Skip to contentSkip to conversation

pandaboard_defconfig: bump u-boot to 2015.10 and kernel to 4.3

PATCH New Sergio Prado 2 participants 2 messages Feb 9, 2016 – Feb 26, 2016

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 pandaboard_defconfig: bump u-boot to 2015.10 and kernel to 4.3

VFPv3 and NEON was enabled and a readme.txt file was added.

Fixes bug #7580.

Tested on Pandaboard ES.

---
Changes v3 -> v2:
- rebased
Changes v1 -> v2:
- Removed extra "=====" signs from readme.txt.
- Removed empty new lines from readme.txt.
- Improved script and description to format the sdcard in the readme.txt.
- Locking kernel headers version, u-boot version and kernel version being used.

---
 board/pandaboard/readme.txt  | 76 ++++++++++++++++++++++++++++++++++++++++++++
 configs/pandaboard_defconfig | 43 ++++++++++---------------
 2 files changed, 92 insertions(+), 27 deletions(-)
 create mode 100644 board/pandaboard/readme.txt
board/pandaboard/readme.txt new file +76 -0
new file mode 100644
index 000000000000..8741349d19f0
@@ -0,0 +1,76 @@
+Pandaboard
+==========
+
+This file documents the Buildroot support for the Pandaboard, a
+low-power, low-cost single-board computer development platform based
+on the Texas Instruments OMAP4 system on a chip (SoC).
+
+Configuring and building Buildroot
+----------------------------------
+
+Start from the defconfig:
+
+  $ make pandaboard_defconfig
+
+You can edit build options the usual way:
+
+  $ make menuconfig
+
+When you are happy with the setup, run:
+
+  $ make
+
+The result of the build with the default settings should be these files:
+
+  output/images
+  ??? MLO
+  ??? omap4-panda-a4.dtb
+  ??? omap4-panda.dtb
+  ??? omap4-panda-es.dtb
+  ??? rootfs.ext2
+  ??? u-boot.img
+  ??? zImage
+
+Setting up your SD card
+-----------------------
+
+*Important*: pay attention which partition you are modifying so you don't
+accidentally erase the wrong file system, e.g your host computer or your
+external storage!
+
+In the default setup you need to create two partitions on your SD card:
+a boot partition and a rootfs partition.
+
+The ROM code from OMAP processors need the SD card to be formatted with
+a special geometry in the partition table. To do that, you can use the
+shell script below (this script was extracted from
+http://elinux.org/Panda_How_to_MLO_%26_u-boot).
+
+#!/bin/sh
+DRIVE=$1
+if [ -b "$DRIVE" ] ; then
+	dd if=/dev/zero of=$DRIVE bs=1024 count=1024
+	SIZE=`fdisk -l $DRIVE | grep Disk | awk '{print $5}'`
+	echo DISK SIZE - $SIZE bytes
+	CYLINDERS=`echo $SIZE/255/63/512 | bc`
+	echo CYLINDERS - $CYLINDERS
+	{
+	echo ,9,0x0C,*
+	echo ,,,-
+	} | sfdisk -D -H 255 -S 63 -C $CYLINDERS $DRIVE
+	mkfs.vfat -F 32 -n "boot" ${DRIVE}1
+	mke2fs -j -L "rootfs" ${DRIVE}2
+fi
+
+The next step is to mount the sdcard's first partition and copy MLO
+and u-boot.img to it.
+
+  $ sudo mkdir -p /mnt/sdcard
+  $ sudo mount /dev/sdX1 /mnt/sdcard
+  $ sudo cp MLO u-boot.img /mnt/sdcard
+  $ sudo umount /mnt/sdcard
+
+The last step is to copy the rootfs image to the sdcard's second
+partition using 'dd':
+
+  $ sudo dd if=rootfs.ext2 of=/dev/sdX2 bs=1M conv=fsync
configs/pandaboard_defconfig +16 -27

53 lines not on this page · raw message

Signature · 1 line
1.9.1
#1 lore raw

PATCH v3 1/1 pandaboard_defconfig: bump u-boot to 2015.10 and kernel to 4.3

Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Sergio" == Sergio Prado <[email protected]> writes:

Hi,

Quoted 4 lines

VFPv3 and NEON was enabled and a readme.txt file was added. Fixes bug #7580.

Tested on Pandaboard ES.

Sorry for the slow response. I have now dug out my pandaboard and tested this.

configs/pandaboard_defconfig line 5

Quoted 11 lines

+++ b/configs/pandaboard_defconfig

configs/pandaboard_defconfig +3 -4
@@ -1,37 +1,26 @@
-# Architecture
 BR2_arm=y
 BR2_cortex_a9=y
-
-# system
-BR2_TARGET_GENERIC_GETTY=y
+BR2_ARM_ENABLE_NEON=y
+BR2_ARM_ENABLE_VFP=y
+BR2_ARM_EABI=y

There's afaik no reason to use the old EABI instead of EABIhf on panda (E.G. the binary gpu drivers are available in EABIhf variants as well), so I've changed that and committed to next, thanks.

I've also added extra commits to bump the u-boot and kernel versions to the latest, use ext4 instead of ext2 and generate a sdcard image using genimage.

Signature · 1 line
Bye, Peter Korsgaard