PCI: mvebu: Add support for error interrupt
Subsystems (4)
Pali Rohár
maintainercover PCI: mvebu: Add support for error interrupt
PCI mvebu error interrupt source is triggered for non-INTx event. So e.g. when AER or PME event occurs.
This patch series adds support for reporting AER and PME interrupts on Marvell PCIe Root Ports which allows use to kernel AER and PME drivers.
Without this change kernel AER and PME drivers do not work at all.
DT bindings for this support is currently provided only for Kirkwood and Dove platforms as other new mvebu SoCs requires extension to armada IRQ driver, which is currently disallowed.
Without new DTS files, pci-mvebu.c driver acts as before this change, there is no AER and PME kernel support.
I have tested this change on Armada 385 board (with additional changes to A385 DTS files and IRQ driver, not included there) and AER interrupt is delivered to kernel AER driver correctly.
Pali Rohár (4):
dt-bindings: PCI: mvebu: Update information about error interrupt
PCI: mvebu: Implement support for interrupts on emulated bridge
ARM: dts: kirkwood: Add definitions for PCIe error interrupts
ARM: dts: dove: Add definitions for PCIe error interrupts
.../devicetree/bindings/pci/mvebu-pci.txt | 1 + arch/arm/boot/dts/dove.dtsi | 8 +- arch/arm/boot/dts/kirkwood-6192.dtsi | 4 +- arch/arm/boot/dts/kirkwood-6281.dtsi | 4 +- arch/arm/boot/dts/kirkwood-6282.dtsi | 8 +- arch/arm/boot/dts/kirkwood-98dx4122.dtsi | 4 +- drivers/pci/controller/pci-mvebu.c | 256 ++++++++++++++++-- 7 files changed, 252 insertions(+), 33 deletions(-)
Signature · 1 line
2.20.1
Pali Rohár
maintainerPATCH 1/4 dt-bindings: PCI: mvebu: Update information about error interrupt
mvebu error interrupt is triggered by any non-intx event, which is mainly some pcie error.
--- Documentation/devicetree/bindings/pci/mvebu-pci.txt | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/pci/mvebu-pci.txt +1 -0
@@ -83,6 +83,7 @@ and the following optional properties: specified will default to 100ms, as required by the PCIe specification. - interrupt-names: list of interrupt names, supported are: - "intx" - interrupt line triggered by one of the legacy interrupt + - "error" - interrupt line triggered by any other event (non-intx) - interrupts or interrupts-extended: List of the interrupt sources which corresponding to the "interrupt-names". If non-empty then also additional 'interrupt-controller' subnode must be defined.
Signature · 1 line
2.20.1
Re: [PATCH 1/4] dt-bindings: PCI: mvebu: Update information about error interrupt
Quoted 7 lines · Pali Rohár
mvebu error interrupt is triggered by any non-intx event, which is mainly some pcie error.
Signed-off-by Pali Rohár <[email protected]>--- Documentation/devicetree/bindings/pci/mvebu-pci.txt | 1 + 1 file changed, 1 insertion(+)
Re: [PATCH 1/4] dt-bindings: PCI: mvebu: Update information about error interrupt
In reply to Pali RohárQuoted 4 lines · Pali Rohár
mvebu error interrupt is triggered by any non-intx event, which is mainly some pcie error.
Signed-off-by Pali Rohár <[email protected]>
Andrew
Pali Rohár
maintainerPATCH 2/4 PCI: mvebu: Implement support for interrupts on emulated bridge
In reply to Pali RohárThis adds support for PME and ERR interrupts reported by emulated bridge (for PME and AER kernel drivers) via new Root Port irq chip as these interrupts from PCIe Root Ports are handled by mvebu hardware completely separately from INTx and MSI interrupts send by real PCIe devices.
With this change, kernel PME and AER drivers start working as they can acquire required interrupt lines (provided by mvebu rp virtual irq chip).
Note that for this support, device tree files has to be properly adjusted to provide "interrupts" or "interrupts-extended" property with error interrupt source and "interrupt-names" property with "error" string.
If device tree files do not provide these properties then driver would work as before and would not provide interrupts on emulated bridge, like before.
--- drivers/pci/controller/pci-mvebu.c | 256 ++++++++++++++++++++++++++--- 1 file changed, 237 insertions(+), 19 deletions(-)
drivers/pci/controller/pci-mvebu.c +237 -19
@@ -56,8 +56,16 @@#define PCIE_CONF_DATA_OFF 0x18fc#define PCIE_INT_CAUSE_OFF 0x1900#define PCIE_INT_UNMASK_OFF 0x1910 +#define PCIE_INT_DET_COR BIT(8) +#define PCIE_INT_DET_NONFATAL BIT(9) +#define PCIE_INT_DET_FATAL BIT(10) +#define PCIE_INT_ERR_FATAL BIT(16) +#define PCIE_INT_ERR_NONFATAL BIT(17) +#define PCIE_INT_ERR_COR BIT(18)#define PCIE_INT_INTX (i) BIT(24+i)#define PCIE_INT_PM_PME BIT(28) +#define PCIE_INT_DET_MASK (PCIE_INT_DET_COR | PCIE_INT_DET_NONFATAL | PCIE_INT_DET_FATAL) +#define PCIE_INT_ERR_MASK (PCIE_INT_ERR_FATAL | PCIE_INT_ERR_NONFATAL | PCIE_INT_ERR_COR)#define PCIE_INT_ALL_MASK GENMASK(31, 0)#define PCIE_CTRL_OFF 0x1a00#define PCIE_CTRL_X1_MODE 0x0001
@@ -120,9 +128,12 @@ struct mvebu_pcie_port {struct resource regs;u8 slot_power_limit_value;u8 slot_power_limit_scale; +struct irq_domain *rp_irq_domain;struct irq_domain *intx_irq_domain;raw_spinlock_t irq_lock; +int error_irq;int intx_irq; +bool pme_pending; };static inline void mvebu_writel (struct mvebu_pcie_port *port,u32 val,u32 reg)
@@ -321,9 +332,19 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port)/* Clear all interrupt causes. */ mvebu_writel (port, ~PCIE_INT_ALL_MASK ,PCIE_INT_CAUSE_OFF ); -/* Check if "intx" interrupt was specified in DT. */ -if (port->intx_irq >0 ) -return ; +/* +* Unmask all error interrupts which are internally generated. +* They cannot be disabled by SERR# Enable bit in PCI Command register, +* see Figure 6-3: Pseudo Logic Diagram for Error Message Controls in +* PCIe base specification. +* Internally generated mvebu interrupts are reported via mvebu summary +* interrupt which requires "error" interrupt to be specified in DT. +*/ +if (port->error_irq >0 ) { + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + unmask |=PCIE_INT_DET_MASK ; +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + }/* * Fallback code when "intx" interrupt was not specified in DT:
@@ -335,10 +356,12 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port)* performance penalty as every PCIe interrupt handler needs to be * called when some interrupt is triggered. */ - unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); - unmask |=PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | -PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ); -mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); +if (port->intx_irq <=0 ) { + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + unmask |=PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ); +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + } } static struct mvebu_pcie_port *mvebu_pcie_find_port(struct mvebu_pcie *pcie,
@@ -603,11 +626,16 @@ mvebu_pci_bridge_emul_base_conf_read(struct pci_bridge_emul *bridge,case PCI_INTERRUPT_LINE : {/* * From the whole 32bit register we support reading from HW only -* one bit: PCI_BRIDGE_CTL_BUS_RESET. +* two bits: PCI_BRIDGE_CTL_BUS_RESET and PCI_BRIDGE_CTL_SERR. * Other bits are retrieved only from emulated config buffer. */ __le32 *cfgspace = (__le32 *)&bridge->conf;u32 val =le32_to_cpu (cfgspace[PCI_INTERRUPT_LINE /4 ]); +if ((mvebu_readl (port,PCIE_INT_UNMASK_OFF ) & +PCIE_INT_ERR_MASK ) ==PCIE_INT_ERR_MASK ) + val |=PCI_BRIDGE_CTL_SERR <<16 ; +else + val &= ~(PCI_BRIDGE_CTL_SERR <<16 );if (mvebu_readl (port,PCIE_CTRL_OFF ) &PCIE_CTRL_MASTER_HOT_RESET ) val |=PCI_BRIDGE_CTL_BUS_RESET <<16 ;else
@@ -675,6 +703,11 @@ mvebu_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge,break ; } +case PCI_EXP_RTCTL : + *value = (mvebu_readl (port,PCIE_INT_UNMASK_OFF ) & +PCIE_INT_PM_PME ) ?PCI_EXP_RTCTL_PMEIE :0 ; +break ; +case PCI_EXP_RTSTA : *value =mvebu_readl (port,PCIE_RC_RTSTA );break ;
@@ -780,6 +813,14 @@ mvebu_pci_bridge_emul_base_conf_write(struct pci_bridge_emul *bridge,break ;case PCI_INTERRUPT_LINE : +if ((mask & (PCI_BRIDGE_CTL_SERR <<16 )) && port->error_irq >0 ) { +u32 unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); +if (new & (PCI_BRIDGE_CTL_SERR <<16 )) + unmask |=PCIE_INT_ERR_MASK ; +else + unmask &= ~PCIE_INT_ERR_MASK ; +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + }if (mask & (PCI_BRIDGE_CTL_BUS_RESET <<16 )) {u32 ctrl =mvebu_readl (port,PCIE_CTRL_OFF );if (new & (PCI_BRIDGE_CTL_BUS_RESET <<16 ))
@@ -838,10 +879,25 @@ mvebu_pci_bridge_emul_pcie_conf_write(struct pci_bridge_emul *bridge,* PME Status bit in Root Status Register (PCIE_RC_RTSTA) * is read-only and can be cleared only by writing 0b to the * Interrupt Cause RW0C register (PCIE_INT_CAUSE_OFF). So -* clear PME via Interrupt Cause. +* clear PME via Interrupt Cause and also set port->pme_pending +* variable to false value to start processing PME interrupts +* in interrupt handler again. */ -if (new &PCI_EXP_RTSTA_PME ) +if (new &PCI_EXP_RTSTA_PME ) {mvebu_writel (port, ~PCIE_INT_PM_PME ,PCIE_INT_CAUSE_OFF ); + port->pme_pending = false; + } +break ; + +case PCI_EXP_RTCTL : +if ((mask &PCI_EXP_RTCTL_PMEIE ) && port->error_irq >0 ) { +u32 unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); +if (new &PCI_EXP_RTCTL_PMEIE ) + unmask |=PCIE_INT_PM_PME ; +else + unmask &= ~PCIE_INT_PM_PME ; +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + }break ;case PCI_EXP_DEVCTL2 :
@@ -924,6 +980,14 @@ static int mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port) bridge_flags |=PCI_BRIDGE_EMUL_NO_IO_FORWARD ; } +/* +* Interrupts on emulated bridge are supported only when "error" +* interrupt was specified in DT. Without it emulated bridge cannot +* emulate interrupts. +*/ +if (port->error_irq >0 ) + bridge->conf.intpin =PCI_INTERRUPT_INTA ; +/* * Older mvebu hardware provides PCIe Capability structure only in * version 1. New hardware provides it in version 2.
