Skip to contentSkip to conversation

2.6.25 DMA: Out of SW-IOMMU space - Asus M2N32 AMD 8GB memory

DISCUSSION Gerardo Exequiel Pozzi 3 participants 4 messages Aug 29, 2008

lore
Share & tools
lore
#0 lore raw

Hi

(sorry my english)

When booted kernel with no iommu parameter, it uses the iommu gart (from amd) and the size of the aperture is 64MB You can try to grow this size with iommu=memaper=2 for 128MB or 3 for 256MB. I don't have experience with this, but i read that this, solves the problem.

I have the similar hardware, but when boot in 64 bits, limit the memory with mem=4G (discarded 0.5G that are (remaped from pci space) beyond 4G) and iommu=noaperture. (This is not option for you, will be discard 4G of RAM)

Asus M2N32-SLI DELUXE (BIOS Phoenix ver 1603 [12/17/2007]) 4 x 1GB OCZ DDR2 PC2-6400 Platinum Rev2 ( OCZ2P800R21G ) AMD Athlon 64 X2 5200+ ( ADA5200IAA6CS ) (stepping F2)

I have realiced some test an posted here (sorry in spanish): http://www.pcmasmas.com/viewtopic.php?t=31445

Buena suerte.

Quoted 10 lines · Jari Aalto <jari.aalto <at> cante.net> writes:

Initially when the PC was installed (and had no IOMMU) options, that cause the whole harddisk to corrupt and I had to reinstall everything. It might have been a little older kernel (2.6.23?), but I don't recall it exactly.

According to messages in syslog I tried to track down similar incidents and found the iommu articles. But the information was like trial and error.

Would you suggest that "immu=off" would be best option?

Signature · 4 lines
Gerardo Exequiel Pozzi ( djgera )
http://www.djgera.com.ar
KeyID: 0x1B8C330D
Key fingerprint = 0CAA D5D4 CD85 4434 A219  76ED 39AB 221B 1B8C 330D
#1 lore raw
Quoted 4 lines · Gerardo Exequiel Pozzi

When booted kernel with no iommu parameter, it uses the iommu gart (from amd) and the size of the aperture is 64MB You can try to grow this size with iommu=memaper=2 for 128MB or 3 for 256MB. I don't have experience with this, but i read that this, solves the problem.

See my original bug report, which included experiences with memaper. Unofrtunately they didn't help:

    REF: http://article.gmane.org/gmane.linux.kernel/725293 (thread start)

but I'll try that once more with this 2.6.26 kernel to double check.

Quoted 4 lines

I have the similar hardware, but when boot in 64 bits, limit the memory with mem=4G (discarded 0.5G that are (remaped from pci space) beyond 4G) and iommu=noaperture. (This is not option for you, will be discard 4G of RAM)

Interestingly 'noaperture' together with 'noagp' has been the best option so far. It gives workign system for about week, but eventually the "out of IOMMU space" messages start appear.

The system has always seen the full 8 GB memory without problems.

Quoted 3 lines

Asus M2N32-SLI DELUXE (BIOS Phoenix ver 1603 [12/17/2007]) 4 x 1GB OCZ DDR2 PC2-6400 Platinum Rev2 ( OCZ2P800R21G ) AMD Athlon 64 X2 5200+ ( ADA5200IAA6CS ) (stepping F2)

The only difference to your system is more recent CPU:

$ cat/proc/cpuinfo

processor : 0
vendor_id : AuthenticAMD
cpu family : 15
model : 107
model name : AMD Athlon(tm) X2 Dual Core Processor BE-2400
stepping : 2
cpu MHz : 2310.516
cache size : 512 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 2
apicid : 0
initial apicid : 0
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt rdtscp lm 3dnowext 3dnow rep_good pni cx16 lahf_lm cmp_legacy svm extapic cr8_legacy 3dnowprefetch
bogomips : 4625.06
TLB size : 1024 4K pages
clflush size : 64
cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual
power management: ts fid vid ttp tm stc
...

