Skip to contentSkip to conversation

OMAP: Serial: Add omap-serial driver with platform support

PATCH Superseded Govindraj.R 2 participants 2 messages Sep 22, 2010 TTY layer and serial drivers

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover OMAP: Serial: Add omap-serial driver with platform support

This patch series adds a serial driver to handle uarts on omap platforms. Currenlty omap-uarts are handled with 8250 driver, since updating this driver with omap specific features will over load
the 8250 driver with all omap-specific data thus a new driver is added to configure and support features like
dma, h/w, s/w flowcontrol for omap-uarts.
Also the patch series updates various low level platform specific serial data to support omap-uarts with hwmod framework and adds support for uart4 on OMAP3630.

v1 to v2 changes:
----------------
1) Incorporate timeout check
http://www.mail-archive.com/linux-omap at vger.kernel.org/msg35106.html
2) Add wk_st, padconf etc for uart4
http://www.mail-archive.com/linux-omap at vger.kernel.org/msg35105.html

Benoit Cousson (1):
OMAP4: UART: Add uart1-4 hwmods data for omap4

Govindraj.R (8):
OMAP2: UART: remove set_uart_globals.
OMAP clock: Add uart4_ick/fck definitions for 3630
OMAP3: PRCM: Consider UART4 for 3630 chip in prcm_setup_regs
OMAP3: PM: Add prepare idle and resume idle call for uart4
OMAP3: serial: Fix uart4 handling for 3630
serial: Add OMAP high-speed UART driver
OMAP: SERIAL: Enable omap-serial driver in Kconfig.
OMAP3: SERIAL: Initialize all omap-uarts for zoom boards

Kevin Hilman (4):
OMAP2/3: UART: add omap_hwmod data for UARTs 1-4
OMAP: UART: omap_device converions, remove implicit 8520 assumptions
OMAP: UART: don't do automatic bus-level suspend/resume
OMAP: UART: use non-locking versions of hwmod enable/idle functions

 arch/arm/mach-omap2/Kconfig                   |   11 +-
 arch/arm/mach-omap2/board-3630sdp.c           |    1 -
 arch/arm/mach-omap2/board-zoom-peripherals.c  |    1 +
 arch/arm/mach-omap2/clock3xxx_data.c          |   22 +
 arch/arm/mach-omap2/cm-regbits-34xx.h         |    2 +
 arch/arm/mach-omap2/omap_hwmod_2420_data.c    |  193 ++++
 arch/arm/mach-omap2/omap_hwmod_2430_data.c    |  193 ++++
 arch/arm/mach-omap2/omap_hwmod_3xxx_data.c    |  253 +++++-
 arch/arm/mach-omap2/omap_hwmod_44xx_data.c    |  235 +++++
 arch/arm/mach-omap2/pm34xx.c                  |   17 +-
 arch/arm/mach-omap2/prcm-common.h             |    5 +
 arch/arm/mach-omap2/prm-regbits-34xx.h        |    1 +
 arch/arm/mach-omap2/serial.c                  |  557 ++++++-----
 arch/arm/plat-omap/common.c                   |   16 -
 arch/arm/plat-omap/include/plat/common.h      |    1 -
 arch/arm/plat-omap/include/plat/dma.h         |    2 +
 arch/arm/plat-omap/include/plat/irqs.h        |    2 +
 arch/arm/plat-omap/include/plat/omap-serial.h |  129 +++
 drivers/serial/Kconfig                        |   27 +
 drivers/serial/Makefile                       |    1 +
 drivers/serial/omap-serial.c                  | 1332 +++++++++++++++++++++++++
 include/linux/serial_core.h                   |    3 +
 22 files changed, 2707 insertions(+), 297 deletions(-)
 create mode 100644 arch/arm/plat-omap/include/plat/omap-serial.h
 create mode 100644 drivers/serial/omap-serial.c
#1 lore raw

v2 cover OMAP: Serial: Add omap-serial driver with platform support

Quoted 10 lines · Govindraj.R

This patch series adds a serial driver to handle uarts on omap platforms. Currenlty omap-uarts are handled with 8250 driver, since updating this driver with omap specific features will over load
the 8250 driver with all omap-specific data thus a new driver is added to configure and support features like
dma, h/w, s/w flowcontrol for omap-uarts.
Also the patch series updates various low level platform specific serial data to support omap-uarts with hwmod framework and adds support for uart4 on OMAP3630.

Quoted 6 lines

v1 to v2 changes:
----------------
1) Incorporate timeout check
http://www.mail-archive.com/linux-omap at vger.kernel.org/msg35106.html
2) Add wk_st, padconf etc for uart4
http://www.mail-archive.com/linux-omap at vger.kernel.org/msg35105.html

3) All UARTs initialized for Zoom2/3

Also, please report platforms this was tested on, and what was tested. You need to validate retention and off-mode during idle and suspend, as well as enabling/disabling the UART sleep_timeout values via sysfs.

Thanks,

Kevin