@@ -1072,6 +1136,26 @@ static const struct irq_domain_ops mvebu_pcie_intx_irq_domain_ops = { .xlate = irq_domain_xlate_onecell, }; +static struct irq_chip rp_irq_chip = { + .name ="mvebu-rp" , +}; + +static int mvebu_pcie_rp_irq_map (struct irq_domain *h, +unsigned int virq,irq_hw_number_t hwirq) +{ +struct mvebu_pcie_port *port = h->host_data; + +irq_set_chip_and_handler (virq, &rp_irq_chip, handle_simple_irq); +irq_set_chip_data (virq, port); + +return 0 ; +} + +static const struct irq_domain_ops mvebu_pcie_rp_irq_domain_ops = { + .map = mvebu_pcie_rp_irq_map, + .xlate = irq_domain_xlate_onecell, +}; +static int mvebu_pcie_init_irq_domain (struct mvebu_pcie_port *port) {struct device *dev = &port->pcie->pdev->dev;
@@ -1094,10 +1178,72 @@ static int mvebu_pcie_init_irq_domain(struct mvebu_pcie_port *port)return -ENOMEM ; } +/* +* When "error" interrupt was not specified in DT then there is no +* support for interrupts on emulated root bridge. So skip following +* initialization. +*/ +if (port->error_irq <=0 ) +return 0 ; + + port->rp_irq_domain =irq_domain_add_linear (NULL ,1 , + &mvebu_pcie_rp_irq_domain_ops, + port); +if (!port->rp_irq_domain) { +irq_domain_remove (port->intx_irq_domain); +dev_err (dev,"Failed to add Root Port IRQ domain for %s\n" , port->name); +return -ENOMEM ; + } +return 0 ; } -static irqreturn_t mvebu_pcie_irq_handler (int irq,void *arg) +static irqreturn_t mvebu_pcie_error_irq_handler (int irq,void *arg) +{ +struct mvebu_pcie_port *port = arg; +struct device *dev = &port->pcie->pdev->dev; +u32 cause, unmask, status; + + cause =mvebu_readl (port,PCIE_INT_CAUSE_OFF ); + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + status = cause & unmask; + +/* "error" interrupt handler does not process INTX interrupts */ + status &= ~(PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 )); + +/* Process PME interrupt */ +if ((status &PCIE_INT_PM_PME ) && !port->pme_pending) { +/* +* Do not clear PME interrupt bit in Cause Register as it +* invalidates also content of Root Status Register. Instead +* set port->pme_pending variable to true to indicate that +* next time PME interrupt should be ignored until variable +* is back to the false value. +*/ + port->pme_pending = true; +if (generic_handle_domain_irq (port->rp_irq_domain,0 ) == -EINVAL ) +dev_err_ratelimited (dev,"unhandled PME IRQ\n" ); + } + +/* Process ERR interrupt */ +if (status &PCIE_INT_ERR_MASK ) { +mvebu_writel (port, ~PCIE_INT_ERR_MASK ,PCIE_INT_CAUSE_OFF ); +if (generic_handle_domain_irq (port->rp_irq_domain,0 ) == -EINVAL ) +dev_err_ratelimited (dev,"unhandled ERR IRQ\n" ); + } + +/* Process local ERR interrupt */ +if (status &PCIE_INT_DET_MASK ) { +mvebu_writel (port, ~PCIE_INT_DET_MASK ,PCIE_INT_CAUSE_OFF ); +if (generic_handle_domain_irq (port->rp_irq_domain,0 ) == -EINVAL ) +dev_err_ratelimited (dev,"unhandled ERR IRQ\n" ); + } + +return status ?IRQ_HANDLED :IRQ_NONE ; +} + +static irqreturn_t mvebu_pcie_intx_irq_handler (int irq,void *arg) {struct mvebu_pcie_port *port = arg;struct device *dev = &port->pcie->pdev->dev;
@@ -1108,6 +1254,10 @@ static irqreturn_t mvebu_pcie_irq_handler(int irq, void *arg) unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); status = cause & unmask; +/* "intx" interrupt handler process only INTX interrupts */ + status &=PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ); +/* Process legacy INTx interrupts */ for (i =0 ; i <PCI_NUM_INTX ; i++) {if (!(status &PCIE_INT_INTX (i)))
@@ -1122,9 +1272,29 @@ static irqreturn_t mvebu_pcie_irq_handler(int irq, void *arg)static int mvebu_pcie_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) { -/* Interrupt support on mvebu emulated bridges is not implemented yet */ -if (dev->bus->number ==0 ) -return 0 ;/* Proper return code 0 == NO_IRQ */ +struct mvebu_pcie_port *port; +struct mvebu_pcie *pcie; + +if (dev->bus->number ==0 ) { +/* +* Each emulated root bridge for every mvebu port has its own +* Root Port irq chip and irq domain. Argument pin is the INTx +* pin (1=INTA, 2=INTB, 3=INTC, 4=INTD) and hwirq for function +* irq_create_mapping() is indexed from zero. +*/ + pcie = dev->bus->sysdata; + port =mvebu_pcie_find_port (pcie, dev->bus,PCI_DEVFN (slot,0 )); +if (!port) +return 0 ;/* Proper return code 0 == NO_IRQ */ +/* +* port->rp_irq_domain is available only when "error" interrupt +* was specified in DT. When is not available then interrupts +* for emulated root bridge are not provided. +*/ +if (port->error_irq <=0 ) +return 0 ;/* Proper return code 0 == NO_IRQ */ +return irq_create_mapping (port->rp_irq_domain, pin -1 ); + }return of_irq_parse_and_map_pci (dev, slot, pin); }
@@ -1333,6 +1503,21 @@ static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie, port->name, child); } +/* +* Old DT bindings do not contain "error" interrupt +* so do not fail probing driver when interrupt does not exist. +*/ + port->error_irq =of_irq_get_byname (child,"error" ); +if (port->error_irq == -EPROBE_DEFER ) { + ret = port->error_irq; + goto err; + } +if (port->error_irq <=0 ) { +dev_warn (dev,"%s: interrupts on Root Port are unsupported, " +"%pOF does not contain error interrupt\n" , + port->name, child); + } + reset_gpio =of_get_named_gpio_flags (child,"reset-gpios" ,0 , &flags);if (reset_gpio == -EPROBE_DEFER ) { ret = reset_gpio;
@@ -1538,7 +1723,6 @@ static int mvebu_pcie_probe(struct platform_device *pdev)for (i =0 ; i < pcie->nports; i++) {struct mvebu_pcie_port *port = &pcie->ports[i]; -int irq = port->intx_irq; child = port->dn;if (!child)
@@ -1566,7 +1750,7 @@ static int mvebu_pcie_probe(struct platform_device *pdev)continue ; } -if (irq >0 ) { +if (port->error_irq >0 || port->intx_irq >0 ) { ret =mvebu_pcie_init_irq_domain (port);if (ret) { dev_err(dev, "%s: cannot init irq domain\n",
@@ -1577,14 +1761,42 @@ static int mvebu_pcie_probe(struct platform_device *pdev)mvebu_pcie_powerdown (port);continue ; } + } + +if (port->error_irq >0 ) { + ret =devm_request_irq (dev, port->error_irq, + mvebu_pcie_error_irq_handler, +IRQF_SHARED |IRQF_NO_THREAD , + port->name, port); +if (ret) { +dev_err (dev,"%s: cannot register error interrupt handler: %d\n" , + port->name, ret); +if (port->intx_irq_domain) +irq_domain_remove (port->intx_irq_domain); +if (port->rp_irq_domain) +irq_domain_remove (port->rp_irq_domain); +pci_bridge_emul_cleanup (&port->bridge); +devm_iounmap (dev, port->base); + port->base =NULL ; +mvebu_pcie_powerdown (port); +continue ; + } + } - ret =devm_request_irq (dev, irq, mvebu_pcie_irq_handler, +if (port->intx_irq >0 ) { + ret =devm_request_irq (dev, port->intx_irq, + mvebu_pcie_intx_irq_handler,IRQF_SHARED |IRQF_NO_THREAD , port->name, port);if (ret) { -dev_err (dev,"%s: cannot register interrupt handler: %d\n" , +dev_err (dev,"%s: cannot register intx interrupt handler: %d\n" , port->name, ret); -irq_domain_remove (port->intx_irq_domain); +if (port->error_irq >0 ) +devm_free_irq (dev, port->error_irq, port); +if (port->intx_irq_domain) +irq_domain_remove (port->intx_irq_domain); +if (port->rp_irq_domain) +irq_domain_remove (port->rp_irq_domain);pci_bridge_emul_cleanup (&port->bridge);devm_iounmap (dev, port->base); port->base =NULL ;
@@ -1722,6 +1934,12 @@ static int mvebu_pcie_remove(struct platform_device *pdev) }irq_domain_remove (port->intx_irq_domain); } +if (port->rp_irq_domain) { +int virq =irq_find_mapping (port->rp_irq_domain,0 ); +if (virq >0 ) +irq_dispose_mapping (virq); +irq_domain_remove (port->rp_irq_domain); + }/* Free config space for emulated root bridge. */ pci_bridge_emul_cleanup (&port->bridge);
Signature · 1 line
2.20.1
Re: [PATCH 2/4] PCI: mvebu: Implement support for interrupts on emulated bridge
Quoted 4 lines
drivers/pci/controller/pci-mvebu.c +3
-1-static irqreturn_t mvebu_pcie_irq_handler (int irq,void *arg) +static irqreturn_t mvebu_pcie_error_irq_handler (int irq,void *arg) +{ +struct mvebu_pcie_port *port = arg;
drivers/pci/controller/pci-mvebu.c static int mvebu_pcie_init_irq_domain(struct mvebu_pcie_port *port) · line 1213
Quoted 10 lines
drivers/pci/controller/pci-mvebu.c +10
-0+struct device *dev = &port->pcie->pdev->dev; +u32 cause, unmask, status; + + cause =mvebu_readl (port,PCIE_INT_CAUSE_OFF ); + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + status = cause & unmask; + +/* "error" interrupt handler does not process INTX interrupts */ + status &= ~(PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ));
Just for my understanding...
There are two interrupts, but the status information what those interrupts actually mean are all packed into one register? I assume reading the clause register does not clear set bits? Otherwise there would be a race condition. Are these actually level interrupts, and in order to clear them you need to poke some other register?
drivers/pci/controller/pci-mvebu.c static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie, · line 1516
Quoted 11 lines
drivers/pci/controller/pci-mvebu.c +11
-0+/* +* Old DT bindings do not contain "error" interrupt +* so do not fail probing driver when interrupt does not exist. +*/ + port->error_irq =of_irq_get_byname (child,"error" ); +if (port->error_irq == -EPROBE_DEFER ) { + ret = port->error_irq; + goto err; + } +if (port->error_irq <=0 ) { + dev_warn(dev, "%s: interrupts on Root Port are unsupported, "
Maybe that should be "Error interrupts on Root..." ?
