ath10k: Enable support for beacon interval per VAP
PATCH v2 1/1 ath10k: Enable support for beacon interval per VAP
Enable support to configure different beacon interval per VAP.
To support this feature, map different beacon interval service bit to wmi tlv service.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
---
This change is dependent on the below patchset
ath10k: Add support for ack rssi value of management tx packets (https://patchwork.kernel.org/patch/10809631/)
--- drivers/net/wireless/ath/ath10k/mac.c | 33 +++++++++++++++++++++++++++++++ drivers/net/wireless/ath/ath10k/wmi-tlv.h | 3 +++ 2 files changed, 36 insertions(+)
drivers/net/wireless/ath/ath10k/mac.c +33 -0
@@ -8232,6 +8232,30 @@ void ath10k_mac_destroy(struct ath10k *ar) }, }; +static struct +ieee80211_iface_combination ath10k_tlv_qcs_bcn_int_if_comb[] = { + { + .limits = ath10k_tlv_if_limit, + .num_different_channels =1 , + .max_interfaces =4 , + .beacon_int_infra_match = true, + .beacon_int_min_gcd =1 , + .n_limits =ARRAY_SIZE (ath10k_tlv_if_limit), + }, + { + .limits = ath10k_tlv_qcs_if_limit, + .num_different_channels =2 , + .max_interfaces =4 , + .n_limits =ARRAY_SIZE (ath10k_tlv_qcs_if_limit), + }, + { + .limits = ath10k_tlv_if_limit_ibss, + .num_different_channels =1 , + .max_interfaces =2 , + .n_limits =ARRAY_SIZE (ath10k_tlv_if_limit_ibss), + }, +}; +static const struct ieee80211_iface_limit ath10k_10_4_if_limits[] = { { .max =1 ,
@@ -8642,6 +8666,15 @@ int ath10k_mac_register(struct ath10k *ar) ath10k_tlv_qcs_if_comb; ar->hw->wiphy->n_iface_combinations =ARRAY_SIZE (ath10k_tlv_qcs_if_comb); + +if (test_bit + (WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT , + ar->wmi.svc_map)) { + ar->hw->wiphy->iface_combinations = + ath10k_tlv_qcs_bcn_int_if_comb; + ar->hw->wiphy->n_iface_combinations = +ARRAY_SIZE (ath10k_tlv_qcs_bcn_int_if_comb); + } }else { ar->hw->wiphy->iface_combinations = ath10k_tlv_if_comb; ar->hw->wiphy->n_iface_combinations =
drivers/net/wireless/ath/ath10k/wmi-tlv.h +3 -0
@@ -1567,6 +1567,9 @@ enum wmi_tlv_service {SVCMAP (WMI_TLV_SERVICE_THERM_THROT ,WMI_SERVICE_THERM_THROT ,WMI_TLV_MAX_SERVICE ); +SVCMAP (WMI_TLV_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT , +WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT , +WMI_TLV_MAX_SERVICE ); }#undef SVCMAP
Signature · 1 line
1.9.1
Quoted 9 lines · Dundi Raviteja
Enable support to configure different beacon interval per VAP.
To support this feature, map different beacon interval service bit to wmi tlv service.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1Signed-off-by Dundi Raviteja <[email protected]>
[...]
Quoted 36 lines
drivers/net/wireless/ath/ath10k/mac.c +24
-0@@ -8232,6 +8232,30 @@ void ath10k_mac_destroy(struct ath10k *ar) }, }; +static struct +ieee80211_iface_combination ath10k_tlv_qcs_bcn_int_if_comb[] = { + { + .limits = ath10k_tlv_if_limit, + .num_different_channels =1 , + .max_interfaces =4 , + .beacon_int_infra_match = true, + .beacon_int_min_gcd =1 , + .n_limits =ARRAY_SIZE (ath10k_tlv_if_limit), + }, + { + .limits = ath10k_tlv_qcs_if_limit, + .num_different_channels =2 , + .max_interfaces =4 , + .n_limits =ARRAY_SIZE (ath10k_tlv_qcs_if_limit), + }, + { + .limits = ath10k_tlv_if_limit_ibss, + .num_different_channels =1 , + .max_interfaces =2 , + .n_limits =ARRAY_SIZE (ath10k_tlv_if_limit_ibss), + }, +}; +static const struct ieee80211_iface_limit ath10k_10_4_if_limits[] = { { .max =1 ,@@ -8642,6 +8666,15 @@ int ath10k_mac_register(struct ath10k *ar)ath10k_tlv_qcs_if_comb ; ar->hw->wiphy->n_iface_combinations =
drivers/net/wireless/ath/ath10k/mac.c int ath10k_mac_register(struct ath10k *ar) · line 8677
Quoted 10 lines
drivers/net/wireless/ath/ath10k/mac.c +9
-0ARRAY_SIZE (ath10k_tlv_qcs_if_comb); + +if (test_bit + (WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT , + ar->wmi.svc_map)) { + ar->hw->wiphy->iface_combinations = + ath10k_tlv_qcs_bcn_int_if_comb; + ar->hw->wiphy->n_iface_combinations = +ARRAY_SIZE (ath10k_tlv_qcs_bcn_int_if_comb); + }
I don't like using WMI service flags to advertise different interface combinations, it makes ath10k code convoluted. A much better approach is to use WMI_SERVICE_IFACE_COMBINATION_SUPPORT:
ath10k:New interface to get interface combinations from FW
https://patchwork.kernel.org/patch/11027361/
Signature · 6 lines
Kalle Valo _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k