sysvinit/inittab: adjust shutdown
PATCH 1/1 sysvinit/inittab: adjust shutdown
The previous shutdown sequence was basically a no-op, it did't call rcK to stop anything and dumped users back into shell.
So do the proper thing by calling rcK for levels 0 (halt) and 6 (reboot), then swapoff, then remount ro.
After that call halt for 0 and reboot for 6.
Also make 3 the default runlevel as in normal distributions, for all intents and purposes it changes nothing except aesthetics/convention.
And make the labels a context sequence rather than just a short form of the actions which IMHO looks horrible.
--- package/sysvinit/inittab | 27 ++++++++++++++++----------- 1 file changed, 16 insertions(+), 11 deletions(-)
package/sysvinit/inittab +16 -11
@@ -2,21 +2,26 @@ # # This inittab is a basic inittab sample for sysvinit, which mimics # Buildroot's default inittab for BusyBox. -id:1:initdefault: +id:3:initdefault: -proc::sysinit:/bin/mount -t proc proc /proc -rwmo::sysinit:/bin/mount -o remount,rw / -dpts::sysinit:/bin/mkdir -p /dev/pts -dshm::sysinit:/bin/mkdir -p /dev/shm -moun::sysinit:/bin/mount -a -host::sysinit:/bin/hostname -F /etc/hostname -init::sysinit:/etc/init.d/rcS +si0::sysinit:/bin/mount -t proc proc /proc +si1::sysinit:/bin/mount -o remount,rw / +si2::sysinit:/bin/mkdir -p /dev/pts +si3::sysinit:/bin/mkdir -p /dev/shm +si4::sysinit:/bin/mount -a +si5::sysinit:/bin/hostname -F /etc/hostname +si6::sysinit:/etc/init.d/rcS # S0:1:respawn:/sbin/getty -L ttyS0 115200 vt100 # GENERIC_SERIAL # Stuff to do for the 3-finger salute -rebo::ctrlaltdel:/sbin/reboot +ca::ctrlaltdel:/sbin/reboot # Stuff to do before rebooting -umou:6:wait:/bin/umount -a -r -swap:6:wait:/sbin/swapoff -a +shd0:06:wait:/etc/init.d/rcK +shd1:06:wait:/sbin/swapoff -a +shd2:06:wait:/bin/umount -a -r + +# The usual halt or reboot actions +hlt0:0:wait:/sbin/halt -dhp +reb0:6:wait:/sbin/reboot
Signature · 1 line
2.0.4
PATCH 1/1 sysvinit/inittab: adjust shutdown
Quoted 8 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
"Gustavo" == Gustavo Zacarias <[email protected]> writes:
The previous shutdown sequence was basically a no-op, it did't call rcK to stop anything and dumped users back into shell.
So do the proper thing by calling rcK for levels 0 (halt) and 6 (reboot), then swapoff, then remount ro.
After that call halt for 0 and reboot for 6.
Quoted 7 lines
Also make 3 the default runlevel as in normal distributions, for all intents and purposes it changes nothing except aesthetics/convention.
And make the labels a context sequence rather than just a short form of the actions which IMHO looks horrible.
Signed-off-by Gustavo Zacarias <[email protected]>
Committed, thanks.
Signature · 1 line
Bye, Peter Korsgaard