Andrew
Pali Rohár
maintainerRe: [PATCH 2/4] PCI: mvebu: Implement support for interrupts on emulated bridge
Quoted 17 lines · On Thursday 18 August 2022 21:51:21 Andrew Lunn wrote:
Quoted 4 lines
drivers/pci/controller/pci-mvebu.c +3
-1-static irqreturn_t mvebu_pcie_irq_handler (int irq,void *arg) +static irqreturn_t mvebu_pcie_error_irq_handler (int irq,void *arg) +{ +struct mvebu_pcie_port *port = arg;drivers/pci/controller/pci-mvebu.c static int mvebu_pcie_init_irq_domain(struct mvebu_pcie_port *port) · line 1213
Quoted 10 lines
drivers/pci/controller/pci-mvebu.c +10
-0+struct device *dev = &port->pcie->pdev->dev; +u32 cause, unmask, status; + + cause =mvebu_readl (port,PCIE_INT_CAUSE_OFF ); + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + status = cause & unmask; + +/* "error" interrupt handler does not process INTX interrupts */ + status &= ~(PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ));Just for my understanding...
Quoted 1 line
There are two interrupts
yes
Quoted 2 lines
but the status information what those
interrupts actually mean are all packed into one register?
yes
for masking individual interrupt events there is just one shared register for both "intx" and "error" interrupt source.
and also there is also just one shared "cause" register which says which individual interrupt events happened.
Quoted 1 line
I assume reading the clause register does not clear set bits?
yes, reading does not clear any interrupt event.
Quoted 4 lines
Otherwise there
would be a race condition.Are these actually level interrupts
yes
Quoted 1 line
and in order to clear them you need to poke some other register?
to clear individual interrupt event you have to write corresponding 1b bit into that cause register.
so if interrupts events BIT(24), BIT(16) and BIT(17) happened and BIT(24), BIT(25), BIT(26), BIT(27) and BIT(16) are unmasked then CPU receives two interrupts (one for intx:24-27 and one for err:16). kernel will call interrupt handlers for both intx and err (possible also in parallel if it unmasked on different CPUs) and each handler just clears events which process. So writing BIT(16) into cause register clears only event 16 and all other (24-27, 17) are still active. And level interrupt (the correct one intx or err) is then triggered again.
Quoted 14 lines
drivers/pci/controller/pci-mvebu.c static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie, · line 1516
Quoted 11 lines
drivers/pci/controller/pci-mvebu.c +11
-0+/* +* Old DT bindings do not contain "error" interrupt +* so do not fail probing driver when interrupt does not exist. +*/ + port->error_irq =of_irq_get_byname (child,"error" ); +if (port->error_irq == -EPROBE_DEFER ) { + ret = port->error_irq; + goto err; + } +if (port->error_irq <=0 ) { + dev_warn(dev, "%s: interrupts on Root Port are unsupported, "Maybe that should be "Error interrupts on Root..." ?
Quoted 1 line
Andrew
From PCIe Root Port point of view, it can be _any_ interrupt which can PCIe Root Port (as PCI device) reports (it does not have to be PCIe AER
- error). Without this support PCIe Root Port cannot trigger or generate any interrupt. Note that from PCIe point of view, this Marvell Root Port never generates INTx interrupt. INTx interrupts are generated only by endpoint devices. Marvell Root Port reports all events via those _custom_ Marvell interrupts triggered by "error" source. So "error" here means "Marvell error", not "PCIe error" (e.g. PCIe AER). For example also PME events are reported via this "error" source. And PME is not error.
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH 2/4] PCI: mvebu: Implement support for interrupts on emulated bridge
Quoted 49 lines · Pali Rohár
Quoted 17 lines · On Thursday 18 August 2022 21:51:21 Andrew Lunn wrote:
Quoted 4 lines
drivers/pci/controller/pci-mvebu.c +3
-1-static irqreturn_t mvebu_pcie_irq_handler (int irq,void *arg) +static irqreturn_t mvebu_pcie_error_irq_handler (int irq,void *arg) +{ +struct mvebu_pcie_port *port = arg;drivers/pci/controller/pci-mvebu.c static int mvebu_pcie_init_irq_domain(struct mvebu_pcie_port *port) · line 1213
Quoted 10 lines
drivers/pci/controller/pci-mvebu.c +10
-0+struct device *dev = &port->pcie->pdev->dev; +u32 cause, unmask, status; + + cause =mvebu_readl (port,PCIE_INT_CAUSE_OFF ); + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + status = cause & unmask; + +/* "error" interrupt handler does not process INTX interrupts */ + status &= ~(PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ));Just for my understanding...
Quoted 1 line
There are two interrupts
yes
Quoted 2 lines
but the status information what those
interrupts actually mean are all packed into one register?yes
for masking individual interrupt events there is just one shared register for both "intx" and "error" interrupt source.
and also there is also just one shared "cause" register which says which individual interrupt events happened.
Quoted 1 line
I assume reading the clause register does not clear set bits?
yes, reading does not clear any interrupt event.
Quoted 4 lines
Otherwise there
would be a race condition.Are these actually level interrupts
yes
Quoted 1 line
and in order to clear them you need to poke some other register?
to clear individual interrupt event you have to write corresponding 1b bit into that cause register.
Quoted 8 lines
so if interrupts events BIT(24), BIT(16) and BIT(17) happened and BIT(24), BIT(25), BIT(26), BIT(27) and BIT(16) are unmasked then CPU receives two interrupts (one for intx:24-27 and one for err:16). kernel will call interrupt handlers for both intx and err (possible also in parallel if it unmasked on different CPUs) and each handler just clears events which process. So writing BIT(16) into cause register clears only event 16 and all other (24-27, 17) are still active. And level interrupt (the correct one intx or err) is then triggered again.
Thanks for the explanation.
I don't know enough about PCI to be able to give a meaningful Reviewed-by, so i will leave that to the PCI maintainer. But the DT bits look good to me.
Andrew
Pali Rohár
maintainerRe: [PATCH 2/4] PCI: mvebu: Implement support for interrupts on emulated bridge
In reply to Pali RohárQuoted 12 lines · On Thursday 18 August 2022 01:00:34 Pali Rohár wrote:
This adds support for PME and ERR interrupts reported by emulated bridge (for PME and AER kernel drivers) via new Root Port irq chip as these interrupts from PCIe Root Ports are handled by mvebu hardware completely separately from INTx and MSI interrupts send by real PCIe devices.
With this change, kernel PME and AER drivers start working as they can acquire required interrupt lines (provided by mvebu rp virtual irq chip).
Note that for this support, device tree files has to be properly adjusted to provide "interrupts" or "interrupts-extended" property with error interrupt source and "interrupt-names" property with "error" string.
Quoted 5 lines
If device tree files do not provide these properties then driver would work as before and would not provide interrupts on emulated bridge, like before.
Signed-off-by Pali Rohár <[email protected]>---
Just to note that because these error interrupts are shared on some mvebu platforms, this patch depends on another patch which convert driver to devm_request_irq() and which I sent more months before:
https://lore.kernel.org/linux-pci/[email protected]/
Quoted 411 lines
drivers/pci/controller/pci-mvebu.c | 256 ++++++++++++++++++++++++++--- 1 file changed, 237 insertions(+), 19 deletions(-)drivers/pci/controller/pci-mvebu.c +237
-19@@ -56,8 +56,16 @@#define PCIE_CONF_DATA_OFF 0x18fc#define PCIE_INT_CAUSE_OFF 0x1900#define PCIE_INT_UNMASK_OFF 0x1910 +#define PCIE_INT_DET_COR BIT(8) +#define PCIE_INT_DET_NONFATAL BIT(9) +#define PCIE_INT_DET_FATAL BIT(10) +#define PCIE_INT_ERR_FATAL BIT(16) +#define PCIE_INT_ERR_NONFATAL BIT(17) +#define PCIE_INT_ERR_COR BIT(18)#define PCIE_INT_INTX (i) BIT(24+i)#define PCIE_INT_PM_PME BIT(28) +#define PCIE_INT_DET_MASK (PCIE_INT_DET_COR | PCIE_INT_DET_NONFATAL | PCIE_INT_DET_FATAL) +#define PCIE_INT_ERR_MASK (PCIE_INT_ERR_FATAL | PCIE_INT_ERR_NONFATAL | PCIE_INT_ERR_COR)#define PCIE_INT_ALL_MASK GENMASK(31, 0)#define PCIE_CTRL_OFF 0x1a00#define PCIE_CTRL_X1_MODE 0x0001@@ -120,9 +128,12 @@ struct mvebu_pcie_port {struct resource regs;u8 slot_power_limit_value;u8 slot_power_limit_scale; +struct irq_domain *rp_irq_domain;struct irq_domain *intx_irq_domain;raw_spinlock_t irq_lock; +int error_irq;int intx_irq; +bool pme_pending; };static inline void mvebu_writel (struct mvebu_pcie_port *port,u32 val,u32 reg)@@ -321,9 +332,19 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port)/* Clear all interrupt causes. */ mvebu_writel (port, ~PCIE_INT_ALL_MASK ,PCIE_INT_CAUSE_OFF ); -/* Check if "intx" interrupt was specified in DT. */ -if (port->intx_irq >0 ) -return ; +/* +* Unmask all error interrupts which are internally generated. +* They cannot be disabled by SERR# Enable bit in PCI Command register, +* see Figure 6-3: Pseudo Logic Diagram for Error Message Controls in +* PCIe base specification. +* Internally generated mvebu interrupts are reported via mvebu summary +* interrupt which requires "error" interrupt to be specified in DT. +*/ +if (port->error_irq >0 ) { + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + unmask |=PCIE_INT_DET_MASK ; +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + }/* * Fallback code when "intx" interrupt was not specified in DT: @@ -335,10 +356,12 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port)* performance penalty as every PCIe interrupt handler needs to be * called when some interrupt is triggered. */ - unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); - unmask |=PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | -PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ); -mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); +if (port->intx_irq <=0 ) { + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + unmask |=PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ); +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + } } static struct mvebu_pcie_port *mvebu_pcie_find_port(struct mvebu_pcie *pcie,@@ -603,11 +626,16 @@ mvebu_pci_bridge_emul_base_conf_read(struct pci_bridge_emul *bridge,case PCI_INTERRUPT_LINE : {/* * From the whole 32bit register we support reading from HW only -* one bit: PCI_BRIDGE_CTL_BUS_RESET. +* two bits: PCI_BRIDGE_CTL_BUS_RESET