Skip to contentSkip to conversation

running custom apps under uboot

U-Boot-Users himbA 3 participants 5 messages Feb 23, 2004 – Feb 24, 2004

lore
Share & tools
lore

himbA

author
#0 lore raw

hi

I would like to code standalone app under uboot that would test my eth chip.
I tried running hello_world.srec from ram location and I got 'prefetch abort' on go. My procedure follows:
tftp a0100000 hello_world.srec
go a0140004 test test2
(go a0100000 test test2)

address value for go is memory location plus offset defined in Makefile. Both go commands yield an error and reset the board.

I would like to know what file and how to modify it to get standalone programs running from memory.

regards, himba

#1 lore raw
Quoted 8 lines · In message <[email protected]> you wrote:

I would like to code standalone app under uboot that would test my eth chip.
I tried running hello_world.srec from ram location and I got 'prefetch abort' on go. My procedure follows:
tftp a0100000 hello_world.srec
go a0140004 test test2
(go a0100000 test test2)

How comes you are using 0xa0100000 as load address? Did you modify the Makefile so that this address gets used? The default value used in U-Boot for ARM systems is 0xc100000 ...

Quoted 2 lines

address value for go is memory location plus offset defined in Makefile. Both go commands yield an error and reset the board.

Try running the code under a debugger...

Best regards,

Wolfgang Denk

Signature · 3 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-4596-87  Fax: (+49)-8142-4596-88  Email: wd at denx.de
You can observe a lot just by watchin'.                  - Yogi Berra
author
#2 lore raw
Quoted 11 lines · Wolfgang Denk
Quoted 7 lines · In message <[email protected]> you wrote:

I would like to code standalone app under uboot that would test my eth chip.
I tried running hello_world.srec from ram location and I got 'prefetch abort' on go. My procedure follows:
tftp a0100000 hello_world.srec
go a0140004 test test2
(go a0100000 test test2)

Quoted 4 lines

How comes you are using 0xa0100000 as load address? Did you modify the Makefile so that this address gets used? The default value used in U-Boot for ARM systems is 0xc100000 ...

I'm trying to download hello_world.srec to the memory and run it from the memory, as i do with the kernel. I didn't change any Makefiles nor any of the sources. Was it wrong to think that I could execute an image from the memory that way ?

Quoted 7 lines
Quoted 3 lines

address value for go is memory location plus offset defined in Makefile. Both go commands yield an error and reset the board.

Try running the code under a debugger...

Yet to learn :). Going slow though.

Quoted 5 lines

Best regards,

Wolfgang Denk

rgds, himba

#3 lore raw
Quoted 5 lines · In message <[email protected]> you wrote:
Quoted 5 lines
Quoted 4 lines

tftp a0100000 hello_world.srec
go a0140004 test test2
(go a0100000 test test2)

Quoted 8 lines
Quoted 4 lines

How comes you are using 0xa0100000 as load address? Did you modify the Makefile so that this address gets used? The default value used in U-Boot for ARM systems is 0xc100000 ...

I'm trying to download hello_world.srec to the memory and run it from the memory, as i do with the kernel. I didn't change any Makefiles nor any of the sources. Was it wrong to think that I could execute an image from the memory that way ?

Standalone applications are not position-independent. They are linked for a specific address and must be loaded to and started at the correct address.

Best regards,

Wolfgang Denk

Signature · 6 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-4596-87  Fax: (+49)-8142-4596-88  Email: wd at denx.de
But it's real. And if it's real it can be affected ... we may not  be
able  to break it, but, I'll bet you credits to Navy Beans we can put
a dent in it.
	-- deSalle, "Catspaw", stardate 3018.2
#4 lore raw
In reply to himbA
Quoted 15 lines · The keyboard of himbA
Quoted 9 lines · Wolfgang Denk
Quoted 7 lines · In message <[email protected]> you wrote:

I would like to code standalone app under uboot that would test my eth chip.
I tried running hello_world.srec from ram location and I got 'prefetch abort' on go. My procedure follows:
tftp a0100000 hello_world.srec
go a0140004 test test2
(go a0100000 test test2)

Quoted 5 lines

How comes you are using 0xa0100000 as load address? Did you modify
the Makefile so that this address gets used? The default value used in U-Boot for ARM systems is 0xc100000 ...

Quoted 4 lines

I'm trying to download hello_world.srec to the memory and run it from the memory, as i do with the kernel. I didn't change any Makefiles nor any of the sources. Was it wrong to think that I could execute an image from the memory that way ?

Tftp will transfer the file byte by byte so the srec ASCII will end up in RAM - I doubt that you can run that. Try the hello_world.bin binary file intended for this purpose.

Cheers
Detlev

Signature · 4 lines
Two  monks went  fishing in an  electron river.  The first monk drew out his
network, and out flopped a hacker.  The second monk cried, "The poor hacker!
How can  it live outside of the  network?"   The first monk said,  "When you
have learned to live outside the network, then you will know."