Quoted 1 line

I have realiced some test an posted here (sorry in spanish): http://www.pcmasmas.com/viewtopic.php?t=31445

Could you explain this a bit more. Is the mentioned "tip-latest" the current kernel development tree? Should I try to compile this kernel and use it for testing?

Jari

#2 lore raw
In reply to Gerardo Exequiel Pozzi
Quoted 13 lines · Yinghai Lu
Quoted 11 lines · Jari Aalto
Quoted 8 lines · Krzysztof Halasa
Quoted 3 lines · Jari Aalto

What, if after booting to 2.6.26 and without any 'iommu' boot parameters, there still appears "Out of Iommu space" messages? What kind of logs should I post?

You shouldn't be getting "Out of SW-IOMMU space" messages when not using SW-IOMMU.

Quoted 7 lines
Quoted 5 lines

REF: http://article.gmane.org/gmane.linux.kernel/725293 (thread start)

I regret to report that:

- Upgraded to kernel 2.6.26-1-amd64 (Debian/unstable 2.6.26-3)

can you send out whole boot log? with "debug initcall_debug"

See below.

Quoted 1 line

http://people.redhat.com/mingo/tip.git/readme.txt

Could you explain this document a bit. What git commands should I use to retrive test kernel to build?

1 The vanilla boot. No IOMMU option, no SWIOTLB
http://sial.org/pbot/32038

2 with iommu=memaper=3
http://sial.org/pbot/32040

3 with iommu=memaper=3,noagp
http://sial.org/pbot/32041

4 with iommu=memaper=3,noagp,soft swiotlb=65535
http://sial.org/pbot/32042

I'm including the diff between [1] and [2]. The script I used is also attached.

Jari

# DESCRIPTION
#
# Take diffs between dmesg boot logs. After each boot, save log with:
#
# $ dmesg > dmesg-$(date +"%Y%m%d%h%m").log
#
# USAGE
#
#
# $ . kernel.bash
# $ Diff dmesg1.log dmesg2.log

Clean ()

{
    awk -F: '{$1=""; print}' "$1"
}

Diff ()

{
    ${test+echo} diff -bwu --label "$1" --label "$2" <(Clean "$1") <(Clean "$2")
}

# End of file

dmesg-2.6.26-20080829-memaper3.log renamed from dmesg-2.6.26-20080829-vanilla.log +80 -105
@@ -1,7 +1,7 @@
 
 
  09 32 UTC 2008
-  root=UUID=cb9d814f-d885-435b-8e6d-ac17c0ac5aa1 ro quiet vga=0x317 debug initcall_debug
+  root=UUID=cb9d814f-d885-435b-8e6d-ac17c0ac5aa1 ro quiet vga=0x317 iommu=memaper=3 debug initcall_debug single
  
   0000000000000000 - 000000000009f000 (usable)
   000000000009f000 - 00000000000a0000 (reserved)
@@ -103,13 +103,13 @@
   32, nr_cpu_ids  4
   2063260
   Normal
-  root=UUID=cb9d814f-d885-435b-8e6d-ac17c0ac5aa1 ro quiet vga=0x317 debug initcall_debug
+  root=UUID=cb9d814f-d885-435b-8e6d-ac17c0ac5aa1 ro quiet vga=0x317 iommu=memaper=3 debug initcall_debug single
 
   4096 (order  12, 32768 bytes)
   2000
 
 
-  Detected 2310.513 MHz processor.
+  Detected 2310.518 MHz processor.
   IRQ7.
   colour dummy device 80x25
 
@@ -120,9 +120,8 @@
 
 
 
-
-  Registered nosave memory  0000000004000000 - 0000000008000000
-  8194600k/9437184k available (2224k kernel code, 192468k reserved, 1080k data, 392k init)
+  Registered nosave memory  0000000020000000 - 0000000030000000
+  7997992k/9437184k available (2224k kernel code, 389076k reserved, 1080k data, 392k init)
   page pool initialized 1 of 1 pages preallocated
 
 
@@ -528,9 +527,9 @@
 
 
   Disabling AGP.
-  aperture base @ 4000000 size 65536 KB
+  aperture base @ 20000000 size 262144 KB
   using GART IOMMU.
-  Reserving 64MB of IOMMU area in the AGP aperture
+  Reserving 256MB of IOMMU area in the AGP aperture
 
 
   at MMIO 0xfefff000, IRQs 2, 8, 31
@@ -964,7 +963,7 @@
 
 
 