and PCI_BRIDGE_CTL_SERR. * Other bits are retrieved only from emulated config buffer. */ __le32 *cfgspace = (__le32 *)&bridge->conf;u32 val =le32_to_cpu (cfgspace[PCI_INTERRUPT_LINE /4 ]); +if ((mvebu_readl (port,PCIE_INT_UNMASK_OFF ) & +PCIE_INT_ERR_MASK ) ==PCIE_INT_ERR_MASK ) + val |=PCI_BRIDGE_CTL_SERR <<16 ; +else + val &= ~(PCI_BRIDGE_CTL_SERR <<16 );if (mvebu_readl (port,PCIE_CTRL_OFF ) &PCIE_CTRL_MASTER_HOT_RESET ) val |=PCI_BRIDGE_CTL_BUS_RESET <<16 ;else @@ -675,6 +703,11 @@ mvebu_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge,break ; } +case PCI_EXP_RTCTL : + *value = (mvebu_readl (port,PCIE_INT_UNMASK_OFF ) & +PCIE_INT_PM_PME ) ?PCI_EXP_RTCTL_PMEIE :0 ; +break ; +case PCI_EXP_RTSTA : *value =mvebu_readl (port,PCIE_RC_RTSTA );break ;@@ -780,6 +813,14 @@ mvebu_pci_bridge_emul_base_conf_write(struct pci_bridge_emul *bridge,break ;case PCI_INTERRUPT_LINE : +if ((mask & (PCI_BRIDGE_CTL_SERR <<16 )) && port->error_irq >0 ) { +u32 unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); +if (new & (PCI_BRIDGE_CTL_SERR <<16 )) + unmask |=PCIE_INT_ERR_MASK ; +else + unmask &= ~PCIE_INT_ERR_MASK ; +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + }if (mask & (PCI_BRIDGE_CTL_BUS_RESET <<16 )) {u32 ctrl =mvebu_readl (port,PCIE_CTRL_OFF );if (new & (PCI_BRIDGE_CTL_BUS_RESET <<16 ))@@ -838,10 +879,25 @@ mvebu_pci_bridge_emul_pcie_conf_write(struct pci_bridge_emul *bridge,* PME Status bit in Root Status Register (PCIE_RC_RTSTA) * is read-only and can be cleared only by writing 0b to the * Interrupt Cause RW0C register (PCIE_INT_CAUSE_OFF). So -* clear PME via Interrupt Cause. +* clear PME via Interrupt Cause and also set port->pme_pending +* variable to false value to start processing PME interrupts +* in interrupt handler again. */ -if (new &PCI_EXP_RTSTA_PME ) +if (new &PCI_EXP_RTSTA_PME ) {mvebu_writel (port, ~PCIE_INT_PM_PME ,PCIE_INT_CAUSE_OFF ); + port->pme_pending = false; + } +break ; + +case PCI_EXP_RTCTL : +if ((mask &PCI_EXP_RTCTL_PMEIE ) && port->error_irq >0 ) { +u32 unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); +if (new &PCI_EXP_RTCTL_PMEIE ) + unmask |=PCIE_INT_PM_PME ; +else + unmask &= ~PCIE_INT_PM_PME ; +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + }break ;case PCI_EXP_DEVCTL2 :@@ -924,6 +980,14 @@ static int mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port) bridge_flags |=PCI_BRIDGE_EMUL_NO_IO_FORWARD ; } +/* +* Interrupts on emulated bridge are supported only when "error" +* interrupt was specified in DT. Without it emulated bridge cannot +* emulate interrupts. +*/ +if (port->error_irq >0 ) + bridge->conf.intpin =PCI_INTERRUPT_INTA ; +/* * Older mvebu hardware provides PCIe Capability structure only in * version 1. New hardware provides it in version 2. @@ -1072,6 +1136,26 @@ static const struct irq_domain_ops mvebu_pcie_intx_irq_domain_ops = { .xlate = irq_domain_xlate_onecell, }; +static struct irq_chip rp_irq_chip = { + .name ="mvebu-rp" , +}; + +static int mvebu_pcie_rp_irq_map (struct irq_domain *h, +unsigned int virq,irq_hw_number_t hwirq) +{ +struct mvebu_pcie_port *port = h->host_data; + +irq_set_chip_and_handler (virq, &rp_irq_chip, handle_simple_irq); +irq_set_chip_data (virq, port); + +return 0 ; +} + +static const struct irq_domain_ops mvebu_pcie_rp_irq_domain_ops = { + .map = mvebu_pcie_rp_irq_map, + .xlate = irq_domain_xlate_onecell, +}; +static int mvebu_pcie_init_irq_domain (struct mvebu_pcie_port *port) {struct device *dev = &port->pcie->pdev->dev;@@ -1094,10 +1178,72 @@ static int mvebu_pcie_init_irq_domain(struct mvebu_pcie_port *port)return -ENOMEM ; } +/* +* When "error" interrupt was not specified in DT then there is no +* support for interrupts on emulated root bridge. So skip following +* initialization. +*/ +if (port->error_irq <=0 ) +return 0 ; + + port->rp_irq_domain =irq_domain_add_linear (NULL ,1 , + &mvebu_pcie_rp_irq_domain_ops, + port); +if (!port->rp_irq_domain) { +irq_domain_remove (port->intx_irq_domain); +dev_err (dev,"Failed to add Root Port IRQ domain for %s\n" , port->name); +return -ENOMEM ; + } +return 0 ; } -static irqreturn_t mvebu_pcie_irq_handler (int irq,void *arg) +static irqreturn_t mvebu_pcie_error_irq_handler (int irq,void *arg) +{ +struct mvebu_pcie_port *port = arg; +struct device *dev = &port->pcie->pdev->dev; +u32 cause, unmask, status; + + cause =mvebu_readl (port,PCIE_INT_CAUSE_OFF ); + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + status = cause & unmask; + +/* "error" interrupt handler does not process INTX interrupts */ + status &= ~(PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 )); + +/* Process PME interrupt */ +if ((status &PCIE_INT_PM_PME ) && !port->pme_pending) { +/* +* Do not clear PME interrupt bit in Cause Register as it +* invalidates also content of Root Status Register. Instead +* set port->pme_pending variable to true to indicate that +* next time PME interrupt should be ignored until variable +* is back to the false value. +*/ + port->pme_pending = true; +if (generic_handle_domain_irq (port->rp_irq_domain,0 ) == -EINVAL ) +dev_err_ratelimited (dev,"unhandled PME IRQ\n" ); + } + +/* Process ERR interrupt */ +if (status &PCIE_INT_ERR_MASK ) { +mvebu_writel (port, ~PCIE_INT_ERR_MASK ,PCIE_INT_CAUSE_OFF ); +if (generic_handle_domain_irq (port->rp_irq_domain,0 ) == -EINVAL ) +dev_err_ratelimited (dev,"unhandled ERR IRQ\n" ); + } + +/* Process local ERR interrupt */ +if (status &PCIE_INT_DET_MASK ) { +mvebu_writel (port, ~PCIE_INT_DET_MASK ,PCIE_INT_CAUSE_OFF ); +if (generic_handle_domain_irq (port->rp_irq_domain,0 ) == -EINVAL ) +dev_err_ratelimited (dev,"unhandled ERR IRQ\n" ); + } + +return status ?IRQ_HANDLED :IRQ_NONE ; +} + +static irqreturn_t mvebu_pcie_intx_irq_handler (int irq,void *arg) {struct mvebu_pcie_port *port = arg;struct device *dev = &port->pcie->pdev->dev;@@ -1108,6 +1254,10 @@ static irqreturn_t mvebu_pcie_irq_handler(int irq, void *arg) unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); status = cause & unmask; +/* "intx" interrupt handler process only INTX interrupts */ + status &=PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ); +/* Process legacy INTx interrupts */ for (i =0 ; i <PCI_NUM_INTX ; i++) {if (!(status &PCIE_INT_INTX (i)))@@ -1122,9 +1272,29 @@ static irqreturn_t mvebu_pcie_irq_handler(int irq, void *arg)static int mvebu_pcie_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) { -/* Interrupt support on mvebu emulated bridges is not implemented yet */ -if (dev->bus->number ==0 ) -return 0 ;/* Proper return code 0 == NO_IRQ */ +struct mvebu_pcie_port *port; +struct mvebu_pcie *pcie; + +if (dev->bus->number ==0 ) { +/* +* Each emulated root bridge for every mvebu port has its own +* Root Port irq chip and irq domain. Argument pin is the INTx +* pin (1=INTA, 2=INTB, 3=INTC, 4=INTD) and hwirq for function +* irq_create_mapping() is indexed from zero. +*/ + pcie = dev->bus->sysdata; + port =mvebu_pcie_find_port (pcie, dev->bus,PCI_DEVFN (slot,0 )); +if (!port) +return 0 ;/* Proper return code 0 == NO_IRQ */ +/* +* port->rp_irq_domain is available only when "error" interrupt +* was specified in DT. When is not available then interrupts +* for emulated root bridge are not provided. +*/ +if (port->error_irq <=0 ) +return 0 ;/* Proper return code 0 == NO_IRQ */ +return irq_create_mapping (port->rp_irq_domain, pin -1 ); + }return of_irq_parse_and_map_pci (dev, slot, pin); }@@ -1333,6 +1503,21 @@ static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie, port->name, child); } +/* +* Old DT bindings do not contain "error" interrupt +* so do not fail probing driver when interrupt does not exist. +*/ + port->error_irq =of_irq_get_byname (child,"error" ); +if (port->error_irq == -EPROBE_DEFER ) { + ret = port->error_irq; + goto err; + } +if (port->error_irq <=0 ) { +dev_warn (dev,"%s: interrupts on Root Port are unsupported, " +"%pOF does not contain error interrupt\n" , + port->name, child); + } + reset_gpio =of_get_named_gpio_flags (child,"reset-gpios" ,0 , &flags);if (reset_gpio == -EPROBE_DEFER ) { ret = reset_gpio;@@ -1538,7 +1723,6 @@ static int mvebu_pcie_probe(struct platform_device *pdev)for (i =0 ; i < pcie->nports; i++) {struct mvebu_pcie_port *port = &pcie->ports[i]; -int irq = port->intx_irq; child = port->dn;if (!child)@@ -1566,7 +1750,7 @@ static int mvebu_pcie_probe(struct platform_device *pdev)continue ; } -if (irq >0 ) { +if (port->error_irq >0 || port->intx_irq >0 ) { ret =mvebu_pcie_init_irq_domain (port);if (ret) { dev_err(dev, "%s: cannot init irq domain\n",@@ -1577,14 +1761,42 @@ static int mvebu_pcie_probe(struct platform_device *pdev)mvebu_pcie_powerdown (port);continue ; } + } + +if (port->error_irq >0 ) { + ret =devm_request_irq (dev, port->error_irq, + mvebu_pcie_error_irq_handler, +IRQF_SHARED |IRQF_NO_THREAD , + port->name, port); +if (ret) { +dev_err (dev,"%s: cannot register error interrupt handler: %d\n" , + port->name, ret); +if (port->intx_irq_domain) +irq_domain_remove (port->intx_irq_domain); +if (port->rp_irq_domain) +irq_domain_remove (port->rp_irq_domain); +pci_bridge_emul_cleanup (&port->bridge); +devm_iounmap (dev, port->base); + port->base =NULL ; +mvebu_pcie_powerdown (port); +continue ; + } + } - ret =devm_request_irq (dev, irq, mvebu_pcie_irq_handler, +if (port->intx_irq >0 ) { + ret =devm_request_irq (dev, port->intx_irq, + mvebu_pcie_intx_irq_handler,IRQF_SHARED |IRQF_NO_THREAD , port->name, port);if (ret) { -dev_err (dev,"%s: cannot register interrupt handler: %d\n" , +dev_err (dev,"%s: cannot register intx interrupt handler: %d\n" , port->name, ret); -irq_domain_remove (port->intx_irq_domain); +if (port->error_irq >0 ) +devm_free_irq (dev, port->error_irq, port); +if (port->intx_irq_domain) +irq_domain_remove (port->intx_irq_domain); +if (port->rp_irq_domain) +irq_domain_remove (port->rp_irq_domain);pci_bridge_emul_cleanup (&port->bridge);devm_iounmap (dev, port->base); port->base =NULL ;@@ -1722,6 +1934,12 @@ static int mvebu_pcie_remove(struct platform_device *pdev) }irq_domain_remove (port->intx_irq_domain); } +if (port->rp_irq_domain) { +int virq =irq_find_mapping (port->rp_irq_domain,0 ); +if (virq >0 ) +irq_dispose_mapping (virq); +irq_domain_remove (port->rp_irq_domain); + }/* Free config space for emulated root bridge. */ pci_bridge_emul_cleanup (&port->bridge);Signature · 1 line
2.20.1
Pali Rohár
maintainerRe: [PATCH 2/4] PCI: mvebu: Implement support for interrupts on emulated bridge
Hello!
