gpio: mpc8xxx: don't set IRQ_TYPE_NONE when creating irq mapping
PATCH 1/1 gpio: mpc8xxx: don't set IRQ_TYPE_NONE when creating irq mapping
Exporting gpios throws genirq error messages like
genirq: Setting trigger mode 0 for irq 44 failed
(mpc512x_irq_set_type+0x0/0x18c)
Do not set IRQ_TYPE_NONE in mapping function. Setting this type here ends up in returning error code in driver's irq_set_type() function and this triggers the genirq error message.
--- drivers/gpio/gpio-mpc8xxx.c | 1 - 1 file changed, 1 deletion(-)
drivers/gpio/gpio-mpc8xxx.c +0 -1
@@ -292,7 +292,6 @@ static int mpc8xxx_gpio_irq_map(struct irq_domain *h, unsigned int virq,irq_set_chip_data (virq, h->host_data);irq_set_chip_and_handler (virq, &mpc8xxx_irq_chip, handle_level_irq); -irq_set_irq_type (virq,IRQ_TYPE_NONE );return 0 ; }
Signature · 1 line
1.7.11.7
Quoted 19 lines · Anatolij Gustschin
Exporting gpios throws genirq error messages like
genirq: Setting trigger mode 0 for irq 44 failed
(mpc512x_irq_set_type+0x0/0x18c)Do not set
IRQ_TYPE_NONEin mapping function. Setting this type here ends up in returning error code in driver'sirq_set_type()function and this triggers the genirq error message.Signed-off-by Anatolij Gustschin <[email protected]>--- drivers/gpio/gpio-mpc8xxx.c | 1 - 1 file changed, 1 deletion(-)drivers/gpio/gpio-mpc8xxx.c +0
-0
drivers/gpio/gpio-mpc8xxx.c static int mpc8xxx_gpio_irq_map(struct irq_domain *h, unsigned int virq, · line 295
Quoted 4 lines
drivers/gpio/gpio-mpc8xxx.c +0
-1@@ -292,7 +292,6 @@ static int mpc8xxx_gpio_irq_map(struct irq_domain *h, unsigned int virq,irq_set_chip_data (virq, h->host_data);irq_set_chip_and_handler (virq, &mpc8xxx_irq_chip, handle_level_irq); -irq_set_irq_type (virq,IRQ_TYPE_NONE );
git blame says this line was put there by the IRQ subsystem maintainer Thomas Gleixner.
I feel very nervous about removing that, and you need a better explanation what is causing the problem and how in the commit.
Like I want to know for sure that the problem is not triggered from somewhere else.
Please write how and where you export this to trigger the error.
Yours,
Linus Walleij
Quoted 22 lines · On Sat, 2 Feb 2013 16:11:03 +0100 Linus Walleij <[email protected]>…
Quoted 20 lines · Anatolij Gustschin
Exporting gpios throws genirq error messages like
genirq: Setting trigger mode 0 for irq 44 failed
(mpc512x_irq_set_type+0x0/0x18c)Do not set
IRQ_TYPE_NONEin mapping function. Setting this type here ends up in returning error code in driver'sirq_set_type()function and this triggers the genirq error message.Signed-off-by Anatolij Gustschin <[email protected]>--- drivers/gpio/gpio-mpc8xxx.c | 1 - 1 file changed, 1 deletion(-)drivers/gpio/gpio-mpc8xxx.c +0
-0@@ -292,7 +292,6 @@ static int mpc8xxx_gpio_irq_map(struct irq_domain *h, unsigned int virq,
Quoted 6 lines
drivers/gpio/gpio-mpc8xxx.c static int mpc8xxx_gpio_irq_map(struct irq_domain *h, unsigned int virq, · line 295
Quoted 3 lines
drivers/gpio/gpio-mpc8xxx.c +0
-1irq_set_chip_data (virq, h->host_data);irq_set_chip_and_handler (virq, &mpc8xxx_irq_chip, handle_level_irq); -irq_set_irq_type (virq,IRQ_TYPE_NONE );git blame says this line was put there by the IRQ subsystem maintainer Thomas Gleixner.