- 05  setting system clock to 2008-08-29 06 54 38 UTC (1219992878)
+ 05  setting system clock to 2008-08-29 06 57 31 UTC (1219993051)
 
 
 
@@ -978,124 +977,111 @@
   Expecting a [Reference] package element, found type 0
   LNXTHERM 01 is registered as thermal_zone0
   Thermal Zone [THRM] (40 C)
-  PCI Interrupt Link [APCL] enabled at IRQ 23
-  PCI Interrupt 0000 00 0a.1[B] -> Link [APCL] -> GSI 23 (level, low) -> IRQ 23
-  Setting latency timer of device 0000 00 0a.1 to 64
- 00 0a.1  EHCI Host Controller
- 00 0a.1  new USB bus registered, assigned bus number 1
- 00 0a.1  debug port 1
-  cache line size of 64 is not supported by device 0000 00 0a.1
- 00 0a.1  irq 23, io mem 0xfe02e000
-
   2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
+  PCI Interrupt Link [APCF] enabled at IRQ 23
+  PCI Interrupt 0000 00 0a.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23
+  Setting latency timer of device 0000 00 0a.0 to 64
+ 00 0a.0  OHCI Host Controller
+ 00 0a.0  new USB bus registered, assigned bus number 1
+ 00 0a.0  irq 23, io mem 0xfe02f000
+
 
 
- 00 0a.1  USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
   configuration #1 chosen from 1 choice
  1.0  USB hub found
  1.0  10 ports detected
   fd0 is 1.44M
 