Gentle reminder for this patch. It is waiting there for more than month and other patches from this patch series were already reviewed and merged. Could you please look at it?
As stated in commit message this patch adds support for PCIe AER to pci-mvebu.c and as we know AER required for debugging any PCIe endpoint issues.
Quoted 435 lines · On Tuesday 30 August 2022 14:36:39 Pali Rohár wrote:
Quoted 12 lines · On Thursday 18 August 2022 01:00:34 Pali Rohár wrote:
This adds support for PME and ERR interrupts reported by emulated bridge (for PME and AER kernel drivers) via new Root Port irq chip as these interrupts from PCIe Root Ports are handled by mvebu hardware completely separately from INTx and MSI interrupts send by real PCIe devices.
With this change, kernel PME and AER drivers start working as they can acquire required interrupt lines (provided by mvebu rp virtual irq chip).
Note that for this support, device tree files has to be properly adjusted to provide "interrupts" or "interrupts-extended" property with error interrupt source and "interrupt-names" property with "error" string.
Quoted 5 lines
If device tree files do not provide these properties then driver would work as before and would not provide interrupts on emulated bridge, like before.
Signed-off-by Pali Rohár <[email protected]>---
Just to note that because these error interrupts are shared on some mvebu platforms, this patch depends on another patch which convert driver to
devm_request_irq()and which I sent more months before:
https://lore.kernel.org/linux-pci/[email protected]/Quoted 411 lines
drivers/pci/controller/pci-mvebu.c | 256 ++++++++++++++++++++++++++--- 1 file changed, 237 insertions(+), 19 deletions(-)drivers/pci/controller/pci-mvebu.c +237
-19@@ -56,8 +56,16 @@#define PCIE_CONF_DATA_OFF 0x18fc#define PCIE_INT_CAUSE_OFF 0x1900#define PCIE_INT_UNMASK_OFF 0x1910 +#define PCIE_INT_DET_COR BIT(8) +#define PCIE_INT_DET_NONFATAL BIT(9) +#define PCIE_INT_DET_FATAL BIT(10) +#define PCIE_INT_ERR_FATAL BIT(16) +#define PCIE_INT_ERR_NONFATAL BIT(17) +#define PCIE_INT_ERR_COR BIT(18)#define PCIE_INT_INTX (i) BIT(24+i)#define PCIE_INT_PM_PME BIT(28) +#define PCIE_INT_DET_MASK (PCIE_INT_DET_COR | PCIE_INT_DET_NONFATAL | PCIE_INT_DET_FATAL) +#define PCIE_INT_ERR_MASK (PCIE_INT_ERR_FATAL | PCIE_INT_ERR_NONFATAL | PCIE_INT_ERR_COR)#define PCIE_INT_ALL_MASK GENMASK(31, 0)#define PCIE_CTRL_OFF 0x1a00#define PCIE_CTRL_X1_MODE 0x0001@@ -120,9 +128,12 @@ struct mvebu_pcie_port {struct resource regs;u8 slot_power_limit_value;u8 slot_power_limit_scale; +struct irq_domain *rp_irq_domain;struct irq_domain *intx_irq_domain;raw_spinlock_t irq_lock; +int error_irq;int intx_irq; +bool pme_pending; };static inline void mvebu_writel (struct mvebu_pcie_port *port,u32 val,u32 reg)@@ -321,9 +332,19 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port)/* Clear all interrupt causes. */ mvebu_writel (port, ~PCIE_INT_ALL_MASK ,PCIE_INT_CAUSE_OFF ); -/* Check if "intx" interrupt was specified in DT. */ -if (port->intx_irq >0 ) -return ; +/* +* Unmask all error interrupts which are internally generated. +* They cannot be disabled by SERR# Enable bit in PCI Command register, +* see Figure 6-3: Pseudo Logic Diagram for Error Message Controls in +* PCIe base specification. +* Internally generated mvebu interrupts are reported via mvebu summary +* interrupt which requires "error" interrupt to be specified in DT. +*/ +if (port->error_irq >0 ) { + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + unmask |=PCIE_INT_DET_MASK ; +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + }/* * Fallback code when "intx" interrupt was not specified in DT: @@ -335,10 +356,12 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port)* performance penalty as every PCIe interrupt handler needs to be * called when some interrupt is triggered. */ - unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); - unmask |=PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | -PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ); -mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); +if (port->intx_irq <=0 ) { + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + unmask |=PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ); +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + } } static struct mvebu_pcie_port *mvebu_pcie_find_port(struct mvebu_pcie *pcie,@@ -603,11 +626,16 @@ mvebu_pci_bridge_emul_base_conf_read(struct pci_bridge_emul *bridge,case PCI_INTERRUPT_LINE : {/* * From the whole 32bit register we support reading from HW only -* one bit: PCI_BRIDGE_CTL_BUS_RESET. +* two bits: PCI_BRIDGE_CTL_BUS_RESET and PCI_BRIDGE_CTL_SERR. * Other bits are retrieved only from emulated config buffer. */ __le32 *cfgspace = (__le32 *)&bridge->conf;u32 val =le32_to_cpu (cfgspace[PCI_INTERRUPT_LINE /4 ]); +if ((mvebu_readl (port,PCIE_INT_UNMASK_OFF ) & +PCIE_INT_ERR_MASK ) ==PCIE_INT_ERR_MASK ) + val |=PCI_BRIDGE_CTL_SERR <<16 ; +else + val &= ~(PCI_BRIDGE_CTL_SERR <<16 );if (mvebu_readl (port,PCIE_CTRL_OFF ) &PCIE_CTRL_MASTER_HOT_RESET ) val |=PCI_BRIDGE_CTL_BUS_RESET <<16 ;else @@ -675,6 +703,11 @@ mvebu_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge,break ; } +case PCI_EXP_RTCTL : + *value = (mvebu_readl (port,PCIE_INT_UNMASK_OFF ) & +PCIE_INT_PM_PME ) ?PCI_EXP_RTCTL_PMEIE :0 ; +break ; +case PCI_EXP_RTSTA : *value =mvebu_readl (port,PCIE_RC_RTSTA );break ;@@ -780,6 +813,14 @@ mvebu_pci_bridge_emul_base_conf_write(struct pci_bridge_emul *bridge,break ;case PCI_INTERRUPT_LINE : +if ((mask & (PCI_BRIDGE_CTL_SERR <<16 )) && port->error_irq >0 ) { +u32 unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); +if (new & (PCI_BRIDGE_CTL_SERR <<16 )) + unmask |=PCIE_INT_ERR_MASK ; +else + unmask &= ~PCIE_INT_ERR_MASK ; +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + }if (mask & (PCI_BRIDGE_CTL_BUS_RESET <<16 )) {u32 ctrl =mvebu_readl (port,PCIE_CTRL_OFF );if (new & (PCI_BRIDGE_CTL_BUS_RESET <<16 ))@@ -838,10 +879,25 @@ mvebu_pci_bridge_emul_pcie_conf_write(struct pci_bridge_emul *bridge,* PME Status bit in Root Status Register (PCIE_RC_RTSTA) * is read-only and can be cleared only by writing 0b to the * Interrupt Cause RW0C register (PCIE_INT_CAUSE_OFF). So -* clear PME via Interrupt Cause. +* clear PME via Interrupt Cause and also set port->pme_pending +* variable to false value to start processing PME interrupts +* in interrupt handler again. */ -if (new &PCI_EXP_RTSTA_PME ) +if (new &PCI_EXP_RTSTA_PME ) {mvebu_writel (port, ~PCIE_INT_PM_PME ,PCIE_INT_CAUSE_OFF ); + port->pme_pending = false; + } +break ; + +case PCI_EXP_RTCTL : +if ((mask &PCI_EXP_RTCTL_PMEIE ) && port->error_irq >0 ) { +u32 unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); +if (new &PCI_EXP_RTCTL_PMEIE ) + unmask |=PCIE_INT_PM_PME ; +else + unmask &= ~PCIE_INT_PM_PME ; +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + }break ;case PCI_EXP_DEVCTL2 :@@ -924,6 +980,14 @@ static int mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port) bridge_flags |=PCI_BRIDGE_EMUL_NO_IO_FORWARD ; } +/* +* Interrupts on emulated bridge are supported only when "error" +* interrupt was specified in DT. Without it emulated bridge cannot +* emulate interrupts. +*/ +if (port->error_irq >0 ) + bridge->conf.intpin =PCI_INTERRUPT_INTA ; +/* * Older mvebu hardware provides PCIe Capability structure only in * version 1. New hardware provides it in version 2. @@ -1072,6 +1136,26 @@ static const struct irq_domain_ops mvebu_pcie_intx_irq_domain_ops = { .xlate = irq_domain_xlate_onecell, }; +static struct irq_chip rp_irq_chip = { + .name ="mvebu-rp" , +}; + +static int mvebu_pcie_rp_irq_map (struct irq_domain *h, +unsigned int virq,irq_hw_number_t hwirq) +{ +struct mvebu_pcie_port *port = h->host_data; + +irq_set_chip_and_handler (virq, &rp_irq_chip, handle_simple_irq); +irq_set_chip_data (virq, port); + +return 0 ; +} + +static const struct irq_domain_ops mvebu_pcie_rp_irq_domain_ops = { + .map = mvebu_pcie_rp_irq_map, + .xlate = irq_domain_xlate_onecell, +}; +static int mvebu_pcie_init_irq_domain (struct mvebu_pcie_port *port) {struct device *dev = &port->pcie->pdev->dev;@@ -1094,10 +1178,72 @@ static int mvebu_pcie_init_irq_domain(struct mvebu_pcie_port *port)return -ENOMEM ; } +/* +* When "error" interrupt was not specified in DT