remove Attach another file remove Attach another file remove Attach another file USB mass storage not always detecting my 1GB PQI intelligent stick
Hello,
my 1 GB PQI Intelligent Stick is often not beeing used by mass storage driver when I plug it.
Quoted 1 line
From a fresh reboot it works, I see:
Jan 9 16:54:43 parachute kernel: usb 1-3: new high speed USB device
using ehci_hcd and address 2
Jan 9 16:54:43 parachute kernel: scsi0 : SCSI emulation for USB Mass
Storage devices
Jan 9 16:54:48 parachute kernel: Vendor: I-Stick2 Model:
IntelligentStick Rev: 2.00
Jan 9 16:54:48 parachute kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jan 9 16:54:49 parachute kernel: sda: Unit Not Ready, sense:then a lot of other stuff, and I can use it.
But if I unplug/replug it, it's not longer detected as mass storage device. I can see 3 new USB devices detected when I plug it:
kernel: usb 1-3: new high speed USB device using ehci_hcd and address 6
kernel: usb 3-1: new full speed USB device using uhci_hcd and address 4
kernel: usb 3-1: new full speed USB device using uhci_hcd and address 5
But it's no longer beeing detected as mass storage.
I have other USB 2.0 keys which are working perfectly. Moreover this USB key seems to work properly on some other machines/OSes
In the attached file, full log and result of lspci.
Roseline
Jan 9 16:54:43 parachute kernel: usb 1-3: new high speed USB device using ehci_hcd and address 2 Jan 9 16:54:43 parachute kernel: scsi0 : SCSI emulation for USB Mass Storage devices Jan 9 16:54:48 parachute kernel: Vendor: I-Stick2 Model: IntelligentStick Rev: 2.00 Jan 9 16:54:48 parachute kernel: Type: Direct-Access ANSI SCSI revision: 02 Jan 9 16:54:49 parachute kernel: sda: Unit Not Ready, sense: Jan 9 16:54:49 parachute kernel: Current : sense = 70 6 Jan 9 16:54:49 parachute kernel: ASC=28 ASCQ= 0 Jan 9 16:54:49 parachute kernel: Raw sense data:0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x28 0x00 0x00 0x00 0x00 0x00 Jan 9 16:54:49 parachute kernel: sda : READ CAPACITY failed. Jan 9 16:54:49 parachute kernel: sda : status=1, message=00, host=0, driver=08 Jan 9 16:54:49 parachute kernel: Current sd: sense = 70 6 Jan 9 16:54:49 parachute kernel: ASC=28 ASCQ= 0 Jan 9 16:54:49 parachute kernel: Raw sense data:0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x28 0x00 0x00 0x00 0x00 0x00 Jan 9 16:54:49 parachute kernel: sda: assuming Write Enabled Jan 9 16:54:49 parachute kernel: sda: Unit Not Ready, sense: Jan 9 16:54:49 parachute kernel: Current : sense = 70 6 Jan 9 16:54:49 parachute kernel: ASC=28 ASCQ= 0 Jan 9 16:54:49 parachute kernel: Raw sense data:0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x28 0x00 0x00 0x00 0x00 0x00 Jan 9 16:54:49 parachute kernel: sda : READ CAPACITY failed. Jan 9 16:54:49 parachute kernel: sda : status=1, message=00, host=0, driver=08 Jan 9 16:54:49 parachute kernel: Current sd: sense = 70 6 Jan 9 16:54:49 parachute kernel: ASC=28 ASCQ= 0 Jan 9 16:54:49 parachute kernel: Raw sense data:0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x28 0x00 0x00 0x00 0x00 0x00 Jan 9 16:54:49 parachute kernel: sda: assuming Write Enabled Jan 9 16:54:49 parachute kernel: SCSI device sda: 2047488 512-byte hdwr sectors (1048 MB) Jan 9 16:54:49 parachute kernel: sda: assuming Write Enabled Jan 9 16:54:49 parachute kernel: /dev/scsi/host0/bus0/target0/lun0:<7>usb-storage: queuecommand called Jan 9 16:54:49 parachute kernel: p1 p2 Jan 9 16:54:49 parachute kernel: Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0 Jan 9 16:54:49 parachute kernel: Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 Jan 9 16:55:19 parachute kernel: usb 1-3: USB disconnect, address 2
< I unplug/replug >
Jan 9 17:07:17 parachute kernel: usb 1-3: new high speed USB device using ehci_hcd and address 6 Jan 9 17:07:17 parachute kernel: usb 3-1: new full speed USB device using uhci_hcd and address 4 Jan 9 17:07:18 parachute kernel: usb 3-1: new full speed USB device using uhci_hcd and address 5
< I unplug/replug >
Jan 9 17:10:21 parachute kernel: usb 1-3: new high speed USB device using ehci_hcd and address 7 Jan 9 17:10:21 parachute kernel: usb 3-1: new full speed USB device using uhci_hcd and address 6 Jan 9 17:10:22 parachute kernel: usb 3-1: new full speed USB device using uhci_hcd and address 7
--------------
result of lspci:
0000:00:00.0 Host bridge: Intel Corp. 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 02) 0000:00:01.0 PCI bridge: Intel Corp. 82845G/GL[Brookdale-G]/GE/PE Host-to-AGP Bridge (rev 02) 0000:00:1d.0 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 02) 0000:00:1d.1 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 02) 0000:00:1d.2 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 02) 0000:00:1d.7 USB Controller: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller (rev 02) 0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 82)
0000:00:1f.0 ISA bridge: Intel Corp. 82801DB/DBL (ICH4/ICH4-L) LPC Bridge (rev 02)
Quoted 6 lines · mama Smurf
Hello,
my 1 GB PQI Intelligent Stick is often not beeing used by mass storage driver when I plug it.
Do you have several different USB devices connected in the same time? It is possible that devices with different USB speed (high/full) cannot work together. I am not the kernel developer but this is just my experience with latest Linux distributions. The situation can be different with current USB developments.
regards,
Indrek
Quoted 5 lines
Do you have several different USB devices connected in the same time? It is possible that devices with different USB speed (high/full) cannot work together. I am not the kernel developer but this is just my experience with latest Linux distributions. The situation can be different with current USB developments.
I tried to remove every other USB device. What is really strange is that it works when I've just booted Linux, but if I unplug/replug the device it seems to be "detected", but is not listed in /proc/bus/usb/devices
Which distro/kernel do you have? Have you looked at your distro's bugzilla/buglist? Have you all latest update packages installed?
Quoted 22 lines · Roseline Bonchamp
Quoted 7 lines
Do you have several different USB devices connected in the same time? It is possible that devices with different USB speed (high/full) cannot work together. I am not the kernel developer but this is just my experience with latest Linux distributions. The situation can be different with current USB developments.
I tried to remove every other USB device. What is really strange is that it works when I've just booted Linux, but if I unplug/replug the device it seems to be "detected", but is not listed in
/proc/bus/usb/devices
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/.
Quoted 3 lines
Which distro/kernel do you have? Have you looked at your distro's bugzilla/buglist? Have you all latest update packages installed?
I use kernel 2.6.10 vanilla.
The distro has nothing to do here I suppose, but it's debian unstable.