Thomas renamed the old set_irq_type() call to irq_set_irq_type(), but this line setting the IRQ_TYPE_NONE type was there before renaming. It was added by commit 345e5c8a. At this time set_irq_type() checked its type argument and returned 0 if the type argument didn't specify some meaningful type in its type sense bits (and thus was equal to IRQ_TYPE_NONE). Effectively this line was a nop and I wonder what was the point of adding it.
Quoted 7 lines
I feel very nervous about removing that, and you need a better explanation what is causing the problem and how in the commit.
Like I want to know for sure that the problem is not triggered from somewhere else.
Please write how and where you export this to trigger the error.
It is very simple to trigger the error, i.e. on mpc5121 based board using mpc8xxx-gpio driver and exporting GPIO pins over sysfs gpio interface triggers it:
# cat /sys/class/gpio/gpiochip224/base 224 # echo 229 > /sys/class/gpio/export [ 83.753709] genirq: Setting trigger mode 0 for irq 44 failed (mpc512x_irq_set_type+0x0/0x164)
Similar error messages appear in the kernel boot log since the board specifies GPIOs for matrix keypad and also SD Card write protect and card detect GPIOs in its device tree. For all these GPIOs there is an error message in the log. Here is an example call path shown by dump_stack() added in kernel/irq/manage.c:
[ 1.645277] genirq: Setting trigger mode 0 for irq 38 failed (mpc512x_irq_set_type+0x0/0x164) [ 1.656118] Call Trace: [ 1.658562] [cf83dc60] [c00088cc] show_stack+0x10c/0x1c0 (unreliable) [ 1.664962] [cf83dcb0] [c03ae0e8] dump_stack+0x24/0x34 [ 1.670065] [cf83dcc0] [c006d1bc] __irq_set_trigger+0xb8/0x150 [ 1.675859] [cf83dce0] [c006ea24] irq_set_irq_type+0x4c/0x78 [ 1.681483] [cf83dd10] [c01f1c10] mpc8xxx_gpio_irq_map+0x70/0x88 [ 1.687457] [cf83dd20] [c0070578] irq_domain_associate_many+0x104/0x1e4 [ 1.694032] [cf83dd60] [c00706ec] irq_create_mapping+0x94/0x138 [ 1.699915] [cf83dd80] [c01f1d04] mpc8xxx_gpio_to_irq+0x38/0x48 [ 1.705810] [cf83dd90] [c01edbac] __gpio_to_irq+0x58/0x68 [ 1.711177] [cf83dda0] [c02c1504] matrix_keypad_probe+0x3bc/0x7a8 [ 1.717225] [cf83dde0] [c024b14c] platform_drv_probe+0x2c/0x3c [ 1.723033] [cf83ddf0] [c0249a68] driver_probe_device+0xa0/0x250 [ 1.728993] [cf83de10] [c0249cc0] __driver_attach+0xa8/0xc0 [ 1.734532] [cf83de30] [c0247da0] bus_for_each_dev+0x6c/0xa8 [ 1.740156] [cf83de60] [c02494c8] driver_attach+0x30/0x40 [ 1.745522] [cf83de70] [c0248fe0] bus_add_driver+0x198/0x26c [ 1.751144] [cf83de90] [c024a07c] driver_register+0x94/0x178 [ 1.756770] [cf83deb0] [c024b2f0] platform_driver_register+0x74/0x84 [ 1.763095] [cf83dec0] [c04ec6bc] matrix_keypad_driver_init+0x18/0x28 [ 1.769492] [cf83ded0] [c00039c0] do_one_initcall+0x144/0x1c4 [ 1.775208] [cf83df00] [c04d28d4] kernel_init_freeable+0x110/0x1b4 [ 1.781347] [cf83df30] [c0003fb8] kernel_init+0x20/0x108 [ 1.786634] [cf83df40] [c000ff20] ret_from_kernel_thread+0x5c/0x64
__irq_set_trigger() calls irq_set_type() callback of the mpc8xxx gpio irq chip with the IRQ_TYPE_NONE in its 'flags' argument. This callback is either mpc8xxx_irq_set_type() or mpc512x_irq_set_type(). Both these functions return -EINVAL in the case if IRQ_TYPE_NONE is passed in the flow_type argument. This return value triggers the observed error message in __irq_set_trigger(). Modifying these callbacks to not return an error in IRQ_TYPE_NONE case doesn't make any sense for me, so removing the line as the patch does should be okay. If nobody objects I'll add similar description to commit log of v2 patch.