then there is no +* support for interrupts on emulated root bridge. So skip following +* initialization. +*/ +if (port->error_irq <=0 ) +return 0 ; + + port->rp_irq_domain =irq_domain_add_linear (NULL ,1 , + &mvebu_pcie_rp_irq_domain_ops, + port); +if (!port->rp_irq_domain) { +irq_domain_remove (port->intx_irq_domain); +dev_err (dev,"Failed to add Root Port IRQ domain for %s\n" , port->name); +return -ENOMEM ; + } +return 0 ; } -static irqreturn_t mvebu_pcie_irq_handler (int irq,void *arg) +static irqreturn_t mvebu_pcie_error_irq_handler (int irq,void *arg) +{ +struct mvebu_pcie_port *port = arg; +struct device *dev = &port->pcie->pdev->dev; +u32 cause, unmask, status; + + cause =mvebu_readl (port,PCIE_INT_CAUSE_OFF ); + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + status = cause & unmask; + +/* "error" interrupt handler does not process INTX interrupts */ + status &= ~(PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 )); + +/* Process PME interrupt */ +if ((status &PCIE_INT_PM_PME ) && !port->pme_pending) { +/* +* Do not clear PME interrupt bit in Cause Register as it +* invalidates also content of Root Status Register. Instead +* set port->pme_pending variable to true to indicate that +* next time PME interrupt should be ignored until variable +* is back to the false value. +*/ + port->pme_pending = true; +if (generic_handle_domain_irq (port->rp_irq_domain,0 ) == -EINVAL ) +dev_err_ratelimited (dev,"unhandled PME IRQ\n" ); + } + +/* Process ERR interrupt */ +if (status &PCIE_INT_ERR_MASK ) { +mvebu_writel (port, ~PCIE_INT_ERR_MASK ,PCIE_INT_CAUSE_OFF ); +if (generic_handle_domain_irq (port->rp_irq_domain,0 ) == -EINVAL ) +dev_err_ratelimited (dev,"unhandled ERR IRQ\n" ); + } + +/* Process local ERR interrupt */ +if (status &PCIE_INT_DET_MASK ) { +mvebu_writel (port, ~PCIE_INT_DET_MASK ,PCIE_INT_CAUSE_OFF ); +if (generic_handle_domain_irq (port->rp_irq_domain,0 ) == -EINVAL ) +dev_err_ratelimited (dev,"unhandled ERR IRQ\n" ); + } + +return status ?IRQ_HANDLED :IRQ_NONE ; +} + +static irqreturn_t mvebu_pcie_intx_irq_handler (int irq,void *arg) {struct mvebu_pcie_port *port = arg;struct device *dev = &port->pcie->pdev->dev;@@ -1108,6 +1254,10 @@ static irqreturn_t mvebu_pcie_irq_handler(int irq, void *arg) unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); status = cause & unmask; +/* "intx" interrupt handler process only INTX interrupts */ + status &=PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ); +/* Process legacy INTx interrupts */ for (i =0 ; i <PCI_NUM_INTX ; i++) {if (!(status &PCIE_INT_INTX (i)))@@ -1122,9 +1272,29 @@ static irqreturn_t mvebu_pcie_irq_handler(int irq, void *arg)static int mvebu_pcie_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) { -/* Interrupt support on mvebu emulated bridges is not implemented yet */ -if (dev->bus->number ==0 ) -return 0 ;/* Proper return code 0 == NO_IRQ */ +struct mvebu_pcie_port *port; +struct mvebu_pcie *pcie; + +if (dev->bus->number ==0 ) { +/* +* Each emulated root bridge for every mvebu port has its own +* Root Port irq chip and irq domain. Argument pin is the INTx +* pin (1=INTA, 2=INTB, 3=INTC, 4=INTD) and hwirq for function +* irq_create_mapping() is indexed from zero. +*/ + pcie = dev->bus->sysdata; + port =mvebu_pcie_find_port (pcie, dev->bus,PCI_DEVFN (slot,0 )); +if (!port) +return 0 ;/* Proper return code 0 == NO_IRQ */ +/* +* port->rp_irq_domain is available only when "error" interrupt +* was specified in DT. When is not available then interrupts +* for emulated root bridge are not provided. +*/ +if (port->error_irq <=0 ) +return 0 ;/* Proper return code 0 == NO_IRQ */ +return irq_create_mapping (port->rp_irq_domain, pin -1 ); + }return of_irq_parse_and_map_pci (dev, slot, pin); }@@ -1333,6 +1503,21 @@ static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie, port->name, child); } +/* +* Old DT bindings do not contain "error" interrupt +* so do not fail probing driver when interrupt does not exist. +*/ + port->error_irq =of_irq_get_byname (child,"error" ); +if (port->error_irq == -EPROBE_DEFER ) { + ret = port->error_irq; + goto err; + } +if (port->error_irq <=0 ) { +dev_warn (dev,"%s: interrupts on Root Port are unsupported, " +"%pOF does not contain error interrupt\n" , + port->name, child); + } + reset_gpio =of_get_named_gpio_flags (child,"reset-gpios" ,0 , &flags);if (reset_gpio == -EPROBE_DEFER ) { ret = reset_gpio;@@ -1538,7 +1723,6 @@ static int mvebu_pcie_probe(struct platform_device *pdev)for (i =0 ; i < pcie->nports; i++) {struct mvebu_pcie_port *port = &pcie->ports[i]; -int irq = port->intx_irq; child = port->dn;if (!child)@@ -1566,7 +1750,7 @@ static int mvebu_pcie_probe(struct platform_device *pdev)continue ; } -if (irq >0 ) { +if (port->error_irq >0 || port->intx_irq >0 ) { ret =mvebu_pcie_init_irq_domain (port);if (ret) { dev_err(dev, "%s: cannot init irq domain\n",@@ -1577,14 +1761,42 @@ static int mvebu_pcie_probe(struct platform_device *pdev)mvebu_pcie_powerdown (port);continue ; } + } + +if (port->error_irq >0 ) { + ret =devm_request_irq (dev, port->error_irq, + mvebu_pcie_error_irq_handler, +IRQF_SHARED |IRQF_NO_THREAD , + port->name, port); +if (ret) { +dev_err (dev,"%s: cannot register error interrupt handler: %d\n" , + port->name, ret); +if (port->intx_irq_domain) +irq_domain_remove (port->intx_irq_domain); +if (port->rp_irq_domain) +irq_domain_remove (port->rp_irq_domain); +pci_bridge_emul_cleanup (&port->bridge); +devm_iounmap (dev, port->base); + port->base =NULL ; +mvebu_pcie_powerdown (port); +continue ; + } + } - ret =devm_request_irq (dev, irq, mvebu_pcie_irq_handler, +if (port->intx_irq >0 ) { + ret =devm_request_irq (dev, port->intx_irq, + mvebu_pcie_intx_irq_handler,IRQF_SHARED |IRQF_NO_THREAD , port->name, port);if (ret) { -dev_err (dev,"%s: cannot register interrupt handler: %d\n" , +dev_err (dev,"%s: cannot register intx interrupt handler: %d\n" , port->name, ret); -irq_domain_remove (port->intx_irq_domain); +if (port->error_irq >0 ) +devm_free_irq (dev, port->error_irq, port); +if (port->intx_irq_domain) +irq_domain_remove (port->intx_irq_domain); +if (port->rp_irq_domain) +irq_domain_remove (port->rp_irq_domain);pci_bridge_emul_cleanup (&port->bridge);devm_iounmap (dev, port->base); port->base =NULL ;@@ -1722,6 +1934,12 @@ static int mvebu_pcie_remove(struct platform_device *pdev) }irq_domain_remove (port->intx_irq_domain); } +if (port->rp_irq_domain) { +int virq =irq_find_mapping (port->rp_irq_domain,0 ); +if (virq >0 ) +irq_dispose_mapping (virq); +irq_domain_remove (port->rp_irq_domain); + }/* Free config space for emulated root bridge. */ pci_bridge_emul_cleanup (&port->bridge);Signature · 1 line
2.20.1
Lorenzo Pieralisi
maintainerRe: [PATCH 2/4] PCI: mvebu: Implement support for interrupts on emulated bridge
Quoted 9 lines · Pali Rohár
Hello!
Gentle reminder for this patch. It is waiting there for more than month and other patches from this patch series were already reviewed and merged. Could you please look at it?
As stated in commit message this patch adds support for PCIe AER to
pci-mvebu.cand as we know AER required for debugging any PCIe endpoint issues.
I thought this patch has a dependency on other patches that I can't merge and therefore I postponed reviewing it:
https://lore.kernel.org/linux-pci/20220830123639.4zpvvvlrsaqs2rls@pali/
Quoted 441 lines · On Tuesday 30 August 2022 14:36:39 Pali Rohár wrote:
Quoted 430 lines · On Thursday 18 August 2022 01:00:34 Pali Rohár wrote:
Quoted 12 lines
This adds support for PME and ERR interrupts reported by emulated bridge (for PME and AER kernel drivers) via new Root Port irq chip as these interrupts from PCIe Root Ports are handled by mvebu hardware completely separately from INTx and MSI interrupts send by real PCIe devices.
With this change, kernel PME and AER drivers start working as they can acquire required interrupt lines (provided by mvebu rp virtual irq chip).
Note that for this support, device tree files has to be properly adjusted to provide "interrupts" or "interrupts-extended" property with error interrupt source and "interrupt-names" property with "error" string.
Quoted 5 lines
If device tree files do not provide these properties then driver would work as before and would not provide interrupts on emulated bridge, like before.
