printk: Document that CONFIG_BOOT_PRINTK_DELAY required for boot_delay=
PATCH v2 1/1 printk: Document that CONFIG_BOOT_PRINTK_DELAY required for boot_delay=
From: Bjorn Helgaas <[email protected]>
Document the fact that CONFIG_BOOT_PRINTK_DELAY must be enabled for the "boot_delay" kernel parameter to work. Also mention that "lpj=" may be necessary.
---
Changes from v1 (https://lore.kernel.org/all/[email protected]/):
- Clarify use of "lpj=". Reword consequences of delay larger than 10000.
Documentation/admin-guide/kernel-parameters.txt | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)
Documentation/admin-guide/kernel-parameters.txt +4 -2
@@ -480,8 +480,10 @@ See Documentation/block/cmdline-partition.rst boot_delay= Milliseconds to delay each printk during boot. - Values larger than 10 seconds (10000) are changed to - no delay (0). + Only works if CONFIG_BOOT_PRINTK_DELAY is enabled, + and you may also have to specify "lpj=". Boot_delay + values larger than 10 seconds (10000) are assumed + erroneous and ignored. Format: integer bootconfig [KNL]
Signature · 1 line
2.25.1
Quoted 7 lines · Bjorn Helgaas
From: Bjorn Helgaas <[email protected]>
Document the fact that
CONFIG_BOOT_PRINTK_DELAYmust be enabled for the "boot_delay" kernel parameter to work. Also mention that "lpj=" may be necessary.Signed-off-by Bjorn Helgaas <[email protected]>
Thanks.
Quoted 24 lines
---
Changes from v1 (https://lore.kernel.org/all/[email protected]/):
- Clarify use of "lpj=". Reword consequences of delay larger than 10000.Documentation/admin-guide/kernel-parameters.txt | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)Documentation/admin-guide/kernel-parameters.txt +4
-2@@ -480,8 +480,10 @@ See Documentation/block/cmdline-partition.rst boot_delay= Milliseconds to delay each printk during boot. - Values larger than 10 seconds (10000) are changed to - no delay (0). + Only works if CONFIG_BOOT_PRINTK_DELAY is enabled, + and you may also have to specify "lpj=". Boot_delay + values larger than 10 seconds (10000) are assumed + erroneous and ignored. Format: integer bootconfig [KNL]
Signature · 1 line
~Randy
Quoted 19 lines · Bjorn Helgaas
From: Bjorn Helgaas <[email protected]>
Document the fact that
CONFIG_BOOT_PRINTK_DELAYmust be enabled for the "boot_delay" kernel parameter to work. Also mention that "lpj=" may be necessary.Signed-off-by Bjorn Helgaas <[email protected]>---
Changes from v1 (https://lore.kernel.org/all/[email protected]/):
- Clarify use of "lpj=". Reword consequences of delay larger than 10000.Documentation/admin-guide/kernel-parameters.txt | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)Documentation/admin-guide/kernel-parameters.txt +0
-0
Documentation/admin-guide/kernel-parameters.txt line 487
Quoted 10 lines
Documentation/admin-guide/kernel-parameters.txt +4
-2@@ -480,8 +480,10 @@ See Documentation/block/cmdline-partition.rst boot_delay= Milliseconds to delay each printk during boot. - Values larger than 10 seconds (10000) are changed to - no delay (0). + Only works if CONFIG_BOOT_PRINTK_DELAY is enabled, + and you may also have to specify "lpj=". Boot_delay + values larger than 10 seconds (10000) are assumed + erroneous and ignored. Format: integer
Applied, thanks.
jon