Skip to contentSkip to conversation

PROBLEM: JVC MP-XP7210 hangs on boot with 2.6.0-test4

DISCUSSION Mario Lang 3 participants 5 messages Aug 29, 2003 – Sep 3, 2003

lore
Share & tools
lore

Mario Lang

author
#0 lore raw

Hi.

I just tried 2.6.0-test4 on my Laptop (JVC MP-XP7210, 256MB RAM, IDE). However, it hangs on boot. I tried booting with acpi=off and also with "acpi=off noapic". Both options seem to help nothing, and the same output appears on all attempts to boot.

I compiled the kernel with gcc 3.3.2.

Here is the output I get:

[<c0 10 92 69>] Kernel_thread_helper+0x5/0xc
Code: 0f ba 6e 24 00 c7 44 24 04 00 00 00 00 89 34 24 e8 25 fa ff

<0> Kernel Panic: Fatal Exception in Interrupt
in interrupt handler - not syncing

(and here it hangs)

P.S.: I am not subscribed, please CC.

Here is also the output of lspci -vv run under 2.4.20-pre7-acpi:

00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 31)

	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 32
	Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=64M]
	Capabilities: [c0] AGP version 2.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) (prog-if 80 [Master])
Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B step)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Region 4: I/O ports at d800 [size=16]

00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:01.1 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 10/100 Ethernet (rev 82)
Subsystem: Asustek Computer, Inc.: Unknown device 1455
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at d400 [size=256]
Region 1: Memory at d3800000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=160mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.2 USB Controller: Silicon Integrated Systems [SiS] SiS7001 USB Controller (rev 07) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] SiS7001 USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), cache line size 08
Interrupt: pin D routed to IRQ 4
Region 0: Memory at d3000000 (32-bit, non-prefetchable) [size=4K]

00:01.3 USB Controller: Silicon Integrated Systems [SiS] SiS7001 USB Controller (rev 07) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] Onboard USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), cache line size 08
Interrupt: pin D routed to IRQ 4
Region 0: Memory at d2800000 (32-bit, non-prefetchable) [size=4K]

00:01.4 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 1473
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin B routed to IRQ 7
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at d2000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=55mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.6 Modem: Silicon Integrated Systems [SiS] Intel 537 [56k Winmodem] (rev a0) (prog-if 00 [Generic])
Subsystem: Asustek Computer, Inc.: Unknown device 1616
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at b800 [size=256]
Region 1: I/O ports at b400 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:02.0 PCI bridge: Silicon Integrated Systems [SiS] SiS 530 Virtual PCI-to-PCI bridge (AGP) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: d1800000-d1ffffff
Prefetchable memory behind bridge: d8000000-e7efffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:09.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 88)

	Subsystem: Asustek Computer, Inc.: Unknown device 1674
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 000de000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
	Memory window 0: 10400000-107ff000 (prefetchable)
	Memory window 1: 10800000-10bff000
	I/O window 0: 00004000-000040ff
	I/O window 1: 00004400-000044ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001

00:09.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 88)

	Subsystem: Asustek Computer, Inc.: Unknown device 1674
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
	Memory window 0: 10c00000-10fff000 (prefetchable)
	Memory window 1: 11000000-113ff000
	I/O window 0: 00004800-000048ff
	I/O window 1: 00004c00-00004cff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001

00:09.2 System peripheral: Ricoh Co Ltd: Unknown device 0576
Subsystem: Asustek Computer, Inc.: Unknown device 1674
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [disabled] [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+

00:0a.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 1677
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max), cache line size 08
Interrupt: pin A routed to IRQ 4
Region 0: Memory at d1000000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at d0800000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+

01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] SiS630 GUI Accelerator+3D (rev 31) (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 1672
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- BIST result: 00
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at d1800000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at a800 [size=128]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] AGP version 2.0
Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

Signature · 2 lines
CYa,
  Mario
#1 lore raw
Quoted 6 lines · Mario Lang

I just tried 2.6.0-test4 on my Laptop (JVC MP-XP7210, 256MB RAM, IDE). However, it hangs on boot. I tried booting with acpi=off and also with "acpi=off noapic". Both options seem to help nothing, and the same output appears on all attempts to boot.