-  New USB device found, idVendor=1d6b, idProduct=0002
-  New USB device strings  Mfr=3, Product=2, SerialNumber=1
-  Product  EHCI Host Controller
-  Manufacturer  Linux 2.6.26-1-amd64 ehci_hcd
-  SerialNumber  0000 00 0a.1
-  PCI Interrupt Link [APCF] enabled at IRQ 22
-  PCI Interrupt 0000 00 0a.0[A] -> Link [APCF] -> GSI 22 (level, low) -> IRQ 22
-  Setting latency timer of device 0000 00 0a.0 to 64
- 00 0a.0  OHCI Host Controller
- 00 0a.0  new USB bus registered, assigned bus number 2
- 00 0a.0  irq 22, io mem 0xfe02f000
-  configuration #1 chosen from 1 choice
- 1.0  USB hub found
- 1.0  10 ports detected
   New USB device found, idVendor=1d6b, idProduct=0001
   New USB device strings  Mfr=3, Product=2, SerialNumber=1
   Product  OHCI Host Controller
   Manufacturer  Linux 2.6.26-1-amd64 ohci_hcd
   SerialNumber  0000 00 0a.0
+  PCI Interrupt Link [APCL] enabled at IRQ 22
+  PCI Interrupt 0000 00 0a.1[B] -> Link [APCL] -> GSI 22 (level, low) -> IRQ 22
+  Setting latency timer of device 0000 00 0a.1 to 64
+ 00 0a.1  EHCI Host Controller
+ 00 0a.1  new USB bus registered, assigned bus number 2
+ 00 0a.1  debug port 1
+  cache line size of 64 is not supported by device 0000 00 0a.1
+ 00 0a.1  irq 22, io mem 0xfe02e000
+ 00 0a.1  USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
+  configuration #1 chosen from 1 choice
+ 1.0  USB hub found
+ 1.0  10 ports detected
+  New USB device found, idVendor=1d6b, idProduct=0002
+  New USB device strings  Mfr=3, Product=2, SerialNumber=1
+  Product  EHCI Host Controller
+  Manufacturer  Linux 2.6.26-1-amd64 ehci_hcd
+  SerialNumber  0000 00 0a.1
   Reverse Engineered nForce ethernet driver. Version 0.61.
   PCI Interrupt Link [APCH] enabled at IRQ 21
   PCI Interrupt 0000 00 10.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 21
   Setting latency timer of device 0000 00 10.0 to 64
-  new high speed USB device using ehci_hcd and address 3
-  configuration #1 chosen from 1 choice
-  New USB device found, idVendor=0781, idProduct=5406
-  New USB device strings  Mfr=1, Product=2, SerialNumber=3
-  Product  U3 Cruzer Micro
-  Manufacturer  SanDisk Corporation
-  SerialNumber  0000162152754B6C
-
  00 10.0  ifname eth0, PHY OUI 0x5043 @ 1, addr 00 18 f3 84 26 c0
  00 10.0  highdma csum vlan pwrctl mgmt timirq gbit lnktim msi desc-v3
   PCI Interrupt Link [AMC1] enabled at IRQ 20
   PCI Interrupt 0000 00 11.0[A] -> Link [AMC1] -> GSI 20 (level, low) -> IRQ 20
   Setting latency timer of device 0000 00 11.0 to 64
-  new high speed USB device using ehci_hcd and address 4
+  new high speed USB device using ehci_hcd and address 3
   configuration #1 chosen from 1 choice
   New USB device found, idVendor=0781, idProduct=5406
   New USB device strings  Mfr=1, Product=2, SerialNumber=3
   Product  U3 Cruzer Micro
   Manufacturer  SanDisk Corporation
-  SerialNumber  000016215275A63E
-  new high speed USB device using ehci_hcd and address 5
+  SerialNumber  0000162152754B6C
  00 11.0  ifname eth1, PHY OUI 0x5043 @ 1, addr 00 18 f3 84 36 c0
  00 11.0  highdma csum vlan pwrctl mgmt timirq gbit lnktim msi desc-v3
   PCI Interrupt Link [APC1] enabled at IRQ 16
   PCI Interrupt 0000 02 0b.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
   fw-host0  OHCI-1394 1.1 (PCI)  IRQ=[16]  MMIO=[fdfff000-fdfff7ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
- 00 0d.0  version 3.5
+
  03 00.0  version 1.1
+  PCI Interrupt Link [APC7] enabled at IRQ 16
+  PCI Interrupt 0000 03 00.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 16
+  Setting latency timer of device 0000 03 00.0 to 64
+ 00 0d.0  version 3.5
   PCI Interrupt Link [APSI] enabled at IRQ 23
   PCI Interrupt 0000 00 0d.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 23
  00 0d.0  Using SWNCQ mode
   Setting latency timer of device 0000 00 0d.0 to 64
-  PCI Interrupt Link [APC7] enabled at IRQ 16
-  PCI Interrupt 0000 03 00.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 16
-  Setting latency timer of device 0000 03 00.0 to 64
-
   Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
-  sata_nv
   sata_sil24
+  sata_nv
   sata_sil24
   SATA max UDMA/100 host m128@0xfdeff000 port 0xfdef8000 irq 16
   SATA max UDMA/100 host m128@0xfdeff000 port 0xfdefa000 irq 16
   sata_nv
   SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xe000 irq 23
   SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xe008 irq 23
+
+  new high speed USB device using ehci_hcd and address 4
   configuration #1 chosen from 1 choice
-  New USB device found, idVendor=0bda, idProduct=8187
+  New USB device found, idVendor=0781, idProduct=5406
   New USB device strings  Mfr=1, Product=2, SerialNumber=3
-  Product  RTL8187_Wireless
-  Manufacturer  Manufacturer_Realtek_RTL8187_
-  SerialNumber  0015AF0B59A6
-  new low speed USB device using ohci_hcd and address 2
+  Product  U3 Cruzer Micro
+  Manufacturer  SanDisk Corporation
+  SerialNumber  000016215275A63E
+  new high speed USB device using ehci_hcd and address 5
   SATA link up 3.0 Gbps (SStatus 123 SControl 300)
   ATA-7  ST31000340AS, SD01, max UDMA/133
   1953525168 sectors, multi 1  LBA48 NCQ (depth 31/32)
   configured for UDMA/133
   configuration #1 chosen from 1 choice
-  New USB device found, idVendor=046d, idProduct=c50c
-  New USB device strings  Mfr=1, Product=2, SerialNumber=0
-  Product  USB Receiver
-  Manufacturer  Logitech
+  New USB device found, idVendor=0bda, idProduct=8187
+  New USB device strings  Mfr=1, Product=2, SerialNumber=3
+  Product  RTL8187_Wireless
+  Manufacturer  Manufacturer_Realtek_RTL8187_
+  SerialNumber  0015AF0B59A6
   SCSI emulation for USB Mass Storage devices
   SCSI emulation for USB Mass Storage devices
-  registered new interface driver usb-storage
-
-  registered new interface driver hiddev
   device found at 3
   waiting for device to settle before scanning
+  registered new interface driver usb-storage
+
   device found at 4
   waiting for device to settle before scanning
-  Logitech USB Receiver as /class/input/input1
-  USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000 00 0a.0-2
-
-  Logitech USB Receiver as /class/input/input2
-  USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000 00 0a.0-2
-  registered new interface driver usbhid
-  v2.6 USB HID core driver
+  new low speed USB device using ohci_hcd and address 2
   SATA link up 1.5 Gbps (SStatus 113 SControl 300)
   ATAPI  TSSTcorp CDDVDW SH-S203N, SB00, max UDMA/100
   configured for UDMA/100
@@ -1109,7 +1095,20 @@
   sata_nv
   SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xcc00 irq 22
   SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xcc08 irq 22
+  configuration #1 chosen from 1 choice
+  New USB device found, idVendor=046d, idProduct=c50c
+  New USB device strings  Mfr=1, Product=2, SerialNumber=0
+  Product  USB Receiver
+  Manufacturer  Logitech
+  registered new interface driver hiddev
+  Logitech USB Receiver as /class/input/input1
+  USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000 00 0a.0-2
   Host added  ID BUS[0-00 1023]  GUID[0011d80000eaece5]
+
+  Logitech USB Receiver as /class/input/input2
+  USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000 00 0a.0-2
+  registered new interface driver usbhid
+  v2.6 USB HID core driver
   SATA link down (SStatus 0 SControl 300)
   SATA link down (SStatus 0 SControl 300)
   PCI Interrupt Link [ASA2] enabled at IRQ 21
@@ -1152,11 +1151,11 @@
 