Signed-off-by Pali Rohár <[email protected]>---
Just to note that because these error interrupts are shared on some mvebu platforms, this patch depends on another patch which convert driver to
devm_request_irq()and which I sent more months before:
https://lore.kernel.org/linux-pci/[email protected]/Quoted 406 lines
drivers/pci/controller/pci-mvebu.c | 256 ++++++++++++++++++++++++++--- 1 file changed, 237 insertions(+), 19 deletions(-)drivers/pci/controller/pci-mvebu.c +237
-19@@ -56,8 +56,16 @@#define PCIE_CONF_DATA_OFF 0x18fc#define PCIE_INT_CAUSE_OFF 0x1900#define PCIE_INT_UNMASK_OFF 0x1910 +#define PCIE_INT_DET_COR BIT(8) +#define PCIE_INT_DET_NONFATAL BIT(9) +#define PCIE_INT_DET_FATAL BIT(10) +#define PCIE_INT_ERR_FATAL BIT(16) +#define PCIE_INT_ERR_NONFATAL BIT(17) +#define PCIE_INT_ERR_COR BIT(18)#define PCIE_INT_INTX (i) BIT(24+i)#define PCIE_INT_PM_PME BIT(28) +#define PCIE_INT_DET_MASK (PCIE_INT_DET_COR | PCIE_INT_DET_NONFATAL | PCIE_INT_DET_FATAL) +#define PCIE_INT_ERR_MASK (PCIE_INT_ERR_FATAL | PCIE_INT_ERR_NONFATAL | PCIE_INT_ERR_COR)#define PCIE_INT_ALL_MASK GENMASK(31, 0)#define PCIE_CTRL_OFF 0x1a00#define PCIE_CTRL_X1_MODE 0x0001@@ -120,9 +128,12 @@ struct mvebu_pcie_port {struct resource regs;u8 slot_power_limit_value;u8 slot_power_limit_scale; +struct irq_domain *rp_irq_domain;struct irq_domain *intx_irq_domain;raw_spinlock_t irq_lock; +int error_irq;int intx_irq; +bool pme_pending; };static inline void mvebu_writel (struct mvebu_pcie_port *port,u32 val,u32 reg)@@ -321,9 +332,19 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port)/* Clear all interrupt causes. */ mvebu_writel (port, ~PCIE_INT_ALL_MASK ,PCIE_INT_CAUSE_OFF ); -/* Check if "intx" interrupt was specified in DT. */ -if (port->intx_irq >0 ) -return ; +/* +* Unmask all error interrupts which are internally generated. +* They cannot be disabled by SERR# Enable bit in PCI Command register, +* see Figure 6-3: Pseudo Logic Diagram for Error Message Controls in +* PCIe base specification. +* Internally generated mvebu interrupts are reported via mvebu summary +* interrupt which requires "error" interrupt to be specified in DT. +*/ +if (port->error_irq >0 ) { + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + unmask |=PCIE_INT_DET_MASK ; +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + }/* * Fallback code when "intx" interrupt was not specified in DT: @@ -335,10 +356,12 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port)* performance penalty as every PCIe interrupt handler needs to be * called when some interrupt is triggered. */ - unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); - unmask |=PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | -PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ); -mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); +if (port->intx_irq <=0 ) { + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + unmask |=PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ); +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + } } static struct mvebu_pcie_port *mvebu_pcie_find_port(struct mvebu_pcie *pcie,@@ -603,11 +626,16 @@ mvebu_pci_bridge_emul_base_conf_read(struct pci_bridge_emul *bridge,case PCI_INTERRUPT_LINE : {/* * From the whole 32bit register we support reading from HW only -* one bit: PCI_BRIDGE_CTL_BUS_RESET. +* two bits: PCI_BRIDGE_CTL_BUS_RESET and PCI_BRIDGE_CTL_SERR. * Other bits are retrieved only from emulated config buffer. */ __le32 *cfgspace = (__le32 *)&bridge->conf;u32 val =le32_to_cpu (cfgspace[PCI_INTERRUPT_LINE /4 ]); +if ((mvebu_readl (port,PCIE_INT_UNMASK_OFF ) & +PCIE_INT_ERR_MASK ) ==PCIE_INT_ERR_MASK ) + val |=PCI_BRIDGE_CTL_SERR <<16 ; +else + val &= ~(PCI_BRIDGE_CTL_SERR <<16 );if (mvebu_readl (port,PCIE_CTRL_OFF ) &PCIE_CTRL_MASTER_HOT_RESET ) val |=PCI_BRIDGE_CTL_BUS_RESET <<16 ;else @@ -675,6 +703,11 @@ mvebu_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge,break ; } +case PCI_EXP_RTCTL : + *value = (mvebu_readl (port,PCIE_INT_UNMASK_OFF ) & +PCIE_INT_PM_PME ) ?PCI_EXP_RTCTL_PMEIE :0 ; +break ; +case PCI_EXP_RTSTA : *value =mvebu_readl (port,PCIE_RC_RTSTA );break ;@@ -780,6 +813,14 @@ mvebu_pci_bridge_emul_base_conf_write(struct pci_bridge_emul *bridge,break ;case PCI_INTERRUPT_LINE : +if ((mask & (PCI_BRIDGE_CTL_SERR <<16 )) && port->error_irq >0 ) { +u32 unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); +if (new & (PCI_BRIDGE_CTL_SERR <<16 )) + unmask |=PCIE_INT_ERR_MASK ; +else + unmask &= ~PCIE_INT_ERR_MASK ; +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + }if (mask & (PCI_BRIDGE_CTL_BUS_RESET <<16 )) {u32 ctrl =mvebu_readl (port,PCIE_CTRL_OFF );if (new & (PCI_BRIDGE_CTL_BUS_RESET <<16 ))@@ -838,10 +879,25 @@ mvebu_pci_bridge_emul_pcie_conf_write(struct pci_bridge_emul *bridge,* PME Status bit in Root Status Register (PCIE_RC_RTSTA) * is read-only and can be cleared only by writing 0b to the * Interrupt Cause RW0C register (PCIE_INT_CAUSE_OFF). So -* clear PME via Interrupt Cause. +* clear PME via Interrupt Cause and also set port->pme_pending +* variable to false value to start processing PME interrupts +* in interrupt handler again. */ -if (new &PCI_EXP_RTSTA_PME ) +if (new &PCI_EXP_RTSTA_PME ) {mvebu_writel (port, ~PCIE_INT_PM_PME ,PCIE_INT_CAUSE_OFF ); + port->pme_pending = false; + } +break ; + +case PCI_EXP_RTCTL : +if ((mask &PCI_EXP_RTCTL_PMEIE ) && port->error_irq >0 ) { +u32 unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); +if (new &PCI_EXP_RTCTL_PMEIE ) + unmask |=PCIE_INT_PM_PME ; +else + unmask &= ~PCIE_INT_PM_PME ; +mvebu_writel (port, unmask,PCIE_INT_UNMASK_OFF ); + }break ;case PCI_EXP_DEVCTL2 :@@ -924,6 +980,14 @@ static int mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port) bridge_flags |=PCI_BRIDGE_EMUL_NO_IO_FORWARD ; } +/* +* Interrupts on emulated bridge are supported only when "error" +* interrupt was specified in DT. Without it emulated bridge cannot +* emulate interrupts. +*/ +if (port->error_irq >0 ) + bridge->conf.intpin =PCI_INTERRUPT_INTA ; +/* * Older mvebu hardware provides PCIe Capability structure only in * version 1. New hardware provides it in version 2. @@ -1072,6 +1136,26 @@ static const struct irq_domain_ops mvebu_pcie_intx_irq_domain_ops = { .xlate = irq_domain_xlate_onecell, }; +static struct irq_chip rp_irq_chip = { + .name ="mvebu-rp" , +}; + +static int mvebu_pcie_rp_irq_map (struct irq_domain *h, +unsigned int virq,irq_hw_number_t hwirq) +{ +struct mvebu_pcie_port *port = h->host_data; + +irq_set_chip_and_handler (virq, &rp_irq_chip, handle_simple_irq); +irq_set_chip_data (virq, port); + +return 0 ; +} + +static const struct irq_domain_ops mvebu_pcie_rp_irq_domain_ops = { + .map = mvebu_pcie_rp_irq_map, + .xlate = irq_domain_xlate_onecell, +}; +static int mvebu_pcie_init_irq_domain (struct mvebu_pcie_port *port) {struct device *dev = &port->pcie->pdev->dev;@@ -1094,10 +1178,72 @@ static int mvebu_pcie_init_irq_domain(struct mvebu_pcie_port *port)return -ENOMEM ; } +/* +* When "error" interrupt was not specified in DT then there is no +* support for interrupts on emulated root bridge. So skip following +* initialization. +*/ +if (port->error_irq <=0 ) +return 0 ; + + port->rp_irq_domain =irq_domain_add_linear (NULL ,1 , + &mvebu_pcie_rp_irq_domain_ops, + port); +if (!port->rp_irq_domain) { +irq_domain_remove (port->intx_irq_domain); +dev_err (dev,"Failed to add Root Port IRQ domain for %s\n" , port->name); +return -ENOMEM ; + } +return 0 ; } -static irqreturn_t mvebu_pcie_irq_handler (int irq,void *arg) +static irqreturn_t mvebu_pcie_error_irq_handler (int irq,void *arg) +{ +struct mvebu_pcie_port *port = arg; +struct device *dev = &port->pcie->pdev->dev; +u32 cause, unmask, status; + + cause =mvebu_readl (port,PCIE_INT_CAUSE_OFF ); + unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); + status = cause & unmask; + +/* "error" interrupt handler does not process INTX interrupts */ + status &= ~(PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 )); + +/* Process PME interrupt */ +if ((status &PCIE_INT_PM_PME ) && !port->pme_pending) { +/* +* Do not clear PME interrupt bit in Cause Register as it +* invalidates also content of Root Status Register. Instead +* set port->pme_pending variable to true to indicate that +* next time PME interrupt should be ignored until variable +* is back to the false value. +*/ + port->pme_pending = true; +if (generic_handle_domain_irq (port->rp_irq_domain,0 ) == -EINVAL ) +dev_err_ratelimited (dev,"unhandled PME IRQ\n" ); + } + +/* Process ERR interrupt */ +if (status &PCIE_INT_ERR_MASK ) { +mvebu_writel (port, ~PCIE_INT_ERR_MASK ,PCIE_INT_CAUSE_OFF ); +if (generic_handle_domain_irq (port->rp_irq_domain,0 ) == -EINVAL ) +dev_err_ratelimited (dev,"unhandled ERR IRQ\n" ); + } + +/* Process local ERR interrupt */ +if (status &PCIE_INT_DET_MASK ) { +mvebu_writel (port, ~PCIE_INT_DET_MASK ,PCIE_INT_CAUSE_OFF ); +if (generic_handle_domain_irq (port->rp_irq_domain,0 ) == -EINVAL ) +dev_err_ratelimited (dev,"unhandled ERR IRQ\n" ); + } + +return status ?IRQ_HANDLED :IRQ_NONE ; +} + +static irqreturn_t mvebu_pcie_intx_irq_handler (int irq,void *arg) {struct mvebu_pcie_port *port = arg;struct device *dev = &port->pcie->pdev->dev;@@ -1108,6 +1254,10 @@ static irqreturn_t mvebu_pcie_irq_handler(int irq, void *arg) unmask =mvebu_readl (port,PCIE_INT_UNMASK_OFF ); status = cause & unmask; +/* "intx" interrupt handler process only INTX interrupts */ + status &=PCIE_INT_INTX (0 ) |PCIE_INT_INTX (1 ) | +PCIE_INT_INTX (2 ) |PCIE_INT_INTX (3 ); +/* Process legacy INTx interrupts */ for (i =0 ; i <PCI_NUM_INTX ; i++) {if (!