Quoted 8 lines

I compiled the kernel with gcc 3.3.2.

Here is the output I get:

[<c0 10 92 69>] Kernel_thread_helper+0x5/0xc
Code: 0f ba 6e 24 00 c7 44 24 04 00 00 00 00 89 34 24 e8 25 fa ff

<0> Kernel Panic: Fatal Exception in Interrupt
in interrupt handler - not syncing

There must have been more output than that? Please transcribe some more of the backtrace and send it. Don't worry about all the hex numbers: the important parts are these:

EIP is at i810fb_cursor+0x1da/0x240 [i810fb]

 Call Trace:
 [<...>] apic_timer_interrupt+0x1a/0x20
 [<...>] bh_lru_install+0xb5/0x100
 [<...>] __find_get_block+0x73/0xf0
 [<...>] __getblk+0x2b/0x60
 [<...>] is_tree_node+0x6b/0x70
 [<...>] search_by_key+0x6f9/0xf30
 [<...>] search_for_position_by_key+0x1be/0x3d0
 [<...>] apic_timer_interrupt+0x1a/0x20

Also, try stripping your kernel down by unconfiguring drivers and features which are not needed for a successful boot. This will help identify the buggy component.

Also, try adding the string `initcall_debug' to the kernel boot command line. Watch out for the messages "calling initcall 0xNNNNNNNN". Take a note of the final address which is printed before the crash and look it up in the 2.6 kernel's System.map file.

Thanks.

author
#2 lore raw
Quoted 22 lines · Andrew Morton
Quoted 6 lines · Mario Lang

I just tried 2.6.0-test4 on my Laptop (JVC MP-XP7210, 256MB RAM, IDE). However, it hangs on boot. I tried booting with acpi=off and also with "acpi=off noapic". Both options seem to help nothing, and the same output appears on all attempts to boot.

Quoted 8 lines

I compiled the kernel with gcc 3.3.2.

Here is the output I get:

[<c0 10 92 69>] Kernel_thread_helper+0x5/0xc
Code: 0f ba 6e 24 00 c7 44 24 04 00 00 00 00 89 34 24 e8 25 fa ff

<0> Kernel Panic: Fatal Exception in Interrupt
in interrupt handler - not syncing

There must have been more output than that? Please transcribe some more of the backtrace and send it. Don't worry about all the hex numbers: the important parts are these:

EIP is at i810fb_cursor+0x1da/0x240 [i810fb]

Quoted 9 lines
 Call Trace:
 [<...>] apic_timer_interrupt+0x1a/0x20
 [<...>] bh_lru_install+0xb5/0x100
 [<...>] __find_get_block+0x73/0xf0
 [<...>] __getblk+0x2b/0x60
 [<...>] is_tree_node+0x6b/0x70
 [<...>] search_by_key+0x6f9/0xf30
 [<...>] search_for_position_by_key+0x1be/0x3d0
 [<...>] apic_timer_interrupt+0x1a/0x20

Sorry, I did ask a college to type this info for me since I am blind and can't read screen output at that early stage in the boot process. It seems he was very lazy.

Quoted 2 lines

Also, try stripping your kernel down by unconfiguring drivers and features which are not needed for a successful boot.

Thanks you for reminding me! I should have found this myself. The problem was that I accidentally enabled ACPI CPU enumeration support for HT. Well, this is a pIII Mobile, and surely has
no Hyperthreading.

Now the machine boots fine. Only "error" I saw in dmesg is that my chipset is not yet supported for SpeedStep.