   mounted filesystem with ordered data mode.
   device scan complete
-  device scan complete
- 0 0 0  Direct-Access     SanDisk  U3 Cruzer Micro  3.27 PQ  0 ANSI  2
  0 0 0  Direct-Access     SanDisk  U3 Cruzer Micro  3.27 PQ  0 ANSI  2
  0 0 1  CD-ROM            SanDisk  U3 Cruzer Micro  3.27 PQ  0 ANSI  2
  0 0 0  [sdb] 8015502 512-byte hardware sectors (4104 MB)
+  device scan complete
+ 0 0 0  Direct-Access     SanDisk  U3 Cruzer Micro  3.27 PQ  0 ANSI  2
  0 0 0  [sdb] Write Protect is off
  0 0 0  [sdb] Mode Sense  03 00 00 00
  0 0 0  [sdb] Assuming drive cache  write through
@@ -1166,8 +1165,8 @@
  0 0 0  [sdb] Assuming drive cache  write through
   sdb1
  0 0 0  [sdb] Attached SCSI removable disk
- 0 0 0  Attached scsi generic sg2 type 0
  0 0 1  CD-ROM            SanDisk  U3 Cruzer Micro  3.27 PQ  0 ANSI  2
+ 0 0 0  Attached scsi generic sg2 type 0
   scsi3-mmc drive  8x/40x writer xa/form2 cdda tray
  0 0 1  Attached scsi CD-ROM sr1
  0 0 1  Attached scsi generic sg3 type 5
@@ -1193,17 +1192,17 @@
   nForce2 SMBus adapter at 0x1c00
   nForce2 SMBus adapter at 0x1c40
   PC Speaker as /class/input/input5
+  Selected rate control algorithm 'pid'
+  Driver 'pcspkr' is already registered, aborting...
   PCI Interrupt Link [AAZA] enabled at IRQ 20
   PCI Interrupt 0000 00 0e.1[B] -> Link [AAZA] -> GSI 20 (level, low) -> IRQ 20
   Setting latency timer of device 0000 00 0e.1 to 64
-  Driver 'pcspkr' is already registered, aborting...
-  Selected rate control algorithm 'pid'
   the driver 'parport_pc' has been registered
  0a  reported by Plug and Play ACPI
   PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
- 0a  driver attached
   hwaddr 00 15 af 0b 59 a6, rtl8187 V1 + rtl8225z2
   registered new interface driver rtl8187
+ 0a  driver attached
 
