Skip to contentSkip to conversation

libarchive: make bsdtar and bsdcpio binaries configurable

PATCH New Sven Neumann 2 participants 2 messages Oct 20, 2009

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 libarchive: make bsdtar and bsdcpio binaries configurable

libarchive comes with two binaries, bsdtar and bsdcpio that used to be installed by default. This change makes this configurable with the default not to build and install the binaries.

---
 package/libarchive/Config.in     |   15 +++++++++++++++
 package/libarchive/libarchive.mk |    4 ++++
 2 files changed, 19 insertions(+), 0 deletions(-)
package/libarchive/Config.in +15 -0
index 9154861..079e0f8 100644
@@ -9,3 +9,18 @@ config BR2_PACKAGE_LIBARCHIVE
 
 comment "libarchive requires a toolchain with WCHAR support"
 	depends on !BR2_USE_WCHAR
+
+config BR2_PACKAGE_LIBARCHIVE_BSDTAR
+	bool "bsdtar"
+	depends on BR2_PACKAGE_LIBARCHIVE
+	help
+	  The 'bsdtar' program is a full-featured 'tar'
+          replacement built on libarchive.
+
+config BR2_PACKAGE_LIBARCHIVE_BSDCPIO
+	bool "bsdcpio"
+	depends on BR2_PACKAGE_LIBARCHIVE
+	help
+	  The 'bsdcpio' program is a different interface to
+          essentially the same functionality as 'bsdtar'.
+
package/libarchive/libarchive.mk +4 -0
index 472e34b..32f68f7 100644
@@ -10,4 +10,8 @@ LIBARCHIVE_LIBTOOL_PATCH = NO
 LIBARCHIVE_INSTALL_STAGING = YES
 LIBARCHIVE_INSTALL_TARGET = YES
 
+LIBARCHIVE_CONF_OPT = \
+	$(if $(BR2_PACKAGE_LIBARCHIVE_BSDTAR),--enable-bsdtar,--disable-bsdtar) \
+	$(if $(BR2_PACKAGE_LIBARCHIVE_BSDCPIO),--enable-bsdcpio,--disable-bsdcpio)
+
 $(eval $(call AUTOTARGETS,package,libarchive))
Signature · 1 line
1.6.5
#1 lore raw

PATCH 1/1 libarchive: make bsdtar and bsdcpio binaries configurable

Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Sven" == Sven Neumann <[email protected]> writes:

Sven> libarchive comes with two binaries, bsdtar and bsdcpio that used Sven> to be installed by default. This change makes this configurable Sven> with the default not to build and install the binaries. Sven> ---

 Sven>  package/libarchive/Config.in     |   15 +++++++++++++++
 Sven>  package/libarchive/libarchive.mk |    4 ++++

Sven> 2 files changed, 19 insertions(+), 0 deletions(-)

Sven> diff --git a/package/libarchive/Config.in b/package/libarchive/Config.in Sven> index 9154861..079e0f8 100644
Sven> --- a/package/libarchive/Config.in
Sven> +++ b/package/libarchive/Config.in
Sven> @@ -9,3 +9,18 @@ config BR2_PACKAGE_LIBARCHIVE

Sven> comment "libarchive requires a toolchain with WCHAR support"
Sven> depends on !BR2_USE_WCHAR
Sven> +
Sven> +config BR2_PACKAGE_LIBARCHIVE_BSDTAR
Sven> + bool "bsdtar"
Sven> + depends on BR2_PACKAGE_LIBARCHIVE
Sven> + help
Sven> + The 'bsdtar' program is a full-featured 'tar'
Sven> + replacement built on libarchive.

Indentation of 2nd line here and below is wrong - Other than that it looks good, committed.

Signature · 1 line
Bye, Peter Korsgaard