Signature · 4 lines
CYa,
  Mario | Debian Developer <URL:http://debian.org/>
        | Get my public key via finger [email protected]
        | 1024D/7FC1A0854909BCCDBE6C102DDFFC022A6B113E44
#4 lore raw
In reply to Mario Lang

OK, I've tried 2.6.0-test4 on my XP7210 and it works just happily. Everything is working: ACPI, PCMCIA, ALSA, SISFB the works...

Maybe it's your version of GCC? I use GCC 3.2.2 which comes with RH9.

Cheers,

Jurgen

Quoted 173 lines · Mario Lang

Hi.

I just tried 2.6.0-test4 on my Laptop (JVC MP-XP7210, 256MB RAM, IDE). However, it hangs on boot. I tried booting with acpi=off and also with "acpi=off noapic". Both options seem to help nothing, and the same output appears on all attempts to boot.

I compiled the kernel with gcc 3.3.2.

Here is the output I get:

[<c0 10 92 69>] Kernel_thread_helper+0x5/0xc
Code: 0f ba 6e 24 00 c7 44 24 04 00 00 00 00 89 34 24 e8 25 fa ff

<0> Kernel Panic: Fatal Exception in Interrupt
in interrupt handler - not syncing

(and here it hangs)

P.S.: I am not subscribed, please CC.

Here is also the output of lspci -vv run under 2.4.20-pre7-acpi:

00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 31)

	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 32
	Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=64M]
	Capabilities: [c0] AGP version 2.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) (prog-if 80 [Master])
Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B step)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Region 4: I/O ports at d800 [size=16]

00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:01.1 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 10/100 Ethernet (rev 82)
Subsystem: Asustek Computer, Inc.: Unknown device 1455
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at d400 [size=256]
Region 1: Memory at d3800000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=160mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.2 USB Controller: Silicon Integrated Systems [SiS] SiS7001 USB Controller (rev 07) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] SiS7001 USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), cache line size 08
Interrupt: pin D routed to IRQ 4
Region 0: Memory at d3000000 (32-bit, non-prefetchable) [size=4K]

00:01.3 USB Controller: Silicon Integrated Systems [SiS] SiS7001 USB Controller (rev 07) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] Onboard USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), cache line size 08
Interrupt: pin D routed to IRQ 4
Region 0: Memory at d2800000 (32-bit, non-prefetchable) [size=4K]

00:01.4 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 1473
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin B routed to IRQ 7
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at d2000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=55mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.6 Modem: Silicon Integrated Systems [SiS] Intel 537 [56k Winmodem] (rev a0) (prog-if 00 [Generic])
Subsystem: Asustek Computer, Inc.: Unknown device 1616
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at b800 [size=256]
Region 1: I/O ports at b400 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:02.0 PCI bridge: Silicon Integrated Systems [SiS] SiS 530 Virtual PCI-to-PCI bridge (AGP) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: d1800000-d1ffffff
Prefetchable memory behind bridge: d8000000-e7efffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:09.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 88)

	Subsystem: Asustek Computer, Inc.: Unknown device 1674
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 000de000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
	Memory window 0: 10400000-107ff000 (prefetchable)
	Memory window 1: 10800000-10bff000
	I/O window 0: 00004000-000040ff
	I/O window 1: 00004400-000044ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001

00:09.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 88)

	Subsystem: Asustek Computer, Inc.: Unknown device 1674
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
	Memory window 0: 10c00000-10fff000 (prefetchable)
	Memory window 1: 11000000-113ff000
	I/O window 0: 00004800-000048ff
	I/O window 1: 00004c00-00004cff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001

00:09.2 System peripheral: Ricoh Co Ltd: Unknown device 0576
Subsystem: Asustek Computer, Inc.: Unknown device 1674
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [disabled] [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+

00:0a.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 1677
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max), cache line size 08
Interrupt: pin A routed to IRQ 4
Region 0: Memory at d1000000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at d0800000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+

01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] SiS630 GUI Accelerator+3D (rev 31) (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 1672
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- BIST result: 00
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at d1800000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at a800 [size=128]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] AGP version 2.0
Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>