   module loaded
   module license 'NVIDIA' taints kernel.
@@ -1223,43 +1222,19 @@
   Registered protocol family 10
   Disabled Privacy Extensions
   wlan0  link is not ready
-  Registered udp transport module.
-  Registered tcp transport module.
-
-  Found 1 AMD Athlon(tm) X2 Dual Core Processor BE-2400 processors (2 cpu cores) (version 2.20.00)
-  ACPI Processor support is required for SMP systems but is absent. Please load the ACPI Processor module before starting this driver.
-  ACPI Processor support is required for SMP systems but is absent. Please load the ACPI Processor module before starting this driver.
+  Initial auth_alg=0
+  authenticate with AP 00 18 39 c0 4f 1b
   Initial auth_alg=0
   authenticate with AP 00 18 39 c0 4f 1b
   RX authentication from 00 18 39 c0 4f 1b (alg=0 transaction=2 status=0)
   authenticated
   associate with AP 00 18 39 c0 4f 1b
+  authentication frame received from 00 18 39 c0 4f 1b, but not in authenticate state - ignored
   RX AssocResp from 00 18 39 c0 4f 1b (capab=0x411 status=0 aid=1)
   associated
   switched to short barker preamble (BSSID=00 18 39 c0 4f 1b)
   wlan0  link becomes ready
-  using parport0 (interrupt-driven).
-  user-space parallel port driver
-  Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
-  starting 90-second grace period
-  Trying to deactivate the NMI watchdog permanently...
-  Successfully done.
-  Found 2 processor cores.
-  fAsync=1 u64DiffCores=1150118.
-  TSC mode is 'asynchronous', kernel timer mode is 'normal'.
-  Successfully loaded version 1.6.2_OSE (interface 0x00070002).
-  `ntpd' uses 32-bit capabilities (legacy support in use)
+  Registered udp transport module.
+  Registered tcp transport module.
+
   no IPv6 routers present
-  Core ver 2.11
-  Registered protocol family 31
-  HCI device and connection manager initialized
-  HCI socket layer initialized
-  L2CAP ver 2.9
-  L2CAP socket layer initialized
-  RFCOMM socket layer initialized
-  RFCOMM TTY layer initialized
-  RFCOMM ver 1.8
-  no link during initialization.
-  eth1  link is not ready
-  no link during initialization.
-  eth0  link is not ready
#3 lore raw
Quoted 19 lines · Jari Aalto
Quoted 19 lines · Jari Aalto
Quoted 17 lines
Quoted 8 lines · Krzysztof Halasa
Quoted 3 lines · Jari Aalto

What, if after booting to 2.6.26 and without any 'iommu' boot parameters, there still appears "Out of Iommu space" messages? What kind of logs should I post?

You shouldn't be getting "Out of SW-IOMMU space" messages when not using SW-IOMMU.

REF: http://article.gmane.org/gmane.linux.kernel/725293 (thread start)

I regret to report that:

- Upgraded to kernel 2.6.26-1-amd64 (Debian/unstable 2.6.26-3)

Quoted 8 lines
Quoted 1 line

can you send out whole boot log? with "debug initcall_debug"

See below.

Quoted 1 line

http://people.redhat.com/mingo/tip.git/readme.txt

Could you explain this document a bit. What git commands should I use to retrive test kernel to build?

mkdir linux.trees.git || exit -1
cd linux.trees.git

git init
git remote add linus
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git

git remote add tip
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip.git

git remote update

git checkout -b tip-latest tip/master

can you fix your mail client? it stripped Cc and automatically?

YH