(status &PCIE_INT_INTX (i)))@@ -1122,9 +1272,29 @@ static irqreturn_t mvebu_pcie_irq_handler(int irq, void *arg)static int mvebu_pcie_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) { -/* Interrupt support on mvebu emulated bridges is not implemented yet */ -if (dev->bus->number ==0 ) -return 0 ;/* Proper return code 0 == NO_IRQ */ +struct mvebu_pcie_port *port; +struct mvebu_pcie *pcie; + +if (dev->bus->number ==0 ) { +/* +* Each emulated root bridge for every mvebu port has its own +* Root Port irq chip and irq domain. Argument pin is the INTx +* pin (1=INTA, 2=INTB, 3=INTC, 4=INTD) and hwirq for function +* irq_create_mapping() is indexed from zero. +*/ + pcie = dev->bus->sysdata; + port =mvebu_pcie_find_port (pcie, dev->bus,PCI_DEVFN (slot,0 )); +if (!port) +return 0 ;/* Proper return code 0 == NO_IRQ */ +/* +* port->rp_irq_domain is available only when "error" interrupt +* was specified in DT. When is not available then interrupts +* for emulated root bridge are not provided. +*/ +if (port->error_irq <=0 ) +return 0 ;/* Proper return code 0 == NO_IRQ */ +return irq_create_mapping (port->rp_irq_domain, pin -1 ); + }return of_irq_parse_and_map_pci (dev, slot, pin); }@@ -1333,6 +1503,21 @@ static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie, port->name, child); } +/* +* Old DT bindings do not contain "error" interrupt +* so do not fail probing driver when interrupt does not exist. +*/ + port->error_irq =of_irq_get_byname (child,"error" ); +if (port->error_irq == -EPROBE_DEFER ) { + ret = port->error_irq; + goto err; + } +if (port->error_irq <=0 ) { +dev_warn (dev,"%s: interrupts on Root Port are unsupported, " +"%pOF does not contain error interrupt\n" , + port->name, child); + } + reset_gpio =of_get_named_gpio_flags (child,"reset-gpios" ,0 , &flags);if (reset_gpio == -EPROBE_DEFER ) { ret = reset_gpio;@@ -1538,7 +1723,6 @@ static int mvebu_pcie_probe(struct platform_device *pdev)for (i =0 ; i < pcie->nports; i++) {struct mvebu_pcie_port *port = &pcie->ports[i]; -int irq = port->intx_irq; child = port->dn;if (!child)@@ -1566,7 +1750,7 @@ static int mvebu_pcie_probe(struct platform_device *pdev)continue ; } -if (irq >0 ) { +if (port->error_irq >0 || port->intx_irq >0 ) { ret =mvebu_pcie_init_irq_domain (port);if (ret) { dev_err(dev, "%s: cannot init irq domain\n",@@ -1577,14 +1761,42 @@ static int mvebu_pcie_probe(struct platform_device *pdev)mvebu_pcie_powerdown (port);continue ; } + } + +if (port->error_irq >0 ) { + ret =devm_request_irq (dev, port->error_irq, + mvebu_pcie_error_irq_handler, +IRQF_SHARED |IRQF_NO_THREAD , + port->name, port); +if (ret) { +dev_err (dev,"%s: cannot register error interrupt handler: %d\n" , + port->name, ret); +if (port->intx_irq_domain) +irq_domain_remove (port->intx_irq_domain); +if (port->rp_irq_domain) +irq_domain_remove (port->rp_irq_domain); +pci_bridge_emul_cleanup (&port->bridge); +devm_iounmap (dev, port->base); + port->base =NULL ; +mvebu_pcie_powerdown (port); +continue ; + } + } - ret =devm_request_irq (dev, irq, mvebu_pcie_irq_handler, +if (port->intx_irq >0 ) { + ret =devm_request_irq (dev, port->intx_irq, + mvebu_pcie_intx_irq_handler,IRQF_SHARED |IRQF_NO_THREAD , port->name, port);if (ret) { -dev_err (dev,"%s: cannot register interrupt handler: %d\n" , +dev_err (dev,"%s: cannot register intx interrupt handler: %d\n" , port->name, ret); -irq_domain_remove (port->intx_irq_domain); +if (port->error_irq >0 ) +devm_free_irq (dev, port->error_irq, port); +if (port->intx_irq_domain) +irq_domain_remove (port->intx_irq_domain); +if (port->rp_irq_domain) +irq_domain_remove (port->rp_irq_domain);pci_bridge_emul_cleanup (&port->bridge);devm_iounmap (dev, port->base); port->base =NULL ;@@ -1722,6 +1934,12 @@ static int mvebu_pcie_remove(struct platform_device *pdev) }irq_domain_remove (port->intx_irq_domain); } +if (port->rp_irq_domain) { +int virq =irq_find_mapping (port->rp_irq_domain,0 ); +if (virq >0 ) +irq_dispose_mapping (virq); +irq_domain_remove (port->rp_irq_domain); + }Quoted 5 lines
Quoted 5 lines
drivers/pci/controller/pci-mvebu.c +0
-0/* Free config space for emulated root bridge. */ pci_bridge_emul_cleanup (&port->bridge);Signature · 1 line
2.20.1_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Pali Rohár
maintainerPATCH 3/4 ARM: dts: kirkwood: Add definitions for PCIe error interrupts
In reply to Pali RohárFirst PCIe controller on Kirkwood SoC reports error interrupt via IRQ 44 and second PCIe controller via IRQ 45.
--- arch/arm/boot/dts/kirkwood-6192.dtsi | 4 ++-- arch/arm/boot/dts/kirkwood-6281.dtsi | 4 ++-- arch/arm/boot/dts/kirkwood-6282.dtsi | 8 ++++---- arch/arm/boot/dts/kirkwood-98dx4122.dtsi | 4 ++-- 4 files changed, 10 insertions(+), 10 deletions(-)
arch/arm/boot/dts/kirkwood-6192.dtsi +2 -2
@@ -26,8 +26,8 @@ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 0x81000000 0 0 0x81000000 0x1 0 1 0>; bus-range = <0x00 0xff>; - interrupt-names = "intx"; - interrupts = <9>; + interrupt-names = "intx", "error"; + interrupts = <9>, <44>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc 0>, <0 0 0 2 &pcie_intc 1>,
arch/arm/boot/dts/kirkwood-6281.dtsi +2 -2
@@ -26,8 +26,8 @@ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 0x81000000 0 0 0x81000000 0x1 0 1 0>; bus-range = <0x00 0xff>; - interrupt-names = "intx"; - interrupts = <9>; + interrupt-names = "intx", "error"; + interrupts = <9>, <44>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc 0>, <0 0 0 2 &pcie_intc 1>,
arch/arm/boot/dts/kirkwood-6282.dtsi +4 -4
@@ -30,8 +30,8 @@ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 0x81000000 0 0 0x81000000 0x1 0 1 0>; bus-range = <0x00 0xff>; - interrupt-names = "intx"; - interrupts = <9>; + interrupt-names = "intx", "error"; + interrupts = <9>, <44>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie0_intc 0>, <0 0 0 2 &pcie0_intc 1>,
@@ -58,8 +58,8 @@ ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 0x81000000 0 0 0x81000000 0x2 0 1 0>; bus-range = <0x00 0xff>; - interrupt-names = "intx"; - interrupts = <10>; + interrupt-names = "intx", "error"; + interrupts = <10>, <45>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie1_intc 0>, <0 0 0 2 &pcie1_intc 1>,
arch/arm/boot/dts/kirkwood-98dx4122.dtsi +2 -2
@@ -26,8 +26,8 @@ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 0x81000000 0 0 0x81000000 0x1 0 1 0>; bus-range = <0x00 0xff>; - interrupt-names = "intx"; - interrupts = <9>; + interrupt-names = "intx", "error"; + interrupts = <9>, <44>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie_intc 0>, <0 0 0 2 &pcie_intc 1>,
Signature · 1 line
2.20.1
Re: [PATCH 3/4] ARM: dts: kirkwood: Add definitions for PCIe error interrupts
Quoted 4 lines · Pali Rohár
First PCIe controller on Kirkwood SoC reports error interrupt via IRQ 44 and second PCIe controller via IRQ 45.
Signed-off-by Pali Rohár <[email protected]>
Andrew
Pali Rohár
maintainerPATCH 4/4 ARM: dts: dove: Add definitions for PCIe error interrupts
In reply to Pali RohárFirst PCIe controller on Dove SoC reports error interrupt via IRQ 15 and second PCIe controller via IRQ 17.
--- arch/arm/boot/dts/dove.dtsi | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
arch/arm/boot/dts/dove.dtsi +4 -4
@@ -122,8 +122,8 @@ bus-range = <0x00 0xff>; #interrupt-cells = <1>; - interrupt-names = "intx"; - interrupts = <16>; + interrupt-names = "intx", "error"; + interrupts = <16>, <15>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie0_intc 0>, <0 0 0 2 &pcie0_intc 1>,
@@ -151,8 +151,8 @@ bus-range = <0x00 0xff>; #interrupt-cells = <1>; - interrupt-names = "intx"; - interrupts = <18>; + interrupt-names = "intx", "error"; + interrupts = <18>, <17>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &pcie1_intc 0>, <0 0 0 2 &pcie1_intc 1>,
Signature · 1 line
2.20.1
Re: [PATCH 4/4] ARM: dts: dove: Add definitions for PCIe error interrupts
Quoted 4 lines · Pali Rohár
First PCIe controller on Dove SoC reports error interrupt via IRQ 15 and second PCIe controller via IRQ 17.
Signed-off-by Pali Rohár <[email protected]>
Andrew
Quoted 19 lines · Pali Rohár
PCI mvebu error interrupt source is triggered for non-INTx event. So e.g. when AER or PME event occurs.
This patch series adds support for reporting AER and PME interrupts on Marvell PCIe Root Ports which allows use to kernel AER and PME drivers.
Without this change kernel AER and PME drivers do not work at all.
DT bindings for this support is currently provided only for Kirkwood and Dove platforms as other new mvebu SoCs requires extension to armada IRQ driver, which is currently disallowed.
Without new DTS files,
pci-mvebu.cdriver acts as before this change, there is no AER and PME kernel support.I have tested this change on Armada 385 board (with additional changes to A385 DTS files and IRQ driver, not included there) and AER interrupt is delivered to kernel AER driver correctly.
Quoted 7 lines
Pali Rohár (4):
dt-bindings: PCI: mvebu: Update information about error interrupt
PCI: mvebu: Implement support for interrupts on emulated bridgeARM: dts: kirkwood: Add definitions for PCIe error interrupts
ARM: dts: dove: Add definitions for PCIe error interrupts
Applied both dts patches on mvebu/dt
Thanks,
Gregory
Quoted 13 lines
.../devicetree/bindings/pci/mvebu-pci.txt | 1 + arch/arm/boot/dts/dove.dtsi | 8 +- arch/arm/boot/dts/kirkwood-6192.dtsi | 4 +- arch/arm/boot/dts/kirkwood-6281.dtsi | 4 +- arch/arm/boot/dts/kirkwood-6282.dtsi | 8 +- arch/arm/boot/dts/kirkwood-98dx4122.dtsi | 4 +- drivers/pci/controller/pci-mvebu.c | 256 ++++++++++++++++-- 7 files changed, 252 insertions(+), 33 deletions(-)Signature · 1 line
2.20.1
Signature · 8 lines
Gregory Clement, Bootlin Embedded Linux and Kernel engineering http://bootlin.com _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel