hwmod and PER going idle before WFI
Hi Paul,
In working with the UART conversion to hwmod, I noticed something I don't see when not using hwmod for managing the UARTs.
Namely, in the idle path for PER we do disable the PER UART (via omap_uart_prepare_for_idle(2)) and then the GPIO context is saved via omap3_per_save_context();
When switching to use omap_hwmod, I noticed via crashes and then via lauterbach that as soon as UART3 clocks are disabled, PER goes idle. This causes the subsequent GPIO context save to fault since PER has gone idle.
I seem to remember having a similar problem before when the problem was in the management of autodeps cause by a mis-merge.
The patch below is a hack/workaround that just moves the UART idle after the GPIO context save because I haven't found the root cause yet.
Any ideas what might be happening here?
Kevin
commit 5f3cbd67a54ae8b8cecbbd9ec3f55ffe07625e88
Author: Kevin Hilman <[email protected]> Date: Mon Nov 23 11:05:02 2009 -0800
temp: OMAP3: PM: GPIO: disable PER UART after GPIO save
FIXME: GPIO core needs to use clock API to prevent this.
When PER UARTs are disabled in idle path and no GPIOs are in use, the PER block may go idle. This causes the GPIO context save that happens right after UART disabling to fail with data aborts when accessing the GPIO regs in PER.
arch/arm/mach-omap2/pm34xx.c +1 -1
@@ -398,7 +398,6 @@ void omap_sram_idle(void) per_next_state =pwrdm_read_next_pwrst (per_pwrdm); core_next_state =pwrdm_read_next_pwrst (core_pwrdm);if (per_next_state <PWRDM_POWER_ON ) { -omap_uart_prepare_idle (2 );omap2_gpio_prepare_for_idle (per_next_state);if (per_next_state ==PWRDM_POWER_OFF ) {if (core_next_state ==PWRDM_POWER_ON ) {
@@ -408,6 +407,7 @@ void omap_sram_idle(void) }else omap3_per_save_context (); } +omap_uart_prepare_idle (2 ); }if (pwrdm_read_pwrst (cam_pwrdm) ==PWRDM_POWER_ON )
Hi Kevin,
Quoted 17 lines
From: [email protected] [mailto:linux-omap- [email protected]] On Behalf Of Kevin Hilman
Hi Paul,
In working with the UART conversion to hwmod, I noticed something I don't see when not using hwmod for managing the UARTs.
Namely, in the idle path for PER we do disable the PER UART (via
omap_uart_prepare_for_idle(2)) and then the GPIO context is saved viaomap3_per_save_context();When switching to use
omap_hwmod, I noticed via crashes and then via lauterbach that as soon as UART3 clocks are disabled, PER goes idle. This causes the subsequent GPIO context save to fault since PER has gone idle.
Quoted 7 lines
I seem to remember having a similar problem before when the problem was in the management of autodeps cause by a mis-merge.
The patch below is a hack/workaround that just moves the UART idle after the GPIO context save because I haven't found the root cause yet.
Any ideas what might be happening here?
This is probably due to the PER HW supervised mode and the fact that there is no sleep dependency by default between MPU and PER or between CORE and PER.
As soon as the latest peripherals inside the PER power domain is going to idle, the clock domain and thus the power domain can transition to the next power state, even if the CPU is running. It can by avoided by enabling the dependency but then you will prevent the PER to go to OFF mode even if not used.
What was changed to trigger that behavior now?
Regards,
Benoit
Quoted 37 lines
Kevin
commit
5f3cbd67a54ae8b8cecbbd9ec3f55ffe07625e88Author: Kevin Hilman <[email protected]> Date: Mon Nov 23 11:05:02 2009 -0800temp: OMAP3: PM: GPIO: disable PER UART after GPIO save
FIXME: GPIO core needs to use clock API to prevent this.
When PER UARTs are disabled in idle path and no GPIOs are in use, the PER block may go idle. This causes the GPIO context save that happens right after UART disabling to fail with data aborts when accessing the GPIO regs in PER.
arch/arm/mach-omap2/pm34xx.c +1
-2@@ -398,7 +398,6 @@ void omap_sram_idle(void) per_next_state =pwrdm_read_next_pwrst (per_pwrdm); core_next_state =pwrdm_read_next_pwrst (core_pwrdm);if (per_next_state <PWRDM_POWER_ON ) { -omap_uart_prepare_idle (2 );omap2_gpio_prepare_for_idle (per_next_state);if (per_next_state ==PWRDM_POWER_OFF ) {if (core_next_state ==PWRDM_POWER_ON ) {@@ -408,6 +407,7 @@ void omap_sram_idle(void) }else omap3_per_save_context (); } +omap_uart_prepare_idle (2 ); }if (pwrdm_read_pwrst (cam_pwrdm) ==PWRDM_POWER_ON ) --
Quoted 3 lines
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Texas Instruments France SA, 821 Avenue Jack Kilby, 06270 Villeneuve Loubet. 036 420 040 R.C.S Antibes. Capital de EUR 753.920
Quoted 25 lines · Benoit
Hi Kevin,
Quoted 23 lines
From: [email protected] [mailto:linux-omap- [email protected]] On Behalf Of Kevin Hilman
Hi Paul,
In working with the UART conversion to hwmod, I noticed something I don't see when not using hwmod for managing the UARTs.
Namely, in the idle path for PER we do disable the PER UART (via
omap_uart_prepare_for_idle(2)) and then the GPIO context is saved viaomap3_per_save_context();When switching to use
omap_hwmod, I noticed via crashes and then via lauterbach that as soon as UART3 clocks are disabled, PER goes idle. This causes the subsequent GPIO context save to fault since PER has gone idle.I seem to remember having a similar problem before when the problem was in the management of autodeps cause by a mis-merge.
The patch below is a hack/workaround that just moves the UART idle after the GPIO context save because I haven't found the root cause yet.
Quoted 8 lines
Quoted 1 line
Any ideas what might be happening here?
This is probably due to the PER HW supervised mode and the fact that there is no sleep dependency by default between MPU and PER or between CORE and PER.
As soon as the latest peripherals inside the PER power domain is going to idle, the clock domain and thus the power domain can transition to the next power state, even if the CPU is running. It can by avoided by enabling the dependency but then you will prevent the PER to go to OFF mode even if not used.What was changed to trigger that behavior now?
The primary change is using the omap_device API for managing UART PM in mach-omap2/serial.c instead of directly using clock API.
I'll be posting the UART patches shortly.
Kevin