugepte pages now
        https://git.kernel.org/powerpc/c/d4870b89acd7c362ded08f9295e8d143cf7e0024
[28/45] powerpc/8xx: MM_SLICE is not needed anymore
        https://git.kernel.org/powerpc/c/555904d07eef3a2e5fc458419edf6174362c4ddd
[29/45] powerpc/8xx: Move PPC_PIN_TLB options into 8xx Kconfig
        https://git.kernel.org/powerpc/c/5d4656696c30cef56b2ab506b203533c818af04d
[30/45] powerpc/8xx: Add function to set pinned TLBs
        https://git.kernel.org/powerpc/c/f76c8f6d257cefda60221c83af7f97d9f74cb3ce
[31/45] powerpc/8xx: Don't set IMMR map anymore at boot
        https://git.kernel.org/powerpc/c/136a9a0f74d2e0d9de5515190fe80344b86b45cf
[32/45] powerpc/8xx: Always pin TLBs at startup.
        https://git.kernel.org/powerpc/c/684c1664e0de63398aceb748343541b48d398710
[33/45] powerpc/8xx: Drop special handling of Linear and IMMR mappings in I/D TLB handlers
        https://git.kernel.org/powerpc/c/400dc0f86102d2ad11d3601f1948fbb02e926431
[34/45] powerpc/8xx: Remove now unused TLB miss functions
        https://git.kernel.org/powerpc/c/1251288e64ba44969e1c4d59e5ee88a6e873447b
[35/45] powerpc/8xx: Move DTLB perf handling closer.
        https://git.kernel.org/powerpc/c/0c8c2c9c201b44eed6c10d7c5c8d25fe5aab87ce
[36/45] powerpc/mm: Don't be too strict with _etext alignment on PPC32
        https://git.kernel.org/powerpc/c/a0591b60eef965f7f5255ad4696bbba9af4b43d0
[37/45] powerpc/8xx: Refactor kernel address boundary comparison
        https://git.kernel.org/powerpc/c/c8bef10a9f17b2b9549e37878b2bcd48039c136b
[38/45] powerpc/8xx: Add a function to early map kernel via huge pages
        https://git.kernel.org/powerpc/c/34536d78068318def0a370462cbc3319e1ca9014
[39/45] powerpc/8xx: Map IMMR with a huge page
        https://git.kernel.org/powerpc/c/a623bb5861dc442dc8de9edc9b3116f8b7c235c4
[40/45] powerpc/8xx: Map linear memory with huge pages
        https://git.kernel.org/powerpc/c/cf209951fa7f2e7a8ec92f45f27ea11bc024bbfc
[41/45] powerpc/8xx: Allow STRICT_KERNEL_RwX with pinned TLB
        https://git.kernel.org/powerpc/c/da1adea07576722da4597b0df7d00931f0203229
[42/45] powerpc/8xx: Allow large TLBs with DEBUG_PAGEALLOC
        https://git.kernel.org/powerpc/c/fcdafd10a363cf3278ce29c6c9a92930380c6cd8
[43/45] powerpc/8xx: Implement dedicated kasan_init_region()
        https://git.kernel.org/powerpc/c/a2feeb2c2ecbd9c9206d66f238ca710b760c9ef5
[44/45] powerpc/32s: Allow mapping with BATs with DEBUG_PAGEALLOC
        https://git.kernel.org/powerpc/c/2b279c0348af62f42be346c1ea6d70bac98df0f9
[45/45] powerpc/32s: Implement dedicated kasan_init_region()
        https://git.kernel.org/powerpc/c/7974c4732642f710b5111165ae1f7f7fed822282

cheers