Turning irq_set_irq_type() into a nop in case of IRQ_TYPE_NONE in its type argument is not acceptable, commit a09b659cd describes the reason.
Thanks,
Anatolij
Peter Korsgaard
Acked-byQuoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
"Anatolij" == Anatolij Gustschin <[email protected]> writes:
Hi,
Anatolij> Thomas renamed the old set_irq_type() call to Anatolij> irq_set_irq_type(), but this line setting the IRQ_TYPE_NONE Anatolij> type was there before renaming. It was added by commit Anatolij> 345e5c8a. At this time set_irq_type() checked its type Anatolij> argument and returned 0 if the type argument didn't specify Anatolij> some meaningful type in its type sense bits (and thus was Anatolij> equal to IRQ_TYPE_NONE). Effectively this line was a nop and Anatolij> I wonder what was the point of adding it.
Sorry, don't recall. It's been quite a while, and I've haven't worked on anything mpc8xxx for a few years by now. Most likely one of the other gpio drivers did it like this back then.
I don't remember the details, but your description makes sense so if nobody disagrees you can have my:
Signature · 1 line
Bye, Peter Korsgaard
PATCH 1/1 gpio: mpc8xxx: don't set IRQ_TYPE_NONE when creating irq mapping
In reply to Anatolij GustschinExporting gpios over sysfs GPIO interface throws genirq error messages, i.e. on an mpc5121 based board exporting GPIO 5 triggers it:
# echo 229 > /sys/class/gpio/export
genirq: Setting trigger mode 0 for irq 44 failed
(mpc512x_irq_set_type+0x0/0x18c)Similar error messages appear in the kernel boot log since the board specifies GPIOs for matrix keypad and also SD Card write protect and card detect GPIOs in its device tree. For all these GPIOs there is an error message in the log.
The issue is triggered by setting the irq type to IRQ_TYPE_NONE in the driver's irq_domain map function mpc8xxx_gpio_irq_map().
...
mpc8xxx_gpio_irq_map
irq_set_irq_type
__irq_set_trigger
__irq_set_trigger() calls irq_set_type() callback of the mpc8xxx gpio irq chip with the IRQ_TYPE_NONE in its 'flags' argument. This callback is either mpc8xxx_irq_set_type() or mpc512x_irq_set_type(). Both these functions return -EINVAL in the case if IRQ_TYPE_NONE is passed in the flow_type argument. This return value triggers the observed error message in __irq_set_trigger(). Modifying these callbacks to not return an error in IRQ_TYPE_NONE case doesn't make any sense to me. The line setting IRQ_TYPE_NONE type has been originally added by commit 345e5c8a "powerpc: Add interrupt support to mpc8xxx_gpio". At this time set_irq_type() checked its type argument and returned 0 if the type argument didn't specify any meaningful type in its type sense bits (and thus was equal to IRQ_TYPE_NONE). Effectively this line was a nop and I wonder what was the point of adding it.
Remove IRQ_TYPE_NONE setting in the irq_domain mapping function.
--- drivers/gpio/gpio-mpc8xxx.c | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)
drivers/gpio/gpio-mpc8xxx.c +0 -1
@@ -292,7 +292,6 @@ static int mpc8xxx_gpio_irq_map(struct irq_domain *h, unsigned int virq,irq_set_chip_data (virq, h->host_data);irq_set_chip_and_handler (virq, &mpc8xxx_irq_chip, handle_level_irq); -irq_set_irq_type (virq,IRQ_TYPE_NONE );return 0 ; }
Signature · 1 line
1.7.5.4
Quoted 3 lines · Anatolij Gustschin
Exporting gpios over sysfs GPIO interface throws genirq error messages, i.e. on an mpc5121 based board exporting GPIO 5 triggers it:
Thanks, I'm convinced now. Applied the v2 patch!
Yours,
Linus Walleij